Digital PDFs

EJ-002AB-IG-2

September 1987

311 pages

Original

8.8MB

view download

OCR Version

8.1MB

view download

Document:	MicroVAX II 630QY, 6300QZ installation
Order Number:	EJ-002AB-IG
Revision:	2
Pages:	311
Original Filename:

OCR Text

Contents
Installation

Operation
Troubleshooting
Technical Information

Site Preparation
Notes

Services

MicroVAX1i630QY, 63002z
Iinstallation
Order Number EK-002AB-1G-002

digital equipment corporation

maynard, massachusetts

December 1986
September 1987

The information in this document is subject to change without notice and should not be construed as a
commitment by Digital Equipment Corporation.

Digital Equipment Corporation assumes no responsibility for any errors that may appear in this document.

The software, if any, described in this document is furnished under a license and may be used or copied only
in accordance with the terms of such license. No responsibility is assumed for the use or reliability of software
or equipment that is not supplied by Digital Equipment Corporation or its affiliated companies.
Copyright ©1986, 1987 by Digital Equipment Corporation.
All Rights Reserved.
Printed in U.S.A.

The READER’'S COMMENTS form on the last page of this document requests the user’s critical evaluation to

assist in preparing future documentation.

The following are trademarks of Digital Equipment Corporation:

COMPACTape

MASSBUS

ThinWire

DEC

MicroVAX

ULTRIX

DECmate

PDP

UNIBUS

DECnet

P/OS

VAX

DECUS

Professional

VAXcluster

DECwriter

Q-bus

VAXELN

DELNI
DEQNA

Rainbow
RSTS
RSX

VMS
VT
Work Processor

DESTA

dilgli tall ly
ML-5809

FCC NOTICE: The equipment described in this manual generates, uses, and may emit radio frequency
energy. The equipment has been type tested and found to comply with the limits for a Class A computing
device pursuant to Subpart ] of Part 15 of FCC Rules, which are designed to provide reasonable protection
against such radio frequency interference when operated in a commercial environment. Operation of this
equipment in a residential area may cause interference, in which case the user at his own expense may be
required to take measures to correct the interference.

Contents
Preface ...........

----------------------------

Verify Site Preparation . . . .. ............
... ...
Check Your Shipment.

... ....................

Place the System

Install the Console Terminal . . . ... .............

Connect the Console Terminal to the System

. ... ..

Connect Additional Devices to the System ........
6.1

Connect Terminals and Printers . . . .. .............

6.2

Connect Modems to the System . . . ...............

Connecttoa Network . .. .........
... ... .. ... ...

6.3

Set Controls on Your System

. .................

7.1

Set Controls on the CPU Panel . . ... ... ..........

7.2

Check the Voltage Setting . . . .. .................

Check the Circuit Breaker . . . .. ... ... ... .. .. ....

7.3
A

/.4

Label and Set Controls on the Control Panel

.........

Connect the System Power Cable . .. ............

Turn On the System and Select a Language.

. . . . . ..

Attach the Rear Panel to the System . . . ... .......

After Installation

Appendix A

Tabletop Conversion Procedures

Appendix B

Rack Mount Instructions

System Air Flow

Console Terminals for MicroVAX II Systems . . . . .. ... ...

Removing the Rear Cover

Connecting the Console Terminal to the System . .. ... ...

Connecting Additional Devices

Connecting an Ethernet Cable to the System

... ........

CPU Panel Controls . .. ....... .. ..... . ... ... ...,

Checking or Changing the Voltage Setting . . . .. ... ... ..

Checking the Circuit Breaker.

. . .. ..............
...

Labeling the Control Panel . . . .. . .................

PowerCords . . ....... ...

. .. .................

. . .

Attaching Power Cord to the System

Language Selection Menu.

Successful Power-On. .. .

. ...............

... ... ..............
...

...

... ... ..

=
N

. ... ...................

. ..............
... . ... . ...,

Shipping Carton Contents

. ... ...................

Figures

18
19
20

Preface
This manual describes how to install the MicroVAX 1I 630QY, 630QZ system.
manual describes how to install the 630QY variant, the
The main body of the
pedestal mount Apperdix A describes l"mw to convert the pedestal mount
to a tabletop model. Appendix B describes how to rack mount the 630QZ
variant.

Installation includes the following steps:

Placing the system

Installing the console terminal

Connecting the console terminal to the system

Checking your shipment

Connecting other devices to the system

Setting controls on the system

Verifying site preparation

Connecting the power cord

Turning on the system and selecting a language

If you prefer not to install the system, DIGITAL provides an installation
service.

1 Verify Site Preparation
Prior to receiving your system, you should have received a Micro Systems
Site Preparation Guide. This guide describes the physical, environmental,
and electrical requirements to operate your system. For your convenience, a
copy of this guide is also included in your Customer Hardware Information
kit. If you have not already done so, please read the guide and follow its
instructions for preparing your site.

The installation instructions that follow assume that the site meets all
the requirements listed in the Micro Systems Site Preparation Guide. The
instructions also assume that all terminal data lines, telephone lines, and
network lines that you plan to connect to your system are in place and
clearly labeled.

2 Check Your Shipment
Your shipment includes several cartons. Before installing your system, unpack
all boxes and check the contents against the shipping list to ensure you have
received everything you ordered.
NOTE: Save all packing materials if you plan to reship the system.
If any item is missing or damaged:

Contact your delivery agent.

Contact your DIGITAL sales representative.

Instructions for unpacking the system are on the shipping carton.

Figure 1

shows the contents of the shipping carton.

MicroVAX Il 630QY, 6300Z Instaliation

Figure 1:

Shipping Carton Contents

SYSTEM UNIT

TERMINAL CABLE

% 2 SCREWDRIVERS

—

LABEL SHEETS

;—E,;l;
~~~~~~~~ ~

OC0CAGERET
OCOCOC00

GRANT CONTINUITY
MODULE

PLUS OTHER ITEMS

NOT REQUIRED FOR
THIS INSTALLATION

POWER CABLE

MLO-1336-87

NOTE: If you ordered the 630QZ variant, you should receive a rack mount kit.
Refer to Appendix B for instructions on installing the rack mount version of the
MicroVAX II system.

A box marked “Software” contains system software, software documentation,
diagnostic software, and a software license.

Depending on your order, your shipment may include some of the following
equipment:

Additional terminal(s)
Printer(s)

Modem(s)

Cables for connecting additional devices to your system.

MicroVAX 1l 630QY, 63007 Installation

3 Place the System
The installation instructions that follow assume you have correctly followed
the unpacking instructions on the carton. They also assume you are installing
the 630QY pedestal mount.

If you are converting the 630QY system to a

tabletop mount, substitute the instructions in Appendix A for this section.

If you are rack mounting a 630QZ system, substitute the instructions in
Appendix B for this section.
A ffnm 11vmenan 1.3

L2LLCE

rOY

ullya\,l\lllg _yuul

TrAIIR

OTIQ

Dyb

2 TR o a )

WARNING: Use two people to move the unit. The unit weighs 27 kg (60 1b).
Your system requires two inches clearance for ventilation on each side.

Figure 2 shows the air flow through the system.

Figure 2:

System Air Flow

MLO-1397-87

MicroVAX (I 630QY, 63007 Installaton

Your system requires no rear ventilation space. However, during installation
you should leave about two feet at the rear of the system.

You need this
space to connect cables, and to access the controls behind the rear cover.

4 Install the Console Terminal
The first step in installing your MicroVAX 630QY, 630QZ system is to set
up the console terminal. You use the console terminal to communicate with
your system. Your console terminal is packed in several boxes containing the
following;:
*

Video monitor

Keyboard

Documentation, including an installation guide and owner’s manual.

System box (graphics terminals only)

Unpack the terminal and documentation. Some typical console terminals are
shown in Figure 3.

Figure 3:

Console Terminals for MicroVAX |l Systems

MLO-1398-37

MicroVAX 1l 630QY, 63007 Installation

Use the instructions in the terminal installation guide to connect the various
components of your terminal.

Read the terminal owner’s manual to learn how to turn on and operate
the terminal. Before you connect the console terminal to your MicroVAX II
system, turn on the terminal to make sure it works correctly and to perform
some set-up operations.

The terminal performs a self-test every time you turn it on. The terminal
owner’s manual describes a successful self-test and possible error messages

that display if the terminal is not operating properly. Once the terminal

passes the test, you should perform some set-up operations.

Set-up involves choosing how your terminal operates. You choose set-up

options from a series of menus that display when you press the [Set-Up] key on

the terminal keyboard. Details about how to perform set-up and the set-up
options available on your terminal are in your terminal owner’s manual.
While most default settings are acceptable, you should perform the foliowing
procedure to ensure appropriate set-up values.

1. Press

to display the Set-Up Directory Screen. Choose the Default

option. Default correctly sets all values except line speed.

Choose the Comm option to display the Communications Set-Up Menu.
Choose the Transmit option and change the speed to 9600. Set Receive
equal to Transmit.

3. Choose the Return to Set-Up Directory option. Choose the Save Set-Up
option to store the set-up values.

Once you have tested your console terminal and performed set-up operations,
you are ready to connect the terminal to your MicroVAX II system.

MicroVAX 1l 630QY, 63007 Instaliation

5 Connect the Console Terminal to the System
You connect the console terminal to the CPU panel in the rear of the system.
Connect the console terminal to your MicroVAX II system as follows:
1.

Remove the rear cover of your system, as shown in Figure 4.

Figure 4:

Removing the Rear Cover

MLO-1398-87

MicroVAX Il 830QY, 6300Z Installation

Turn off the console terminal.
Find the terminal cable in the accessories box.

Connect the terminal cable to the Comm Port on the rear of your terminal,
according to the instructions in your terminal installation guide.

The

6}]

location of the plug varies with the type of terminal.

Connect the other end of the cable to the CPU panel on the rear of the
T

system, as shown in Figure 5.

DIGITAL’s VT300-series terminals are factory set to accept an RS-232 CPU
panel-to-console terminal connection.

If you have a VT300-series terminal,

and you are plugging the terminal cable into a modified modular jack
(MM]) on the rear of your VT300-series terminal, you are forming a DEC
423 connection.

To make the system recognize your VT300-series console

terminal, you must perform the following Set-Up operations:

Press [SetUp] to display the Set-Up Directory Screen.
When the Set-Up menu appears on the screen, enter Global Set-Up.

Select the Feature “Comm1 Port”.

Change the setting from RS-232 to DEC 423.
Choose the

Return to Set-Up Directory option. Choose the Save Set-Up
IS

option to store the set-up

value.

You are now ready to connect additional devices to your system.

MicroVAX Il 630QY, 63007 Installation

Figure 5:

Connecting the Console Terminal to the System

LA120

(REAR VIEW)
VT240

LA100
(REAR VIEW)

VT220
(REAR VIEW)

(REAR VIEW)
-

MLO-1400-87

MicroVAX 1l 630QY, 63007 Installation

6 Connect Additional Devices to the System
You can connect additional devices to your system, or you can complete
installation and load system software before connecting other devices. Skip
to the next step if you prefer to connect additional devices later. Use the
instructions in this step when you are ready to connect the devices.
Before connecting devices to the system, install and test them according to
the documentation provided with the device.
WARNING: Turn off the devices before connecting them to the system.

You make all connections to the insert panels, on the back of the system.
Internal cabling runs from the connectors on the insert panels to the option
modules.

6.1 Connect Terminails aind Printeis
You can connect up to eight terminals and/or printers to your system for
each DHQ11 and DHV11 module, and four for each DZQ11 module installed
in your system. If the site has been prepared properly, the lines for the
additional terminals and printer(s) are clearly labeled, and terminate near the
system.

MicroVAX 1l 630QY, 63007 Installation

Figure 6:

Connecting Additional Devices

ADDITIONAL
DEVICES

CABLE
GUIDE
MLO-1401-87

After making connections, thread all cables through the lower cable guide,
shown in Figure 6.

6.2 Connect Modems to the System
You connect modem lines to the insert panels the same way you connect

terminals and printers.

The DHQ11, DHV11, and DZQ11 modules have

modem control support.

Connect the other end of the cable to the modem, as described in the modem
installation guide.

Make sure the modem is plugged into a power source

and connected to an active phone jack.

See your modem user’s guide for

instructions on how to use your modem.

6.3 Connect to a Network
You can connect your system to a network if your system has the DELQA

or DEQNA option and if the Ethernet cabling is in place.
connection as follows.

MicroVAX 1l 630QY, 63007 Installation

Make a network

Find the Ethernet transceiver cable shipped with your system. The cable
has a male connector at one end and a female connector at the other end.

Connect the male end of the cable to an Ethernet connector on one of
the smaller insert panels, as shown in Figure 7. Slide up the locking
device on the female connector to secure the connection.

Connecting an Ethernet Cable to the System

Figure 7:

CABLE
GUIDE

MLO-1402-87

Connect the other end of the cable to one of the following devices:

An H4000 transceiver located on a traditional baseband Ethernet cable

A DELNI, which can, in turn, be connected to a baseband Ethernet
cable or which can connect up to eight systems in a local area network
(LAN)

A DESTA converter, if you need to connect to a ThinWire network

DIGITAL’s Network and Communications (NaC) publications explain the
types of network connections possible.

MicroVAX 1l 6300QY, 63007 Installation

7 Set Controls on Your System
Controls on the MicroVAX 1I 630QY, 630QZ system are in four locations:

The CPU panel on the rear of the system

The voltage switch on the rear of the system

The circuit breaker in the rear of the system

The control panel in the front of the system

7.1 Set Controls on the CPU Panel
The following controls are located on the CPU panel, shown in Figure 8.

Figure 8:

CPU Panel Controls

BAUD

POWER-UP

SWITCH

RATE

MODE

HALT

ENABLE/DISABLE

SWITCH

CONSOLE

LED

TERMINAL

DISPLAY

CONNECTOR

MLO-1403-87

MicroVAX Il 630QY, 63007 Installation

Halt Enable/Disable Switch.

The factory setting is halt disable (left),

indicated by the dot outside the circle.

Leave the switch set to disable

while you start the system for the first time and run diagnostic software
to test the system. Before you install system software, move the switch
to halt enable (right).
*

Power-Up Mode Switch.

This 3-position rotary switch determines how

the system powers up. The factory setting is Run Mode, indicated by an
arrow.

Move the switch to the Language Inquiry Mode, indicated by a

human profile, before you power up your system the first time.
*

Baud Rate. Rotate the baud rate switch to 9600. You should have already
set your console terminal baud rate to 9600. The system and the console
terminal must be set to the same baud rate to communicate.

7.2 Check the Voltage Setting
Peel back the label covering the switch to see the voltage setting, as shown in
Figure 9. If necessary, change the switch setting to match the voltage source
you are using.

CAUTION: An incorrect voltage switch setting will damage your system.

MicroVAX 1l 630QY, 63007 Installation

Figure 9:

Checking or Changing the Voltage Setting

115V

)

IN N. AMERICA THE

115V

SWITCH IS SET TO

VOLTAGE SWITCH ———e¥
)©
ool

220 V/230 V/240 V
IN OTHER COUNTRIES
THE SWITCH IS SET

TO 230 V. IF NOT,
LOOSEN HOLD DOWN

SCREWS AND SLIDE
SWITCH TO 230 V.

HOLD DOWN

SCREWS

ML0-1404-87

MicroVAX Il 630QY, 63007 Installation

7.3 Check the Circuit Breaker
Because the circuit breaker sometimes trips during shipment,

check the

position of the circuit breaker, as shown in Figure 10.

Figure 10:

Checking the Circuit Breaker

ML 0-1405-87

Press in on the circuit breaker to make sure it is in the proper position.

MicroVAX 1l 630QY, 63007 Installation

195

7.4 Label and Set Controls on the Control Panel
Before you set controls, you must attach the labels provided in the accessories

kit. Select labels for your language. Two sets of labels are provided for each
language: one with the text oriented properly for the pedestal mount as
shown in Figure 11, the other with text oriented properly for the rack or
tabletop mounts described in Appendixes A and B. If your system contains
diskette drives, label them 1 and 2, as shown in Figure 11.
Figure 11:

Labeling the Control Panel

0o0000aon
ooCOo0on

MLO-1406-87

All four buttons on the control panel are 2-position switches that are either

in or out. Make sure that all four buttons are out.

Set the on/off switch above the four buttons to 0 (off).

MicroVAX Il 630QY, 63007 Installation

8 Connect the System Power Cable
Connect the power cable to the system as follows:

Make sure the system on/off switch is set to off (0), and that all devices
connected to the system are turned off.

Find the power cable packed inside the system shipping carton.

Make sure the pronged end of the power cable plug matches the wall
outlet. Several
are
A RS T oA in Figure 12.
N shown
}rp\—u AL
e ¥V Wl il tvpes

Figure 12:

Power Cords

118V

POWER CABLE

220 V/230 V/240 V

MLO-1407-87

MicroVAX Il 630QY, 63007 Installation

Connect the opposite end of the power cable to the system, as shown in
Figure 13.

Plug the pronged end of the power cable into a wall outlet.

Figure 13:

Attaching Power Cord to the System

MLD-1408-87

MicroVAX Il 630QY, 63007 Installation

9 Turn On the System and Select a Language
You are now ready to turn on your system and select a language. The
language you select controls only the language of the console program. The
console program enables you to give commands to the system and also
generates error messages. The console program is described in MicroVAX 11
630QY, 630QZ Technical Information.
Turn on your system and select a language as follows:
1.

Turnon your consoie terminal and wait until it has Pc1f rmed its self-tes
successfully.

Turn on your system, by setting the on/off switch to 1 (on).

Within a few moments, the Language Selection Menu, shown in Figure 14,
should appear on your console terminal.

Figure 14:

-1

c.rmel

ShA

Language Selection Menu

)

e
1)
2)
3)
4)
5)
6)

Damsk
Deutsch
English
Espaifiol
Frangais
Italiano

7)
8)
9)
10)
11)

Nederlands
Norsk
Portugués
Suomi
Svenska

(1..11):

_/
MLO-1409-87

Select a language by typing the number corresponding to your choice

and pressing [Retur].

MicroVAX 1I 630QY, 63007 Installation

NOTE: If your terminal does not support multiple languages, the language
selection menu does not appear and the system defaults to English.
After you select a language, the system runs power-on self-tests.

Within a

few moments you should see a countdown from 7 through 3 on the console
terminal, as the system completes self-tests.

Figure 15 shows a successful

power-on test.

Figure 15:

Successful Power-On

Performing normal

system tests.

7..6..56..4..3..
Tests completed.

Y,
MLO-1410-87

If the self-tests do not run as shown in Figure 15, your system may have a
problem. Refer to MicroVAX II 630QY, 630QZ Troubleshooting for instructions.

If the self-tests run successfully, turn the Power-Up Mode Switch to the Run
Mode, indicated by an arrow. This saves the language you selected.

MicroVAX Il 630QY, 630QZ Installation

10 Attach the Rear Panel to the System
Reattaching the rear panel is the final step of installation. However, you may
want to wait until after you install system software, since you need access to
the Halt Enable/Disable switch during software installation. When you have
finished installing system software, attach the rear panel. Make sure that all
cables are threaded through the guide at the bottom of the system. Push the
rear panel into place.

11 After Installation
You should now read MicroVAX II 630QY, 630QZ Operation to learn how
to use your system. You must know how to operate the system controls
and the TK50 or TK70 tape drive, or the RX50 diskette drive, before you
install system software or run diagnostic software. Both system software and
diagnostic software are shipped on either tape cartridges or RX50 diskettes.
While optional, DIGITAL recommends that you run the diagnostic software
supplied with your system before you install system software. The diagnostic
software is on several RX50 diskettes labeled MV DIAG CUST RX50 or a
TK50 tape cartridge labeled MV DIAG CUST TK50. Chapter 3 of MicroVAX Il
630QY, 630QZ Troubleshooting describes how to run the diagnostic software.

MicroVAX 1l 630QY, 63007 Installation

Appendix

Tabletop Conversion Procedures
This appendix tells you how to convert the MicroVAX II 630QY system from
the pedestal mount (as shipped by DIGITAL) to a tabletop version. Perform
the conversion as follows:
Remove the front and rear covers.

Install four rubber feet on the right side of the system.

{

J'*A

MLO-1411-87

Tabletop Conversion Procedures

A—1

Remove the four screws at the base of the system.

MLC-1412-87

Lift the system from the foot stand and place it on a table.

WARNING: Use two people to move the system. The system weighs 27 kg

(60 1b).

FOOT
STAND
MLO-1413-87

A—-2

MicroVAX 1l 630QY, 6300Z Installation

Replace the front and rear covers.

MLO-1414-87

Continue wit It the instructions in Section 4.
1

Tabletop Conversion Procedures

A-3

Appendix

Rack Mount Instructions
The following instructions assume installation into a standard cabinet/rack
vallp

Aarsnillaliiie

[

with the following dimensions.
*

48.2 cm (19 in) wide

63.5 cm (25 in) between vertical rails

CUSTOMER

lecoo i TBloco00000000800068,

SUPPLIED
RACK

MLO-1415-87

Rack Mount Instructions

B-—1

WARNING: Installation requires two persons. The rack mount system weighs
27 kg (60 Ib).
Install the system as follows:

Check the contents of the rack mounting kit against the parts shown. If
any item is missing or damaged, call your sales representative.

RAILS (RIGHT, LEFT)
LEF
- 7428371
T - 02
RIGHT - 7428371 - 01

(1 EACH)

FRONT COVER

{1)

RIGHT REAR BRACKET

(1)

7428372- 02

LEFT REAR BRACKET

7428372 - 01

STOP PLATE

NOTE:

7428710 - 01

PHILLIPS HEAD

SCREWDRIVER
REQUIRED

RIGHT FRONT BRACKET

7021543- 01

LEFT FRONT BRACKET

7430071 - 01

0 ¢

\/ NYLON STOP CABLE (1)
—

PHILLIPS MACHINE SCREWS

PHILLIPS SCREW WITH

(13)

o«

o e MACHINE SCREWS

(8)

& PHILLIPS TAP SCREWS

(2)

LOCKING HEX NUT

O @UNUT

WITH LOCK WASHERS
FLAT HEAD PHILLIPS

LOCK WASHER

(1}

{2)

(4)
(12)
MLO-1416-87

B—2

MicroVAX Il 630QY, 630QZ Installation

Prepare right and left rear brackets.

SLIDE U NUTS
IN PLACE

MLO-1417-87

Mount the left and right rear brackets onto the rails.

Use four 10-32

SCrews.
RIGHT REAR
BRACKET

NOTE:

POSITION
LARGER HOLE
TOWARD THE
BOTTOM
RIGHT REAR
RAIL
-

FINGER G@

TIGHTEN

SCREWS

o
=

FINGER
/@NGHTEN

LEFT REAR

BRACKET

§
\

LEFT REAR RAIL
MLO-1418-87

Rack Mount Instructions

B—3

Prepare the rack.
SLIDE U NUTS
IN PLACE

oL
L~

o] TM=
LEFT REAR RACK

LEFT FRONT RACK

Mount the left rail. Use eight 10-32 screws.

LEFT REAR
RAIL

LEFT FRONT
RACK

LEFT REAR RACK

POSITION PREPARED RAIL

AND TIGHTEN ALL SCREWS
ML0-1420-87

B—4

MicroVAX Il 630QY, 630QZ Installation

Repeat steps 4 and 5 to mount the right rails.

Attach the stop plate and front brackets.

Use eight flat head Phillips

machine screws.
STOP PLATE

ATTACH STOP PLATE

ATTACH FASTENERS
AND SECURE FRONT
BRACKETS TO THE

RIGHT FRONT

BRACKET

LEFT FRONT BRACKET AND FASTENERS
MLO-1421-87

Rack Mount Instructions

B—Db

Slide the system into the rack.

MLO-1422-87

Attach the nylon stop cable.
LEFT REAR RACK

NYLON STOP CABLE

SLIDE UNIT iN PLACE AND
SECURE NYLON CABLE AS SHOWN

MLO-1423-87

B—6

MicroVAX Il 830QY, 63007 Installation

10. Prepare the cover.

B TAP sCREW(S)
1

MLO-1424-87

11. Attach the cover.

PRESS FIRMLY IN PLACE

MLO-1425-87

12. Continue with the instructions in Section 4.

Rack Mount Instructions

B—7

MicroVAX11630QY,630QZ2
Operation
Order Number EK-O03AB-OM-002

digital equipment corporation
maynard, massachusetts

December 1986

September 1987
The information in this document is subject to change without notice and should not be construed as a
commitment by Digital Equipment Corporation.
Digital Equipment Corporation assumes no responsibility for any errors that may appear in

this document.

The software, if any, described in this document is furnished under a license and may be used or copied
only
in accordance with the terms of such license. No responsibility is assumed for the use or reliability of
software
or equipment that is not supplied by Digital Equipment Corporation or its affiliated companies.
Copyright ©1986, 1987 by Digital Equipment Corporation.

The READER’S COMMENTS form on the last page of this document requests the user’s critical evaluation to
assist in preparing future documentation.
The following are trademarks of Digital Equipment Corporation:

COMPACTape

MASSBUS

DEC

MicroVAX

ULTRIX

DECmate

PDP

UNIBUS

ThinWire

DECnet

P/0OS

VAX

DECUS

Professional

VAXcluster

DECwriter

Q-bus

VAXELN

DELNI

Rainbow

VMS

DEQNA

RSTS

DESTA

RSX

Work Processor

DIBOL

digii tiallly
ML-5810

FCC NOTICE:
energy.

The equipment described in this manual generates, uses, and may emit radio frequency
The equipment has been type tested and found to comply with the limits for a Class A computing

device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection
against such radio frequency interference when operated in a commercial environment. Operation
of this
equipment in a residential area may cause interference, in which case the user at his
own expense may be
required to take measures to correct the interference.

Contents
Preface

vii

Chapter 1
1.1

System Overview

Front Panel of the Pedestal Mount . . . ... ............

1-2

1.1.1

Control Panel . . . .. ....... ... ... ... .........

1-3

1.1.2

Mass Storage Devices

1-5

1.2

1.2.1
1.2.2

. . ... ... ... ... ...,
.. ....

Rear View of the Pedestal Mount.

. . ... .............

1-5

Controls on the CPU Panel . . . .. ................

1-5

Insert Panels for Connecting Devices.

. . ... .........

1-7

Functional Description of Base System Components . . . . . . .

1-7

Base System Components . . . . ..................

1-8

Central Processing Unit (CPU) ... ..............

1-8

1.3.1.2

Console Serial Line Unit (SLU).

1-8

1.3.1.3

Main Memory . . . . ...... . ...

1.3.1.4

Mass Storage Devices and Controllers

. ...........

1-9

1.3.1.5

Power Supply . . . ........
... .. .. ...

1-10

Fans . . .. ... .. .

1-10

1.3
1.3.1
1.3.1.1

1.3.1.6
1.3.2

Optional Components

. ... ............
.. ... . . . . ...

. .. .....................

1-8

1-11

1.3.2.1

Communications Controllers

. ... ..............

1-11

1.3.2.2

Real-Time Controllers . . . ... .................

1-12

1.3.2.3

Printer Interfaces . . . . . ... ...

... . .. .. ...,

1-13

1.3.24

Other Available Options . . . .. ................

1-13

Chapter 2

Using the System

2.1

Before You Use a New System . ...................

2-1

2.2

Switch Settings

221
222

. . ........
... . . ..

2-1

Normal Operation . . . . .........
.. ............

2-2

Special Operation . .. ........................

2-2

TurmningOntheSystem .. .......................

2-3

Bootingthe System . ...............
... . ... ...

2-4

24.1

Autobooting the System . . . .. ...............
...

2-4

242

Booting the System from Console Mode

. ... ........

2-5

UsingtheSystem ...............
... ....... ...,

2-6

Turning Off the System . . . .. .......
... .........

2-7

2.7

HaltingtheSystem . .. .................
... ...,

2-7

2.8

Restarting the System . ... ........... e

2-7

Chapter 3
3.1

Using System Options

Mass Storage Options . . . .........
... .. ..........

3-1

3.1.1

RD50-Series Fixed-Disk Drives . . . . . ..............

3-1

3.1.2

Diskette Drives . . . . . ...

... .. . . ...

3-3

3.1.21

RX50 Diskette Drive . . . . . ... ................

3-6

3122

RX33 Diskette Drive . . . . .. ..................

3-9

3.1.3
3.1.3.1
3.1.3.2

3.2
3.2.1
3.2.1.1

3.2.1.2
3.2.2

3.2.3

TK-Series Tape Drives

...

. . . . .. .......
... .. .......

TK70 Tape Drive . . . ... ...

3-11

. ...

. ... ...,

3-16

TKS50 Tape Drive . . . . .. ... ... ...

o o

3-23

Communications Options . . . .. ...................

3-33

Asynchronous Serial Controllers . . . . ..............

3-33

Without Modem Support.

With Modem Support.

. .. .................

3-33

. . .........
... ... ......

3-34

Synchronous Controllers . . . . .. .................

3-35

Network Controllers

. .. ......................

3-35

Real-Time Controllers . . ........................

3-35

Printer Options

3-36

3.5

Adding New Options

3.3

. . .........
... ... .. .............

. . ................
... .....

3-36

Appendix A

Related Documentation

Glossary

Index
Figures

1-1
1-2

MicroVAX II 630QY Pedestal Mount. . .. .............
Control Panel ... ... .. ... ... .. ...

1-5

Controls onthe CPUPanel ......................
Insert Panels on the MicroVAX 11 630QY . .. ... ... ... ..
. ......
... ... ...
System Air Circulation . .......

2-1

Language Selection Menu.

1-3
i-4

2-2

2-3
3-1
3-2

3-3
3-4
3-5

3-6
3-7

3-8
3-9
3-10
3-11
3-12
3-13

1-2
1-3
1-6
1-7
i-10

. .. ....................
...
Successful Power-On and Automatic Boot . .. .......
..........
...
.
.
Mode
Successful Power-On to Console

2-3
2-5

. .. ....... ... ...
Proper HandlingofaDiskette . . .. ... ..............

3-2

Fixed-Disk Controls

Write-Protecting a Diskette . . . . ...................
oL
RX50 Diskette Drive . . . ... ... ... ... .
Inserting an RX50 Diskette . . .. ...................

.. .........
.. .....
RX33 Diskette Drive . . . ......
Inserting a Diskette into the RX33 Diskette Drive ... ... ..

Labeling a Tape Cartridge . .. ... .................
Tape Cartridge Write-Protect Switch . . . ..............
TK70 Tape Drive . .. ... .. ... ...
Inserting a Tape Cartridge into a TK70 Tape Drive .. ... ..
Removing a Tape Cartridge from a TK70 Tape Drive . . . . ..

TK50 Tape Drive . . ... ... ... ...
3-14 Tapeleaders. ... ...... ... ...
3-15 Checking the Cartridge Leader . ... ................
3-16 Checking the Drive Leader . . .. . ..................
3-17 Inserting a Tape Cartridge into a TK50 Tape Drive . ... ...

3-18 Removing a Tape Cartridge from a TK50 Tape Drive . . . . ..

2-6
3-4

3-6
3-7
3-9

3-10
3-11
3-13

3-14
3-17
3-19
3-21
3-24
3-25
3-26
3-27
3-29
3-31

Tables
Controls and Indicator Lights

. .. ..................

1-4

Normal Power-On Indications . . ... ................

2-4

TK70 Tape Drive Controls

. ......................

TK70 Tape Drive Indicator Lights
TK50 Tape Drive Controls

3-22

. .. ....................

3-32

TK50 Tape Drive Indicator Lights

3-22

. .................
. . ................

3-32

Preface
This manual describes how to operate your MicroVAX 1I 630QY, 630QZ

system.

It assumes the system has been properly installed, as described in

MicroVAX II 630QY, 630QZ Installation.
This manual is structured as follows:

Chapter 1 provides an overview of the system.

Chapter 2 describes how to use the system.

Chapter 3 describes how to use options installed in the system.

An appendix lists related documentation.

A glossary defines key terms.

vii

Chapter

System Overview
A VTAVTT
nNYv
x
The MicroVAX
II 630QY,
630QZ system
contains all components in one metal

T -~ AAL A

chassis called a BA23 enclosure. Systems installed in a pedestal mount are
called 630QY systems. Systems installedin a rack are called 630QZ systems.
The illustrations in this manual show a pedestal-mounted system.

Rack-mounted systems differ from pedestal-mounted systems in two ways.
The rear panel is not attached, easing access to some controls, and the unit is
mounted horizontally. In descriptions of the system, references to up become
right and references to down become left. The different orientation primarily
affects operation of the TK50 and TK70 tape drives.

Descriptions and illustrations in this manual assume the system has mass
storage devices. If your system is a satellite node on a VAXcluster (a group
of computers networked together under the control of a server node), it may
be diskless. Diskless systems boot all software over the network from the
server node and store all data on mass storage devices on the server node.
Instructions specific to diskless systems occur periodically throughout this
manual. Consult your VAXcluster software documentation for more details
on using your satellite node.

This chapter introduces you to the system components and their functions.

The chapter describes the front and back of the system and the functions of
system components. Chapters 2 and 3 describe how to use the system and
installed options.

System Overview

1-—1

1.1

Front Panel of the Pedestal Mount

The front of the system has a control panel and mass storage devices, unless
the system is diskless.

All illustrations in this manual show systems with

mass storage devices. Systems with mass storage have a fixed-disk drive and

one of the following: an RX50 diskette drive, an RX33 diskette drive, a TK50
tape drive, or a TK70 tape drive.
Figure 1-1 shows the front of the pedestal mount equipped with a TK50 tape

drive.

Figure 1-1:

MicroVAX Il 630QY Pedestal Mount

CONTROL

PANEL

T—— TK50
TAPE

DRIVE

MLO-1426-87

1-2

MicroVAX Il 630QY, 63002

Operation

1.1.1 Control Panel
The control panel has several controls and indicators, as seen in Figure 1-2,

Figure 1-2:

Control Panel

oneoen|

Run

ON/OFF

DC OK

O
Hatt

O
Restart

Fixed Diek 0
Write Protect

Ready

MLO-~1427-87

Table 1-1 lists the functions of the various controls and indicators.

System Overview

1-3

Table 1-1:

Controls and Indicator Lights

Control

Position

Function

Turns on the system.

Turns off the system.

Out (not lit)

Normal operating setting.

In (glows red)

Halt enabled.

Momentary contact

Returns the system to a power-on condi-

On/Off

(1/0)

switch

Halt button!

Restart button

tion. Self-tests are run and the system re-

pushbutton

boots. Work in progress is lost.
Write-Protect

Write

Out (not lit)

for

button

enabled,

software

ware

can

the

normal

operation.
read

position

System
write

soft-

informa-

tion on the fixed disk.
In (glows orange)

Write-protected.

System software can-

not write on the fixed disk.
Ready button

Out (glows green)

Disk is available for use, the normal po-

sition

for

software

operation.

Sys-

tem software can read information on

the fixed disk.

If the Write-Protect but-

ton is in the out position, system software can also write on the fixed disk. The

green light in the Ready button also in-

dicates disk

activity.

When the but-

ton is out but not lit, activity is occur-

ring. The disk is not available for use until

completes

the

current

opera-

tion.

Disk is not available for use. System soft-

In (not lit)

ware can neither read from nor write to

the fixed disk.

1When the Halt Enable/Disable switch on the rear of the system is set to disable, the Halt button has no ef-

fect on system operation. The Halt button glows red when depressed, regardless of whether the system is actually halted.

1-4

MicroVAX 1l 630QY, 6300Z

Operation

Table 1-1 (Cont.):

Controls and Indicator Lights

Indicator

Run

Function

Glows green when the CPU is operating.

DC OK

Glows

green

ply

generating

when

the
the

power

sup-

correct

volt-

ages.

1.1.2 Mass Storage Devices
Your system has two types of mass storage: removable and fixed. The
removable type may be an RX50 diskette drive, an RX33 diskette drive, a
TK50 tape drive, or a TK70 tape drive. Either is installed just below the
control panel. Most illustrations in this manual show a system with an RX50
diskette drive installed. The system’s fixed-disk drive is behind the panel,
below the diskette drive or tape drive.

Controls for the fixed-disk drive are on the control panel described earlier in
this chapter. Controls and indicators for the diskette drives and tape drives
are described in the sections on those devices in Chapter 3.

1.2 Rear View of the Pedestal Mount
When you remove the rear panel of the system, you have access to controls
on the CPU panel and connectors for peripheral devices.

1.2.1 Controls on the CPU Panel
Figure 1-3 shows the controls on the CPU panel.
The CPU panel has the following components:

Halt Enable/Disable switch—When the switch is set to the left (dot
outside circle), halt is disabled. When the switch is set to the right (dot
inside the circle), halt is enabled. When halt is enabled, pressing the
key on the console terminal
Halt button on the control panel or the
stops the processor and transfers control to the console program.

System Overview

1-5

Figure 1-3:

Controls on the CPU Panel

BAUD
RATE

SWITCH

POWER-UP

MODE

SWITCH

HALT

ENABLE/DISABLE

SWITCH

CONSOLE

LED

TERMINAL
CONNECTOR

DISPLAY

MLO-1428-87

Power-Up Mode switch—This 3-position rotary switch determines how

the system responds at power-up:

Run Mode (indicated by an arrow) is the normal operation setting.

Language Inquiry Mode (indicated by a human profile) causes the
system to display a language selection menu at power-up (assuming
your console terminal supports character sets for multiple languages).

Loop Back Test Mode (indicated by a T in a circle) causes the system
to run loopback tests at power-up. This setting is for DIGITAL service
use only.
*

Baud rate switch

Console terminal connector—This provides the connection for the console

terminal.

LED display—This shows the testing sequence during power-up.

1—6

MicroVAX Il 630QY, 63007

Operation

1.2.2 Insert Panels for Connecting Devices
Your system has two kinds of insert panels for connecting additional devices.

Figure 1-4 shows the two types of insert panels.
Figure 1—4:

Insert Panels on the MicroVAX Il 630QY

ADDITIONAL
DEVICES

CABLE

Internal cabling runs from the connectors on the insert panels to the modules
installed in the card cage.

1.3 Functionai Description of Base System

Components
Each MicroVAX II 630QY, 630QZ system includes base system components

common to all systems, and perhaps optional components. Your system was

preconfigured at the factory, based on your order.
The following sections describe base system components and options in turn.

System Overview

1-7

1.3.1

Base System Components

Base system components include the following:

Central processing unit (CPU)

Console serial line unit (SLU)

°*

Main memory

Mass storage devices and controllers (except for diskless systems)

Power supply

Fans

1.3.1.1 Central Processing Unit (CPU)
The central processing unit (CPU) controls the execution of all instructions and
processes.

Its circuits contain all the logic, arithmetic, and control functions

used by the system, as well as 1 Mbyte of main memory.

1.3.1.2 Console Serial Line Unit (SLU)
Each system has a serial line unit (a line on which each bit of information is
sent sequentially on a single channel) connecting the console terminal to the

CPU module. The SLU connector is located on the CPU panel. The console
serial line provides a means of communicating with the CPU.

1.3.1.3 Main Memory
Main memory provides the physical storage area for all data and instructions
used by the CPU. When you start your system, the operating system is
loaded into main memory. Any application programs must also be loaded
into memory.

When the system cannot load everything into memory at once, it reads in
units of data called pages (512 bytes of data) from disk. A large main memory
increases the efficiency of processing, as fewer pages must be copied to and

from the disk. Each configuration comes with a standard memory option that,
you can upgrade to increase efficiency.

The contents of memory are volatile. This means they are lost when you
turn off power to the system. You use mass storage devices, such as fixed

disks and tape cartridges, to store software and data permanently.

1-8

MicroVAX I 630QY, 6300Z

Operation

1.3.1.4 Mass Storage Devices and Controllers

Mass storage devices record data on magnetic media. The data recorded is
not lost when you turn off the system, but can be altered or erased if you
record over it. You use mass storage devices to store data and software

permanently. When the data or software is needed, the CPU copies it from
the mass storage device into main memory.

A diskless system does not have its own mass storage devices, but uses the
mass storage devices on the server.

The two primary types of mass storage devices are fixed-disk drives and
devices with removable media, such as diskettes and tape cartridges.
Fixed-Disk Drives

One fixed-disk drive is permanently installed in your system, A fixed-disk
drive provides large-capacity storage for software and data files, as well as

rapid access to the data by the CPU.

Chapter 3 describes how to use the fixed-disk drive on your system.
Devices with Removable Media

The MicroVAX II 630QY, 630QZ system can have one diskette drive (either
an RX33 or an RX50) and cone tape drive (either a TK50 or a TK70). You
can use any of these devices as an input or output device. You use a device
as an input device when you install software or copy data from a diskette or
tape cartridge to your system. You use a device as an output device when
you copy software or data from your system to a diskette or tape cartridge.
You can copy individual files or programs, or you can copy (back up) the
contents of an entire fixed disk. Your system software manuals explain how
Mass Storage Controllers

All mass storage devices require a controller, a separate module that controls
all activity between the CPU and the mass storage devices. The controller for
the fixed-disk drives and the diskette drives (the RQDX3) and the controller
for the TK50 or TK70 tape drive (the TQK50 or TQK70, respectively) are
installed in the card cage.

System Overview

1-9

1.3.1.5 Power Supply
The system has a power supply that powers all system components. When
the power supply is generating the proper voltage, the DC OK light on the
front control panel glows green.

1.3.1.6 Fans
Two fans inside the BA23 enclosure draw in air from the bottom of the

system and pull it up through the modules and out the top, as shown in
Figure 1-5. To reduce the load on the fans, keep the system away from

heat sources and provide space for ventilation.
covering the vents.

Figure 1-5:

Do not block circulation by

System Air Circulation

MLO-1430-87

1—10

MicroVAX Il 630QY, 63007

Operation

1.3.2 Optional Components
System options can include multiples of components that are part of the base

system (for example, additional memory modules) and the following kinds
of options:
e

Communications controllers

Real-time controllers

Printer interfaces

1.3.2.1 Communications Controllers
Every system has a serial line (a line on which each bit of information is sent

sequentially on a single channel) connecting the console terminal to the central
processing unit (CPU) module. Most systems have additional communications
controilers for connecting additional terminais and for communicating with
other systems over telephone or network lines. Communications controllers
provide standard interfaces between peripheral devices and the system. Many

communications controllers provide support for multiple data lines.
The following types of communications controllers are available:
*

Asynchronous serial controllers

®*

Synchronous serial controllers

Network controllers

Serial controllers transmit data one character at a time.

A device at the

transmitting end breaks bytes of data into bits. A device at the receiving end
assembles incoming bits into bytes of data.

Asynchronous Serial Controllers
Asynchronous

serial

controllers

provide

peripheral devices and the system.

low-speed

connections between

Asynchronous communication between

the system and the peripheral depends on recognition of a pattern of start
and stop bits, not on a time interval.

Asynchronous serial controllers may be divided into those without modem
support and those with modem support.

You use asynchronous serial controllers without modem support to connect
additional terminals and printers to your system.

NOTE: Printers equipped with a microprocessor (intelligent printers) may require
modem control signals to function correctly.

Do not attach a printer requiring

System Overview

1-11

modem control signals to a controller with no modem support. Check your printer
documentation to determine the proper communications interface for your printer.
Communications controllers with modem support allow you to communicate
over telephone lines. With a modem connected to your system, you can
access other computers and you can dial into your system from a remote
terminal or computer.

Computers transmit digital signals, while telephone lines (with the exception
of digital leased lines)

transmit analog signals.

@When two computers

communicate over telephone lines, a modem is required at both the
transmitting and receiving ends of the line. At the transmitting end, the
modem converts digital signals from the computer (or terminal) to analog
signals prior to transmission over telephone lines. At the receiving end,
another modem converts the analog signals from the telephone line back into
digital signals the computer can understand.

While all modems have the same basic function, some have more advanced
features, such as auto-answer.

These advanced features require additional

modem control signals. The difference between limited and full modem
support depends on the number of modem control signals recognized by
the communications device.

Full modem support (according to DIGITAL

standards) requires recognition of eleven signals.

Synchronous Serial Controllers
Synchronous serial controllers provide a high-speed connection between

systems.
Communication between synchronous devices depends on
time intervals that are synchronized before transmission of data begins.
Synchronous devices can also have modem support.

Network Controllers
Network communications controllers allow you to connect to an Ethernet
network. With a network connection and appropriate DECnet software, you

can use network services, such as mail; access data stored on other systems;
perform operations, such as editing and printing on remote systems; and

share resources, such as laser printers.

1.3.2.2 Real-Time Controllers
Real-time controllers interface devices that monitor processes, for example,
laboratory equipment or manufacturing equipment connected to the system.

Typically, real-time controllers are parallel devices, not serial devices. Parallel

devices transmit more than one bit of information simultaneously.

1-12

MicroVAX il 630QY, 6300Z

Operation

1.3.2.3 Printer Interfaces

Some printers require specific interfaces to communicate with the system.
For example, the LP25/26/27 printers and the LG01/02 printers require the
LPV11 interface.

1.3.2.4 Other Available Options

Your system arrives preconfigured with the options you ordered. As your
needs change, you can add more options. Your DIGITAL salesperson can
advise you on available options.
MicroVAX II 630QY, 630QZ Technical
Information describes the options currently available for MicroVAX II 630QY,
630QZ systems. DIGITAL Field Service provides option installation.

System Overview

1-13

Chapter 2

Using the System
The first section of this chapter describes procedures appropriate only to new
systems.

The remainder of the chapter describes how to use your system

once the system software has been correctly installed.

2.1

Before You Use a New System

This chapter

assumes

that your system has been properly installed

described in MicroVAX II 630QY, 630QZ Installation.
System software and diagnostic software can be on either RX50 diskettes or
TK50-format tape cartridges. If your system has an RX33 diskette drive, you

can use the RX50 diskettes. Before running diagnostic software or installing
system software, you should read Section 3.1.2.1 (RX50), 3.1.2.2 (RX33),

3.1.3.1 (TK70), or 3.1.3.2 (TK50) on how to operate the appropriate drive.
If

a DIGITAL service representative installed your system, he or she ran

the diagnostic software shipped with your system. If you installed your own

system, you may want to run the diagnostic software before you install system
software. See MicroVAX II 630QY, 630QZ Troubleshooting for instructions.
After running the diagnostic software, install system software.

Follow the

instructions provided in the system software installation manual.

Some of

the instructions may require you to remove the rear panel to change switch
settings on the CPU panel.

The remainder of this chapter assumes that system software has been installed.

2.2 Switch Settings
Switch settings vary, depending on the operation being performed. The next
two sections describe switch settings for normal and for special operations.

Using the System

2-1

2.2.1

Normal Operation

Switch settings for normal operation are the following:
The Halt Enable/Disable switch on the CPU panel is set to disable (left).
Once system software is installed, DIGITAL recommends you run your
system with halt disabled to prevent the user of the console terminal from
inadvertently halting the system by pressing

the front control panel.

or the Halt button on

Halting the system causes all activity to stop.

With halt disabled, your system automatically boots system software
when powered up.
The Power-Up Mode switch on the CPU panel is set to Run (indicated

by an arrow).
The baud rate switch on the CPU panel is set to 9600.
The Write-Protect button for the fixed-disk drive is set to out (not lit).
This setting allows system software to write to the disk.

The Ready button for the fixed-disk drive is set to out (glows green when
the disk is not being used).

This setting makes the drive available for

use.

The Halt button is set to out (not lit).

2.2.2 Special Operation
Certain operations require that you change some of the normal operating
settings.

When you install system software and perform certain types of backups,
your system software manuals may tell you to set the Halt Enable/Disable

switch to enable (right).

If your system has been powered off for more than 10 days, the battery
unit that saves the system clock and the language selection may have
run down.

Set the Power-Up Mode switch to Language Inquiry Mode,

indicated by a human profile, before you turn on your system.

When

you turn on your system, a Language Selection Menu appears, as shown

in Figure 2-1.

2—2

MicroVAX Il 6300QY, 63007

Operation

Figure 2—1:

Language Selection Menu

”"’

KAB30- AVv1.2
Dansk

2) Deutsch

Norsk

3) English

Portugués

4) Espaifiol

10)

Suomi

5) Frangais

11)

Svenska

Nederlands

Italiano

(1..11):

MLO-1672-87

Select a language by typing in the number listed next to the language.
Save the language you have selected by rotating the Power-Up Mode
switch to Run Mode, indicated by an arrow. Once the system is booted,
reset the system clock, as described in your system software manual.

2.3 Turning On the System
Once you have set the switches appropriately, you are ready to turn on the
system. Use the following procedure:

Turn on the console terminal and wait for it to complete its self-tests.

Turn on the system by setting the on/off switch to 1.

When you turn on the power, you should see the indicators listed in Table
2-1.

Using the System

2—3

Table 2-1:

Normal Power-On Indications

Indicator

Normal Indication

DC OK

Glows green

Fixed-disk Ready light

Glows

green

within

sec-

onds
TK50 tape drive Load/Unload button

Glows red for 2 seconds and

then goes out
TK50 tape drive indicator light

Glows green

when

red

light

goes out

TK70 tape drive indicator lights

Orange,
lights

yellow,

glow

and

during

green

self-tests.

The green light remains on.

If you do not observe the indications in Table 2-1, refer to MicroVAX II
630QY, 630QZ Troubleshooting.
Every time you turn on your system, it runs a series of self-tests. Your
console terminal displays a countdown from 7 to 3 as the system tests itself.

When the tests are successful, you receive the message “Tests completed.”
When your system detects an error during its self-tests, the countdown may
never start, may stop before reaching 3, or an error message may appear. See

MicroVAX II 630QY, 630QZ Troubleshooting for help in locating the problem.

2.4 Booting the System
You have the option of autobooting the system or booting from console mode.

The setting of the Halt Enable/Disable switch determines how the system

boots.

2.4.1 Autobooting the System
When the Halt Enable/Disable switch is set to disable (the normal operating
setting),

the system attempts to load system software after successfully

completing its self-tests.

If the system finds bootable system software, you

receive the messge “Loading system software”, and a countdown from 2 to 0

displays on the screen, as shown in Figure 2-2.

2-4

MicroVAX Il 630QY, 6300Z

Operation

Figure 2—2:

Successful Power-On and Automatic Boot

)
Performing normal

system

tests.

7..6..5..4..3..
Tests

completed.

Loading system

software.

2..1..0..

v,
MLO-1431-87

2.4.2 Booting the System from Console Mode
When the Halt Enable/Disable switch is set to enable, the system powers up
to console mode (indicated by the >>> prompt) after successfully completing

its self-tests. Figure 2-3 shows a successful power-on to console mode.

Using the System

2-5

Figure 2-3:

Successful Power-On to Console Mode

[

Performing normal

system

tests.

7..6..6..4..3..

Tests

completed.

>>>

MLO-1432-87

To load system software from console mode,

you must use the BOOT

command (BOOT device-name). For example, BOOT MUAUO telis the system

to boot software from a cartridge in the TK50 or TK70 tape drive. Software
manuals may instruct you to power up with halt enabled and to use the
BOOT command.

2.5 Using the System
Once the system software is loaded, the first display for the system software
appears on the console terminal after a few seconds. That display is described
in the system software documentation.

You are now ready to use the system. Refer to the system software manuals
and application manuals for more specific instructions on using the system.
Your system software manuals cover the following:

Installing software on your system

Running software to perform tasks

2—6

MicroVAX 1l 630QY, 63007

Operation

Making and restoring backup copies of system software or data files

Accessing devices and utilities in your system

2.6 Turning Off the System
—r

o~
£~
Do not turn off your system uniess i requires maintenance or you know of
a planned power outage.

CAUTION: Turning off your system without following the shutdown procedure
described in your system software manuals may result in loss of data.
Once you have completed the recommended procedure, you can turn off

your system by setting the on/off switch to 0.

NOTE: Users of diskless systems in a VAXcluster should not turn off, hait, or
restart their sysiems without consulting the cluster manager. These activities
affect the functioning of the entire cluster.

2.7 Halting the System
Halting the system interrupts all processes and returns control to the console
program. You may need to halt the system during software installation. Or,
you may want to boot the system from another device, for example, a tape
cartridge containing MicroVAX diagnostic software.
To halt the system, first set the Halt Enable/Disable switch on the CPU panel
to enable (indicated by the dot inside the circle). To halt the system, press
in the Halt button on the control panel (glows red) or press the
key on

the console terminal. When the console mode prompt >>> appears on your
screen, the system is halted.

2.8 Restarting the System
Restarting the system aborts all current and pending operations and returns
the system to a power-on condition. The usual power-on tests are run. To
prevent loss of data, warn all users to log off prior to restarting the system.

You restart the system by pressing in the Restart button on the control panel.

Using the System

2—7

Chapter 3

Using System Options
This chapter describes how to use options that may already be part of your
system, or that you can add to your system. The following types of options

are covered:

Mass storage devices and controllers

Communications controllers

Real-time controllers

Printers

3.1 Mass Storage Options
The following mass storage options are available for the MicroVAX II 630QY,
630QZ system:
*

RD50-series fixed-disk drives

RX50 diskette drive

RX33 diskette drive

TK50 tape drive

TK70 tape drive

3.1.1 RD50-Series Fixed-Disk Drives
RD50-series fixed-disk drives provide high-volume mass storage for your
MicroVAX II 630QY, 630QZ system. Your system has one RD50 series drive,
Fixed Disk 0. Two buttons on the control panel, the Ready button and the
Write-Protect button, control the operation of the fixed disk.

Figure 3-1

shows the controls.

Using System Options

3-1

Figure 3—1:

Fixed-Disk Controls

dilalilt| I

Run

DC OK

O
Halt

O
Restart

Fixed Disk O

Write Protect

Ready

oTM

FIXED-DISK 0

READY BUTTON

MLO-1433-87

The Ready button controls whether the fixed disk is available for use.

use the fixed disk, you must set the Ready button to out (glows green when
the disk is available for use), the normal operating setting. When the Ready
button is out, the system can read from the fixed disk.

When the Write-

Protect button is also out, the system can write to the disk. The green light in

the Ready button indicates whether activity is occurring on the disk. When
the light is on, no activity is occurring and the disk is available for use. When
the light is off, activity is occurring.

If you want to automatically boot from another device, such as an RX50
diskette or a tape cartridge, you must set the Ready button to in (not lit).
When the Ready button is in, the system can neither read data from the
disk nor write data to the disk. (You can also use the BOOT command from
console mode to specify another boot device.)
The Write-Protect button controls whether the system can write data to the

fixed disk.

To write data to the disk, write-enable the disk by setting the

Write-Protect button to out (not lit). Your system disk must be write-enabled
for the system to function. Because the MicroVAX IT 630QY, 630QZ has only
one fixed-disk drive, you should never write-protect the disk.
The storage capacities and other specifications of the various disk drives in
the RD50 series are listed in MicroVAX II 630QY, 630QZ Technical Information.

3—2

MicroVAX Il 6300Y, 63007

Operation

3.1.2 Diskette Drives
The MicroVAX II 630QY, 630QZ can have either an RX50 diskette drive or

an RX33 diskette drive.

You can use RX50 diskettes in an RX33 diskette

drive, but the diskette capacity is reduced. You cannot use RX33 diskettes in

an RX50 diskette drive.

CAUTION: Inserting an RX33 diskette into an RX50 diskette drive can destroy
data on the diskette.

You can differentiate between the two types of diskettes by the color of
the plastic jacket:

the RX33 diskette is enclosed in a gray jacket; the RX50

diskette is enclosed in a black jacket.
You can use either diskette as both an input and output device.

Use the

diskette as an input device to load software or data into your system.

Use

the diskette as an output device to make copies (or backups) of software or
data.

Handling and

storage

guidelines

and write-protecting

the

two types

diskettes are identical.

Diskette Handling and Storage Guidelines
Figure 3-2 shows the proper way to handle a diskette.

Using System Options

3—3

Figure 3—2:

Proper Handling of a Diskette

DISKETTE

WRITE-PROTECT

- \OTCH

DISKETTE
COVER

DISKETTE
SURFACE—
DO NOT
TOUCH

ORANGE
ARROW

PROTECTIVE
ENVELOPE

~——

|+
;

MLO-1434-87

3—4

MicroVAX Il 630QY, 630QZ

Operation

Use the following guidelines when handling or storing diskettes:
Do not touch the exposed surfaces of the diskettes.
Always return a diskette to its protective envelope to keep out dust and
dirt.

Do not bend or fold a diskette.
Always store diskettes vertically and loosely to prevent the covers from
.

ANV
T YN
Y

TAT

Write on the diskette label before applying it to the diskette. Writing on
the diskette itself might damage the diskette.
Keep diskettes away from direct sunlight, heaters, and other sources of
heat.

Keep diskettes away from magnets and equipment that generates magnetic
fields, such as motors, transformers, and terminals.
Make and keep backup copies of all working diskettes.

Refer to your

system software manuals for instructions.

Using System Options

3—5

Write-Protecting a Diskette
Write-protecting a diskette prevents accidental erasure of information stored
on the diskette.

To write-protect a diskette, cover the write-protect notch

with one of the self-adhesive foil tabs supplied with your diskettes. You can

later add or change information on the diskette by removing the write-protect
tab. The tab is shown in Figure 3-3.

Figure 3—3:

Write-Protecting a Diskette

MLO-1435-87

3.1.2.1

RX50 Diskette Drive

The RX50 dual diskette drive holds two 5.25-inch single-sided diskettes. The
drives are labeled 1 and 2. (See Figure 3-4.) Each drive has a red indicator
light that glows when the drive is in use.

3—6

MicroVAX Il 630QY, 6300Z

Operation

Figure 3—4:

RX50 Diskette Drive

ACTIVE DRIVE
LIGHTS

MLO-1436-87

FEach diskette stores 400 Kbytes of information, which is roughly 150
typewritten pages. Information is stored magnetically in a specified format.
a4

CAUTION: Use only preformatted RX50 diskettes, available from DIGITAL or
its licensed distributors.

Because each drive can read and write data on only one side of a diskette,
you must insert the diskette properly. Inside each drive door is an orange
stripe that you align with an orange arrow on the diskette.
When you insert a diskette into the drive, it rotates inside its protective cover.

When the system is reading data from the diskette or writing data to it, the
red indicator light for that drive is lit.

CAUTION: Do not open a drive door when the indicator light for that drive is
on. Information stored on the diskette could be lost.

Using System Options

3—7

Inserting and Removing an RX50 Diskette
Use the following procedure to insert an RX50 diskette. (See Figure 3-5.)

Open the diskette door by pressing on its outer edge.

Align the orange arrow on the diskette with the orange stripe on the
drive and insert the diskette.

Press the drive door to close it.

3—8

MicroVAX Il 630QY, 630QZ

Operation

Figure 3—-5:

inserting an RX50 Diskette

MLO-1437-87

When you are ready to remove the diskette, make sure the red indicator light
on the drive is off before you open the drive door. Close the door after you
have removed the diskette.

3.1.2.2 RX33 Diskette Drive

The RX33 diskette drive holds one double-sided, high-density RX33 diskette
or one single-sided, lower density RX50 diskette. Each RX33 diskette holds
1.2 Mbytes of data (.6 Mbyte on each side). Each RX50 diskette holds .4
Mbyte of data.

RX33 diskettes must be formatted before you can use them. Formatting
prepares the diskette to accept data. You format RX33 diskettes by using
the Formatter Utility available in the MicroVAX Diagnostic Monitor (MDM).
MDM and the Formatter Utility are described in Chapter 3 of MicroVAX Il

Using System Options

3—9

630QY, 630QZ Troubleshooting. Be sure to keep a supply of formatted diskettes

on hand. RX50 diskettes come preformatted.
When you insert a diskette into the drive, the diskette rotates inside its
protective cover. When the drive is active, the red indicator light on the front

of the drive is lit.

Figure 3-6 shows the front of the drive, including the

indicator light and the lever that controls access to the drive.

CAUTION: Do not attempt to remove a diskette when the red light is lit.
Information stored on the diskette could be destroyed.

Figure 3—6:

RX33 Diskette Drive

DISKETTE

DIRECTION

|} ArRROW

T FRONT PANEL LEVER

(LOCKED POSITION}

RED

INDICATOR —
LIGHT

MLO-1458-87

Inserting and Removing Diskettes
Use the following procedure to insert both RX50 and RX33 diskettes.

(See

Figure 3-7.) Make sure the red indicator light on the drive is not lit before
you insert a diskette.
1.
2.

Move the lever to the unlocked position.
Hold the diskette so that the write-protect notch is down and the diskette
label is up. Insert the diskette into the slot until it snaps into place.

3—10

MicroVAX Il 630QY, 6300Z

Operation

Move the lever to the locked position.

NOTE: Do not force the lever. Make sure that the diskette is fully inserted.
The lever must be in the locked position for the drive to function.

Inserting a Diskette into the RX33 Diskette Drive

\\=

Figure 3—7:

IEEi

V‘J//:

MLO-1439-87

3.1.3 TK-Series Tape Drives
The MicroVAX II 630QY, 630QZ can have either a TK50 or TK70 tape
drive. You can record data on blank COMPACTape or COMPACTape II
tape cartridges using either drive. However, DIGITAL recommends that you
use only COMPACTape 1I tape cartridges when recording with a TK70 tape
drive. You can identify the type of cartridge by the label. The COMPACTape

Using System Options

3—11

IT has a blue label strip. On the TK50 tape drive, the capacity is 95 Mbytes;
on the TK70 tape drive, the capacity is 296 Mbytes.

Once data has been recorded in a particular format (either TK50 format or
TK70 format), you can record over the data using the same type of drive.
For example, if you recorded data in TK50 format, you can record new data

on the tape if you use a TK50 drive.
tape using a TK70 drive.

You cannot record new data on the

The TK70 drive recognizes the TK50 format, and

write-protects the tape.

Similarly, you cannot use a TK50 to record over a
tape first recorded on a TK70 drive.

The TK70 drive can read tapes recorded on a TK50 drive.
Software is
distributed in the TK50 format and can be read by both TK50 and TK70
drive. The TK50 drive cannot read data recorded by a TK70.

Labeling the cartridges, write-protecting the cartridges, and handling and
storage guidelines are identical for COMPACTape and COMPACTape II tape

cartridges, regardless of the recording format.
The following subsections
discuss each of these procedures in turn.
The design and operation of
the two tape drives differ.
If your system has a TK70 tape drive, read

Section 3.1.3.1. If your system has a TK50 tape drive, read Section 3.1.3.2.

Labeling a Tape Cartridge
When recording data on a cartridge, label its contents. For your convenience,
a slot for the label is provided on the front of the cartridge.
Write the
identification on the label first, then insert the label in the slot on the front

of the cartridge, as shown in Figure 3-8. The label remains visible when the

tape is in the drive.

3-12

MicroVAX Il 630QY, 63007

Operation

Labeling a Tape Cartridge

dlifgliltall I

¢
V7,- Compeciane//’

Figure 3—-8:

206mB[] R

AAAN_OF

MLC-1440-87
AAU

If the tape was recorded on a TK70 tape drive, put a check in the box labeled
296MB. If the tape was recorded on a TK50 drive, check the box labeled
95MB.

NOTE: Do not write on the tape cartridge or attach labels to the top, bottom,
or sides of the cartridge.
Write-Protecting a Tape Cartridge
Write-protecting a tape cartridge prevents accidental erasure of information
stored on the tape. You can write-protect a tape cartridge in two ways:

Set the write-protect switch on the cartridge to the write-protect position.

Write-protect the cartridge by using operating system commands described
in your system software manuals.

Using System Options

3—13

Your system can read information on the tape regardless of the position of
the write-protect switch or whether writing is software disabled.

However,

the system cannot write data to the tape when the write-protect switch is set

to the write-protect position, or when writing is software disabled.
When you use a cartridge to install software, make sure the cartridge is
write-protected.

To write-protect a cartridge, slide the write-protect switch

toward the label slot (see Figure 3-9). Two icons on the switch indicate the
write-protect status. When the tape is write-protected, an orange rectangle is

visible next to the lower icon.

Figure 3-9:

Tape Cartridge Write-Protect Switch

) Compociopel//]

NOT WRITEPROTECTED

flh

WRITEPROTECTED

MLO-1441-87

The system recognizes the tape as being write-protected under any one of
the following conditions:
*

The write-protect switch on the cartridge is set to the write-protect
position.

An operating system command has write-protected the tape.

3—-14

MicroVAX I 630QY, 630QZ

Operation

A tape recorded on a TK50 tape drive is inserted into a TK70 drive.

Removing write-protection depends on how the tape was recorded and how
it is write-protected. You can remove write-protection on tapes recorded in a
compatible format as follows:

If the cartridge is write-protected only by the write-protect switch on the
cartridge and not the operating system, moving the switch to the writeenabled position removes the write protection. On the TK70, the orange
1:,‘}‘1.

AAAAAAA L

oot

tlan

mend

115 il 5UCD OUul dil LT Clid Ul

tlen

A mvslica
s

~camcan mazad

LT C)\CkutlllB Comimiarna.

)

tlan

TEN

<7n--

1NNVV, yuu

should unload the tape, change the switch setting, then load the tape to
make sure the drive recognizes the new write-protect status.
*

If the cartridge is write-protected only by a software command and not the
write-protect switch, removing the operating system restriction removes
the write-protection. On the TK70 drive, the orange light goes out.

If the cartridge is write-protected by both the switch on the cartridge and
a software command, you must change the switch setting and remove
the operating system restriction.

NOTE: You cannot write-enable a tape recorded in TK50 format for a TK70
tape drive either by moving the write-protect switch on the cartridge or by using
software commands. The TK70 drive always recognizes a tape recorded on a TK50
drive as write-protected.

When you use a tape cartridge to make a backup copy of files, make sure

the tape is write-enabled. On the TK70 drive the orange light should be off.
If the light is not off, check for any of the write-protect conditions described
above.

Change the switch setting and/or operating system restriction as

necessary. Do not begin your operation until the orange light goes off.
Tape Cartridge Handling and Storage Guidelines
*

Do not touch the exposed surface of the tape.

Do not drop the tape cartridge. The impact from a fall can damage the
tape cartridge.

Allow new tapes to stabilize at room temperature for 24 hours before
using them.

Place an identification label only in the label slot on the front of the tape
cartridge.

Store tape cartridges in a dust-free environment.

Using System Options

3—15

Keep tape cartridges away from direct sunlight, heaters, and other sources

of heat.

Store tape cartridges in a stable temperature between 10° and

40° Celsius (50° and 104° Fahrenheit).
®

Store tape cartridges where the relative humidity is between 20 and 80
percent.

Keep tape cartridges away from magnets and equipment that generates
magnetic

fields,

such

as motors,

transformers,

terminals,

and audio

equipment.

Keep tape cartridges away from x-ray equipment.

3.1.3.1 TK70 Tape Drive
The TK70 tape drive holds one removable COMPACTape Il or COMPACTape
cartridge. You can use a COMPACTape II or COMPACTape cartridge as an
input device to load software or data into your system. The TK70 drive can
read data on both types of cartridges written by either a TK70 drive or a
TK50 drive.

You should use

a COMPACTape II as an output device to make copies or

backups of software or data. The TK70 drive cannot write to a COMPACTape
II or COMPACTape that has been written by a TK50 tape drive.

tape drive has two primary controls:

The

the cartridge insert/release handle

(subsequently referred to as “the handle”) and the Unload button.

You use

the handle to insert or remove a cartridge and lock it into position. Pull the
handle open to insert or remove a tape cartridge. Push the handle closed to
lock a tape cartridge into position and load the tape.
You use the Unload button to rewind and unload the tape.

Unloading and

rewinding can also be controlled by software. Refer to your system software

manuals for appropriate commands.
The TK70 tape drive also has three indicator lights that let you know the

status of the drive.
*

Orange light (Write-Protected): A steady orange light indicates that the
cartridge is write-protected.

Yellow light (Tape in Use): A steady yellow light indicates that the tape
is loaded. A blinking yellow light indicates that the tape is in motion.

Green light (Operate Handle):

A steady green light indicates that you

can move the handle to insert or remove a tape. A blinking green light
indicates a cartridge load fault. You can also move the handle when the

green light is blinking.

3—-16

MicroVAX Il 630QY, 6300Z

Operation

All three lights blinking simultaneously indicates a fault condition.

Figure 3-10 shows the TK70 tape drive with the controls and indicator lights

labeled.

Figure 3—10:

TK70 Tape Drive

GREEN

YELLOW
ORANGE —

— UNLOAD

] \|
Q

S——

HANDLE

—

MLO-1442-87

To operate the drive properly, you must carefully monitor the indicator lights.
The instructions for inserting and removing cartridges, which appear later in

this section, tell you what should happen at each step. A table at the end of
the section summarizes light and control combinations.

Design of the Drive
The TK70 tape drive operates somewhat like a reel-to-reel tape deck. Inside
the drive is a take-up reel with a leader attached.
a single reel containing the magnetic tape.
]

“

vam

Inside the cartridge is

When you insert the cartridge
Apetgra

Mee

LA\_\A;L)

mmae

RSy§

uuy;\.

Using System Options

3—17

the leader in the cartridge, and the tape winds onto the take-up reel. The
coupling and winding process is called loading. When the automatic loading
process completes, the tape is ready to use.

Once the cartridge is loaded, you cannot remove it without rewinding and
uncoupling the leaders, a process called unloading. Even if you have not
used the tape, you must unload it before you can remove the cartridge. When
you press the Unload button, the tape rewinds into the cartridge and the
leaders uncouple.

Inserting a Tape Cartridge

Before you use the tape drive, make sure the system is turned on (the power
switch glows). During power-up, the TK70 drive runs self-tests that last a few
seconds. All three lights (orange, yellow, and green) come on momentarily,
then the yellow light blinks while the TK70 drive runs self-tests. At the
end of the tests, the yellow light goes off and the green light comes on,
accompanied by a short beep. The green light and the beep indicate that you
can move the handle.

CAUTION: Move the handle only when the green indicator light is on. Moving
the handle while the yellow light is on could damage the drive. If all three lights
blink rapidly at any time, a fault condition exists. Press the Unload button once.
If the fault is cleared, the tape unloads. The yellow light blinks during unloading,
then the green light comes on. If the fault is not cleared, the three lights continue
to flash. Do not attempt to use the tape drive or to remove the tape cartridge.
Call your DIGITAL service representative.

Use the following procedure to insert a tape cartridge. (See Figure 3-11.)
1.

Pull the handle open.

Position the cartridge so the arrow on the cartridge faces left and points
toward the drive. Insert the cartridge into the TK70 tape drive until you
feel the cartridge lock into place.

Push the handle closed.

The green light goes off and the yellow light blinks as the tape loads.
When the yellow light glows steadily, the tape is ready to use.

NOTE: If the green light blinks rapidly when you push the handle closed,
the drive has detected a cartridge fault.
the cartridge. Use another cartridge.

3-18

MicroVAX 1t 630QY, 63002

Operation

Pull the handle open and remove

Figure 3—11:

Inserting a Tape Cartridge into a TK70 Tape Drive

GREEN —
LIGHT
IS LIT

HANDLE —

YELLOW— T
LIGHT
BLINKS

__ARROW

MLO-1443-87

Refer to your system software manual for instructions on how to use the tape
cartridge, for example, how to load software or perform backup.
NOTE: If a cartridge is new, the drive performs a calibration sequence that
takes approximately 30 seconds when the drive receives the first command from
the operating system. The yellow light blinks rapidly and irregularly during
1e

e
Bl ok el i
vidiiUraticw.,

Using System Options

3—19

Removing a Tape Cartridge
You must unload a tape before you can remove the cartridge from the tape
drive. Use the following procedure. (See Figure 3-12.)
1.

Press the Unload button.
unload the cartridge.
appropriate command.

You can also issue a software command to
Refer to your system software manuals for the

The yellow light blinks slowly, as the tape rewinds and unloads into the
cartridge. This may take up to 90 seconds.
2.

When the yellow light goes off and the green light comes on (you also
hear a beep), pull the handle open.

CAUTION: Move the handle only when the yellow indicator light is off

and the green indicator light is on. Moving the handle while the yellow light
is blinking could damage the drive.

Remove the tape cartridge and store it in its container.

Push the handle closed.

The green light remains on, indicating that there is power to the drive
and
that you can safely move the handle.

3-20

MicroVAX 1l 630QY, 6300Z

Operation

Removing a Tape Cartridge from a TK70 Tape Drive

UNLOAD
“N. BUTTON
/%Q
|
_N\

©r

Figure 3—12:

GREEN —
LIGHT
IS LIT

GREEN—"]
LIGHT
IS LIT

MLO-1444-87

CAUTION: Remove the tape cariridge from the tape drive when the cartridge
is not in use or before you turn off the system. Failure to remove the cartridge
may damage it.

Using System Options

3—21

Summary of TK70 Tape Drive Controls and Indicator Lights
Table 3-1 summarizes the TK70 tape drive controls. Table 3-2 describes the
meaning of the indicator lights.

Table 3—1:

TK70 Tape Drive Controls

Control

Position

Handle

Open

Function
Lets

you

ter rewind

insert

remove

tape

af-

and unload operations

are com-

and

pleted.
Closed

Locks

tape

operating

position

be-

gins load sequence.

Unload button

Momentary con-

Rewinds and unloads the tape.

tact switch

Table 3—2:

TK70 Tape Drive Indicator Lights

Orange

Yellow

Green

Condition

Off

No power to the tape drive.

Off

On steadily

Safe to move handle. Power
is present.

Off

Blinking

Load

fault.

tridge

leader

fective.
dle

carde-

Pull out the han-

and

tridge.

The
may

remove

the

car-

Do not use the car-

tridge.

On/Off

On steadily

Off

Tape is loaded but not in
motion.

On/Off

Blinking

Off

Tape is in motion.

On steadily/

Off

Cartridge is write-protected.

blinking

3—-22

MicroVAX 1l 630QY, 6300Z

Operation

Table 3—2 (Cont.):

TK70 Tape Drive Indicator Lights

Orange

Yellow

Green

Blinking

Condition
.

A fault is occurring.

Press

the Unload button to unload the tape cartridge.

the fault is cleared, the yellow light blinks while the

tape

rewinds.

When

the green light comes on,
you

can

dle

tridge.

move

the

han-

remove

the

car-

If the fault is not

cleared, all three lights continue to blink.

Do not at-

tempt to remove the tape
cartridge.
ITAL

Call your DIG-

service

representa-

tive.

3.1.3.2 TK50 Tape Drive
The TK50 tape drive holds one removable COMPACTape or COMPACTape
II cartridge. You can use either type of cartridge as both an input and output
device.

Use the tape cartridge as an input device to load software or data
into your system. Use the tape cartridge as an output device to make copies
(or backups) of software or data.

The tape drive has two primary controls: the cartridge insert/release handle
(subsequently referred to as “the handle”) and the Load/Unload button. You
use the handle to insert or remove a cartridge and lock it into position. Pull
the handle open to insert or remove a tape cartridge. Push the handle closed
to lock a tape cartridge into position.

You use the Load/Unload button to control winding or rewinding of the
tape. The button is a 2-position control. When you press in the button, the
tape winds onto the take-up reel. When you press the button again, it pops
out and the tape rewinds back into the tape cartridge.

The drive also has two indicator lights that let you know the status of the
drive. A red light is part of the Load/Unload button. A green indicator light
is at the opposite end of the drive. Figure 3-13 shows the TK50 tape drive
with the controls and indicator lights labeled.

Using System Options

3—23

Figure 3—-13:

TKb50 Tape Drive

LOAD/UNLOAD
BUTTON

RED LIGHT

T HANDLE

\ GREEN LIGHT

ML.O-1445-87

To operate the drive properly, you must carefully monitor the status lights.
The instructions for inserting and removing cartridges, which appear later
in this section, tell you exactly what should happen at each step. Table
3-3 and Table 3-4 at the end of this section summarize light and control

combinations.

Design of the Drive
The TK50 drive operates somewhat like a reel-to-reel tape deck. Inside the
drive is a take-up reel with a leader attached. Inside the cartridge is a single
reel containing the magnetic tape. When you insert the cartridge and press in

the Load/Unload button, the leader in the drive automatically couples with
the leader in the cartridge, and the tape winds onto the take-up reel. The
coupling and winding process is called loading. When the automatic loading
process completes, the cartridge is ready to use.

The method of coupling the two leaders is similar to threading a needle. The
leader in the cartridge has a large eye with a notch. The leader in the drive

is arrow-shaped. (See Figure 3-14.)

3—-24

MicroVAX Il 630QY, 6300Z

Operation

Figure 3—-14:

Tape Leaders

CARTRIDGE
LEADER

ARROW
SHAPED

| |

: )
TM\

RETAINING

NOTCH

—

RELATIVE
MOTION

DRIVE
LEADER
MLO-1446-87

Loading occurs in two stages:
1.

Whenye}

nsert a cartridge, the lea er in the drive first threads through

oLl

(U913

the eye of the cartridge leader.
2.

When you press in the Load/Unload button, the take-up reel begins to
move and the drive leader catches in the notch, pulling the tape onto the
take-up reel.

Once the cartridge is loaded, you cannot remove it without rewinding and

uncoupling the leaders, a process called unloading.

Even if you have not

used the tape, you must unload it before you can remove the cartridge. When
you move the Load/Unload button to the out position, the tape rewinds into
the cartridge and the leaders uncouple.

Although rare, rough handling during shipment may dislodge either the
cartridge leader or the drive leader.

Because the position of each leader is

critical to successful coupling, you should make sure the leaders are properly
positioned.

Check the cartridge leader in the following situations:
*

When you use a cartridge for the first time. The cartridge could be blank
or could contain software.

After you drop a cartridge, since the shock can dislodge a leader.

Using System Options

3—25

When you have load/unload problems.

Check the tape drive leader in the following situations:
*

When you first install the system.

After you move the system.

When you have load/unload problems.

The following two sections explain how to check each leader.

Checking the Cartridge Leader
To check the cartridge leader, open the door in the back of the cartridge.
With your thumb, lift the door lock, as shown in Figure 3-15, and press on
the hinge. The door swings open. The tape leader should appear exactly as
shown in Figure 3-15, with most of the leader eye visible.
Figure 3—15:

Checking the Cartridge Leader

DOOR LOCK

LEADER

(RELEASE BY
LIFTING WITH THUMB)

EYE
MLO-1447-87

If no leader is visible or if the leader extends out more than is shown in
the figure, do not load the cartridge into your tape drive or try to adjust the
leader. Contact your DIGITAL service representative for another cartridge. If
the leader appears normal, close the cartridge door and proceed.

CAUTION: Using a cartridge with a mispositioned leader can damage the tape
drive.

3-26

MicroVAX Il 630QY, 63002

Operation

Checking the Drive Leader
To check the leader in the drive, look inside the drive (you may need to use
a light). You should look for two things:

The pointed end of the leader should be clearly visible and straight (not

[3]

bent up or down).

The leader shouid be hooked onto the buckling link, as shown in Figure
3-16.

Figure 3—16:

Checking the Drive Leader

BUCKLING
LNk

UW M

e ]an
kR

NOTCH IN— |

—

fi_

LEADER

—

TAKE—UP/

B—=

LEADER

HANDLE
CLOSED
MLO-1448-87

If the leader is unhooked or if you cannot clearly see the pointed end, do not
insert the cartridge into the drive or attempt to fix the drive leader. Contact
—oTi
O Wi
P UL Wi representative.
your DICITAL
L/ RNTA
service

Using System Options

3—27

CAUTION: Using a tape drive with a mispositohed leader can damage your
tape drive.
If the cartridge leader and drive leader appear normal, proceed with the next
step.

Inserting a Tape Cartridge
Before you use the tape drive, make sure the system is turned on (the on/off
switch is set to 1) and the Load/Unload button is in the unload (out) position.
The Load/Unload button glows red for approximately four seconds when you
power on your system.

When the red light goes off and the green light comes on, you can move the
handle.

CAUTION: Move the handle only when the red indicator light is off and the
green indicator light glows steadily.

Moving the handle while either indicator

light is blinking could damage your system. If the red light blinks rapidly at any
time, press the Load/Unload button four times.

If the problem persists, do not

attempt to use the tape drive or to remove the tape cartridge. Call your DIGITAL

service representative.

Use the following procedure to insert a tape cartridge. (See Figure 3-17.)
1.
2.

Pull open the handle when the green light is on.
Position the cartridge so the arrow on the cartridge faces toward the left

and points toward the drive. Insert the cartridge into the TK50 tape drive

until you feel the cartridge lock into place.
The red light comes on.

The green light goes off.

Push the handle closed.
The red light goes off.

The green light comes on.
4.

Push the Load/Unload button to the load (in) position.
The red light comes on.
The green light goes off.

3—-28

MicroVAX Il 630QY, 6300Z

Operation

Figure 3—17:

Inserting a Tape Cartridge into a TK50 Tape Drive

HANDLE

GREEN LIGHT
IS LIT

LOAD/UNLOAD
BUTTON
IN

|RED LIGHT

/ IS LT

MLO-1449-87

The tape loads in 10-15 seconds.

During loading, the two leaders couple

and the tape winds onto the take-up reel inside the tape drive. The red light
remains on during loading.

When the green light also comes on, the tape drive is ready. Refer to your

system software manual for instructions on how to use the tape cartridge, for
example, how to load software or perform backup.

NOTE: If a cartridge is new, the system performs a calibration sequence that
takes approximately 40 seconds.

The green light blinks rapidly and irregularly

during calibration.

Using System Options

3—29

Removing a Tape Cartridge
You must unload a tape before you can remove the cartridge from the tape

drive. Use the following procedure. (See Figure 3-18.)
1.

Set the Load/Unload button to the unload (out) position.
The red and green lights blink slowly, but not in unison, as the tape

rewinds to the beginning. This may take up to 90 seconds. (Rewinding
a tape can also be done under software control.

Refer to your software

manual for information.)
The red light remains on and the green light goes off as the tape unloads
into the cartridge.

When the tape is unloaded, the red light goes off and the green light
comes on.

Pull the handle open only after the green light comes on.

CAUTION: Move the handle only when the red indicator light is off and
the green indicator light glows steadily.

Moving the handle while either

indicator light is blinking could damage your system. If the red light blinks

rapidly at any time, press the Load /Unload button four times. If the problem
persists, do not attempt to use the tape drive or to remove the tape cartridge.
Call your DIGITAL service representative.
3.

Remove the tape cartridge and store it in a safe place.

Push the handle closed.

The green light remains on, indicating that there is power to the drive and
that you can safely move the handle.

3—30

MicroVAX Il 630QY, 63007

Operation

Figure 3—18:

Removing a Tape Cartridge from a TK50 Tape Drive

LOAD/UNLOAD
BUTTON OUT

HANDLE

@
GREEN LIGHT
ISLIT

Summaryv of TK50 Controls and Indicator Lights
Table 3-3 summarizes the TK50 tape drive controls. Table 3-4 describes the
meaning of the indicator lights.

Using System Options

3—31

Table 3—3:

TKb50 Tape Drive Controls

Control

Position

Handle

Open

Function
Lets you insert or remove a tape after

rewind

and

unload

opera-

tions are completed.

Closed

Locks

tape

operating

posi-

tion.

Load/Unload button

Table 3—4:

Loads the tape (10-15 seconds).

Out

Rewinds and unloads the tape.

TK50 Tape Drive Indicator Lights

Green Light

Red Light

Condition

Off

No power to the tape drive.

Off

Safe to move the handle. Power is
present.

Off

Do not move the handle.

One of

the following is in effect:
¢

Power-on

self-test

occur-

ring.
®

Cartridge is inserted but han-

dle is still open.
®*

Tape

unload-

ing.

®
On

Blinking

Tape is stopped.

Tape loaded successfully.
Tape is in motion (except rewind).
Read/write

commands

ing processed.

are

be-

Irregular fast blink-

ing means tape calibration is occurring.

Blinking

3-32

Blinking

MicroVAX [l 630QY, 630QZ

Operation

Tape is rewinding.

Table 3—4 (Cont.):

TK50 Tape Drive Indicator Lights

Green Light

Red Light

Condition

Off

Blinking rapidly

fault

occurring.

Press

and release the Load/Unload but-

ton

four

times.

the

prob-

lem persists, do not attempt to remove

the

tape

cartridge.

Call

your DIGITAL service representative.

3.2 Communications Options
The

fAllAwring
b4
-lU-llU YVili 16

Funoc

L] tl\.o

~nf
\VZ S

nommnflina{-inflc
LVRILILLL LN A LIVLO

or\lnnnc
t} LIV LD

oA
al <

artrailalla
avaliauvic

faw
iVl

tla
t1ic<T

MicroVAX II 630QY, 630QZ:

Asynchronous serial controllers

Synchronous serial controllers

Network controllers

3.2.1 Asynchronous Seriai Coniroiiers
Asynchronous controllers are available with and without modem support.

3.2.1.1 Without Modem Support
Before using any peripheral device connected to a serial communications
controller, check the following:
i.

~l
Ter ~Ansnsnan~
1MiakKe sure |.u€ Pcuyucu:u
uc‘vuc is BroDEr
prope 1_y
COonnec
T\ —.Ln

explained in MicroVAX II 630QY, 630QZ Installation.

Make sure the peripheral device is properly installed, plugged into an
appropriate power source, and turned on.

Make sure the device is properly set up. Set-up involves choosing how
the device operates. Some set-up choices are matters of personal choice,
for example, the number of columns that display on a terminal screen.
Others, such as baud rate (a measure of the speed at which data is
transmitted over a data line), must match the system setting, if the device
and system are to communicate. Refer to your terminal or printer manual

for set-up instructions.

Generally the default settings for your terminal

should be acceptable.

Using System Options

3—33

A sample set-up for a VT200-series terminal follows:
1.

Press

to display the Set-Up Directory Screen.

Choose the

Default option. Default correctly sets all values, except line speed.
2.

Choose the Comm option to display the Communications Set-Up
Menu. Choose the Transmit option and change the speed to 9600 to
match the system setting. Set Receive equal to Transmit.

Choose the Return to Set-Up Directory option.

Choose the Save

Set-Up option to store the set-up values.
Your operating system may have other requirements for using serial devices.
Refer to your system software manuals.

3.2.1.2 With Modem Support
Using serial controllers with modem control support requires that you install
two modems: one connected to the system and one connected to the remote
terminal. Both must be connected to phone lines.
Before you can use modems with your system, check the following:
1.

Make sure each modem is connected to the system, as explained in

MicroVAX 11 630QY, 630QZ Installation.
2.

Make sure the modem is properly installed and connected to a phone

jack.
3.

Set controls on the modem according to instructions in the modem user’s
guide.

Before you can use the modem connected to the remote terminal, check the
following;:
1.

Make sure the modem is properly installed and connected to a phone

jack.
2.

Set controls on the modem according to instructions in the modem user’s
guide.

Check the settings on the terminal attached to the modem.

Depending

on the type of modem and type of lines used, the baud rate may be 300,
1200, or 2400.

Other settings should be the same as those described in

the previous section.
Before using a line with modem control support, you must set certain system

software parameters, such as line speed. See your system software manuals
for details.

3—34

MicroVAX 1l 6300QY, 63007

Operation

3.2.2 Synchronous Controllers
Before using a synchronous controller you must verify the following:
The system you want to communicate with has an appropriate
synchronous controller.
Synchronous communications require a
synchronous controller on both the transmitting and receiving systems.
Both the transmitting and receiving systems must have supporting host
software installed. Synchronous communications operate under specific
protocols that define how data is interpreted. Two common protocols
are X.25 and PSI. Appropriate host software is required to interpret the
protocol.

3.2.3 Network Controllers
Be fore using a network controiler, you must do the following:
1.

Make sure the transceiver cable connected to the DEQNA or DELQA
module in the system is properly connected to the network in one of the
following ways:

To an H4000 transceiver located on a traditional Ethernet.

To a DELNI, which can be connected to a larger Ethernet or which
can serve to connect up to eight systems in a local area network.

To a DESTA, an adapter that enables you to connect to a ThinWire
Ethernet.

Have the DECnet application installed on your system.

Refer to your system software manuals and DECnet manuals for other
requirements and further instructions on using a network connection.

3.3 Real-Time Controllers
Before using a real-time controller, make sure the devices connected to the
controller are properly set up. Refer to documentation for the real-time
device.

Using System Options

3—35

3.4 Printer Options
Before using a printer, make sure it is properly set up and passes any

self-tests.

Verify that the printer is connected to an appropriate controller.

Some printers, such as the LP25/26/27 and LG01/02, require the LPV11
interface. Other printers require modem control signals. Consult your printer

documentation for the interface requirements.

3.5 Adding New Options
If you have available slots, you may be able to add new modules to your
system. Possible limitations to adding new modules include the following;:
*

Power limitations

Physical space limitations

Bus limitations (ac/dc loading)

Your DIGITAL sales representative can advise you about modules available for

your system and what you need to order. A DIGITAL service representative
should perform the installation, as the system must be properly configured
to work correctly.

CAUTION: Do not attempt to remove, rearrange, or install new modules.
Contact DIGITAL Service for assistance. If you want to perform maintenance on
your system, you should purchase the MicroVAX Systems Maintenance Guide.

3-36

MicroVAX Il 6300Y, 6300Z

Operation

Appendix A

Related Documentation

A-1

Glossary
Application program

A program designed to meet

specific user

needs, such as a program that

monitors a manufacturing process
Backplane

The connector block that all MicroVAX II printed circuit boards plug into.
A printed circuit board containing the bus.
Back up

The process of making copies of the data stored in your disk drive(s) so that
you can recover that data after an accidental loss. You make these copies on

a tape cartridge and then store it in a safe place.

Baud rate

The speed at which signals are transmitted serially along a communication

line. One baud equals one bit per second.
Binary

A number system that uses only two digits: 0 and 1. These digits are usually
represented in circuitry by two voltage levels.
Bit

A binary digit, the smallest unit of information in a binary system of notation,
designated as a 0 or a 1.
Boot

To use a bootstrap program to start a computer system.
Bootable medium

A fixed disk or magnetic tape containing software (such as an operating
system) that the bootstrap program can load into the system memory.

Glossary—1

Bootstrap

A program that you start when you turn on the MicroVAX II. The bootstrap
loads software contained on a fixed disk or magnetic tape cartridge into
memory. The MicroVAX II then stops executing the bootstrap and starts
executing the software in memory. The software usually loads an operating
system or other software into memory, so that the MicroVAX II can start
processing.
Bug

An error in the design or implementation of hardware or software system
components.

Bus

A printed circuit board that is part of the backplane.

The bus permits

communications among the other printed circuit boards.
Byte

A group of eight binary digits (bits). A byte is one-half the size of a MicroVAX
Il word and one-quarter the size of a MicroVAX II longword.
Central processing unit (CPU)

The part of a computer system that controls the interpretation and execution
of instructions.
Command

An order given by a user to a computer, often through a terminal keyboard.
Communication line

A cable along which electrical signals are transmitted. MicroVAX II systems
or devices connected by communication lines can share information and
resources.

Computer system

A combination of computer hardware, software, and external devices that
performs specific operations or tasks.
Console terminal

The

terminal you

use when installing software

and running diagnostic

programs.

Controller

A MicroVAX 1I component that regulates the operation of one or more
peripheral devices. Controllers are often called interface units.

Glossary—2

CPU

See Central processing unit
Data

A representation of facts,
concepts,
or instructions,
suitable for
communication, interpretation, or processing by human beings or by
machines.
A

Data transmission

The

movement

data,

the

form

electrical

signals,

along

communication line.
Debug

To detect, locate, and correct errors (bugs) in system hardware or software.
Device

The general name for any entity connected to the MicroVAX II that is capable
of receiving, storing, or transmitting data.
Device name

The name by which a device or controller is identified within a MicroVAX II
system. You use the device name to refer to that device when communicating
with the system.
Diagnostic program

A program that detects and identifies abnormal MicroVAX II hardware
operation.
The MicroVAX Diagnostic Monitor software contains several
diagnostic programs.
lel\
fal.

A flat circular plate with a coating on which data is stored magnetically in
concentric circles (tracks).
Disk drive

A device that contains a fixed disk or one or more diskettes. The drive
contains mechanical components that spin the disk or diskettes and move the
read /write heads that store and read information on the surface of the disk
or diskettes.
EIA

Electronic Industries Association.

Glossary—3

Error message

A message displayed by the MicroVAX II to indicate it has detected an error

or malfunction.
File

A collection of related information treated by the computer as a single item.
Firmware

Software instructions stored in a fixed form, usually in read-only memory
(ROM). In a MicroVAX system, the power-on self-tests and bootstrap program

are firmware.
Formatted data

Data laid out in a particular pattern to conform to a predetermined structure.
The structure is dictated by the system software.
Hardware

The

physical

components—mechanical

and

electrical—that

make

computer system. Compare Software.
Head

The part of a fixed-disk drive, diskette drive, or tape drive that reads, records,
and erases data. Also called read/write head.
Input device

A piece of equipment used to transfer data into the computer. A keyboard is
an input device.
Input/Output (I/O0) device

A piece of equipment that accepts data for transmission both to and from a
computer. A terminal is an input/output device.
Interactive

The method of communicating with a computer system. You type a command

at the keyboard, the system executes the command, and then responds with
a message or prompts for another command.
Interface

A device or piece of software that lets different components of a computer
communicate with one another.
1/0

Abbreviation for input/output.

Glossary—4

Kbyte

Abbreviation for 1024 bytes.
LED

Light emitting diode. A LED on the CPU cover panel displays a countdown
during the power-on sequence.

1. To move software, usually from a peripheral device into memory.
2. To place a disk in a disk drive, or tape in a tape drive.
Longword

A group of 32 bits, equal to two words or four bytes.

A long strip of plastic coated with magnetic oxide, used for storing data.
Often called magtape. The tape contained in a tape cartridge.
Mbyte

Abbreviation for 1,048,576 bytes.
Memory

The area where a computer finds the instructions and data it will process.
Menu

A displayed list of options.

The list usually contains commands you can

enter.

Off-line

Pertaining to equipment, devices, and events that are not under direct control
of the computer system.
Operating system

A collection of programs that controls the overall operation of a computer
and performs such tasks as:

Assigning places in memory to programs and data

Processing requests, scheduling jobs

Controlling the operation of input and output devices

Glossary—5

Output device

A device by means of which data can be extracted from a computer system;

for example, a printer.
Peripheral device

Any device distinct from the central processing unit that provides it with
additional memory storage or communication capability. Examples are disk

and diskette drives, video terminal, and printers.
Power-on sequence

A series of ordered events that occurs when you supply power to a system

by turning it on.
Printer

A peripheral device that provides paper copies of information stored in a
computer.

Program

The complete sequence of instructions necessary for a computer to perform a
task. See Software.
Prompt

A character or words that a computer displays to indicate it is waiting for
you to type a command.

Read-only memory (ROM)

A memory that does not allow modification of its contents.
can use data in a ROM but cannot change it.

The computer

Reboot

To restart a computer system.
MicroVAX II system.

Pressing the Restart button reboots the

Record

A set of related data that a program can treat as a unit. A file consists of a
number of records.
ROM

See Read-only memory.

Glossary—6

Run

1. A single continuous execution of a program.
2. To execute a program.
Software

Programs executed by a computer system to perform a chosen or required
function. Compare Hardware.
Software package

A set of related programs that performs a specific task.
Storage medium

Any device capable of recording information, for example, a tape cartridge.
Store

To enter data into a storage device, such as a disk, or into memory.
System

A combination of computer hardware and software and external devices that
performs specific processing operations.
Svstem management

Tasks performed by the operating system to control the overall operation of
the computer system.
Terminal

An input/output device generally used for communication between the users
of a computer system and the system itself.
Video terminal

A terminal that displays information on the screen of a cathode ray tube
(CRT).
Word

A word is 16 bits long.
Write-protect

To protect a disk, diskette, or other storage medium against the addition,
revision, or deletion of information.

Glossary—7

Index
A

Communications controllers (cont’d.)

Alr circulation in system, 1-10

Console serial line unit (SLU)

Asynchronous serial controllers
function, 1-11
types, 1-11
using, 3-33

with modem support, 1-12, 3-34
without modem support, 3-33

with modem support, 1-12
function, 1-8
Console terminal connector, 1-6
Control panel
controls and indicators, 1-3

Controls
for fixed-disk drive, 1-5

Autobooting the system, 2-4

on the CPU panel, 1-5
on the front control panel, 1-3

TK50 tape drive, 3-23

BA23 enclosure, 1-1
Base system components, 1-7

BOOT command
uses, 2-6

Booting from console mode, 2-5
Booting the system

autobooting, 2—-4
from console mode, 2-5

TK70 tape drive, 3-16

CPU panel controls, 1-5

D
DC OK light
function, 1-5, 1-10

Diagnostic software
running, 2-1
Diskettes

inserting into RX33 drive, 3-10
inserting into RX50 drive, 3-8

Calibrating a tape cartridge

proper handling, 3-3

for TK50 tape drive, 3-29

storing, 3-3

for TK70 tape drive, 3-19
Cartridge leader

how to check, 3-26
when to check, 3-25

write-protecting, 3-6
Diskless systems, 1-1
Drive leader

how to check, 3-27

Central processing unit (CPU)
function, 1-8

Communications controllers
asynchronous, 1-11, 3-33
function, 1-11
network controllers, 1-12, 3-35

E
Error messages

at power-on, 2-3

synchronous, 1-12, 3-35
types, 1-11, 3-33

Index—1

LED display
on the CPU panel, 1-6

Fans

function, 1-10
Fixed Disk 0
controls, 3-1

Fixed-disk drive
controls, 1-5

Load/Unload button
on TK50 tape drive, 3-23

Loading system software
with BOOT command, 2-6
Loop Back Test Mode
setting of Power-Up Mode switch,

function, 1-9

1-6

Front view of system, 1-2

H
Halt button

Main memory
contents, 1-8

function, 1-4

function, 1-8

settings, 1-4

Halt Enable/Disable switch
function, 1-5
settings, 1-5

Halting the system, 2-7

size, 1-8

Mass storage controllers
function, 1-9
Mass storage devices

fixed, 1-5

description, 2-7

function, 1-9

Handle

removable, 1-5, 1-9

on TK50 tape drive, 3-23

on TK70 tape drive, 3-16

types, 1-5, 1-9
Mass storage options

types, 3-1

Modems

function, 1-12

Indicator lights
on TK50 tape drive, 3-23

types, 1-12

using, 3-34

on TK70 tape drive, 3-17
Inserting a tape cartridge

Modem support
description, 1-12

into TK50 tape drive, 3-28

full, 1-12

into TK70 tape drive, 3-18

Inserting diskettes
into RX33 drive, 3-10
into RX50 drive, 3-8
Insert panels

function, 1-7

limited, 1-12

N
Network controllers
function, 1-12

types, 1-7

using, 3-35
New system

using, 2-1

Labeling a tape cartridge, 3-12
Language Inquiry Mode

setting of Power-Up Mode switch,
1-6

Index—2

o)
Optional components in system, 1-11

Overview of system, 1-1

RX33 diskette drive (cont’d.)

Pedestal mount, 1-1

RX33 diskettes

Power-on indicators

description, 3-9
capacity, 3-9

normal, 2-3
Power-on self-tests
description, 2-4

formatting, 3-9
RX50 diskette drive

description, 3-6

Power supply

identification of two drives, 3-6

function, 1-10
Power-Up Mode switch
function, 1-5

indicator light, 3-6
RX50 diskettes
capacity, 3-7

settings, 1-5

Printer interfaces
function, 1-13
Printer options

using, 3-36

S
Setting up

serial devices, 3-33
Shutdown procedure
when turning off system, 2-7

Rack mount, 1-1

Switch settings, 2-1
normal operation, 2-2

RD50-series fixed-disk drives
description, 3-1

Ready button

special operation, 2-2
Synchronous controllers
function, 1-12

function, 1-4, 3-2

protocol, 1-12

settings, 1-4, 3-2

Real-time controllers
function, 1-12

using, 3-35

System components

base system, 1-8

using, 3-35

Rear view of system, 1-5
Related documentation, A-1
Removable mass storage devices

uses, 1-9
Removing a tape cartridge

from TK50 tape drive, 3-30
from TK70 tape drive, 3-20
Restart button
function, 1-4
Restarting the system

description, 2-7
Run indicator

function, 1-5
Run Mode

setting of Power-Up Mode switch,
1-6

RX33 diskette drive

Tape cartridge

calibrating for TK50 tape drive,
3-29

calibrating for TK70 tape drive,
3-19
handling instructions, 3-15

inserting into TK50 tape drive,

3-28
inserting into TK70 tape drive,
3-18
labeling, 3-12

removing from TK50 tape drive,
3-30
removing from TK70 tape drive,
3-20

Index—3

Tape cartridge (cont’d.)

storage guidelines, 3-15
write-protecting, 3-13

write-protect switch, 3-14
TK50 controls and indicator lights,
3-31
description, 3-23

design, 3-24

indicator lights, 3-23

VAXclusters, 1-1

summary of controls, 3-31

summary of indicator lights, 3-32
TK70 tape drive, 3-16

function, 1-4, 3-2

controls, 3-16, 3-22

settings, 1-4, 3-2

indicator lights, 3-17

Write-protecting

operation, 3-17

summary of indicator lights, 3-22

Turning on the system, 2-3

W
Write-Protect button

access to, 3-16

Turning off the system, 2-7

on the TK70 tape drive, 3-16
Using a new system, 2-1
Using the system, 2-1

TK50 tape drive

uses of, 3-16

Unload button

a tape cartridge, 3-13
diskettes, 3-6
Write-protect switch

on a tape cartridge, 3-14
Write-protect tab
for diskettes, 3-6

Index—4

MicroVAX11630QY,630QZ

Troubleshooting

Order Number EK—-O04AB-SG-002

digital equipment corporation
maynard, massachusetts

December 1986
September 1987

The information in this document is subject to change without notice and should not be construed as a

commitment by Digital Equipment Corporation.

Digital Equipment Corporation assumes no responsibility for any errors that may appear in this

document.

The software, if any, described in this document is furnished under a license and may be used or
copied only
in accordance with the terms of such license. No responsibility is assumed for the use or reliability
of software
or equipment that is not supplied by Digital Equipment Corporation or its affiliated companies.

The READER’S COMMENTS form on the last page of this document requests the user’s critical evaluation
assist in preparing future documentation.

The following are frademarks of Digital Equipment Corporation:

COMPACTape

MASSBUS

DEC

MicroVAX

ULTRIX

DECmate

PDP

UNIBUS

ThinWire

DECnet

P/OS

VAX

DECUS

Professional

VAXcluster

DECwriter

Q-bus

VAXELN

DELNI

Rainbow

VMS

DEQNA

RSTS

DESTA

RSX

Work Processor

DIBOL

Eflmfluflu TM

ML-5811

FCC NOTICE:
energy.

The equipment described in this manual generates, uses, and may emit radio frequency

The equipment has been type tested and found to comply with the limits for

device pursuant to Subpart ] of Part 15 of FCC Rules, which are designed to provide

a Class A computing

reasonable protection

against such radio frequency interference when operated in a commercial environment.
Operation of this
equipment in a residential area may cause interference, in which case the user
at his own expense may be
required to take measures to correct the interference.

Contents
Preface

Chapter 1

Troubleshooting During Power-On

Chapter 2

Troubleshooting During Normal Operation

Chapter 3

Running the MicroVAX Diagnostic Monitor
(MDM)

3.1

Starting MDM . ... ...

3.1.1

RX50 Imstructions

3.1.2

TK50/TK70 Instructions . .

32
3.21

3-2

. . . ........
..
...

3-3

e e

3-7

MainMenuOptions . ..........................

3-11

. ... ........
... ... ... ... ....

3-12

3.2.2

Display System Configuration and Devices . . . ........

3-16

3.2.3

Display the Utilites Menu

. ....................

3-18

3.2.4

Display the ServiceMenu . . . ...................

3-23

3.2.5

Exit MDM . . . . ...

3-23

Index

Testthe System

Figures

MDM Introductory Display . . . . ...................
Preparing for Testing Message . . . ... ...............
Diskette Removal Display. . ... ...................

3-4

Ready for Testing Message . . . ... .................
MDM Introductory Display . . . ........ e

3-7
3-9

3-10

3-7

Preparing for Testing Message . . ... ................
Ready for Testing Message . . ... ..................

3-8

MDMMainMenu

.
..............

3-12

3-9

SystemTestScreen............................

3-13

3-10 Begin Device Tests Screen . ... ...................

3-14

3-11

Device Failure Screen .. ........................

3-15

3-12

System Test Passed Screen . . .. ...................

3-16

3-13

Sample System Configuration and Devices Display .. ... ..

3-17

3-14

System Utilities Screen

. .. ......................

3-19

3-15

Formatting Utility Warning Screen . . . .. .............

3-20

3-16

Listof Drivesin System.

. .......................

3-21

3-17

Formatting Messages . . . ... .........
...
...

3-22

3-18

Formatting Success Message . . ... .................

3-23

3-19

ExitDisplay

3-24

3-1

3-2
3-3
3-4

3-5

3-6

........ ... ..

3-5
3-6

3-11

Tables
1-1

Troubleshooting Power-On Problems . ...............

1-2

2-1

Troubleshooting Operation Problems

2-1

. ...............

Preface
A

LVAMILRLIVUVRALD

your system. When you
11 630QY,
VIUN

630Q7
Oper
Vs VN
e

the problem.

This manual is divided into three chapters:
®

Chapter 1 describes problems you may experience at power-up-and
corrective actions.

Chapter 2 describes problems you may have during normal operation of
your system and corrective actions.

Chapter

describes

the

MicroVAX

Diagnostic

Monitor

(MDM),

diagnostic tool you can use to test your system periodically or to isolate
a particular probiem.
The troubleshooting techniques described in this manual do not identify all

possible problems with your system, nor do the actions suggested remedy
all problems. If the actions suggested do not solve the problem, call your
DIGITAL service representative.

Chapter

Troubleshooting During Power-On
Whenever you power on your system, the MicroVAX II processor performs a

series of self-tests and start-up routines. After successful completion of the
self-tests, the system attempts to load system software. MicroVAX II 630QY,
630QZ Operation describes the display you see during the normal power-on
sequence.

A countdown from F (15 in hexadecimal numbers) to 0 occurs during the

normal sequence. Only the hexadecimal portion from 7 to 0 displays on the
console terminal screen.

The full countdown displays on the light emitting

diode (LED) on the central processing unit (CPU) panel.

The countdown

sequence has three major parts:

From F through 8, the system performs internal tests.

From 7 through 3, the system tests memory and the CPU.

From 2 through 0, the system loads system software.

When attempting to autoboot, the system looks for bootable software on the
following devices in the order shown below:
1.

RX50 diskette

RD50-series of fixed-disk drive

TK50/TK70 tape cartridge

Ethernet adapter

Normally, your system boots from system software installed on a fixed disk.
However, when you install system software or run diagnostic software, the
system boots from either an RX50 diskette or a tape cartridge.
NOTE: If you have a diskless system that is part of a local area network (LAN),
you must obtain the MicroVAX II Ethernet Server Customer Diagnostics Kit
to run the MicroVAX Diagnostic Monitor (MDM). Contact your DIGITAL sales
representative to order the MicroVAX II Ethernet Server Customer Diagnostics
Kit.

Troubleshooting During Power-On

If you have a diskless system that is not part of a LAN, you cannot run MDM.
Contact a DIGITAL service representative to diagnose problems on a diskless

system that is not part of a network.
If you do not observe this sequence, refer to the possible problems and
corrective actions described in Table 1-1.

Table 1-1:

Troubleshooting Power-On Problems
Possible Cause

Problem

Corrective Action

Problems During Self-Tests
No

response

when

the on/off switch is

System is not plugged

Set the on/off switch to 0. Plug in

in.

the system.

turned on (switch is

Set the on/off switch

to 1.

not lit).
No power at the wall

Use

outlet.

check

the

trolling

power

different

wall

circuit

outlet,

breaker

con-

the

wall

out-

System circuit breaker

Set the on/off switch to 0.

Re-

set the circuit breaker (located be-

let.

the

out

posi-

low the power cable plug in the

tion.

rear

the

ing

in.

switch

cuit

breaker

system)
Set

by
the

If
trips

pushon/off

the

cir-

again,

«call

your DIGITAL service representative.

Power cable is incor-

Set the on/off switch to 0.

rectly installed.

that the cable is fully seated in the

Check

socket. Set the on/off switch to 1.
The system has power

Console

(the on/off switch is

turned off.

terminal

Turn on the console terminal.

Put

the

fer

set to 1), but no dis-

play appears on the
console terminal.
Console

terminal

off-line.

terminal

the

tion for instructions.

1—-2

MicraVAX I 630QY, 630QZ Troubleshooting

on-line.

terminal

Re-

documenta-

Table

1-1 (Cont.):

Problem

Troubleshooting Power-On Problems
Possible Cause

Corrective Action

Console terminal ca-

Make

ble is not installed cor-

stalled properly at both ends.

sure

the

«cable

in-

rectly.

Baud

rate

setting

the

system

and

the

terminal do not match.

Set the terminal baud rate to match

the system.

The normal operat-

ing setting is 9600.

Power-Up Mode switch

Set

on the CPU panel is

cated by an arrow).

the

switch

Run

(indi-

set to T.

Terminal is defective.

Run MDM diagnostics to check sta-

tus of the terminal.
The

self-tests

haited

before reaching 7.

Check the LED dispiay on the CPU

panel. If an FE,D,CB,A, 9 or 8 displays, the system has detected an
internal

error.

ber and

call your DIGITAL

Copy

the

num-

ser-

vice representative.

The

self-tests

halted

The

system

detected

between 7 and 3 and

an error message dis-

ing the CPU or mem-

played

ory.

the

con-

error

while

test-

Copy the number of the error message and call your DIGITAL service representative.

sole terminal.

General Problems During Boot Sequence
Instead
ically

automat-

starting,

sys-

Halt

Enable/Disable

switch is set to the en-

tem power-on resulis

ab]o

dis-

system

con-

sole mode.

>>>

played

being

the

nAaciHiAn
tJ\J

ALIV/LL,.

T]-\o
ALiC

con-

autoboot,

exit

console

mode

by setting the Halt Enable/Disable
witch (located on the CPU panel)

the

disable

(left)

position.

Restart the system by pressing the

sole terminal.

Restart button, located on the control

panel.

sole mode,

boot from

con-

use the BOOT com-

mand (BOOT device-name).
The message “?54
RETRY”

the

appears

console

No
on

termi-

Dbootable

was found.

media

See

actions

the

boot

listed

device

below

you

are

for

us-

ing.

nal twice.

Troubleshooting During Power-On

Table 1-1 (Cont.):
Problem

Troubleshooting Power-On Problems
Corrective Action

Possible Cause

Problems Booting from a Fixed Disk
The countdown con-

tinues
0;

from

The

system disk
write-protected.

Set the write-protect switch to the
out (write-enabled) position.

operat-

however,

ing system error mes-

sages display on the
console terminal.

The countdown does
not continue from 2
through 0, even though

Set the Ready button to the out po-

The system disk is offline.

sition (glows green).

The system disk con-

Install system software.

the Halt Enable /Disable
switch is set to dissage

DEVOF-

“?4D

FLINE”

the

mes-

The

able.

appears

console

termi-

nal.

The countdown does
not continue from 2
through 0, even though

tains no bootable system software.

the Halt Enable/Disable
switch is set to disable.

The

mes-

sage “?42 NOSUCH-

FILE” appears on the
console terminal.

The countdown does
not continue from 2

A problem exists with
the controller or fixed

through 0, even though

disk.

the Halt Enable /Disable
switch is set to disable.

The message

“?24C CTRL ERR” appears

the

con-

sole terminal.

1—4

MicroVAX I 630QY, 6300Z Troubleshooting

Run

the

MDM

scribed in Chapter 3.

software

de-

Table 1-1 (Cont.):
Problem

Troubleshooting Power-On Problems
Possible Cause

Corrective Action

Problems Booting from a Diskette
System does not boot

No diskette in diskette

Insert a diskette containing startable

(the countdown does

drive.

system software into the diskette

not continue from 2
to

drive.

or boots from

another

device

wrong

software

ap-

pears

con-

the

(the

sole terminal).
Diskette drive door is

Close the diskette drive door.

not closed.

Digkette is in the drive
upside down.

Check that the crange stripe on the
diskette matches the stripe on the
drive.

Diskette is not bootable

(does

not

contain

bootstrap program).
Diskette

worn

Use a diskette containing a bootstrap program to start system software.

Try another diskette.

damaged.

Problems Booting from a Tape Cartridge
System does not boot

No tape cartridge in

Insert a cartridge containing sys-

(the countdown does

the tape drive.

tem software into the tape drive.

not continue from 2
to 0)

or boots

from

another

device

WIONg

software

ap-

pears

con-

the

(the

sole terminal).
Fixed-disk drive is on-

Push in the Ready button to place

line

the fixed disk off-line.

(Ready

lit).

tem

starts

button

Your

sys-

from

the

fixed disk, if it is online.

Troubleshooting During Power-On

Table 1—-1 (Cont.):
Problem

Troubleshooting Power-On Problems
Possible Cause

Corrective Action

Tape is not bootable
(does

not

contain

Use a tape containing a bootstrap program to start system soft-

bootstrap program).

ware.

Tape is worn or dam-

Try another tape cartridge.

aged.

1—6

MicroVAX |l 630QY, 630QZ Troubleshooting

Chapter 2

Troubleshooting During Normal
Operation
Problems that occur during normal operation of your system may result from
a defect in the system, from faulty settings, or from incorrect procedures.
Table 2-1 lists problems, possible causes, and corrective actions. If the actions
listed do not solve the problem, call your DIGITAL service representative.

Tabie 2—-1:

Troubleshooting Operation Problems

Problem

Possible Cause

Corrective Action

The system has be-

Set the on/off switch to 0. Plug in

System Problems

System

loses

power

during operation.
Lights on control panel
are off.

the system.

come unplugged.

Set the on/off switch

to 1.

No power at the wall
outlet.

Use a different wall outlet, or
check the circuit breaker controlling power to the wall outlet.

System circuit breaker
is

the

out

posi-

Set the on/off switch to 0.
Reset the circuit breaker (located below the power cable plug on the
back of the system) by pushing it in.
Set the on/off
switch
to
1.
If the
cir-

tion.

cuit

breaker

trips

again,

call

your DIGITAL service representative.

Power cable is incor-

Set the on/off switch to 0.

rectly installed.

that the cable is fully seated in the

Check

socket. Set the on/off switch to 1.

Troubleshooting During Normal Operation

2-—1

Table 2—-1 (Cont.):

Troubleshooting Operation Problems

Problem

Possible Cause

The system loses power

The power supply has

Check

during operation.

failed.

cated on the control panel. An un-

Corrective Action
the

light

lo-

lit DC OK light indicates a power
supply problem. Turn off your system and call your DIGITAL service representative.

unex-

The

pectedly during nor-

System

halts

the

mal operation.

nal was pressed inad-

able (left) position to prevent recur-

vertently.

rences. Press the Restart button (on

The

console mode prompt
>>>

displays

key

console

termi-

Set the Halt Enable/Disable switch
on

the

CPU

panel

the

dis-

the control panel) to restart the sys-

the

console terminal.

tem.

Fixed Disk Problems
Fixed
ror

disk

write

message

er-

Disk is write-protected

Press and release Write-Protect but-

dis-

(Write-Protect

ton (not lit).

played.
Fixed
ror

button

glows orange).
disk

read

er-

Disk

be-

Press and release the Ready button

message

dis-

cause the Ready but-

(glows green) to put fixed disk on-

ton is in (not lit).

line.

Disk is write-protected

Press and release Write-Protect but-

(Write-Protect

button

ton (not lit).

Insert a diskette into the drive.

played.

off-line

glows orange).

Diskette Drive Problems
Diskette

read

error

message is displayed.

diskette

the

diskette drive.

Diskette drive door is

Close the diskette drive door.

not closed.

Diskette is in the drive

Check that the orange stripe on the

upside down.

diskette matches the stripe on the
drive.

Diskette is not format-

Use a preformatted RX50 diskette.

ted.

Diskette

worn

damaged.

2—-2

MicroVAX Il 630QY, 6300Z Troubleshooting

Try another diskette.

Table 2—-1 (Cont.):

Possible Cause

Problem
Diskette

Troubleshooting Operation Problems

write

error

message is displayed.

diskette

Corrective Action
the

Insert a diskette into the drive.

diskette drive.
Diskette drive door is
~L

Close the diskette drive door.

C1UdCU.

Diskette is in the drive
upside down.

Check that the orange stripe on the
diskette matches the stripe on the
drive.

Diskette is not format-

Use a preformatted RX50 diskette.

ted.

Diskette

worn

Try another diskette.

damaged.
Diskette is write-

Remove the write-protect tab.

protected.

TK70 Tape Drive Problems
Green

light

blinks

rapidly after you in-

Tape cartridge leader

Pull

is defective.

move

sert the tape.
Orange,

yellow,

the

handle

the

open

cartridge.

and

re-

Use

an-

other cartridge.

and

green lights blink in

A problem with the

Press

the

button

once.

drive.

orange

and

green

lights

and

the

yellow

light

the

unison.

out

blinks,
ing.
on

Unload

the

cartridge

unload-

When the green light comes
and you hear the beep,

move the tape cartridge.

re-

If all

three lights continue to blink after

you

ton,
Do

the
not

tridge.

press

the

fault

try

Unload

not

remove

but-

cleared.
the

car-

Call your DIGITAL ser-

vice representative.

Handle does not move.

Power-on test is still
in progress.

If you are trying to insert a car-

tridge, wait for the orange and yellow lights to go off and the green
light to remain on steadily.

Then

try again.

Troubleshooting During Normal Operation

2—3

Troubleshooting Operation Problems

Table 2—-1 (Cont.):

Possible Cause

Problem

Tape

drive

Corrective Action

ac-

Handle does not lock.

Do not attempt to move the handle while the yellow light is on.

tive.

Cartridge

not

in-

serted properly.

Reinsert the tape cartridge.
problem persists,

If the

call your DIGI-

TAL service representative.

Cartridge does not un-

Unload button is not

Try unloading the cartridge with

load

working properly.

software

command.

Re-

fer to your system software manu-

als.
TK70

passes

power-

The

controller

may

on self-test but does

be bad,

or the con-

not work.

nection

between

drive

and

the

Run MDM software,

described in

Chapter 3.

the
con-

troller may be loose.

TK50 Tape Drive Problems
TK50 red light blinks

rapidly,

the tape drive.

but

un-

problem

exists

Press the Load/Unload button four

times.

usual sounds occur.

the

problem

per-

sists, do not attempt to use the tape
drive or to remove the tape car-

tridge, if loaded.

Call your DIGI-

TAL service representative.

Red light blinks rapidly

Leaders are not cou-

Immediately

turn

off

the

sys-

and you hear a whirring pled properly.

tem by setting the on/off switch

sound.

to 0 (off). Call your DIGITAL service

representative.

not

at-

tempt to remove the cartridge.

Cartridge release han-

Power-on test is still

If you are trying to insert a car-

dle does not move.

in progress.

tridge, wait for the red light to go
out and the green light to come on

steadily. Then try again.
Tape

drive

ac-

Do not attempt to move the han-

dle until the red light is off and the

tive.

green light is on steadily.

Cartridge release han-

Cartridge

dle does not lock.

serted properly.

not

in-

Reinsert the tape cartridge.

TAL service representative.

2—4

MicroVAX |l 630QY, 6300Z Troubleshooting

If the

problem persists, call your DIGI-

Table 2—-1 (Cont.):

Troubleshooting Operation Problems
Corrective Action

Possible Cause

Problem

button

Make sure the Load/Unload but-

Cartridge does not un-

Load/Unload

load

is in the load (in) po-

ton is in the unload

sition.

tion. Wait for the red light to go out

(out) posi-

and the green light to come on before

trying

remove

PR
uie

<
car-

tridge.
Load/Unload

button

If you are trying to remove a car-

is not working prop-

tridge,

erly.

ing

the

try

cartridge

again.

and

unload-

the

Load/Unload

button

Set
to

the

load (in) position for a few seconds, then press it again to the unload (out) position.

tridge

release

Move the car-

handle

only

af-

ter the red light goes off and the
green light comes on.

If the prob-

lem persists, call your DIGITAL service representative.
TK50

passes

power-

The

controller

may

on self-test but does

be bad,

or the con-

not work.

nection

between

drive

and

the

Run

the

MDM

software,

de-

scribed in Chapter 3.

the
con-

troller may be loose.

Troubleshooting During Normal Operation

2-5

Chapter 3

Running the MicroVAX Diagnostic
Monitor (VIDM)
The MicroVAX Diagnostic Monitor (MDM) is a software package containing
diagnostic tests designed to isolate and identify faults in your system. The
diagnostic tests are packaged with your system on either RX50 diskettes
(labeled MV DIAG CUST RX50) or a TK50 tape cartridge (labeled MV DIAG
COTICT

CuUol

TEN

1RJV).

If you have a diskless system that is part of a local area network (LAN), you
must obtain the MicroVAX II Ethernet Server Customer Diagnostics Kit to
run MDM.

NOTE: If you have a diskless system that is not part of a LAN, you cannot run
MDM. Call your DIGITAL service representative.

The MicroVAX II Ethernet Server Customer Diagnostics Kit enables you to
install MDM software on a host VAX/VMS or MicroVMS operating system
and down-line load MDM to other systems that are part of the LAN using
the DECnet/Ethernet network facilities. When MDM is down-line loaded to
target systems from a host system, the time required to load MDM is reduced
significantly.

Call your DIGITAL sales representative to order the MicroVAX II Ethernet
Server Customer Diagnostics Kit.

WARNING: If your system is connected to a cluster, notify your cluster manager
before halting the system to load MDM.

You generally run MDM in three situations:

Before you install system software on a new system

When you receive an error message or experience a problem with your
system

When you want to test your system periodically to ensure that all
components are operating correctly

Running the MicroVAX Diagnostic Monitor (MDM}

3-1

The customer version of MDM is a subset of the service version of MDM.
The customer system test has two parts: a functional part that individually
tests each device installed in your system and an exerciser part that tests how
the devices work together. The customer tests cannot check every device in
the system. For example, customer tests check the controller but not the disk
drive, as testing the drive requires writing to the disk and possibly destroying
data.

Nor can the customer tests check each device as thoroughly as the

service diagnostic tests.

The customer tests check only the devices in the system, not the connectors
or lines between peripheral devices and the system.

If devices pass the

customer tests but you still experience problems, contact a DIGITAL service
representative for further testing.
Customers

requiring

complete

the MicroVAX Maintenance Kit.

diagnostic

testing

should

purchase

The kit includes the MicroVAX System

Maintenance Guide and the service diagnostic tests.

Only qualified service

personnel should use the service diagnostic tests.
Before you run the MDM software:
®*

Be sure you understand the instructions in MicroVAX II 630QY, 630QZ

Operation for using the device appropriate for your diagnostic media —

either the RX50 diskette drive or the TK50/TK70 tape drive.
*

Make sure the media (tape cartridge or RX50 diskette) is write-protected.

3.1 Starting MDM
The diagnostic tests run the same way whether or not software has been
installed.

NOTE: Before booting MDM on a system with software installed, warn all users
to log off and perform system shutdown, as described in your system software

manuals.
You must start the diagnostic tests differently, depending on the media used.

If you are booting MDM from an RX50 diskette, read Section 3.1.1.

If you

are installing MDM from a tape cartridge, read Section 3.1.2.

NOTE: Unless instructed to do so, do not change any settings or manipulate
devices while the tests are running. The diagnostic software interprets any change
of state as an error.

3—-2

MicroVAX 1l 630QY, 630QZ Troubleshooting

3.1.1 RXb0 Instructions
Because the system automatically boots first from an RX50 diskette, you can
run MDM software the same way, whether or not the system software has
been installed on the system. To run diagnostic software from RX50 diskettes,
do the following:
»

Press the fixed disk 0 Ready button on the system control panel to the
/

out position.

Insert diskette RX50A into one of the drives (be careful to align the orange
arrow on the diskette with the orange stripe on the drive) and close the
door.

Press the Restart button if the system is running, or turn on the system
if the system is off.

A countdown from 7 through 3 should appear on the console terminal
as the system performs self-tests. The countdown continues from 2 to 0
as the system loads the diagnostic software.
At this point, you may be prompted to remove diskette RX50A and insert
the next diskette. Remove diskette RX50A and insert diskette RX50B.

Within a few moments you should see the MDM introductory display, as
shown in Figure 3-1.

Running the MicroVAX Diagnostic Monitor (MOM)

3—3

Figure 3—1:

MDM Introductory Display

N
VAXELN

Vv2.2-11

MicrovAX Diagnostic Monitor - Version
CONFIDENTIAL

PROPERTY
DIGITAL

Use

Authorized Only

Digital
The

the

enter

EQUIPMENT

Pursuant

SOFTWARE

OF
CORPORATION

Valid Right-to-Use

License

1987

Equipment Corporation

current

Press

(c)

2.11

DIAGNOSTIC

date

RETURN

new

and time
key to

date

[DD-MMM-YYYY

is:

17-NOV-1987

00:00:01.64

continue

and time,

then

press

the

RETURN

key.

HH:MM]:

J
MLO-1531-87

NOTE: The version number on your display may differ from that shown in

Figure 3-1.
7.

Make sure the current date and time in the introductory display are
correct. If the current date and time are correct, press
to continue.

If incorrect, type the correct date and time, using the format shown in
For example, enter 25-DEC-1987 02:30 and press
to

Figure 3-1.
continue.

Within moments you receive a message that the system is preparing for

testing, as shown in Figure 3-2.

3—4

MicroVAX Il 630QY, 6300Z Troubleshooting

Figure 3—2:

Preparing for Testing Message

The system is preparing
This may take

for testing.

several minutes.

Please wait . . .

y
MLO-1532-87

Insert numbered diskettes in order, when prompted by the system, as
shown in Figure 3-3.

Running the MicroVAX Diagnostic Monitor (MDM)

3—5

Figure 3—3:

Diskette Removal Display

)

Please remove the diskette.

Insert the next diskette in the same drive
and press the RETURN key.

If you can not insert the next diskette,
type 1 and press the RETURN key.
>

J
MLO-1533-87

NOTE: If your system does not request all the diskettes containing diagnostic
software, your configuration does not need the additional diskettes for testing.
10. After a few minutes, you receive a message that the system is ready for
testing, as shown in Figure 3-4.

3—6

MicraVAX Il 630QY, 63007 Troubleshooting

Figure 3—4:

Ready for Testing Message

)

The system is

ready for testing

Press the RETURN key to continue.

v,
MLO-1534-87

When you press [Return|, the Main Menu appears. Section 3.2 describes options
on the Main Menu.

3.1.2 TK50/TK70 Instructions
NOTE: Before running MDM on your TK50 or TK70 tape drive, you may want
to reread the tape drive operating instructions found in MicroVAX II 630QY,
630QZ Operation.

If you are running diagnostic software from a tape cartridge, do the following:
1.

Make sure the write-protect switch on the tape cartridge is in the writeprotected position.

2.
3.

Remove the rear cover of your system, if it is not already removed.
Move the Halt Enable/Disable switch on the CPU panel to enable (dot
inside the circle).

Press the Restart button if the system is running, or turn on the system
if the system is off.

Running the MicroVAX Diagnostic Monitor (MDM)

3—7

When the green light on the tape drive glows steadily (orange and yellow

lights go out) insert the tape cartridge containing the MDM software into

the tape drive and lock it into place.
6.

Press the Load/Unload button to the load (in) position. While you are
inserting and loading the tape cartridge, the normal power-on countdown
from 7 through 3 should appear on the console terminal.

When the

countdown reaches 3, you should see the >>> prompt indicating console
mode.
7.

Use the command BOOT MUAO to tell your system to load the MDM
software from the tape cartridge.

Loading the software takes a few

minutes. An indicator light on the tape drive flashes while the loading

occurs. (If you are using a TK50 tape drive, a green light flashes. If you
are using a TK70 tape drive, a yellow light flashes.)

Within a few moments you should see the MDM introductory display, as
shown in Figure 3-5.

3-8

MicroVAX 1l 630QY, 6300Z Troubleshooting

Figure 3-5:

MDM Introductory Display

IFAVETAI
VOALUIN

Vied

MicroVAX Diagnostic Monitor - Version
CONFIDENTIAL

PROPERTY

DIGITAL

2.11

DIAGNOSTIC

EQUIPMENT

SOFTWARE

CORPORATION

Use Authorized Only Pursuant to a Valid Right-to-Use License
Copyright

(c)

1987

Digital Equipment Corporation
The current date and time iss

17-NQV-1987

00:00:01.64

Press the RETURN key to continue
or enter new date and time,
[DD-MMM-YYYY

——

then press

the RETURN key.

HH:MM]:

—

y,
MLO-1535-87

NOTE: The version number on your display may differ from that shown in
Figure 3-5.
Make sure the current date and time in the introductory display are

correct. If the current date and time are correct, press

to continue.

If incorrect, type the correct date and time, using the format shown in

Figure 3-5. For example, enter 25-DEC-1987 02:30 and press [Retun] to
continue.
10. Within moments you receive a message that the system is preparing for

testing, as shown in Figure 3-6.

Running the MicroVAX Diagnostic Monitor (MDM)

3-9

Figure 3—6:

Preparing for Testing Message

The

system

is preparing

This may take

for testing.

several minutes.

Please wait . .

y,
MLO-1536-87

11. After a few minutes, you receive a message that the system is ready for
testing, as shown in Figure 3-7.

3—10

MicroVAX Il 630QY, 630QZ Troubleshooting

Figure 3—7:

Ready for Testing Message

The system is ready for testing
Press the RETURN key to continue.

J
MLO-1537-87

When you press [Retun|, the Main Menu appears. Section 3.2 describes options
on the Main Menu.

3.2 Main Menu Options
NA.:
amis
heao
frrn
Adtiosma A
wn
i
3
i
3-8. Choose an option
Figure
in
as shown
options,
five
has
Menu
The. Main

by typing the number and pressing [Return],

Running the MicroVAX Diagnostic Monitor (MOM)

3-11

Figure 3—-8:

MDM Main Menu

p
MAIN MENU

Type

Test the

Display System Configuration

system

and Devices

Display the

System Utilities Menu

Display the

Service Menu

the

Exit Microvax Diagnostic Monitor
number;

then

press

the

RETURN

key.

y
MLO-1538-87

Option 4, Display the Service Menu, is available only if you have purchased
the MicroVAX Maintenance Kit.

The maintenance kit contains service
diagnostics and the MicroVAX System Maintenance Guide. Only qualified
service personnel should use the MicroVAX Maintenance Kit.

The next few sections describe the five options on the Main Menu.

3.2.1 Test the System
Test the System runs a quick, general test of the devices in the system
You can run the test at any time without
jeopardizing data.
and how they work together.

When you select Test the System, a screen explaining the testing procedures
appears, as shown in Figure 3-9.

3—-12

MicroVAX Il 630QY, 6300Z Troubleshooting

Figure 3-9:

System Test Screen

MAIN MENU
SYSTEM TEST

This is a test of the MicroVAX computer and its devices.
No additional preparation for this testing is required;
the MicroVAX is ready to be tested.
Testing occurs

in two parts:

the functional tests quickly

test each device sequentially; the exerciser test

(lasting

about 4 minutes)

tests how the devices work together.

To halt the test

any time

and return to the Main Menu,

type CTRL-C by holding down the CTRL key and pressing the C key.
Press the RETURN key to begin testing,
or type O and press the RETURN key to return to the Main Menu.

~——
MLO-1839-87

When you are ready to begin the test, press [Retum] The Begin Device Tests
screen appears, as shown in Figure 3-10.

Running the MicroVAX Diagnostic Monitor (MDM)

3-13

Figure 3—10:

Begin Device Tests Screen

A
This is a test of all system devices identified by

the

system.
If any of your system devices are not
listed
below, consult your system documentation for the action
to take.

Result

Device

... .

... ... .. ...

passed

MEMA . ...

CPUA

... .. ... ..

passed

RADXA

..
... ... .. .....

passed

TKXXA

...

... ... ...

passed

.. ... .. ... ... ..

passed

DELQAA
DH-CX0A

. ...
. ...........

J
MLO-1540-87

As each device passes the test, it is listed on the screen, as shown in Figure
3-10.

NOTE: Because of the internal similarity of some communications options, the
diagnostic test sees these options as the same device. A DHVII and DHQII
appear the same to the diagnostic test. A generic device name, DH-CXO0, is
listed for similar communications options. The last letter in each device name
differentiates among multiple devices of the same type. For example, DH-CX0A
indicates one communications option; DH-CXO0B a second, and so forth.
If a device fails the test, you receive a failure message, as shown in
Figure 3-11.

3-14

MicroVAX Il 630QY, 630QZ Troubleshooting

Device Failure Screen

Figure 3—11:

p
FAILURE DETECTED

A failure was detected while testing the

OPTION: DH-CXOA 8/16 line asynchronous multiplexer

No Field Replaceable Unit (FRU) was identified.
Consult your system documentation for the action
to

take.

Press the RETURN key to return to the previous menu.

MLO-1541-87

Each failure message identifies the device being tested when the failure
occurred and the field replaceable unit (FRU). Copy the failure message and
report it to your DIGITAL service representative.

If your system has serious problems, the following message may appear:
All devices disabled, no tests rum.

Report the message to your DIGITAL service representative.
When a failure message occurs, the testing stops.

When all devices pass the first part of the test, the exerciser test begins. This
test takes about four minutes and tests how the devices work together. At
the end of the test, you receive a success message, as shown in Figure 3-12.

Running the MicroVAX Diagnostic Monitor (MDM)

3-15

Figure 3—12:

System Test Passed Screen

SYSTEM TEST PASSED

All devices passed functional

the

At this point
or

Press

the

you may

perform more

additional

tests and

the

system passed

exerciser test.
exit

from the maintenance

specialized

information,

testing.

consult

system

you would

the Maintenance

Section

your System Technical Manual.
RETURN key to return to

the

previous menu.

J
MLO-1542-87

At the end of the system test, press [Retum]. The Main Menu appears. From
the Main Menu you can either exit MDM by choosing option 5, or you can

choose one of the other options.

3.2.2 Display System Configuration and Devices
The Display System Configuration and Devices screen identifies devices

recognized by the diagnostic software.

configuration and devices screen.

3—-16

MicroVAX Il 630QY, 6300Z Troubleshooting

Figure 3-13 shows a sample system

Figure 3—13:

Sample System Configuration and Devices Display

r
MAIN

SYSTEM

CONFIGURATION AND

CPUA

...
RA530

MO=NN

Cov—A

MS630-AA

and 2,

Q-bus

...

LIWI=N1

nv=ua

memory module:

...

RODXA-Q

TKXXA

MILTUV

...

banks

RODXAQA

DEVICES

MicroVAX/rtvax CPU

each bank has 4MB

SDI

REV MC=5

disk controller.
HW=3

TK50/TK70 CONTROLLER

TK-Q-REV MC=4

DH-CXOA ... Diagnostics for asynchronous multiplexers
CXA/CXB16 16 line No modem ctrl.
DELQAA

...

DELQA

EBthernet

controller

08-00-2B-06-0F-CD

Press the RETURN key to return to the previous menu.

Y,
MLO-1543-87

At least two lines of information are provided for each device. The first
line lists the name of the device and gives a brief description. The second
line indicates the revision level of the device. The revision level can refer
to hardware or microcode. For example, the KDA50 controller described in
Figure 3-13 is at revision 5 for microcode (MCF5) and revision 3 for hardware
(HW=3).

Besides the general information listed for each device, additional information
for specific devices is listed as foliows:

CPU — type of CPU, presence of a floating-point unit (FPU)

MEM — total amount of memory in megabytes and pages, number and
type of memory modules

RQDX3 — type, unit number, and description of each mass storage device
supported by the controller

DELQA/DEQNA — the Ethernet station address

Running the MicroVAX Diagnostic Monitor (MDM}

3-17

Communications devices — the type of device and whether it has modem
control

In addition to showing information about testable device options, MDM
displays message indicating the presence of nontestable systems devices. If a
device is physically present in the system but is not listed under the System
Configuration and Devices display, one of the following two messages can

indicate the reason.

Message 1:
No Dg KAA

...

Message number %x00000000

The “No Dg” (no diagnostic) “KAA” (KA630 CPUA) message appears in place
of the device name because a diagnostic was not loaded for the CPUA. This
can happen when the media is not installed properly or the diagnostic is not
present on the media.
MDM displays a “No Dg” message for each DIGITAL device present in the

system under these circumstances. For example, an unloaded TK70 diagnostic
results in the message, “No Dg TKA.” TKA indicates that the device is a TK70.

Message 2:
Invld Dev

...

Message number %x00000000

The “Invld Dev” (invalid device) message indicates that a device not
recognizable to MDM has been attached to the system. The message appears
under the following circumstances:
*

A device is configured to a nonstandard CSR address.

ADIGITAL device that has no diagnostic has been attached to the system.
This may occur if a device not supported on a MicroVAX II system has

been attached.
*

A non-DIGITAL device has been attached to the system.

Once all devices have been listed, you can return to the Main Menu by

pressing [Retur],

3.2.3 Display the Utilities Menu
When you choose Display the Utilities Menu, you see the System Utilities
Menu, as shown in Figure 3-14.

3—-18

MicroVAX Il 630QY, 630QZ Troubleshooting

Figure 3—14:

System Utilities Screen

MAIN

MENI

SYSTEM

UTILITIES

Utility

selections

- Customer

Type the number;
or type

are:

Disk Drive

Formatter.

then press the RETURN key,

and press the RETURN key to

return to the previous menu.

J/
MLO-1544-87

The only option available is the Customer Disk Drive Formatter. Choosing

this option enables you to format a fixed disk on your system or an RX33

diskette.

Choose the option by typing 1 and pressing [Retum].

Because

formatting destroys all data on the disk or diskette, a warning displays, as
shown in Figure 3-15.

Running the MicroVAX Diagnostic Monitor (MDM)

3—19

Figure 3—-15:

Formatting Utility Warning Screen

N
This DIGITAL Supported Software

product is warranted to
conform to the DIGITAL SOFTWARE PRODUCT DESCRIPTION (SPD)

applicable

for

this product

the

time

DIGITAL disclaims all other warranties,

including all warranties of
for a particular purpose.
manner

inconsistent

this utility will

Do you want to continue
Write protect

all

shipment.

express or implied,

merchantability and
Any use

with the

for which DIGITAL assumes no

WARNING,

SPD

of
an

drives not

in a

unsupported use,

liability.

destroy any user data on the

[YES=1,(N0O=0)]

fitness

this product

selected drive.

being formatted,

and press RETURN to

continue.

~—
MLO-1545-87

To begin the formatting operation, type 1 and press [Retum]. You are prompted
to write-protect all drives except the one you want to format.

If you are formatting an RX33 diskette, you must insert it into the diskette
drive.

Remove the write-protect tab, insert the diskette into the drive, and

lock the lever.
If you are formatting the fixed-disk drive, set the Write-Protect button for the
drive to write-enable (out).

NOTE: Because the MicroVAX II 630QY, 630QZ system has only one fixed-disk
drive, running the formatting utility destroys all data on the disk. Use this utility
only if you want to erase the contents of the disk and reinstall system software.

Press

when you are ready to continue.

A list of the drives and their unit numbers appears, as shown in Figure 3-16.

3-20

MicroVAX I 630QY, 630QZ Troubleshooting

Figure 3—-16:

List of Drives in System

Controller information for field service personnel:
MSCP Controller Model

Microcode Version #:

19
2

Your MicroVAX system contains the following drives:
Unit

Drive

Name

RD53 Fixed Disk

What unit do you want to format

(0-0) ?

—

J
MLO-1546-87

You are prompted to enter the unit number of the drive you want to format.

Type the number and press [Retum]. You are asked to verify the unit number.
If the unit number is incorrect, type 0, press

and re-enter the unit

number. If the unit number is correct, type 1 and press [Retun]. The formatting
operation begins. As the operation progresses, you receive status messages,
as shown in Figure 3-17.

Running the MicroVAX Diagnostic Monitor (MDM)

3-21

Figure 3—17:

Formatting Messages

Format

Beqgun.

Format

continuing

minutes

into

format

Format

is continuing

minutes

into

format

Format

is continuing --

minutes

into format

Format

minutes

into

continuing

format

)
MLO-1547-87

At the completion of the formatting operation, you receive a success message,

as shown in Figure 3-18.

3—-22

MicroVAX Il 630QY, 630QZ Troubleshooting

Figure 3-18:

Formatting Success Message

é
Format

is continuing

32 minutes

into

Format

is continuing

into format

Format

is continuing

34 minutes

The

drive

Wonld

youn

has been
like

minutes

into

format

formatted successfully.
format

another unit

[YES=1, (NO=0)1

,
MLO-1548-87

If you want to format another unit, type 1 and press |Return| to begin the
formatting process again. For example, if you want to format another RX33
diskette, remove the one just formatted, insert another, and repeat the process.

Otherwise, type 0 and press [Retun]. The Utilities Menu displays. To return
to the MDM Main Menu, type 0 and press [Return],

3.2.4 Display the Service Menu
This option is available only if you have purchased
Maintenance Kit, which includes the service diagnostics.

the MicroVAX
Only qualified

service personnel should run the service diagnostics.

3.2.5 Exit MDM
Choose this option when you are ready to leave MDM. Type 5 and press

[Retun]. You receive the exit message shown in Figure 3-19.

Running the MicroVAX Diagnostic Monitor (MDM)

3—23

Figure 3—-19:

Exit Display

(

MicroVAX

Diagnostic Monitor - Version

Exiting MicroVAX Maintenance
Exit

complete.

You

may

2.11

System.
now

load

your

system

software.

MLO-1549-87

Remove the RX50 diskette or tape cartridge, as explained in MicroVAX II

630QY, 630QZ Operation.

If you have run MDM on a new system, you are ready to install your system
software.

Follow the instructions in your system software manuals.

If you

have used the Disk Formatter Utility to format your fixed disk, you must
reinstall system software. Set the Write-Protect button to write-enable (out),

then install system software.

If you have run MDM on a system containing system software, you must
reboot your system software.
You can reboot your system software in two ways.
*

Press

or the Halt button on the control panel.

When the console

mode prompt >>> appears, use the command BOOT DUA1. DUAL1 is the

device name of the fixed disk containing your system software. After the
system software is loaded, set the Halt Enable/Disable switch to disable,
indicated by the dot outside the circle, to avoid inadvertently halting the
system by pressing the

3-24

key.

MicroVAX Il 630QY, 6300Z Troubleshooting

Set the Halt Enable/Disable switch to disable and press the Restart button
on the control panel. This causes your system to begin the power-on
sequence again and automatically load system software.

Running the MicroVAX Diagnostic Monitor (MDM}

3-25

Index
A

Fixed Disks (cont’d.)
operation problems, 2-2

Autobooting the system, 1-1

problems booting from, 1-4
Formatting a disk, 3-19

Formatting an RX33 diskette, 3-19

Countdown
displayed on LED, 1-1

displayed on screen, 1-1
during power-on, 1-1

L
LED display

on CPU panel, 1-1

Diskless systems
diagnosing problems on, 1-1

Main Menu

of MicroVAX Diagnostic Monitor

running MDM on, 3-1

using the MicroVAX II Ethernet
Server Customer Diagnostics

(MDM), 3-11
MicroVAX Diagnostic Monitor (MDM)

description, 3-1

Kit, 3-1

Main Menu, 3-11

Dispiay System Configuration and

medium containing, 3-1

Devices

running, 3-1

option on Main Menu, 3-16

starting, 3-2

Display the System Utilities Menu
option on Main Menu, 3-18

when to run, 3-1
MicroVAX Diagnostic Monitor

Ethernet Server User’s Guide

diskless systems use of, 3-1

Error messages

MicroVAX II Ethernet Server

Customer Diagnostics Kit

all devices disabled, 3-15

included with diskless systems,

Invld Dev, 3-18

3-1

No Dg, 3-18
Exit MicroVAX Diagnostic Monitor
(MDM)
option on Main Menu, 3-23

Power-on problems, 1-1

Preparing for Testing Screen, 3-5

Failure message example, 3-14

Fixed Disks

Rebooting the system

Index—1

Rebooting the system (cont’d.)

operation problems, 2-4

after running MDM, 3-24
RX50 diskette drives
operation problems, 2-2
problems booting from, 1-5
running MDM on, 3-3

problems booting from a tape
cartridge, 1-5
running MDM on, 3-7

TK70 tape drives
operation problems, 2-3

problems booting from a tape

cartridge, 1-5
running MDM on, 3-7

Self-test
during power-on, 1-1

Troubleshooting

during normal operation, 2-1

Starting the MicroVAX Diagnostic
Monitor (MDM), 3-2

from a TK50/70 tape cartridge,
3-7
from RX50 diskettes, 3-3
T

U
Utilities Menu
option on Main Menu, 3-18

Test the System
option on Main Menu, 3-12

TK50 tape drives

Index—2

Write-protecting disks
during formatting, 3-20

MicroVAXII630QY,630Q2
Technical information
Order Number EK-O05AB-1S—-002

digital equipment corporation

maynard, massachusetts

December 1986

September 1987

The information in this document is subject to change without notice and should not be construed as a
commitment by Digital Equipment Corporation.
Digital Equipment Corporation assumes no responsibility for any errors that may appear in this document.
The software, if any, described in this document is furnished under a license and may be used or copied only
in accordance with the terms of such license. No responsibility is assumed for the use or reliability of software
or equipment that is not supplied by Digital Equipment Corporation or its affiliated companies.
Copyright ©1986, 1987 by Digital Equipment Corporation.
All Rights Reserved.
Printed in U.S.A.

The READER'S COMMENTS form on the last page of this document requests the user’s critical evaluation to

assist in preparing future documentation.
The following are trademarks of Digital Equipment Corporation:

COMPACTape

MASSBUS

ThinWire

DEC

MicroVAX

ULTRIX

DECmate

PDP

UNIBUS

DECnet

P/0OS

VAX

DECUS

Professional

VAXcluster

DECwriter

Q-bus

VAXELN

DELNI

Rainbow

VMS

DEQNA

RSTS

DESTA

RSX

Work Processor

DIBOL

Eflmfluau TM

Bell is a trademark of Bell telephone companies.
POSTSCRIPT is a registered trademark of Adobe Systems Incorporated.
Proprinter is a trademark of International Business Machines Corporation.

TEKTRONIX is a registered trademark of Tektronix, Inc.
ML-5812
FCC NOTICE:

The equipment described in this manual generates, uses, and may emit radio frequency

energy. The equipment has been type tested and found to comply with the limits for a Class A computing
device pursuant to Subpart ] of Part 15 of FCC Rules, which are designed to provide reasonable protection
against such radio frequency interference when operated in a commercial environment.

Operation of this

equipment in a residential area may cause interference, in which case the user at his own expense may be

required to take measures to correct the interference.

Contents
Preface

vii

Chapter 1

Base System Specifications

1.1

Base System Operation

1.1.1

KA630 Firmware.

. ...........
... ... .......

1-1

. . .. .. ... ... i

1-1

1.1.2

CPU Panel Operation

. . .........
... ... .......

i-3

1.1.21

Switches . . ... ... ... ..

i-4

1.1.2.2

LEDDisplay . . . . ... ...

1-5

1.1.2.3

Console Terminal Connector

. .. ...............

1-6

Battery Backup Unit (BBU).

. . ..........
... ...

1-6

Base System Specifications . .. .............
.. .....

1-6

1.1.2.4

1.2
1.2.1

KA630 Processor Specifications

1.2.2

MS630 Memory Options.

. .. ...............

1-6

. . .. ..................

1-8

1.2.2.1

MS630-BA . . .. ...

1-9

1.2.2.2

MS630-BB . . ... ..

1-10

1.2.2.3

MS630-CA

1-11

Chapter 2
21
2.1.1

.. ..

Option Specifications

Mass Storage Options . . . ...... ... ... ...
Disk Drives and Controllers

...

2-2

. ... ................

2-2

2111

RQDX3 Controller . . . .. ...

2.1.1.2

RRD50 Disk Subsystem

2.1.2

. ..

2-2

. ....................

2-12

Tape Drives and Controllers . . ... ...............

2-15

2.1.2.1

TQK50 Controller

. .. ... ... .. ... . . . . . . .....

2-15

2.1.2.2

TQK70 Controller

. .. ... .. ... . . . . . . . ... .. ..

2-18

2123

TSVO5 Controller

. . ... ..... ...

... .......

2-21

Communications Options . . . . ....................

2-25

2.2

2.2.1

Asynchronous Serial Controllers . . . .. .............

2-25

2.2.1.1

DHV11 Asynchronous Multiplexer

. .............

2-25

2.2.1.2

DHQ11 Asynchronous Multiplexer

. .............

2-27

2.2.1.3

DZV11 Asynchronous Multiplexer . . . ... ... ......

2-30

2214

DZQ11 Asynchronous Multiplexer.

. . . ... ... .....

2-32

2215

DLVJ1 Asynchronous Interface . . .. .............

2-34

KMV1A Programmable Communications Controller

22.1.6

...

2-36

. . ....................

2-39

2.2.2.1

DMV11 Synchronous Controller . . ... ...........

2-39

2222

DPV11 Synchronous Interface

. ... .............

2-41

222

223
2.2.3.1
2.2.3.2

2.3

Synchronous Controllers.

Network Controllers

. . .. .. ...................

2-45

DELQA Ethernet Controller . . . .. ... ...........

2-45

DEQNA Ethernet Interface

2-46

...................

Real-Time Controllers . . ... ... ...

... ... ...

.....

2-49

2.3.1

DRQ3B Parallel Interface

... ...................

2-49

2.3.2

DRV11-] Parallel Interface

. . ...................

2-50

2.3.3

DRV11-WA Parallel Interface

2.34

IEQ11 Controller

.. .................

. .. ..... ... .. . .. . ...

2-52

.....

2-54

2.4

MRV11-D Programmable Read-Only Memory

. ... ......

2-57

2.5

Printers and Printer Interfaces . . . ... .... ... ... .....

2-59

25.1

Line Printers

2.5.2

Dot Matrix Printers . . . . . .......
... ... ... .....

2-71

2.5.3

Letter-Quality Printers . . . . ..........
... ... ... ...

2-81

2.5.4

Laser Printers . . . ... ....... ... ... ... ... ... ..

2-87

Chapter 3
3.1

Index

. ... ........
... . ... .. .. .. ...

2-59

System Expansion

Determining Expansion Capacity .. .................

3-1

Figures

1-1

CPUPanel . ... ...

1-4

3-1

BA23 Configuration Worksheet . . ... ...............

3-4

Tables

1-1
3-1

Console Program Boot Sequence .. .................
Power Requirements . . ... ......................

1-2
3-2

Preface
This book summarizes technical information about the MicroVAX II 630QY,

630QZ system. The book is organized as follows:
Chapter 1 describes the base system specifications, including the CPU
module and associated memory options.
Chapter 2 describes specifications for optional components available for

vii

Chapter

Base System Specifications
The MicroVAX 1I 630QY, 630QZ base system includes a KA630 CPU module
and one or two MS630 memory modules in a BA23 enclosure. The MicroVAX
II CPU normally resides in slot 1 of the backplane. It may not be installed
TY

rANMN/

in slots 4-8. Memory options may reside in slots 2 and 3.

1.1 Base System Operation

Base system operation includes the KA630 firmware and the controls on the
CPU panel.

1.1.1 KA630 Firmware

Two read-only memory (ROM) chips on the KA630 module contain firmware.
The firmware contains three major programs:
¢

A console program

A set of self-tests for the CPU and memory

A primary bootstrap program (VMB)

The console program receives control whenever the processor halts. For the
KA630 CPU, a halt means only that processor control has passed to the
console program, not that instruction execution stops. The standard VAX
console functionality is emulated by executing a program in ROM, rather
than by CPU microcode or a separate processor.

Control passes to the firmware under any of the following conditions:

The system is powered up

The Restart button is pressed

The Q22-bus BHALT signal is asserted (typically by pressing the
key or the Halt button when the Halt Enable/Disable switch is set to
enable)

A halt instruction is executed

Base System Specifications

1—1

A system error occurs

At power-up, the system enters one of three power-up modes
that are set
using the Power-Up Mode switch on the CPU panel. (The
modes and their

meanings are described later in the chapter.)

The console program then

determines the console device type and console language

The console program then runs the self-tests for the CPU
message

and memory. The

Performing normal system tests

is displayed on the terminal. As the tests progress, a countdo
wn displays on
the console terminal and on a LED display on the CPU panel.
MicroVAX
IT 630QY, 630QZ Operation describes the power-on sequence
and shows

examples of successful power-on operations.

MicroVAX II 630QY, 630QZ
Troubleshooting describes possible problems that can occur
during power-on.

If the self-tests are successful, the system does one of

two things, depending
on whether the Halt Enable /Disable switch on the CPU
panel is set to disable
or enable.
If the Halt Enable/Disable switch is set to disable, the

CPU tries to load and
start (bootstrap) an operating system. It locates a 64-Kbyt
e segment of system

memory and copies a primary bootstrap program,

called VMB, from the ROM

chip into the base address plus 512. The CPU then begins
executing VMB,
which attempts to bootstrap an operating system from
one of the devices in
Table 1-1 in the order shown.

Table 1-1:

Console Program Boot Sequence

Controller Type

Controller

Device Name

MSCP (Disk)

RQDX

DUmn!

MSCP (Tape)

TQK50/TQK70

MUmn

PROM

MRV11

PRAn

Ethernet adapter

DEQNA /DELQA

XQAn

Im = Mscp controller designator (A = first, B = second etc.)

n = unit number

When VMB determines that a controller is present,
it searches in order of
increasing unit number for a bootable unit with
a removable volume, then
proceeds to the next controller. If it finds none,
it will repeat the search for
a nonremovable volume.

1—2

MicroVAX 1l 630QY, 63007 Technical Information

If halt is enabled, the console program enters console I/O mode in response
to any halt condition, including system power-up. Console I/O mode allows
you to control the system by typing commands at the console terminal.

You can direct the system to boot a specific device when in console I/O
mode. Use the BOOT command, followed by the device name as listed in
Table 1-1. For example, to boot from the TK50 tape drive you would issue
the command: BOOT MUAO.

1.1.2 CPU Panel Operation
The CPU panel (accessible only after removing the back cover) contains the
following components, as shown in Figure 1-1.
*

Three switches

One LED display

One external connector for the console terminal serial line unit (SLU)

One battery backup unit (BBU) for the time-of-year clock and language
selection

Base System Specifications

1—3

Figure 1-1:

CPU Panel

BAUD

POWER-UP

SWITCH

RATE

MODE

HALT

ENABLE/DISABLE

SWITCH

yfiJ—L

)

CONSOLE

LED

TERMINAL

DISPLAY

CONNECTOR
MLO-1396-87

1.1.2.1 Switches
The three switches on the CPU panel (shown in Figure 1-1) operate as

follows:
Halt Enable/Disable Switch (2-position toggle)
Switch Position

Function
Halt
or

disable
restart,

ware

(factory
the

setting).

system

attempts

from one of the boot devices

power-up
load

at the

soft-

comple-

tion of self-tests.

Halt enable.

On power-up or restart, the system en-

ters

1/O

console

tests.

1—4

MicroVAX Il 630QY, 63007 Technical Information

mode

the

completion

self-

Power-Up Mode Switch (3-position rotary)
Switch Position

Mode

Run (factory setting).

If the console terminal sup-

ports Multinational Character Sets (MCS), the user is
prompted for language on power-up and restart only
if the battery backup has failed. Full start-up diagnostics are run.

Language inquiry.
ports
Multinational
user

prompted

If the console terminal
Character
Sets
(MCS),
for

language

every

supthe

power-

up and restart. Full start-up diagnostics are run.

Test.

ROM programs run wraparound serial line unit

(SLU) tests.

Baud Rate Switch (8-position rotary)
The baud rate switch has eight possible settings:
e

300

600

1200

2400

4800

9600

19200

38400

To change the baud rate, rotate the switch.
1.1.2.2 LED Display

The LED display on the CPU panel displays a countdown sequence as the
system runs its self-test diagnostics and bootstrap routine. The countdown
begins with F (15 in decimal) to 0. (The same display appears on the console
terminal beginning with 7.) See MicroVAX II 630QY, 630QZ Operation for
examples of successful power-on sequences, and MicroVAX II 630QY, 630QZ
Troubleshooting for examples of problems you may encounter during poweron.

Base System Specifications

1-5

1.1.2.3 Console Terminal Connector

The console cable is connected to the CPU panel as shown in Figure 1-1.
1.1.2.4 Battery Backup Unit (BBU)
A battery backup unit (BBU), located on the inside of the CPU panel, provides
power for maintaining the correct time-of-year and language selection when

power to the system is turned off.

Both the time-of-year and language

selection code are lost if the BBU fails.

The BBU provides power for up to

ten days if the system power is turned off.

1.2 Base System Specifications
1.2.1

KA630 Processor Specifications

The KA630 is a Q22-bus compatible VAX CPU, based on the MicroVAX chip
set.

Central Processor
Clock rate

20 megahertz

Data path width

32 bits

Number of data types

Hardware: 9
Software emulated: 7

Number of instructions

Hardware: 245

Software emulated: 59
General purpose registers

16 (32-bit wide)

Addressing modes

General register: 8
Program counter: 4

Index:

PDP-11 compatibility mode

Emulated in software

Time bases

Time-of-year clock: 1

Interval timer: 1 (10 milliseconds)
1/0O bus interface

One

Q22-bus

try map

1—6

MicroVAX Il 630QY, 63007 Technical Information

interface

with

8096

en-

Memory Management and Control
Page size

512 bytes

Virtual address space

4 gigabytes

Physical memory space

16 Mbytes

Number of memory modules

2 maximum

On-board memory

1 Mbyte

Performance

Instruction prefetch buffer size

8 bytes

Translation buffer

Direct mapped

Size

8 entry

Associativity

Fully associative

On-board memory cycle time

400 nanoseconds

1/0 bus buffer size
Input

32 bytes

Output

4 bytes

Maximum I/O bandwidth
DMA Read

2.6 Mbytes/second

DMA Write

3.3 Mbytes/second

Console Serial Line
Interface standards

EIA RS-423-A/CCITT V.10 X.26

EIA RS-232-C/CCITT V.28
Data format

1 start bit, 8 data bits, 0 parity bits, 1 stop bit

Baud rates

300, 600,

1200,

2400, 4800, $600,

19200,

38400

Ordering Information
KA630-AA

KA630-AA CPU module only

Base System Specifications

1—7

Ordering Information
CK-KA630-AF

KA630-A cabinet kit

Configuration Information
Form factor

Quad height

Power requirements

+5 Vdc, 6.2
+12 Vdc, 0.14

Bus loads

2.7 ac
1.0 dc

Operating System Support
MicroVMS

Version 4.1m and later

ULTRIX-32m

Version 1.1 and later

VAXELN

Version 2.0 and later

Diagnostic Support
MicroVAX Diagnostic Monitor

All versions

Self-tests

Yes

Related Documentation

EK-OTK50-TM

TK50 Tape Drive Subsystem Technical Manual

2.1.2.2 TQK70 Controller

The TQK70 controller module provides the interface between the TK70 tape
drive and the Q22-bus.
Functional Information
Controller protocol

TMSCP

Supported drive

TK70

Drives per controller

Drive interconnect

Direct

Controllers per system

1 maximum

Ordering Information

TQK70-AA

TQK?70 controller

TK70S5-AA

TK70 tape drive subsystem: includes TQK70
controller and TK70-AA tape drive

Performance

Data throughput rate

80 Kbytes/second

Read /Write data transfers

to 16-word burst mode DMA, truncated to 8-word burst mode if another device is requesting the bus.

Buffer size

64 Kbytes

Configuration Information
Form factor

Dual height

Power requirements

+5 Vde, 35 A
+12 Vde¢, 0.0 A

2-18

MicroVAX 1l 630QY, 63007 Technical Information

Configuration Information
Bus loads

4.3 ac
0.5 dc

Operating System Support
MicroVMS

Version 4.6 and later

ULTRIX-32

Version 2.2 and later

VAXELN

Not supported as of Version 2.4

Diagnostic Support

Self-tests

TK70 Tape Drive
The TK70 is a streaming tape drive subsystem that can store up to 296
Mbytes on a tape cartridge for backup data storage. The TK70 can read data
from tape cartridges recorded by a TK50 drive, but it cannot write data to
cartridges recorded by a TK50 drive.

Functional Information
Recording media

Magnetic tape

Tape dimensions

1.27 em (0.5 in) wide, 182.9 m (600 ft) long

Mode of operation

Streaming

Recording method

Serpentine

Recording density

10,000 bits/inch

Number of tracks

Storage capacity

296 Mbytes formatted

Option Specifications

2—19

Physical Specifications
Height

8.25 cm (3.25 in)

Width

14.60 cm (5.70 in)

Depth

21.44 cm (8.44 in)

Weight

2.27 kg (5.0 1b)

Ordering Information
TK70-AA

TK705-AA

TK70 tape drive

TK70 tape drive subsystem: includes TQK70
controller and TK70-AA tape drive

Performance
Tape start time

325 milliseconds maximum

Tape stop time

200 milliseconds maximum

Tape speed

100 in/second

Streaming data rate

125 Kbytes /second

Access time (from insertion of tape)
TK50 mode (read only)

35 minutes maximum

TK70 mode

60 minutes maximum

Configuration Information
Form factor

Standard 5.25-inch footprint

Power requirements

+5 Vdc, 1.3 A
+12 Vdc, 2.4 A

Bus loads

0.0 ac
0.0 dc

2—-20

MicroVAX Il 830QY, 6300 Technical Information

Operating System Support
MicroVMS

Version 4.6 and later

ULTRIX-32

Version 2.2 and later

VAXELN

Not supported as of Version 2.4

Diagnostic Support
MicroVAX Diagnostic Monitor

Revision 2.11 and later

Self-tests

Yes

Related Documentation

EK-IEUQ1-UG

2—-56

IEU11-A/IEQ11-A User’s Guide

MicroVAX Il 630QY, 630QZ Technical Information

2.4 MRV11-D Programmable Read-Only
Memory
The MRV11-D memory module contains sixteen 28-pin sockets that accept
static random-access memory (RAM) and a variety of user-supplied readonly memory (ROMs). By placing appropriate programmable ROMs into the
module, you can design your own boot sequence.
Ordering Information
MRV11-D

MRV11-D module

Configuration Information
Form factor

Dual height

Power requirements

+5 Vde, 1.6 A
+12 Vdc, 0.0 A

Bus loads

3.0 ac

0.5 dc

Operating System Support
VMS

Version 4.6A and later

ULTRIX-32

Version 2.2 and later

VAXELN

Not supported as of Version 2.4

Diagnostic Support
MicroVAX Diagnostic Monitor

Revision 2.11 and later

Self-tests

Related Documentation

EK-0LG02-UG

LGO02 600 LPM Text and Graphics Printer
User’s Guide

EK-0LG02-TM

LG02 600 LPM Text and Graphics Printer
Technical Manual

EK-0LG02-RM

LG02 600 LPM Text and Graphics Printer
Mini-Reference Manual

Option Specifications

2—69

2.5.2 Dot Matrix Printers
Four dot matrix printers are available for the MicroVAX II 630QY,QZ system:
LA75 Companion printer
LA100 Letterwriter

LA210 Letterprinter

LA75 Companion Printer

The LA75 is a high-speed, dot matrix printer designed for the office
environment.

Printing speed

Draft mode: 250 characters/second
Memo mode: 125 characters/second

Near-letter-quality mode: 42 characters/second

Letter-quality mode: 32 characters/second

Print technology

Bidirectional, dot matrix

Print density

Draft mode: 12 x 9 matrix
Memo mode: 24 x 9 matrix
Near-letter-quality mode

Letter-quality mode: 36 x 18 matrix
Bit-map graphics mode

Character spacing

10, 12, 16.5, 17.1 characters/inch (standardwidth characters)

5 6, 8.25, 8.5 characters/in.ch (doublewidth characters)

Line spacing

2,3,4,6,8, 12 lines/inch

Graphics

DIGITAL sixel protocol

Option Specifications

2—71

Performance
Character sets

Nine built-in character sets: U.S. ASCII, National

Replacement (NRC),

ISO

8-bit Sup-

plemental, DEC Supplemental, DEC Technical, VT100 Special Graphic, plus IBM Proprinter Line Drawing,

Chart Drawing,

and

Symbol Drawing sets.

Buffer capacity

2047-character input buffer

Communications
Baud rates

Character code

110 to 9600 bits/second

7- or 8-bit ASCII with odd, even, mark, space,
or no parity

Interface

EIA RS5-423
EIA R5-232-C parallel

Paper

Type

Fanfold.

Form width:

11.4 cm to 25.4 cm

(4.25 in to 10 in)

Single-sheet: 21.6 cm x 27.9 cm (8.5 in x 11
in)

Envelopes
Multipart forms: up to 4 parts, carbon or car-

bonless
Thickness

0.06 cm (0.002 to 0.012 in)

Power Requirements
Line voltage and frequency

120 Vac, at 50/60 Hz

240 Vac, at 50/60 Hz

Physical Characteristics
Height

2—72

12.1 cm (4.8 in)

MicroVAX 1l 630QY, 630QZ Technical Information

Physical Characteristics
Width

42.7 cm (16.8 in)

Depth

34.5 cm (13.6 in)

Weight

9.5 kg (21 1b)

Ordering Information
LA75-CA

EIA RS-423-A serial interface printer, U.S.,,
Canada (English, French)
13 other country-specific serial models available

LA75P-CA

Parallel model, U.S., Canada (English, French)
LWs

JPATY MUY WUV

10 ouner countua

oy
b P |

i NG

RS-|

"DPCL.I.IIL Pd[dllCl HIUUCLS avali-

able
H8571-A

Adapter for 25-pin male host printer port

H8571-B

Adapter for 9-pin male host printer port

Operating System Support
MicroVMS

Dependent on serial interface port
Dependent on serial interface port
Dependent on serial interface port

Diagnostic Support
MicroVAX Diagnostic Monitor

Revision 2.11 and later

Self-tests

Yes

Related Documentation

EK-LQP03-TM

LQP03 Printer Technical Manual

Option Specifications

2—85

2.5.4 Laser Printers
Three models of the LNO03 laser printer offer laser imaging and xerographic

printing in a desktop unit.
e

[NO03—basic text printer

LNO03 PLUS—text and bit-mapped graphics

LNO3R ScrirTPRINTER—Dbit-mapped graphics with support for PosTScripT,
a page description language that can integrate text and graphics

Performance

Print speed

Eight

pages/minute

ters/second

(about

letter-quality,

333

charac-

2500

charac-

ters/page)

Recommended duty cycle

3500 pages/month

Paper feed

Adjustable 250-sheet cassette (16 to 24 Ib pa-

per)
Paper output

250 sheets sequenced

Print orientation

Portrait:

lines/page,

120

charac-

lines/page,

150

charac-

ters /line

Landscape:

ters/line

Resolution

Image area

300 x 300 dots per inch

2400 dots/scan line x 3225 scan lines (ANSI
A)
2400 dots/scan line x 3400 scan lines (A4)

Paper sizes

Standard ANSI A: 21.6 x 27.9 cm (8.5 x 11
in)

European A4: 21 x 29.7 cm (8.3 x 11.7 in)

Character sets

Built-in:

ASCII, DEC Supplemental, DEC

Technical, and Line Drawing Set

Downline-loaded:

additional

avail-

able

Fonts

LNO03 and LN03 PLUS: 16 resident fonts

Option Specifications

2—87

Performance
LNO3R: 29 resident fonts

Other fonts available on ROM cartridges or

by downline loading them from a host
Graphics

Sixel protocol (LN03 PLUS and LNO3R)

TEKTRONIX

4010/4014

files

(LNO3

and

LNO3R)
ReGIS (LNO3R)
RAM

LNO3:

no on-board RAM; accepts two RAM

cartridges
LNO3

PLUS:

Mbyte on-board RAM;

ac-

cepts two RAM cartridges

LNO3R:

Mbytes

on-board

RAM;

ac-

cepts two RAM cartridges

ROM

LNO3:

no on-board ROM; accepts two pre-

coded ROM font cartridges

LNO3

PLUS:

on-board

ROM;

ac-

cepts two precoded ROM font cartridges

LNO3R:

POSTSCRIPT

Mbyte

interpreter;

on-board

ROM

for

accepts

two

pre-

coded ROM font cartridges

Communications

Interfaces

EIA RS5-232-C

Baud rates

1200, 2400, 3600, 4800, 7200, 9600, 19200

Parity

If enabled, even/mark or odd/space

Power Requirements

Voltage /Frequency

90-128 V at 50/60 Hz
190-256 V at 50 Hz

Power consumption

1 kVA max

Heat dissipation

3400 Btu/hour

2—-88

MicroVAX Il 630QY, 653007 Technical Information

Physical Characteristics
Height

38.1 cm (15 in) with exit tray

Width

53.4 cm (21 in)

Depth

59.7 cm (23.5 in) with tray

Weight

36.3 kg (80 Ib)

Ordering Information
LNO03-AA

U.S. model of LNO3

LNO3S-AA

U.S. model of LN03 PLUS

LNO3R-AA

U.S. model of LNO3R SCRIPTPRINTER
21

other

couniry-specific

modeis

avail-

able

Operating System Support
VMS

Dependent on serial interface port

ULTRIX-32

Dependent on serial interface port

VAXELN

Dependent on serial interface port

Diagnostic Support

MicroVAX Diagnostic Monitor

Dependent on serial interface port

Self-tests

Yes