Digital PDFs

EK-105AA-OW-001

January 1987

168 pages

Original

35MB

view download

OCR Version

17MB

view download

Document:	VAXstationII/GPX Owner's Manual, BA123 Enclosure
Order Number:	EK-105AA-OW
Revision:	001
Pages:	168
Original Filename:

OCR Text

VAXstation ll/GPX Owner’'s Manual,
BA123 Enclosure
Order No. EK-105AA-OW-001

digital jqulpmom corporation
maynard, massachusetts

First printing, January 1986
Revised, February 1987
The information in this document is subject to change without notice and should not be construed as a
commitment by Digital Equipment Corporation.
Digital Equipment Corporation assumes no responsibility for any errors that may appear in this document.

The software, if any, described in this document is furnished under a license and may be used or copied only
in accordance with the terms of such license. No responsibilityis assumed for the use or reliability of software
or equipment thatis not supplied by Digital Equipment Corporation or its affiliated companies.
Copyright ©1986, 1987 by Digital Equipment Corporation.
All Rights Reserved.

The READER’S COMMENTS form on the last page of this document requests the user’s critical evaluation to
assist in preparing future documentation.

The following are trademarks of Digital Equipment Corporation:

DEBET

DIBOL

ThinWire

DEC

MASSBUS

ULTRIX-32

DECconnect

MicroVAX

ULTRIX-32m

DECmate

MicroVMS

UNIBUS

DECnet

PDP

VAX

DECUS

P/OS

DECwriter

Professional

DELNI

Q-bus

VMS

DEMPR

Rainbow

DEQNA

RSTS

Work Processor

DEON;

digital

DEUNA

VAXcluster

VAXstation

1’«’(JS'I‘L"SCF&IP'I“m is a trademark of Adobe Systems, Inc.

Tefiktranix® is a registered trademark of Tektronix, Inc.

UNIX® is a registered trademark of American Telephone & Telegraph Company.
ML-5635

FCC NOTICE: The equipment described in this manual generates, uses, and may emit radio frequency
energy. The equipment has been type tested and found to comply with the limits for a Class A computing
device pursuant to Subpart ] of Part 15 of FCC Rules, which are designed to provide reasonable protection
against such radio frequency interference when operated in a commercial environment. Operation of this
equipment in a residential area may cause interference, in which case the user at his own expense may be
required to take measures to correct the interference.

Contents
Preface

Description of the VAXstation II/GPX

. ................... ix

Conventions Used in This Document . .. ........... C e e
eX
Structure of This Document . . ............. e

e . xi

Part I: Base System Installation . . ............. Ce xi
PartII: Operation. . . .. ...........
... ... ... ..., xi

Part I Options. . . . ... oot v, e xi

Part IV: Troubleshooting . .. ...................... xi
Part V: Appendixes

. .............
... ... .. .. xi

Part VI: Glossary . .. ................ e
Intended Audience . . .. ............ C et

et et

e xii
e

e xii

Part I: Base System Installation
Chapter 1

Preparing for Installation

Check Your Shipment.

. ............... e

Site-Preparation Review

......... C e eae

e e

1-1

s e 1-3

Space Planning . ............ Cettt
s e e 1-3
The System Unit . . .. .............. Ce e 1-3
The Color Monitor . . . .......... e

1-4

Electrical Requirements . . .. .....................

1-5

Environment . . . ... ... ettt
i e e i e, 1-6
Temperature
and Humidity

. ................

1-6

Static Electricity . . . . ... ..................

Clean Area . ...... e e

e e

1-7

Supplies Storage . ......... ee ..

1.7

Chapter 2

Setting Up the Hardware

Setting Up the Color Monmitor . . . .. .................. 2-2

Setting Up the Keyboard and Pointing Device

............ 2-6

Connecting the VAXstation II/GPX to a Power Source . . . ...

2-10

Connecting the VAXstation II/GPX to a Network

2-19

... ......

Connecting the Ethernet Transceiver Cable to the Workstation 2-19

Connecting to Standard Ethernet .. ................

2-20

Connecting to ThinWire Ethernet Using the DESTA . . . . ..

2-21

Testing the VAXstation II/GPX . ........... [

2-24

Part Il: Operation

Chapter 3

VAXstation Il/GPX Hardware

VAXstation II/GPX Controls and Indicators . . ... e

e e 3-1

Halt Enable/Disable Switch (2-position toggle switch).

. . . .. 3-3

Power-Up Mode Selection (3-position rotary switch) . . . . . .. 3-4
Baud Rate Selection Switch (8-position rotary switch) . . .. .. 3-4
Light-Emitting Diode (LED) Display

................. 3-4

Printer Port . .. ..............
... ... ee
e .. 3-4

The System Power Switch

....................... 3-4

The Restart/Run Pushbutton . . . ... ............. ... 35
The DC OK Indicator.

. .. ............ e
e e coo. 35

The Halt Pushbutton . . ... ... ..e Ce e Ce e 3-6
The Fixed Disk Pushbuttons

. . .................... 3-8

Turning On the System . . . . .................. co.. 3-8
Initial Control Panel Switch Settings . . . .. ...
. Cee 3-9
Turning Off the System . . . . .. ...

... ...

. ...,

3-10

Color Monitor Controls and Indicators

. ...............

3-10

. .............
... ... .. .. ......

3-13

Fixed Disk Drive

Tape Drive . . . ... ... . ...
Inserting a Tape Cartridge. . . . . e

i
e

...

3-13

e e e ..

3-14

Rewinding and Unloading a Tape Cartndge ...........

3-16

Protecting Tape Cartridges from Accidental Overwriting

3-18

...

Handling and Storing Tape Cartridges . . . . . . e e e 3-19
Dual
Diskette Drive . .......... e e e e Ce 3-19
InsertmgaDnskette.....,,,‘...,. ........ e,

3222

Protecting Diskettes from Accidental Overwnnng ..... ..

3-23

Handling and Storing Diskettes . . . . ... ............

3-23

Back-up Copies . . . . ... ittt

3-24

Part Ill; Ortiom
Chapter 4

Options

Hard-Copy Output Devices . . ........................ 4-2

Printers . ................... e Cee e ce. 4-2
TheLNO3

.......... ee e Y
-

The LNO3 PLUS ......... e e e 4-3
The PrintServer 40 (LPS40) . ................ 4-4

The LA210 . .. ..............S .. 46
The LA75

........ Ce
ee e

The LAS0

..... e e e e

The LCGO01

e e e 4-7
e e 4-8

..... e e

Plotter . . . ............... e

e e 4-9

e e

4-10

The LVP16 ...........................

4-10

Printer and Plotter Connection to the System . . ........

4-11

Input Devices . . .................. e
The Tablet . ........ Ce e e

The Mouse
..
....... e
Memory...........coovin.. C

e .

4-13

e .

4-13

e e e e

e e c... 4-14
e

e e

4-14

The Memory Modules . . . ...
.. N

4-14

Video .. ... . i
e e ..

4-15

The Video Subsystem ............ C i

e e

4-15

Storage Devices . . . ... ............ Cvae
ke s v ena e .

4-16

The Fixed Disk Drives . . . . . ........ G

4-16

...

4-17

. .. .. e e ek eee e
e e e ...

4-17

The Tape Drive . . . .. ..... ... ..

The Dual Diskette Drive

e e s

ee e

e e

Communications . ... .............
..
...

4-18

The Ethernet Communication Modules . . .. ..........

4-18

ThinWire Ethernet Components

. ........A

4-19

ThinWire Ethernet Cable . . . ... ...........

4-19

Connectors . . .................. oo

e. .

4-19

. .........

4-19

..............

4-19

Barrel Connectors and T-Connectors
DESTA and Transceiver Cable
Terminators

.. ... ... Cee e

e ... .

4-20

Connectors and Terminators . . . ....... T . 4-20

Additional Equipment . . . . ... .... ... .. e

421

DIGITAL ThinWire Ethernet Station Adapter (DESTA)4-21

Modems.......................... R

4-22

DF224 . . . . .. . e ..

4-22

DF124 . . . . .. .. e,

4-22

DF112 . . . . e

4-23

DFO3.

... . e

4-23

The DZQ11 Asynchronous Multiplexer . . . ...........

4-23

The DHV11 Asynchronous Multiplexer . . . . .......... 4-24
The DMV11 Synchronous Line Controller . . ..........

4-24

The DPV11 Synchronous Line Controller ............ 4-26
The KMV11 Programmable Controller

.. ............

4-27

Part IV: Troublaahooting

Chapter 5

Troubleshooting Procedure

Power-up Messages

. . ................. e 5-1

Basic Troubleshooting . . . .. ... ..........
... ... ..... 5-2

Replacingthe Fuse . . . .

... ...................

5-10

ColorMonitor . . . .............c.0
...

5-10

Mouse Maintenance .......... S
RS S
O

5-13

MicroVAX Diagnostic Monitor

. . .....................

The MicroVAX Diagnostic Monitor Main Menu

5-17

. .......

5-17

The System Utilittes Menu . . . ... ................

5-19

Chapter 6

Service

Part V: Aggandixas

Appendix A

_VAXstation Il/GPX System Specifications

Appendix B

VAXstation Il/GPX Related Documents

e e e B-1
e G
Hardware. . . .. . oo v v e e i eeienee
ULTRIX SOftware uuuuuuu 5 % W B B W B B A % % B & & B 4 & 8 & & & B & & 5 B ‘B" 2
MimVMS SOftware """"" * L] * * * * » L] *® [ *® - L] * % & ® & # ® # 8 & % @& B“4

Part Vl Gloasag

Glossary

Index

Figures
1-1
1-2
1-3
2-1
2-2
2-3
2-4
2-5

A VAXstation II/GPX in the BA123 Enclosure . ............ 1-1
Dimensions of the System Unit. ... ... e PP Cee 1-4
Dimensions of the Color Monitor . ........... e 1-5
Keyboard Connection, Color Monitor . . . . . e e e 2-7
Pointing Device Connection, Color Monitor . . . ... .. e 2-9
Monitor Connection to System Unit . . . ... ............. 2-13
Connection to Power Source, Color Monitor . . .......... . 2-17
System Connection to a DELNI. ......... e2-20

3-1

Controls and Indicators . . . ......................... 3-2

3-2

The CPU Distribution Panel . . . ... ........ e 3-3

3-3

Front and Side Controls, Color Monitor

3-4

Rear Controls and Connectors, Color Monitor

. ...............
............

3-11
3-12

4-1

The LNO3....... e e L. 43

4-2

The PrintServer 40 (LPS40)

4-3

The LA210 . . . .. . .

4-4

TheLA75............. e

. ................ e

oot

it
e

e 4-5

e e e e ... 4-6
e

e e 4-8

4-5

The LAS0...................... e 4-9

4-6

Printer and Plotter Connection to the System . . . . .........

4-12

4-7

TheTablet ... .. ... ... ... .. . ..

4-13

4-8

Connectors . . ... ..ottt
e e e
e e

4-20
4-21

4-9

DIGITAL ThinWire Ethernet Station Adapter (DESTA) .......

5-1

System Circuit Breaker . .. .. e

5-2

Fuse Location, Color Monitor . . ... ... e

e 5-3

e e-

5-11

Tables
3-1

Normal Power-On Indications

3-2

Tape Drive Controls and Indicators . . .................

............... e 3-9
3-17

4-16

4-1

Optional Storage Devices

5-1

System Unit Troubleshooting Procedures

. ....................... .

5-2

Fixed Disk and Diskette Drives Troubleshooting Procedures

5-3

Tape Drive Troubleshooting Procedures

................ 5-3

5-4

Monitor Troubleshooting Procedures

5-5

Pointing Device Troubleshooting Procedures

A-1 System Electrical Requirements

. .................. 5-8
.............-

5-10

. ............e A-1

A-2 System Environmental Requirements

A-3 Color Monitor Specifications

... 5-6

................. 5-7

........ ee A-2

. ........... e A-2

A-4 Mouse Specifications

.. ..........
.. ... ... . . 0., A-4

A-5 Tablet Specifications

.. ....................... ... AS

A-6 RD53 Fixed Disk Drive Specifications

. ................ A7

A-7 RD54 Fixed Disk Drive Specifications

.....
.. e
a e Ce e A-8

A-8 RX50 Dual Diskette Drive Specifications . ........... e A-8
*A-9 TK50 Tape Drive Specifications

viii

. ..................... A-9

Preface
This manual describes how to install, operate, and troubleshoot the VAXstation I1/GPX (Graphics Processing Extension) in the BA123 enclosure. DIGITAL recommends that you read this manual before you install your system.

If you experience system problems, use this manual to isolate the error before
seeking help from service personnel.

Description of the VAXstation 1I/GPX

The VAXstation II/GPX is a stand-alone, 32-bit workstation based on the
MicroVAX II processor. The system comes with up to 16 megabytes of memory, a video subsystem module, and an Ethernet communications module.
Other system components include a 47.5-centimeter (19-inch) diagonal color
monitor on a tilt-swivel base, a mouse or tablet, and a keyboard. You may
have one or more of the following storage options: a tape drive, diskette
drive, or fixed-disk drive.

The video subsystem, based on a VLSI (Very Large Scale Integration) graphics

coprocessor, off-loads the MicroVAX II main processor from computation-

intensive graphics tasks. The system allows parallel processing in multiple
planes so that no degradation in performance occurs as planes are added.
The 4-plane video subsystem, a 2-module set, can display 16 colors simultaneously. The 8-plane video subsystem, a 3-module set, can display 256
colors simultaneously.

The system unit and peripheral devices can be placed on the floor beside a
desk. Hardware options include printers, a tablet, a plotter, memory modules,
a video module, disk drive subsystems, a tape drive, a dual diskette drive, a
fixed-disk drive, asynchronous multiplexers, synchronous line controllers, a
programmable communications controller, and a real-time interface module.
ULTRIX-32m and MicroVMS are the two operating systems offered for the
VAXstation II/GPX. Both operating systems offer workstation software, networking software, and a wide range of tools and applications.

Workstation software expands the utility and convenience of the VAXstation II/GPX operating system by providing you with terminals simulated in

windows on the monitor screen. Each virtual terminal runs processes independently of processes running in other windows, and the keyboard may

be associated with any window at any time. Various software tools allow
you to create windows and graphics from a program level. Your workstation

software documentation contains additional information on your system and

optional hardware.

Using the mouse or the tablet to move a pointer, you can view Or manage a

variety of activities at once. For example, you can do the following:

Examine a compilation listing while editing the source file

Read notices without exiting from a program

Start one task and follow its progress while interacting with another task

Send mail without exiting an editing session

Log on to a remote VAX host to run tasks requiring intensive computation

®
~

Print a list of files on your printer while creating other files (requires the
printer option)

Conventions Used in This Document
The following conventions are used in this document:
Convention

Meaning

Bold

VAXstation 1I/GPX system controls and indicators are highlighted
in bold lettering.

“Quotes”

Diagnostic media titles and tests appear in quotations.

Italics

Computer terms defined in the Glossary are italicized the first time
the word appears in the text, beginning with Chapter 1.

Structure of This Document
The manual is divided into six parts:
Part |I: Base System Installation
This part describes how to unpack, install, and test the VAXstation II/GPX.
* Chapter 1 describes preinstallation procedures, including checking the
shipment components and ensuring adequate site preparation.

Chapter 2 describes how to set up, connect, and test the system compo-

nents.

Part II: Operation
This part describes how to operate the VAXstation II/GPX.
e

Chapter 3 describes the system controls and indicators.

Part lll: Options

This part describes the hardware options for the VAXstation II/GPX and gives

installation information where applicable.

Chapter 4 describes hard-copy output devices, input device, memory,
video devices, disk storage devices, and communications devices. The
chapter provides installation information for these options.

Part IV: Troubleshooting
This part describes how to isolate a problem and decide what to do next.
e

Chapter 5 explains basic troubleshooting procedures, power-up messages,
and the maintenance system for the VAXstation II/GPX.

Chapter 6 describes how to call DIGITAL for help.

Part V: Appendixes
*

Appendix A provides VAXstation II/GPX system specifications.

Appendix B lists related documents.

Part VI: Glossary
The glossary defines computer terms that are italicized at first use in the text
as well as other common computer terms.

Intended Audience
This manual is designed for users with little or no experience installing and
using both software and hardware.
|

Xii

Figure 1-1:

MLO-487-88

Check Your Shipment

Unpack the VAXstation II/GPX system and check your shipment against the

packing list on the outside of one of the boxes.

WAHNIN@ Because of the weight of the system unit and monitor, you need
le to perform this procedure.

Your basic shipment consists of three cartons:
1.

The VAXstation II/GPX system unit carton contains the following mate-

rials:

Accessories Kit, containing;

- Installation and testing accessories,
includiing a flat screwdriver, a
,

Phillips screwdriver, label sheets, and a grant card (for use by your

support personnel)

System unit power cord, loopback connectors, and BNE3x transceiver

cable

BC18Z video cable assembly

VAXstation II/GPX system unit (BA123 enclosure)

Hardware Support Kit (Z4A4B), containing:

VAXstation 1I/GPX Hardware Information binder, housing:
VAXstation 11/GPX Owner’s Manual, BA123 Enclosure (this manual)

VCBO02 Video Subsystem Technical Manual

For systems with TK50s or RX50s: approp a medla for ’testing and

troubleshooting (Z4A4B-C5 contains TK50 tape cartridges; Z4A4B-C3

contains RXSD diskettes.)

3. The VAXstation II/GPX consolidation carton contains the following components:

. Graphics monitor with installation documentation
®*

- ¢

Monitor power cord

LK201 keyboard with cable, feet for the keyboard, and an extra power

cord

VSXXX-AA mouse or tablet with cable

NOTE: You must order the keyboard and mouse or tablet separately from the

rest of the workstation components.

If you ordered media and documentation, you receive a soffware carton for
the operating system you selected. The MicroVMS Workstation Software carton
provides keyboard legend strips in addition to media and documentation.

1—2

VAXstation II/GPX Owner's Manual, BA123 Enclosure

The software carton also contains the “MicroVAX Dmmaatlc Monitor” used
for functional verification of software operation. It is supplied on either a
TK50 tape cartridge or an RX50 diskette as you selected, based on your
system configuration.

If additioml options are purchased at a later date, a new copy of the “MicroVAX Diagnostic Monitor” may need to be ordered.

NOTE: If you have a diskless system that contains neither a tape drive nor
a diskette drive, contact your service representative for verification of system
operation.

Check for optional items that you might have ordered, such as additional
software or a printer. Refer to the order sheet or packing list on the outside
of the cm:mns

If your shipment is damaged, or if any item is missing, inform the delivery
agent and contact your sales representative.

NOTE: Save all boxes and packing material in case you need to send back parts

of the system for repair, or if you change work locations.

Site-Preparation Review
Before installing your VAXstation II/GPX according to the instructions in the

next chapter, review thefollowing preparation requirements:
.

Adeqmte space for the system unit and peripheral devices

Proper electrical power

A suitable operating environment

You may wish to review Appendix A, which provides VAXstation II/GPX
system specifications, before you proceed with this chapter.

Space Planning
Leave sufficient space around the system unit and monitor to access the units
and to allow air circulation through the units.

The System Unit
The vents on the system unit allow proper air flow. Do not block the vents
in any way.

The unit weighs 59 kilograms (130 pounds).

Figure

1-2:

Dimensions of the System Unit
,/‘w/

62.2 cm

(24.5 in)

33cm

""/ (13n)
MLO-480-886

The Color Monitor
The vents on the monitor allow proper air flow. Do not block the vents in
any way.

1—4

VAXstation ll/GPX Owner's Manual, BA123 Enclosure

The color monitor weighs 36 kilograms (80 pounds).

Figure 1-3:

Dimensions of the Color Monitor

47 cm

(18.6 in)

54.6 an

(21.5in)

51.8cm |

A"|

o \N/

MLO-481-85

Electrical Requirements
A 20-ampere branch circuit from a power distribution panelis recommended

for each system. This circuit must meet national and local standards, provide

a good system ground, be stable, and be free from electrical noise. If power
disturbances cannot be prevented ‘add more power-conditioning equipment.
Consult service personnel to assess your needs.

The ac power source shouldsupply power to the original system and allow for

system expansion. Do not connect other equipment (such as air conditioners,
office copiers, or coffee pots) to the circuit dedicated to the system unit or
the monitor.

20~-AMP DEDICATED BRANCH CIRCUIT — 1 PHASE

POWER

CORD

DATA

CABLE

VIDEO

CABLE

|
DO NOT SHARE THE BRANCH
CIRCUIT LINES WITH OTHER
EQUIPMENT

—— |

MLO-482-85

Environment
Temperature and Humidity
The location of the VAXstation II/GPX should have an environmental control
system to maintain the recommended temperature and humidity. This system
should filter and evenly distribute air to prevent heat from accumulating.

Keep the VAXstation II/GPX away from heaters, photocopiers, or direct
sunhght

1—6

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Static Electricity

Static electricity can cause a system to fail, data to be lost, and other problems
to occur. The most common source of static electricity is the movement of
people
in contact with carpets and clothing. Low humidity causes the greatest
buildup of static electricity. The following precautions reduce static buildup:
*

Maintain greater than 40% relative humidity.

Locate the system away from busy areas, such as office corridors.

If a carpet is already fitted at the selected location, place antistatic pads
under the system.

Clean Ar@a
Dust particles can clog air passages inside the equipment, thus reducing the

cooling air flow and diskette life, especially if the particles are abrasive.
Keeping the system area clean and free from dust helps reduce those effects.

Do not pl@ce food or liquid on the system.

Supplies Stomge
Store supplies, such as diskettes, at the same temperature and humidity levels
as recommended for the system.

Preparing for Installation

1-—7

Chapter 2

ng Up the Hardware
This chapter describes how to asmmble, connect, and test the VAXstation II/
GPX. You should havealready unpacked the system as describedin Chapter
1.

CAUTION: When connecting any component of the VAXstation II/GPX system,

set all power switches to the 0 (off) position.

WARNING: Because of the weight of the system unit and monitor, you will
need two people to perform this procedure.

Make sureyow: system unit’s location meets the site-preparation requirements

in Chapter 1. To install the VAXstation II/GPX system, follow the steps as
directed in this chapter. If you have trouble:
*

Refer to Chapter 5 for troub
ubleshooting information.

Refer to Chapter 6 for service mfmmamon

The follomng section explains how to set up the color monitor.

Setting Up the Color Monitor
1.

Make sure the monitor power switch is set to 0 (off).

COLOR
MONITOR
POWER

SWITCH

MLO-600-85

2—2

VAXstation |I/GPX Owner's Manual, BA123 Enclosure

Place the monitor on a level surface. Position the monitor for ease of
use.

NOTE: Make sure the tilt-lock lever is on the right when you face the

monitor.

_TILT-LOCK LEVER

MLO-801-88

Adjust the monitor to a position you find comfortable. To tilt the monitor,
»

Slide the tilt-lock lever away from you (toward the back of the
monitor) to unlock the monitor from the base.

Tilt the monitor to the desired position.

Slide the lever toward you to lock the monitor in place.

Setting Up the Hardware

2—3

Locate the BC18Z video cable assembly from the system unit carton.
Plug the ends of the R, G, and B video cables into the corresponding

R, G, and B sockets on the back of the monitor.

clockwise to fasten.

]

Turn each connector

m"m%

BCl8Z
VIDEO
CABLE
ASSEMBLY

TO SYSTEM
MLO-502-85

2—4

VAXstation II/GPX Owner's Manual, BA123 Enclosure

Screw the video cable assembly knob clockwise into the monitor.

TO SYSTEM

MLO-503-85

Setting Up the Keyboard and Pointing Device
1.

Install the keyboard feet.
Sy

KEYBOARD FEET

KEYBOARD

(BOTTOM VIEW)

MLO-865-86

2—6

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Connect the keyboard cable to the video cable assembly.

Figure 2 1:

Keyboard Connection, Color Monitor

CABLE ASSEMBLY

Setting Up the Hardware

Locate the pointing device you wish to use, which may be either a mouse
or a tablet with a puck or stylus. Both devices cannot be used at the same
time.

4. Plug the pointing device cable into the video cable assembly.
NOTE: Attach the puck or stylus before connecting the tablet to the VAXstation

I1/GPX. The instruction sheet that comes with the tablet explains how to connect

the various components. Save this sheet for future reference. To change the puck
or stylus, first disconnect the tablet from the VAXstation I1/GPX, then swap the

puck or stylus, and reconnect the tablet to the system.

MOUSE

TABLET

TABLET PUCK

TABLET STYLUS

MLO--506A-86

2—8

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Figure 2-2: Pointing Dey ice Connection, Color Monitor

MLO-857-86

Connecting the VAXstation II/GPX to a Power

Source
1.

Make sure that all pushbuttons on the control panel of the system unit
are in the out position.

POWER

-““““”“,uwflflrf

RESTART
RUN
PUSHBUTTON —

DC OK

PUSHBUTTON

=13

HALT
PUSHBUTTON

WRITEPROTECT
PUSHBUTTON

READY
PUSHBUTTON

<«
:

MLO-509-85

Locate the labels sheet in the Accessories Kit of your shipment.
Put the appropriate label on the control panel, as shown above.

If your unit contains diskette drives, label the left drive 1 and the right

drive 2.

2—-10

VAXstation II/GPX Owner's Manual, BA123 Enclosure

en|the back door of your system unit by pulling out the left side. A

p fastemr holds the doorin place.

MLO-B11-88

Set the controls located on the CPU distribution panel insert on the back

of the system unit to the following positions:
*

Halt Enable/Disable switch to the disable position (down)

®*

Mode switch to the middle (language inquiry) position

System Unit baud rate at 4800 baud

NOTE: The panel uses international symbols rather than text.
illustration as a guide.

Use the

HALT
ENABLE/DISABLE

SWITCH

(DOWN POSITION)

| POWER-UP MODE
'SELECTION
SWITCH

BAUD RATE
SELECTION
SWITCH

MLO-512-86

2—-12

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Connect the free end of the color monitor video cable to the back of the
system unit as illustrated.
|

Figure 2—-3:

Monitor Connectio

to System Unit

TO MONITOR

L
MLO-513-86

Install and connect any uninstalled options. Option modules ordered with
your initial system order come preinstalled.

C@mnect additional devices in any order.
Read Chapter 4 for descriptions of the options and installation infor-

mation.

Also refer to the documentation included with additional devices.

Locate the monitor and system unit power cords. The two cords are the
same type and interchangeable. Ensure that the plugs fit the wall outlet.

100-120 V

\ <mmmwmmmwmmm
POWER CORD

200-250
V

MLO-B17-88

2—-14

VAXstation 1l/GPX Owner's Manual, BA123 Enclosure

10. Read and remove the 1abe1 mvemg the power connector of the system
unit.

11. Check the Vflltaga switchsetting of the system unit. If necessary, change

the switch setting to match the voltage source. To change the setting,
use a pen or screwdriver to move the switch to the correct pOSltl(m

CAUTION: An incorrect voltage switch setting will damage the VAXstation 11 /GPX system.

READ AND
|

taeL

120V (100-120 V)

VOLTAGE SWITCH

220 V (200-250 V)

MLO-618-88

2-15

12. Before you connect the VAXstation II/GPX to a power source, make
sure that the monitor power switch is set to 0 (off), the pushbuttons on

& \\

the system unit front control panel are out, and the power switch on
the system unit front control panel is set to 0 (off). The power switch
is located on the front of the VAXstation II/GPX system unit in the
following illustration.

MLO-819-85

2—-16

VAXstation II/GPX Owner's Manual, BA123 Enclosure

13. Connect the monitor power cord to the monitor first and then to an
outlet.
action to Power Source, C

11 )

TO OUTLET
MLO-B21-B6

emm«,%%

14. Plug in the ends of the system power cable.
e

Thread the cable through the system cable guide and plug one end

firmly into the system unit power connector.
*

Insert the other end of the system power cable into the wall receptacle

' TO OUTLE;\

MLO-522-88

Run the power and other cables in areas where no one will trip over them.
Avoid straining or bending the cables.
Leave the back door of the system unit open. You will be instructed to close
it in the section entitled Testing the VAXstation II/GPX in this chapter.

2—-18

VAXstation |I/GPX Owner's Manual, BA123 Enclosure

Connecting the VAXstation 1I/GPX to a Network
You can connect your workstation to either a standard or ThinWire Ethernet
network.

NOTE: For a more detailed description of networking, consult the DECconnect
System Guides.

Connecting the Ethernet Transceiver Cable to the
Workstation
To connect a transceiver cable to the VAXstation II/GPX:
1.

Set the system unit power switch to 0 (off).

Attach the BNE3x transceiver cable to the back of the system unit, routing
the cable through the cable guide slot.

CABLE GUIDE

MLO-810-86

You can connect the other end of the cable to a DELNI or DESTA or have
your service representative connect your system to an H4000 transceiver port.

Setting Up the Hardware

2—-19

Connecting to Standard Ethernet
To connect the VAXstation II/GPX to a DELNI, plug the female end of the
BNE3x cable into a free port of the DELNI.

Figure 2-5:

System Connection to a DELNI

CONNECTION
(OPTIONAL)

‘

POWER CORD
MLO-515-86

NOTE: To communicate over an Ethernet network, you must install communication software supported by your operating system.
Contact your service representative to connect your system to an H4000
transceiver port.

See Chapter 4 for more information on the DELNI and DESTA.

2—-20

VAXstation II/GPX Owner's Manual, BA123 Enclosure

Connecting to ThinWire Ethernet Using the DESTA
1.

Attach ThinWire cable to one side of the T-connector as shown in the
following illustration.

T-CONNECTOR

CONNECTOR

WLO- 78286

If the system is the first or last system in a single ThinWire segment,
attach a terminator to the side of the T-connector not connected to the
ThinWire cable as shown in the following illustration.
CONNECTOR

T-CONNECTOR

TERMINATOR

WLO-T790-88

Setting Up the Hardware

2-—-21

If the system is not the first or last system and you want to connect
another system to the ThinWire cable, do not attach a terminator to the
T-connector. Add another section of ThinWire cable to the T-connector
as shown in the following illustration.

CONNECTOR

T-CONNECTOR

CONNECTOR

MLO-784-86

/ DESTA

T-CONNECTOR

CONNECTOR

MLO--795-86

2—22

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Attach the 15-pin connector on the transceiver cable to the DESTA.
15-PIN DESTA CONNECTOR
TRANSCEIVER
CABLE

DESTA

CONNECTOR

T-CONNECTOR
MLO--796-86

Setting Up the Hardware

2—-23

Testing the VAXstation 1I/GPX
The first time you power up your system, check the various components of

your system.

If you have neither a tape drive nor a diskette drive, contact
your service representative for testing of your system. If you have either a

tape or diskette drive, follow these steps:
1.

If you have a fixed disk, push the Fixed Disk Ready pushbutton on the
control panel to put the fixed disk off-line.

TM, OPTIONAL

r/ FIXED DISKS
FIXED DISK
READY
PUSHBUTTON

MLO-628-85

Power up the monitor by setting the monitor power switch to 1 (on).

NOTE: After setting the system power switch to 1 (on), the monitor displays
the language selection menu. Ignore the data on this screen until you have
inserted the diagnostic medium as directed by this manual. If the video
display does not appear in about 30 seconds, refer to Chapter 5.
3.

Power up the VAXstation II/GPX by setting the system unit power switch

to 1 (on).

You may use either a TK50 tape drive or an RX50 diskette drive to load
diagnostics into your system. Your system can contain both types of load
devices.

2—-24

VAXstation |I/GPX Owner's Manual, BA123 Enclosure

—

If you are using a tape drive to load diagnostics, proceed to step 4. If
you are using a diskette drive to load diagnostics, proceed to step 6 (skip
steps 4 and 5).

Find the tape cartridge labeled “MVII Diag. Cust. TK50” in the cartridge
- holder at the front of this binder.

§ i

iR
S

MINI

WRITE-PROTECT
SWITCH

Bd
)

LABEL

MLO-831-85

Setting Up the Hardware

2—-25

Insert the tape cartridge into the tape drive by following these steps:

Make sure you set the system power switch to 1 (on). You cannot
move the cartridge release handle if the power switch is set to 0

(off).
b.

After the Tape Activity indicator glows green, open the tape drive
by lifting the cartridge release handle.

With the arrow on the tape cartridge facing up, insert the tape

cartridge into the tape drive.

POWER

SWITCH

TAPE ACTIVITY

INDICATOR IS

GLOWING GREEN

CARTRIDGE

RELEASE HANDLE
MLO-B32A-85

Push down the cartridge release handle.

Push in the Load/Unload pushbutton. The pushbutton glows red.
When the Tape Activity indicator glows green, the tape is ready for
use. Proceed immediately to step 8 (skip steps 6 and 7).

LOAD/UNLOAD
PUSHBUTTON
INDICATOR IS
GLOWING RED
MLO-5328-85

2—-26

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

CAUTION: Do not lift the cartridge release handle until the Load/

Unload pushbutton extinguishes and the Tape Activity indicator glows
green. Do not lift the cartridge release handle while an indicator light
flashes.

NOTE: For a more detailed discussion of the TK50 tape drive controls and

procedures, refer to Chapter 3.

Find the diskettes labeled “MVII Diag. Cust. RX50” in the diskette holder
at the front of this binder.

softare
MVII DIAG. CUST. RX50

Digrtat € quipment Corporation

WRITE-PROTECT NOTCH

MLO-529-8

Setting Up the Hardware

2-27

Insert the diagnostic diskette labeled “#1” by following these steps:
a.

Open drive 1. The diskette drives contain a cardboard shipping card.

Remove the cardboard card prior to diskette insertion.
b.

Aligning the orange arrow on the diskette with the orange stripe on
the drive, insert the diskette.

Close drive 1.

MLO-830-86

The language selection menu display appears on the monitor screen
automatically.

2—28

VAXstation II/GPX Owner's Manual, BA123 Enclosure

From the language selection menu displayed on the monitor, select the
language to match your keyboard by pressing the corresponding number
key and then pressing RETURN.

KA630-A.V1.2

1) Dansk

7) Nederlands

2)
3)
4)
5)
6)

8)
9)
10)
11)

Deutsch
English
Espafiol
Frangais
Italiano

Norsk
Portugués
Suomi
Svenska

(1..11):

MLO-833-85

If you select English, French, or German, a second menu appears. Select
which variant of the language you prefer. For example, if you select

English, you have the following choices:
®

United Kingdom

United States/Canada

The monitor slowly displays the numbers 7 through 3, indicating completion of steps in the power-up test.
The last part of the display contains the numbers 2 through 0, indicating

that the system is loading “MicroVAX Maintenance System” software.
Performing normal system tests.

7..6..5..4..3..
Tests completed.
Loading system software.
2..1..0

NOTE: If you neglected to or took too much time to insert the diagnostic
medium, the monitor displays a “?54 retry” error message.
Insert the
diagnostic medium into the load device (if you have not already done so) and
press the Restart pushbutton to reboot the system.

Setting Up the Hardware

2—29

After the power-up test finishes, the introductory display of the “MicroVAX
Diagnostic Monitor” appears.
MicroVAX Diagnostic Monitor

CONFIDENTIAL DIAGNOSTIC SOFTWARE
PROPERTY OF

DIGITAL EQUIPMENT CORPORATION
Use Authorized Only Pursuant to a Valid Right-to-Use License

Current date and time is:

25-Jun-1987 12:30:10

Press the RETURN key to continue

OR enter new date and time,

then press the RETURN key.

[DD-MMM-YYYY HH:MM]:
9.

Make sure the date and time in the introductory display are accurate. If
the date and time are accurate, press RETURN.

If the date and time are inaccurate or not known, type the correct date

and time, following the format as shown.
12:30:10. Press RETURN.

An example is 25-JUN-1987

The test preparation display informs you that the system is preparing for
testing. This process takes a few minutes.
If you have an RX50 diskette drive, text instructs you to remove the

diskette labeled “#1” and insert the diskette labeled “#2”. The system
informs you if additional diskettes are required to complete testing.

NOTE: If your system does not prompt you for all the diskettes in the
diagnostics package, your system configuration does not require the additional
diskettes for testing.

2—-30

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

10. When the diagnostics are loaded, text tells you to remove the diskette or
tape cartridge and to press RETURN.
The monitor displays the “Diagnostic Monitor Main Menu”.

describes each of the options.

Chapter 5

NOTE: Do not select a menu choice until this manual directs you to.
MAIN MENU

1 - Test the system

2 - Show System Configuration and Devices
3 - Display the System Utilities Menu
4 - Display the Service Menu

5 - Exit MicroVAX Diagnostic Monitor
Type the number:

then press the RETURN key.

Setting Up the Hardware

2—31

11. Turn the Mode switch counterclockwise on the back of the system unit
to the next position to save the language you selected in step 8. Close

the back door of the system unit.

G
POWER-UP
MODE —
SELECTION
SWITCH

Baud

MLO-B37-85

2—-32

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

12. Select the “System Test” diagnostic by typing 1 and then pressing RETURN. These diagnostics check the system components.
A few moments later, the monitor displays the “System Test” screen.
MAIN MENU

SYSTEM TEST
This is a test of the MicroVAX computer and its devices.
No additional preparation for this testing is required;

the MicroVAX is ready to be tested.
Testing occurs in two parts:

The functional tests quickly

test each device sequentially; the exerciser test (lasting
about 4 minutes) tests how the devices work together.
To halt the test at any time and return to the Main Menu,
type CTRL-C by holding down the CTRL key and pressing the C key.
Press the RETURN key to begin testing,

OR type O and press the RETURN key to return to the Main Menu.

Setting Up the Hardware

2—-33

13. Press RETURN to begin testing.
The monitor displays several messages to inform you of the progress of
the system tests, then the following color bar display appears:

BLACK

BLUE

RED

MAGENTA | GREEN

CYAN

YELLOW

WHITE

MLO-B3BA-B5

After about 4 minutes, a message telling you the system has passed the
testing appears on your screen.
SYSTEM TEST PASSED
All devices passed functional tests and the system passed
the exerciser test.

At this point you may exit from the MicroVAX Diagnostic

Monitor or perform more specialized testing.
like additional information,

If you would

consult the system

documentation.

Press the RETURN key to return
to the previous menu.

2—-34

VAXstation 1l/GPX Owner's Manual, BA123 Enclosure

You have successfully installed and tested your VAXstation II/GPX system.
NOTE: If you see error messages, refer to the troubleshooting section of
Chapter 5.
14. Press RETURN to get back to the “Main Menu”. The “Main Menu” shown
in step 8 is displayed. Chapter 5 describes the diagnostic tests.
15. Type 5 and press RETURN to exit. The monitor displays the following:
Exiting MicroVAX Diagnostic Monitor
Exit complete.

You may now load your system software.

16. If you have a fixed disk, push the Fixed Disk Ready pushbutton on the

control panel to put the fixed disk back on-line.
To rewind and unload the TK50 tape cartridge from the tape drive, press

the Load/Unload pushbutton to the out position.

When the procedure is

complete, the Load/Unload pushbutton stops glowing and the Tape Activity
indicator glows green. Pull out the cartridge release handle, remove the
tape cartridge, and push in the cartridge release handle. See Chapter 3 for
more details on this procedure.
You are now ready for software installation. If you are unfamiliar with the

system controls and indicators, read Chapter 3, which covers system operation, before installing the software. After you have installed the software,
read the rest of this manual.

Setting Up the Hardware

2—35

Chapter 3

VA Xstation 11/GPX Hardware
This chapter contains information on the following topics:
e

VAXstation II/GPX controls and indicators

Turning on the VAXstation II/GPX

Turning off the VAXstation II/GPX

Color monitor controls and indicators

Fixed disk drive

Tape drive and tapes

Dual diskette drive and diskettes

Back-up copies

VAXstation 1I/GPX Controls and Indicators
The front control panel (Figure 3-1) contains the following controls and
indicators:

System power switch

Restart/Run momentary-contact pushbutton

e
e

DC OK indicator
Halt pushbutton

Fixed Disk Write-protect pushbutton
e

Fixed Disk Ready pushbutton

VAXstation 1I/GPX Hardware

3-—1

Figure 3—1:

Controls and Indicators

POWER
SWITCH

—
VAXstation

I/GPX

RESTART/RUN
PUSHBUTTON
—__
DC OK
g
PUSHBUTTON
o1

HALT

WRITE-PROTECT

READY
PUSHBUTTON

PUSHBUTTON

MLO-642-85

Additional controls and indicators are located on the CPU distribution panel
on the back of the VAXstation II/GPX system unit.

3—2

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Figure 3-2: The CPU Distribution Panel
HALTS ENABLED

HALT ENABLE/DISABLE
SWITCH ICON

HALT
TM | |l| —
E/DISABLE
ENABL

o
' "

POWER-UP MODE .
SELECTION SWITCH

2aof

HALTS DISABLED

(eo

|~ DISPLAY

‘
' / _ NORMAL OPERAT
ION
D

E
GE INQTUIRMODY MOD
LANGUA
/ __
]/
E
__—~ LOOPBACK TES
O

BAUD RATE
SELECTION

SWITCH

PRINTER

_~” PORT

MLO-807-86

The switches, indicator, and connector on the CPU distribution panel provide
the following functions:

Halt Enable/Disable Switch (2-position toggle switch)
Switch Position

Function

Up (dot inside circle)

Halts are enabled. On power-up or restart, the system
will enter console I/O mode at the completion of startup diagnostics.

Down (dot outside circle)

Halts are disabled. On power-up or restart, the system will attempt to load software from one of the boot
devices at the completion of start-up diagnostics.

VAXstation II/GPX Hardware

3—3

Power-Up Mode Selection (3-position rotary switch)
Switch Position

Arrow

Mode

Run.

If the system supports the Multinational Character Set

(MCS), the user will be prompted for language only if the battery

backup has failed. Full start-up diagnostics are run.
Face

Language inquiry (factory setting). If the system supports MCS,
the user will be prompted for language on every power-up and
restart. Full start-up diagnostics are run.

T in a Circle

Test. ROM programs run wraparound serial-line unit (SLU) tests.

Baud Rate Selection Switch (8-position rotary switch)
This switch sets the baud rate of the console terminal serial-line. The factory
The baud rate of this switch must match that of the
printer, if present.
setting is 4800 baud.

Light-Emitting Diode (LED) Display
This indicator displays numbers of on-going steps of power-up tests and booting procedures. If a failure occurs, the display indicates the field replaceable

unit (FRU) that is the most probable cause of the failure. Refer to Chapter
5, under the section titled Power-Up Messages, for a brief description of the

hexadecimal numbers.

Printer Port
This is a 9-pin connector for a cable to a printer.

The System Power Switch
POWER
SWITCH

dlifglit]all
VAXstation
I/GPX

y
MLO-643-85

3—4

VAXstation |I/GPX Owner's Manual, BA123 Enclosure

The system power switch controls the ac power. Setting the switch to 1
turns on the power. Setting the power switch to 0 turns off the power.

The Restart/Run Pushbutton

Restart/

Run

MLO-544-85

The Restart/Run momentary-contact pushbutton reboots the operating system software when pushed. Work in progress is lost.
When the system is on, the Restart/Run pushbutton glows green to indicate
normal software operation. If the pushbutton does not glow, refer to Chapter
5 for troubleshooting information.

The DC OK Indicator

DC OK

MLO-545-85

The DC OK indicator glows green when the system is generating power. If
the indicator does not glow, the system is not generating power. Refer to
Chapter 5 for troubleshooting suggestions.

VAXstation Il/GPX Hardware

3—5

The Halt Pushbutton

® | Halt

MLO-546-85

The Halt pushbutton stops the program currently running without shutting
down the VAXstation II/GPX.
When the Halt pushbutton is pressed, it latches in and glows orange.

The

Halt pushbutton should be set in the out position and not glowing to allow

for software operation.
The Halt Enable/Disable switch (on the back of the VAXstation II/GPX

cabinet) is normally set to the disable position (up) to prevent the system
from going into console mode when you execute a halt in a program. The
disable position also stops devices (such as a printer) connected to the auxiliary
port from halting the processor.
To get into console mode, shut down any software that may be executing and
put the Halt Enable/Disable switch (located on the back of the system unit)

in the enable position (down). Then, press the Halt pushbutton twice. Any
data not saved before pressing the pushbutton will be lost. The MicroVAX
II Maintenance Manual describes the console commands. You can also enter
console mode from the workstation software. Consult your system software
documentation.

3—6

VAXstation |I/GPX Owner's Manual, BA123 Enclosure

HALT

' ENABLE/DISABLE

SWITCH

(UP POSITION)

MLO-546A-85

VAXstation II/GPX Hardware

3—7

The Fixed Disk Pushbuttons

WriteProtect

® | Ready

MLO-547-85

Your system may contain one or more fixed disks with external pushbuttons.

If your system does not have a fixed disk, these pushbuttons are inoperable.

The Fixed Disk Write-Protect pushbutton is set in the out position and not
System software can read or write
information on the disk. To write protect the disk, preventing system software
from erasing or writing on the disk, push in the Write-Protect pushbutton.
The pushbutton glows orange.
glowing for normal software operation.

The Fixed Disk Ready pushbutton glows green when it is set to the out

position and indicates that the fixed disk is ready to store information. When
pushed in, the pushbutton stops glowing, and the fixed disk is disabled. In
effect, the fixed disk is turned off.

Turning On the System
This procedure assumes that the system has been installed according to the
installation instructions in this manual and that the system software has been
installed. If the system software has not been installed, consult the software

documentation and install the software.

3—8

VAXstation |I/GPX Owner's Manual, BA123 Enclosure

Initial Control Panel Switch Settings
1.

If you have a fixed disk, set the Fixed Disk Ready pushbutton to the
out (ready) position.

Set the monitor power switch to 1 (on).

Set the system power switch to 1 (on).

When you turn on the power, the VAXstation II/GPX control panel indicators
appear as described in Table 3-1.

Table 3—1:

Normal Power-On Indications

Control/Indicator

Normal Indication

Restart/Run

Glows green

DC OK

Glows green

Halt

Not glowing

Fixed Disk Write Protect:

Not glowing

Fixed Disk Ready:

Glows green within 30 seconds

Tape Drive Load/Unload:

Glows red for 4 seconds and then stops glowing

Monitor Power Indicator:

Glows green

If you do not observe the indications listed in Table 3-1, refer to Chapter 5
for troubleshooting information.
The monitor displays the power-up screen.
Performing normal system tests.
7..6..5..4..3..

Tests completed.
Loading system software.

2..1..0

The monitor slowly displays the numbers 7 through 3, indicating completion

of steps in the power-up system test.

The VAXstation II/GPX performs

power-on system tests each time you turn on the system.

Then, the monitor displays the numbers 2 through 0 to indicate that the
The first screen

VAXstation II/GPX system is loading the system software.

for the system software appears on the monitor after a few seconds.

VAXstation Il/GPX Hardware

3—9

The VAXstation II/GPX system is now ready for use.

Refer to the system

software documentation for instructions on using the VAXstation II/GPX
system.

Turning Off the System
To prevent loss of data and to ensure an orderly system shutdown, follow

the system shut-down procedure described in your system software documentation.

Turn off the VAXstation II/GPX system by setting the power switch to 0

(off).
CAUTION: Before moving the monitor, turn it off and wait 30 seconds to allow
static electricity on the CRT to discharge.

Color Monitor Controls and Indicators
The front and side of the monitor have the following six controls and

~indicators:
The contrast control lets you adjust the video display.
The brightness control allows you to adjust the video raster (background

intensity) to compensate for ambient light in the room. To adjust the raster,
set the brightness control to minimum.

Slowly turn up the control until

horizontal lines appear on the screen, then reduce the brightness until the

lines disappear.

The degauss switch lets you clear picture distortion caused by external
Press the degauss switch after any movement of the monitor

interference.

to correct color distortions. If you need to press the degauss switch a second
time, first wait 10 minutes to allow the circuit to reactivate.

The power switch enables you to turn on or off the monitor. Press 1 to turn
on the power. Press 0 to turn off the power.
The tilt-lock lever enables you to adjust the angle of the monitor. Set the

tilt-lock lever back to adjust the tilt. Pull the lever forward to the original
position to lock the monitor at the desired angle. The lock prevents the tilting
mechanism from moving the monitor. You can swivel the monitor on the
base, and the angle will be maintained.

3—-10

VAXstation 1I/GPX Owner's Manual, BA123 Enclosure

The power indicator glows to indicate that power is applied to the monitor.

Figure 3-3:

Front and Side Controls, Color Monitor

CONTRAST
BRIGHTNESS
DEGAUSS

POWER ON/OFF

\TILT-LOCK LEVER
POWER

INDICATOR

FRONT VIEW

MLO-550-85

VAXstation Il/GPX Hardware

3—11

The back of the monitor has the following six connectors and controls:
The end of the R, G, and B video cables plug into the R, G, and B sockets.
The monitor, keyboard, and pointing device are joined to the system unit
through the video cable assembly, which screws into the cable assembly
mounting hole.
The fuse protects the monitor from electrical damage.

The monitor power cord plugs into the power cord connector.

Figure 3—4:

Rear Controls and Connectors, Color Monitor

G
SOCKET
B
SOCKET

CABLE ASSEMBLY
MOUNTING HOLE

FUSE

POWER CORD
CONNECTOR

REAR VIEW

3-12

VAXstation II/GPX Owner's Manual, BA123 Enclosure

MLO-562-86

Fixed Disk Drive
The fixed disk drive, located inside the cabinet, stores information on a
nonremovable disk.
The RD53 fixed disk stores up to 71 megabytes of data. The RD54 fixed disk
stores up to 159 megabytes of data. Fixed disk systems are usually configured
to include the TK50 tape drive for removable storage of data.

FIXED DISK
DRIVE

MLO-488-86

Tape Drive
The TK50 tape drive holds one removable TK50 magnetic tape cartridge. The
information is magnetically stored on one side of a TK50 tape. Information

can be erased, and new information stored in its place. Each tape cartridge
holds 94.5 megabytes of information.
The tape cartridge can be used as both an input and output device. As an

input device, it can be used to load software or data into the system. As an
output device, the cartridge can be used to make copies (backups) of software
or data on the tape cartridge media.
The tape drive has two primary controls: the cartridge release handle and
the Load/Unload pushbutton.

The cartridge release handle is used to

insert or remove cartridges and lock them into position. The Load/Unload

pushbutton controls winding and rewinding of the tape. The pushbutton is
a 2-position control; when the pushbutton is first pressed in, the tape winds

VAXstation II/GPX Hardware

3—13

onto the take-up reel inside the drive. When pressed again, the pushbutton
pops out and winds the tape back into the tape cartridge.

TK50 CARTRIDGE
RELEASE HANDLE
TK50 LOAD/UNLOAD
PUSHBUTTON INDICATOR

\ TK50 TAPE ACTIVITY
INDICATOR

Inserting a Tape Cartridge
Make sure the system power switch is set to 1 (on) and the Load/Unload
pushbutton is not glowing.

The Load/Unload pushbutton glows red for

approximately 4 seconds during the tape drive power-on self test.
The
pushbutton stops glowing, and the Tape Activity indicator glows green to
show that you can begin the following procedure.
1.

Pull out the cartridge release handle.

With the arrow on the tape cartridge pointing toward the cartridge release

handle, insert the cartridge into the drive.

The Load/Unload pushbutton glows red.

The Tape Activity indicator stops glowing.

Push in the cartridge release handle to lock the tape in the operating
position.

The Load/Unload pushbutton stops glowing.

The Tape Activity indicator glows green.

3—-14

VAXstation II/GPX Owner's Manual, BA123 Enclosure

Press in the Load/Unload pushbutton.
e

The Load/Unload pushbutton glows red.

The Tape Activity indicator stops glowing.

The tape is loaded in 10-15 seconds. If a tape is new, the system performs a
calibration sequence that takes approximately 40 seconds. The Tape Activity
indicator flashes green rapidly and irregularly during calibration.
During loading, the Load/Unload pushbutton glows red.

When the Tape

Activity indicator glows green, the tape is ready to use.

TAPE ACTIVITY
INDICATOR 1S
GLOWING GREEN

CARTRIDGE
RELEASE HANDLE

LOAD/UNLOAD
PUSHBUTTON
INDICATOR IS
GLOWING RED
MLO-859-85

CAUTION: Keep the cartridge release handle down when the Load /Unload
pushbutton glows red. Make sure the Tape Activity indicator glows green before
lifting the cartridge release handle.

VAXstation Il/GPX Hardware

3—15

CAUTION: If the Load/Unload pushbutton flashes red rapidly at any time,
press it four times. If the problem persists, do not attempt to use the tape drive
or to remove the tape cartridge. Call your service representative.

Rewinding and Unloading a Tape Cartridge
Rewind and unload a tape before removing it from the tape drive.
1.

Press the Load/Unload pushbutton to the out position.
*

The Load/Unload pushbutton and Tape Activity indicators flash
slowly, but not in unison, as the tape rewinds to the beginning
(unless the tape was already at the beginning).

The Load/Unload pushbutton glows red, and the Tape Activity
indicator stops glowing as the tape unloads into the cartridge.

When the procedure completes, the Load/Unload pushbutton stops
glowing and the Tape Activity indicator glows green.

Pull out the cartridge release handle.
Remove the tape cartridge and store it in a safe place.

Push in the cartridge release handle. The Tape Activity indicator glows
green, showing that power is supplied to the drive.

NOTE: Rewinding a tape can also be done under software control. Refer to your
software documentation for information.

3-16

VAXstation II/GPX Owner's Manual, BA123 Enclosure

Table 3g—-2:

Tape Drive Controls and Indicators

Control

Position

Condition

Load/Unload
Pushbutton

Slowly flashing. Tape is loading (10-15 seconds).
Rewinding and loading can take up to 2
minutes.

Out

Tape Activity

Load/Unload
Pushbutton

Tape is rewinding and unloading.

Indicator

Condition

Off

No power to the tape drive.

Off

Safe to lift cartridge release handle to insert

or remove a tape. Power is present.

Unsafe to lift the cartridge release handle.
®

Power-on self test is occurring—glows
for only 4 seconds.

(Cartridge is inserted but handle is still
up.

Tape is loading or unloading.

Tape is stopped.

Tape loaded successfully.

Flashing

Tape is in motion (except rewind). Read/
write commands are being processed. Irregular fast flashing means tape calibration is
occurring.

Tape is rewinding.

Flashing

Flashing rapidly =~ A fault is occurring. Press and release the

Load/Unload pushbutton four times. If the
problem persists, do not attempt to use the
tape drive or to remove the tape cartridge.
Call your service representative.

lif a tape is new, the system performs a calibration sequence that takes approximately 40 seconds.

VAXstation Il/GPX Hardware

3-17

Table 3-2 (Cont.):

Tape Drive Controls and Indicators

Handle

Position

Function

Cartridge
Release
Handle

Out

Allows a tape to be inserted or removed after rewind and unload operations are completed.

Locks tape in operating position.

Protecting Tape Cartridges from Accidental Overwriting
The TK50 tape cartridge has a write-protect feature to prevent loss of data
by accidental overwriting. To write-protect the tape, slide the write-protect
switch toward the tape label slot.

TAPE CARTRIDGE

WRITE-PROTECT
SWITCH
NOT WRITEPROTECTED

WRITEPROTECTED
MLO-858-86

NOTE: The system can read information on the tape, regardless of the position
of the write-protect switch. However, the system cannot write data to the tape
when the switch is set to the write-protect position.

3-18

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Handling and Storing Tape Cartridges

Follow th;ese guidelines when handling and storing TK50 tape cartridges:
e

Do not touch the exposed surface of the tape.

Do not throw or drop the tape cartridge.

Store tape cartridges in a dust-free environment.

Do not apply adhesive labels to the top, bottom, or sides of a cartridge.
Place labels only in the label slot on the front of the tape cartridge.

Write on the identification label before inserting it in the label slot on the
front of the cartridge.

Allow new blank and prerecorded tapes to stabilize at room temperature
for 24 hours before using them.

Keep tape cartridges away from direct sunlight, heaters, and other sources
of heat. Store tape cartridges in a stable temperature between 10 and 40
degrees Celsius (50 and 104 degrees Fahrenheit).

Keep tape cartridges away from magnets and equipment such as motors,
transformers, terminals, monitors, and audio equipment, that generate
magnetic fields.

Keep tapes away from x-ray equipment.

Dual Diskette Drive
The RX50 dual diskette drive holds up to two 13.13-centimeter (5.25-inch)
diskettes. Each diskette stores 400 kilobytes of information, which is roughly
150 typewritten pages.

Close the drive door when using a diskette. The drive does not work with
the door open.

VAXstation II/GPX Hardware

3—19

A Diskette Activity indicator on each drive glows red when a drive is in

use. Keep the drive doors closed when the Diskette Activity indicators are

glowing red. Opening the doors could erase data or delete information.

|| DISKETTE ACTIVITY
Ly INDICATORS

MLO-B53-88

The information on RX50 diskettes is magnetically stored on one side of the
diskette. Stored information can be erased, and new information stored in its

place.

3—20

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

The diskette, permanently enclosed in a cover, rotates inside the cover. The
soft fabric lining of the cover continuously cleans the diskette.

NOTE: Use only formatted RX50 diskettes, available from DIGITAL or DIGI-

TAL'’s licensed distributors.

DISKETTE
LABEL

DISKETTE

g~ WRITE-PROTECT

NOTCH

CQVER

. DISKETTE

SURFACE
DO NOT
ORANGE

TOUCH

ARROW

PROTECTIVE

ENVELOPE

]

MLO-564-85

VAXstation II/GPX Hardware

3—21

Inserting a Diskette
Keep the diskette drive door closed while a Diskette Activity indicator is

glowing red.

Opening the door might damage the drive heads.

Wait for

the indicator to stop glowing, which indicates that diskette drive activity has

finished.
a.

Open the drive door by pressing on the door’s outer edge.

Align the orange arrow on the diskette cover with the orange stripe on
the drive and insert the diskette.

The write-protect notch is down for

drive 1 and up for drive 2.

After inserting the diskette, press the drive door closed.
excessive force; the door should close easily.

MLO-556-86

3—22 VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Do not use

Protecting Diskettes from Accidental Overwriting
The RX50 diskette has a write-protect feature to prevent loss of data from

accidental overwriting. To protect the data, cover the write-protect notch on

the side of the cover with a self-adhesive foil tab supplied with your diskettes.
Remove the tab when you want to add, change, or delete information.

) wRiTE-

PROTECT
TAB

MLO-5566-85

Handling and Storing Diskettes
Incorrect handling and storing of diskettes can damage them (and the RX50
recording head) and cause loss of data. The following precautions should be
taken:
®

To keep out dust and dirt, put the diskette in its envelope when the
diskette is not in use.

Do not fold or bend the diskette cover.

Do not touch the recording surface of the diskette. When out of its
envelope, handle only the top (label area) of the diskette.

Store the diskette vertically (with the label at the top) and loosely to
prevent the cover from becoming warped.

®*

Write on the label before applying it to the diskette cover to avoid creasing
the cover. If you need to change the label, use a felt-tipped pen.

Store the diskette away from direct sunlight and heaters.

Store the diskette away from strong magnetic fields and steel objects.
Magnetic fields (produced by motors, transformers, and terminals) can
erase data.

VAXstation II/GPX Hardware

3—23

Back-up Copies
A back-up copy is a copy of files stored on the VAXstation II/GPX fixed disk,

diskette, or tape. Making back-up copies of files ensures a copy for you in
case information is accidentally lost. As a general rule:
*

Make back-up copies on diskettes or magnetic tape.

®*

Make a daily back-up copy of information you create or change that day.

Make a weekly back-up copy of information stored on your fixed disk
drive.

Store back-up copies in a safe place.

Make back-up copies of system software files as described in the system
software documentation.

3—24

VAXstation II/GPX Owner's Manual, BA123 Enclosure

Chapter 4

Options
The options currently supported by the VAXstation II/GPX are divided into
six categories and consist of the following:

Hard-copy Output Devices—Printers and Plotter (LN03, LN03 PLUS,
LAS50, LA75, LA210, LPS40, LCGO01, and LVP16)

Input Devices—Tablet (VSXXB-AB), Mouse (VSXXA-AA)

Memory—Memory Modules (MS630-BA, MS630-BB, MS630-CA)

Video—4-Plane (M7168) Module

Storage Devices—Fixed Disk Drives (RD53 and RD54), Tape Drive (TK50),
and Dual Diskette Drives (RX50)

Communications—Ethernet communication module (DEQNA), ThinWire
Ethernet connectors and terminators, the DIGITAL ThinWire Ethernet Station Adapter (DESTA), Asynchronous Multiplexers (DZQ11 and DHV11),
Synchronous Line Controllers (DMV11 and DPV11), Programmable Controller (KMV11), and Modems (DF03, DF112, DF124, and DF224).

This chapter describes each option and directs you to the appropriate installation instructions. You may install a printer, the tablet, and the color monitor

yourself. However, contact your service representative to install all the other
options.

The VAXstation II/GPX is also upgradeable to a 2-user ULTRIX system having
two monitors, two keyboards, two input devices, and two VCB02 graphics

modules. Contact your sales representative for information on this upgrade.

CAUTION: If you attempt to install the memory modules, video module, disk
drive subsystems, tape drive, dual diskette drive, communications module, asynchronous multiplexers, synchronous line controllers, or programmable controller,
you might damage the system.

Options

4—1

To order an option after initial system installation, contact your sales rep-

resentative. For more information on those options, refer to the documents

listed at the end of each section! and the VAXstation 11/GPX Maintenance
Manual.

Hard-Copy Output Devices
The VAXstation II/GPX can be used with seven printers: the LN03, the LN03
PLUS, the LPS40, the LA210, the LA75, the LA50, and the LCGO01. The
VAXstation II/GPX can also be used with the LVP16 plotter. Each of the
following sections describes one of these options. The final section explains
how to connect a printer or plotter to a VAXstation II/GPX.

Printers
The LNO3

The LNO3 laser printer is a desk-top, nonimpact printer that produces letterquality text at 8 pages/minute. For systems running MicroVMS, the printer
can also display graphics.

The LNO03 offers 16 fonts, including Courier, Elite, and the VT100LineDrawing Set (the DIGITAL standard set), ASCII multinational technical character sets and 12 national language character sets can also be used.
The printer comes with three character sets. If you want to mix type styles and
point sizes, the LN03 can print up to 24 fonts/page. To expand memory or
add additional fonts, you can purchase more programmable RAM or precoded
ROM cartridges from DIGITAL.

The LNO3 uses only cut sheet paper. A paper cassette holds 250 sheets
of paper. The printer automatically collates output for you in its facedown output tray. The LNO03 can also handle preprinted single-part forms,
transparencies, and labels. The LN03 can print in either landscape (horizontal)
or portrait (vertical) mode.

CAUTION: When the LNO3 or LNO3 PLUS is connected to an operating VAXstation I1/GPX, make sure the Halt Enable/Disable switch is disabled before
powering on and off the system. Otherwise, you cause the irretrievable loss of
data.

1 These documents pertain only to customers in the United States. If you are not a U.S. customer or if you
require translated documents, check the appropriate country’s product listing.

4-—-2

VAXstation |I/GPX Owner's Manual, BA123 Enclosure

The LNO3 weighs 28 kilograms (66 pounds).

Figure 4-1:

The LNO3

33cm

(13 in)

MLO-B62-86

To order an LNO3 printer after the initial system installation, contact your sales
representative. You can install the LNO3 printer yourself. After assembling

the printer, see the section Printer and Plotter Connection to the System.

For more information about the LN03 printer, see the following documents:

Installing and Using the LNO3 (Order No. EK-0LN03-UG-001)

LNO3 Programmer Reference Manual (Order No. EK-0LN03-RM-001)

LNO3 Maintenance Kit Guide (Order No. EK-LN03U-MG-001)

LNO3 Toner Kit Guide (Order No. EK-0LN03-MG-001)

The LNO3 PLUS
The LNO3 PLUS is the upgrade configuration of the LNO3 laser printer. The
LNO3 PLUS system consists of a base LN03 laser printer and an LN03S
bitmap option module. The LN03 PLUS requires the firmware microcode
V4.4 to be installed in the base LNO3 printer.

Options

4-—3

The LN03 PLUS enhances the ability of the LNO3 printer to print documents
composed of text and graphics. The LN03 PLUS enables you to process

ANSI and Tektronix data files with any ratio of text to graphics and with no
limits on image complexity.

The LNO03S bitmap option module consists of a printed circuit board that
is inserted into the available option slot of the LNO03 printer. This option
modaule’s key featureis an on-board memory capacity of one Mbyte of dynamic
RAM used for bitmap storage. The LN03S option module also contains up
to 128 Kbytes of ROM for program and font storage.
The printer and host system communicate through the standard RS232-C
serial interface.

All setup features in the LN03 PLUS are the same as in the base LN03 and
are controlled through the default setting of configuration switches or under
program control.

CAUTION: When the LN03 or LN03 PLUS is connected to an operating VAXstation 11/GPX, make sure the Halt Enable/Disable switch is disabled before
powering on and off the system. Otherwise, you cause the irretrievable loss of
data.

To order an LN03 PLUS printer or an LN03S option module for installation
into an existing LNO3 printer, contact your sales representative.

The PrintServer 40 (LPS40)

The PnntServer 40 is a MicroVAX II-based laser printer containing POST-

SCRIPT® software. The PrintServer 40 is designed as an Ethernet node in
order to serve many users.

A dedicated MicroVAX II-based data controller interprets applications programs
that output in POSTSCRIPT, a powerful industry-standard page description
language. The PrmtServer 40 supports existing software, using ANSI text/

sixels, ReGIS, or Tektronix® 4010/4014 format through the use of host-based
translators.

The PrintServer 40 prints monochromatically at a rate of 40 pages per minute
at a resolution of 750 x 750 dots per centimeter (300 x 300 dots per inch).
Paper sizes include letter, legal, and ledger, and A4, A5, B4, and BS metric
sizes. A large capacity input tray holds 2000 sheets of cut sheet paper and
two auxiliary trays hold 250 sheets each.

The PrintServer 40 contains a library of 29 typefaces that may be scaled to
any point size, rotated to any degree, and positioned anywhere on a page,
through the use of POSTSCRIPT commands.

4-4

VAXstation II/GPX Owner's Manual, BA123 Enclosure

Specifications for the PrintServer 40:

Size: 102.62 cm (40.4 in) high x 72.14 cm (28.4 in) deep x 152.4 cm (60
in) wide

Weight: 219.99 kilograms (484 Ib)

Voltage:
*

200/208/240 V, 60 Hz

200/220/230/240 V, 50 Hz

Figure 4—2:

The PrintServer 40 (LPS40)

Options

4-5

The LA210

The LA210 is a dot-matrix desk-top printer that can produce high-speed drafts
(240 characters/second) or near letter-quality correspondence (40 characters/
second). With the addition of an optional font cartridge, the LA210 can print
memo-quality correspondence (80 characters/second). The LA210 also prints
bitmap graphics.

The printer can print in USASCII, 10 national languages in Courier 10,

and the VT100 line-drawing set (the DIGITAL standard set). Other features
include three optional typefaces: Gothic, Orator, and Italic. Over 30 optional
character sets, including symbols and technical characters, can be added by
plug-in font cartridges. You can select up to eight character widths.
The LA210 prints on single-sheet and fanfold paper and handles forms with
up to four parts. The printer’s carriage accommodates paper ranging in width
from 8.9 centimeters (3.5 inches) to 37.8 centimeters (14.9 inches).
The printer weighs 11.3 kilograms (25 pounds).

Figure 4—-3:

The LA210

54.6 cm |
(21.5 in)

(13.5 in)
MLO-661-86

To order an LA210 printer after the initial system installation, contact your
sales representative.
You can install the LA210 printer yourself.
After
assembling the printer, see the section Printer and Plotter Connection to the
System.

4—-6

VAXstation II/GPX Owner's Manual, BA123 Enclosure

For more information about the LA210 printer, see the following documents:
®

Installing the LA210 Letterprinter (Order No. EK-LA210-IN-001)

[LA210 Letterprinter User Guide (Order No. EK-LA210-UG-001)

LA210 Letterprinter Programmer Reference Manual (Order No. EK-LA210RM-001)

LA210 Letterprinter Operator and Programmer Reference Guide (Order No.
EK-LA210-RC-001)

LA210 Letterprinter Emulation Modes Reference Guide (Order No.
LA210-RG-001)

EK-

The LA75
The LA75 is a desk-top dot-matrix printer that can produce sixel-protocol
bitmap graphics.

The LA75 prints in draft speed (250 characters/second),
memo speed (125 characters/second), and letter-quality speed (32 characters/second). The printer offers optional font cartridges and international
character sets. You can use office stationery or fanfold paper.
The LA75 is compatible with DIGITAL’s LA50 and LA210 printers as well as

IBM’s PRO printer. The LA75 uses the DEC423 serial interface.
The LA75 weighs 10 kilograms (22 pounds).

Options

4-—7

Figure 4—4:

The LA75

f«x“

“’

§
oy

’/
"y

vu‘,'n,»

.hvwww

’« $

w"”

‘(‘

,«
,N
uw
.w
m,
,n
‘m

“:

42.7 cm

{16.8 in})

%
o

(13.6 in)

."“‘J ‘

MLO-788-86

To connect the LA75 printer to your VAXstation II/GPX you need an adapter,
the H8571-B and a cable, either the BC16E-10 (30.48 meters/10 feet), BC16E25 (76.2 meters/25 feet), or the BC16E-50 (152.4 meters/50 feet).
To order an LA75 printer and the necessary cable and adapter after the initial
system installation, contact your sales representative.
The LA5S0

The LA50 is a desk-top dot-matrix printer that can produce bit-map or
character cell graphics.

The LA50 prints in draft speed (100 characters/second) and memo speed (50
characters/second). The printer offers one font and six character widths. Ten
national character sets are available. You can use office stationery or fanfold
paper.

The LA50 weighs 8.5 kilograms (18.7 pounds).

4—-8

VAXstation |I/GPX Owner's Manual, BA123 Enclosure

Figure 4-5:

The LAS0

14.2c¢m

(5.6 in}

(16 in)

MLO-860-85

To order an LA50 printer after the initial system installation, contact your sales
representative. You can install the LA50 printer yourself. After assembling
the printer, see the section Printer and Plotter Connection to the System.
For more information about the LA50 printer, see the following documents:
o

Installing and Using the LA50 Printer (Order No. EK-0LA50-UG)

LA50 Printer Programmer Reference Manual

(Order No. EK-0LA50-RM-

001)

The LCGO1

The LCGO1 is a high-resolution serial ink-jet color printer.

The LCGO01

provides 385 dots/centimeter (154 dots/inch) resolution and it prints in 216
. colors.

The printer offers five different fonts. One is ROM resident, and the others
are down-line loaded at system startup. The LCGO01’s automatic sheet feeder
holds paper and transparencies.

Options

4—9

The LCGO1 color printing system consists of the LCGO01 color printer and an
LCGO1 graphics protocol processor. The LCGO1 printer weighs 31.8 kilograms

(70 pounds), and the controller weighs 11.7 kilograms (26 pounds).

The

printer measures 21.6 centimeters (8.5 inches) x 61 centimeters (24 inches) x

61.6 centimeters (24.25 inches).

To order an LCGO1 color printing system after the initial system installation,
contact your sales representative. You can install the LCG01 yourself. After

assembling the printer, see the section Printer and Plotter Connection to the

System.
For more information about the LCGO01, see the following documents:

LCGO1 Installation and Operator Manual (Order No. EK-LCP01-IN)

LCGO1 User’s Guide (Order No. EK-LCP01-UG)

LCGO1 Pocket Service Guide (Order No. EK-LCP01-PS)

Plotter
The LVP16
The LVP16 is a high-performance 6-pen color graphics plotter. The LVP16
prints graphics at 38 centimeters/second (15 inches/second).

Using any of

19 character sets, the LVP16 can annotate graphs with text in any direction,
with or without character slant, and in varying sizes. The LVP16 is accurate

to 0.025 millimeter (0.001 inch).
Multicolor high-quality graphics are produced by programs, using the front-

panel selection of six pens. For drawing with additional colors, the program
can be stopped, and additional pens can be manually installed. The fiber-tip
pens are available in two nib sizes along with a selection of ten vibrant colors
for paper and seven for transparencies.

The LVP16 can be used with plain paper or transparencies.

Each page is

manually removed and inserted for every plotting.

The LVP16 weighs 7 kilograms (16 pounds) and measures 12.7 centimeters

(6 inches) x 56.8 centimeters (22.4 inches) x 36.7 centimeters (14.5 inches).
To order an LVP16 plotter after initial system installation, contact your sales
representative. You can install the LVP16 plotter yourself. After assembling

the printer, see the section Printer and Plotter Connection to the System.

4-10

VAXstation II/GPX Owner's Manual, BA123 Enclosure

To properly operate the LVP16, set the rocker switches according to the
following list.
This information supplements the LVP16 Graphics Plotter
Owner’s Manual.
e

B1 through B4 control baud rate. For example, set B1 and B4 to on for a
4800-baud rate.

The next two switches control paper size. For example, set to US and A4
for United States letter size paper.

The Y/D switch controls cabling. The D setting is for a direct connection,
and the Y setting is for the eavesdrop connection.

The S1 and S2 switches control byte size and parity. Set both to off for
8-bit bytes and no parity checking.

For more information about the LVP16, see the following documents:
®

LVP16 Graphics Plotter Owner’s Manual (Order No. EK-LVP16-OM)

LVP16 Graphics Plotter Programmer Reference Manual (Order No.

EK-

LVP16-RM)
®

The LVP16 Reference Card

Printer and Plotter Connection to the System
Cables are required to connect a printer or plotter to the VAXstation II/GPX.
The LNO03, LA210, LA50, and LCPO1 printers require the BCCO8 cable, and
the LVP16 plotter requires the BCC19 cable. You must order a cable in
addition to the printer or plotter.
For systems running ULTRIX, you must also add print commands to the
system (see the ULTRIX Workstation Software and Management Guide) and
set the printer for 7-bit ASCII (refer to the appropriate printer manual). To
connect a printer or plotter to a VAXstation II/GPX, follow the instructions
below.
1.

Make sure that the power switches for the printer or plotter and the
VAXstation I1/GPX are off.

Open the back door of the system unit.

Check that the printer or plotter and the system unit are set to the same
baud rate (4800).

Attach the larger end of the printer or plotter cable to the back of the
printer or plotter.

Options

4-11

Attach the free end of the printer or plotter cable to the printer port on the
I/0O distribution panel, which is located on the rear of your VAXstation

II/GPX (see Figure 4-6).

Figure 4—6:

Printer and Plotter Connection
to the System
TO PRINTER

1/0
DISTRIBUTION
PANEL

BAUD RATE

SELECTION SWITCH

N -/
6.

PRINTER

PORT

MLO-563-85

Close the back door of the system unit.

NOTE: If you are connecting the LA210 printer to the VAXstation 11/GPX,
make sure that XOFF and wrap are enabled. This may require toggling switches
on the printer as explained in the LA210 documentation.

4-12

VAXstation II/GPX Owner's Manual, BA123 Enclosure

Input Devices
The Tablet
The tablet system consists of a digitizing tablet, a puck, a 2-button stylus, and

a 1.5-meter (5-foot) power/signal cable. The tablet with the puck or stylus
may be used as a pointing device instead of the mouse for menu selection,
graphics entry, and cursor control.
The tablet is an input device that sends X-Y coordinates to the VAXstation
II/GPX puck on the tablet’s surface. The tablet has a resolution of 79 counts/
millimeter (200 counts/inch). The stylus is used like a pen, while the puck
is similar to a mouse, but instead glides on a felt bottom.

The tablet communicates with the VAXstation II/GPX through an asynchronous, full-duplex serial interface at 4800 baud (+/-2%).
The active area of the tablet is 279 millimeters x 279 millimeters (11 inches
x 11 inches). The tablet weighs 3.2 kilograms (7 pounds).

Figure 4—-7:
FEET

The Tablet
TABLET

PUCK

STYLUS

MLO-564-B5

To order a tablet after the initial system installation, contact your sales
representative. To install the tablet yourself, see Chapter 2.

Options

4-13

For more information about the tablet, see:

Tablet Information Sheet (Order No. EK-VSXXB-IN)

The Mouse
The mouse is a small, circular, plastic-bodied input device with three buttons.
You use the mouse and buttons to position the cursor, enter graphics, and
select on-screen items. Signals from the mouse are transferred to the monitor
through a 1.5-meter (5-foot) cable.

Memory
The Memory Modules
The VAXstation II/GPX comes with a minimum of 5 megabytes of memory.

Optional memory expansion modules allow you to expand to a total of
16 megabytes of memory. The following describes the additional memory
expansion modules:
Part Number

MS630-BA

Description

2M Memory Expansion Module, quad-height module with 256K
RAM (half populated MS630-BB).

MS630-BB

4M Memory Expansion Module, quad-height module with 256K

RAM.
MS630-CA

8M Memory Expansion Module, quad-height module with 256K
RAM.

To order a memory module after the initial system installation, contact your

sales representative. Contact your service representative to install a memory

module.

For more information about the memory modules, see:
®

KA630-A CPU Module User’s Guide (Order No. EJ-KA630-UG)

L PSITON

4—-14

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Video
The Video Subsystem
One VCB02 Video Subsystem consists of:
*

The M7169 base module

®*

One or, optionally, two M7168 4-plane modules

The VAXstation II/GPX is also available as a 2-user system with two VCB02

video subsystems, two color monitors, two input devices, and two keyboards.
The 4-plane module provides high-performance, high-resolution, full-page

direct memory access (DMA) color video subsystems based on the Q22-bus.
The module, based on a VLSI graphics coprocessor, off loads the MicroVAX
II/GPX main processor from computation-intensive graphics tasks.
The VAXstation II/GPX’s existing 4-plane video subsystem can display 16

colors simultaneously.
If a second 4-plane module is added, the video
subsystem is upgraded to an 8-plane video subsystem, which can display
256 colors simultaneously. The modules allow parallel processing in multiple
planes so that no degradation in performance occurs as planes are added.
The 4-plane module provides variable character size or positioning and inherent graphics capability. The module’s major hardware components are:

four video processor (DC322) chips, four planes of video memory with two
pages/plane, subsystem support logic, video shifters, and cable connectors
for the base module interface.
To order an additional 4-plane (M7168) module after initial system installation, contact your sales representative. Contact your service representative to
install this option.

For more information on the 4-plane module, see the following document:
*

VCBO02 Video Subsystem Technical Manual (Order No. AZ-GLGAB-MN),
which is in this binder.

Options

4-15

Storage Devices
The VAXstation II/GPX has four mass storage devices available as options.
They are:

The RD53 fixed disk drive

The RD54 fixed disk drive

The TK50 tape drive

The RX50 dual diskette drive

Table 4-1 shows the optional storage devices, the option package number,

and the controller that allows your system to access the storage device. You
can add optional storage devices up to your system’s limit. Contact your sales
or service representative to determine your system’s specific requirements.

Table 4—1:

Optional Storage Devices

Storage Device

Option Package

Order Number!

Required Controller

Fixed Disk Drives

RD53

RD53A-BA

RQDX3-BA

RD54

RD54A-BA

RQDX3-BA

Tape Drive
TK50

|
TK50-AA

TQK50-BA

RX50A-BA

RQDX3-BA

Dual Diskette Drive

RX50

1The option packages contain the storage device and necessary parts to completely connect it to your system.

The Fixed Disk Drives
The two fixed disk drives available for the VAXstation II/GPX are the RD54
and RD53. The RD54 has a formatted capacity of 159 megabytes. The RD53
has a formatted capacity of 71 megabytes.
A fixed disk drive provides additional data storage for the VAXstation II/GPX.
The fixed disk drive is mounted inside the system enclosure.
The VAXstation II/GPX in a BA123 Enclosure supports a maximum of four
fixed disk drives with either a 4- or 8-plane video subsystem. Contact your
service representative for information about your specific system capacities.

4-16

VAXstation II/GPX Owner's Manual, BA123 Enclosure

To order a fixed disk drive after the initial system installation, contact your
sales representative. Contact your service representative for installation.
For more information about the fixed disk drives, refer to the following
documents:

RD53 Disk Drive Technical Description (Order No. EK-RD53A-TD-001)

RDS54 Disk Drive Technical Description (Order No. EK-RD54A-TD-001)

The Tape Drive
The TK50 tape drive, with a TK50 tape cartridge, provides additional data

storage for your system and can be used to load software, including system
diagnostics.
For a more complete description of the TK50 tape drive, see Chapter 3. To
order a TK50 tape drive after the initial system installation, contact your sales
representative. You will need to order the tape drive, the TK50 tape cartridge,

and the signal cable option package. Contact your service representative to
install these options.
For more information about the TK50 tape drive, see the following documents:
®

TK50 Tape Drive Subsystem Owner’s Manual (Order No. EK-LEP05-OM)

TK50 User’s Guide (Order No. EK-OTK50-UG-001)

TK50 Technical Manual (Order No. EK-OTK50-TM-001)

The Dual Diskette Drive
For a description of the RX50 dual diskette drive, see Chapter 3. To order
an RX50 dual diskette drive after the initial system installation, contact your
sales representative. You will need the dual diskette drive option package
(RX50A-BA) and the signal cable option package (17-00867-01). Contact
your service representative to install this option.
For more information about the dual diskette drive, see the following document:

The RX50 Diskette Drive Technical Description (Order No.
TD-001)

EK-RX50A|

Options

4—-17

Communications
The Ethernet Communication Modules
The DEQNA is a Q22-bus-compatible communication module that interfaces

between an Ethernet Local Area Network (LAN) and a VAXstation II/GPX.
With a DEQNA module interface and communications software, the VAX-

station II/GPX system becomes a node on a network and can communicate
with other computers that are also nodes on the network. The DEQNA also

enables a VAXstation II/GPX to be down-line loaded with a system image from
a host computer on the network.
|

If the DEQNA module board is ordered after initial system installation, you
must contact your service representative to install it. Once the modules are
installed, the VAXstation II/GPX may join an existing Ethernet network either
through a DELNI or an H4000 transceiver.
The DELNI (Digital Equipment Local Area Network Interconnect) is a lowcost Ethernet device consisting of a short section of coaxial cable containing

eight transceivers.

Each transceiver supplies a port for one system on the

network. The DELNI is limited to a range of 35-40 meters (112-128 feet),

but can be expanded through a connection to a second DELNI or to a larger
Ethernet network. The ninth port on the DELNI allows for such a connection.
To order a DELNI, contact your sales representative.
The H4000 Ethernet Transceiver can accommodate a more extensive network.

The H4000 can be configured with 100 nodes for each 500-meter (1600-foot)
segment. The transceiver consists of a small printed circuit board and a cabletapping assembly contained in a rugged plastic housing. This installation also
requires a transceiver cable. To order an H4000 or transceiver cable, contact
your sales representative.

You may connect the system to a DELNI yourself. However, you must
contact your service representative to connect the VAXstation II/GPX to an
H4000 transceiver.

You need a BNE3x cable in order to connect a DELNI or an H4000 transceiver
to a VAXstation II/GPX. To order additional cable, contact your sales repre-

sentative. The BNE3x transceiver cable comes in four types:
e

BNE3A—PVC, straight connector

BNE3B—PVC, right-angle connector

BNE3C—Teflon, straight connector

BNE3D—Teflon, right-angle connector

4-18

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

The BNE3x cable comes in different lengths, specified by the part number
extension to the type of cable desired.
Part No. Extension

Length

-05

5 m (16.4 ft)

-10

10 m (32.8 ft)

-20

20 m (65.6 ft)

-40

40 m (131.2 ft)

For example, a BNE3C-20 is a 20-meter (65.6-foot) Teflon, straight connector.
For any questions regarding your specific requirements, contact your service
representative.

ThinWire Ethernet Components
This section describes the ThinWire Ethernet components you can use to
connect your VAXstation II/GPX, using ThinWire Ethernet.

ThinWire Ethernet Cable
The maximum recommended length of cable leading from a terminator to
the last station on a segment of ThinWire Ethernet is 185 m (606 ft). At least

0.5 m (1.6 ft) is required between stations.

Connectors
A ThinWire section is a single length of RG58C or equivalent cable. You will

need two connectors, one at each end, for each section of ThinWire cable.

Barrel Connectors and T-Connectors
A ThinWire segment is one or more sections of ThinWire cable interconnected
by barrel or T-connectors. You need one T-connector for each DESTA and
VAXstation I1/GPX.

DESTA and Transceiver Cable
If you want to connect a VAXstation II/GPX or any devices like the bridge,
repeater, or server that use transceiver cables to connect to ThinWire Ethernet,

you will need a DESTA and a transceiver cable.

Options

4—-19

Terminators
You need one terminator for each end of a ThinWire segment.

Connectors and Terminators
The ThinWire connectors and terminators you need to configure your ThinWire network follow:
®

T-connector (H8223)—A 3-way connector that joins two ThinWire Ether-

net cable sections. The third opening attaches to the system unit.
®

Terminator (H8225)—A connector at the end of a ThinWire segment

that provides the 50-ohm termination resistance needed for the cable. If

the ThinWire cable connects to a DIGITAL ThinWire Ethernet Multiport
Repeater (DEMPR), then a terminator is only needed at one end of the

cable.

Barrel connector (H8224)—A recessed connector that connects two ThinWire Ethernet cable sections.

Figure 4-8 shows the connectors and terminator you need to connect to
ThinWire Ethernet.

Figure 4-8:

Connectors
T-CONNECTOR

CONNECTOR

TERMINATOR

MLO--789-B6

BARREL
CONNECTOR

4-20

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Additional Equipment
Use the following equipment to connect a system with a transceiver cable to

ThinWire Ethernet:
*

DIGITAL ThinWire Ethernet Station Adapter (DESTA-AA)

DIGITAL ThinWire Ethernet Station Adapter (DESTA)
The DESTA is an Ethernet/IEEE 802.3 transceiver that connects systems that

have transceiver-type connectors to ThinWire Ethernet. A transceiver is a
device that provides a single physical connection between standard Ethernet

and Ethernet communication equipment.
The DESTA has two ports: one port connects to the T-connector connected
to ThinWire, a second port connects a transceiver cable that leads to the
system.

Figure 4-9 shows a DESTA.

The DESTA provides:

Connection of a system with a transceiver cable to ThinWire Ethernet.

Attachment to devices connected to Ethernet communication controllers
by way of transceiver cables.

Figure 4-9:

DIGITAL ThinWire Ethernet Station Adapter (DESTA)

MLO-791-88

Options

4-21

For more information on these options, see the following documents:
e

DEQNA User's Guide (Order No. EK-DEQNA-UG)

MicroVAX Handbook (Order No. EB-25156-47)

DELNI Installation and Owner’s Manual (Order No. EK-DELNI-IN)

Ethernet Installation Guide (Order No. EK-ETHER-IN)

Modems
Four modems are available for use with the VAXstation II/GPX:
Modem

Description

DF224

300, 1200, and 2400 bps (bits per second) full-duplex synchronous/
asynchronous

DF124

1200 and 2400 bps full-duplex synchronous/asynchronous

DF112

300 and 1200 bps full-duplex synchronous/asynchronous

DFO03

300 and 1200 bps full-duplex synchronous/asynchronous

DF224
The DF224 modem provides full-duplex communication at speeds of 300,
1200, and 2400 bps (asynchronous) and 1200 and 2400 bps (synchronous).
The DF224 allows both rotary pulse and pushbutton dialing over dial-up or

leased-line networks.
The DF224 contains an auto-dialer with memory and provides autoanswer

capability in addition to manual operation. A data/talk switch and automatic
adaptive equalizer are also provided. The DF224’s diagnostics test the modem
at each power up.
|
DF124
The DF124 modem provides full-duplex communication at speeds of 1200
and 2400 bps (asynchronous and synchronous) over dial-up or leased-line
networks.
The DF124 contains an autodialer with memory, a data/talk
switch, and diagnostic self-tests.

4-22

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

DF112

The DF112 modem communicates at 300 and 1200 bps full-duplex (asynchronous and synchronous) over dial-up or leased-line networks. An autodialer with memory and data/talk switch are provided. The DF112 is compatible with rotary dial and pushbutton dialing.
DFO03

The DF03 modem is a 300 and 1200 bps full duplex (asynchronous and
synchronous) modem.

To order a modem after initial system installation, contact your sales representative.

The DZQ11 Asynchronous Multiplexer
The DZQ11 is an asynchronous multiplexer that connects the Q22-bus with
up to four asynchronous serial data communications channels. A dual-height
module, the DZQ11 connects hard-copy and video terminals, with or without
modems, to a system. With a VAXstation II/GPX, the DZQ11 can also be
used as an asynchronous DECnet link. The DZQ11 allows dial-up (autoanswer) operations with modems capable of full-duplex operation, such as

DIGITAL’s models DF03, DF112, DF124, and DF224.

The DZQ11 provides flexible control of parameters, such as baud rate (50 to
9600), character length, number of stop bits for each line, odd or even parity
for each line, and transmitter-receiver interrupts. Additional features include
limited data set control, break generation and detection, and silo buffering of
received data.

To order a DZQ11 after the initial system installation, contact your sales
representative. You will need to order a base module (DZQ11-M) and a
cabinet kit (CK-DZQ11-DA). Contact your service representative to install
the DZQ11.

For more information about the DZQ11, see:

DZQ11 Asynchronous Multiplexer User’s Guide (Order No. ’EKWDZQI 1UG-001)

Options

4—23

‘The DHV11 Asynchronous Multiplexer
The DHV11 is an asynchronous multiplexer that connects up to eight serial

lines to a Q-bus for data communications.
The DHV11, a quad-height module with programmable functions, connects
hard-copy and video terminals to the VAXstation II/GPX. The DHV11 allows dial-up (auto-answer) operations with modems capable of full-duplex

operation, such as DIGITAL’s modems DF03, DF112, DF124, and DF224,

Applications for the DHV11 cover data concentration, terminal interfacing,
and cluster controlling.

The features include full modem control, DMA

or silo output, silo input buffering, programmable split speed, and module
throughput of 1500 characters/second.
To order

a DHV11 after the initial system installation, contact your sales

representative.

You will need to order a DHV11 base module (DHV11-M)
and cabinet kit, which includes filter connectors and cables (CK-DHV11-AB).
Contact your service representative to install the DHV11.

For more information about the DHV11, see:

DHVI11 Technical Manual (Order No. EK-DHV11-TM-001)

The DMV11 Synchronous Line Controller
The DMVI11 is a high-performance controller that operates at speeds up
to 56 kilobytes/second to provide efficient synchronous communications for
distributed networks.
Point-to-point configurations are practical when terminals have a high mes-

sage rate. However, the message rate of the terminals is usually very low,
even though the bit rate might be quite high. In those cases, sharing a

transmission line can significantly reduce the cost and improve the efficiency
of a communications network.
You will need to order a base module (DMV11) and one of four cabinet
kits. The DMV11 cabinet kit option you choose depends on the interface
requirements of your system.

4-24

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

NOTE: The RS-232-C standard has been superseded by the ELIA-232-D standard.
The four DMV11 cabinet kit options are:
1.

CK-DMV11-AA
M8053—-M Microcontroller/line unit (a quad-height module with multipoint microcode)

H3254 (V.35 or integral modem) Module test connector
H3255 (RS-423-A/EIA-232-D) Module test connector
BC08S-1K Cable

H325 and H3251 Cable turnaround test connector

70-20863-00 3.2 x 2.6 Panel
CK-DMV11-BA
M8053-M Microcontroller/line unit (a quad-height module with multipoint microcode)

H3254 (V.35 or integral modem) Module test connector

H3255 (RS-423-A/EIA-232-D) Module test connector
BC17E-25 Cable

H3250 Cable turnaround test connector
70-20861-1K Panel

CK-DMV11-CA
M8064-M Microcontroller/line unit (a quad-height module with mul-

tipoint microcode)
H3254 (V.35 or integral modem) Module test connector
7018250-1K Cable

H8568 and H8570 Terminators
70-20862-00 Panel

Options

4—-25

CK-DMV11-FA
e

MB8053-M Microcontroller/line unit (a quad-height module with multipoint microcode)

H3254 (V.35 or integral modem) Module test connector

H3255 (RS-423-A/EIA-232-D) Module test connector

BC08S Cable

H3251 Cable turnaround test connector

70-20864-00 Panel

To order

a DMV11 after the initial system installation, contact your sales

representative. Contact your service representative to install the DMV11.

For more information about the DMV11 synchronous line controller, see:

DMV11 Synchronous Controller User’s Guide (Order No. EK-DMV11-UG)

The DPV11 Synchronous Line Controller
The DPV11 is a low-cost single-line programmable interface that operates at
speeds up to 56 kilobytes/second to provide efficient synchronous communications for distributed networks.

The DPV11

is suited for interfacing to medium-speed synchronous lines for
The DPV11 is compatible
with DIGITAL's family of modems and with the Bell 200 Series modems and
remote batch and remote job-entry applications.

their equivalents.
To order a DPV11 after the initial system installation, contact your sales
representative. Contact your service representative to install the DPV11.

For more information about the DPV11, refer to the following document:

DPVI11 Technical Manual (Order No. EK-DPV11-TM)

4-26

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

The KMV11 Programmable Controller
The KMV11 is a high-performance direct memory access single-line programmable communications controller that operates at up to 64 kilobytes/
second to provide efficient synchronous or asynchronous communications for
distributed networks.

The KMV11 performs user-defined communications functions, thereby freeing
the host to do more application computations.

The KMV11 can be programmed in synchronous or asynchronous modes. It

also provides full modem support for DIGITAL'’s family of modems, the Bell
200 Series or equivalent, and European PPT-approved modems.
To order a KMV11 after the initial system installation, contact your sales
representative. Contact your service representative to install the KMV11.
For more information about the KMV11, refer to the following document:
e

KMV11 Programmable Communications Controller Technical Manual (Order
No. EK-KMV11-TM)

Options

4-—27

Chapter 5

Troubleshooting Procedure
This chapter, divided into three parts, provides troubleshooting information
for the VAXstation 1I/GPX:
*

POWER-UP MESSAGES—discusses the indications that appear when the
system is turned on.

BASIC TROUBLESHOOTING—provides a checklist of potential minor
problems with the system unit, fixed disk and diskette drives, tape drive,
pointing device and monitor, and corrective actions you can take.

MICROVAX DIAGNOSTIC MONITOR (MDM)—describes the VA
Xstation

II/GPX “MicroVAX Diagnostic Monitor System” (MDM) software tests and
the “Main Menu” maintenance options.

NOTE: If you have a diskless system that contains neither a TK50 tape drive nor
a floppy diskette drive, contact your service representative for additional system
troubleshooting and diagnostics.

Power-up Messages
During the power-up sequence, the VAXstation II/GPX executes built-in

diagnostic and bootstrap routines that provide maintenance information. The
information is displayed in single letters and numbers on both the lightemitting diode (LED) display, located on the CPU distribution panel on the
back of the VAXstation II/GPX system unit, and on the monitor screen.

Normally, the display progresses from F to 0 (going from F to A and then 8
to 0). A problem exists if the display stops in the F to 0 range.
e

If the display stops in the F to 3 range, a hardware error might exist in
the VAXstation II/GPX system. Contact your service representative.

If the display stops on A, check the keyboard connection and the pointing
device connection.

(See Setting Up the Keyboard and Pointing Device

section in Chapter 2.)
*

If the display stops on 2, check the “system does not boot from...” problem
indications listed in Table 5-1.

If the display stops on 1, the bootstrap device might not contain bootable
system software.

Complete the system software installation as directed

in the documentation supplied with your system software.

Basic Troubleshooting
Tables 5-1 through 5-5 list causes and corrective actions for minor system
problems that you can fix. The basic troubleshooting procedures are separated
into system unit, tape drive, fixed disk and diskette, and monitor problems.
If the corrective action does not work or the problem is more serious, run the
MicroVAX Diagnostic Monitor (MDM) system software to isolate the problem
(see the Maintenance System section of this chapter) and contact your service
representative.

Monitor fuse replacement instructions and mouse maintenance procedures

follow Table 5-5.

5—2

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Table 5—1:

System Unit Troubleshooting Procedures

Power Up

Problem |

Possible Cause

Corrective Action

No response when the
power switch is turned

System is not plugged
in.

Set the power switch to 0 (off).

to 1 (on).

Plug in the system. Set the power

switch to 1 (on).
Wall outlet is faulty.

- Use a different wall outlet.

System circuit breaker

Set the power switch to off. Reset the circuit breaker by pressing

is tripped.

down and then pulling up the circuit breaker lever. (See Figure 5-1.)

Set the power switch to on. If the
circuit breaker trips again, contact
your service representative.

Figure 5—-1:

System Circuit Breaker

CIRCUIT
////////”BHEAKEH

MLO-566-85

Troubleshooting Procedure

5—3

Table 5—-1 (Cont.):

System Unit Troubleshooting Procedures

Power Up

Problem

Possible Cause

Corrective Action

No response when the
power switch is turned

Power cable is incorrectly installed.

Set the power switch to off. Check
that the cable is fully seated into the
socket in the back of the system.
Set the power switch to 1 (on).

on.

Power is on, but the

Monitor is off.

Turn on the monitor.

Monitor cable is incorrectly installed.

Make sure that the monitor cable is
installed properly. (See Chapter 2.)

Brightness and contrast controls are not

Adjust brightness and contrast con-

display on the monitor does not appear.

trols.

set properly.
Rear panel LED dis-

Insert bootable system software disk-

play indicates a power-

ette.

up error.

Keyboard cable installed Make sure the keyboard cable is inincorrectly.

stalled properly. (See Chapter 2.)

A keyboard key or point- Remove anything that may be activating these devices and reboot the
ing device pushbutton
is accidentally pressed

system.

during a system boot.
Instead of automatically The Halt Enable/Disable switch is set to
booting when the
power switch is turned

the Enable position (the

on, the arrow prompt

system is set to con-

(>>>) is displayed on

sole mode).

the monitor.

when the system di-

You failed to insert a
system diagnostic medium into the load de-

agnostics are running.

vice in the time allot-

Monitor displays the
message ?54 RETRY

Type B DUAO and press the Return
key to boot the system.

Press the Restart pushbutton to re-

boot the system. Insert a diagnostic
medium.

ted.

5—4

Or, exit

console mode by setting the Halt
Enable/Disable switch to the disable (down) position and then press
the Restart pushbutton to have the
system boot automatically.

VAXstation II/GPX Owner's Manual, BA123 Enclosure

Table 5-1 (Cont.):

System Unit Troubleshooting Procedures

Power Up :
Problem

Possible Cause

Corrective Action

System dm not boot

The Fixed Disk Ready
pushbutton is in, or
drive is not ready.

Press and release the Fixed Disk

System software is not
on the disk.

Load (install) the system software

from the fixed disk
drive.

Ready pushbutton.

on the fixed disk, using the system

software installation instructions
supplied with the software.
System does not boot

from the TK50 tape

drive.

Fixed Disk Ready push- Press in the Fixed Disk Ready
button is not in.
pushbutton.
Tape is worn or dam-

Try another tape.

aged.
Tape cartridge release

System does not boot
from the diskette drive.

Press down the Vcartridge release

handle is not locked.

handle.

TK50 tape is not fully
inserted into the tape

Make sure the tape is fully inserted
and the cartridge release handle is

drive.

locked down.

Diskette is not in the
diskette drive.

Insert a diskette containing bootable
system software in diskette drive 1

and enter the applicable boot com-

mand for the device.
Diskette drive door is

Close the diskette drive door.

open.

Diskette is upside down
in the diskette drive.

Align the orange stripe on the diskette with the stripe on the diskette
drive.

Diskette is not bootable. Use a diskette containing bootable
system software.

Diskette is worn or dam- Try another diskette.
aged.
Diskette is write pro-

Remove the foil tab covering the

tected.

write-protect notch or use a differ-

ent diskette.

Troubleshooting Procedure

5—5

Table 5—1 (Cont.):

System Unit Troubleshooting Procedures

Power Up

Problem

Possible Cause

Corrective Action

System does not reboot when power

Powerswitch wasnot
set in off position for

Set power switch to off for at least
15 seconds before pressing to the 1

switch is pressed off

enough time.

(on) position.

Problem

Possible Cause

Corrective Action

System halts unexpectedly during normal operation.

The Halt pushbutton
Press the Restart pushbutton. Set
was pressed (the systhe Halt Enable/Disable switch to
tem is in console mode). the disable (down) position to pre-

and on.

System Halts

vent unwanted recurrences.

Table 5—-2:

Fixed Disk and Diskette Drives Troubleshooting
Procedures

Read and Write Errors

Problem

Possible Cause

Corrective Action

Fixed disk read error
message is displayed.

Fixed Disk Ready
pushbutton is in.

Press and release the Fixed Disk
Ready pushbutton.

Disk is write protected.
(Write-Protect pushbut-

Press and release the Write-Protect
pushbutton so it does not glow.

ton glows orange)

Fixed disk write error
message is displayed.

Disk is write protected.

Press and release the Write Protect
pushbutton.

Diskette read error mes- The diskette drive is
sage is displayed.
empty.

Insert a diskette into the diskette
drive.

Diskette drive door is

Close the diskette drive door.

open.

Diskette is upside down Align the orange stripe on the diskin the diskette drive.
ette with the stripe on the diskette
drive.

5—6

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Table 5—2 (Cont.):

Fixed Disk and Diskette Drives Troubleshooting Procedures

Read and Write Errors
Problem

Possible Cause

Corrective Action

Diskette is not format-

Use a preformatted RX50 diskette.

ted.
Diskette is worn or dam- Try another diskette.

aged.
Diskette write error

The diskette drive is

message is displayed.

empty.

Diskette drive door is

Insert a diskette in the diskette drive.
Close the diskette drive door.

open.

Diskette is upside down

Align the orange stripe on the disk-

in the diskette drive.

ette with the stripe on the diskette
drive.

Diskette is not format-

Use a preformatted RX50 diskette.

ted.

Diskette is worn or dam- Try another diskette.
aged.

Diskette is write protected.

Table 5—-3:

Remove the foil tab covering the
write-protect notch.

Tape Drive Troubleshooting Procedures

Problem

Possible Cause

Corrective Action

TK50 passes the power-

Tape is not in the drive,

up test but does not

Insert the tape and press the Load/

or the drive is not

work.

Unload pushbutton.

loaded.
Load/Unload pushbut-

Press the Load/Unload pushbut-

ton is out.

ton.

TK50 Load/Unload red

A problem exists with

indicator flashes rapidly

Press the Load/Unload pushbutton

the tape drive.

and no unusual sounds

are heard.

four times. If the problem persists,

~ do not attempt to use the tape drive
or to remove

the tape cartridge.

Call your service representative.

Troubleshooting Procedure

5—7

Table 5—3 (Cont.):

Tape Drive Troubleshooting Procedures

Problem

Possible Cause

Corrective Action

Load/Unload indicator
flashes rapidly and you

Leaders are not properly coupled.

Immediately turn off the system by
pushing the on/off switch to 0 (off).
Do not attempt to use the tape drive
or to remove the tape cartridge.

hear a whirring sound.

Call your service representative.
Tape cartridge release

The power-up test is

Wait for the Load/Unload indicator

handle does not lift.

still in process.

to stop glowing and the Tape Activity indicator to glow green. Try

again. If the problem persists, call
your service representative.

System power is not

Turn on the system power.

on.

Tape cartridge release
handle does not lock.

Tape is not inserted
properly.

Reinsert the tape cartridge.

If the

problem persists, call your service
representative.

Tape does not unload.

The Load /Unload push- Make sure the Load/Unload pushbutton is in the unload position.
button is in load position.

Table 5—4:

Wait for the indicator to go out before trying to remove the tape.

Monitor Troubleshooting Procedures

Problem

Possible Cause

Corrective Action

Power indicator on the

Power cord is not con-

front of the monitor

nected to the monitor
or the wall outlet.

Connect the power cord to the monitor and wall outlet.

does not light green

when you turn on the
monitor.

5—8

Monitor is not turned

Turn on the system and then the

on.

monitor.

No power exists at the
wall outlet.

Use another outlet.

Monitor fuse is blown.

Replace the fuse. See the Replacing
the Fuse section.

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Table 5-4 (Cont.):

Monitor Troublesl ooting Procedures

Problem

Possible Cause

Corrective Action

Screen is blank and
power indicator on the
front of the monitor is
lit.

System’s CRT saver fea- Press any key to reactivate the disture is activated.
play.

Screen goes blank after successful power up,
and the power indi-

Monitor fuse is blown.

Replace the fuse. See the Replacing
the Fuse section.

cator on the front of

the monitor goes out.
Screen displays raster,

Signal cable is discon-

Secure the video cable connection

but no cursor or text

nected.

between the monitor and the system.

appears.

System is not on.

Turn on the system.

Contrast control is set

Turn up the contrast control.

to minimum.

Host system’s CRT saver Press any key to reactivate the dis-

Screen display is distorted, rolling or flickering, or the wrong

feature is activated.

play.

Video cable is incor-

rectly installed.

Make sure that the video cable is
installed properly.

Electromagnetic interference exists.

seconds. After 30 seconds, recheck

color appears.
For the color monitor,
color is not even; poor

color purity.

Press the degauss switch for a few

purity.
Move any electromechanical device
away from the monitor or move the
monitor.

CAUTION: Before moving the monitor, turn the monitor off and wait 30 seconds
to allow static electricity on the CRT to discharge.

Troubleshooting Procedure

5—9

Table 5-5:

Pointing Device Troubleshooting Procedures

Problem

Possible Cause

Corrective Action

Mouse does not track

The tracking ball is

Clean the tracking ball.

properly.

dirty.

Mouse Maintenance section.

Pointing device indi-

Cable is installed incorrectly.

Unplug and then replug the cable

cator does not appear

on the monitor screen,
or the monitor does

to reset the device.

See the

(See Chapter

not respond to the pointing device commands.

Replacing the Fuse
If the Monitor Troubleshooting Procedures (Table 5-4) indicate that you need
to replace the fuse for the monitor, follow the instructions.

Color Monitor
The color monitor has an automatic voltage-switching mechanism. Therefore,
you do not need to change the voltage switch setting. Use either of the
following fuses:

3AG, a 2-Amp, 250-volt, slow-blow fuse.

(DIGITAL part number:

12-

(DIGITAL part number:

12—

14676-04)

IEC, a 2-Amp, 250-volt, slow-blow fuse.
19283-03)

5—10

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Figure 5—2:

Fuse Location, Color Monitor

POWER
CORD
L~ CONNECTOR

POWER

SWITCH

VIDEO

CABLE

ASSEMBLY

TO WALL
OUTLET
MLO-872-85

To replace the fuse:

Turn off the power and wait 10 seconds to allow the voltage to dissipate.

WARNING: You must wait a full 10 seconds or the voltage may harm you.
2.

Unplug the power cord from the wall outlet and then from the monitor.

Troubleshooting Procedure

5—11

Carefully pry out the fuse carrier with a screwdriver.

FUSE

POWER CORD

/ CONNECTOR

POWER

SWITCH

VIDEQ CABLE

ASSEMBLY

| }

RELEASE TA

®
J

MLO-868--86

Carefully pry open the release tab, remove the inner fuse holder, and

Replace the inner fuse holder in the fuse carrier.

Replace the fuse carrier in the back of the monitor.

Plug the power cord back into the monitor and then into the wall outlet.

replace the fuse.

Turn on the power.

5—12

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Mouse Maintenance
The rubber-coated ball under the mouse can be removed for cleaning or
replacement. Clean the ball when the mouse fails to smoothly move the

cursor on the screen. In an average office environment, cleaning the ball
every 6 months is sufficient.
To remove and clean the mouse ball:;

Turn the mouse upside down. Remove the ball housing cover plate by

placing your fingers in the grooves on the plate and turning the plate

counterclockwise.

MLO-B6BA-88

Troubleshooting

Lift off the cover plate and remove the ball.

MLO-568B-85

Clean the ball with lukewarm water and, if necessary, a mild soap.

CAUTION: Do not use organic solvents such as toluene or trichlorethane,
which will damage the rubber coating.
4.

Dry the ball with a soft, lint-free cloth.

5—14

VAXstation |I/GPX Owner's Manual, BA123 Enclosure

Replace the ball and cover plate.

MLO-568E-85

Troubleshooting

Lock the cover plate into position by placing your fingers into the grooves
on the cover plate and turning it clockwise.

MLO-588F-85

5-16

VAXstation II/GPX Owner's Manual, BA123 Enclosure

MicroVAX Diagnostic Monitor
The ‘"MlmoVAX Diagnostic Monitor” (MDM) system software provides user
tests that isolate and identify faults in the system. Use this software to
test the system in response to an error message or to test your system

perlodlcally

Test the system (and record the results) before calling your

service representative.

In addition, the maintenance software displays list system utilities and system
devices.
The maintenance software is stored on RX50 diskettes or on a TK50 cartridge.
To run the maintenance programs and to call VAXstation II/GPX system

displays, use the monitor and keyboard for command inputs.

The MicroVAX Diagnostic Monitor Main Menu
The “MicroVAX Diagnostic Monitor Main Menu” display lists the testing
options. See the Checking the System section of Chapter 2 for instructions

on accessing the “Main Menu.”
Press the RETURN key to continue.

MAIN MENU

1 -- Test the system
2 -- Display System Configuration and Devices

3 -- Display the System Utilities Menu
4 -- Display the Service Menu

5 -- Exit MicroVAX Diagnostic Monitor
Type the number;

then press the RETURN key.

The following maintenance system options appear in the “Main Menu” in the
previous picture:

1—Test the System. This option tests the devices supplied by DIGITAL
for a VAXstation II/GPX system. See the Checking the System section

of Chapter 2 for instructions on testing devices.

Troubleshooting Procedure

5-—17

2—Display System Configuration and Devices. This option displays a list
of the devices supphed by DIGITAL for a VAXstation II/GPX system. A

sample screen is shown in the following illustration. Your configuration
might be different from this example.
Type the number;

then press the RETURN key.

SYSTEM CONFIGURATION AND DEVICES
SYSTEM CONFIGURATION
CPUA.
. .MicroVAX CPU

KA630-AA 1MB,

FPU MOO HOO

MEMA.
. .MicroVAX memory system
2 megabytes,

4096 Pages.

KA630. ..CPU module,

1MB on-board memory.

MS630-AA.. .Dual height memory module, 1MB.
RQDXA. . .Winchester/diskette controller.
Revisions=10 and 6
...cannot identify drive,
RX50.
. .Removable

Offline.

RX50.
. .Removable
DEQNAA.
. .Ethernet controller.
O0B-00-2B-02-17-D3
VCBO2A.
. .Graphics Processing Extension
Press the RETURN key to return to the previous menu.

NOTE: The last letter in each device listed differentiates among multiple devices
of the same type. For example, DEQNAA indicates one DEQNA module; DEQNAB
a second, and so forth.

NOTE: When you have two of the 8-megabyte memory options (MS630-CA)
installed, you receive a message that the 1-megabyte of memory on-board the

CPU is disabled. This message does not indicate an error. VAXstation II/GPX
systems have a 16-megabyte limit on physical memory.
®
e

3—Display the System Utilities Menu, which allows you to format your
fixed disk.
|
|
4—Display the Service Menu.

This option displays the Field Service

diagnostics. Only your service representative should use this menu. (See
the VAXstation Maintenance Guide for additional information.)

5—Exit MicroVAX Diagnostic Monitor.
from the “Diagnostic Monitor”.

5—-18

This option allows you to exit

VAXstation I/GPX Owner's Manual, BA123 Enclosure

The System Utilities Menu
~ The only option in this menu is the Customer Disk Drive Formatter. This
option allows you to format a fixed disk or a diskette. Your fixed disk or
diskette must be formatted before you can use it to store data.

CAUTION: Formatting a fixed disk or diskette destroys all data on the disk or
diskette. Use the formatting utility only if you have made copies of any data on
the disk you want to save or the disk is empty.
To format a system fixed disk or a diskette in the diskette drives with the
screen displaying the System Utilities screen:
1.

Type 1 and press the RETURN key.

If you are formatting a fixed disk you are prompted to write-protect all

the drives except the one you want to format. Push the write-protect
pushbutton to make sure that it is in the out (write-enable) posntmn on
the drive control panel.
If you are formatting a diskette, remove the write-protect foil tab on the
diskette and insert the diskette into the diskette drive.
Press the RETURN key. The screen displays a list of the drives and their
unit numbers and prompts you for the number of the unit (drive) you
want to format.
Type the number of the unit and press RETURN. You are asked to verify
the unit number.
If the unit number is correct, type 1 and press the RETURN key. If the
unit number is incorrect, type 0 and enter the correct unit number.

The screen displays status messages as the formatting continues and informs
you when the formatting process is complete.

Troubleshooting Procedure

5—19

—

Chapter 6

Service
If you are unable to correct a problem with your VAXstation II/GPX system,
contact your service representative.

How to Call for Service
Before you call:
1.

Check the problem-solving suggestions listed in Chapter 5. You can often
solve a problem yourself.

Write down the serial and model numbers of your VAXstation II/GPX.
The numbers are located on the rear panel of the system unit (and on
the service tag on system front panel).

Summarize the problem. Make a note of what you were doing when the
system failed. Note if any indicators turned on or off, or if you heard
any new sounds before or after the system failed.

Who you call:
1.

Call your service representative.

If you are under warranty or have a

DIGITAL service contract, you may also call the customer support center

for assistance. In the United States, the customer support hot line number
is 1-800-DEC-8000. If you are located outside the United States, contact

your sales representative for the local service branch office phone number.

Service

6-—1

When you call:
1.

Stay near the VAXstation II/GPX.

Have all your materials available (for example, manual, serial and model
numbers, and problem summarization). That will assist the service representative with helping you.

NOTE: If you return the VAXstation 1I1/GPX to DIGITAL for service, repack
the system or modules in their original shipping containers.

DIGITAL Services
Your DIGITAL hardware warranty gives you access to DIGITAL's best resources, including technical expertise, spare parts inventories, and worldwide
service.

After warranty, DIGITAL'’s support continues through optional on-site and
off-site services for as long as you own your DIGITAL hardware. DIGITAL's
on-site services include fast response time and full support, including the cost
of parts and labor. Contact your service representative for a description of
the DIGITAL services available in your area.

6—2

VAXstation II/GPX Owner's Manual, BA123 Enclosure

Appendix A

VA Xstation 11/GPX System

Specifications
Table A-1:

Input

System Electrical Requirements

Specifications’
120 V ac

220 V ac

Voltage range

88-128 V

176-256 V

Power source phasing

single

Frequency

60 Hz

50 Hz

47-63 Hz

Running current (typical)

8.8 A

4.4 A

Power consumption (maximum)

690 W

Line frequency range

1These requirements depend on the line voltage setting that you select.

VAXstation II/GPX System Specifications

A—1

System Environmental Requirements

Table A—-2:

Operating

Nonoperating

Maximum altitude

2400 m

12000 m

Temperature range’

15-32 deg. C

-40-60 deg. C

(60-90 deg. F)

(-40-140 deg. F)

20%-80%

10%-95%

Relative humidity

IReduce the maximum temperature specification by 1.8 degrees Celsius (3.24 degrees Fahrenheit) for each
'

1000-meter increase in altitude.

NOTE: Your service contract may require limits for temperature and humidity
that override the limits listed above.

Color Monitor Specifications

Table A—-3:
Description

Characteristics

Physical

Height
Width
Depth

Weight

47 cm (18.5 in)
51.8 cm (25 in)
54.6 cm (21.5 in)

Approximately 41 kg (90 1b)

Picture Tube Size Diagonal
480 mm (19 in) viewable
Video Format

RGB color, composite video

Display Characteristics

0.31 mm dot pitch with high efficiency antiglare treatment

1024 x 864 pixels, giving approximate picture size of
326 x 275 mm

Timing

Vertical rate
Horizontal rate

A—-2

60 Hz
54 KHz

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

Table A-3 (Cont.):

Color Monitor Specifications

Description

Characteristics

Video R and B Input Signals
0.7 V pp/75 Ohm
Video G Composite Signal
1V pp/75 Ohm

Power
AC input

88-132 V, 50/60 Hz

185-264 V, 50 Hz
Power consumption

150 W (nominal)

Fuse (either may be used)

2A, 250 V slow blow (3AG)
DIGITAL part no. 12-14676-04

2A, 250 V slow blow (IEC)
(European designation T2A-250 volt)

DIGITAL part no. 12-19283-03

External Controls
Contrast
Brightness

Degauss
Tilt-lock lever

On/off
Operating Temperature Range
10-40 deg. C (50-104 deg. F)

Humidity

10%-95% relative humidity, noncondensing

VAXstation II/GPX System Specificatigns

A—3

Table A—4:
Description

Mouse Specifications
Characteristics

Physical

Height

4 cm (1.57 in)

Diameter

8.8 cm (3.47 in)

Weight

0.82 kg (0.37 1b)

Cable

1.5 m (5 ft) in length, 0.38 cm (0.15 in) diameter, six
conductors, shielded, high flexibility design

Connector

7-pin Micro-DIN type (male)

Temperature

Operating
Nonoperating

10-40 deg. C (50-104 deg. F)
-40-66 deg. C (-104 deg. F-140 deg. F)

Electrical

Power
Interface

+5 V +/-5% at 130 mA
-12 V +/-10% at 20 mA (serial)
RS-232 voltage level compatible
TTL compatible

FCC/EMI

A—4

Class B certified

VAXstation II/GPX Owner's Manual, BA123 Enclosure

Table A—4 (Con
Description

t.):

Mouse Specifications
Characteristics

Performafice
Resolution

79 counts/cm 250 counts/in

Tracking speed

73.5 cm/sec (30 in/sec)

Accuracy

+/-3% 0-24.5 cm/sec (0-10 in/sec) any direction
+/-15% 24.5-49 cm/sec (10-20 in/sec) any direction
+/-30% 49-73.5 cm/sec (25-30 in/sec) any direction

Operating

Modes

Incremental Stream Prompt

Data format

Delta Binary

Sampling rate

55 reports/sec in incremental stream mode, up to 95
reports/sec when polling

Baud rate

4800 baud

Pin assignments
Pin
1

Function
ground

transmit data

receive data

-12V

+5V

not used (+12 V)

not used

shell

protective ground

Table A-5:
Description

Tablet Specifications
Characteristics

Physical

Construction

Molded, high-impact plastic

Finish

Fine matte finish to minimize glare and fingerprints

Color

Light gray

VAXstation 1I/GPX System Specifications

A—5

Table A-5 (Cont.):
Description
Power/signal cable

Tablet Specifications
Characteristics
1.5 m (5-foot) cable wired to tablet, terminated in a
7-pin Micro-Din connector

Height

2 cm (0.8 in)

Width

41.2 cm (16.2 in)

Length

40.6 cm (16 in)

Weight

3.2 kg (7 1b)

Performance
Resolution

79 counts/mm 250 counts/in

Active area

279 mm x 279 mm (11 in x 11 in)

Proximity

1.27 cm (0.5 in) cursor

(Nominal)

0.63 cm (0.25 in) stylus

Interfaces

Serial, asynchronous, full-duplex, with R5232C signal
levels

Sampling Rate

55, 72, or 120 pairs/sec

Data Rate

4800 or 9600 baud (software selectable)

Coding

Binary 5-byte format. The first byte contains synchronization, pushbutton status, and proximity information. Second and third bytes have absolute
X coordinate positions. The fourth and fifth bytes
have absolute Y coordinate positions. Each byte is
found by one start bit and one stop bit. The data
byte contains 8 bits of data and 1 bit for parity (odd

parity).
Coordinate origin

Lower left corner of active area

Operating Modes
- Remote request

Incremental

Diagnostics

X-Y coordinate update and proximity report when
polled by host

Position reports are generated as long as cursor is
in motion.
Reports are also generated when the
pushbuttons are pressed or released.
Built-in diagnostics that check electronics, communication, tablet, and transducers

A—6

VAXstation 1I/GPX Owner's Manual, BA123 Enclosure

Table A-5 (Cont.):

Tablet Specifications

Descriptidn

Characteristics

Interface

Description

EIA RS232C compatible signals

Power requirements

+12 Vdc +/-10% at 0.3 A

Output connector
(Power and Data)

7-Pin Micro-Din (male)

Mating connector

7-Pin Micro-Din (female)

Pin assignments

7 Pin (RS232C)

\;a\m#wnfiag

Function
signal and power signal

Table A—-6:

transmit data (from tablet)
receive data

not used
not used
+12V
tablet present

RD53 Fixed Disk Drive Specifications

Description

Characteristics

Storage
Total capacity

71,303,168 bytes

User capacity

70,987,776 bytes
138,648 blocks

User capacity

Performance!
Average seek time

30 msec

Average rotational latency

8.33 msec

Average access time

38.33 msec

Transfer rate

184.32 kb/sec

Physical
Height

8.25 cm (3.25 in)

Width
Depth

20.32 cm (8 in)

Weight

3.18 kg (7 1b)

14.6 cm (5.75 in)

1When operating with RQDX3 controller

VAXstation |I/GPX System Spec

A-7

Table A-7:

RDb54 Fixed Disk Drive Specifications

Description

Characteristics

Storage

Total capacity

191 mbytes

User capacity

159 mbytes

User capacity

310,550 blocks

Performance!
Average seek time

30 msec

Average rotational latency

8.33 msec

Average access time

38.3 msec

Transfer rate

5 mb/sec

Physical
Height

8.255 cm (3.38 in)

Width

14.60 cm (5.75 in)

Depth

20.32 cm (8.20 in)

Weight

2.8 kg (6.3 1b)

1When operating with RQDX3 controller
Table A—-8:

RX50 Dual Diskette Drive Specifications

Description

Characteristics

Medium
Diskettes /RX50 drive—2
Recording surfaces/

diskette—1

Storage capacity
Per diskette (80 tracks)

409,600 bytes

Per track (10 sectors)

5120 bytes

Per sector (1 logical block)

512 bytes

Performance!
Average seek time

164 msec

Average rotational latency

100 msec

Average access time

264 msec

Transfer rate

12.8 kb/sec

1When operating with RQDX3 controller

A—8

VAXstation II/GPX Owner's Manual, BA123 Enclosure

Table A-8 (Cont.):

RX50 Dual Diskette Drive Specifications

Description

Characteristics

Physical
Height

8.5 cm (3.25 in)

Width
Depth

14.6 cm (5.75 in)
21.6 cm (8.50 in)

Weightr

2.8 kg (4.18 1b)

Table A-9:

TK50 Tape Drive Specifications

Description

Characteristics

Medium
Magnetic tape
Dimensions

1.27 cm (0.5 in) wide

183 m (600 ft) long
Mode of operation

Streaming

Read/Write method

Serpentine

Recording density

16,934 bits/cm (6667 bits/in)

Number of tracks

Capacity
Unformatted

131 mb

Formatted

94.5 mb

Performance
Tape start time
Tape speed

190.5 cm/sec (75 in/sec)

Streaming data rate

500 kb/sec

Access time

1 min minimum

(from insertion of a new

35 min maximum

tape)
Physical
Height

8.25 cm (3.25 in)

Width

14.60 cm (5.75 in)

Depth

21.44 cm (8.44 in)

Weight

2.27 kg (5 Ib)

VAXstation II/GPX System Specifications

A—9

Appendix B

VAXstation II/GPX Related

Documents

This appendix lists and describes documents pertaining to a VAXstation II/
GPX system in the BA123 enclosure.

The first section deals with hardware. Sections on ULTRIX software and
MicroVMS software follow. Refer to the software section applicable to your
system. Each software section lists both operating system and workstation
documentation.

The last page of this book provides information on ordering documentation.

Hardware
BA123 Site Preparation and Verification Guide (Order No. EK-BA123-SP)
provides planning information for system installation. The guide contains
space, power, and environmental suggestions.

VCBO02 Video Subsystem Technical Manual (Order No. EK-104AA-TM)
describes the operation and programming of the VCB02 module. The
manual is packaged in the same binder as this book.
MicroVAX II Maintenance Kit (Order No. ZNABX-GZ)

VR290 Color Video Monitor Installation/Owner’s Guide (Order No. EKVR290-IN) describes how to install, operate, and troubleshoot the color
monitor.

Mouse Installation Sheet (Order No. EK-VSXXA-IN) explains how to set
up the mouse.
Tablet Installation Guide (Order No. EK-VSXXB-IN) explains how to set
up the tablet.
KA630-A CPU Module User's Guide (Order No. EK-KA630-UG) details
the internal operation of the MicroVAX KA630-A CPU.

VAXstation II/GPX Related Documents

B—1

MicroVAX II Maintenance Information Kit (Order No. ZNA3X-C3) explains
how to service systems.

ULTRIX Software !
ULTRIX-32m Documentation Kit Overview (Order No.

AV-CN33C-TE)

describes the ULTRIX-32m documentation set. You may order the entire

ULTRIX-32m documentation set as a unit (Order No. QZ832-GZ).

ULTRIX-32m Release Notes (Order No. AA-CN34C-TE) contains information about last-minute changes to the software and documentation.

ULTRIX-32m Installation Guide (Order No. AA-CN29C-TE) describes the
ULTRIX-32m operating system installation procedure for a system that

includes a MicroVAX processor.
ULTRIX-32m System Manager’s Guide (Order No.

AA-CN28C-TE) con-

tains information for the person responsible for operation and care of a
system running ULTRIX-32m.

ULTRIX-32m Programmer’s Manual Section 1 (Order No. AA-CN25C-TE)

describes the commands accessible to all system users.
ULTRIX-32m Programmer’s Manual Section 2 and 3 (Order No. CN26C-TE)

explains systems calls and subroutines of interest to system programmers.
ULTRIX-32m Programmer’s Manual Section 4, 5,

7, and 8 (Order No.

CN27C-TE) describes special system files, file formats, macro packages

and conventions, and system maintenance commands.
ULTRIX-32m Master Index (Order No. AA-CN36C-TE) allows fast access
to information in the ULTRIX-32m documentation set. Individual indexes

are included in each book.

ULTRIX-32m Supplementary Documents Volume I (Order No. AA-CN30ATE), ULTRIX-32m Supplementary Documents Volume II (Order No.

AA-

CN31B-TE), and ULTRIX-32m Supplementary Documents Volume III (Order No. AA-CN32A-TE) contain articles about various components of
the ULTRIX system. Programmers who designed the components wrote
these articles.

Some of the material in these volumes may be partially

! These documents pertain only to customers in the United States. If you are not a U.S. customer or if you
require translated documents, check the appropriate country’s product listing.

B—2

VAXstation Il/GPX Owner's Manual, BA123 Enclosure

inaccurate or dated.

These articles are provided to augment the refer-

ence and task-oriented information contained in the other ULTRIX-32m

documentation.

ULTRIX-32w Documentation Kit Overview lists the ULTRIX-32w documentation set. You may order the entire ULTRIX-32w documentation set

as a unit (Order No. 00-Q4X32-GZ).
ULTRIX-32w Technical Summary (Order No.

AA-GT87A-TN) describes

the architecture, concepts, and nomenclature of the workstation software.

ULTRIX-32w Installation and Management Guide (Order No. AA-GT88ATN) discusses the installation and management of the workstation software subsets.

Using and Customizing the Window Manager (Order No. AA-GT89A-TN)

introduces the new user to the ULTRIX workstation environment.

The

manual describes how to use the window system and how to change the
environment to suit the user’s needs.
ULTRIX-32w QDSS/VCBO02 Driver Reference (Order No. AA-GT90A-TN)

describes the ULTRIX kernel services that support the QDSS and other
VAXstation II/GPX system hardware. The manual outlines device driver

support of the VAXstation hardware and specifies the various driver
services.

ULTRIX-32w

QDSS Interface Library Programming (Order No.

AA-

GT91A-TN) describes the optional ULTRIX C language library routines

and macros that allow direct access and control of the QDSS/VCB02
graphics subsystem.

The guide is intended for software engineers who

are writing applications and need the performance afforded by direct
access to the QDSS hardware.

ULTRIX-32w Xlib Programming Reference (Order No. AA-GT92A-TN)
describes the architecture, nomenclature, and C language interface of

the ULTRIX application or window server and the terminal emulators.
This provides a complete reference to the X window server C library,
which supplies program control over text, graphics, window, and client

applications.

ULTRIX-32w GKS/0b Programming (Order No. AA-GT93A-TN) describes

the operating system implementation of VAX GKS/0b.

The guide dis-

cusses the program environment and the workstation specifics for QDSS,
LNO1, and X server. The guide also provides a reference to the C and
FORTRAN (f77) GKS calls.

VAXstation 1I/GPX Related Documer

ULTRIX-32w Services Reference (Order No. AA-GT94A-TN) includes
descriptions of important programs and subsystems. This section can
either be used separately, or individual pages can be inserted in the
user’s operating system Programmer’s Manual.
C Language X Interface (Order No. AA-HF10A-TN) describes the X
window system software. Two contributors to the X window software
wrote the paper.

ULTRIX-32m Master Index (Order No. AA-CN36C-TE) allows fast access
to information in the ULTRIX-32m documentation set. Individual indexes
are included in each book.

MicroVMS Software
MicroVMS Release Notes (Latest Version) contains last-minute information
about MicroVMS. You may order the entire MicroVMS documentation
set as a unit (Order No. 00-QZ001-GZ-4.4).

MicroVMS User’s Primer (Order No. AAmZZlOCmTE) introduces the MicroVMS operating system to novice users.

MicroVMS User’s Manual (Order No. AA-Z209B-TE) describes the operation of the MicroVMS operating system.

MicroVMS User’s Pocket Reference (Order No. AA-Z211C-TE) summarizes
the DIGITAL Command Language (DCL), EDT editor, DIGITAL Standard
Runoff (DSR), and MAIL commands.
MicroVMS FORTRAN Programmer’s Primer (Order No.

AA-Z213A-TE)

contains concepts of program development using FORTRAN in the MicroVMS environment.

MicroVMS FORTRAN Programmer’s Manual (Order No. AA-Z212B-TE)
contains guidelines for using VAX FORTRAN with MicroVMS tools, such
as run-time library routines, system services, the debugger, and relevant
utilities. The manual presents a task-oriented approach to programming
with FORTRAN on a MicroVMS system. Specifications for VAX FORTRAN statements are included in an appendix.

MicroVMS Programming Support Manual (Order No.
AA-DC87B-TE)
contains the specifications for the following MicroVMS programming
support tools: the run-time library routines, system services, terminal
and mailbox I/O function codes, debugger, linker, file definition language,
message utility, command definition utility, and condition codes.

B—4

VAXstation |I/GPX Owner's Manual, BA123 Enclosure

MicroVMS Programming Pocket Reference (Order No. AA-Z214B-TE) contains syntax specifications for the following programming tools: run-time
library routines, system services, debugger commands, and relevant DCL
commands. The pocket reference also includes a summary for dot notation.

MicroVMS Workstation User’s Guide (Order No. AA-EZ24C-TN) describes
the installation and use of the MicroVMS workstation software. You may
order the entire MicroVMS workstation documentation set as a unit (Order
No. 00-Q4A96-GZ-3.0).
MicroVMS Workstation Graphics Programming Guide (Order No.

AL-

GL10B-TN) provides a tutorial and a reference to the MicroVMS workstation graphics programming interface.

MicroVMS Workstation Video Device Driver Manual (Order No.

AADY65D-TE) contains information about device drivers for programmers.
The section on the VCB02 (QDSS) applies to the VAXstation II/GPX.

VAXstation Il/GPX Related Documents

B—5

Glossary
application program

A program designed to perform a task, such as monitoring a manufacturing
process.

ASCII

American Standard Code for Information Interchange. A set of 8-bit binary
numbers representing the alphabet, punctuation, numerals, and other special
symbols used in text representation and communications protocol.
asynchronous multiplexer

A device that provides asynchronous communication and brings together several low-speed communications channels. The device controls and alternates

the transmission of signals with start and stop signals, so that more than one
signal can be transmitted over a single communications line.
backplane

A connector block that connects modules through a bus and provides physical

support of those modules.
back-up copy

A copy of data stored on your disk. The duplicate copy is stored on either
RX50 diskettes or TK50 magnetic tape cartridges.
back-up process

The process of making copies of the data stored on your disk so that you can

recover that data after an accidental loss. You make back-up copies on RX50
diskettes or TK50 magnetic tape cartridges.
baud rate
‘
The speed at which signals are serially transmitted along a communications

line. One baud equals one bit/second.
bezel

A cover used to hold and position the edges of a device.

Glossary-1

binary

A number system that uses 2 digits: 0 and 1. They are represented in system

circuitry by two voltage levels, and the system programs are executed in

binary form.

bit

A binary digit; the smallest unit of information in a binary system of notation,
designated as a 0 or a 1.
bitmap

The type of graphics supported by the VAXstation II/GPX. With bitmap
graphics, the workstation software can individually access each dot (pixel) on

the video screen.
boot

See bootstrap.
bootable medium

A fixed disk, diskette, or magnetic tape cartridge containing software (such
as an operating system), that a bootstrap program can load into the system

memory and begin program execution.
bootstrap

A program that you start when you turn on the system. The bootstrap

loads software contained on fixed disk, diskette, or magnetic tape car-

tridge into memory; the system stops executing the bootstrap and starts
executing the software in memory. The software usually loads an oper-

~ ating system or other software into memory so that the system can start
processing.

To use a bootstrap program.

bus

A printed circuit module that is part of the backplane. The bus permits the
sharing of signals among the system modules.

byte

A group of eight binary digits (bits). A byte is one-quarter of the size of a
system word.

Glossary-2

Central Processing Unit (CPU)
The part of the system that controls the interpretation am,d execution of
instructions. In the VAXstation II/GPX system, CPU functions are contained
on one MicroVAX II CPU chip.
command

An order you can give to the system, often through a terminal keyboard.
communications line

A cable along which electrical signals are transmitted. Devices or systems that
are connected by a communications line can share information and resources.
computer system

A combination of system hardware, software, and external devices that performs operations or tasks.
console mode

The stage at which a device can communicate directly with the CPU. For the
VAXstation II/GPX, console modeis activated by pressing the halt pushbutton
when the Halt Enable/Disable switch is enabled (up) and is indicated by
the arrow prompt (>>>) on the system monitor.
controller

A system component, usually a printed circuit module, that regulates the
operation of one or more peripheral devices. Controllers are often called
interface units.
control panel

The panel on the front of the system cabinet that contains control switches
and indicator lights.
CPU

Abbreviation for Central Processing Unit. See Central Processing Unit.
CRT (Cathode Ray Tube)

A vacuum tube that generates and guides electrons onto a fluorescent screen

to produce characters or graphics. A term often used to refer to a monitor.
data

A representation of facts, concepts, or instructions in a formalized manner
suitable for communication, interpretation, or processing by humans or by
automatic means.

Glossary-3

data transmission

The movement of data in the form of electrical signals along a communications
line.
debug

To detect, locate, and correct errors (bugs) in system hardware or software.
DECnet

DIGITAL communication network.
device

The general name for any unit connected to the system that is capable of
receiving, storing, or transmitting data. See input device, output device, Input/
Output device, and controller.
device name

The name by which a device or controller is identified in the system. You
use that name to refer to that device when you are communicating with the
system.

diagnostic medium

Diskette or tape that contains diagnostics. See diagnostics.
diagnostics

A program that detects and identifies abnormal system hardware operation.
The VAXstation II/GPX “Maintenance System” software contains several diagnostic programs.
disk

A flat circular plate with a coating on which data is magnetically stored in

concentric circles (tracks). The VAXstation II/GPX contains at least one fixed
disk, either the RD53 or RD54 disk drive subsystems, or both.
disk drive

A device that holds a fixed disk. The drive contains mechanical components
that spin the disk and move the read/write heads that store and read information on the surface of the disk. The VAXstation II/GPX disk drive can
read and write on the RD53 and RD54 fixed disks.
disk drive subsystem

A free-standing disk drive that provides additional storage for the system.
The RD53 and RD54 are disk drive subsystems that can be added to the
VAXstation II/GPX.

Glossary-4

diskette

A flexible, floppy disk contained in a square paper envelope. The VAXstation
I1/GPX uses the RX50 13.13-centimeter (5.25-inch) diskettes.

diskette drive

A disk drive that only reads or writes on removable diskettes. The VAXstation
II/GPX diskette drive uses RX50 diskettes.

A method of generating characters for printing that uses dots to produce
readable characters.
down-line load

To send a copy of a system image or other file over a line to the memory of
a target node.
error message

A message displayed by the system to indicate a mistake or malfunction.
file

A collection of related information treated by the system as a single item.
formatted data

A pattern of data that conforms to a predetermined structure dictated by the
system software.
- GKS

Graphics Kernel System. GKS acts as one of the graphics interface for the
VAXstation 1I/GPX.

GPX

Graphics Processing Extension.
hard-copy terminal

A terminal that displays information on paper. Compare to video terminal.

hardware

The physical components—mechanical and electrical—that make up a system.

Compare to software.
head

The part of a fixed disk drive, diskette drive, or tape drive that reads, records,

and erases data. Also called read/write head.

Glossary-5

host

The primary or controlling computer in a multiple computer network.
input device

A piece of equipment that is used to transfer data to the system. For example,
a keyboard is an input device.

Input/Output (I/0) device

A piece of equipment that accepts data for transmission to (input) and from
(output) the system. For example, a terminal.
interactive

The method of communicating with the system. You type a command at the
keyboard. The system executes the command and responds with a prompt
character for another command.
interface

A device or piece of software that allows the components of the system to
communicate,
/0

Abbreviation for Input/Output. See Input/Output (I/0) device.
K

The symbol that means 2 to the 10th power (or 1024 in decimal notation).
kilobyte

1000 bytes.
LED

Light-Emitting Diode. LEDs are used as indicators on the control panel. A
segmented LED display on the CPU distribution panel insert on the back of
the VAXstation II/GPX cabinet displays the characters F-A and 8-0 during the
power-on sequence to indicate CPU status and normal/abnormal operation.
load

To move software (usually from a peripheral device) to memory.

To physically place a disk on a disk drive or a tape on a tape drive.

Glossary-6

Local Area Network (LAN)

A data communications system designed for a small geographic area that offers
hxghwspeed communications channels optimized for connecting information
processing equipment. For example, Ethernet.

The symbol for 1024 squared (1,048,576 in decimal notation).

magnotid tape

A strip of plastic coated with magnetic oxide and used for storing data. Often
called magtape.
megabyte

1,000,000 bytes.
memory

The area of the system that holds the instructions and data that temporarily
store information.
memory module

A logic circuit module that contains additional memory for the system. Two
memory modules with 1, 2, or 4 megabytes of memory can be added to the
VAXstation I1/GPX.
menu

A displayed list of options that you can select to run.
MicroVAX Workstation

Any workstation based on the 32-bit MicroVAX CPU. The workstations
include the MicroVAX and the VAXstation systems.

MicrovMS
A micro version of the VAX/VMS operating system for MicroVAX-based
systems. MicroVMS enables installation of only those parts of the VMS
operating system you require, but will allow access to all VMS operations.

MicroVMS Workstation Software

Window management software for a MicroVAX-based system.
must run MicroVMS as the operating system.

The system

Workstation software allows

you to control and view several programs on one screen.
window with which to interact by using a pointing device.

You specify the

Glossary-7

module

A printed circuit board. The module contains chips, electrical components,
and electrically conductive pathways between components. A module stores
data or memory, or controls the functions of a device.
mouse

A relative-positioning input device that is rolled across the desktop to move
the cursor on the monitor screen, and is used to select menu options and
draw graphics. The mouse is palm-sized, contains three pushbuttons (function
keys), and a ball bearing. The mouse is a pointing device for the VAXstation
II/GPX.
network

A group of individual computer systems that are connected by communications lines to share information and resources.
node

An individual information-processing unit, such as a computer, workstation,
or peripheral device, that is connected to a network.

off-line

Pertaining to equipment, devices, and events that are not controlled by the
system.

on-line

Pertaining to equipment, devices, and events that communicate with. the

system.

operating system

A collection of system programs that control the operation of the system and
perform such tasks as assigning memory to programs and data, processing
requests, scheduling jobs, and controlling the operation of input and output
devices.
output device

A device that extracts data from the system. A printer is an example of an
output device.
peripheral device

A device that provides the CPU with additional memory storage or commu-

nication capability. Examples are disk and diskette drives, video terminals,
and printers.

Glossary-8

plane

Measures 1K x 1K x 2K and holds a total of 256K memory.

pointing dbvica
A terminal input device that allows you to make a selection from a menu or
to draw graphics. See mouse, puck, stylus, and tablet.
power-up sequence (power up)

A series of ordered events that occur when you supply power by turning on

the system.
printer

A peripheral device that provides paper copies of information stored on the
system.
program

The sequence of instructions the system needs to perform a task. See software.
prompt

Words or characters that the system displays to indicate that it is waiting for
you to type a command.

puck

A flat, rectangular, 4-pushbutton pointing device included with the tablet,

which moves the cursor on the monitor screen, draws graphics, and makes
selections from the menu. See also tablet.
RAM

Abbreviation for Random-Access Memory. See Random-Access Memory (RAM).
Random-Access Memory (RAM)

Memory that can be both read and written into during normal operations.

The type of memory the system uses to store the instructions of programs
currently being run.
raster

A linear measurement unit for graphics characters.
Read-Only Memory (ROM)

A memory whose contents cannot be modified. The system can use the data
contained in a ROM but cannot change it.

Glossary-9

reboot

To restart the system. Pressing the Restart pushbutton on the control panel
reboots the VAXstation II/GPX system, if the Halt Enable/Disable switch
on the back of the VAXstation II/GPX cabinet is in the up (enable) position.
ROM

Abbreviation for Read-Only Memory. See Read-Only Memory (ROM).
run

A single continuous execution of a program.

To execute a program.

software

Programs executed by the system to perform a chosen or required function.
Compare to hardware.
storage medium

Any device capable of recording information, for example, a diskette.
store

To enter data into a storage device, such as a disk, or into memory.
stylus

A stencil-shaped pointing device included with the tablet, which moves the

cursor on the monitor screen, draws graphics, and makes selections from the
menu. See also tablet.
synchronous line controller

A device that provides high-speed synchronous communication for distributed
networks. Three varieties of the DMV11 are optional synchronous line
controllers for the VAXstation I1/GPX.
system

A combination of system hardware, software, and peripheral devices that
performs specific processing operations.
system image

The image that is read into memory from disk when the system is started up
(booted).

Glossary-10

system management tasks
Tasks performed by the operating system and used to control the operation
of the system.
tablet

An absolute-positioning input device comprised of a flat-surfaced digitizing
tablet, a puck, and a stylus. The tablet is a drawing surface used with the

puck or stylus as a pointing device to move the cursor on the monitor screen,

and to draw graphics and make selections from the menu. The tablet may
be used with the VAXstation II/GPX.
tape drive

A device that contains mechanical components and holds, tns, reads, and

writes on magnetic tape. The VAXstation II/GPX uses the TK50 tape drive.

Tektronix® 4014
A storage-tube display terminal sold by Tektronix, Inc.
terminal

An Input/Output device that allows you to communicate with the system.
Terminals are divided into two categories: video and hard-copy.
32-bit length

The length of the internal data path of the CPU. This length provides more
concentrated data, allows more data types, and enables more data to be
transferred at one time than a 16-bit internal data path.
ULTRIX-32m

ULTRIX-32m is an interactive, time-sharing operating system derived from

UNIX® and enhanced by DIGITAL to work with MicroVAX hardware and
software.

ULTRIX-32w

The window management software for a MicroVAX-based system. The system

must run ULTRIX-32m as the operating system. Workstation software allows
you to control and view several programs on one screen. You specify the

window with which to interact by using a pointing device.
vCB02

A video subsystem that provides 1024 x 864 pixel resolution on a 47.5centimeter (19-inch) color monitor. The 4-plane subsystem simultaneously

displays 16 colors, while the 8-plane subsystem simultaneously displays 256

colors.

Glossary-11

video terminal

A terminal that displays information on the screen of a cathode ray tube
(CRT). Compare to hard-copy terminal.
VLSI

Very Large Scale Integration of integrated circuit chips. A large number of
chips can fit on a printed circuit module; therefore fewer modules are needed,
and the system can be smaller.
VT100 terminal

An American National Standards Institute (ANSI)-compatible terminal offered
|

by DIGITAL.
Winchester disk

A hard disk permanently sealed in a drive unit to prevent contaminants from
affecting the read /write head. The sealed Head/Disk Assembly (HDA) helps
to increase drive reliability and ensure data integrity.
window

An area on your monitor screen in which you can start, run, and view a
separate process. Windowing is supported by both MicroVMS and ULTRIX
workstation software.
word

The largest number of bits (32) that the VAXstation II/GPX can handle in an
operation. The VAXstation II/GPX can also handle longwords (that is, two
words or 64 bits).
write-protect

To protect a disk, diskette, or other storage medium from the addition,
revision, or deletion of information.
write-protect notch

The small notch on the side of an RX50 diskette that you can cover with
an adhesive-backed foil label or tab to prevent loss of data by accidental
overwriting.
write-protect switch

The switch that you slide down on a TK50 tape cartridge to prevent loss of
data by accidental overwriting.

Glossary-12

Index
A

DEQNA (cont’d.)

Accessories kit
components, 1-2

Asynchronous multiplexers
description, 4-23, 4-24

installation, 4-23, 4-24

installation, 4-18

DESTA
determining need for, 4-19
See DIGITAL ThinWire Ethernet

Station Adapter, 4-21
DF112 modem

description, 4-22
option, 4-22

Barrel connector

DF124 modem

description of, 4-20

description, 4-22

determining need for, 4-19

option, 4-22

BNE3x cable

DF224 modem

lengths, 4-19

description, 4-22

types, 4-18

option, 4-22

DHV11

description, 4-24

Color monitor

specifications, A-2

Communication modules
description, 4-18

Connector
determining need for, 4-19

Connectors

list of, 4-20
Consolidation carton
components, 1-2

Controller
storage devices, 4-16

installation, 4-24
Diagnostics

configuration and devices display,
5-18
exiting diagnostics, 5-18

field service menu, 5-18
initial display, 3-10
initial testing, 2-25
introductory display, 2-30
maintenance system, 5-17
maintenance system main menu,

5-17

mode switch, 2-32
power-up messages, 5-1

RX50 diskette insertion, 2-28

DELNI

description, 4-18
installation, 2-20
DEQNA
description, 4-18

setting date and time, 2-30
system utilities menu, 5-18

testing with the RX50 diskette,
2-27
testing with the TK50, 2-25

Index—1

Diagnostics (cont’d.)

testing with the TK50, 2-25
test screen, 2-33
TK50 tape, 2-25
TK50 tape insertion, 2-27
DIGITAL ThinWire Ethernet Multiport
Repeater, 4-20

F
Fixed disk drive, RD53
specifications, A-7

Fixed disk drive, RD54

specifications, A-8
Fonts

LA210, 4-6

DIGITAL ThinWire Ethernet Station
Adapter, 4-21
features of, 4-21

ports of, 4-21

DIGITAL ThinWire Ethernet Station
Adapter, definition, 4-21
Disk drive, fixed
description, 3-13

location, 3-13
Diskette
back-up, 3-24
description, 3-19

drive, 3-20
handling, 3-23
insertion, 3-22
labeled, 3-21
overwrite protection, 3-23

storage, 3-23
Diskette drive, RX50
Specifications, A-8
DMV11

description, 4-24

LCGO1, 4-9
LNO03, 4-2
Front control panel
controls and indicators, 3-1
DC OK indicator, 3-5
fixed disk pushbuttons, 3-8
halt pushbutton, 3-6
power switch, 3-4
Restart/Run pushbutton, 3-5
Fuse

replacing, 5-10

H
H4000

installation, 4-18
Hardware support kit
components, 1-2

Input devices
mouse, 4-14

installation, 4-26

tablet, 4-13

Documentation

hardware, 1-2, B-1
MicroVMS, B-4
ULTRIX, B-2
DPV11

description, 4-26
installation, 4-26
DZQ11

description, 4-23
installation, 4-23

K
Keyboard

cable assembly connection, 2-7
installation, 2-7
KMV11
description, 4-27
installation, 4-27

L
LA210

Environment

system, 1-6

Index—2

description, 4-6
installation, 4-6, 4-12

LA210 (cont’d.)

Memory module
description, 4-14

picture of, 4-6

installation, 4-14

LAS50

types, 4-14

description, 4-8

installation, 4-9, 4-12

MicroVAX Diagnostic Monitor

picture of, 4-9

main menu, 5-17
Modems

list, 4-22

installation, 4-12

LA75 printer

Monitor

description, 4-7
option, 4-7

site-preparation, 1-4
Monitor, color

cable assembly connection, 2-5

Labels
placement of, 2-10

front and side controls, 3-11
fuse, 5-10
carrier, 5-11
location, 5-11
keyboard connection, 2-7
placement, 2-3

LCGO01
description, 4-9
installation, 4-10
LCPO1

installation, 4-12

power cord, 2-14, 2-17

LNO03

description, 4-2

power switch, 2-2

installation, 4-3, 4-12

power up, 2-24

picture of, 4-3
LNO03 PLUS
installation, 4-12
LNO03 PLUS printer
description, 4-3

rear controls and connectors, 3-12

specifications, 1-5, A-2
system unit connection, 2-13

troubleshooting procedures, 5-8
Mouse, 4-14

option, 4-3

cover plate, 5-13

LPS40 printer

installation, 2-8

description, 4-4
option, 4-4
LVP16

description, 4-10
installation, 4-10, 4-12

M
M7168

description, 4-15
installation, 4-15
M7169

maintenance, 5-13

schedule, 5-13
specifications, A-4
use of, xii
MS630
description, 4-14
installation, 4-14

O
Option
DMYV11 synchronous line

controller, 4-24

description, 4-15
Maintenance System
options, 5-17
MDM, 5-17

Options
DEQNA communications module,
4-18

Index-3

Options (cont’d.)

Pointing device

DHV11 asynchronous multiplexer,
4-24

installation, 2-8
Power requirements

DPV11 synchronous line controller,

4-26

system, 1-5

Power up

DZQ11 asynchronous multiplexer,

messages, 5-1

4-23

KMV11 programmable controller,

troubleshooting procedures, 5-3
Printers

4-27

connection to VAXstation I1/GPX,

LA210, 4-6

4-11

LA50, 4-8

LA210, 4-6

LA75 printer, 4-7

LA50, 4-8

LCGO1, 4-9
list of, 4-1

LA75, 4-7

LNO03, 4-2

LNO3, 4-2

LNO3 PLUS printer, 4-3

LNO3 PLUS, 4-3

LVP16, 4-10

system unit connection, 4-12

LCGO1, 4-9

maintenance system main menu,

5-17

types, 4-2

PrintServer 40 (LPS40)

memory modules, 4-14

description, 4-4

modems, 4-22

option, 4-4

mouse, 4-14

MS630, 4-14
4-plane module, 4-15

8-planes, 4-15

RD53 fixed disk drive

description, 4-16

printers, 4-2

PrintServer 40 (LPS40) printer, 4-4

RD53 fixed disk drive, 4-16

specifications, A-7
RD54 fixed disk drive

description, 4-16

RD54 fixed disk drive, 4-16
RX50 Dual Diskette Drive, 4-17
tablet, 4-13
TK50 Tape Drive, 4-17

specifications, A-8
Read and Write Errors

troubleshooting procedures, 5-6
RQDX3, 4-16
RQDX3 controller, 4-16

RX50, 4-16

4-plane Module
description, 4-15
installation, 4-15

8-Planes
description, 4-15

Plotter
LVP16, 4-10
Pointing Device

troubleshooting, 5-10

Index—4

description, 4-17
installation, 4-17
specifications, A-8

Service
procedures, 6-1

Shipment components
listing, 1-1

Site-preparation

Tape

environment, 1-6

back-up, 3-24
description, 3-13
drive, 4-17, 5-7

power requirements, 1-5

space planning, 1-3
Software carton

drive specifications, A-9

components, 1-2

handling, 3-19

Storage device option package, 4-16

insertion, 3-14

Synchronous line controlleres

overwrite protection, 3-18

description, 4-26

storage, 3-19

Synchronous line controllers
description, 4-24

TK50, A-9

T-connector

installation, 4-26
Synchronous lines controllers
installation, 4-26

description of, 4-20

determining need for, 4-19
Terminator

System

description of, 4-20
determining need for, 4-20

connecting the transceiver cable,

2-19
System halts

ThinWire Ethernet
connectors, 4-20

troubleshooting, 5-6

System unit

terminator, 4-20

TK50, 4-16

adjusting baud rate, 2-12
connecting video cable, 2-13

troubleshooting, 5-7
Transceiver

control panel, 2-10, 3-1

definition, 4-21

cover opening, 2-11

Transceiver cable, 4-18, 4-19

CPU distribution panel, 2-12

Troubleshooting

diskette drive, 3-20

basic, 5-2

installation, 2-10

color monitor, 5-8
diskette drive, 5-5

labels, 2-10
physical specifications, 1-4

maintenance system, 5-17

power cord, 2-14, 2-18

power up, 5-1, 5-3

power on/off, 2-16

procedure, 5-1

power requirements, A-1

read and write errors, 5-6

setting controls, 2-12

system halts, 5-6

site-preparation, 1-3

system unit, 5-3

troubleshooting procedures, 5-3
voltage setting, 2-15

TK50 tape drive, 5-7
Two-user system, 4-15

Tablet

VAXstation II/GPX

description, 4-13

carton components, 1-2

installation, 2-8, 4-13

described, xi

specifications, 4-13
specifications, A-5
use of, xii

environmental requirements, 1-6,
A-2
network, 2-19

Index—5

VAXstation II/GPX (cont’d.)
options, xi, 4-1
power requirements, A-1
printer connection, 4-11

service, 6-1

shipment components, 1-2
site-preparation, 1-3

software installation, 2-35
testing, 2-24

troubleshooting, 5-1

turning off, 3-10
turning on, 3-8
VCB02
video subsystem, 4-15
Voltage
system unit setting, 2-15

W
Windows

described, xii

Index—6

HOW TO ORDER
ADDITIONAL DOCUMENTATION

From

Call

Alaska, Hawaii,

603-884-6660

or New Hampshire

Rest of U.S.A.

and Puerto Rico*

Write

Digital Equipment Corporation
|

P.O. Box CS2008

800-258-1710

Nashua, NH 03061

* Prepaid orders from Puerto Rico must be placed with DIGITAL'’s local
subsidiary
(809-754-7575)

Canada

800-267-6219
(for software

documentation)
613-592-5111
(for hardware

Digital Equipment of Canada Ltd.

100 Herzberg Road

Kanata, Ontario, Canada K2K 2A6

Attn: Direct Order desk

documentation)
Internal orders

(for software
documentation)
Internal orders
(for hardware

documentation)

Software Distribution Center (SDC)

Digital Equipment Corporation
Westminster, MA 01473
617-234-4323

Publishing & Circulation Serv.

(P&CS)

NRO03-1/W3
Digital Equipment Corporation
Northboro, MA 01532

VAXstation II/GPX Owner’s Manual,
BA 123 Enclosure
EK-105AA-0OW-001

READ

E S
COMM

R’S

Note: This form is for document comm
ents

ENTS

form at the company’s discretion.

DIGITAL will use comments submitted ononly.
this

Did you find this manual understandable,
usable, and well organized? Please
make suggestions for improvement.
|

Did you find errors in this manual?
number,

If so, specify the error and the page

Please indicate the type of user/reade
NelhS

dministrative Support
omputer Operator

ducator/Trainer

DO0000oo0ogog

r that you most nearly represent:

rogrammer/Analyst

Sales
Scientist/Engineer
Software Support
System Manager
Other (please specify)

Name

Date

Organization

Street

City

State

Zip Code
or Country

——

NO POSTAGE
NECESSARY
IF MAILED
IN THE

UNITED STATES

BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO.33 MAYNARD MASS.
POSTAGE WILL BE PAID BY ADDRESSEE

DIGITAL EQUIPMENT CORPORATION
CORPORATE USER PUBLICATIONS
MLO5-5/E45

146 MAIN STREET

MAYNARD, MA 01754-2571

T T T

}

Along Dotted Line

———— — — —

— | o—

Do Not Tear — Fold Here

——-,-s—s;—s—-;s—-sa—fl