Digital PDFs

EK-DSRVW-IN-001

January 1992

13 pages

Original

0.3MB

Document:	DECserver 700 Hardware Installation Card
Order Number:	EK-DSRVW-IN
Revision:	001
Pages:	13
Original Filename:

OCR Text

For: ROCH
Printed on: Mon, Jan 20, 1992 10:38:56
Document: DS700_CARD
Last saved on: Mon, Jan 20, 1992 10:29:43

EK-DSRVW-IN.001

DECserver 700
Hardware Installation Card

Rear View DECserver 700-16

Rear View DECserver 700-08
LKG-5809-91l

Check the Contents of the Box
If any part is damaged or missing, contact your
Digital Equipment Corporation sales representative.

Power cord

DECserver 700
Site Preparation
and Maintenence

Software license
Installation Card

Server feet
FTZ card (Austria/
Germany only,
DECserver 700-16
server only)

Blank ID labels
for cables

Rack-mount kit

Loopback connector
H4082-AA
(DECserver 700-16
server only)

LKG-5810-91l

Verify the Site
Verify that:
1. The devices (modems, printers, PCs, and terminals) and their cables are installed.
2. An Ethernet cable is installed.
3. A power socket is available within 1.8 meters
(6 feet) of the server position.
4. If you are to rack-mount the server, have available a number 1 or 2 crosspoint screwdriver
or a 3 mm (1/8 inch) flat blade screwdriver.

Place the Server – Desktop
1. Turn the server upside down.
2. Remove the backing from the feet.
3. Stick the feet to the server.

LKG-5812-91l

4. Allow for 15 centimeters (6 inches) of airspace
around the server air vents.

Place the Server – Racks
1. Install the nuts.

LKG-5813-91l

2. Install the brackets.

LKG-5814-91l

Place the Server – Racks (Cont.)
3. Install the server in the rack.

LKG-5815-91l

NOTE
This is the most common method of installing the
server in a rack. Refer to DECserver 700 Site
Preparation and Maintenance, Chapter 3, for other
methods.

Connect Device Cables to DECserver
700-08 Server
Caution
The V24/RS-232-C adapter (12-27591-01)
(not supplied) must be fitted between the server
and the extension cable if the modem/eliminator has Data Signal Rate Selector (DCE) on pin
23 (refer to modem manual).
1. If an adapter is needed:
a. Insert the adapter and tighten the
screws.
Screw

Screw

LKG-5816-91l

b. Insert the cable and tighten the screws.
Screw

Screw
LKG-5817-91l

2. If the adapter is not needed, insert the
25-pin D-connector and tighten the
screws.

LKG-5818-91l

Connect Device Cables to DECserver
700-16 Server

LKG-5819-91l

Connect the Ethernet Port
You may connect your server to standard,
10BaseT, or ThinWireTM Ethernet.
To connect to standard Ethernet:
1. Turn the Ethernet
select switch to the
right to select
standard Ethernet.

LKG-5820-91l

2. Unlock the
connector by
sliding the latch
to the right.

Ethernet
Unlock

LKG-5821-91l

3. Insert the cable.

LKG-5822-91l

4. Lock the connector by
sliding the latch to the left.

Lock

Ethernet

Lock

LKG-5823-91l

To connect to 10BaseT Ethernet:
1. Turn the Ethernet select
switch to the left
to select
10BaseT
Ethernet.

LKG-5824-91l

2. Insert the cable.

LKG-5811-91l

To connect to ThinWire Ethernet:
1. Turn the Ethernet select switch to the right to
select standard Ethernet.

LKG-5825-91l

To connect to ThinWire Ethernet (Cont.):
2. To connect to ThinWire Ethernet, you
must install a media access unit (MAU)
which is not supplied.
a. Insert the MAU.
b. Insert the ThinWire cable.

MAU

ThinWire
cable
LKG-5826-91l

Connect Power to Server

LKG-5827-91l

Verify Server Is Operating Correctly
When you plug in the power cable, the server
runs tests. After the tests are completed, the
server requests a down-line load of software.
The 7-segment display alternates between 3
and 4 until the software is loaded. Allow 3
minutes for the server to complete the procedure.
Compare the 7-segment display and the System OK LED status to the table on page 12.

7-Segment
display

System
OK LED

LKG-5828-91l

System
OK LED

7–Segment What to do
Display

Rotating
segments

No action. Server is
operating correctly.
Installation is complete.

FLASHING

Rotating
Segments

A nonessential function is not working.
Refer to DECserver
700 Site Preparation
and Maintenance for
further action.

OFF

Check that the power
cable is installed correctly and that power
is available. Refer to
DECserver 700 Site
Preparation
and
Maintenance if checks
show power is available.

OFF

FLASHING

Server has failed selftest. Refer to DECserver 700 Site Preparation and Maintenance for further action.

3 and 4
alternate

Check that the software is available on
the load host. If the
software is available,
refer to DECserver
700 Site Preparation
and Maintenance.