Digital PDFs

EK-367AA-IC-002

1990

6 pages

Original

0.5MB

Document:	DECstation 5000 Model 200 Reference Card
Order Number:	EK-367AA-IC
Revision:	002
Pages:	6
Original Filename:

OCR Text

DECstation 5000 Model 200 Workstation Reference Card

PMAG-C

0
V~100-12

0 A 3.0
0 A 1.7

V~220-24

PMAD-A

V~100-1
20/
A 7.9/4.2
Hz 50-

WSE2R001

Table 1. Boot Commands
Command

Description

boot
boot 5/tz5/vmunix -a

Boots using the boot environment variable.
Boots the system software from the tape drive on the base
system SCSI connector set at SCSI unit 5.
Boots the system software from the optical compact disc drive
on the base system SCSI connector set at SCSI unit 0.
Boots the system software from the network.

boot 5/rz0/vmunix -a
boot 6/mop -a

Table 2. Configuration Display Commands
Command

Description

cnfg
cnfg 0
cnfg 1
cnfg 2
cnfg 5

Displays the general configuration for the base system.
Displays a detailed configuration for option slot 0.
Displays a detailed configuration for option slot 1.
Displays a detailed configuration for option slot 2.
Displays a detailed configuration for the SCSI connector in option slot
5.
Displays a detailed configuration for the ThinWire Ethernet connector
in option slot 6.
Displays a detailed configuration for the system and memory modules
in option slot 7.

cnfg 6
cnfg 7

Table 3. SCSI Commands
Command

Description

cnfg 5
init 5
t 5/target 5

Displays all SCSI devices attached to the base system SCSI controller.
Resets the SCSI devices attached to the base system SCSI controller.
Tests the unit on the base system’s SCSI controller set to SCSI
unit 5.
Tests the unit on the base system’s SCSI controller set to SCSI
unit 5. Allows write access during the test.

t 5/target 5 w

Table 4. System Commands
Command

Description

init
passwd

Resets the system.
Enters the current password to gain access to privileged console
commands.
Sets a new password. The password is in effect after the system is
reset.
Clears the existing password.
Tests the entire system.
Tests the base system.
Tests the hardware connected to option slot 0.
Tests the hardware connected to option slot 1.
Tests the hardware connected to option slot 2.
Tests the hardware connected to the SCSI connector (base slot 5).
Tests the cable connected to the ThinWire Ethernet connector (base
slot 6).

passwd -s
passwd -c
test
7/pst-t
0/pst-t
1/pst-t
2/pst-t
5/pst-t
6/pst-t

Table 5. Environment Variables
Command

Description

printenv
setenv variable value
unsetenv variable value

Displays the value of environment variables.
Sets the value of an environment variable.
Deletes an environment variable.
(continued on next page)

iii

Table 5 (Cont.). Environment Variables
Variable

Description

boot

The default bootpath specification. Possible values include
5/rz0/vmunix, 5/tz5, 6/mop, and 6/tftp.
Selects the level of self-test to be executed automatically.
Possible values are q for brief tests and t for more thorough
tests.
Specifies what action the console will perform upon powerup
or following a reset. Possible values are h = halt, r = restart
and b = bootstrap.
Specifies which device is to be used as the console terminal.
Value s = use printer port; value 0 = auto configure the
console.

testaction
haltaction
console

Use the communications adapter (H8571A) that comes
with the workstation to attach the console terminal to the
workstation.
Table 6. SCSI ID Switch Settings

ID Number

Hard Disk Drive
RRD40 Compact Disc Drive1
TZ30 Tape Drive2

TK50Z Tape Drive
TLZ04 Tape Drive3
RX23 Floppy Disk Drive
RX33 Floppy Disk Drive

7
6
5
4
3
2
1
0

Reserved
Up Up Down
Up Down Up
Up Down Down
Down Up Up
Down Up Down
Down Down Up
Down Down Down

Reserved
Down Down Up
Down Up Down
Down Up Up
Up Down Down
Up Down Up
Up Up Down
Up Up Up

1 Switch 4 on the RRD40 optical compact disc drive has no effect on the ID number.
2 Switch 1 (the left switch) on the TZ30 tape drive should always be in the up position. ID switch
settings listed for this drive start with switch 2.
3 Switch 1 (the left switch) on the TLZ04 tape drive should always be in the down position. ID

switch settings listed for this drive start with switch 2.

RRD40 optical compact disc drive
TKZ5OZ tape drive expansion

expansion box SCSI switches set

box SCSI switches set for

for ID number 4 (up down down).

ID numbers 5 (down up down).

Note that the position of the
fourth switch has no effect.

BA42 storage expansion box hard disk

TLZ04 tape drive expansion box

SCSI switches set for ID numbers

SCSI switches set for ID number

1 (down down up) on the left, and

5 (down up down beginning with the

0 (down down down) on the right.

second switch). The first switch

For SCSI switch settings for floppy

should always be in the down

disk and tape drives, see the BA42

position.

Installation Guide.

OPTIONS
P421

(2) RZ5
(1) RZ5

AC LINE

WSE2I133

RGB signal
cable connectors

Fuse

Power connector
R

Video cable

4
5

3
2

1
PMAG-C

0
V~100-120
A 3.0
V~220-240
A 1.7

PMAD-A

V~100-12
A 7.9/4

.2
Hz 50-6
0
W 359

0/220-240

14
13
12

10
9
8
7
1. Option slot 0 with a
color frame buffer
connector in place
2. Option slot 1

8. Keyboard-mouse connector
9. Communications connector
10. Communications connector

3. ThickWire Ethernet connector

11. Reset button

4. Cover-release screw

12. Diagnostic indicator lights

5. Monitor-to-system-unit power connector

13. ThinWire Ethernet connector

6. On/off switch

14. Small computer system interface

7. System unit power connector

(SCSI) connector
WSE2R002

EK-367AA-IC-002