Digital PDFs

EK-424AA-TS-001

May 1990

110 pages

Original

1.4MB

Document:	Microvax 3100 VAXserver Options Installation Guide
Order Number:	EK-424AA-TS
Revision:	001
Pages:	110
Original Filename:

OCR Text

MicroVAX 3100 and VAXserver 3100
Options Installation Guide
Order Number EK-424AA-TS-001

Digital Equipment Corporation

September, 1990
The information in this document is subject to change without notice and should not
be construed as a commitment by Digital Equipment Corporation. Digital Equipment
Corporation assumes no responsibility for any errors that may appear in this document.
The software described in this document is furnished under a license and may be used or
copied only in accordance with the terms of such license.
No responsibility is assumed for the use or reliability of software on equipment that is not
supplied by Digital Equipment Corporation or its affiliated companies.
Restricted Rights: Use, duplication, or disclosure by the U. S. Government is subject to
restrictions as set forth in subparagraph ( c ) ( 1 ) ( ii ) of the Rights in Technical Data and
Computer Software clause at DFARS 252.227–7013.
Copyright © Digital Equipment Corporation 1990
All Rights Reserved.
Printed in U.S.A.
FCC NOTICE: The equipment described in this manual generates, uses, and may emit
radio frequency energy. The equipment has been type tested and found to comply with
the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC
Rules, which are designed to provide reasonable protection against such radio frequency
interference when operated in a commercial environment. Operation of this equipment in
a residential area may cause interference, in which case the user at his own expense may
be required to take measures to correct the interference.
The following are trademarks of Digital Equipment Corporation:
BASEWAY
BI Bus
DEC
DEC/MAP
DECmate
DECnet
DECUS
DECwriter
DIBOL
EDCS
FMS

MASSBUS
MicroPDP–11
Micro/RSTS
Micro/RSX
MicroVAX II
PDP
P/OS
Professional
Q–bus
Rainbow
RSTS

RSX
RT
UNIBUS
VAX
VAXcluster
VAXstation II
VAXstation II/GPX
VMS
VT
Work Processor

This document was prepared and published by Educational Services Development and
Publishing, Digital Equipment Corporation.

About This Manual
This manual describes how to install options for the MicroVAX 3100
and VAXserver 3100 systems. The label on the rear of the system box
indicates the system you are working on (MicroVAX or VAXserver).

Organization
The manual is divided into chapters according to the options available for
the systems:
General Information, contains an overview of the systems and an
option list.
Model 10 MicroVAX/VAXserver 3100, contains the disassembly and
assembly procedures for the Model 10 MicroVAX 3100 or VAXserver 3100
System.
Model 20 MicroVAX/VAXserver 3100, contains the disassembly and
assembly procedures for the Model 20 MicroVAX 3100 or VAXserver 3100
System.
Memory, contains installation procedures for the optional memory
modules available for the MicroVAX/VAXserver 3100 systems.
Communications, contains installation procedures for the
communications option, available for the MicroVAX/VAXserver 3100
systems.
It also provides instructions for the installation of the DSH32-Yx second
synchronous line driver/receiver module and associated cabling.
Disks, contains SCSI Bus configuration rules, system configuration rules,
and available add-on disk options for the MicroVAX 3100 and VAXserver
3100 system.
RX23 Disk Drive, provides instructions for installing an RX23 option
into a Model 10 or Model 20 MicroVAX 3100 or VAXserer 3100 system.
RZ23 Disk Drive, provides instructions for installing an RZ23 option
into a MicroVAX 3100 or VAXserver 3100 system.
v

vi About This Manual

RZ24 Disk Drive, provides instructions for installing an RZ24 option
into a MicroVAX 3100 or VAXserver 3100 system.
RZ55 (in BA40 Disk Expansion Box), provides instructions for
connecting the RZ55/BA40 Disk expansion to the MicroVAX 3100 or
VAXserver 3100 system.
SZ12x (in BA42 Disk Expansion Box), refers to the installation, and
upgrade of the SZ12x (BA42) storage expansion box. It includes details
for setting up and using the storage expansion box for the first time, and
information on adding a storage device to the storage expansion box.
TZ30 Tape Drive, describes the installation procedure for the TZ30 tape
drive option for the MicroVAX 3100 and VAXserver 3100 sytems.
TK50Z Tape Drive, provides instruction for installing the TK50Z
expansion box in the MicroVAX 3100 and VAXserver 3100 systems.
CD ROM, contains installation procedures for the CDROM options
available for the MicroVAX/VAXserver 3100 systems.
Appendix A, contains a table of diagnostic test commands and utility
commands.
Appendix B, contains hexadecimal memory codes.
Appendix C, contains examples of the "SHOW DEVICE" command.

Intended Audience
This document is for Digital Customer Services personnel and selfmaintenance customers only.

Tools and Equipment
You will need the following tools to service the MicroVAX 3100 and
VAXserver 3100 systems:
•

Wrist strap and antistatic mat (included in the Customer Service
antistatic kit), part number 29-26246-00.

•

Customer Service tool box kit, part number 29-27339-01.

About This Manual vii

Conventions
This document uses the following conventions:
•

Warning Provides information to prevent personal injury. Read these
carefully.

•

Caution Provides information to prevent damage to the equipment or
software. Read these carefully.

•

Note Provides general information to be aware of.

•

Important Provides information that must be observed.

Related Documents
The following document list is a guide to order documents from Digital.
These documents will provide more detailed general and technical
information for the MicroVAX/VAXserver 3100 systems and options.
Document

Order Number

MicroVAX 3100 and VAXserver 3100
Owners Manual

EK-A0371-OM

MicroVAX 3100 and VAXserver 3100
Maintenance Guide

EK-A0372-MG

MicroVAX 3100 and VAXserver 3100
Planning and Preparation

EK-A0373-PC

MicroVAX 3100 and VAXserver 3100
Illustrated Parts Breakdown

EK-A0372-IP

MicroVAX 3100 and VAXserver 3100
Maintenance Advisory

EK-M3100-MA

Storage Expansion Box

EK-SEBOX-IN

RZ56 Disk Drive Subsystem Manual

EK-RZ56D-SV

RZ Disk Drive Susbsystem Pocket Service
Guide

EK-RZXXD-PS
EK-RZ57D-SV

RZ22, RZ23, RZ24 Service Manual

EK-RZ234-SV

viii About This Manual

Ordering Information for Digital personnel
Digital Equipment Corporation
44 Whitney Street
Northboro, MA 01532
Attn: Publishing and Circulation Services (NRO03/W3)
Order Processing Section

General Information
Product Overview
The MicroVAX 3100 series include the MicroVAX 3100 and the VAXserver
3100 systems. The MicroVAX 3100 system is a desktop VAX computer
which supports a maximum of eleven users. The VAXserver 3100 system
is a desktop server designed to provide operating system services for
dedicated applications or devices.
The MicroVAX/VAXserver 3100 series is available in a Model 10 and a
Model 20 version.
The Model 20 provides a larger storage capacity with a six-inch-high
enclosure and including upper and lower drive mounting plates.
The Model 10 provides a four-inch-high enclosure, with only the lower
drive mounting plate.
Both systems can be used either independently or in a work group with
other VAX systems.

General Information GEN–1

Options List
The following table lists the options that may be used with the
MicroVAX/VAXserver 3100 series:
Options list:
Option

Size

MS42-AB

4 megabyte expansion memory

MS42-KA

8 megabyte expansion memory

MS42-BA

12 megabyte expansion memory

MS42-CA

16 megabyte expansion memory

DSH32-B

8 Asyncronous/1 Syncronous
Communications module

RRD40

5 1/4" Half-height CD-ROM 600
MB

RX23

3 1/2" Half-height Floppy Disk 1.4
MB

RZ23

3 1/2" Half-height Disk 104 MB

RZ24

3 1/2" Half-height Disk 209 MB

RZ55

5 1/4" Full-height Disk 332 MB

RZ56

5 1/4" Full-height Disk 665 MB

RZ57

5 1/4" Full-height Disk 1.2 GB

TK50

5 1/4" Full-height Tape 95 MB

TZ30

5 1/4" Half-height Tape 95 MB

GEN–2 General Information

Model 10 MicroVAX/VAXserver
3100
Disassembling the Model 10 MicroVAX 3100 or
VAXserver 3100 System
To enable option(s) installation, disassemble the Model 10 MicroVAX 3100
or VAXserver 3100 system.
CAUTION
Wear an anti-electrostatic wrist strap and use an anti-electrostatic
mat when installing or replacing field replaceable units (FRUs).
To disassemble the Model 10 MicroVAX 3100 or VAXserver 3100
system do the following:
1. Bring down the Operating System Software and halt the system.
2. Turn off the power to the system box and any expansion boxes.
3. Disconnect all cables and loopbacks connected to the system unit.
Place any expansion boxes off to the side, away from the system unit.
4. Loosen the two captive screws on the rear bezel of the system box
(Refer to Figure M10–1).

Model 10 M10–1

Cover Screw Locations

MLO-003278

Figure M10–1

Captive Screw Locations (Model 10)

5. Slide the top cover forward and up, away from the system box.
6. Remove the SCSI "B" external port connector from the rear panel by
removing the two mounting screws on the rear of the system unit
(Refer to Figure M10–2).

M10–2

Model 10

ASYNC
PO RT

SYNC
PORT

EXTERNAL
SCSI -B PORT

2 SCREWS

ON/ OFF
SWI TCH

THICKW IRE
PO RT

THINW IRE
PO RT

TERMINAL
LINES

MODEM
PORT
LJ-00040-TI0

Figure M10–2

Removing the SCSI "B" External Port Connector

7. Disconnect the DC power harness plug from J1 on the H7821 power
supply (Refer to Figure M10–3).

Model 10 M10–3

Unused

Distribution
Board

H7 8 2 1
Power
Supply

SCSI-A

DSH32-B
System Module

RZ 2x

SCSI-B

To FDI Board
for RX23
Option

T Z 30, R X23,
or R Z 2x

Additional
Power
Connector
for RX23
Drive

Unused
Drive Mounting Panel

LJ-00041-TI0

Figure M10–3

DC Power Connector (Model 10)

8. Disconnect the system module cable from the distribution module
(Refer to Figure M10–4).

M10–4

Model 10

SCSI-B Cable
DSH32-B Communications
Module Cable

Captive Screws

SCSI-A Cable
System Module Cable

MLO-003286

Figure M10–4

Distribuiton Module Cables

9. Disconnect the DSH32 module cable (if applicable) from the
distribution module (Refer to Figure M10–4).
10. Loosen the four captive screws on the top, and the 3 panhead
screws located on the right side of the drive mounting shelf (Refer
to Figure M10–5).

Model 10 M10–5

Captive Screw (2)

Captive Screws (2)

Panhead Screws
(3 Loosened)
LJ-00042-TI0

Figure M10–5

Drive Mounting Panel (Model 10)

11. Slide the drive mounting shelf forward, then lift the shelf from the
system unit, and gently set it aside.
NOTE
At this point, the system unit is disassembled enough to allow you
to install any and all of the various options.
For specific option installation procedures refer to the
appropriate section.

M10–6

Model 10

Assembling the Model 10 MicroVAX 3100 or
VAXserver 3100 System
This section describes how to re-assemble the Model 10 system after the
option installation has been completed.
CAUTION
Wear an anti-electrostaic writst strap and use an anti-electrostatic
mat when installing or replacing field replaceable units (FRUs).
To assemble the Model 10 MicroVAX 3100 or VAXserver 3100
system do the following:
1. Set the drive mounting shelf in place and tighten the 4 captive screws
and 3 panhead screws (Refer to Figure M10–5).
2. Connect the DSH32 module cable (if applicable) to the distribution
module (Refer to Figure M10–4).
3. Connect the system module cable to the distribution module (Refer to
Figure M10–4).
4. Connect the DC power harness plug J1 to the H7821 power supply
(Refer to Figure M10–3).
5. Install the SCSI "B" external port connector to the rear panel by
installing the two mounting screws on the rear of the system unit
(Refer to Figure M10–2).
6. Ensure the appropriate data and power cables are connected to each
storage device (Refer to Figure M10–6).

Model 10 M10–7

Unused

Distribution
Board

H7821
Power
Supply

SCSI-B
SCSI-A

DSH32-B
System Module

To FDI Board
for RX23
Option

TZ30, RX23,
or RZ2x

RZ2x

Additional
Power
Connector
for RX23
Drive

Unused
Drive Mounting Panel

Distribution
Board

SCSI-B

H7821

SCSI-A

DSH32-B

Power
Supply

System Module
To FDI Board
for RX23
Option

RZ2x

RX23 or
RZ2x

RZ2x

Additional
Power
Connector
for RX23
Drive

Drive Mounting Panel
LJ-00043-TI0

Figure M10–6
M10–8

Model 10

Storage Device Positioning and Cabling

7. Place the top cover on the system box and secure it in place
and tighten the two captive screws on the rear bezel (Refer to
Figure M10–1).
8. Connect all cables, loopback connectors, and expansion boxes which
were previously disconnected from the system unit.
9. Power up the expansion box(es) before powering up the system box (if
applicable).
10. Power up the system box and ensure a successful completion of the
self-test.
11. Refer to the section on the newly installed option for console test
commands.
12. Bring up the operating system software to verify the system
functionality.

Model 10 M10–9

Model 20 MicroVAX/VAXserver
3100
Disassembling Model 20 MicroVAX 3100 or
VAXserver 3100 System
This section describes how to disassemble the Model 20, MicroVAX 3100
or VAXserver 3100 system in order to enable option(s) installation.
CAUTION
Wear an anti-electrostatic wrist strap and use an anti-electrostatic
mat when installing or replacing field replaceable units (FRUs).
1. Bring down the Operating System Software and halt the system.
2. Turn off the power to the system box and any expansion boxes.
3. Disconnect all cables and loopbacks connected to the system unit and
place any expansion boxes off to the side and away from the system
unit.
4. Loosen the two captive screws on the rear bezel of the system box
(Refer to Figure M20–1).

Model 20 M20–1

Cover Screw Locations

MLO-002946

Figure M20–1

Captive Screw Location (Model 20)

5. Slide the top cover forward and up off the system box.
6. Disconnect the SCSI bus cables from the drives on the upper drive
mounting shelf (Refer to Figure M20–2).

M20–2

Model 20

Distribution Board
SCSI-B
SCSI-A
Adapter (TZ30 Only)

SCSI-B Connector

J2
J1

H782 2
Power
Supply

RX23 or
RZ2x

TZ30 Tape Drive,
RZ2x Disk Drive,
or RX23 Diskette
Drive

RZ2x
Disk
Drive

Lower Drive
Mounting Panel

Upper Drive
Mounting Panel

RZ2x
Disk
Drive

Upper Drive Panel Power
Lower Drive Panel Power
Data
LJ-00044-TI0

Figure M20–2

Drive Mounting Panel Power and Signal Cabling

Model 20 M20–3

IMPORTANT
You must note which cables connect to which drives when you
disconnect them.
Write the type of drive and its position on a piece of tape and
wrap the tape around the connector before you disconnect it.
This will help you when you reinstall the drives.
7. Disconnect the power harness plugs from connectors J1 and J2 of the
H7822 power supply (Refer to Figure M20–2).
8. Unscrew the four captive screws on the upper drive mounting shelf
(Refer to Figure M20–3).

M20–4

Model 20

Captive Screws (2)

Upper Drive
Mounting Panel

Captive
Screws (2)
MLO-002957

Figure M20–3

Upper Drive Mounting Panel (Model 20)

9. Lift the upper drive mounting shelf from the system unit and gently
set it aside.

Model 20 M20–5

IMPORTANT
Stop here if you install additional half-height hard disk on the
upper drive shelf.
10. Remove the SCSI "B" external port connector from the rear panel by
removing the two mounting screws on the rear of the system unit
(Refer to Figure M20–4).

ASYNC
PORT

S YN C
P O R TS

E X TE R N A L
S C S I - B P OR T

2 S C R E WS

ON / OFF
S WI TC H

THICKWIRE
PORT

THINWIRE
PORT

TE R M I N A L
LI N E S

M OD E M
P OR T
LJ-00045-TI0

Figure M20–4

Removing the SCSI "B" External Port Connector

11. Disconnect the system module cable from the distribution module
(Refer to Figure M20–5).

M20–6

Model 20

SCSI-B Cable
DSH32-B Communications
Module Cable

Captive Screws

SCSI-A Cable
System Module Cable

MLO-003285

Figure M20–5

Distribution Module Cables

12. Disconnect the DSH32 module cable (if applicable) from the
distribution module (Refer to Figure M20–5).
13. On the lower drive mounting shelf, loosen the four captive screws
on the top, and the 3 panhead screws located on the right-hand side
(Refer to Figure M20–6).

Model 20 M20–7

Captive Screw (1)

Captive Screws (3)

Lower Drive Mounting Panel

Panhead Screws
(3 Loosened)
MLO-002956

Figure M20–6

Lower Drive Mounting Shelf

14. Slide the lower drive mounting shelf forward, then lift the shelf from
the system unit and gently set it aside.
NOTE
At this point, the system unit is disassembled enough to allow you
to install any and all of the various options.
For specific option installation procedures refer to the
appropriate section.

M20–8

Model 20

Assembling the Model 20 MicroVAX 3100 or
VAXserver 3100 System
This section describes how to re-assemble the Model 20 system after the
option installation has been completed.

CAUTION
Wear an anti-electrostatic wrist strap and use an anti-electrostatic
mat when installing or replacing field replaceable units (FRUs).
1. Set the lower drive mounting shelf in place and tighten the four
captive screws and the 3 panhead screws located on the right-hand
side (Refer to Figure M20–6).
2. Connect the DSH32 module cable (if applicable) to the distribution
module (Refer to Figure M20–5).
3. Connect the system module cable to the distribution module (Refer to
Figure M20–5).
4. Install the SCSI "B" external port connector to the rear panel by
installing the two mounting screws on the rear of the system unit
(Refer to Figure M20–4).
5. Ensure the SCSI data cables and power cables are connected to each
storage device (Refer to Figure M20–2).
6. Place the upper drive mounting shelf in place and tighten the four
captive screws (Refer to Figure M20–3).
7. Connect the DC power harness plugs to connectors J1 and J2 of the
H7822 power supply (Refer to Figure M20–2).
8. Connect the SCSI bus cables to the drives on the upper drive
mounting shelf (Refer to Figure M20–2).
9. Place the top cover on the system box and secure it in place by
tightening the two captive screws (Refer to Figure M20–1).
10. Connect all cables, loopback connectors, and expansion boxes which
were previously disconnected from the system unit.
11. Power up the expansion box(es) before powering up the system box (if
applicable).

Model 20 M20–9

12. Power up the system box and ensure a successful completion of the
self-test.
13. Refer to the section on the newly installed option for console
commands.
14. Bring up the operating system software to verify the system
functionality.

M20–10

Model 20

Memory
MicroVAX 3100 or VAXserver 3100 Memory
Configuration
The MicroVAX 3100/VAXserver 3100 memory can be configured to equal
totals of 8, 12, 16, 20, 24 and 32 megabyte configurations. This is
accomplished by the addition of either one or two memory expansion
modules to the system module. Note, the system module contains 4
megabyte of resident memory. Refer to the information below for memory
expansion guidelines.
Rules:
•

A maximum of two memory modules can be added per system,
however, each variant may be selected only once.

•

The MS42-KA (8 MB) & MS42-CA (16 MB) may not be configured
together.

•

The MS42-AB (4 MB) & MS42-BA (12 MB) may not be configured
together.

Memory Module Installation
This section describes:
•

single memory module installation without an expansion memory
currently installed

•

single memory module installation with an expansion memory
currently installed

•

dual memory module installation

Memory MEM–1

Single Memory Module Installation Without
Expansion Memory Installed
1. Refer to either the Model 10 or Model 20 chapter for the system
disassembly procedure.
2. Align the expansion memory module connector with the system
module expansion memory connector (Refer to Figure MEM–1).
3. Press down on the expansion memory until this module is fully seated.
4. Press down on the outer edge of the expansion memory to secure it
onto the standoff tabs.

Memory Module

LJ-00046-TI0

Figure MEM–1

Memory Module Removal

5. Refer to either the Model 10 or Model 20 chapter for the system
reassembly procedure.

MEM–2

Memory

6. After power up and a successful completion of the self-tests, verify
the new memory configuration by entering the SHOW MEMORY
command at the console prompt (>>>).
7. For memory configuration equivalent values refer to Appendix B.

Single Memory Module Installation With Expansion
Memory Installed
1. Refer to either the Model 10 or Model 20 chapter for the system
disassembly procedure.
2. Release the memory module from the standoffs and separate this
module from the system module.
3. Align the memory module just removed with the new memory module.

8/16 Mbyte Memory Module

"E" Clips
(2 Places)

4/12 Mbyte Memory Module
System Module
LJ-00047-TI0

Figure MEM–2

Memory Module Connections

Memory MEM–3

4. Press modules together until both modules are fully seated (Refer to
Figure MEM–2.
5. Install the "E" clips onto the expansion memories (Refer to
Figure MEM–2).
6. Remove the two taller standoffs which supported the expansion
memory by bending them over until they snap off. Discard the
standoffs (Refer to Figure MEM–3).

STANDOFFS

MA-X0541-89

Figure MEM–3

MEM–4

Memory

Removing the standoffs

NOTE
Removing the two standoffs allows space for the 4 or 12 Mbyte
memory module when these modules are attached to the 8 or
16 Mbyte memory module. The 4 or 12 Mbyte memory module
uses the two shorter standoffs for support.
7. Align the expansion memory module connector with the system
module expansion memory connector and press down on the expansion
memory until it is fully seated.
8. Refer to either the Model 10 or Model 20 chapter for the system
reassembly procedure.
9. After power up and a successful completion of the self-tests, verify
the new memory configuration by entering the SHOW MEMORY
command at the console prompt (>>>).
10. For memory configuration equivalent values refer to Appendix B.

Dual Memory Module Installation
1. Refer to either the Model 10 or Model 20 chapter for the system
disassembly procedure.
2. Align the expansion memory connectors and press modules together
until both modules are fully seated (Refer to Figure MEM–2).
3. Install the "E" clips onto the expansion memories (Refer to
Figure MEM–2).
4. Remove the two taller standoffs which supported the expansion
memory by bending them over until they snap off. Discard the
standoffs. (Refer to Figure MEM–3).
NOTE
Removing the two standoffs allows space for the 4 or 12 Mbyte
memory module when these modules are attached to the 8 or
16 Mbyte memory module. The 4 or 12 Mbyte memory module
uses the two shorter standoffs for support.
5. Align the expansion memory module connector with the system
module expansion memory connector and press down on the expansion
memory until it is fully seated (Refer to Figure MEM–2).
Memory MEM–5

6. Refer to either the Model 10 or Model 20 chapter for the system
reassembly procedure.
7. After power up and a successful completion of the self-tests, verify
the new memory configuration by entering the SHOW MEMORY
command at the console prompt (>>>).
8. For memory configuration equivalent values see Appendix B.

MEM–6

Memory

Communications
This chapter contains installation procedures for the communications
option, available for the MicroVAX 3100 and VAXserver 3100 system.
This chapter also provides instructions for the installation of the
DSH32-Yx second synchronous line driver/receiver module and asociated
cabling.

Installation Procedure for the Communications
Option
1. Refer to either the Model 10 or Model 20 chapter for the system
disassembly procedure.
2. Connect the DSH32 communications cable (part number 17-02294-01)
to the DSH32 Communications module (Refer to Figure COM–1).
3. Align the interface connector on the DSH32 module with the
communications interface connector on the system module (Refer
to Figure COM–1).

Communications COM–1

17-02294-01
Cable

17-02298-01
Cable

54-18905-01
DSH32 Module

Cable Removed
for Clarity

MA-1148-90.DG

Figure COM–1

DSH32 Module

4. Press down on the DSH32 module until it is fully seated
5. Press down on the outer edge of the DSH32 module to secure it onto
the standoff tabs.
6. Refer to either the Model 10 or Model 20 chapter for the system
reassembly procedure.
7. After power up and successful completion of the self-tests, verify the
DSH32 installation by entering the "T 50" command at the console
prompt (>>>).
For errors note the DSH32-A and DSH32-S lines (Refer to
Figure COM–2).

COM–2 Communications

>>> TEST 50
KA41-A V1.4
ID 08-002B-03-79-1F
CLK
0000.0001
NVR
0000.0001
DZ
0000.4001
00004001 00000001 00000001 00000000 00000000
MEM
0004.0001
00400000
MM
0000.0001
FP
0000.0001
IT
0000.0001
SCSI-A
7711.0001 V1.0
FFFFFF05 FFFFFF05 FFFFFF05 00000001 FFFFFF03 FFFFFF05
SCSI-B
1C1C.0001 V1.0
FFFFFF05 FFFFFF05 . . . 00000001 . . . FFFFFF03 FFFFFF05
SYS
0000.0000
DSH32-A
00FF.0000 V2.0
DSH32-S
0000.0001 V2.0
NI
0000.0001
>>>

Figure COM–2

Configuration Table (T 50)

DSH32-Yx
This secction provides instructions for the installation of the DSH32-Yx
second synchronous line driver/receiver module and associated cabling.
This procedure may be used in addition with the DSH32-Bx installation
for simultaneous installation of the DSH32-Bx control module and the
second synchronous line module or separately as a second synchronous
line upgrade.
CAUTION
Wear an anti-electrostatic wrist strap and use an anti-electrostatic
mat when installing or replacing filed replaceable units (FRUs).

Kit Contents
A parts list breakdown of the appropriate line interface kit is provided in
the following table:

Communications COM–3

Table COM–1 DSH32 Second Synchronous Line Upgrade Kits
DSH32 -

12-27591-01

Adaptor, Conn., Male to Female

17-01871-01

Cable Assembly, 16 Cond.

17-01872-01

Cable Assembly, 16 Cond.

17-01873-01

Cable Assembly, 16 Cond.

17-02298-01

Cable Assembly, Flat

54-17230-01

Module, Driver/Receiver, Sync.

90-09984-07

Screw, Hex., 6/32

NOTE
•

The "YA" kit is the RS232 version. (BC19V-02 = 17-01872-01)

•

The "YB" kit is the RS423 version. (BC19W-02 = 17-01873-01)

•

The "YC" kit is the RS422 version. (BC19U-02 = 17-01871-01)

The DSH32-Yx kit may also contain a bracket along with
two fasteners. These parts are not currently used in the
MicroVAX/VAXserver 3100 systems.

Second Synchronous Line Upgrade Installation
Procedure
1. Bring down the operating system software.
2. Before removing power to the system, enter the T 50 command at the
console prompt (>>>) and note the revision indicated on the line for
DSH32-S (Refer to Figure COM–3).
NOTE
Version 2.0 is the minimum revision required, to support the
second synchronous line of the DSH32-S subsystem.

COM–4 Communications

>>> TEST 50
KA41-A V1.4
ID 08-00-2B-03-79-1F
CLK
NVR
DZ

0000.0001
0000.0001
0000.4001
000000001 00000001 00004001 00000000 00000000
MEM
0004.0001
00400000
MM
0000.0001
FP
0000.0001
IT
0000.0001
SCSI-A
0000.4001 V1.58
FFFFFF05 FFFFFF05 FFFFFF05 00000001 FFFFFF05 FFFFFF03 FFFFFF05
SCSI-B
0000.4001 V1.58
FFFFFF05 FFFFFF05 FFFFFF05 00000001 FFFFFF05 FFFFFF03 FFFFFF05
SYS
0000.0000
DSH32-A
00FF.0000 V1.0
DSH32-S
0000.0001 V2.0
NI
0000.0001
>>>

Figure COM–3

T 50 (DSH32-S Revision)

3. Refer to the Model 20 system disassembly procedure and remove the
upper and lower storage shelves from the system box.
4. Remove the DSH32 communications module (54-18905-01) by
disconnecting the ribbon cable from the distribution module. Release
the module from the four standoffs while separating it from the
system module connector (Refer to Figure COM–1).
5. Relocate jumper "W2" on the DSH32 communications module from
single synchronous line selection to dual synchronous line selection
(Refer to Figure COM–4).

Communications COM–5

17-02298-01
Ribbon Cable

54-17230-01
Driver/Reciever
Module

<W2> Jumper Position
Dual Sync.

54-18905-01
DSH32-B Communication Module
MA-1150-90.DG

Figure COM–4

DSH32 Subsystem FRU’s

COM–6 Communications

6. Connect the second synchronous line cable (17-02298-01) to connector
J3 of the DSH32 communications controller module (Refer to
Figure COM–4).
7. Install the communications controller module by aligning the interface
connectors on the DSH32 module with the communications interface
connectors and four standoffs on the system module. Press down
firmly on the connectors and four corners until the DSH32 module is
seated in place (Refer to Figure COM–1).
8. Connect the original synchronous line ribbon cable back to the
distribution module.
9. Remove the second synchronous port cover plate from the rear bezel
by loosening the two panhead screws (Refer to Figure COM–5).

Communications COM–7

2 S C R E WS

COVER PLATE
ASYNC
PORT

S YN C
P O R TS

E X TE R N A L
S C S I P OR T

ON / OFF
S WI TC H

THICKWIRE
PORT

THINWIRE
PORT

TE R M I N A L
LI N E S

M OD E M
P OR T
MA-1149-90.DG

Figure COM–5

Second Sync Port

10. Mount the second synchronous line driver/receiver module
54-17230-01 to the rear bezel, using the two male to female hex
adapter screws from the DSH32-Yx kit (Refer to Figure COM–6).

COM–8 Communications

Driver/Reciever
Module
54-17230-01

MA-1151-90.DG

Figure COM–6

Second Sync Driver/Receiver Module

Communications COM–9

11. Connect the newly installed second synchronous line cable
17-02298-01 to the driver/receiver module (Refer to Figure COM–4).
12. Refer to to the chapter for Model 20 reassembly procedure and
reassemble the system.
13. After power up and a successful completion of the self-tests, verify the
DSH32-Yx second synchronous line installation by entering the "T 50"
command at the console prompt (>>>) and noting the DSH32-S lines
for any errors (Refer to Figure COM–7).

>>> TEST 50
KA41-A V1.4
ID 08-00-2B-03-79-1F
CLK
NVR
DZ

Figure COM–7

T 50 (DSH32-S Revision)

COM–10 Communications

Disks
Disks
The MicroVAX 3100 and VAXserver 3100 systems utilize the IndustryStandard Small Computer Systems Interface (SCSI) for connection of both
the internal and external disk storage devices. There are two separate
SCSI busses utilized within the MicroVAX 3100/VAXserver 3100 which
are depicted by the SCSI-A bus and the SCSI-B bus. The SCSI-A bus
provides two internal-only ports, while the SCSI-B bus provides one
internal port for the Model 10 system and three internal ports for the
Model 20 system. In addition, the SCSI-B bus provides a connection
for external expansion via the SCSI-B port connector on the rear of the
system unit.

SCSI Bus Configuration Rules
The Industry-Standard SCSI bus provides the following
guidelines:
•

A maximum of eight devices (IDs) per bus, including one used by the
controller, always ID # 6.

•

Total bus length not to exceed four meters, including both inside and
outside the enclosures.

•

The total number of boxes of any type connected to any single SCSI
bus shall not exceed four. This includes one host adapter and up to
three expansion boxes. There may be multiple devices (and therefore
IDs) in a single expansion box.

Disks Disk–1

System Configuration Rules
•

The Model 10 system has provisions for up to three internal, halfheight (3 1/2") devices.

•

The Model 20 system has provisions for up to five internal, half-height
(3 1/2") devices.
Refer to Figure Disk–1 for possible Device configuration of the
lower drive shelf device. Refer to Figure Disk–2 for possible device
configuration of the upper drive shelf (Model 20 only).

Disk–2 Disks

Unused

Distribution
Board
Power
Supply

SCSI-B
SCSI-A

DSH32-B
System Module

To FDI Board
for RX23
Option

TZ30, RX23,
or RZ2x

RZ2x

Additional
Power
Connector
for RX23
Drive

Unused
Drive Mounting Panel

Distribution
Board

SCSI-B
SCSI-A

DSH32-B

Power
Supply

System Module
To FDI Board
for RX23
Option

R Z 2x

RX23 or
RZ2x

R Z 2x

Additional
Power
Connector
for RX23
Drive

Drive Mounting Panel
LJ-00049-TI0

Figure Disk–1
20)

Lower Drive Mounting Panel Locations (Model 10 and
Disks Disk–3

Distribution Board
SCSI-B
SCSI-A
Adapter (TZ30 Only)

SCSI-B Connector

Power
Supply
Lower Drive
Mounting Panel

Upper Drive
Mounting Panel

RZ23
Disk
Drive

Upper Drive Panel Power
Lower Drive Panel Power
Data
LJ-00050-TI0

Figure Disk–2

Disk–4 Disks

Upper Drive Mounting Panel Locations (Model 20 only)

•

System external expansion is limited by the number of devices
contained internally within the system enclosure on the SCSI-B
bus. External storage devices are typically full-height (5 1/4") RZtype disks, contained within either the BA40 or BA42 expansion
enclosures.

Disks Disk–5

Available Options
The following table provides a list of the currently available add-on disk
options for the MicroVAX 3100 and VAXserver 3100 system. There is one
flexible type RX diskette drive available as well as both half-height and
full-height hard RZ type disks.

Disk–6 Disks

Table Disk–1 Available Options
Internal
/External

Number

Capacity

Form Factor

RX23-EP

1.4 Mbyte

Half Height

Internal
Model
10

RX23-EK

1.4 Mbyte

Half Height

Internal
Model
20

RZ23-EF

104 Mbyte

Half Height

Internal
Model
10/20

RZ24-EF

209 Mbyte

Half Height

Internal
Model
10/20

RZ55-FA/F3

332 Mbyte

Full Height

External
BA40

SZ12A-XA/XB

332 Mbyte

Full Height

External
BA42
(1RZ55)

SZ12A-AA/AB

664 Mbyte

Full Height

External
BA42
(2RZ55)

SZ12B-XA/XB

665 Mbyte

Full Height

External
BA42
(1RZ56)

SZ12B-AA/AB

1.3 Gbyte

Full Height

External
BA42
(2RZ56)

SZ12C-XA/XB

1.0 Gbyte

Full Height

External
Disks Disk–7
BA42
(1RZ57)

SZ12C-AA/AB

2.0 Gbyte

Full Height

External
BA42
(2RZ57)

RX23 Disk Drive
RX23 Installation
This section provides instructions for installing an RX23 option into a
Model 10 or Model 20 MicroVAX 3100 or VAXserver 3100 system.
CAUTION
Installation of this drive should only be attempted by qualified
personnel. Improper installation can result in system damage for
which Digital is not responsible. Please contact your Customer
Service Representative.

RX23 Disk Drive RX23–1

Kit Contents
There are two different RX23 kits available, one for Model 10 systems
and one for Model 20 systems. The contents of the kits are given in
Table RX23–1.
Table RX23–1 Kit Contents
Quantities
Description

Part Number

Model 10 Kit

Model 20 Kit

RX23 diskette drive

RX23-AA

FDI board

54-19288-01

Bracket

74-38638-01

Rubber grommets

90-00018-02

Panhead screws

12-27886-02

Ribbon cable

17-02221-02

Diskette

30-30083-01

Cover (bezel)

74-39104-01

–

Short standoff

12-23824-01

–

Fixing (standoffs)

90-11044-01

Bezel

74-39959-01

–

SCSI ROM V1.58

23-061E8-00

RX23–2 RX23 Disk Drive

Determining the Revision Level of the SCSI ROM
The RX23 diskette drive option is supported by systems which have a
SCSI ROM revision level V1.58 or higher. If the revision level of the SCSI
ROM is less than V1.58, the existing ROM must be replaced by the ROM
supplied with the RX23 installation kit.
Before you power down the system, determine the revision level of the
SCSI ROM as follows:
1. Press the halt button on the rear of the system unit to put the system
in console mode.
2. At the console prompt (>>>), enter T 50. The system configuration is
displayed.
3. Note the revision levels (Vx.xx) on the lines beginning SCSI-A and
SCSI-B.
If the revision level is V1.58 or greater, continue with the installation
procedure as described in Setting the SCSI ID of the RX23 Option. If
the revision level is less than V1.58, replace the ROM as described in
Replacing the SCSI ROM.

Replacing the SCSI ROM
Replace the SCSI ROM as follows:
1. Power down the system unit.
2. Disassemble the system to gain access to the System Module. Refer
to the FRU Removal and Replacement procedures for Model 10
and Model 20 systems in the MicroVAX 3100 and VAXserver 3100
Maintenance Guide (EK-A0372-MG.001).
3. Locate the SCSI ROM identified in Figure RX23–1.

RX23 Disk Drive RX23–3

SCSI ROM

MLO-003906
LJ-00076-TI0

Figure RX23–1

Location of SCSI ROM on the System Module

4. Carefully remove the ROM from its retaining socket noting the
position of pin 1 identified by a notch on the chip.
CAUTION
Be careful not to bend the pins of the new ROM.
5. Install the ROM supplied with the same orientation as the ROM just
removed.
6. Reassemble the system.

Setting the SCSI ID of the RX23 Option
Before installation, you must assign a unique SCSI ID number to the
RX23 option. If you are unsure about the assignment of SCSI ID numbers
to devices, refer to the section entitled SCSI Bus Address ID Settings in
the MicroVAX 3100 and VAXserver 3100 Maintenance Guide.
NOTE
Perform a "SHOW DEVICE" command at the console prompt to
determine the available SCSI ID numbers. This must be done
to avoid SCSI ID address duplication. Refer to Appendix C for
examples of the "SHOW DEVICE" command.
If you are familiar with the assignment of SCSI IDs, you can set the
SCSI ID of the RX23 option using the switches on the FDI board.
Figure RX23–2 shows the location of the SCSI ID switches on the FDI
board and Table RX23–2 lists the possible SCSI ID switch settings.
RX23–4 RX23 Disk Drive

1
2
3
OFF
ON

SCSI ID Switches
MLO-003273

Figure RX23–2

RX23 FDI Board SCSI ID Switch Locations

RX23 Disk Drive RX23–5

Table RX23–2 RX23 SCSI ID Switch Settings
SCSI ID

RX23 Switch Settings
1

Off

1 Reserved address ID for SCSI bus controller.
2 Recommended address IDs for RX23 drives on the SCSI-A bus.
3 Recommended address IDs for RX23 drives on the SCSI-B bus.
4 Reserved for the device with the highest priority on the bus.

Installing an RX23 Option in a Model 10 System
Prepare the Model 10 system as follows:
1. Refer to the Model 10 chapter for system disassembly procedure.
2. If there are three RZ23 disk drives in the system unit, you must
remove the RZ23 in the right-hand compartment.
Install the RX23 diskette drive option as follows:
1. Ensure that you have all the items listed in Table RX23–1.
2. Insert the four rubber grommets into the holes on the bracket. See
Figure RX23–3.
3. Secure the RX23 diskette drive to the bracket using the four panhead
screws provided. See Figure RX23–3.

RX23–6 RX23 Disk Drive

Panhead Screw
(4 Places)
Rubber Grommet
(4 Places)
Mounting Bracket
RX23 Diskette Drive

MLO-003520

Figure RX23–3

Securing the RX23 to the Bracket

4. Fit the six standoffs to the drive mounting panel. See
Figure RX23–4.

RX23 Disk Drive RX23–7

RX23 Diskette Drive
Mounting Bracket
Captive Screw
(4 places)

RX23 FDI Board
Holes for RX23
Mounting Bracket
(4 places)
Standoffs (6 places)
Drive Mounting Panel

MLO-003522

Figure RX23–4

RX23 Installation in Model 10 Systems

5. Connect one end of the the ribbon cable provided to the FDI board.
6. Attach the FDI board to the standoffs. See Figure RX23–4.
7. Secure the drive/bracket assembly to the drive mounting panel using
the captive screws on the bracket. See Figure RX23–4.
8. Connect the SCSI cable to the 50-way connector on the FDI board.
9. Connect the other end of the ribbon cable to the RX23 diskette drive.
10. Connect the large 4-way power connector to the FDI board and
connect the small 4-way power connector to the RX23 diskette drive.
11. Gently lever the blanking plate out from the front bezel of the system
box using a flat screwdriver, taking care not to damage the main
bezel.
12. Insert the RX23 bezel provided.
13. Reassemble the system.

RX23–8 RX23 Disk Drive

Installing an RX23 Option in a Model 20 System
Prepare the Model 20 system as follows:
1. Refer to the Model 20 chapter for system disassembly procedure.
2. If necessary, remove any device occupying the compartment in which
you want to install the RX23. If this device is an RZ23 or RZ24 disk
drive, it may be possible to reinstall it on the upper drive mounting
panel, depending on the configuration.
Install the RX23 diskette drive option as follows:
1. Ensure that you have all the items listed in Table RX23–1.
2. Insert the four rubber grommets into the holes on the bracket. See
Figure RX23–3.
3. Secure the RX23 diskette drive to the bracket using the four panhead
screws provided. See Figure RX23–3.
4. Fit the five long standoffs and one short standoff to the lower drive
mounting panel. See Figure RX23–5.

RX23 Disk Drive RX23–9

RX23 Diskette Drive
Mounting Bracket
Captive Screw
(4 places)

RX23 FDI Board
Short Standoff
(1 place)

Long Standoffs
(5 places)
Holes for RX23
Mounting Bracket
(4 places)
Lower Drive
Mounting Panel
Holes for
Long Standoffs
(5 places)

Holes for RX23
Mounting Bracket
(4 places)

Hole for
Short Standoff

ALTERNATIVE POSITIONING
MLO-003523

Figure RX23–5

RX23 Installation in Model 20 Systems

NOTE
Figure RX23–5 shows the RX23 diskette drive installed in the
left-hand compartment. For systems which do not have a TZ30
tape drive, the RX23 diskette drive should be installed in the
right-hand compartment. The alternative positioning of the
fittings is shown.
5. Connect one end of the the ribbon cable provided to the FDI board.
6. Attach the FDI board to the standoffs. See Figure RX23–5.
7. Secure the drive/bracket assembly to the lower drive mounting panel
using the captive screws on the bracket. See Figure RX23–5.
RX23–10 RX23 Disk Drive

8. Connect the SCSI cable to the 50-way connector on the FDI board.
9. Connect the other end of the ribbon cable to the RX23 diskette drive.
10. Connect the large 4-way power connector to the FDI board and
connect the small 4-way power connector to the RX23 diskette drive.
11. Gently lever the blanking plate out from the front of the system box
metalwork. This blanking plate is concealed behind the door on the
front of the system unit.
12. Insert the RX23 bezel provided.
13. Reassemble the system.
14. Power up any expansion boxes first and then the sytem box.
15. After power up and a successful completion of self-test, verify the
presence of the new device by entering the "SHOW DEVICE"
command at the console prompt (>>>). Refer to Appendix C for
"SHOW DEVICE" command examples.

Post-Installation Testing
See the section entitled General SCSI Bus Troubleshooting and the
section entitled Troubleshooting an RX23 Diskette Drive in the MicroVAX
3100 and VAXserver 3100 Maintenance Guide for information on testing
the RX23 diskette drive installation.

RX23 Disk Drive RX23–11

RZ23 Disk Drive
The following information provides instructions for installing the RZ23
option into a MicroVAX 3100 or VAXserver 3100 system.

CAUTION
Wear an anti-electrostatic wrist strap and use an anti-electrostatic
mat when installing or replacing field replaceable units (FRUs).
The RZ23 can only be installed in the system box.

Internal Storage Device Locations
1. Bring the operating system down and halt the system
2. At the console prompt (>>>), enter the "SHOW DEVICE" command
to determine the existing SCSI address ID’s. Refer to Appendix C for
"SHOW DEVICE" command examples.
NOTE
This must be done to avoid possible address duplication.
3. Determine the SCSI address and set the SCSI ID Jumpers using
Table RZ23–1 and Figure RZ23–1.

RZ23 Disk Drive RZ23–1

Table RZ23–1 RZ23 SCSI ID Jumper Combinations
Address ID on

RZ23 Jumper Settings

SCSI Bus

Out

1†

Out

2†

Out

32 †

Out

1 Reserved address ID for SCSI bus controller.
2 Recommenced address IDs for the RZ23 drives on SCSI-A bus.

†Recommenced address IDs for the RZ23 drives on SCSI-B bus.

RZ23–2 RZ23 Disk Drive

Signal Connector

Connector to HDA Module

E1
E2
E3

SCSI ID Jumper Wires

Power Connector
MLO-002943

Figure RZ23–1

RZ23 SCSI Jumper Locations

4. Power down the system box and any expansion boxes.
5. Refer to either the Model 10 or Model 20 chapter for the system
disassembly procedure.
NOTE
Refer to the system configuration rules in the DISK chapter
for possible drive locations.
6. Install the disk drive in the desired location and secure it in place,
using only the four philips pan-head screws.
7. Refer to either the Model 10 or Model 20 chapter for the system
reassembly procedure.
8. Power up any expansion boxes first and the system box last.
RZ23 Disk Drive RZ23–3

9. After power up and a successful completion of the self-tests, verify the
presence of the RZ23 by entering the "SHOW DEVICE" command at
the console prompt (>>>) and noting the RZ23 under the DEVNAM
column. Refer to Appendix C for "SHOW DEVICE" command
examples.

RZ23–4 RZ23 Disk Drive

RZ24 Disk Drive
RZ24 Installation
CAUTION
Wear an anti-electorstatic wrist strap and use an anti-electrostatic
mat when installing or replacing field replaceable units.
IMPORTANT
The RZ24 can only be installed in the system box.
This section provides instructions for installing an RZ24 option into a
MicroVAX 3100 or VAXserver 3100 system.

CAUTION
Installation of this drive should only be attempted by qualified
personnel. Improper installation can result in system damage for
which Digital is not responsible.
Please contact your Customer Service Representative.

Installing the RZ24 Option
1. Bring the operating system down.
2. At the console prompt (>>>), enter the "SHOW DEVICE" command
to determine the existing SCSI address ID’s. Refer to Appendix C for
"SHOW DEVICE" command examples.
NOTE
This must be done to avoid possible address duplication.
3. Determine the SCSI address and set the SCSI ID Jumpers using
Table RZ24–1 and Figure RZ24–1.

RZ24 Disk Drive RZ24–1

Table RZ24–1 RZ24 SCSI ID Jumper Combinations
Address ID on

RZ24 Jumper Settings

SCSI Bus

Out

1†

Out

2†

Out

32 †

Out

1 Reserved address ID for SCSI bus controller.
2 Recommenced address IDs for the RZ24 drives on SCSI-A bus.

†Recommenced address IDs for the RZ24 drives on SCSI-B bus.

RZ24–2 RZ24 Disk Drive

TERMINATOR
PACKS

SCSI ID
JUMPERS

50 PIN SCSI
SIGNAL
CONNECTOR
E3

E1
E2

CONNECTOR TO
HDA MODULE

POWER
CONNECTOR

PARITY
JUMPER

SHR_X1142A_89

Figure RZ24–1

RZ24 Jumpers

4. Power down the system box and expansion boxes (if applicable).
5. Refer to either the Model 10 or Model 20 chapter for the disassembly
procedure.
NOTE
Refer to the system configuration rules in the DISK chapter
for possible drive locations.
6. Install the disk drive in the desired location and secure it in place,
using the four Philips pan-head screws provided.
7. Refer to either the Model 10 or Model 20 chapter for the reassembly
procedure.
8. Power up any expansion boxes first and then the system box.

RZ24 Disk Drive RZ24–3

9. After power up and a successful completion of self-test, verify the
presence of the new device by entering the "SHOW DEVICE"
command at the console prompt (>>>) and noting the RZ24 under
the DEVNAM column. Refer to Appendix C for "SHOW DEVICE"
command examples.

RZ24–4 RZ24 Disk Drive

RZ55 (in BA40 Disk Expansion
Box)
This chapter provides instructions for connecting the RZ55/BA40 Disk
expansion to the MicroVAX 3100 or VAXserver 3100 system.
For information regarding the connection of the RZ55 in the BA42
expansion box, refer to chapter SZ12x.
The BA40 disk expansion box connects to the system box through the
external SCSI port. The SCSI cable connects to either of the two ports
on the back of the expansion box. However, the SCSI terminator must be
installed on the unused connector unless another expansion box is daisy
chained.
If the SCSI port already has a box connected to it, use another SCSI
cable to connect the BA40 disk expansion box to the last box on the daisy
chain. Be sure to move the terminator onto the unused connector on the
back of the last expansion box in the daisy chain. Figure RZ55–2 and
Figure RZ55–3 show how the BA40 disk expansion box(es) connect to the
system box.

Adding a Single BA40 Disk Expansion Box
1. Bring the operating system down and halt the system.
2. At the console prompt (>>>), enter the "SHOW DEVICE" command to
determine the existing SCSI address ID’s. Refer to Appendix C.
3. Determine the SCSI address and set the SCSI ID Jumpers using
Table RZ55–1 and Figure RZ55–1.
NOTE
This must be done to avoid possible address duplication.

RZ55 RZ55–1

Table RZ55–1 SCSI Address and SCSI ID Jumper Settings
Address ID on

BA40 Disk Expansion Box Switch Settings

SCSI Bus

Down

1 Recommended address ID for the RZ55 disk drive.
2 Reserved address ID for SCSI controller.

RZ55–2 RZ55

12 3
ON

OPEN

MA-X1179-88

MLO-003321

Figure RZ55–1

BA40 Disk Expansion Box SCSI ID Switch Locations

4. Power down the system box and any expansion boxes.
5. Connect the SCSI data cable from the BA40 to the SCSI-B port
connector on the system box, making sure the bail locks have been
secured in place.
6. Install the SCSI terminator on the rear of the BA40, making sure the
bail locks have been secured in place. (Refer to Figure RZ55–2).
7. Connect the power cord to the expansion box receptacle. (Refer to
Figure RZ55–2).
IMPORTANT
If you have more than one expansion box, plug all expansion
boxes into the same power source.
8. Power up the expansion boxes first and then the system box.
RZ55 RZ55–3

9. After power up and a successful completion of the self-tests, verify
the presence of the RZ55 by entering the "SHOW DEVICE" command
at the console prompt (>>>) and noting the new device under the
DEVNAM column. Refer to Appendix C for the "SHOW DEVICE"
command examples.

Terminator

Connector Cable

Power Cord

MLO-002764

Figure RZ55–2

RZ55 Expansion Box Connection

Adding Multiple BA40 Disk Expansion Boxes
1. Bring the operating system down and halt the system.
2. At the console prompt (>>>), enter the "SHOW DEVICE" command to
determine the existing SCSI address ID’s. Refer to Appendix C for the
"SHOW DEVICE" command examples.
NOTE
This must be done to avoid possible address duplication.
RZ55–4 RZ55

3. Determine the SCSI address and set the SCSI ID Jumpers using
Table RZ55–1 and Figure RZ55–1.
4. Power down the system box and any expansion boxes.
5. Connect the SCSI expansion cable from the first BA40 Disk expansion
box to the system box, making sure the bail locks have been secured
in place (Refer to Figure RZ55–3).

Terminator

50-Pin to 50-Pin
Connector Cable

MLO-002762

Figure RZ55–3

Dual BA40 Disk Expansion Connections

6. Connect the SCSI expansion cable from the second BA40 to the first
BA40 Disk expansion box, making sure the bail locks have been
secured in place (Refer to Figure RZ55–3).

RZ55 RZ55–5

7. Install the SCSI terminator on the rear of the last BA40, making sure
the bail locks have been secured in place (Refer to Figure RZ55–3).
8. Connect the power cord to the expansion box receptacle. (Refer to
Figure RZ55–3).
IMPORTANT
If you have more than one expansion box, plug all expansion
boxes into the same power source.
9. Power up the expansion box(es) first and then the system box.
10. After power up and a successful completion of the self-tests, verify
the presence of the RZ55 by entering the "SHOW DEVICE" command
at the console prompt (>>>) and noting the new device under the
DEVNAM column. Refer to Appendix C for the "SHOW DEVICE"
command examples.

RZ55–6 RZ55

SZ12x (in BA42 Disk Expansion
Box)
Installation and Upgrade of the SZ12x (BA42)
This section refers to the installation, and upgrade, of the SZ12x (BA42)
storage expansion box. It includes details for setting up and using the
storage expansion box for the first time, and information on adding a
storage device to the storage expansion box.
An expansion box is an external box that connects to your system unit to
provide additional disk storage space.
The storage expansion box holds the following devices:
•

RZ55 - 332-megabyte full-height SCSI disk

•

RZ56 - 665-megabyte full-height SCSI disk

•

RZ57 - 1.0-gigabyte full-height SCSI disk

The preceeding drives come in preconfigured combinations contained
within the BA42 expansion box (Refer to Table SZ12x–1).

Storage Expansion Box Configurations
Table SZ12x–1 Storage Expansion Box Configurations
Description

Order Number

Single RZ55 expansion box

SZ12A-XA/XB

Double RZ55 expansion box

SZ12A-AA/AB

Single RZ56 expansion box

SZ12B-XA/XB

Double RZ56 expansion box

SZ12B-AA/AB

Single RZ57 expansion box

SZ12C-XA/XB

Double RZ57 expansion box

SZ12C-AA/AB

SZ12x Disk Drive SZ12x–1

Guidelines for Connecting Storage Expansion
Boxes
•

You can connect up to three expansion boxes as long as you do not
connect more than six devices.

•

You must connect the SCSI terminator (50 pin) that comes with your
storage expansion box to the unused SCSI port on the back of the last
expansion box on the bus.

•

All expansion boxes should be plugged into the same power source or
electrical outlet.

•

The length of cable from the SCSI expansion port on the system unit
to the last device on the SCSI bus must not exceed 4 m (13 ft).

•

Be sure to power on the expansion boxes in the following order (prior
to powering on the system unit):
1. Disk storage expansion box
2. TK50Z tape expansion box
3. RRD40 compact disk expansion box

Connecting One Expansion Box
To connect one expansion box to your system unit, perform the following
steps:
1. Bring the operating system down and halt the system.
2. At the console prompt (>>>), enter the "SHOW DEVICE" command
to determine the existing SCSI address ID’s. Refer to Appendix C for
"SHOW DEVICE" command examples.
NOTE
This must be done to avoid possible address duplication.
3. Unpack the expansion box and place it with the back of the unit
facing you.
4. Make sure that the power switch is in the off (0) position.

SZ12x–2 SZ12x Disk Drive

5. To set the SCSI ID switch positions, do the following:
a. Remove the SCSI switch cover by placing your fingers under
the locking tab and lifting the cover to release it (Refer to
Figure SZ12x–1).

SCSI Cover
Lift Locking Tab
to Release

MLO-003514

Figure SZ12x–1
Box

Removing the SCSI Switch Cover on the Expansion

b. Determine the SCSI address and set the SCSI ID jumpers using
Table SZ12x–2, Figure SZ12x–2.

SZ12x Disk Drive SZ12x–3

Table SZ12x–2 SZ12x Expansion Box SCSI Address ID’s and Switch
Positions
Address ID on

SZ12x Expansion Box Switch Settings

SCSI Bus

Down

SZ12x–4 SZ12x Disk Drive

ID 1

ID 0

MLO-003462

Figure SZ12x–2

SCSI Switch Settings on Storage Expansion Box

To reset a SCSI select switch, use a pen or small pointed object to
flip the switch.

6. Replace the SCSI select switch cover.
7. Power down the system unit.
8. Place the SZ12x expansion box on top of the system box.
9. Connect the 50-pin SCSI I/O cable from the expansion box to the
SCSI-B port connector on the system unit (Refer to Figure SZ12x–3).

SZ12x Disk Drive SZ12x–5

SCSI
TERMINATOR

TO
S YSTEM
B OX
GSF_1256_89.DG

Figure SZ12x–3

SCSI I/O Cable Connection

10. Rotate the bail lock loops forward to lock cable(s) into place.
11. Connect the SCSI terminator (50-pin) to the unused port on the
storage expansion box.
12. Connect the power cord to the expansion box receptacle (Refer to
Figure SZ12x–4).
NOTE
If you have more than one expansion box, plug all expansion
boxes into the same power source.

SZ12x–6 SZ12x Disk Drive

Power Cord

MLO-003512

Figure SZ12x–4

Connecting the Power Cord

13. Power up the expansion boxes in the previously recommended order.
Refer to Guidelines for Connecting Storage Expansion Boxes.
14. Power up the system box (last).
15. At the console prompt (>>>), again enter the "SHOW DEVICE"
command to display the current SCSI storage devices on the system.
Ensure that all devices are recognized and that each device has its
own unique SCSI ID. Refer to Appendix C for "SHOW DEVICE"
command examples.

SZ12x Disk Drive SZ12x–7

Daisy-Chaining Two Expansion Boxes
You can add additional expansion boxes by daisy-chaining (linking two
expansion boxes together in a series).
To daisy-chain one expansion box to another expansion box, follow the
instructions below:
1. Bring the operating system down and halt the system.
2. At the console prompt (>>>), enter the "SHOW DEVICE" command
to determine the exisitng SCSI address ID’s. Refer to Appendix C for
"SHOW DEVICE" command examples.
NOTE
This must be done to avoid possible address duplication.
3. Make note of the used SCSI IDs and power down the entire system.
4. Remove the 50-pin terminator on the first expansion box.
5. Connect the SCSI I/O cable from the available port on the first
expansion box to the first port on the second expansion (Refer to
Figure SZ12x–5).

SZ12x–8 SZ12x Disk Drive

Power Cord

MLO-003497

Figure SZ12x–5

Connecting the SCSI I/O Cable

6. Attach the 50-pin terminator to the unused SCSI port on the
expansion box
7. Refer back the the previous section on single expansion box
installation for information on setting the SCSI address ID, and
configure the second expansion box accordingly.
8. Connect the power cord to the expansion box power receptacle and
plug the other end into a common electrical outlet.
9. Power up the expansion boxes in the previously recommended order.
Refer to Guidelines for Connecting Storage Expansion Boxes.
10. Power up the system box (last).
SZ12x Disk Drive SZ12x–9

11. At the console prompt (>>>), again enter the "SHOW DEVICE"
command to display the current SCSI storage devices on the system.
Ensure that all devices are recognized and that each device has its
own unique SCSI ID. Refer to Appendix C for "SHOW DEVICE"
command examples

Adding a Disk Drive
This Section describes how to install a second disk drive inside your
BA42 disk storage expansion box. For the available add-on disks refer to
Table SZ12x–3.
Table SZ12x–3 Additional Disks for SCSI Expansion Boxes
Order
Number

Description

RZ55-UK

One 332-Mbyte disk drive add-on for BA42

RZ56-UK

One 665-Mbyte disk drive add-on for BA42

RZ57-UK

One 1.0-Gbyte disk drive add-on for BA42

Installing the Additional Drive
1. Bring the operating system down and halt the system.
2. At the console prompt (>>>), enter the "SHOW DEVICE" command
to determine the existing SCSI address ID’s. Refer to Appendix C for
"SHOW DEVICE" command examples.
NOTE
This must be done to avoid possible address duplication.
3. Power off your equipment in the following order:
1. Expansion boxes
2. Printer, modem, or other equipment
3. System unit and monitor
4. Disconnect all cables from the expansion box (which the additional
disk is to be installed in) and place the expansion box in a suitable
place to be worked on.
SZ12x–10

SZ12x Disk Drive

5. Take precautions to protect devices from possible damage due to
electrostatic discharge.
CAUTION
Wear an anti-electrostatic wrist strap and use an antielectrostatic mat when handling devices that are inside the
expansion box.
6. Remove the expansion box cover by loosening the two captive screws
(Refer to Figure SZ12x–6).

Cover Screws
MLO-003495

Figure SZ12x–6

Removing the Expansion Box Cover

7. Place the expansion box so that the front is facing you.

SZ12x Disk Drive SZ12x–11

8. Slide the three internal cables inside the expansion box out of the
restraining clamp.
9. Tilt the disk drive as you place it in the drive’s mount holes (Refer to
Figure SZ12x–7).

Mount Holes

Mount Holes
MLO-003513

Figure SZ12x–7

Mounting the Drive

10. Secure the drive by tightening the mounting screw on the drive you
just mounted (Refer to Figure SZ12x–8).

SZ12x–12

SZ12x Disk Drive

RZ56
Power
Supply

RZ56

Mounting
Screws

Figure SZ12x–8

MLO-003494

Securing the Drive

11. Connect the following cables to the back of the drive (Refer to
Figure SZ12x–9).
•

Internal power cable

•

Internal SCSI bus cable

•

Internal SCSI ID select cable

SZ12x Disk Drive SZ12x–13

Internal SCSI
Bus Cable

Power
Supply

SCSI ID
Select Cable

RZ56

Internal Power Cable
MLO-003493

Figure SZ12x–9

Connecting the Cables

12. Fold the internal cables out of the way of the expansion box cover.
13. Replace the expansion box cover and tighten the two captive cover
screws.
14. Reconnect the power and SCSI data cables to the expansion box.
15. Refer back to Table SZ12x–2 and Figure SZ12x–2 for information on
setting the SCSI address IDs.
16. Turn on the system in the following order:
1. SZ12x expansion box(es)
2. TK50Z tape expansion box (if applicable)
SZ12x–14

SZ12x Disk Drive

3. RRD40 compact disk expansion box (if applicable)
4. Printer(s) and/or modem. (if applicable)
5. System Unit and monitor
17. After a successful completion of the self-tests, enter the "SHOW
DEVICE" command to display the current SCSI storage devices on the
system. Ensure all devices are recognized and each device has its own
unique SCSI ID. Refer to Appendx C for "SHOW DEVICE" command
examples.

SZ12x Disk Drive SZ12x–15

TZ30 Tape Drive
The MicroVAX 3100 and VAXserver 3100 tape drive options are divided
into both internal and external options in relation to the system box.

TZ30 Tape Drive
The TZ30 tape drive option can only be installed in the system
box.
It can only be positioned in the lower right-hand storage compartment of
the lower shelf, as viewed from the front.

TZ30 Tape Drive TZ30–1

TZ3 0

LJ-00051-TI0

Figure TZ30–1

Installing TZ30 Tape Drive

TZ30 Tape Drive Installation Procedure
1. Bring the Software Operating System down and halt the system.
2. At the console prompt (>>>), enter the command "SHOW DEVICE"
to determine existing SCSI address ID’s. Refer to Appendix C for
"SHOW DEVICE" command examples.

TZ30–2 TZ30 Tape Drive

NOTE
This must be done to avoid possible address duplication.
3. Determine the SCSI address and set the SCSI ID switches on the
TZ30 tape drive using Table TZ30–1 and Figure TZ30–2 for SCSI ID
jumper location.
Table TZ30–1 TZ30 SCSI ID Switch Settings
Address ID on

TZ30 Jumper Settings

SCSI Bus

Off

1 Reserved address ID for SCSI bus controller.
2 Recommenced address IDs for the TZ30 tape drive.

TZ30 Tape Drive TZ30–3

TZ30 TOP

RIGHT SIDE

FRONT

SCSI ID BIT:0
SCSI ID BIT:1
SCSI ID BIT:2
SCSI PARITY
ENABLE/
DISABLE

OFF

4
3
2
1
ON
OFF

EXAMPLE OF SCSI ID SET TO 5 WITH PARITY ON.
MA-X1084-88

Figure TZ30–2

TZ30 SCSI ID Switch Locations

4. Power off the system box and expansion boxes (if applicable).
5. Refer to either the Model 10 or the Model 20 chapter for the
disassembly procedure.
6. Using the four slotted screws and four rubber grommets, mount the
tape drive into the lower drive shelf (Refer to Figure TZ30–3).

TZ30–4 TZ30 Tape Drive

DRIVE PLATE

SCREWS

MA-X0524-89

Figure TZ30–3

Mounting Tape Drive in Lower Drive Shelf

TZ30 Tape Drive TZ30–5

7. Connect the SCSI data cable.
8. Connect the DC power connector to the rear of the TZ30 tape drive.
9. Refer to either the Model 10 or Model 20 chapter for the reassembly
procedures.
10. Power up the system, making sure that all expansion boxes are
powered on first (if applicable).
11. After power up and successful completion of Self-Test, verify presence
of the tape drive just intalled by entering the "SHOW DEVICE"
command at the console prompt (>>>), and noting the tape under
the DEVTYPE column. Refer to Appendix C for "SHOW DEVICE"
command examples.

TZ30–6 TZ30 Tape Drive

TK50Z Tape Drive (in a BA40
Expansion Box)
The MicroVAX 3100 and VAXserver 3100 tape drive options are divided
into both intrnal and external options in relation to the system box.
The TK50Z tape drive option is offered in a BA40 Expansion Box.

TK50

MLO-003345

Figure TK50Z–1

TK50Z Expansion Box

TK50Z Tape Drive TK50Z–1

This expansion box connects to the system box through the external SCSI
(B) port. The SCSI cable connects to either of the two ports on the back of
the expansion box. The SCSI terminator must be installed on the unused
connector unless another expansion box is daisy chained. If the external
SCSI port has a box already connected to it, you must use another cable
to connect the TK50Z expansion box to the last box on the daisy chain. Be
sure to move the terminator onto the unused connector on the back of the
last expansion box in the daisy chain.

TK50Z Installation Procedure
1. Bring the Software Operating System down and halt the system.
2. At console prompt (>>>), enter the command "SHOW DEVICE"
to determine existing SCSI address ID’s. Refer to Appendix C for
"SHOW DEVICE" command examples.
NOTE
This must be done to avoid possible address duplication.
3. Determine the SCSI address and set the SCSI ID jumpers on the
TK50Z expansion box using Table TK50Z–1 and Figure TK50Z–2.
Table TK50Z–1 TK50Z-GA SCSI ID Switch Settings
Address ID on

TK50Z-GA Expansion Box Switch Settings

SCSI Bus

Down

1 Reserved address ID for SCSI bus controller.
2 Recommended address ID for the TK50Z-GA expansion box.

TK50Z–2 TK50Z Tape Drive

12 3

ON
OPEN

MA-X1179-88

MLO-003320

Figure TK50Z–2

TK50Z-GA SCSI Address ID Switch Settings

4. Power off the system box and expansion boxes (if needed).
5. Connect the TK50Z expansion box. Make sure that the SCSI
terminator is installed. If more than one expansion box is present
in the configuration connect the SCSI terminator at the end of the
daisy chain (Refer to Figure TK50Z–3).

TK50Z Tape Drive TK50Z–3

Terminator

Connector Cable

Power Cord

MLO-002764

Figure TK50Z–3

TK50Z Expansion Box Connection

6. Power up the system, making sure that all expansion boxes are
powered on first (if applicable).
7. After power up and successful completion of Self-Test, verify presence
of the tape drive just intalled by entering the "SHOW DEVICE"
command at the console prompt (>>>), and noting the Tape under
the DEVTYPE column. Refer to Appendix C for "SHOW DEVICE"
command examples.

TK50Z–4 TK50Z Tape Drive

CD ROMs
This chapter provides instructions for installing the CD ROM options that
are available for the MicroVAX 3100 and VAXserver 3100 systems.
The RRD40 is available as a desktop expansion box only in it’s
own enclosure.

CD ROM Installation Procedure
1. Bring the operating system down and halt the system.
2. At the console prompt (>>>), enter the "SHOW DEVICE" command
to determine the existing SCSI address ID’s. Refer to Appendix C for
"SHOW DEVICE" command examples.
NOTE
This must be done to avoid possible address duplication.
3. Determine the SCSI address and set the SCSI ID Switch Settings by
using Table CD–1 and Figure CD–1.

CD ROMs CD–1

Table CD–1 RRD40 Expansion Box Switch Settings
Address ID on

RRD40 Expansion Box Switch Settings

SCSI Bus

Down

Not Used

Down

Not Used

Down

Not Used

Down

Not Used

Down

Not Used

Down

Not Used

Down

Not Used

1 Because switch 4 is unsed, it can be in either position.
2 Reserved address ID for SCSI bus controller.
3 Recommended address ID for the RRD40 compact disk drive.

NOTE
The SCSI ID switch is located on the rear bezel of the RRD40.

CD–2 CD ROMs

SCSI ID 4

Down Down Down

Location of SCSI Switches

Bail Lock

Power Cord

22
0

Voltage Selector

MLO-002325

Figure CD–1

RRD40 Expansion Box SCSI Address ID Setting

4. Power down the system box and any expansion boxes.
5. Connect SCSI expansion cable from the RRD40, (Top connector), to
the system box making sure the bail locks have been secured in place.
(Refer to Figure CD–1).

CD ROMs CD–3

6. Install the SCSI terminator to the rear of the RRD40, (bottom
connector), making sure the bail locks have been secured in place.
(Refer to Figure CD–1).
7. Power up RRD40 expansion box before powering up the system box.
8. Power up the system box.
9. After power up and a successful completion of the self-tests, verify
the presence of the RRD40 by entering the "SHOW DEVICE"
command at the console prompt (>>>) and noting the RRD40 under
the DEVNAM column. Refer to Appendix C for "SHOW DEVICE"
command examples.

CD–4 CD ROMs

Power Up Self Tests and
Diagnostics
Power up Self Tests and Diagnostics
There are two types of console test commands, diagnostic test commands,
and utility commands. Table A–1 contains a complete list of the
diagnostic test commands. Table A–2 contains a complete list of the
utility commands.

Appendix A A–1

Table A–1 Diagnostic Test Commands
Test

Description

T F

Self-test for future option (No test
run)

T E

Self-test on time-of-year clock
(CLK)

T D

Self-test on nonvolatile RAM (NVR)

T C

Self-test on serial line controller
(DZ)

T B

Self-test on system memory (MEM)

T A

Self-test on memory management
unit (MM)

T 9

Self-test on floating point unit (FP)

T 8

Self-test on interval timer (IT)

T 7

Self-test on the SCSI-A bus

T 6

Self-test on the SCSI-B bus

T 5

Self-test on interrupt controller
and E-Net ID ROM (SYS)

T 4

Test DSH32-B communications
module async line

T 3

Test DSH32-B communications
module sync line

T 2

Self-test for future option (No test
run)

T 1

Self-test on the Ethernet circuits
(NI)

T 0

Customer mode system exerciser

T 101

Field Service mode system
exerciser (two passes)

T 102

Field Service mode system
exerciser (continuous)

T 80000103

Manufacturing mode system
exerciser

T 80000106

Selects individual devices for
exerciser mode

A–2 Appendix A

Table A–2 Utility Commands
Test

Description

T 50

Configuration display

T 51

Set NVR default boot device

T 52

Set NVR default boot flags

T 53

Set NVR default recovery action
flags

T 73

Special key on Compac Tapes

T 74

Special key on diskettes

T 75

SCSI disk data eraser

T 76

SCSI diskette formatter

Appendix A A–3

Hexadecimal Memory Codes
Table B–1 Hexadecimal Memory Codes
Codes

System Memory

00400000

4 megabyte

00800000

8 megabyte

00C00000

12 megabyte

01000000

16 megabyte

01400000

20 megabyte

01800000

24 megabyte

02000000

32 megabyte

NOTE
The first line displayed indicates the total system memory available.

Appendix B B–1

SHOW DEVICE Command
>>> SHOW DEVICE
VMS/VMB
------ESA0

ULTRIX ADDR
DEVTYP NUMBYTES
------ --------- -------SE0
08-00-2B-03-79-1F

RM/FX
-----

WP
--

DEVNAM
------

DKA300
RZ3
DKA400
RZ4
MKA500
TZ5
...HostID...

A/3/0/00
A/4/0/00
A/5/0/00
A/6

DISK
DISK
TAPE
INITR

104
MB
209
MB
........

FX
FX
RM

DKB300
RZ11
DKB400
RZ12
DKB700
RZ15
...HostID...

B/3/0/00
B/4/0/00
B/7/0/00
B/6

DISK
RODISK
DISK
INITR

104
205
1.0

FX
RM
FX

Figure C–1

Example of the SHOW DEVICE Command

MB
MB
GB

RZ23
RZ24

RZ23
RRD40
RZ57

>>> SHOW DEVICE
VMS/VMB
------ESA0

ULTRIX ADDR
DEVTYP NUMBYTES
------ --------- -------SE0
08-00-2B-03-79-1F

RM/FX
-----

WP
--

DEVNAM
------

DKA300
RZ3
DKA400
RZ4
MKA500
TZ5
...HostID...

A/3/0/00
A/4/0/00
A/5/0/00
A/6

DISK
DISK
TAPE
INITR

104
MB
209
MB
........

FX
FX
RM

RZ23
RZ24

DKB300
RZ11
DKB400
RZ12
DKB500
RZ13
...HostID...

B/3/0/00
B/4/0/00
B/5/0/00
B/6

DISK
DISK
DISK
INITR

104
332
664

FX
FX
FX

RZ23
RZ55
RZ56

Figure C–2

Example of the SHOW DEVICE Command

MB
MB
MB

Appendix C C–1

>>> SHOW DEVICE
VMS/VMB
------ESA0

ULTRIX ADDR
DEVTYP NUMBYTES
------ --------- -------SE0
08-00-2B-03-79-1F

FX
FX
RM

WP
--

DEVNAM
------

RZ23
RZ24
RX23

DKA300
RZ3
DKA400
RZ4
DKA500
RZ5
...HostID...

A/3/0/00
A/4/0/00
A/5/0/00
A/6

DISK
DISK
DISK
INITR

...HostID...

B/6

INITR

Figure C–3

Example of the SHOW DEVICE Command

C–2 Appendix C

104
MB
209
MB
........

RM/FX
-----