Digital PDFs

EK-0LN03-RM-002

1986

6 pages

Original

0.9MB

view download

OCR Version

0.4MB

view download

Document:	LN03 Programmer Reference Manual
Order Number:	EK-0LN03-RM
Revision:	002
Pages:	6
Original Filename:

OCR Text

TECHNICAL DOCUMENTATION
CHANGE NOTICE

EK-OLNO3-RM-CN1

LNO3 PROGRAMMER REFERENCE MANUAL
EK-OLNO3-RM-002

This notice contains changes and additionstothe LNO3 Programmer Reference

Manual. Update your manual as indicated in the following pages. These

changes apply if Version 4.4 (or higher) firmware is installed in your printer.
PAGE 17

Change the description of pin 20 in Table 2-1, as follows.
From

This line is reserved for future

This line is asserted (high) when

use.

the LNO3 is ready to send or

receive data.

PAGE 22

Add the following note after the second paragraph describing the Autowrap
(SP2-4) switch.
NOTE:

Ifautowrapisnotenabledandyoutrytogobeyondtherightmargin, an

unsolicited error report is sent to the host, provided the unsolicited report is

enabled (Paragraph 5.9.2). This error is only reported to the host; it is not
reported on the indicator panel.

Printed in U.S.A.

digital equipment corporation . maynard, massachusetts

PAGE 63

Add the following note immediately after the example in Paragraph 4.6.2, Font

Status Report (DECFSR).

NOTE:

Referto Appendix D to interpret the 31 character font file ID for type

family, font, and character set.
PAGE

Add the follbwing note to the end of Paragraph 5.2.3, AutoWrap Mode
(DECAWM).
NOTE:

|
.

—

|Ifautowrapisnotenabledandyoutrytogobeyondtherightmargin,an

unsolicited error report is sent to the host, provided the unsolicited report is

enabled (Paragraph 5.9.2). The error is only reported to the host; it is not
reported on the indicator panel.

PAGE 76

Changethe third sentence ofthe notein Paragraph 5.3, Select Size Unit(SSU),
as follows.
From
The printer converts 1 decipont to O pixels and 2 decipoints to 1 pixel.
To
B

The printer converts 1 decipoint to 1 pixel and also converts 2 decipoints to 1

pixel.

PAGE 102

Add the following note to the Paragraph 5.6, Active Column and Active Line,
immediately following the listing of horizontal sequences.

NOTE: |If the underline, strike through, or fallback for italics (underline)
attribute is in effect when you issue an HPA, HPR, or HPB sequence, then

underline or strike through is imaged according to the movement commanded

by the horizontal sequence.

For example, if the underline attribute is in effect and the active position is
moved from the center of a line backwards (HPB sequence), then everything
from the center to the backward position is underlined.
PAGE 103

Change the note in Paragraph 5.6.2, Horizontal Position Relative (HPR) as
follows.
From

NOTE:

Ifyou selectdecipoints andsendthe HPR sequence with a Pnvalue of

1, the active position will not move. The printer converts 1 decipoint to 0 pixels.
(See Paragraph 5.3.)
To

NOTE:

Ifyouselectdecipoints andsendthe HPR sequence with a Pn value of

1, the active position will move 1 pixel. The printer converts 1 decipoint to 1
pixel. (See Paragraph 5.3.)

PAGE 105
Change the first paragraph of the note in Paragraph 5.6.5, Vertical Position
Relative (VPR), as follows.
From

NOTE:

If you select decipoints and send the vertical position relative

sequence with a Pn value of 1, the active position will not move. The printer
converts 1 decipoint to 0 pixels. (See Paragraph 5.3.)
To

NOTE:

|If you select decipoints and send the vertical position relative

sequence with a Pn value of 1, the active position will move 1 pixel. The printer

converts 1 decipoint to 1 pixel. (See Paragraph 5.3.)
O

PAGE 114
Add the following error code to the specific controller error codes listed in

Table 5-6.
Pn

Error

115

Character lost, right margin exceeded.
S,

—

OGS