Digital PDFs

EK-510AA-UP-A01

August 1993

42 pages

Original

0.7MB

Document:	MicroVAX 3100 Model 90 SCSI Upgrade Manual
Order Number:	EK-510AA-UP
Revision:	A01
Pages:	42
Original Filename:

OCR Text

MicroVAX 3100 Model 90
SCSI Upgrade Manual
Order Number: EK–510AA–UP. A01

August 1993

Digital Equipment Corporation
Maynard, Massachusetts

August 1993
Digital Equipment Corporation makes no representations that the use of its products in the
manner described in this publication will not infringe on existing or future patent rights, nor do
the descriptions contained in this publication imply the granting of licenses to make, use, or sell
equipment or software in accordance with the description.
MicroVAX, MicroVAX 3100, VAX, VAXserver, OpenVMS, and the DIGITAL logo are trademarks
of Digital Equipment Corporation.
All other trademarks and registered trademarks are the property of their respective holders.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case users will be required to correct the
interference at their own expense.
This document is available in hard copy only.

This document was prepared using VAX DOCUMENT, Version 2.1.

Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 Upgrading the MicroVAX 3100 Model 90 System
1.1
1.2
1.3
1.4

Overview of the Conversion Processes . . . . . . . . . . . . . . . . . . . . .
Unpacking the Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Firmware and Upgrading the Operating
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the SCSI Daughter Card . . . . . . . . . . . . . . . . . . . . . . .

1–1
1–2
1–3
1–4

A Conversion Forms
A.1
A.2
A.3

Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customer Administrative Services (CAS) District Offices . . . . . .

A–1
A–2
A–9

B Documentation and Ordering
B.1
B.2
B.3

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

B–1
B–1
B–2

Disconnecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Enclosure Cover . . . . . . . . . . . . . . . . . . . . . . .
Unscrewing the Drive Shelf Screws . . . . . . . . . . . . . . . . . . . .
Disconnecting the Internal Power Cables . . . . . . . . . . . . . . . .
Disconnecting the Internal SCSI Cable from the Mother
Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sliding the Drive Mounting Shelves Forward . . . . . . . . . . . .

1–4
1–5
1–6
1–7

Figures
1–1
1–2
1–3
1–4
1–5
1–6

1–8
1–9

iii

1–7
1–8
1–9
1–10
1–11
1–12
1–13
1–14
1–15

Lifting the Drive Mounting Shelves Upward . . . . . . . . . . . . .
Removing the Blank Cover from the Cutout . . . . . . . . . . . . .
Installing the New SCSI Cable . . . . . . . . . . . . . . . . . . . . . . .
Installing the SCSI Daughter Card . . . . . . . . . . . . . . . . . . . .
Connecting the New SCSI Cable to the Daughter Board . . . .
Aligning the Drive Mounting Shelves . . . . . . . . . . . . . . . . . .
Reinstalling the Drive Mounting Shelves . . . . . . . . . . . . . . . .
Securing the Drive Mounting Shelves . . . . . . . . . . . . . . . . . .
Connecting the Cables and Terminators . . . . . . . . . . . . . . . .

1–10
1–11
1–12
1–13
1–14
1–15
1–16
1–17
1–18

Contents of the KZDDA–AF Upgrade Kit . . . . . . . . . . . . . . .

1–3

Tables
1–1

Preface
This document describes how to upgrade a MicroVAX 3100 Model 90 system by
adding a SCSI card and port to support external SCSI devices.

Intended Audience
This document is intended for Digital Services personnel and licensed
self-maintenance customers.

Customer Responsibilities
Only qualified maintenance personnel (Digital Services representatives
or qualified self-maintenance customers) should perform the installation
procedure.
If you are not a qualified self-maintenance customer, call Digital Services to
schedule a system conversion. It is the customer’s responsibility to perform a
software backup before a Digital Services representative arrives at your site.
Appendix A contains forms that need to be completed by the Digital Services
representative and signed by both the customer and the Digital Services
representative.

Digital Services Responsibilities
Before arriving at the site, the Digital Services representative should contact
the customer to ensure that the customer’s software is backed up before
arriving at the site.
After installation of the upgrade kit, the Digital Services representative must
complete the forms in Appendix A and remove them from this document. The
forms must be signed by the customer and the Digital Services representative.

The following forms are in Appendix A:
•

Digital Services Worksheet

•

Installation Receipt–Customer Copy

•

Installation Receipt–Digital Services Copy

Organization
This document contains one chapter and two appendices:

•

Chapter 1 describes the upgrade conversion procedures in detail.

•

Appendix A contains forms and a list of the Customer Administrative
Services (CAS) district offices.

•

Appendix B is a list of related documents.

Conventions
The following conventions are used in this document:
Convention

Description

A lowercase italic x indicates the generic use of a letter. For
example, xxx indicates any combination of three alphabetic
characters.

italic type

Italic type emphasizes important information or indicates
variables. It is also used for the titles of manuals.

boldface type

Boldface type in examples indicates either user input or the first
instance of terms defined in the text.

A lowercase italic n indicates the generic use of a number.
For example, nnn indicates any combination of three numeric
characters.

nn nnn.nnn nn

A space character separates groups of 3 digits in numbers with 5
or more digits. For example, 10 000 equals ten thousand.

n.nn

A period in numbers indicates the decimal point. For example,
1.75 equals one and three-fourths.

MONOSPACE

Text displayed on the screen is shown in monospaced type.

radix indicators

The radix of a number is written as a word enclosed in
parentheses. For example, 23(decimal) or 34(hexadecimal).

UPPERCASE

A word in upper case indicates a command.

Note

A note contains information that is of special importance to the
user.

Caution

A caution contains information to prevent damage to the
equipment.

vii

1
Upgrading the MicroVAX 3100 Model 90
System
This chapter provides the procedures for upgrading a MicroVAX 3100 Model 90
system by adding a SCSI card and port to support external SCSI devices.

1.1 Overview of the Conversion Processes
The following tasks are required to upgrade a MicroVAX 3100 Model 90
system. To begin the actual conversion, turn to Section 1.2. The upgrade
includes installing a new SCSI cable, port, and a single SCSI daughter card.
1. Have the customer back up the system software.
2. Unpack and verify the conversion kit.
Note
The two steps that follow are not applicable if your MicroVAX 3100
Model 90 system already has Version 2.3 firmware and the OpenVMS
Version 5.5-2H4 software.

3. Upgrade the firmware to Version 2.3.
4. Upgrade the OpenVMS disk to Version 5.5-2H4.
5. Shut down the operating system and run the power-up diagnostics.
6. Turn off the system power and remove the power cord.
7. Remove the enclosure cover.
8. Remove the upper and lower drive mounting shelves.
9. Remove the blank cutout cover from the rear of the enclosure.
10. Install the new SCSI cable and connector in the enclosure.
11. Install the new SCSI daughter card onto the mother board.
Upgrading the MicroVAX 3100 Model 90 System 1–1

12. Reinstall the upper and lower drive mounting shelves in the system box,
simultaneously connecting the internal SCSI cable to the mother board.
13. Reinstall the enclosure cover.
14. Connect the power cable, signal cables and terminators to the system as
desired.
15. Turn on the system.
16. Have the customer reinstall system data (if necessary).
17. Fill out the appropriate paperwork (Appendix A).

1.2 Unpacking the Kit
Unpack the kit as follows:
1. Make sure there is no external damage to the shipping container, such as
dents, holes, or crushed corners.
2. Unpack the conversion kit and check its contents against the shipping
invoice. Table 1–1 lists the contents for the Model 90 upgrade kit,
KZDDA–AF. Other items may be present, but are not required for this
conversion.
Caution
Modules can be damaged by static discharge if an antistatic wrist strap
and antistatic mat are not used during handling. The wrist strap and
mat are in the antistatic kit in the Digital Services toolkit.

3. Unpack the SCSI daughter card and place it on a grounded antistatic mat.
4. If any item is missing or damaged:
•

Contact the customer’s sales representative.

•

Contact the customer’s delivery agent.

1–2 Upgrading the MicroVAX 3100 Model 90 System

Table 1–1 Contents of the KZDDA–AF Upgrade Kit
Description

Part Number

Quantity

SCSI terminator connector

12–30552–01

Cable assembly

17–02542–01

SCSI daughter card

54–23130–01

Sems screw

90–09643–00

SCSI upgrade manual

EK–510AA–UP

QA–001AA–UW

MV 3100/VAX 4000-100 fld

QZ–004AA–FW

Packing carton

99–08222–01

Plastic bag

99–06557–30

OpenVMS Version 5.5-2H4

1.3 Installing the Firmware and Upgrading the Operating
System
Before you install the hardware, you must install the firmware and upgrade
the OpenVMS operating system as follows:
1. Have the customer back up the system software before the Digital Services
representative arrives. It is the customer’s responsibility to back up the
system software.
2. Power up the system and run diagnostics to verify system operation.
3. Upgrade the firmware using the Updating KA50/KA52 CPU Firmware
document which is included in the QZ–004AA–FW kit.1
4. Upgrade the OpenVMS disk to Version 5.5-2H4.1
5. Shut down the operating system in the proper manner.
6. Turn off the system power before you install the kit.

If your MicroVAX 3100 Model 90 system already has Version 2.3 firmware and
OpenVMS Version 5.5-2H4 software, it is not necessary to upgrade the firmware or
the OpenVMS software.

Upgrading the MicroVAX 3100 Model 90 System 1–3

1.4 Installing the SCSI Daughter Card
Follow this procedure to install the new daughter card and related hardware.
1. Disconnect the power cord (Figure 1–1).
Figure 1–1 Disconnecting the Power Cord

3
2

MLO-010959

Power cord

1–4 Upgrading the MicroVAX 3100 Model 90 System

2. Remove the enclosure cover by removing the two screws at the rear of the
system box and sliding the cover forward (Figure 1–2).
Figure 1–2 Removing the Enclosure Cover

3
2

1
MLO-010960

Screws
Enclosure cover

Upgrading the MicroVAX 3100 Model 90 System 1–5

3. Remove the upper and lower drive mounting shelves together as a
single unit; it is not necessary to disassemble the shelves themselves
(Figure 1–3).
a. Unscrew all six screws from the shelves, leaving the topmost captive
screw until last for support.
b. Leave the captive screws in position and save the Phillips screws for
reinstallation of the shelves.
Figure 1–3 Unscrewing the Drive Shelf Screws

3
2

MLO-010961

Topmost captive screw
Other captive screws

1–6 Upgrading the MicroVAX 3100 Model 90 System

Phillips screws

4. Disconnect the internal power cables from the power supply (Figure 1–4).
Figure 1–4 Disconnecting the Internal Power Cables

MLO-010803

Internal power cables

Upgrading the MicroVAX 3100 Model 90 System 1–7

5. Disconnect the internal SCSI cable from the mother board (Figure 1–5).
a. Release the memory module nearest the internal SCSI connector by
pressing the tabs on each end, and tip it forward.
b. Disconnect the internal SCSI cable from its connector on the mother
board.
Figure 1–5 Disconnecting the Internal SCSI Cable from the Mother Board
1

MLO-010805

Releasing the memory module and tipping it forward
Internal SCSI cable

1–8 Upgrading the MicroVAX 3100 Model 90 System

6. Remove the shelves as one unit by sliding them forward (Figure 1–6)
and lifting them up and away from the enclosure (Figure 1–7). Leave the
memory module tipped forward until the shelves are reinstalled.
Figure 1–6 Sliding the Drive Mounting Shelves Forward
1

MLO-010806

Drive mounting shelves

Upgrading the MicroVAX 3100 Model 90 System 1–9

Figure 1–7 Lifting the Drive Mounting Shelves Upward

MLO-010962

1–10 Upgrading the MicroVAX 3100 Model 90 System

7. To remove the blank cover from the cutout on the rear of the enclosure
where the new SCSI connector will be installed, push up on the bottom of
the cover while simultaneously pulling it out (Figure 1–8).
Figure 1–8 Removing the Blank Cover from the Cutout
1

MLO-010963

Blank cover
Cutout

Upgrading the MicroVAX 3100 Model 90 System 1–11

8. Install the SCSI in/out cable (17–02542–01) included in the upgrade kit
into the external cutout (Figure 1–9).
Figure 1–9 Installing the New SCSI Cable
1

3
2

MLO-010964

New SCSI cable connector
Phillips screw
Washer

1–12 Upgrading the MicroVAX 3100 Model 90 System

9. Install the SCSI daughter card onto the mother board (Figure 1–10). Align
the new card on the standoff so that it is positioned above the mother
board connector, then gently seat it onto the connector and the standoff.
Figure 1–10 Installing the SCSI Daughter Card
1

3
2
MLO-010965

Daughter card
Standoff
Mother board connector

Upgrading the MicroVAX 3100 Model 90 System 1–13

10. Run the new SCSI in/out cable (17–02542–01) between the rows of memory
modules and connect it to the rear connector slot on the new SCSI daughter
board (Figure 1–11).
Figure 1–11 Connecting the New SCSI Cable to the Daughter Board
1
2

MLO-010966

New SCSI cable
Connector slot on the daughter board

1–14 Upgrading the MicroVAX 3100 Model 90 System

11. Reinstall the upper and lower drive mounting shelves in the system
box, simultaneously connecting the internal SCSI cable (17–03588–01 or
17–02943–01) to the mother board.
a. Position the shelves by lining up the bracket tabs, but do not slide
them rearward yet (Figure 1–12).
Figure 1–12 Aligning the Drive Mounting Shelves

1
MLO-010967

Bracket tabs

Upgrading the MicroVAX 3100 Model 90 System 1–15

b. Connect the internal SCSI cable to its connector on the mother board.
(The memory module nearest the internal SCSI connector should
already be tipped forward; if it is not, see Figure 1–5.)
c.

Snap the memory module back into its upright position.

d. Slide the shelves down and rearward so that the holes on the bracket
tabs line up with their cutouts.
Figure 1–13 Reinstalling the Drive Mounting Shelves
2

MLO-010829

Internal SCSI cable

1–16 Upgrading the MicroVAX 3100 Model 90 System

Snapping the memory module upright

Tighten the shelves in place using the six screws which held them in
originally (Figure 1–14).
1. Tighten the topmost captive screw first to ensure that the shelves
do not fall and damage components underneath.
2. Tighten the remaining captive screws.
3. Replace and tighten the Phillips screws.

Figure 1–14 Securing the Drive Mounting Shelves

3
2

MLO-010968

Topmost captive screw

Phillips screws

Other captive screws

Upgrading the MicroVAX 3100 Model 90 System 1–17

12. Reconnect the power cables (Figure 1–4).
13. Reinstall the enclosure cover (Figure 1–2).
14. Connect the cables and terminators to the SCSI connectors on the rear of
the enclosure as desired (Figure 1–15).
Figure 1–15 Connecting the Cables and Terminators

3
2

MLO-010969

SCSI terminator
15. Turn on the system.
16. Have the customer reinstall the system data (if necessary).
17. Fill out the appropriate paperwork (Appendix A).

1–18 Upgrading the MicroVAX 3100 Model 90 System

A
Conversion Forms
The following forms must be completed to ensure that both the customer’s and
Digital’s records are up to date.
For locations outside the United States, contact the local Digital Equipment
Corporation office for destination instructions.

A.1 Procedures
Fill out the forms as follows:
1. Obtain the serial number of the system being converted. Customer
Administrative Services (CAS) cannot process the order without this serial
number.
2. Ensure that the serial number is on the purchase order.
3. Issue a hardcopy quotation to the customer; refer to the serial number.
4. Complete the Digital Services Worksheet in Section A.2. It documents the
work you performed.
Return the worksheet to your contract administrator at the branch office.
5. Contact your local Digital CAS office to obtain information for the
Installation Receipt. Section A.3 lists the CAS district offices and their
phone numbers.
6. Complete both copies of the Installation Receipt.
The first copy is the customer’s receipt. It shows that the installation was
completed and that Digital Services contacted CAS.
Return the second copy to Digital Services.

Conversion Forms A–1

A.2 Forms
This section contains the following forms:
•

Digital Services Worksheet

•

Installation Receipt—Customer Copy

•

Installation Receipt—Digital Services Copy

A–2 Conversion Forms

Digital Services Worksheet
This form acts as a verification of the work performed on the system and as a
check on the procedures used. Please fill out this form and return it to your
Contract Administrator for updating the customer’s contract.
Customer:
Previous System Model Number:
Previous System Serial Number:

New System Name:
New System Model Number:
New System Serial Number:
New Daughter Card Serial Number:
Comments:

Conversion Forms A–3

A–4 Conversion Forms

Installation Receipt—Customer Copy
For the upgrade of MicroVAX 3100 Model 90 SCSI configuration.
This form acts as a customer receipt and as verification for Digital Services
that the dual SCSI card upgrade kit was installed.
Digital Services:

Complete both copies of this form. Give a copy to the customer and
a copy to the local CAS office for filing with customer documents.

Customer:

Keep this copy as your record of installation by Digital Equipment
Corporation.

Name of CAS representative:
Branch Office:
Digital Order Number:
New System Serial Number:
New Daughter Card Serial Number:
Installation was performed on this date:
Customer Name:

Phone Number:

Customer Signature:
Digital Services Representative Signature:

Conversion Forms A–5

A–6 Conversion Forms

Installation Receipt—Digital Services Copy
For the upgrade of MicroVAX 3100 Model 90 to a SCSI configuration.
This form acts as a verification for Digital Services that the SCSI daughter
card upgrade kit was installed.
Digital Services:

Complete both copies of this form. Give a copy to the customer and
a copy to the local CAS office for filing with customer documents.

Name of CAS representative:
Branch Office:
Digital Order Number:
New System Serial Number:
New Daughter Card Serial Number:
Installation was performed on this date:
Customer Name:

Phone Number:

Customer Signature:
Digital Services Representative Signature:

Conversion Forms A–7

A–8 Conversion Forms

A.3 Customer Administrative Services (CAS) District Offices
Name, Location

Phone Number

Allegheny District, Pittsburgh, PA

(412) 244–7410

Carolinas District, Columbia, SC

(803) 798–6477

Chicago District, Chicago, IL

(312) 806–2478

Connecticut District, Meriden, CT

(203) 634–5325

CSS District, Nashua, NH

(603) 884–6549

DECdirect District, Nashua, NH

(603) 884–9115

Florida District, Tampa, FL

(813) 882–6822

Greater Boston District, Waltham, MA

(617) 895–5455

Great Lakes District, Detroit, MI

(313) 344–2285

Los Angeles District, Culver City, CA

(213) 417–4232

Midsouth District, Memphis, TN

(901) 761–6712

New Jersey Commercial District, Piscataway, NJ

(201) 562–4728

New Jersey Financial District, New York, NY

(212) 714–2648

New York Financial District, New York, NY

(212) 714–2648

New York Suburban District, Tarrytown, NY

(914) 524–5284

North Central District, Minneapolis, MN

(612) 851–2225

North Texas/Oklahoma District, Dallas, TX

(214) 404–6135

Northwest District, Bellevue, WA

(206) 462–2540

Ohio Valley District, Cincinnati, OH

(513) 984–7739

Philadelphia District, Blue Bell, PA

(215) 834–4115

Rocky Mountain District, Englewood, CO

(303) 649–3073

Santa Clara District, Santa Clara, CA

(408) 496–4274

Southeast District, Atlanta, GA

(404) 257–2282

Southern California District, Costa Mesa, CA

(714) 850–7606

South Texas District, Houston, TX

(713) 953–3918

Southwest District, Tempe, AZ

(602) 894–4747

Upstate New York District, Rochester, NY

(716) 385–7152

Conversion Forms A–9

Name, Location

Phone Number

U.S. Distribution/Sales District, Marlboro, MA

(508) 480–4259

Virginia District, Landover, MD

(301) 306–2566

Washington DC District, Landover, MD

(301) 459–2890

Washington DC District, FDA Landover, MD

(301) 459–2292

A–10 Conversion Forms

B
Documentation and Ordering
B.1 Introduction
This appendix provides information about related documentation and ordering.

B.2 Related Documentation
You can order the following documents from Digital:
VAX 3100 Model 90 Documentation
•

MicroVAX 3100 Model 90 Cover Letter (EK–A0608–CL)

•

MicroVAX 3100 Model 90 Installation Information (EK–A0604–IN)

•

MicroVAX 3100 Model 90 Operator Information (EK–A0605–OP)

•

MicroVAX 3100 Model 90 Customer Technical Information (EK–A0606–TM)

•

MicroVAX 3100 Model 90 Troubleshooting and Diagnostics Information
(EK–A0607–TI)

•

Updating KA50/KA52 CPU Firmware (EK–VX4FW–UP)

OpenVMS Factory Installed Software Documentation
•

OpenVMS Factory Installed Software User Information (EK–A0377–UG)

Documentation and Ordering B–1

B.3 Ordering Information
You can order options and documentation by mail, phone, or electronically.
Need Help?
If you need help deciding which documentation best meets your needs, please
call 800–DIGITAL (800–344–4825) and press 2 for technical assistance.
Electronic Orders
To place an order through your account at the Electronic Store, dial
800–234–1998, using a modem set to 2400 or 9600 baud. You must use a
VT terminal or terminal emulator set at 8 bits, no parity. If you need help, call
800–DIGITAL (800–344–4825) and ask for an Electronic Store specialist.
Telephone or Direct Mail Orders
You can order documentation by phone or direct mail.
If You Are
From . . .

Call . . .

Or Write . . .

U.S.A.

DECdirect
Phone: 800–DIGITAL
(800–344–4825)
FAX: (603) 884–5597

Digital Equipment Corporation
P.O. Box CS2008
Nashua, NH 03061

Puerto Rico

Phone: (809) 781–0505
FAX: (809) 749–8377

Digital Equipment Caribbean, Inc.
3 Digital Plaza, 1st Street
Suite 200
Metro Office Park
San Juan, Puerto Rico 00920

Canada

Phone: 800–267–6215
FAX: (613) 592–1946

Digital Equipment of Canada Ltd.
100 Herzberg Road
Kanata, Ontario, Canada K2K 2A6
Attn: DECdirect Sales

International

—

Local Digital subsidiary or approved
distributor

B–2 Documentation and Ordering

Digital Personnel
You can order documentation by electronic mail. Contact the following
organizations for instructions:
If You Need . . .

Call . . .

Contact . . .

Software
documentation1

DTN: 241–3023
(508) 874–3023

Software Supply Business
Digital Equipment Corporation
1 Digital Drive
Westminster, MA 01473

Hardware
documentation

DTN: 234–4325
(508) 351–4325
FAX: (508) 351–4467

Publishing & Circulation Services
Digital Equipment Corporation
NRO2-2/I5
444 Whitney Street
Northboro, MA 01532

1 Call to request an Internal Software Order Form (EN–01740–07).

Documentation and Ordering B–3

Reader’s Comments

MicroVAX 3100 Model 90
SCSI Upgrade Manual
EK–510AA–UP. A01

Your comments and suggestions help us improve the quality of our publications.

Please rate the manual in the
following categories:

Excellent

Good

Accuracy (product works as described)
Completeness (enough information)
Clarity (easy to understand)
Organization (structure of subject matter)
Figures (useful)
Examples (useful)
Table of contents (ability to find topic)
Index (ability to find topic)
Page design (overall appearance)
Print quality
What I like best about this manual:
What I like least about this manual:
Additional comments or suggestions:

I found the following errors in this manual:
Page

Description

For which tasks did you use this manual?
Installation
Maintenance
Marketing
Operation/Use
Name/Title
Company
Address

Programming
System Management
Training
Other (please specify)

Fair

Poor

Do Not Tear – Fold Here and Tape
NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES

BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 33 MAYNARD MASS.

POSTAGE WILL BE PAID BY ADDRESSEE

DIGITAL EQUIPMENT CORPORATION
INFORMATION DESIGN AND CONSULTING
PKO3–1/D30
129 PARKER STREET
MAYNARD, MA 01754–9975

Do Not Tear – Fold Here and Tape