Digital PDFs

EK-512AA-IN-B01

May 1995

20 pages

Original

0.6MB

Document:	VAX 4000 Model 105A Installation Information
Order Number:	EK-512AA-IN
Revision:	B01
Pages:	20
Original Filename:

OCR Text

VAX 4000 Model 105A/106A
Installation Information
Order Number: EK–512AA–IN. B01

May 1995
This manual describes how to install and test the VAX 4000 Model 105A
and Model 106A.

Digital Equipment Corporation
Maynard, Massachusetts

May 1995
Digital Equipment Corporation makes no representations that the use of its products in the
manner described in this publication will not infringe on existing or future patent rights, nor do
the descriptions contained in this publication imply the granting of licenses to make, use, or sell
equipment or software in accordance with the description.
Possession, use, or copying of the software described in this publication is authorized only
pursuant to a valid written license from Digital or an authorized sublicensor.
© Digital Equipment Corporation 1995. All Rights Reserved.
The postpaid Reader’s Comments forms at the end of this document request your critical
evaluation to assist in preparing future documentation.
The following are trademarks of Digital Equipment Corporation: DEC, Digital, ThinWire, VAX,
VAX DOCUMENT, VMS, and the DIGITAL logo.
All other trademarks and registered trademarks are the property of their respective holders.
S2849

This document was prepared using VAX DOCUMENT Version 2.1.

Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 Installation Procedure
Step 1: Choosing a Suitable Location . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 2: Unpacking the System and Identifying the Parts . . . . . . . . . . . .
Step 3: Connecting the Console Terminal . . . . . . . . . . . . . . . . . . . . . . . .
Step 4: Connecting the ThinWire Terminator . . . . . . . . . . . . . . . . . . . . .
Step 5: Connecting the SCSI Terminator . . . . . . . . . . . . . . . . . . . . . . . . .
Step 6: Connecting the DSSI Terminators . . . . . . . . . . . . . . . . . . . . . . . .
Step 7: Connecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 8: Turning on the Console Terminal and System Unit . . . . . . . . . . .
Step 9: Checking the Power-Up Test Results . . . . . . . . . . . . . . . . . . . . . .
Step 10: Connecting the System to a Network . . . . . . . . . . . . . . . . . . . . .
Step 11: Connecting External Options to the System . . . . . . . . . . . . . . .
Step 12: Booting the Operating System . . . . . . . . . . . . . . . . . . . . . . . . . .

1–1
1–2
1–3
1–4
1–5
1–6
1–8
1–9
1–10
1–12
1–12
1–12

Examples
1–1
1–2

Successful Power-Up Test Screen . . . . . . . . . . . . . . . . . . . . . .
Unsuccessful Power-Up Test Screen . . . . . . . . . . . . . . . . . . . .

1–10
1–11

The VAX 4000 Model 105A/106A Systems . . . . . . . . . . . . . . .
Console Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ThinWire Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the SCSI Terminator . . . . . . . . . . . . . . . . . . . . . .
Connecting a DSSI Terminator to a VAX 4000 Model
105A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1–2
1–3
1–4
1–5

Figures
1–1
1–2
1–3
1–4
1–5

1–6

iii

1–6
1–7
1–8

Connecting a DSSI Terminator to a VAX 4000 Model
106A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Cord Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Turn On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1–7
1–8
1–9

Preface
This manual describes how to install and test VAX 4000 Model 105A and
Model 106A systems. It also refers to information on connecting the system to
a network, connecting external options to the system, and booting the operating
system.

Audience
This manual is intended for anyone who wants to install VAX 4000
Model 105A/106A systems. It is written for both experienced and inexperienced
users.

Structure of This Manual
This manual contains one chapter. Each section heading is a step in the
installation procedure and is indicated by the word step and a numeral.
Substeps in the procedure are indicated by a numeral.

Additional Information
See the VAX 4000 Model 105A/106A Operator Information manual for the list
of associated and related documents.

Conventions
The following conventions are used in this manual:

Convention

Description

MONOSPACE

Text displayed on the screen is shown in monospace type.

italic type

Italic type emphasizes important information and indicates the
complete titles of manuals.

Note

A note contains information that is of special importance to the user.

1
Installation Procedure
This chapter shows you, step by step, how to install VAX 4000 Model 105A and
Model 106A systems.
Note
Illustrations in this manual show a VAX 4000 Model 106A system
rather than a Model 105A system, unless otherwise noted.

Step 1: Choosing a Suitable Location
Follow these guidelines when choosing where to place the system unit:
•

Place the system unit where the room temperature is between 10°C and
40°C (50°F and 104°F) and the humidity is between 20% and 80%.

•

Place the system unit at least 1 metre (3 feet) from heaters, photocopying
machines, or other operating equipment.

•

Place the system unit in a well-ventilated location.

•

Place the system unit on a work surface that is raised above the floor.

•

Do not place this unit on the top of any pedestal system.

•

Keep the air vents on either side of the system unit clear.

•

Do not expose the system unit to direct sunlight or abrasive particles.
Note
The console terminal is not supplied with the system.

Installation Procedure 1–1

Step 2: Unpacking the System and Identifying the Parts
1. Unpack the system.
2. Make sure that you have all the parts listed on the packing slip. The
loose-piece accessory kit is shipped with all basic systems. If you do not
have all the parts listed, contact your Digital Sales representative.
Figure 1–1 The VAX 4000 Model 105A/106A Systems

2
4

5
6

7
MLO-009274

! System Unit
" SCSI Terminator H8574-A (PN 12-30552-01)
# One ThinWire™ Ethernet T-Connector (H8223) and Two Terminators
(H8225)

$ DEC423 Console Terminal Cable (BC16E-25)
% DSSI Terminator (12-29258-01) (up to four included)
& Power Cord
' Documentation and Software Licenses

1–2 Installation Procedure

Step 3: Connecting the Console Terminal
1. Connect one end of the terminal cable to the modified modular jack (MMJ)
port 3. This system will be shipped with a label covering ports 0 and 1.
After port 3 is properly identified as the console port, the OPA0 arrow label
may be removed.
2. Connect the other end of the terminal cable to a DEC423 (MMJ)
communications port on the console terminal.
Figure 1–2 Console Connection

3
2

! Terminal Cable

MLO-011868

Installation Procedure 1–3

Step 4: Connecting the ThinWire Terminator
1. Assemble the T-connector and the two terminators to form a ThinWire
terminator.
2. Connect the ThinWire terminator to the system unit.
Figure 1–3 ThinWire Termination

3
2

MLO-011869

! T-Connector
" Terminator

1–4 Installation Procedure

Step 5: Connecting the SCSI Terminator
1. Connect the SCSI terminator to the SCSI port.
2. Close the bail lock loops.
Figure 1–4 Connecting the SCSI Terminator

3
2

! SCSI Terminator

MLO-011870

Installation Procedure 1–5

Step 6: Connecting the DSSI Terminators
Connect all DSSI terminators.
Note
The VAX 4000 Model 105A has an expansion port with three DSSI slots
(see Figure 1–5). The VAX 4000 Model 106A has four DSSI slots on the
expansion port (see Figure 1–6).

Figure 1–5 Connecting a DSSI Terminator to a VAX 4000 Model 105A

2
1

3
2

MLO-010203

! DSSI Terminator for all models
" Connected DSSI Terminators
1–6 Installation Procedure

Figure 1–6 Connecting a DSSI Terminator to a VAX 4000 Model 106A

1
2

3
2

MLO-011871

! DSSI Terminator for all models
" Connected DSSI Terminators

Installation Procedure 1–7

Step 7: Connecting the Power Cord
1. Ensure that the on/off switch is in the off (O) position (see Figure 1–8 for
switch location).
2. Connect the power cord to the system unit.
3. Connect the other end of the power cord to an isolated, grounded circuit.
Figure 1–7 Power Cord Connection

3
2

! Power Cord

1–8 Installation Procedure

MLO-011872

Step 8: Turning on the Console Terminal and System Unit
1. Turn on the console terminal. Wait until it completes its power-up test.
(See the terminal documentation for more information.)
2. Check the terminal settings. See the VAX 4000 Model 105A/106A Operator
Information manual for the list of correct settings.
3. Turn on the system unit by setting the on/off switch to the on ( | ) position.
Figure 1–8 Power Turn On

3
2

MLO-011873

! On/Off Switch (the on position ( | ) is shown)

Installation Procedure 1–9

Step 9: Checking the Power-Up Test Results
The power-up test can take several minutes to complete, depending on the
number of installed options and on which default settings you use.
1. If the power-up test results displayed on the screen are similar to the
results in Example 1–1, the system has passed the power-up test. Go to
step 9.
2. If the power-up test results displayed on the screen are not similar to the
results in Example 1–1, the system has not passed the power-up test. See
Example 1–2 for a typical failure.
Example 1–1 Successful Power-Up Test Screen
KA53-A VX.X, VMB 2.14

Performing normal system tests.
72..71..70..69..68..67..66..65..64..63..62..61..60..59..58..57..
56..55..54..53..52..51..50..49..48..47..46..45..44..43..42..41..
40..39..38..37..36..35..34..33..32..31..30..29..28..27..26..25..
24..23..22..21..20..19..18..17..16..15..14..13..12..11..10..09..
08..07..06..05..04..03..
Tests completed.
>>>

! Central Processing Unit (CPU) Name, Firmware Version Number, and
Virtual Memory Boot (VMB) Version Number

" Read-Only Memory (ROM) based diagnostics countdown
# Status Message
$ Console Prompt

1–10 Installation Procedure

If SIMM_OD is not present or not plugged in correctly, the system responds
with a display similar to the following example:
Example 1–2 Unsuccessful Power-Up Test Screen
KA53-A VX.X, VMB 2.14
Performing normal system tests.
72..71..70..69..68..67..66..65..64..63..62..

? Test_Subtest_DC_88 Loop_Subtest=05 Err_Type=FF DE_NO_Memory_present.lis
Vec=0000 Prev_Errs=0000 P1=E04EE04E P2=00000000 P3=00000000 P4=00001006
P5=00000000 P6=7F337F7F P7=00000000 P8=00000000 P9=FFFF0000 P10=2006270C
r0=00000008 r1=21018000 r2=E04EE04E r3=80000000 r4=01000000 r5=04000000
r6=00000002 r7=00000000 r8=00000000 r9=20140758 r10=FFFFFFFE r11=FFFFFFFF
dser=0000 cesr=00000000 icsr=01 pcsts=F800 pcctl=FC00 cctl=00000006
bcetsts=03E0 bcedsts=0400 cefsts=00007E80 nests=00 mmcdsr=01FFFE40
mesr=00000000
Error: SIMM Set 0 (0A,0B,0C,0D), SSR = E04E
SIMM_0A = 16MB
SIMM_0B = 16MB
SIMM_0C = 16MB

SIMM_0D = 00MB ??

Total of 0MB, 0 good pages, 0 bad pages, 0 reserved pages
Normal operation not possible.
>>>

! Error Message
" Error Summary showing SIMM "0D" is missing
# Status Message
Note
If a failure occurs, refer to VAX 4000 Model 105A/106A Troubleshooting
and Diagnostics Information manual.

Installation Procedure 1–11

Step 10: Connecting the System to a Network
If you want to connect the system to a network, see the VAX 4000
Model 105A/106A Operator Information manual.

Step 11: Connecting External Options to the System
If you want to connect external options to the system, see the VAX 4000
Model 105A/106A Operator Information manual.

Step 12: Booting the Operating System
The system is supplied with factory installed software (FIS) on the system
disk. Boot the operating system following the procedures in the VMS™ Factory
Installed Software User Guide.

1–12 Installation Procedure

Reader’s Comments

VAX 4000 Model 105A/106A Installation Information
EK–512AA–IN. B01

Your comments and suggestions help us improve the quality of our publications.
Thank you for your assistance.

I rate this manual’s:

Excellent

Good

Fair

Accuracy (product works as manual says)
Completeness (enough information)
Clarity (easy to understand)
Organization (structure of subject matter)
Figures (useful)
Examples (useful)
Index (ability to find topic)
Page layout (easy to find information)
I would like to see more/less
What I like best about this manual is
What I like least about this manual is

I found the following errors in this manual:
Page
Description

Additional comments or suggestions to improve this manual:

For software manuals, please indicate which version of the software you are using:

Name/Title

Dept.

Company

Date

Mailing Address
Phone

Poor

Do Not Tear – Fold Here and Tape
TM

BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 33 MAYNARD MASS.

POSTAGE WILL BE PAID BY ADDRESSEE

DIGITAL EQUIPMENT CORPORATION
Shared Engineering Services
MLO5–5/E76
2 THOMPSON STREET
MAYNARD, MA 01754-1716

Do Not Tear – Fold Here

No Postage
Necessary
If Mailed
in the
United States