Digital PDFs

EK-BA44A-IN-J01

June 1994

116 pages

Original

1.8MB

Document:	BA400 Series Enclosures Storage Devices Installation Procedures
Order Number:	EK-BA44A-IN
Revision:	J01
Pages:	116
Original Filename:

OCR Text

BA400-Series Enclosures
Storage Devices
Installation Procedures
Order Number: EK–BA44A–IN. J01

Revision Information:

Digital Equipment Corporation
Maynard, Massachusetts

This manual supersedes
EK–BA44A–IN. H01

First Printing, June 1990
Revised, September 1990,
July 1991,
January 1992,
October 1992,
June 1994
July 1994
Digital Equipment Corporation makes no representations that the use of its products in the
manner described in this publication will not infringe on existing or future patent rights, nor do
the descriptions contained in this publication imply the granting of licenses to make, use, or sell
equipment or software in accordance with the description.
Possession, use, or copying of the software described in this publication is authorized only
pursuant to a valid written license from Digital or an authorized sublicensor.
© Digital Equipment Corporation 1994.
Printed in U.S.A.
The postpaid Reader’s Comments form at the end of this document requests your critical
evaluation to assist in preparing future documentation.
The following are trademarks of Digital Equipment Corporation: CompacTape, CX, DDCMP,
DEC, DECconnect, DECdirect, DECnet, DECscan, DECserver, DECUS, DECwindows, DELNI,
DEMPR, DESQA, DESTA, DSRVB, DSSI, IVAX, KDA, KLESI, KRQ50, MicroVAX, MSCP, Q–bus,
Q22–bus, RA, RQDX, RV20, SA, SDI, ThinWire, TK, TMSCP, TQK, TS05, TU, VAX, VAX 4000,
VAXcluster, VAX DOCUMENT, VAXELN, VAXlab, VAXserver, VMS, VT, and the DIGITAL logo.
Velcro is a registered trademark of Velcro USA, Inc.
All other trademarks and restricted trademarks are the property of their respective holders.
FCC NOTICE The equipment described in this manual generates, uses, and may emit radio
frequency energy. The equipment has been type tested and found to comply with the limits for
a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed
to provide reasonable protection against such radio frequency interference when operated
in a commercial environment. Operation of this equipment in a residential area may cause
interference, in which case the user at his own expense may be required to take measures to
correct the interference.
S2723

This document was prepared using VAX DOCUMENT Version 2.1.

Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 EF-, RF-, and RZ-Series Integrated Storage Elements
1.1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2
Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.1
ISE Installation in an Empty Slot . . . . . . . . . . . . . . . . . . . . .
1.3
Upgrading the ISE Storage Devices . . . . . . . . . . . . . . . . . . . . . . .
1.3.1
Removing ISEs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.2
Installing a Second Storage Device in a 3.5-inch ISE . . . . . . .
1.3.2.1
Remove the Top Outside Bracket . . . . . . . . . . . . . . . . . . .
1.3.2.2
Installing the New Storage Device . . . . . . . . . . . . . . . . . .
1.3.3
Installing Upgraded ISEs in the Mass Storage Cavity . . . . . .
1.3.4
Bus Node ID Plug Installation . . . . . . . . . . . . . . . . . . . . . . . .
1.4
Power-On Self-Test (POST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.1
EF-and RF-Series, and 3.5-inch RZ-Series POST . . . . . . . . . .
1.4.2
5.25-inch RZ-Series POST . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5
Setting the DSSI ISE Parameters . . . . . . . . . . . . . . . . . . . . . . . .
1.5.1
Accessing PARAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5.1.1
Using OpenVMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5.1.2
Using Console Commands . . . . . . . . . . . . . . . . . . . . . . . .
1.5.1.3
Using MDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5.2
Setting the ISE Allocation Class . . . . . . . . . . . . . . . . . . . . . .
1.5.3
Setting the MSCP Unit Number . . . . . . . . . . . . . . . . . . . . . .
1.5.4
Setting the ISE Node Name . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6
Testing the ISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6.1
DRVTST Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6.2
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7
Setting the SCSI ISE Parameters . . . . . . . . . . . . . . . . . . . . . . . .
1.7.1
Problem Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1–1
1–6
1–6
1–14
1–14
1–18
1–18
1–19
1–21
1–24
1–26
1–26
1–27
1–28
1–28
1–28
1–29
1–30
1–31
1–33
1–34
1–34
1–35
1–36
1–36
1–36

iii

2 TK-Series Tape Drive
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TQK-Series Controller Modules . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the CONFIG Utility for Module Configuration and
Naming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.1.1
Example 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.1.2
Example 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.2
Removing ISEs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.3
Installing the TQK-Series Controller Module and TK-Series
Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3
Power-On Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.1
TK70 Tape Drive POST . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.2
TK50 Tape Drive POST . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1
2.2
2.2.1

2–1
2–2
2–3
2–5
2–6
2–8
2–12
2–16
2–16
2–17

3 TLZ-Series Tape Drives
3.1
3.2
3.3
3.4
3.4.1
3.5
3.6
3.7
3.7.1
3.8

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TLZ04 Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TLZ04 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . .
Completing the TLZ04 Installation . . . . . . . . . . . . . . . . . . . . . . .
TLZ04 Power-On Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . .
TLZ07 Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TLZ07 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . .
Completing the TLZ07 Installation . . . . . . . . . . . . . . . . . . . . . . .
TLZ07 Power-On Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bus Node ID Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3–1
3–1
3–2
3–6
3–6
3–7
3–8
3–12
3–12
3–13

4 RRD-Series CD–ROM Drive
4.1
4.2
4.3
4.3.1
4.3.2

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Completing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RRD CD–ROM Power-On Self-Test . . . . . . . . . . . . . . . . . . . .
Bus Node ID Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4–1
4–1
4–10
4–11
4–12

5 RRD/TLZ07 Dual ISE Drives
5.1
5.2
5.3
5.3.1
5.3.2
5.3.3

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Completing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RRD CD-ROM Power-On Self-Test . . . . . . . . . . . . . . . . . . . . .
TLZ07 Power-On Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bus Node ID Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5–1
5–2
5–6
5–6
5–7
5–8

6 TF/TZ-Series Tape Drive
6.1
6.2
6.3
6.3.1
6.4

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TF/TZ-Series Tape Drive Installation . . . . . . . . . . . . . . . . . . . . . .
Completing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TF/TZ-Series Power-On Self-Test . . . . . . . . . . . . . . . . . . . . .
Setting the ISE Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6–1
6–2
6–7
6–7
6–8

A Related Documentation
Index
Figures
1–1
1–2
1–3
1–4
1–5
1–6
1–7
1–8
1–9
1–10
1–11
1–12
1–13
1–14
1–15

EF-Series ISE (Front and Rear View) . . . . . . . . . . . . . . . . . .
5.25-inch RF- and RZ-Series ISE (Front and Rear View) . . . .
3.5-inch RF/RZ-Series ISE (Rear View) . . . . . . . . . . . . . . . . .
Front Panel Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Switch Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BA440 Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blank Front Panel Assembly . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Plastic Skid Plate from the EF-Series ISE . . .
Installing the ISE in the Storage Cavity . . . . . . . . . . . . . . . .
Keylock Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the ISE to Be Upgraded or Replaced . . . . . . . . . . .
Removing the Top Outside Bracket from the ISE . . . . . . . . . .
Installing the Phillips Screws That Secure the Storage
Device to the Inside Brackets . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the ISE Upgrade in the Storage Cavity . . . . . . . . .
Inserting DSSI Bus Node ID Plugs . . . . . . . . . . . . . . . . . . . .

1–2
1–3
1–4
1–5
1–7
1–8
1–9
1–10
1–12
1–15
1–17
1–19
1–20
1–23
1–25

1–16
2–1
2–2
2–3
2–4
2–5
2–6
2–7
2–8
2–9
2–10
2–11
3–1
3–2
3–3
3–4
3–5
4–1
4–2
4–3
4–4
4–5
4–6
4–7
4–8
4–9
5–1
6–1
6–2
6–3
6–4

EF- and RF-Series ISE Front Panels . . . . . . . . . . . . . . . . . . .
TK70 Tape Drive Front Panel . . . . . . . . . . . . . . . . . . . . . . . .
TK-Series Tape Drive - Rear View . . . . . . . . . . . . . . . . . . . . .
TQK-Series Controller Module (TQK50) . . . . . . . . . . . . . . . . .
TQK-Series Controller Module (TQK70) . . . . . . . . . . . . . . . . .
Power Switch Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing an ISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the TQK-Series Controller Module and Routing
the Data Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attaching the Data Cable to the TK-Series Tape Drive . . . . .
Installing a TK-Series Tape Drive . . . . . . . . . . . . . . . . . . . . .
ISEs and Tape Drive Installed . . . . . . . . . . . . . . . . . . . . . . . .
TK50 Tape Drive Front Panel . . . . . . . . . . . . . . . . . . . . . . . .
TLZ04 Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening the Enclosure Doors . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the TLZ04 Drive . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening the Enclosure Doors . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the TLZ07 Drive . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening the Enclosure Doors . . . . . . . . . . . . . . . . . . . . . . . . .
Inserting the RRD CD–ROM drive . . . . . . . . . . . . . . . . . . . .
KZQSA IN Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Connector Cover . . . . . . . . . . . . . . . . . . . . . . .
KZQSA Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to KZQSA IN . . . . . . . . . . . . . . . . . . . . . . . . . . .
KZQSA Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
KZQSA Module Connector . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to KZQSA IN . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the RRD/TLZ07 Dual ISE . . . . . . . . . . . . . . . . . . .
TF85 Tape Drive Front Panel . . . . . . . . . . . . . . . . . . . . . . . .
Power Switch Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the TF/TZ-Series Drive . . . . . . . . . . . . . . . . . . . . .
TF/TZ-Series Drive Installed in Mass Storage Slot 0 . . . . . . .

1–26
2–1
2–2
2–4
2–5
2–9
2–11
2–12
2–13
2–14
2–15
2–18
3–2
3–3
3–5
3–9
3–11
4–3
4–5
4–6
4–7
4–7
4–8
4–9
4–9
4–10
5–5
6–1
6–3
6–5
6–6

Tables
1–1
2–1
6–1

DVTST Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unit Number Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-on Self-test Events . . . . . . . . . . . . . . . . . . . . . . . . . . .

1–36
2–7
6–7

vii

Preface
This manual describes add-on installation procedures for the various storage
devices available for BA400-series system enclosures.
Structure of This Manual
Chapter 1 describes the installation of EF-, RF-, and RZ-series integrated
storage elements.
Chapter 2 describes the installation of TK-series tape drive subsystems.
Chapter 3 describes the installation of the TLZ-series tape drives.
Chapter 4 describes the installation of the RRD43 CD-ROM drive.
Chapter 5 describes the installation of the RRD43/TLZ07 dual ISE drives.
Chapter 6 describes the installation of the TF/TZ–series tape drive.
Appendix A contains a list of related documentation.
Intended Audience
This document is intended for Digital Services personnel and self-maintenance
customers.

1
EF-, RF-, and RZ-Series Integrated Storage
Elements
1.1 General
Figure 1–1 shows the EF-series integrated storage elements (ISE). Figure 1–2
shows the RF- and RZ-series ISEs in the 5.25-inch configuration. Figure 1–3
shows the RF/RZ series ISEs in the 3.5-inch configuration. Note that the logic
module is located on the right side for the RZ-series, and on the left side for
the RF-series.
The three configurations vary as follows:
•

EF-series ISEs are solid state disks.

•

5.25-inch RF- and RZ-series ISEs contain only one hard disk storage device.

•

3.5-inch RF/RZ-series ISEs can contain two hard disk storage devices.

BA400-series ISEs contain hardware and a circuit module to allow the ISE to
be plugged into the enclosure backplane.

EF-, RF-, and RZ-Series Integrated Storage Elements 1–1

Figure 1–1 EF-Series ISE (Front and Rear View)
Bracket Slides

Bracket Slides
Front View

Rear View
MLO-009301

1–2 EF-, RF-, and RZ-Series Integrated Storage Elements

Figure 1–2 5.25-inch RF- and RZ-Series ISE (Front and Rear View)

Bracket Slides

Front View

Rear View
MLO-007239

EF-, RF-, and RZ-Series Integrated Storage Elements 1–3

Figure 1–3 3.5-inch RF/RZ-Series ISE (Rear View)

RF-Series
From back of drive:
the screw hole is
offset to the left
for DSSI.

Top Bracket

Tab

RZ-Series
From back of drive:
the screw hole is
offset to the right
for SCSI.

Flange

5-Pin
Power
Cable

Interface Card
Assembly
50-Pin
Signal Cable

50-Pin Signal Cable
4-Pin Power Cable
MLO-012804

1–4 EF-, RF-, and RZ-Series Integrated Storage Elements

Figure 1–4 shows the front panel assemblies that come with the ISEs.
Note
The ISE front panel for 5.25-inch RZ-series ISEs, unlike the front panel
for EF, RF, and 3.5-inch RZ-series ISEs, has no buttons or indicators,
only a plug for the bus node ID.

Figure 1–4 Front Panel Assemblies
Phillips Screw

EF/RF 5.25-inch

Phillips Screw

RF/RZ 3.5-inch

Phillips Screw

RZ 5.25-inch
MLO-007235

The term "Integrated Storage Element" (ISE) is used for any Digital Storage
Systems Interconnect (DSSI) or Small Computer System Interface (SCSI)
storage device. An ISE contains an on-board intelligent controller in addition
to the drive and the control electronics.
The DSSI interface supports up to seven ISEs. DSSI interfaces can be
embedded within a CPU module, such as the KA670 module. The DSSI
interface can also be separate modules, such as the KFQSA, which is interfaced
by a single cable to a DSSI connector in the host enclosure.
EF-series ISEs are DSSI-based solid state disk drives.

EF-, RF-, and RZ-Series Integrated Storage Elements 1–5

RF-series ISE storage devices are based on the Digital Storage Architecture
(DSA). The RF-series ISEs utilize the DSSI bus and interface. There are two
versions of the RF-series ISEs:
•

5.25-inch storage device

•

3.5-inch storage device
Note
Within a system enclosure it is possible to have up to seven disk
storage devices, provided there is no tape drive in the enclosure. There
can be three 3.5-inch dual storage devices and one 5.25-inch or one
3.5-inch single storage device.

RZ-series ISEs utilize the SCSI bus and interface. SCSI interfaces can be
embedded within a CPU module, such as the KN220 module. The SCSI
interface can also be separate modules, such as the HSD05, which is connected
by a single cable to the system backplane in the host enclosure.
Note
VAX 4000 systems do not support RZ-series ISEs unless an HSD05
option is installed.

For more detailed information about configuring EF-, RF-, and RZ-series ISEs
in a BA400-series enclosure, refer to the appropriate enclosure maintenance
manual listed in Appendix A.

1.2 Installation Procedure
To install an EF-, RF-, or RZ-series ISE in a BA400-series enclosure, perform
the following procedures.

1.2.1 ISE Installation in an Empty Slot
CAUTION
Static electricity can damage integrated circuits. Use the anti-static
wrist strap and antistatic pad found in the static-protective field service
kit (29-26246-00) when you work with the internal parts of a computer
system.

1–6 EF-, RF-, and RZ-Series Integrated Storage Elements

Handle the ISE with care. Dropping or bumping the ISE can damage
the disk surface. Carry or hold the ISE by the underside of the lower
bracket to avoid damaging the drive module.

1. After the system manager shuts down the operating system, set the lock
to the bottom position to open both the top and bottom enclosure doors
(Figure 1–10).
2. Set the power switch to off (0).
Figure 1–5 Power Switch Location

Power Switch

MLO-006627

EF-, RF-, and RZ-Series Integrated Storage Elements 1–7

3. Always install ISEs working from right to left (Figure 1–6).
Figure 1–6 BA440 Enclosure
Slot 3

Slot 2

Slot 1

Slot 0

MLO-006528

NOTE
The first (slot 0) mass storage cavity in the mass storage area is wider
than the rest to accommodate a larger device, such as a tape drive. A
small filler panel (70-27414-01) is used to fill the gap when an EF-,
RF-, or RZ-series ISE is installed in this first cavity.

1–8 EF-, RF-, and RZ-Series Integrated Storage Elements

4. Loosen the captive Phillips screw that secures the blank ISE front panel
assembly (Figure 1–7), and remove the panel.
Figure 1–7 Blank Front Panel Assembly

Phillips Screw

MLO-007236

EF-, RF-, and RZ-Series Integrated Storage Elements 1–9

5. For 5.25-inch EF-series ISEs, remove the plastic skid plate from the right
side (remove the four screws) of the device (Figure 1–8). Discard the skid
plate.
Figure 1–8 Removing the Plastic Skid Plate from the EF-Series ISE

Skid Plate

Screws

MLO-009302

1–10 EF-, RF-, and RZ-Series Integrated Storage Elements

6. For the EF-series ISEs, with the side that had the skid plate attached to it
facing to the right, slide the ISE along the guide rails into the mass storage
cavity (Figure 1–9A).
For 5.25-inch RF and RZ-series ISEs, and 3.5-inch RZ-series ISEs: with
the ISE controller module facing to the right, slide the ISE along the guide
rails into the mass storage cavity (Figure 1–9A).
For 3.5-inch RF-series ISEs, with the controller module facing to the
left, slide the ISE along the guide rails into the mass storage cavity
(Figure 1–9A).

EF-, RF-, and RZ-Series Integrated Storage Elements 1–11

Figure 1–9 Installing the ISE in the Storage Cavity

Captive Screws

Remote Front
Panel Cable

Guide
Tabs

Phillips Screw

Finger Cutouts

Remote Front
Panel Cable

Velcro
Fastener

RF/RZ 5.25-inch

RF/RZ 3.5-inch

RZ 5.25-inch
MLO-007244

1–12 EF-, RF-, and RZ-Series Integrated Storage Elements

7. Refer to Figure 1–9A and install the ISE.
Using the tabs in front of upper and lower finger cutouts, firmly push
the ISE brackets until the interface card at the rear of the storage
device plugs into its backplane connector. The guide tabs on the upper
and lower bracket should line up with the cutouts in the chassis.
8. Tighten the two captive screws at the top and bottom of the bracket.
CAUTION
It is normal for there to be a small gap between the ISE mounting
bracket tabs and the enclosure frame. Tighten the captive screws only
until they are securely fastened (9 inch-pounds). Do not try to force the
tabs to fit flush against the frame.

9. Plug the remote front panel cable(s) into the connector(s) inside the ISE
front panel.
For 5.25-inch ISEs see Figure 1–9B.
For 3.5-inch ISEs see Figure 1–9C.
For the 5.25-inch ISEs only, use Velcro on the cable and on the inside of the
ISE front panel to secure the remote front panel cable. The 3.5-inch ISEs
have a different connector scheme that does not require Velcro.
Note
The front panel for the 3.5-inch ISE has two remote front panel cables
when there are two storage devices in the ISE. If the ISE contains only
one storage device there is only one remote front panel cable.

10. Attach the ISE front panel to the enclosure by first fitting the panel’s lower
tabs into position.
Fit the panel into position and secure the panel with its single captive
Phillips screw (Figure 1–9D).

EF-, RF-, and RZ-Series Integrated Storage Elements 1–13

1.3 Upgrading the ISE Storage Devices
The system’s storage capacity can be increased by:
•

Replacing an ISE with one that has a larger storage capacity

•

Installing a second storage device on a 3.5-inch ISE

The following sections describe how to upgrade the ISE storage devices.

1.3.1 Removing ISEs
To upgrade a system, it may be necessary to remove an ISE. To remove an ISE,
use the following procedures.
CAUTION
Static electricity can damage integrated circuits. Always use the
antistatic wrist strap and antistatic pad found in the static-protective
field service kit (29-26246-00) when working with the internal parts of
a computer system.
Handle ISEs with care. Dropping or bumping the ISE can damage the
disk surface. Carry or hold the ISE by the underside of the lower metal
bracket to avoid damage to the drive module.

1–14 EF-, RF-, and RZ-Series Integrated Storage Elements

1. After the system manager shuts down the operating system, set the lock
to the bottom position to open both the top and bottom enclosure doors
(Figure 1–10).
2. Set the Power switch to off (0).
Figure 1–10 Keylock Positions

Key Lock

Top Key Position

MLO-004034

Power
Switch

MLO-004035

Bottom Key Position
MLO-012859

EF-, RF-, and RZ-Series Integrated Storage Elements 1–15

3. Loosen the captive Phillips screw that secures the ISE front panel and
remove the panel (Figure 1–11/Step 1).
4. Separate the ISE front panel from the enclosure, taking care not to strain
the remote front panel cable(s) connected to the ISE front panel.
5. Unplug the remote front panel cable(s) from the connector(s) inside the ISE
front panel (Figure 1–11/Step 2).
Note
If the ISE is a 3.5-inch device, there can be two cables.

6. Loosen the upper and lower captive screws that hold the ISE in place
(Figure 1–11/Step 3).
7. Using the upper and lower finger cutouts on the ISE brackets, carefully
pull the ISE out of its backplane connector and slide the drive out of the
enclosure. Support the weight of the ISE at the underside of the lower
bracket as the ISE clears the enclosure (Figure 1–11/Step 4).
CAUTION
Do not touch the drive module. The drive module contains sensitive
electronic circuitry.

If you are not upgrading a 3.5-inch ISE with a second storage device, go to
Section 1.3.3.

1–16 EF-, RF-, and RZ-Series Integrated Storage Elements

Figure 1–11 Removing the ISE to Be Upgraded or Replaced

1 Phillips Screw
2
Remote Front
Panel Cable

Velcro

RZ 5.25-inch

RF/RZ 5.25-inch

RF/RZ 3.5-inch

3 Captive Screws
(loosen)

Remote Front
Panel Cable

Guide
Tabs

4 Finger Cutouts
(pull)
MLO-007247

EF-, RF-, and RZ-Series Integrated Storage Elements 1–17

1.3.2 Installing a Second Storage Device in a 3.5-inch ISE
The upgrade kit for the 3.5-inch ISE contains the following:
•

Storage device

•

Mounting hardware—four Phillips screws

•

Remote front panel cable

•

BA400-Series Enclosures Storage Devices Installation Procedures

The following sections describe how to install a second storage device in a
3.5-inch ISE.
1.3.2.1 Remove the Top Outside Bracket
Complete the following steps to remove the top outside bracket from the ISE.
Note
To ensure that each bus node ID plug remains with the original storage
device, upgrade one 3.5-inch ISE at a time.
Note the orientation of the mounting bracket before you take it apart.
DSSI devices have a different orientation than SCSI devices (refer to
Figure 1–3).

1. Unplug the remote front panel cable from the storage device. Set it aside;
it will be reinstalled later in the procedure.
2. Remove the two mounting screws on the top outside bracket and put them
aside.
3. Push up the plastic flange of the interface card assembly, and lift the top
outside bracket’s rear slot over the plastic flange.
4. Unplug the power cable and the 50-pin signal cable from their connectors
on the ISE controller module (Figure 1–12).

1–18 EF-, RF-, and RZ-Series Integrated Storage Elements

Figure 1–12 Removing the Top Outside Bracket from the ISE

Top Bracket

Tab

Flange
Power Cable

Interface Card
Assembly

50-Pin Signal Cable

MLO-007241

5. Gently turn the storage device upside down so that it rests on the top
inside bracket.
6. After removing both mounting screws on the bottom outside bracket, set
the bracket and the screws aside.
1.3.2.2 Installing the New Storage Device
Complete the following procedures to install a new storage device:
1. Secure the bottom inside bracket and the top inside bracket to the storage
device using the screws provided in the upgrade kit (Figure 1–13).
2. Reinstall the bottom outside bracket and then the top outside bracket.
3. Connect the power and signal (50-pin) cables to both drives.
4. Connect the remote front panel cable(s) to the controller module(s) on the
storage device(s), the original one plus the one provided with the upgrade
kit.

EF-, RF-, and RZ-Series Integrated Storage Elements 1–19

Figure 1–13 Installing the Phillips Screws That Secure the Storage Device to
the Inside Brackets
Phillips
Screws

Bottom of ISE

Bottom Inside
Bracket

Controller
Modules

MLO-007246

Installation Notes
When you install the new drive, be sure to complete the following:
1. Align the new storage device in the same orientation as the original device.
2. When reinstalling the top outside bracket, lift the bracket’s rear slot over
the flange of the plastic interface card assembly, and then over the tab at
the back of the bottom outside bracket. Both the tab and the flange must
be inside the rear slot of the top outside bracket.
3. Make sure that the grounding foil is in place under the front mounting
screw on the bottom outside bracket.

1–20 EF-, RF-, and RZ-Series Integrated Storage Elements

1.3.3 Installing Upgraded ISEs in the Mass Storage Cavity
To install a 5.25-inch ISE upgrade or an upgraded 3.5-inch ISE, complete the
following procedure:
1. For the EF-series ISEs, with the side that had the skid plate attached to it
facing to the right, slide the ISE along the guide rails into the mass storage
cavity (Figure 1–14A).
For 5.25-inch RF and RZ-series ISEs, and 3.5-inch RZ-series ISEs: with
the ISE controller module facing to the right, slide the ISE along the guide
rails into the mass storage cavity (Figure 1–14A).
For the 3.5-inch RF-series ISEs: with the controller module facing to
the left, slide the ISE along the guide rails into the mass storage cavity
(Figure 1–14A).
2. Refer to Figure 1–14A and install the ISE.
Using the tabs in front of upper and lower finger cutouts, firmly push
the ISE brackets until the interface card at the rear of the storage
device plugs into its backplane connector. The guide tabs on the upper
and lower bracket should line up with the cutouts in the chassis.
3. Tighten the two captive screws at the top and bottom of the bracket.
CAUTION
It is normal for there to be a small gap between the ISE mounting
bracket tabs and the enclosure frame. Tighten the captive screws only
until they are securely fastened (9 inch pounds). Do not try to force the
tabs to fit flush against the frame.

EF-, RF-, and RZ-Series Integrated Storage Elements 1–21

4. Plug the remote front panel cable(s) into the connector(s) inside the ISE
front panel.
For 5.25-inch ISEs see Figure 1–14B.
For 3.5-inch ISEs see Figure 1–14C.
For the 5.25-inch ISEs only: use Velcro on the cable and on the inside of
the ISE front panel to secure the remote front panel cable. The 3.5-inch
ISEs have a different connector scheme that does not require Velcro.
Note
The front panel for the 3.5-inch ISE has two remote front panel cables
when there are two storage devices in the ISE. If the ISE contains only
one storage device there is only one remote front panel cable.

5. Attach the ISE front panel to the enclosure by first fitting the panel’s lower
tabs into position. Fit the panel into position and secure the panel with its
single captive Phillips screw (Figure 1–14D).

1–22 EF-, RF-, and RZ-Series Integrated Storage Elements

Figure 1–14 Installing the ISE Upgrade in the Storage Cavity

Captive Screws

Remote Front
Panel Cable

Guide
Tabs

Phillips Screw

Finger Cutouts

Remote Front
Panel Cable

Velcro
Fastener

RF/RZ 5.25-inch

RF/RZ 3.5-inch

RZ 5.25-inch
MLO-007244

EF-, RF-, and RZ-Series Integrated Storage Elements 1–23

1.3.4 Bus Node ID Plug Installation
The 3.5-inch configuration has two node ID plugs for two storage devices.
When a 3.5-inch configuration contains only one storage device, the node ID
plug for the empty cavity is unnumbered.
To insert a bus node ID plug (12-28766-19) align the two center prongs with
the two center slots of the receptacle on the ISE front panel (Figure 1–15).
Push the plug firmly into the receptacle. To remove a bus node ID plug, grasp
it firmly and pull it straight out.
Use the following rules for numbering IDs for EF-, RF-, and RZ-series ISEs:
•

For each DSSI bus or SCSI bus, do not duplicate bus node numbers
for storage elements. You can have only one storage element on bus 0
identified as node 0, one storage element as node 1, and so on.

•

By convention, the ISEs are numbered in increasing order from right to
left, starting with 0.
NOTE
The node ID address assigned by the plug is read only during the
power-up sequence. If you change the bus node ID plug while the
system is operating, you must turn off the system and then turn it back
on for the new ID addresses to take effect.

Caution
On an EF-series ISE with a data retention unit, you must wait for the
data retention cycle to complete, before turning the power back on.

1–24 EF-, RF-, and RZ-Series Integrated Storage Elements

Figure 1–15 Inserting DSSI Bus Node ID Plugs

Bus Node
ID Plugs

Bus Node
ID Plug
RF 5.25-inch

RF/RZ 3.5-inch

Bus Node
ID Plug
RZ 5.25-inch
MLO-007237

EF-, RF-, and RZ-Series Integrated Storage Elements 1–25

1.4 Power-On Self-Test (POST)
Once the system is turned on, the EF-series, RF-series and RZ-series ISEs go
through a power-on self-test (POST).

1.4.1 EF-and RF-Series, and 3.5-inch RZ-Series POST
POST is executed whenever power is applied. For EF- and RF-series, and
3.5-inch RZ-series ISEs when POST is executed successfully, the green Ready
and red Fault LEDs (Figure 1–16) go through the following sequence:
1. Both LEDs are lit.
2. Both LEDs turn off.
3. The green Ready LED flashes.
4. The green Ready LED remains lit steadily, the red Fault LED remains off.
Once this sequence occurs, the ISE is ready to be used. If POST fails, the red
Fault LED remains lit.
Figure 1–16 EF- and RF-Series ISE Front Panels

Fault
Indicator

Bus Node
ID Plugs

Bus Node
ID Plug

Run/Ready Button
Write-Protect Button

Run/Ready
Indicator

Fault
Indicator

Fault Indicator
MLO-007238

1–26 EF-, RF-, and RZ-Series Integrated Storage Elements

On the EF-series, POST performs the following:
•

Tests the control module.

•

Tests the memory modules.

•

Checks the configuration of the hard disk.

On the RF-series when POST begins, the first action it takes is to start the
spindle spin-up sequence. Other tests are performed while the spindle is
spinning up.
POST detects the following types of error conditions:
•

Controller errors—Caused by the hardware associated with the controller
function of the drive module. These errors are fatal to the operation of the
ISE since the controller cannot establish a logical connection to the host.
Controller errors cause the red Fault LED to light.

•

Device errors—Caused by the hardware associated with the device control
function of the drive module. These errors are not fatal since the ISE
can establish a logical connection and report the error to the host. Device
errors cause both LEDs to turn off for about 1 second, then the red Fault
LED lights.

If the ISE passes POST, continue to Section 1.5.

1.4.2 5.25-inch RZ-Series POST
POST for a 5.25-inch RZ-series ISE is executed during power-up or from a
host-initiated command. The execution time for the test should be less than
two seconds. If the unit passes POST, it waits for a software command such as
SHOW DEVICES. If POST fails, the device will not come on line and will not
be listed in the device listing when the SHOW DEVICES command is issued.

EF-, RF-, and RZ-Series Integrated Storage Elements 1–27

1.5 Setting the DSSI ISE Parameters
Once installed and powered up, the DSSI ISE parameters must be set. This is
done through the use of the local program PARAMS. The following procedures
should be used when performing an ISE installation. If further information
on the use of PARAMS is desired, refer to the appropriate integrated storage
element user’s guide (see Appendix A) for a complete description of the
PARAMS utility.

1.5.1 Accessing PARAMS
PARAMS can be accessed in one of three ways, depending on the system you
are using.
•

Through OpenVMS, using the SET HOST command

•

From the console, using the SET HOST command

•

Through MDM, using the Device Resident Programs menu

1.5.1.1 Using OpenVMS
To access PARAMS on a system running OpenVMS Version 5.3 or higher, the
command is:
$ SET HOST/DUP/SERVER=MSCP$DUP/TASK=PARAMS nodename
where "nodename" is the node name of the ISE.
NOTE
To find the node name, enter SHOW DEVICES or SHOW CLUSTER at
the $ prompt.

To produce a file in your directory of what appears on the screen, append the
qualifier/log=filename.ext (where filename.ext is what you want to name the
file) to the above command.
Once you are in PARAMS, control is turned over to the utility. All interaction
is through the use of commands and responses.
To exit PARAMS, enter EXIT at the PARAMS> prompt, or press one of the
following key combinations: CTRL/C , CTRL/Y , or CTRL/Z .

1–28 EF-, RF-, and RZ-Series Integrated Storage Elements

1.5.1.2 Using Console Commands
From console mode you can access the Diagnostic and Utility Program (DUP)
to examine and set parameters. The command syntax depends upon whether
your system uses an embedded adapter such as the KA670 module, or a Q–bus
adapter (the KFQSA module).
Embedded Adapters
To access PARAMS from a system with an embedded adapter, enter:
>>> SET HOST/DUP/DSSI/BUS:<BUS_NUMBER>
<NODE_NUMBER> PARAMS
where
<BUS_NUMBER> is the DSSI bus number (0 or 1) and <NODE_NUMBER> is
the bus node ID (0–7) for the device on the bus.
NOTE
To find the DSSI bus number and node number, enter SHOW DSSI at
the console ( >>> ) prompt.
KFQSA Storage Adapter
To access PARAMS from a system with a Q–bus adapter, enter:
>>> SET HOST/DUP/UQSSP/DISK <controller_number> PARAMS
where
<controller_number> is the controller number (provided by the SHOW UQSSP
display) for the device on the bus.
After you have completed setting and examining DSSI device parameters, enter
the WRITE command at the PARAMS> prompt to save the device parameters
you have changed using the SET command. The changes are recorded to
nonvolatile memory.
If you have changed the allocation class or node name of a device, the DUP
driver utility will ask you to initialize the controller. Answer Yes (Y) to allow
the changes to be recorded and to exit the DUP driver utility.
If you have not changed the allocation class or node name, enter the EXIT
command at the PARAMS> prompt to exit the DUP driver utility for the
specified device.

EF-, RF-, and RZ-Series Integrated Storage Elements 1–29

1.5.1.3 Using MDM
If neither OpenVMS nor console commands are available on your system, you
can access PARAMS through MDM using the following procedure:
1. Boot MDM.
2. Enter the date and time.
3. Select the menus in the following order:
•

Service menu

•

Device menu

•

KFQSAA-KFQSA subsystem menu

•

Device Utilities menu

•

Device Resident Programs menu

When you select the Device Resident Programs menu, the following is
displayed:
RUNNING A UTILITY SERVICE TEST
To halt the test at any time and return to the previous menu,
type CTRL/C .
KFQSAA started.
KFQSAA pass 1 test number 3 started.
Copyright 1988 Digital Equipment Corporation
Completed.
EXIT
DRVEXR
HISTRY
ERASE
DIRECT
DKUTIL
VERIFY
Please choose a local program or press

Return

DRVTST
PARAMS
PRFMON
to continue.

4. Enter PARAMS and press Return .
5. Once you are in PARAMS, control is turned over to the utility. All
interaction is through the use of commands and responses.
6. To exit PARAMS, enter EXIT at the PARAMS> prompt, or press one of the
following: CTRL/C , CTRL/Y , or CTRL/Z .
7. To exit MDM, press the Break key.

1–30 EF-, RF-, and RZ-Series Integrated Storage Elements

1.5.2 Setting the ISE Allocation Class
All DSSI ISEs are shipped with the allocation class set to 0. To determine
what the allocation class should be set to, access a different ISE on the system
and set the one you are installing to the same allocation class.
In multihost systems, you must assign the same allocation class to all host
systems and all connected ISEs. This allocation class must be different from
that of other systems or other hierarchical storage controllers (HSCs) in a
cluster.
Use the following procedure to set the allocation class:
1. Determine what the allocation class should be set to by reading it from
another ISE that is already working on the system. Use one of the
procedures outlined in Section 1.5.1 to access PARAMS on the ISE from
which you want to read this information.
2. At the PARAMS> prompt, enter SHOW ALLCLASS. The system displays
the following:
Parameter
--------ALLCLASS

Current
----------1

Default
----------0

Type
-----Byte

Radix
------Dec B

PARAMS>
3. Make a note of the allocation class. In the example above, the allocation
class has been set to 1. Exit PARAMS and return to the root prompt
(OpenVMS, console, or MDM).
4. Access PARAMS on the newly installed ISE, using one of the procedures
outlined in Section 1.5.1.

EF-, RF-, and RZ-Series Integrated Storage Elements 1–31

5. Enter SHOW ALLCLASS. The system responds with:
Parameter
--------ALLCLASS

Current
----------0

Default
----------0

Type
-----Byte

Radix
------Dec B

PARAMS>
6. Enter SET ALLCLASS 1 (for our example). You want to set the ISE to the
same allocation class as all the other ISEs on the DSSI bus.
7. Enter SHOW ALLCLASS to check the new allocation class.
The system responds with:
Parameter
--------ALLCLASS

Current
----------1

Default
----------0

Type
-----Byte

Radix
------Dec B

PARAMS>
8. Enter WRITE. The system responds with:
Changes require controller initialization, ok? [Y/ (N)]
9. Enter Y to save the new allocation class value.

1–32 EF-, RF-, and RZ-Series Integrated Storage Elements

1.5.3 Setting the MSCP Unit Number
The ISE is set at the factory to read the DSSI node ID as the MSCP unit
number. Unit numbers for all DSSI devices connected to a system’s associated
DSSI buses must be unique. When more than one bus is being used, and
your system is using a nonzero allocation class, you need to assign new unit
numbers for devices on all but one of the DSSI buses.
When assigning a different unit number, you must also set the FORCEUNI
parameter to 0. This allows the unit number you have set to be used. The
factory setting for FORCEUNI is 1, forcing the DSSI node ID to be used as the
MSCP unit number.
The following example shows how to change the MSCP unit number:
PARAMS> sh unitnum
Parameter Current
Default
Type
--------- ------------ ------------- --------UNITNUM
5
0
Word

Radix
----Dec

PARAMS> sh unitnum
Parameter Current
Default
Type
--------- ------------ ------------- --------UNITNUM
21
0
Word

Radix
----Dec

PARAMS> sh forceuni
Parameter Current
Default
Type
--------- ------------ ------------- --------FORCEUNI
1
1
Boolean

Radix
----0/1

PARAMS> set unitnum 21

PARAMS> set forceuni 0
PARAMS> sh forceuni
Parameter Current
Default
Type
--------- ------------ ------------- --------FORCEUNI
0
1
Boolean
PARAMS> write

EF-, RF-, and RZ-Series Integrated Storage Elements 1–33

1.5.4 Setting the ISE Node Name
Setting the ISE node name is an optional step. All DSSI ISEs come with a
computer-generated node name. The user may wish to set this node name to a
more recognizable character string.
The following example changes the node name from the default (R1EJAA) to
the new string "SUSAN." When entering ASCII strings, you may use single
quotes, double quotes, or no quotes at all.
PARAMS> show node
Parameter
Current
Default
Type
Radix
--------- ------------- ------------ ------- ----NODENAME
R1EJAA
RF31
String ASCII

PARAMS> set node "susan"
PARAMS> show node
Parameter
Current
Default
Type
Radix
--------- ------------- ------------ ------- ----NODENAME
SUSAN
RF31
String ASCII

PARAMS> write
NOTE
Using the WRITE command will make any changes permanent.

1.6 Testing the ISE
CAUTION
Running DRVTST may erase all user data on the ISE, and should only
be used when installing a new ISE.

Once the ISE parameters are set, test the drive by using DRVTST, the local
program. DRVTST is accessed in the same way as PARAMS, using one of
the procedures outlined in Section 1.5.1. In this case, instead of specifying
PARAMS, specify DRVTST.
DRVTST is a comprehensive hardware test. Once invoked, it will prompt you
to specify whether the test should be a read/write test or a read-only test.
After you specify the type of test, it will run for 5 minutes. After 5 minutes,
DRVTST will indicate either that the test passed, or that a failure occurred.

1–34 EF-, RF-, and RZ-Series Integrated Storage Elements

Once the ISE has passed DRVTST, the installation is complete. If further
information on the use of DRVTST is desired, refer to the appropriate
integrated storage element user’s guide (see Appendix A) for a complete
description of the DRVTST local program.

1.6.1 DRVTST Example
The following example shows how to run DRVTST. In this example, DRVTST
is accessed through OpenVMS on an ISE with a node name R1EJAA.
$ SET HOST/DUP/SERVER=MSCP$DUP/TASK=DRVTST R1EJAA
The program displays the following:
Copyright © 19nn Digital Equipment Corporation
Write/read anywhere on the medium? [1=Yes/(0=No)]
You must respond to the query for the program to continue. By answering yes
(1), you select a read-write test, and DRVTST prompts you with another query.
In this case, type 1 Return , selecting a read-write test. DRVTST then displays
the following:
User data will be corrupted. Proceed? [1=Yes/(0=No)]
This query gives you the chance to reconsider. If you answer no (0), then your
response to the first query is overridden, and a read-only test is executed. If
you answer yes (1), DRVTST begins executing a read-write test of the ISE.
In this case, type 1 Return . During the test, the program displays the following
message:
5 minutes to complete.
NOTE
You may abort the test at any time by pressing one of the following key
combinations: CTRL/C , CTRL/Y , or CTRL/Z . If you abort the test, the
informational message Operation aborted by user will be displayed.

If DRVTST is executed successfully, the following message is displayed:
Test passed.

EF-, RF-, and RZ-Series Integrated Storage Elements 1–35

1.6.2 Error Messages
If an error condition is found during the execution of DRVTST, an error
message is displayed. Two types of errors are reported: soft errors, which are
corrected during the operation of the ISE, and fatal errors, which prevent the
ISE from functioning.
The following table indicates the error messages you may see and what they
mean.
Table 1–1 DVTST Error Messages
Message

Description

Soft read error on head xx track yyyy.
Soft write error on head xx track yyyy.
Soft compare error on head xx track yyyy.

These are soft error messages which
indicate that an operation succeeded,
but that the error recovery firmware was
invoked. These messages may indicate
a forced-error flag or correctable ECC
error, or that the read/write head was
temporarily off-track. These are corrected
during normal operation.

xxxx - Unit diagnostics failed.

This is a fatal error. xxxx is the MSCP
error code.

xxxx - Unit read/write test failed.

This is a fatal error. xxxx is the MSCP
error code.

Make note of any soft error messages that are displayed for possible future
reference. If you encounter a fatal error, do not complete the installation.

1.7 Setting the SCSI ISE Parameters
Refer to the HSD05 DSSI-to-SCSI Bus Adapter Operation Information for
BA400-Based VAX 4000 Systems manual (EK–HSDC5-IN.) for the procedures
to set the SCSI ISE parameters.

1.7.1 Problem Resolution
Should you encounter problems during installation, refer to the appropriate
system troubleshooting and diagnostics manual.

1–36 EF-, RF-, and RZ-Series Integrated Storage Elements

2
TK-Series Tape Drive
2.1 General
TK-series tape drives (Figure 2–1 and Figure 2–2) are Q–bus devices. A
TK-series tape drive subsystem requires a TQK-series controller module.
Detailed information for configuring TK-series tape drives is contained in the
Microsystems Options manual.

Wr
Pr ite
ote
cte
d

Figure 2–1 TK70 Tape Drive Front Panel

Orange Light
Yellow Light
Green Light
Unload Button

Handle

MLO-002292

TK-Series Tape Drive 2–1

Figure 2–2 TK-Series Tape Drive - Rear View

Data Cable

Interface
Card Assembly

MLO-006529

2.2 TQK-Series Controller Modules
Perform the following procedures to install and configure a TQK-series
controller module.

2–2 TK-Series Tape Drive

2.2.1 Using the CONFIG Utility for Module Configuration and Naming
Each module in a system must use a unique device address and interrupt
vector. The device address is also known as the control and status register
(CSR) address. Most modules have switches or jumpers for setting the CSR
address and interrupt vector values. The value of a floating address depends
on what other modules are housed in the system.
Set CSR addresses and interrupt vectors for a module as follows:
1. Determine the correct values for the module with the CONFIGURE
command at the console I/O prompt (>>>). The CONFIG utility eliminates
the need to boot the VMS operating system to determine CSRs and
interrupt vectors. Enter the CONFIGURE command, then HELP, for the
list of supported devices.
>>>CONFIGURE
Enter device configuration, HELP, or EXIT
Device, Number? help
Devices:
LPV11
KXJ11
DLV11J
RLV12
TSV05
RXV21
DMV11
DELQA
DEQNA
RRD50
RQC25
KFQSA-DISK
RV20
KFQSA-TAPE KMV11
CXA16
CXB16
CXY08
LNV21
QPSS
DSV11
KWV11C ADV11D
AAV11D
DRQ3B
VSV21
IBQ01
IDV11D IAV11A
IAV11B
DESNA
IGQ11
DIV32
KWV32
QZA
Numbers:
1 to 255, default is 1
Device,Number? cxa16,1
Device,Number? desqa,1
Device,Number? tqk70
Device,Number? qza
Device,Number? kfqsa-disk
Device,Number? exit

DZQ11
DRV11W
DESQA
TQK50
IEQ11
VCB01
ADV11C
VCB02
IDV11A
MIRA
KIV32

DZV11
DRV11B
RQDX3
TQK70
DHQ11
QVSS
AAV11C
QDSS
IDV11B
ADQ32
DTCN5

DFA01
DPV11
KDA50
TU81E
DHV11
LNV11
AXV11C
DRV11J
IDV11C
DTC04
DTC05

Address/Vector Assignments
-774440/120 DESQA
-772150/154 KFQSA-DISK
-774500/260 TQK70
-760440/300 CXA16
-761300/310 QZA

TK-Series Tape Drive 2–3

Note
Of the devices listed in the CONFIG display, not all may be supported
on your system. See the Microsystems Options manual for supported
options.
The LPV11–SA has two sets of CSR address and interrupt vectors. To
determine the correct values for an LPV11–SA, enter LPV11,2 at the
DEVICE prompt for one LPV11–SA. Enter LPV11,4 for two LPV11–SA
modules.
2. Once you have determined the correct address for any TK device on the
system, make sure the jumpers on the controller module (Figure 2–3 and
Figure 2–4) are set correctly for that address. See Section 2.2.1.1 for
examples of jumper configurations.
Figure 2–3 TQK-Series Controller Module (TQK50)

LEDs
W13
W14

Unit Number
W12

Hardware
Revision
Level
Address Jumpers

W12, W13, W14,
For Manufacturing Test
Purpose Only
Must Be Installed.

A12

MLO-006532

2–4 TK-Series Tape Drive

Figure 2–4 TQK-Series Controller Module (TQK70)

Unit Select
8

W1 W2

A2
A12
Address Select
W22

MLO-006531

2.2.1.1 Example 1
The following example shows how the jumpers are set for the first logical TK
device. (Assume there are two.) Set the jumpers on the new controller as
follows:

Jumpers
Address

A12
A2
. . . . . . . . . . .
| |
| |
. . . . . . . . . . .
7
4
5
0
0

TK-Series Tape Drive 2–5

2.2.1.2 Example 2
The jumper configuration below signifies the I/O (or CSR) address of 774500 for
unit 0, and 760404 for unit 1. Check that the controller for unit 0 has its unit
number set for unit 0 and that the controller for unit 1 has its unit number set
for unit 1.
A12
A2
. . . . . . . . . . .
Unit 0 | |
| |
. . . . . . . . . . .
7
4
5
0
0
Unit 1

. . . . . . . . . .
|
. . . . . . . . . .
6
0
4
0

.
|
.
4

On a TQK70 module you can select the unit number by installing the Unit
Select jumpers as shown in the following table. If the OpenVMS operating
system is installed, you do not have to change the jumper settings.

2–6 TK-Series Tape Drive

Table 2–1 Unit Number Settings
Unit

Jumpers

Number

1 0 = jumper on center and bottom post
2 1 = jumper on center and top post

Note
The unit number settings for a TQK50 module are implemented by
setting a DIP switch on the module (Figure 2–3). Switch 8 of the DIP
switch is located nearest the module edge.

TK-Series Tape Drive 2–7

2.2.2 Removing ISEs
If integrated storage devices (ISEs) are installed in any mass storage slots,
you must remove those devices to route the TQK-series module data cable.
CAUTION
Static electricity can damage integrated circuits. Always use the
antistatic wrist strap and antistatic pad found in the static-protective
field service kit (29-26246-00) when working with the internal parts of
a computer system.
Handle ISEs with care. Dropping or bumping the ISE can damage the
disk surface. Carry or hold the ISE by the underside of the lower metal
bracket to avoid damage to the drive module.

2–8 TK-Series Tape Drive

1. After the system manager shuts down the operating system, open the
enclosure door (refer to Figure 1–10), and set the Power switch to off (0)
(Figure 2–5).
Figure 2–5 Power Switch Location

Power Switch

MLO-006628

TK-Series Tape Drive 2–9

2. Loosen the captive Phillips screw (at the top) that secures the blank ISE
panel (70-27049-01) and filler panel (70-27414-01) in mass storage slot 0.
Slot 0 is the right-most mass storage cavity in the top row of the enclosure.
Remove both blank panels.
3. Loosen the captive Phillips screw (at the top) that secures an ISE front
panel (Figure 2–6A).
4. Separate the ISE front panel from the enclosure, taking care not to strain
the remote front panel cable that is connected to the ISE front panel.
5. Unplug the remote front panel cable(s) from the module inside the ISE
front panel (Figure 2–6B) and set the panel aside.
6. Label the ISE with the ID number(s) of the front panel that was removed.
This front panel must be re-installed with the ISE from which it had been
removed so that the unit number (specified by the bus node ID plug) is not
changed.
7. Loosen the upper and lower captive screws that hold the ISE in place
(Figure 2–6C).
8. Using the upper and lower finger cutouts on the ISE brackets, carefully
pull the ISE out of its backplane connector and slide the drive out of the
enclosure. Support the weight of the ISE at the underside of the lower
bracket as the ISE clears the enclosure (Figure 2–6C).
CAUTION
Do not touch the drive module. The drive module contains sensitive
electronic circuitry.

2–10 TK-Series Tape Drive

Figure 2–6 Removing an ISE

Phillips Screw

B
Remote Front
Panel Cable

Captive Screws

Remote Front
Panel Cable

Finger Cutouts

MLO-004210

TK-Series Tape Drive 2–11

2.2.3 Installing the TQK-Series Controller Module and TK-Series Tape
Drive
Install the TQK-series controller module and TK-series tape drive as follows.
1. Install the TQK-series controller module in the first available Q–bus slot
(Figure 2–7).
2. Connect the TQK-series data cable (TK50/TK70: 17-01363-01) to the
module. Route the cable up through the card cage and along the front of
the hollow cavity between the card cage area and mass storage cavity to
slot 0 of the mass storage cavity. Route the cable to the back of slot 0, out
of the hollow cavity, and then to the front of slot 0 (Figure 2–7). Dress
the cable so that it does not interfere with air flow or the re-installation of
ISEs.
Figure 2–7 Installing the TQK-Series Controller Module and Routing the
Data Cable

MLO-006530

2–12 TK-Series Tape Drive

3. Grasp the TQK data cable located in mass storage slot 0, and connect it to
the rear of the TK-series tape drive (Figure 2–8).
Figure 2–8 Attaching the Data Cable to the TK-Series Tape Drive

Data Cable

Interface
Card Assembly

MLO-006529

4. With the TK-series tape drive upright (LEDs at the top), slide the drive
along the guide rails (Figure 2–9A) into mass storage slot 0. Tape drives
install only into mass storage slot 0.
5. Using the upper and lower finger cutouts on the drive brackets,
(Figure 2–9A) firmly push the drive brackets until the interface card
at the rear of the drive plugs into its backplane connector. Be careful not
to pinch the cable when inserting the drive.
6. Tighten the two captive screws (Figure 2–9A).
CAUTION
It is normal for there to be a small gap between the drive mounting
bracket tabs and the enclosure frame. Tighten the captive screws only
until they are securely fastened (9 inch pounds). Do not try to force the
tabs to fit flush against the frame.

TK-Series Tape Drive 2–13

Figure 2–9 Installing a TK-Series Tape Drive

A
Captive
Screws

Finger
Cutouts

Captive
Phillips
Screw

MLO-006534

7. Attach the drive front panel to the enclosure by first fitting the panel’s
lower tabs into position. Secure the panel with its single captive Phillips
screw (Figure 2–9B).

2–14 TK-Series Tape Drive

To replace the ISEs, reverse the procedure in Section 2.2.2. For additional
information on removing and replacing the ISEs, refer to the appropriate
BA400-series enclosure maintenance guide (see Appendix A).
The ISEs and tape drive are shown installed in Figure 2–10.
Figure 2–10 ISEs and Tape Drive Installed
Slot 3

Slot 2

Slot 1

Slot 0

MLO-006528

TK-Series Tape Drive 2–15

2.3 Power-On Self-Test
The tape drive board contains firmware that enables testing of basic drive
functions. Faults are indicated by the LED indicators on the front panel and
error codes are sent to the controller.

2.3.1 TK70 Tape Drive POST
Use the following procedure to execute the POST.
1. Power on the system.
•

All three indicators (orange, yellow, and green) light (see Figure 2–1.)

•

The yellow indicator flashes for about 15 seconds indicating that the
self-test is running.

Successful POST
After successful completion of the POST:
•

The green indicator remains on indicating that you can now operate the
handle and install a tape cartridge.

•

All other indicators shut off.

After completing a successful execution of the POST, have the system manager
restart the operating system and assign a device name to the TK70 drive.
Unsuccessful POST
The POST failed if all three indicators continue to flash.
Attempt to clear the failure by pressing and releasing the Unload Button
(see Figure 2–1).
If the failure continues, refer to the appropriate system troubleshooting
and diagnostics manual (Appendix A).

2–16 TK-Series Tape Drive

2.3.2 TK50 Tape Drive POST
Use the following procedure to execute the POST.
1. Power on the system.
•

The red indicator flashes for about 15 seconds to indicate that the
self-test is running (see Figure 2–11).

•

The green indicator remains off.

Successful POST
After successful completion of the POST:
•

The red indicator stops flashing and shuts off.

•

The green indicator lights indicating that you can now operate the handle
and install a tape cartridge.

After completing a successful execution of the POST, have the system manager
restart the operating system and assign a device name to the TK50 drive.
Unsuccessful POST
The POST failed if the red indicator continues to flash.
Attempt to clear the failure by pressing and releasing the LOAD/UNLOAD
button four times.
If the failure continues, refer to the appropriate system troubleshooting
and diagnostics manual (Appendix A).

TK-Series Tape Drive 2–17

Figure 2–11 TK50 Tape Drive Front Panel
Load/Unload
Button,
Red Light

Handle Closed

Green
Indicator
Light
MLO-006586

2–18 TK-Series Tape Drive

3
TLZ-Series Tape Drives
3.1 General
This chapter describes how to install the TLZ-series tape drive. For more
detailed information about installing add-on storage devices into a BA400series enclosure, refer to the appropriate enclosure maintenance guide (see
Appendix A).

3.2 TLZ04 Tape Drive
The TLZ04 tape drive (Figure 3–1) is a 5.25-inch tape drive with a data storage
capacity of 1.2 gigabytes. The TLZ04 tape drive interfaces to the system by
means of a Small Computer System Interface (SCSI).

TLZ-Series Tape Drives 3–1

Figure 3–1 TLZ04 Tape Drive

MLO-006535

3.3 TLZ04 Installation Procedure
Use the following procedure to install the tape drive into a BA400-series
enclosure. Have the system manager shut down the operating system before
installing the tape drive.
CAUTION
Static electricity can damage integrated circuits. Use the antistatic
wrist strap and antistatic pad found in the static-protective field service
kit (29-26246-00) when you work with the internal parts of a computer
system.

1. Open the top and bottom enclosure doors.
2. Power off the system and unplug the power cord from the wall outlet.
3. Loosen the captive Phillips screw (at the top) and remove the drive front
panel and filler panel located in mass storage slot 0.

3–2 TLZ-Series Tape Drives

Figure 3–2 Opening the Enclosure Doors

Key Lock

Top Key Position

MLO-004034

Slot 0

Power
Switch

MLO-004035

Bottom Key Position
MLO-012856

TLZ-Series Tape Drives 3–3

4. With the tape drive right side up (LEDs at top), slide the drive
(Figure 3–3A) into mass storage slot 0.
5. Using the tabs in front of the upper and lower finger cutouts, firmly push
the drive brackets until the interface card at the rear of the drive plugs
into its backplane connector.
6. Refer to Figure 3–3 to complete the installation of the drive.
a. Tighten the two captive screws at the top and bottom of the bracket
(A).
CAUTION
It is normal for there to be a small gap between the mounting bracket
tabs and the enclosure frame. Tighten the captive screws only until
they are securely fastened (9 inch pounds). Do not try to force the tabs
to fit flush against the frame.

7. Plug the ID cable into the connector inside the drive front panel (B).
8. Attach the drive front panel to the enclosure by first fitting the panel’s
lower tabs into position and then securing the panel with its single captive
Phillips screw (C).
9. Insert the proper SCSI node ID plug into the front panel.
See Section 3.8 for additional information about the SCSI bus node ID
plug.

3–4 TLZ-Series Tape Drives

Figure 3–3 Installing the TLZ04 Drive

25.5%

Captive Screws (2)

Finger Cutouts

ID Cable
Guide Tabs
Phillips Screw

C
ID Cable

30%
MLO-005788

TLZ-Series Tape Drives 3–5

3.4 Completing the TLZ04 Installation
This section explains how to verify the correct operation of the TLZ04 tape
drive by performing the power-on self-test (POST).

3.4.1 TLZ04 Power-On Self-Test
Use the following procedure to execute the POST.
1. Power on the system.
•

The tape and drive indicators flash for approximately 30 seconds.

Successful POST
After successful completion of the POST, the Tape Activity indicator:
•

Shuts off if there is no cassette in the drive.

•

Remains on if there is a cassette in the drive.

After completing a successful execution of the POST, have the system manager
restart the operating system and assign a device name to the TLZ04 drive.
Unsuccessful POST
If the Tape and Drive indicators continue to flash for more than 30 seconds,
then the POST has failed.
Attempt to clear the failure by powering off the system and then reexecuting the POST.
If the failure continues, refer to the appropriate system troubleshooting
and diagnostics manual (Appendix A).

3–6 TLZ-Series Tape Drives

3.5 TLZ07 Tape Drive
The TLZ07 is a 5.25-inch half-height cassette tape drive that provides high
capacity, off-line data storage. The TLZ07 interfaces to the system by means
of a Small Computer System Interface (SCSI). The following table lists the
storage capacity for each type of 4 mm data cassette.
Tape Type

With No Compression

With Compression

1.3 GB

2.6 GB

TLZ06-CA (90 m)

2.0 GB

4.0 GB3

TLZ07-CA (120 m)

4.0 GB

8.0 GB3

TLZ04-CA (60 m)

1 The TLZ07 is compatible with TLZ04 (60 m) cassette tapes in the noncompressed mode only.
2 The TLZ07 is compatible with the TLZ06 using 60 m and 90 m tapes only.
3 The compression measurements are typical for a 2-to-1 data compression ratio, but the actual

ratio is dependent on the data.

Note
VAX 4000 systems do not support TLZ07 tape drives unless an HSD05
option is installed.

TLZ-Series Tape Drives 3–7

3.6 TLZ07 Installation Procedure
Use the following procedure to install the TLZ07 tape drive into a BA400-series
enclosure. Have the system manager shut down the operating system before
installing the tape drive.
CAUTION
Static electricity can damage integrated circuits. Use the antistatic
wrist strap and antistatic pad found in the static-protective field service
kit (29-26246-00) when you work with the internal parts of a computer
system.

3–8 TLZ-Series Tape Drives

Figure 3–4 Opening the Enclosure Doors

Key Lock

Top Key Position

MLO-004034

Slot 0

Power
Switch

MLO-004035

Bottom Key Position
MLO-012856

TLZ-Series Tape Drives 3–9

4. With the tape drive left side down (LEDs at the bottom), slide the drive
into mass storage slot 0.
Using the tabs in front of the upper and lower finger cutouts, firmly
push the drive bracket into the enclosure until the interface card at the
rear of the drive plugs into its backplane connector.
5. Refer to Figure 3–5 to complete the drive installation.
a. Tighten the captive screws at the top and bottom of the bracket (1).
CAUTION
It is normal for there to be a small gap between the mounting bracket
tabs and the enclosure frame. Tighten the captive screw only until it
is securely fastened (9 inch pounds). Do not try to force the tabs to fit
flush against the frame.

b. Plug the SCSI ID cable into the bottom connector inside the drive front
panel (2).
c.

Attach the drive front panel to the enclosure by first fitting the panel’s
lower tabs into position (3).

d. Secure the front panel with its single captive Phillips screw (4).
e.

Insert the proper SCSI node ID plug into the front panel (5).
See Section 3.8 for information about choosing the proper SCSI ID
plug.

3–10 TLZ-Series Tape Drives

Figure 3–5 Installing the TLZ07 Drive

Tighten
screw.

Insert
SCSI ID
connector.
8
7
6
5
4
3
F
F
O

Insert
SCSI
ID plug.

2
1

Insert
bezel.

MLO-012820

TLZ-Series Tape Drives 3–11

3.7 Completing the TLZ07 Installation
This section explains how to verify successful installation of the TLZ07 drive
by performing the power-on self-test (POST), and then assigning a device name
to the drive.

3.7.1 TLZ07 Power-On Self-Test
Use the following procedure to execute the POST:
1. Power on the system.
•

If there is no cassette in the drive:
The Cassette and Write-Protect indicators flash for approximately 1 to
5 seconds and then shut off.

•

If there is a cassette in the drive:
The Cassette and Write-Protect indicators flash for approximately 5
seconds, then the Write-Protect indicator indicates write-protect status
and the Cassette indicator continues to flash at a slower rate until the
cassette is loaded. After the cassette is loaded, the Casette indicator
remains on.

After completing a successful execution of the POST, have the system manager
restart the operating system and assign a device name to the TLZ07 drive.
Unsuccessful POST
The POST failed if the Cassette and Write-Protect indicators flash continuously
for more than 30 seconds.
Attempt to clear the failure by powering off the system and then reexecuting the POST.
If the failure continues, refer to the appropriate system troubleshooting
and diagnostics manual (Appendix A).

3–12 TLZ-Series Tape Drives

3.8 Bus Node ID Plug
The TLZ-Series tape drives use a bus node ID plug to identify, or address, the
drive. The bus node ID the drive uses is dependent on other SCSI devices in
the system. The ID must be unique for each device on the bus.
Prongs at the back of the bus node ID plugs identify the bus node ID number
(and by default, the unit number) of the drive to the system. Bus node ID
plugs are shipped with the host system or host expander.
To insert a bus node ID plug, align the two center prongs with the two center
slots of the receptacle in the front panel assembly. Push the plug firmly into
the receptacle. To remove a bus node ID plug, grasp it firmly and pull it
straight out.
NOTE
If you change the bus node ID plugs while the system is operating, you
must turn off the system and then turn it back on for the new plug
positions to take effect.

TLZ-Series Tape Drives 3–13

4
RRD-Series CD–ROM Drive
4.1 General
RRD-Series CD–ROM drives are compact disc, read-only memory (ROM),
Small Computer System Interface (SCSI) devices. These drives read data
from industry standard 600-MB discs. To meet the requirements of a wide
variety of applications, the RRD-series of CD–ROM drives support all CD–
ROM standards including CD–ROM-XA (CD–ROM-eXtended Architecture),
Multisession Photo CD, and MPC (Multimedia Products Council) 1 and 2, and
is CD-I ready.

4.2 Installation Procedure
Use the following procedure to install the RRD-series CD–ROM drives into the
BA400-series enclosure. Have the system manager shut down the operating
system before installing the CD–ROM drive.
CAUTION
Static electricity can damage integrated circuits. Use the antistatic
wrist strap and antistatic pad found in the static-protective field service
kit (29-26246-00) when you work with the internal parts of a computer
system.

RRD-Series CD–ROM Drive 4–1

1. Open the top and bottom enclosure doors.
2. Power off the system and unplug the power cord from the wall outlet.
3. Loosen the captive Phillips screw (at the top) and remove the front panel
from the first available storage slot.
Note
The first mass storage cavity in the mass storage area (slot 0) is wider
than the rest to accommodate a large device, such as a tape drive.
A small filler panel (70-27414-01) is used to fill the gap when an
RRD-series ISE is installed in this first cavity.

4–2 RRD-Series CD–ROM Drive

Figure 4–1 Opening the Enclosure Doors

Key Lock

Slot 3
Slot 2
Slot 1
Top Key Position

MLO-004034

Power
Switch

MLO-004035

Bottom Key Position
MLO-012857

RRD-Series CD–ROM Drive 4–3

4. Refer to Figure 4–2 to install the CD–ROM drive into the mass storage
slot:
Using the tabs in front of the upper and lower finger cutouts, firmly
push the drive brackets until the interface card at the rear of the drive
plugs into its backplane connector (A).
5. Tighten the captive screws at the top and bottom of the bracket (A).
CAUTION
It is normal for there to be a small gap between the mounting bracket
guide tabs and the enclosure frame. Tighten the captive screw only
until it is securely fastened (9 inch pounds). Do not try to force the
tabs to fit flush against the frame.

6. Plug the SCSI ID cable into the connector inside the drive front panel (B).
7. Attach the ISE front panel to the enclosure by first fitting the panel’s lower
tabs into position.
Fit the panel into position and secure the panel with its single captive
Phillips screw (C).
8. Insert the proper SCSI node ID plug in the front panel (C).
See Section 4.3.2 for additional information about the SCSI bus node
ID plug.
9. If you do not have a KZQSA installed, go to Section 4.3 to complete the
installation.
If you do have a KZQSA installed, continue with the next step.

4–4 RRD-Series CD–ROM Drive

Figure 4–2 Inserting the RRD CD–ROM drive

25.5%
25.5%

Captive Screw

Finger Cutouts

Guide Tabs
ID Cable
Phillips Screw

30%

SCSI
ID Plug

MLO-012842

RRD-Series CD–ROM Drive 4–5

10. Locate the KZQSA IN connector on the I/O bulkhead.
Figure 4–3 KZQSA IN Connector

KZQSA In

MLO-007150

4–6 RRD-Series CD–ROM Drive

11. Remove the protective cover from the KZQSA IN connector.
Figure 4–4 Removing the Connector Cover

Protective Cover

MLO-007168

12. Locate the KZQSA internal cable labeled BC06P–2F that ships with the
RRD drive.
Figure 4–5 KZQSA Cable

MLO-007151

RRD-Series CD–ROM Drive 4–7

13. Connect one end of the cable to the KZQSA IN connector.
Press the bail latches onto the cable connector to lock it in place.
Figure 4–6 Connecting to KZQSA IN

MLO-007152

14. Locate the KZQSA module identified by the KZQSA-SA indentification
label on the module cover.

4–8 RRD-Series CD–ROM Drive

Figure 4–7 KZQSA Label

KZQSA
-SA
M5976
-SA

MLO-007153

15. Remove the terminator from the upper connector on the module.
Figure 4–8 KZQSA Module Connector

MLO-007179

RRD-Series CD–ROM Drive 4–9

16. Connect the other end of the cable to the KZQSA module connector.
Press the bail latches onto the cable connector to lock it in place.
Figure 4–9 Connecting to KZQSA IN

97
M5A
-S

Bail
Latch

Feed Cable Under System
and Up Through Opening.

MLO-007154

4.3 Completing the Installation
This section explains how to verify successful installation of the RRD
CD–ROM drive by performing the power-on self-test (POST).

4–10 RRD-Series CD–ROM Drive

4.3.1 RRD CD–ROM Power-On Self-Test
Use the following procedure to execute the POST:
1. Power on the system.
•

The Busy indicator flashes for approximately 10 to 20 seconds.

Successful POST
After successful completion of the POST, the Busy indicator shuts off.
Have the system manager restart the operating system and assign a device
name to the CD–ROM drive.
Unsuccessful POST
If the Busy indicator remains on continuously then the POST failed.
Attempt to clear the failure by powering off the system and then reexecuting the POST.
Check to be sure the CD is not loaded upside-down.
Check and reseat all ISE cable connections.
If the failure continues, refer to the appropriate system troubleshooting
and diagnostics manual (Appendix A).

RRD-Series CD–ROM Drive 4–11

4.3.2 Bus Node ID Plug
The RRD-Series CD–ROM drives use a bus node ID plug to identify, or address,
the RRD drive. The bus node ID that the RRD drive uses is dependent on other
SCSI devices in the system. The ID must be unique for each device on the bus.
Bus node ID plugs have prongs on their backs that identify the bus node ID
number (and by default, the unit number) of the RRD drive to the system. Bus
node ID plugs are shipped with the host system or host expander.
To insert a bus node ID plug, align the two center prongs with the two center
slots of the receptacle in the front panel assembly (Figure 4–2 (C)). Push the
plug firmly into the receptacle. To remove a bus node ID plug, grasp it firmly
and pull it straight out.
NOTE
If you change the bus node ID plugs while the system is operating, you
must turn off the system and then turn it back on for the new plug
positions to take effect.

4–12 RRD-Series CD–ROM Drive

5
RRD/TLZ07 Dual ISE Drives
5.1 General
This chapter describes how to install the RRD/TLZ07 Dual ISE in the BA400series enclosure. The RRD/TLZ07 Dual ISE contains a multi-purpose CD–ROM
drive and a 5.25-inch cassette tape drive.
Note
VAX 4000 systems do not support the RRD/TLZ07 Dual ISE unless an
HSD05 option is installed.

RRD/TLZ07 Dual ISE Drives 5–1

5.2 Installation Procedure
Use the following procedure to install the dual ISE drives into a BA400-series
enclosure. Have the system manager shut down the operating system before
installing the ISE.
CAUTION
Static electricity can damage integrated circuits. Use the antistatic
wrist strap and antistatic pad found in the static-protective field service
kit (29-26246-00) when you work with the internal parts of a computer
system.

5–2 RRD/TLZ07 Dual ISE Drives

Key Lock

Top Key Position

MLO-004034

Slot 0

Power
Switch

MLO-004035

Bottom Key Position
MLO-012856

RRD/TLZ07 Dual ISE Drives 5–3

4. Remove the center (plastic) card guides from the top and bottom storage
divider in slot 0 (the guides are a pressure fit and lift right out).
5. With the tape drive left side down (LEDs at the bottom), slide the drive
into mass storage slot 0.
Using the tabs in front of the upper and lower finger cutouts, firmly
push the drive bracket into the enclousure until the interface card at
the rear of the drive plugs into its backplane connector.
6. Refer to Figure 5–1 to complete the installation of the drives.
a. Tighten the captive screws at the top and bottom of the bracket (1).
CAUTION
It is normal for there to be a small gap between the mounting bracket
tabs and the enclosure frame. Tighten the captive screws only until
they are securely fastened (9 inch pounds). Do not try to force the tabs
to fit flush against the frame.

b. Plug the TLZ07 SCSI ID cable into the bottom connector inside the
drive front panel (2).
c.

Plug the RRD SCSI ID cable into the top connector inside the drive
front panel (2).

d. Attach the drive front to the enclosure by first fitting the panel’s lower
tabs into position (3).
e.

Secure the front panel with its single captive Phillips screw (4).

Insert the proper SCSI node ID plug into the top receptacle of the front
panel for the RRD CD–ROM (5).
See Section 5.3.3 for additional information about the SCSI bus
node ID plug.

g. Insert the proper SCSI node ID plug into the bottom receptacle of the
front panel for the TLZ07 tape drive (5).
See Section 5.3.3 for additional information about the SCSI bus
node ID plug.

5–4 RRD/TLZ07 Dual ISE Drives

Figure 5–1 Installing the RRD/TLZ07 Dual ISE

Tighten
screw.

Insert
SCSI ID
connectors.
8
7
6
5
4
3
F
F
O

Insert
SCSI
ID plugs.

2
1

Insert
bezel.

MLO-012858

RRD/TLZ07 Dual ISE Drives 5–5

5.3 Completing the Installation
This section explains how to verify correct installation of the RRD/TLZ07 dual
ISE drives by performing the power-on self-test (POST).
Section 5.3.1 describes the POST for a CD–ROM drive.
Section 5.3.2 describes the POST for a TLZ07 tape drive.

5.3.1 RRD CD-ROM Power-On Self-Test
Use the following procedure to execute the POST:
1. Power on the system.
•

The Busy indicator flashes for approximately 10 to 20 seconds.

5–6 RRD/TLZ07 Dual ISE Drives

5.3.2 TLZ07 Power-On Self-Test
Use the following procedure to execute the POST:
1. Power on the system.
•

If there is no cassette in the drive:
The Cassette and Write-Protect indicators flash for approximately 1 to
5 seconds and then shut off.

•

If there is a cassette in the drive:
The Cassett and Write-Protect indicators flash for approximately 5
seconds, then the Write-Protect indicator indicates write-protect status
and the Cassette indicator continues to flash at a slower rate until the
cassette is loaded. After the cassette is loaded, the Cassette indicator
remains on.

RRD/TLZ07 Dual ISE Drives 5–7

5.3.3 Bus Node ID Plug
The RRD CD–ROM drive and the TLZ07 tape drive each use a bus node ID
plug to identify, or address, the drives. The bus node ID that each drive uses
is dependent on other SCSI devices in the system. The ID must be unique for
each device on the bus.
Prongs on the back of bus node ID plugs identify the bus node ID number (and
by default, the unit number) of the drives to the system. Bus node ID plugs
are shipped with the host system or host expander.
To insert a bus node ID plug, align the two center prongs with the two center
slots of the receptacle in the front panel assembly (Figure 5–1). Push the plug
firmly into the receptacle. To remove a bus node ID plug, grasp it firmly and
pull it straight out.
NOTE
If you change the bus node ID plugs while the system is operating, you
must turn off the system and then turn it back on for the new plug
positions to take effect.

5–8 RRD/TLZ07 Dual ISE Drives

6
TF/TZ-Series Tape Drive
6.1 General
This chapter describes how to install the TF/TZ-series of tape drive. Figure 6–1
shows the front panel of the TF85 tape drive and is representative of this series
of drives.

Tape In Use
Yellow
Use Cleaning Tape
Orange
Operate Handle
Green

To
Re Han Op
P
W
Un
ait res
d e
m
lo
s
ov le n t
ad
his
e
Lig But
Ta
to
ht
pe
n

Write Protected
Orange

lo
Un

Unload
Button

To
H
Ha C
O
Lo
nd los Inse and pe Wa
it
ad
le n
le e
r
th
th t Ta
Lig
is
is
pe
ht

W
rit
Pr e
ot
ec

te
d
pe
in
Us
Us
e
e
Cle
Ta anin
pe g
O
pe
Ha rat
nd e
le

Figure 6–1 TF85 Tape Drive Front Panel

Cartridge Insert/
Release Handle

Bus Node
ID Plug
MLO-006543

The Digital Linear Tape Drive (DLT) family cartridge tape drives are 5.25-inch
streaming linear recording tape devices, designed for systems requiring high
performance, high data integrity, and unattended backup.
The DLT cartridge tape drive subsystems use the CompacTape III cartridge,
which contains 335 meters (1100 feet) of half-inch-wide metal powder (MP)
tape.

TF/TZ-Series Tape Drive 6–1

The TF/TZ-series cartridge tape subsystems are used primarily for data
backup, for data archiving, and for loading software onto computer systems.
The TZ-series cartridge tape subsystems use the Small Computer System
Interface (SCSI) bus. The TF-series cartridge tape subsystems use the Digital
Storage Systems Interconnect (DSSI) bus.

6.2 TF/TZ-Series Tape Drive Installation
Use this procedure to install TF/TZ-Series tape drives.
NOTE
VAX 4000 systems do not support TZ-series ISEs unless an HSD05
option is installed.

CAUTION
Static electricity can damage integrated circuits. Use the antistatic
wrist strap and antistatic pad found in the static-protective field service
kit (29-26246-00) when you work with the internal parts of a computer
system.
Handle the TF/TZ-series tape drive with care. Dropping or bumping
the drive can damage the product. Carry or hold the drive by the
underside of the lower metal bracket to avoid damaging the drive
module.

6–2 TF/TZ-Series Tape Drive

1. After the system manager shuts down the operating system, open the
enclosure door (refer to Figure 1–10), and set the power switch to off (0)
(Figure 6–2).
Figure 6–2 Power Switch Location

Power Switch

MLO-006628

TF/TZ-Series Tape Drive 6–3

2. Loosen the captive Phillips screws (at the top) and remove the blank front
panel (70-27049-01) and filler panel (70-27414-01) located in mass storage
slot 0.
Note
The TF/TZ-series tape drive is installed only in mass storage slot 0.

3. With the tape drive right side up (Unload button at top), slide the drive
(Figure 6–3A) into mass storage slot 0.
4. Using the tabs in front of the upper and lower finger cutouts, firmly push
the drive brackets until the interface card at the rear of the drive plugs
into its backplane connector.
5. Refer to Figure 6–3 to complete the installation of the drive.
a. Tighten the two captive screws at the top and bottom of the bracket
(A).
CAUTION
It is normal for there to be a small gap between the mounting bracket
tabs and the enclosure frame. Tighten the captive screws only until
they are securely fastened (9 inch pounds). Do not try to force the tabs
to fit flush against the frame.

b. Plug in the ID cable:
For TF-series tape drives, plug the connector from the front panel
(B1) to the front of the ISE controller board (A).
For TZ-series tape drives, plug the connector from the ISE
controller board (A) to the front panel connector (B2).
c.

Attach the ISE front panel to the enclosure by first fitting the panels
lower tabs into position.
Fit the panel into position and secure the panel with its single
captive Phillips screw (C).

6–4 TF/TZ-Series Tape Drive

Figure 6–3 Installing the TF/TZ-Series Drive

A
Finger Cutouts
Captive Screws (2)

Remote ID Cable
Connector (TZ87)
Remote ID Cable
Connector
(TF-Series, TZ86)

B1
Guide Tabs

Phillips Screw
ID Cable

C
B2

ID Cable

MLO-012864

TF/TZ-Series Tape Drive 6–5

Figure 6–4 shows the TF/TZ-series tape drive installed in the
enclosure.
Figure 6–4 TF/TZ-Series Drive Installed in Mass Storage Slot 0
Slot 3

Slot 2

Slot 1

Slot 0

MLO-006528

6–6 TF/TZ-Series Tape Drive

6.3 Completing the Installation
This section explains how to verify successful installation of the TF/TZ-series
tape drives by performing the power-on self-test (POST).

6.3.1 TF/TZ-Series Power-On Self-Test
When the TF/TZ-series subsystem is powered on, the drive performs the
power-on self-test (POST). The sequence of events are listed in Table 6–1.
Table 6–1 Power-on Self-test Events
Stage

What Happens

The indicators on the TF/TZ-series top front panel light sequentially,
from left to right and then stay on for a few seconds.

All indicators on the TZ87 bottom front panel light at the same time for
about three seconds and then shut off.

The green Operate Handle, the orange/yellow Write Protected1 , and the
yellow Use Cleaning Tape indicators shut off.

The yellow Tape in Use indicator flashes while the tape drive initializes.

After initialization, with no cartridge loaded, the green Operate Handle
indicator lights and a ‘‘beep’’ sounds.

1 The Write Protected indicator is yellow on the TZ87 tape drive, and orange on the TZ86 and
TF-series tape drives.

Successful POST
POST completes in about 13 seconds and the subsystem responds normally to
all commands. However, it might take longer for the media to become ready.
After a bus reset, the tape drive responds with a bus selection timeout period.
After completing a successful execution of the POST, have the system manager
restart the operating system and assign a device name to the TF/TZ-series
drives.
Unsuccessful POST
The POST failed if all indicators continue to flash.
Attempt to clear the failure by powering off the system and then reexecuting the POST.
If the failure continues, refer to the appropriate system troubleshooting
and diagnostics manual (Appendix A).

TF/TZ-Series Tape Drive 6–7

6.4 Setting the ISE Parameters
Once the tape drive passes power-on self-test, the DSSI parameters must be
set. For TF-series tape drives this is done in the same manner as the RF-series
ISEs (refer to the procedure in Section 1.5).
For TZ-series tape drives the SCSI ISE parameters are set in the same
manner as the RZ-series ISEs. Refer to the HSD05 DSSI-to-SCSI Bus
Adapter Operation Information for BA400-Based VAX 4000 Systems manual
(EK–HSDC5–IN.) for this procedure.

6–8 TF/TZ-Series Tape Drive

A
Related Documentation
Document

Order Number

BA430/BA440 Enclosure Maintenance

EK–348A*–MG

EFxx-Series Solid State Disk User Guide

EK–EF51x–UG

Microsystems Options

EK–192A*–MG

MicroVAX Diagnostic Monitor User’s Guide

AA–FM7A*–DN

R400X Expander Installation and Maintenance

EK–349A*–MG

RF Series Integrated Storage Element User Guide

EK–RF72D–UG

TF85 Cartridge Tape Subsystem Owner’s Manual

EK–OTF85–OM

TX86 Series Cartridge Tape Subsystems

EK–OTX86-OM

TZ87 Cartridge Tape Subsystems

EK–OTZ87-OM

BA400 Series Mass Storage Devices

EK–441AC–IP

HSD05 DSSI-to-SCSI Bus Adapter Operation Information
for BA400-Based VAX 4000 Systems

EK–HSDC5–IN

Note
* Indicates the revision code. The latest revision is always shipped
when a manual is ordered.