Digital PDFs

EK-VS31M-MG-002

May 1990

137 pages

Original

3.3MB

Document:	VAXstation 3100 Model 76 Maintenance Guide
Order Number:	EK-VS31M-MG
Revision:	002
Pages:	137
Original Filename:	https://manx-docs.org/collections/mds-199909/cd1/vax/vs31mmg2.pdf

OCR Text

Order Number EK-VS31M-MG.002

Digital Equipment Corporation

First Edition, 1990
Second Edition, May 1991
FCC NOTICE: The equipment described in this manual generates, uses, and may emit
radio frequency energy. The equipment has been type tested and found to comply with
the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC
Rules, which are designed to provide reasonable protection against such radio frequency
interference when operated in a commercial environment. Operation of this equipment in
a residential area may cause interference, in which case the user at his own expense may
be required to take measures to correct the interference.
The following are trademarks of Digital Equipment Corporation: DEC, DEC/CMS, DEC
/MMS, DECnet, DECstation 5000, DECsystem-10, DECsystem-20, DECUS, DECwriter,
DIBOL, EDUSYSTEM, IAS, IVIS, MASSBUS, VAX, VAXcluster, PDP, RSTS, RX, ThinWire,
TK50, ULTRIX, ULTRIX-32, UNIBUS, VMS, VR160, VT, and the digital logo.
UNIX is a registered trademark of American Telephone & Telegraph Company.
Velcro is a trademark of Velcro USA, Inc.

This document was prepared and published by Educational Services Development and
Publishing, Digital Equipment Corporation.

Contents
About This Manual
1

Testing

1.1
Running Power-Up Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1.1
Power-Up Test Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2
Running a Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.1
Self-Test with Loopback Connectors . . . . . . . . . . . . . . . . . .
1.2.2
Self-Test Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3
Running System Exerciser Diagnostics . . . . . . . . . . . . . . . . .
1.3.1
System Exerciser Diagnostic Commands . . . . . . . . . . . . . .
1.3.2
System Exerciser Codes . . . . . . . . . . . . . . . . . . . . . . . . . . .

2
3
5
5
6
6
7
7

Troubleshooting

2.1
Troubleshooting Procedures . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2
TEST B — Memory (4 Mbyte DSIMM) . . . . . . . . . . . . . . . . .
2.2.1
Additional MEM Information . . . . . . . . . . . . . . . . . . . . . . .
2.3
SCSI-A Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.1
Running the System Exerciser . . . . . . . . . . . . . . . . . . . . .
2.3.2
Power Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . .

9
9
10
12
15
16

Utilities

3.1
Diskette Formatter Utility . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.1
Diskette Formatter Messages . . . . . . . . . . . . . . . . . . . . . . .
3.2
Special Diagnostic Key on Diskettes for Customer Service
System Exerciser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3
RX33 Formatting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4
Console Password Feature . . . . . . . . . . . . . . . . . . . . . . . . . . .

20
21
25
27
27
iii

iv Contents

3.4.1
Setting the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.2
Enabling the Password Feature . . . . . . . . . . . . . . . . . . . . .
3.4.3
Placing the Workstation in Privileged Mode . . . . . . . . . . .
3.4.4
Learning the Status of the Password Feature . . . . . . . . . .
3.4.5
Exiting Privileged Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5
Utility Differences for the Model 76 . . . . . . . . . . . . . . . . . . . .

29
30
30
31
31
31

VAXstation 3100 (Model 76) System

4.1
System Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2
FRU Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . .
4.2.1
System Box Cover Removal . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2
RZ22, RZ23, RZ23L, or RZ24 Disk Drive Removal . . . . . .
4.2.3
RX23 Disk Drive Removal . . . . . . . . . . . . . . . . . . . . . . . .
4.2.4
SCSI/FDI Adapter Removal . . . . . . . . . . . . . . . . . . . . . . . .
4.2.5
Drive Plate Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.6
Graphics Coprocessor Module Removal . . . . . . . . . . . . . . .
4.2.6.1
Graphics Coprocessor Module 60Hz/66Hz Selection . . . .
4.2.7
Memory SIMM Removal . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.8
System Module Removal . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.9
Internal SCSI Bus Data Cable Removal . . . . . . . . . . . . . .
4.2.10 Power Supply Removal . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.11 Keyboard Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.12 Mouse Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.13 Printer Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Recommended Spares List

Self-Tests

B.1 Console’s Configuration Display Utility (T 50) . . . . . . . . . . . .
B.2 NI (test 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2.1
TEST 1: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2.2
TEST 2: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2.3
TEST 3: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2.4
TEST 4: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2.5
TEST 5: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33
36
39
41
50
52
55
60
61
62
64
68
69
70
72
72

77
77
78
78
78
79
79

Contents v

B.2.6
TEST 6: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2.7
TEST 7: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.3 COLOR (test 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.4 SYS (test 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.5 SCSI-B (test 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.6 SCSI-A (test 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.7 IT (test 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.8 FP (test 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.9 MEM (test B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.10 DZ (test C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.11 NVR (test D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.12 CLK (test E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.13 MONO (test F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

System Tests

C.1
C.2
C.3
C.4
C.5
C.6
C.7
C.8
C.9

Error and Status Codes for the VS3100 System Test . . . . . . .
Ethernet Subsystem Status and Error Codes . . . . . . . . . . . . .
8-Plane Video Option Status and Error Codes . . . . . . . . . . . .
SCSI-B Status and Error Codes . . . . . . . . . . . . . . . . . . . . . . .
SCSI-A Status and Error Codes . . . . . . . . . . . . . . . . . . . . . . .
SCSI-A Error Explanations . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Status and Error Codes . . . . . . . . . . . . . . . . . . . . . .
DZ Controller Status and Error Messages . . . . . . . . . . . . . . .
Monochrome Display Status and Error Codes . . . . . . . . . . . .

Diagnostic LEDs Definitions

D.1

Additional LED Information . . . . . . . . . . . . . . . . . . . . . . . . .

Index

79
79
80
82
83
93
93
94
94
95
97
97
98

99
99
101
106
110
113
115
116
120

124

vi Contents

Examples
1–1
1–2
1–3
1–4
2–1
2–2
2–3
3–1
3–2
3–3

Power-Up Tests Screen Display . . . . . . . . . . . . . . . . . . . . . . .
Power-Up Tests with Errors . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration Table (T 50) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Running a Self-Test on a SCSI Bus . . . . . . . . . . . . . . . . . . . .
MEM Error Display in the Configuration Table . . . . . . . . . . .
Self-Test Results on the SCSI-A or SCSI-B Bus . . . . . . . . . .
System Exerciser Results for the SCSI-A Bus . . . . . . . . . . . .
Formatting an RX23 Diskette . . . . . . . . . . . . . . . . . . . . . . . .
PV_SCS_FMT_ERR# Error Code Breakdown . . . . . . . . . . . . .
Creating the Special Key on a Diskette . . . . . . . . . . . . . . . . .

2
2
4
5
11
13
16
21
23
26

Figures
2–1
3–1
4–1
4–2
4–3
4–4
4–5
4–6
4–7
4–8
4–9
4–10
4–11
4–12
4–13
4–14
4–15
4–16
4–17
4–18
4–19
4–20

Power Connector Pin Voltages on the System Module . . . . . .
Time-of-Year Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VAXstation 3100 Model 76 System Box . . . . . . . . . . . . . . . . .
FRU Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cover Screw Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing a Disk Drive from Position 1 . . . . . . . . . . . . . . . . .
Removing a Disk Drive from Position 2 . . . . . . . . . . . . . . . . .
Removing an RZ22/RZ23/RZ23L Disk Power and SCSI
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing Drive Module/Frame . . . . . . . . . . . . . . . . . . . . . . .
Setting the SCSI ID on the RZ22, RZ23, and RZ23L . . . . . .
Setting the SCSI ID on the RZ24 . . . . . . . . . . . . . . . . . . . . . .
Removing an RX23 Disk Drive . . . . . . . . . . . . . . . . . . . . . . . .
Removing an RX23 Disk Drive Power and SCSI Cables . . . .
SCSI ID Switch Location . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCSI/FDI Module Location . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Drive Plate . . . . . . . . . . . . . . . . . . . . . . . . . . .
External SCSI Access Panel . . . . . . . . . . . . . . . . . . . . . . . . . .
SCSI Terminator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the Drive Plate . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Graphics Coprocessor Module . . . . . . . . . . . . .

17
28
35
39
40
41
42
43
44
45
46
48
49
50
51
53
54
56
57
58
59
60

Contents vii

4–21
4–22
4–23
4–24
4–25
4–26
4–27
4–28
4–29
D–1

Removing the Graphics Coprocessor Module - Sectional View
Removing Memory Modules . . . . . . . . . . . . . . . . . . . . . . . . . .
System Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the System Module . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Ethernet ID ROM . . . . . . . . . . . . . . . . . . . . . .
Installing the System Module . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Internal SCSI Bus Data Cable . . . . . . . . . . . .
Power Supply Screw Locations . . . . . . . . . . . . . . . . . . . . . . .
Keyboard, Mouse, and Printer Removal . . . . . . . . . . . . . . . . .
LED Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

61
63
64
65
66
67
69
70
71
124

Tables
1–1
1–2
2–1
2–2
2–3
3–1
3–2
3–3
3–4
3–5
4–1
4–2
4–3
4–4
C–1
C–2
C–3
D–1

Power-Up and Self-Test Commands . . . . . . . . . . . . . . . . . . . .
System Exerciser Diagnostic Commands . . . . . . . . . . . . . . . .
Locating a Failed Memory SIMM . . . . . . . . . . . . . . . . . . . . . .
SCSI Devices Self-Test Status Codes . . . . . . . . . . . . . . . . . . .
System Module Power Connector Voltages . . . . . . . . . . . . . . .
Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diskette Formatter Messages . . . . . . . . . . . . . . . . . . . . . . . . .
T 76 Error Codes for the Diskette Formatter . . . . . . . . . . . . .
PV_SCS_FMT_ERR# Command Codes . . . . . . . . . . . . . . . . .
PV_SCS_FMT_ERR# Error Codes . . . . . . . . . . . . . . . . . . . . .
FRU Section Listings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RZ22, RZ23, RZ23L, and RZ24 Jumpers . . . . . . . . . . . . . . . .
SCSI/FDI Adapter Switch Settings . . . . . . . . . . . . . . . . . . . .
SCSI-B Error and Status Summary . . . . . . . . . . . . . . . . . . . .
SCSI Device Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCSI-A Error and Status Summary . . . . . . . . . . . . . . . . . . . .
Diagnostic LEDs Definitions . . . . . . . . . . . . . . . . . . . . . . . . .

3
8
12
14
18
19
21
22
23
24
37
38
47
52
108
109
112
121

About This Manual
This guide describes how to troubleshoot, adjust, and repair the
VAXstation 3100 Model 76 system to the field replaceable unit (FRU)
level. It covers all FRU options presently available for the VAXstation
3100 Model 76 system. The label on the rear of the system box indicates
the system you are working on (VS43A-xx).

Organization
This guide has four chapters and four appendices.
Chapter

Description

Describes testing procedures for a power-up test, self-test, and
system exerciser tests.

Describes troubleshooting procedures to help isolate the
problem to an FRU.

Provides a description of the utilities.

Describes the Model 76 system, gives a system overview, and
outlines FRU removal and replacement procedures.

Appendix A

Lists the recommended spares list (RSL).

Appendix B

Lists the self-tests.

Appendix C

Lists the system tests.

Appendix D

Lists Diagnostic LED Definitions.

Intended Audience
This document is for Digital Customer Services personnel and selfmaintenance customers only.

x About This Manual

Tools and Equipment
The following tools are needed to service the VAXstation 3100 Model 76.
Tools and Equipment

Part Number

Screwdriver (flat-head)

47-00043-03

Screwdriver (Phillips)

47-00043-04

Wriststrap and antistatic mat (included in Customer Services
antistatic kit)

29-26246-00

Related Documents
The following documents can be ordered from Digital. This guide refers to
many of these documents.
Documents

Order Number

BA42 Expansion Box Maintenance Guide

EK-BA42A-MG

RX23 Diskette Drive Service Manual

EK-RX23D-SV

RZ Series Disk Drive Subsystem Pocket Service Guide

EK-RZXXD-PS

RZ22 and RZ23 Disk Drive Service Manual

EK-RZ223-SV

RZxx Disk Drive Subsystem Pocket Service Guide

EK-RZXXD-PS

RZ22/23/24 Diskette Drive Service Manual

EK-RZ234-SV

RZ24 Pocket Service Guide

EK-RZ24D-PS

RZ55 Disk Drive Service Manual

EK-RZ55D-SV

RZ55 Pocket Service Guide

EK-RZ55D-PS

RZ56 Disk Drive Service Manual

EK-RZ56D-SV

RZ56 Pocket Service Guide

EK-RZ56D-PS

VAXstation 2000, MicroVAX 2000, VAXmate Network Guide

EK-NETAB-UG

VAXstation 3100 Maintenance Guide

EK-285AA-MG

VAXstation 3100 Model 76 Owner’s Manual

EK-VX31M-UG

VAXstation 3100 Model 76 Upgrade Guide

EK-VX31M-CG

VR150 Pocket Service Guide

EK-VR150-PS

About This Manual xi

Documents

Order Number

VR160 Pocket Service Guide

EK-VR160-PS

VR262 Pocket Service Guide

EK-VR262-PS

VR299 Pocket Service Guide

EK-VR299-PS

VR297 Service Manual

EK-VR297-SG

VRT13 Service Manual

ER-VRT13-SM

VRT19 Service Manual

ER-VRT19-SM

VS3100 Maintenance Guide Addendum: Models 38 and 46

EK-344AA-AD

Workstations Network Guide

EK-VS315-GD

WS01X-GA/GB Graphics Coprocessor Maintenance Guide

EK-WS01X-MS

Digital personnel may order the documents listed from:
Digital Equipment Corporation
444 Whitney Street
Northboro, MA 01532
Attn: Publishing and Circulation Services (NRO2-2)
Order Processing Section

Conventions
This document uses the following conventions:
Convention

Meaning

Key

A terminal key used in text and examples. For
example, Break indicates that you press the Break
key on your terminal keyboard.

NOTE

Provides general information.

CAUTION

Provides information that prevents damage to
equipment and software.

WARNING

Provides information to prevent personal injury.

1
Testing
This chapter provides an overview of the testing procedures for the
VAXstation 3100 Model 76 system. Since the testing procedures for the
VAXstation 3100 Model 76 are similar to the testing procedures for
the previous VAXstation 3100 models, this chapter will not repeat the
information described in Chapter 1 of the VAXstation 3100 Maintenance
Guide. If you are not familiar with the diagnostics available on the
VAXstation 3100 Model 76 system, you should read through the testing
procedures in Chapter 1 of the VAXstation 3100 Maintenance Guide. Also
refer to the WS01X-GA/GB Graphics Coprocessor Maintenance Guide.
The label on the back of the system box indicates which model you are
working on. The VS43A-xx model number on the label identifies the
VAXstation 3100 Model 76 system.
All testing is performed while in the console mode and diagnostic tests
are ROM-based.
This chapter contains an overview of the following procedures:
•

Running power-up tests

•

Running self-tests

•

Running system exerciser diagnostics

CAUTION
Do not remove or unplug the keyboard, mouse, printer, or
terminator without turning the power OFF. If the system is up
and running, use the proper shutdown procedure prior to halting
the system.

2 Testing

1.1 Running Power-Up Tests
Power-up tests run each time you turn the system power ON and, if the
tests are successful, the operating system starts booting. Power-up testing
consists of a sequence of tests executed for each device installed in the
system. The test number of each device is listed on the power-up screen
display as the device is tested.
To run power-up tests, turn the system power switch ON.
Example 1–1 shows an example of the power-up screen display.
KA43-A

V1.0

F...E...D...C...B...A_..9...8...7...6...5...4...3_..2_..1...
OK
>>>

Example 1–1

Power-Up Tests Screen Display

Example 1–2 shows the power-up screen display with a hard error found
in TEST 9 and a soft error in TEST 8.
KA43-A

V1.0

F...E...D...C...B...A_..9?..8...7...6...5...4_..3_..2_..1...
?? 9
? 8

00B0
0040

Example 1–2

0001.F002
0000.0005

(Hard error)
(Soft error)

Power-Up Tests with Errors

Usually, a question mark (?) in the power-up summary indicates a soft
error and the system may be usable without replacing any FRUs.
Double question marks (??) in the power-up summary indicates a hard
error. This indicates a serious problem that may affect the normal
operation of some component in the system. The failing device must
be replaced before booting the operating system software.
If no power-up display is seen, refer to the VAXstation 3100 Maintenance
Guide.

Testing 3

1.1.1 Power-Up Test Codes
The power-up test codes indicate no error, soft errors, status information,
or hard (fatal) error information. Any errors found by power-up tests are
listed in the power-up tests summary. These errors, as well as the status
of all devices installed in the system, are then stored in the configuration
table (T 50). Refer to Example 1–3 for an example of the configuration
table.
Table 1–1 lists the test numbers and the devices that are tested during
that particular test. To look at the status of a device, display the
configuration table.
>>> TEST 50

The configuration table lists every device in the system and also lists
the results of the power-up tests and self-test. The configuration table
is updated each time a self-test is run (mouse status is not updated).
Remember that the configuration table contains the results of the powerup tests and self-test, and not the results of the system exerciser.
Table 1–1 Power-Up and Self-Test Commands
Test

Mnemonics

Device

MONO

Base video

CLK

Time-of-year clock

NVR

Nonvolatile random access memory (RAM)

Serial line controller

MEM

Memory

Floating point unit

Interval timer

SCSI-A

SCSI-A bus controller
Internal RX23/SCSI adapter assembly
Internal RX33/SCSI adapter assembly
Internal RZ22, RZ23, and RZ24 disk drives

4 Testing

Table 1–1 (Cont.) Power-Up and Self-Test Commands
Test

Mnemonics

Device

SCSI-B

SCSI-B bus controller
RRD40 storage expansion box
RZ55 storage expansion box
RZ56 storage expansion box
RZ57 storage expansion box
TK50 storage expansion box
TZ30 in storage expansion box

SYS

Interrupt controller and Ethernet ID ROM

8PLN

Option module (GPX 8-plane graphics module
or SPX ScanProc 8-plane graphics module)

Option module (not available)

Ethernet circuits

Example 1–3 shows an example of the configuration table.
>>> TEST 50
KA43-A
V1.0
ID 08-00-2B-02-CF-A4
MONO
0000.0001
CLK
0000.0001
NVR
0000.0001
DZ
0000.0001
00000001 00000001 00000001 00000001 00000001 000012A0
MEM
0008.0001
00800000
FP
0000.0001
IT
0000.0001
SCSI-A
0808.0001 V1.0
FFFFFF05 FFFFFF05 FFFFFF05 00000001 FFFFFF05 FFFFFF05 FFFFFF03
SCSI-B
3C3C.0001 V1.0
FFFFFF05 FFFFFF05 00000001 00000001 05000001 01000001 FFFFFF03
SYS
0000.0001
8PLN
0000.0001 V1.0
NI
0000.0001
>>>

Example 1–3

Configuration Table (T 50)

Testing 5

Any code in the configuration table other than 0000.0001 on the MONO,
DZ, FP, IT, or SYS devices indicates a hard error and the system module
must be replaced for proper operation of the system. The other devices
such as CLK, NVR, MEM, SCSI-A, SCSI-B, and NI may have a code other
than (0000.0001) and may still operate normally.

1.2 Running a Self-Test
Self-test allows you to test every device again after the power-up tests are
complete. Devices can be tested individually (except for drives), a few at a
time, or all of them sequentially just like power-up tests.
To individually test a device (drives are tested all together on their
particular bus), enter the word (TEST) or just the letter (T), followed by
a space and the test number of the device you want tested. Table 1–1
lists the devices and the test numbers that test the devices. Example 1–4
shows an example of running a self-test on a SCSI bus. All devices
connected to the SCSI bus are tested and the results are listed in the
configuration table (T 50).
>>> TEST 6
6...
>>>
NOTE: Enter TEST 50 to see the results

Example 1–4

Running a Self-Test on a SCSI Bus

1.2.1 Self-Test with Loopback Connectors
A customer mode self-test (that is, without any serial line loopbacks)
does not test the drivers on the serial lines (DZ). To test the DZ drivers,
run a self-test on the serial lines in customer service mode by installing
loopbacks on the two MMJ connectors, then run TEST C. Display the
configuration table to see the results.
If only one MMJ loopback is available, install it in the communications
port and run the tests. An error code of 0000.0200 on the fourth line
for the DZ indicates that the printer port does not have the loopback
installed, but the communications port tested successfully.

6 Testing

NOTE
The ThinWire Ethernet port or the standard Ethernet port
(depending on which port the customer is using) on the back
of the system box must be terminated properly when running
diagnostics on the Ethernet circuits (TEST 1). Otherwise, an
error code of 0000.7001 or greater is listed in the configuration
table. The Ethernet port and SCSI port must always either be
terminated or have an expansion box connected.

1.2.2 Self-Test Codes
If an error is detected during a self-test, a question mark (?) is put next
to the test number and a failure message (84 FAIL) is displayed. You
must display the configuration table (enter TEST 50) after a self-test is
complete to see the error code.
The self-test error codes are located in Appendix B.

1.3 Running System Exerciser Diagnostics
The system exerciser simulates a worst-case operating system situation
test for each device, and checks how the device operates under these
conditions. This type of testing usually finds any interactive problems.
To run the customer service mode system exerciser, perform the following
steps:
1. Install a loopback on the communication port.
2. Insert and load the special-keyed test diskette, compact test disk, and
tape cartridge.1
3. Enter TEST 101, TEST 102, or TEST 80000106.
TEST 80000106 allows you to enter the test number of the individual
devices you want to run the exerciser on. If the diskette or the tape
drive are not loaded with the special-key media, the system exerciser
does not do destructive writes to them, and tests them the same way
as it does during the customer mode system exerciser. If the compact
disk drive is not loaded with the test disk, the drive does not perform
any reads. If the test disk is not available, any disk loaded allows
the exerciser to perform reads but does not check the error correction
circuits (ECC).

This special key on the media prevents the exerciser from accidentally destroying
data on the customer’s diskette or tape cartridge. The compact disk never does
write testing, only reads.

Testing 7

Refer to Chapter 3 of this guide for information on creating the special
diagnostic keys on the diskette and tape.

1.3.1 System Exerciser Diagnostic Commands
Table 1–2 lists the system exerciser diagnostic commands. When running
TEST 0 or TEST 101, the exerciser automatically stops after about 5
minutes and the HALT message (06 HLT INST) is displayed. This HALT
message is normal for these two tests.

1.3.2 System Exerciser Codes
The system exerciser displays the status of the devices on the screen as
the exerciser is running. Any errors found are displayed in the exerciser
display. When examining the exerciser display, a question mark (?) in the
far left column indicates a soft error, double question marks (??) indicate
a hard error, and the absence of question marks usually indicates success.
There may be times when there are no question marks, but a drive may
not be listed in the display (for example, an unplugged power cable). In
these instances you need to be familiar with the codes of all devices so
that when you examine the display, you know if a specific drive or device
is listed, and if the drive or device has a fault.
The system exerciser codes are located in Appendix C.

8 Testing

Table 1–2 System Exerciser Diagnostic Commands
Test

Description of Commands

Runs customer mode system exerciser. No loopback
connectors are needed. Removable media must be loaded
in the RX23 disk drive for the exerciser to recognize the
drive. The TZ30 does not require media to be loaded. The
exerciser tests each device once sequentially, then tests them
simultaneously, and stops when the slowest device finishes
(about 5 minutes).

T 1011

Runs customer service mode system exerciser. Loopbacks
and removable media are required. It exercises each device
once sequentially, then exercises them simultaneously, and
stops when the slowest device finishes (about 5 to 8 minutes).
Do not stop the exerciser before it is finished.

T 102

Runs customer service mode system exerciser. Loopbacks
and removable media are required. It exercises each device
once sequentially and then exercises them simultaneously
until you press CTRL C to terminate the tests. Note that
the exerciser takes up to 30 seconds to stop after you press
CTRL C . Do not stop the exerciser until every device is
exercised twice (second pass). Also, do not press the Halt
button to stop the exerciser. Once the tests are terminated,
an extended summary for only the SCSI-A and SCSI-B tests
can be displayed by pressing Return . Continue pressing
Return to redisplay the extended summaries. Press CTRL C
a second time to terminate the extended summary which will
bring you back to the console prompt >>>.

T 800001062

Used for individual device testing. Loopbacks and removable
media are required. Runs system exerciser diagnostics on
individual devices (TEST 6 and TEST 7 are considered
individual devices even though they test several drives).
This test allows you to test individual devices by entering
the test number of the device at a second prompt. This
individual testing saves time since you do not have to wait
for all of the other devices to finish testing.

1 The errors for these tests are only displayed on the screen.
2 There is no system exerciser test in Memory Test B.

If
>>>T80000106
?>>>B
is selected, you must hit the Halt button on the rear of the system to get back to the
console mode.

2
Troubleshooting
This chapter contains information for troubleshooting the new devices
available on the VAXstation 3100 Model 76 system. The label on the back
of the system box indicates that you are working on the
VS43A-xx. All troubleshooting procedures are performed while in console
mode (operating system software halted).

2.1 Troubleshooting Procedures
This section contains troubleshooting information for the devices listed
below.
•

4 Mbyte memory DSIMM (Section 2.2)

•

RX23 disk drive with the SCSI/FDI adapter module (Section 2.3)

2.2 TEST B — Memory (4 Mbyte DSIMM)
The diagnostics used for the 4 Mbyte memory DSIMM test all of the main
memory in the system. Therefore, any error for the memory must be
deciphered to determine which DSIMM contains the error. There may be
more than one module containing the error.
Running a Self-Test
A self-test performs a complete check of the memory in the system. The
results are stored in the configuration table (T 50). To run a self-test:
1. Enter TEST B.
2. Enter TEST 50 to see the results.

10 Troubleshooting

Self-Test Results
A code of 00XX.0001 next to the MEM mnemonic indicates no errors
(the XX is the total amount of memory installed in the system [in
hexadecimal]). Verify that the mnemonic matches the amount of memory
in the system.
If an error is detected, refer to Section 2.2.1 to determine which module
needs to be replaced. There is no further memory test in the system
exerciser. The self-test will run complete memory tests if you:
1. Install a loopback on the communication port.
2. Enter TEST B.
3. Read the results on the screen during the test.
A code of 0XXX.0001 next to the MEM mnemonic indicates no errors (the
XXX is the number of pages of memory tested during the last pass of the
exerciser [1 page = 512 bytes]).
The following test will not work on this system:
>>> t 80000106
?>>> B

If this test is invoked, the system will have to be halted in order to get
control in console mode again. If the DZ drivers were also invoked,
CTRL C does not get you back to the console mode.

2.2.1 Additional MEM Information
The code for MEM in the configuration table indicates the amount of
memory available if no errors are detected. For example, 0010.0001
indicates that 16 Mbytes of memory are available (10 in hexadecimal =
16). The second MEM line in the configuration table contains two 8-digit
codes, one of which is displayed when errors are detected. The first
code repeats the amount of memory in the system, and the second code
(displayed only if an error is detected) contains the location of the failed
memory.
There may be up to six more 8-digit codes listed in the configuration
table. These codes represent the cache memory located on the system
module. If this is seen, run the memory test again to see if the results
are duplicated. If so, the cache is bad and the system module has to be
replaced.

Troubleshooting 11

Example 2–1 shows the second 8-digit number of the MEM display in
the configuration table. Each digit represents a SIMM memory module.
A code other than 0 in any of the digits indicates an error on a memory
SIMM.
Each digit contains the status of four banks of memory (1 bank = 1 Mbyte
of memory).
4−Digit Error Code

?? MEM

0010.0020
01000000 00000000

Bit map representation of the failed
memory bank on a memory module if not
all zeros (0000000).
See Table 2−1 to determine the
failed SIMM memory module.
This field is displayed only when a failure
is detected on one of the SIMM modules.

8−Digit Error Code
Hexadecimal representation of the
total amount of memory in the system
as listed below.
00400000
00800000
00C00000
01000000
01400000
01800000
01C00000
02000000

Example 2–1

4 Mbytes
8 Mbytes
12 Mbytes
16 Mbytes
20 Mbytes
24 Mbytes
28 Mbytes
32 Mbytes

MEM Error Display in the Configuration Table

12 Troubleshooting

Table 2–1 lists the location of each memory SIMM and contains possible
failure codes.
Table 2–1 Locating a Failed Memory SIMM
Memory Module
Configurations

8-Digit Error Code for MEM

SIMM Callout on
System Module

SIMM 1

SIMM 2

SIMM 7

SIMM 8

SIMM 3
SIMM 4
SIMM 5
SIMM 6

0
0
0

0
0

1 A 0 in this SIMM location means this SIMM is good. Anything from 1 through F indicates

this SIMM is failing. For example; a code of 00004000 indicates that the SIMM, numbered 4
on the etch of the system module, is bad.

2.3 SCSI-A Troubleshooting
SCSI-A is the internal SCSI bus. To test the internal SCSI bus, execute
test 7. You will find only half-height hard disk and/or half-height 3.5-inch
floppy drives internal to the system.
In the following procedure an RX23 is discussed. The procedure for
troubleshooting the RX23 disk with the SCSI/FDI adapter module is the
same as troubleshooting the other drives on the SCSI bus. Remember
that the device name of the RX23 drive is usually DKA500. The 5
indicates the SCSI ID and the A indicates the RX23 is on the SCSI-A
bus.
The diagnostics used to test the RX23 drive and the SCSI/FDI adapter
module are the self-test and the system exerciser.

Troubleshooting 13

Running a Self-Test
A self-test performs an inquiry of the drive and reports the status of
the drive and the SCSI adapter module. No read/write operations are
performed. The results are stored in the configuration table (T 50). To
run a self-test:
1. Enter TEST 7.
2. Enter TEST 50 to see the results.
Self-Test Results
A code of 00000001 in the sixth position (if RX23 is at SCSI ID 5) in
the SCSI-A bus status line indicates no errors. Example 2–2 shows an
example of SCSI-A bus codes in the configuration table.
If any errors are detected, one or two question marks are flagged in the
left column next to the SCSI-A mnemonic.
SCSI-A 2C2C.0001
FFFFFF05 FFFFFF05

off_line

Controller
Drive
Drive
Drive
00000001 00000001 FFFFFF05 00000001 FFFFFF03

RZ23
Drive

off_line

RX23
Drive

SCSI-A
Controller

FFFFFF05...

off_line
LJ-00735-TI0

Example 2–2

Self-Test Results on the SCSI-A or SCSI-B Bus

If a Self-Test Indicates an Error
The error may be on the RX23 drive, on the other drives on the SCSI-A
bus, or on the SCSI-A bus controller. To determine which device is faulty,
examine the status codes of the individual drives. The SCSI IDs are
numbered 0 through 7 from left to right (for example, the RZ23 disk drive
is located at SCSI ID 2 and the RX23 disk drive is located at SCSI ID 5).
Table 2–2 lists the normal status codes for each SCSI device available on
the SCSI bus.

14 Troubleshooting

Any code other than those listed indicates an error in the device at that
SCSI ID.
Table 2–2 SCSI Devices Self-Test Status Codes
Status Code

SCSI Device

FFFFFF05

Device is off-line or not installed at this SCSI ID
If a drive’s status code indicates FFFFFF05, check the drive’s
cabling and power, then retest. If the code is still FFFFFF05
after retesting, replace the drive

FFFFFF03

SCSI bus controller

FFFFFFFF

Device not tested - possible SCSI bus controller error

00000001

RX23 SCSI/FDI adapter assembly or

Disk Drive

Tape Drive

RZ22

TK50

RZ23

TLZ04

RZ23L

TZK10

RZ24

—

RZ55

—

RZ56

—

RZ57

—

RX33

—

01000001

TZ30 tape drive

05000001

RRD40 compact disk drive

Troubleshooting 15

2.3.1 Running the System Exerciser
The system exerciser performs a more thorough test of the RX23 disk and
the SCSI adapter module. It performs a read/write operation during the
second pass of the exerciser when the special-keyed test diskette is loaded
in the RX23 drive before starting the system exerciser. To run the system
exerciser:
1. Install a loopback on the communication port.
2. Load the special-keyed test diskette in the RX23 drive. If the diskette
does not contain the special key, go to Section 3.2 and perform the
procedure to write the special key on the diskette.
3. Enter TEST 80000106 Return .
? >>> 7 Return .
4. Read the results on the screen during the test.
5. Press the Halt button to stop the exerciser.
System Exerciser Results
A code of 5300.0001 listed under the SCSI-A bus indicates that there are
no errors for the RX23 and that the read/write operation is successful.
A code of 5100.0001 listed under the SCSI-A bus indicates that there are
no errors. However, a no write operation took place either because the
exerciser is still executing the first pass, or the special key is not found on
the diskette, or no diskette is loaded.

16 Troubleshooting

Example 2–3 shows the system exerciser display for the SCSI-A bus.
There is one line for the status of the SCSI-A controller on the system
module, and one line for each of the drives installed on the SCSI-A bus.
The status of the SCSI controller is next to the SCSI-A mnemonic (first
line), and the status of each drive is listed under the controller’s code
(separate line for each drive).
7

80A0

SCSI−A

Example 2–3

6000.0001
2200.0001
3200.0001
5300.0001

0000

0 00:05:26
RZ23 disk drive
RZ23 disk drive
RX23/SCSI adapter

System Exerciser Results for the SCSI-A Bus

If an Error is Detected
If there are any question marks (?) on the SCSI controller’s status line,
the SCSI controller is probably faulty and must be replaced.
If there are any question marks on a drive’s status line, the problem could
be in either the drive, the SCSI bus cabling, the SCSI bus terminator,
or the SCSI controller. For example, an error that is listed in the drive’s
code may be a data transfer error and does not isolate the problem to the
device itself; it may still be in the SCSI controller.

2.3.2 Power Connector Pinouts
Figure 2–1 illustrates the pinout locations for the power connector which
are located on the system module. See Table 2–3 for system module power
connector voltages.

Troubleshooting 17

11 12 13

LJ-00687-TI0

Figure 2–1

Power Connector Pin Voltages on the System Module

18 Troubleshooting

Table 2–3 System Module Power Connector Voltages
Pin Number

Voltage

Tolerance

Color

– 12.1 Vdc

Blue

Ground

—

Black

Ground

—

Black

Ground

—

Black

+5.1 Vdc

Red

+5.1 Vdc

Red

+3.5 to +5.25 Vdc

—

Brown

+5.1 Vdc

Red

+12.1 Vdc

Orange

+5.1 Vdc

Red

Ground

—

Black

Ground

—

Black

Yellow

—

White

– 9 Vdc

– 9 Vdc return

1 Measurement made with negative lead connected to pin 14
2 Ground for the –9 Vdc supply (an isolated supply)

3
Utilities
This chapter describes the new utilities available on the VAXstation 3100
Model 76. Table 3–1 lists all the utilities available on the VAXstation
3100 Model 76 system.
Table 3–1 Utilities
Test Number

Utility Invoked

T 50

Configuration table (also displays the Ethernet hardware
address, for example; ID 08-00-2B-02-CF-A4)

T 51

Sets NVR default boot device

T 52

Sets NVR default boot flags

T 53

Sets NVR default recovery action flags

T 54

Sets keyboard language

SHO ESTAT

Shows system exerciser extended summary

T 60

Alignment circle and crosshatch (monochrome monitor, no
graphics module installed)

T 61

Monochrome screen of Es (no graphics module installed)

T 62

Monochrome white screen (no graphics module installed)

T 73

Special key on tapes for customer service mode system
exerciser

T 74

Special key on diskettes for customer service mode system
exerciser

T 75

SCSI disk data eraser

T 76
T 80

Diskette formatter
1

Circle-crosshatch (color monitor)

1 Will work only with an SPX or GPX 8-plane graphics module installed.

20 Utilities

Table 3–1 (Cont.) Utilities
Test Number

Utility Invoked

T 811

Screen of all Es (color monitor)

T 821

White screen (color monitor)

T 831

4-bar color bar (color monitor)

T 84

Red screen (color monitor)

T 85

Green screen (color monitor)

T 86

Blue screen (color monitor)

T 87

8-bar color bar (color monitor)

T 88

Gray scale (color and monochrome monitors)

1 Will work only with an SPX or GPX 8-plane graphics module installed.

3.1 Diskette Formatter Utility
This utility formats RX23 diskettes. The command to start the formatter
is TEST 76. Example 3–1 shows an example of running the formatter on
a DKA500 (RX23).
CAUTION
Formatting destroys all user data on the diskette.

Utilities

>>> TEST 76
ScsFlpFmtter
PV_SCS_FMT_CHN

(0=SCSIA \ 1=SCSIB)? 0

Enter SCSI bus.

PV_SCS_FMT_ID

(0,1,2,3,4,5,6,7)? 5

Enter SCSI ID of RX23.

PV_SCS_FMT_RUsure (1/0)? 1

Enter a 1 for yes, 0 for no.

PV_SCS_FMTing...

Formatting diskette.

PV_SCS_FMT_CHKpass..........

RX23 format checked OK.

PV_SCS_FMT_SUCC

Diskette is formatted
successfully.

>>>

Example 3–1

Formatting an RX23 Diskette

3.1.1 Diskette Formatter Messages
Table 3–2 lists all the formatter messages and gives an explanation for
each.
Table 3–2 Diskette Formatter Messages
Formatter Message

Explanation

PV_SCS_FMT_CHKpass

A check pass is being done on the diskette.

PV_SCS_FMT_CHN

Enter the SCSI bus that is connected to
the RX23/SCSI adapter assembly. Enter
0 for the SCSI-A bus or enter 1 for the
SCSI-B bus.

PV_SCS_FMTing

The RX23 diskette is being formatted.

PV_SCS_FMT_RUsure

The formatter uses this question as a
safety check. Enter 1 for yes if you want
to format the diskette, otherwise, enter
any character other than 1 to abort the
formatter.

22 Utilities

Table 3–2 (Cont.) Diskette Formatter Messages
Formatter Message

Explanation

PV_SCS_FMT_ID

Enter the SCSI ID of the RX23. Usually
the RX23 ID is set for ID 5.

PV_SCS_FMT_SUCC

The diskette has been successfully
formatted.

PV_SCS_FMTex

The RX23 formatter has been aborted.

PV_SCS_FMT_ERR#

The formatter has been stopped because of
the error code indicated by the pound sign
(#). Table 3–3 lists the error codes.

Table 3–3 lists all the T 76 error codes and gives a description for each.
Table 3–3 T 76 Error Codes for the Diskette Formatter
Code

Description

Wrong SCSI bus or SCSI ID entered1

SCSI command error1

Medium error. A read or write failed1

Unit not ready. No media

Illegal device type1

SCSI bus hung after reset attempt1

Data compare error

1 See the section Determining the Problem for more details.

Determining the Problem
An 8-digit error code may be listed under the PV_SCS_FMT_ERR#
error message. If this 8-digit error code is listed, you can determine
which command was sent to the RX23 and why the command failed.
Example 3–2 shows the 8-digit error code breakdown.

Utilities

PV_SCS_FMT_ERR 2
03000006

Error code
Always zeros
Command code

Example 3–2

PV_SCS_FMT_ERR# Error Code Breakdown

Table 3–4 lists the command codes for the 8-digit error code listed under
the PV_SCS_FMT_ERR# error message.
Table 3–4 PV_SCS_FMT_ERR# Command Codes
Command Code

Command Sent to Device

Test Unit Ready

Request Sense

Format_Unit

Read

Write

Inquiry

Mode Select

Mode Sense

Start Unit

Read Capacity

No Command

Table 3–5 lists the error codes for the 8-digit error code listed under the
PV_SCS_FMT_ERR# error message.

24 Utilities

Table 3–5 PV_SCS_FMT_ERR# Error Codes
Error
Code

Description of Code

Bad status returned by device

Not enough sense data returned

Bad sense key returned by device

Too many retries of this command, failed after request_sense

Attempt to select host

No req was received within timeout period

Entered the same phase twice

Device in the command phase is out of order

Device in the data_in phase is out of order

Unexpected entry in the data_in phase (the command should not
go in the data_in phase at all)

Device in the status phase is out of order

Device in the message_in phase is out of order

Device in the data_out phase is out of order

Unexpected entry in the data_out phase (the command should not
go in the data_out phase at all)

Entry in unsupported phase 4

Entry in unsupported phase 5

Device has not signaled a phase

No data transferred when receiving bytes

AIP bit not set soon enough

Selection failed

Too many REQs

Timeout waiting for bus after command (req is not set)

Not enough inquiry data returned by device

Reset did not clear bus

Attempt to access SCSI-B on ST506 board

Unexpected message_out phase

Utilities

Table 3–5 (Cont.) PV_SCS_FMT_ERR# Error Codes
Error
Code

Description of Code

Too many retries of this command, failed after bus_device_reset

Timeout waiting for bus free after command (req is set)

No interrupt request for the DMA_in phase

SCD_CNT not zero following DMA_in phase

No interrupt request for the DMA_out phase

SCD_CNT wrong following DMA_in phase

Phase did not change soon after data_xfer_in phase

Phase did not change soon after data_xfer_out phase

Parity error on SCSI bus

SCSI req was not set in time

SCSI req was not cleared in time

3.2 Special Diagnostic Key on Diskettes for
Customer Service System Exerciser
The diskette in the maintenance kit must have a special diagnostic code
written on it to allow the system exerciser to write on the diskette when
running in the customer service mode. Without this special key, such
as on normal customer diskettes, the system exerciser does not perform
write testing on the diskette. This safety feature prevents accidentally
destroying the customer’s programmed diskettes.

26 Utilities

TEST 74 creates a special key on the diskette. First, the diskette in the
maintenance kit must be formatted using the T 76 command (described in
Section 3.1). Secondly, the diskette must have the special diagnostic key
written on it before it can be used with the customer service mode system
exerciser.
Example 3–3 shows a successful example of creating a special-keyed
diskette.
>>> TEST 74
KA42 Flmker
VSflmk_QUE_port (A,B) ? A

Enter SCSI bus port.

VSflmk_QUE_id (0,1,2,3,4,5,7) ? 5

Enter ID address of drive.

vsflmk_que_rusure (1/0) ? 1

Enter 1 for yes, 0 for no.

vsflmk......... ok

Keyed successfully.

>>>

Example 3–3

Creating the Special Key on a Diskette

If any errors occur while running TEST 74, ensure that the drive is online and operating properly, then run the special-key command again.
Also ensure that the diskette was originally formatted using the T 76
command.

Utilities

3.3 RX33 Formatting
Perform the following commands to format an RX33 diskette. When
executing a command, an error may occur. If an error occurs, try
executing the command again, then proceed to the next steps. The first
two commands will execute while under the VMS operating system.
To format an RX33:
1. $ Init/Density = Double
2. $ Shutdown
3. Press halt button when prompted to do so.
4. >>> Test 74

3.4 Console Password Feature
The VAXstation 3100 workstations have a console password feature that
allows the PVAX to be configured such that a console password must be
entered before a user can do an interactive boot. The password and the
configuration are stored in nonvolatile memory.
If a user enables this feature and then forgets his console password,
the only way to regain full access to the workstation is to perform the
following:
1. Open the system box
2. Interrupt the battery-power to the nonvolatile memory by doing the
following:
NOTE
The chip is socketed and has a white drawing of an alarm
clock on it.
a. Use a small screwdriver or ROM puller to remove the Time-of-Year
(TOY) chip (refer to Figure 3–1).

28 Utilities

TOY Clock
Key

TOY Clock

MA-1329-90.DG

Figure 3–1

Time-of-Year Chip

CAUTION
Leaving the battery on a conductive surface for a period of
time greater than 1-3 seconds may cause premature battery
failure.
b. Place the leads to the chip on top of the system power supply for
1-3 seconds.
c.

Replace the TOY chip. The TOY clock key should be towards the
rear of the system module.
This effectively shorts the battery internal to the TOY clock and
resets the password to the disabled mode.

3. If you do not want to enable the console password feature stop here.
Do not proceed to the next step.

Utilities

4. To enable the console password feature:
a. Set a password with the command SET PSWD .
b. Enable the password feature with the command SET PSE 1 .
Use of these commands is further explained in the next two
sections.

3.4.1 Setting the Password
Use the SET PSWD command to select a new password. SET PSWD is a
privileged command. The form of the command is:
>>> SET PSWD

After you invoke the command, the console prompts for a password as
follows:
1 >>>

Enter the new password and press Return . Note that the console does not
display the password as you enter it.
The password must be a hexadecimal string of characters (0 through 9
and A through F) with a length of exactly sixteen characters. If the string
contains a nonhexadecimal character or is of the wrong length, the SET
PSWD command fails and the following error message is displayed:
?31 ILL PSWD

Some valid passwords are:
1ACED33BD23AF301
DAC324EABEA222EA
111111111AACCDEE

Invalid passwords include:
FACE

(not 16 characters long)

442ED2FFAC213SE2

(contains S, an illegal character)

If the password character string is of the right length, the console prompts
you to reenter the new password in order to verify that it is correct:
2 >>>

30 Utilities

Reenter the new password and press Return . Again, note that the
password is not displayed. If the verification password matches exactly
the password you first entered, then it becomes your new password. If
the two passwords do not match, then the command fails and the console
displays the following error message:
?31 ILL PSWD

3.4.2 Enabling the Password Feature
Use the SET PSE to enable or disable the password feature. The form of
the command is:
>>> SET PSE #

In place of #, enter a 1 to enable the feature. Enter a 0 to disable the
feature.
If you enter something other than 1 or 0, the following error message is
displayed:
?24 INV DGT

If you have not yet used the SET PSWD command to choose a password,
the following error message is displayed:
?33 NO PSWD DEF

3.4.3 Placing the Workstation in Privileged Mode
If privileged mode is selected, it is necessary to type the password at the
LOGIN command to enable console commands.
>>> LOGIN

If the password feature is not enabled, the console displays the following
error message:
?32 PSWD NOTEN

Utilities

If the password feature is enabled, the prompt appears for the console
password. The password typed in is not displayed on the screen. If the
correct password is entered, the workstation is then in privileged mode
with access to all commands.
If an incorrect password is entered, the following message is displayed:
?23 ILL CMD

3.4.4 Learning the Status of the Password Feature
To check on the status of the password feature, use the following
command:
>>> SHOW PSE

If a 1 is displayed, the feature is enabled. If a 0 is displayed, the feature
is disabled.

3.4.5 Exiting Privileged Mode
The following console commands, when executed while the console is in
the privileged mode, cause an exit from privileged mode before any other
operations begin:
•

BOOT (with any supplied parameters)

•

CONTINUE

•

HALT

•

START

Once privileged mode is exited, you must use the LOGIN command and
correctly enter the console password to regain the privileged mode.

3.5 Utility Differences for the Model 76
The following utilities are different from those used on the VS3100 Model
30, 38, 40, and 48:
•

T 55 has been replaced with show ESTAT.

•

T 70 has been replaced with T 76.

4
VAXstation 3100 (Model 76) System

4.1 System Contents
The VAXstation 3100 Model 76 (VS43A-xx) system consists of the system
box, monitor, mouse or tablet, and keyboard. The label on the back of the
system box indicates that you are working on the VS43A-xx.
The system box contains several field replaceable units (FRUs): the
system module, up to eight memory DSIMMs, a graphics module, a power
supply, and up to three internal mass storage devices (RX23 disk drive
with either one or two RZ22, RZ23, RZ23L, or RZ24 disk drives; or either
one, two, or three RZ22, RZ23, RZ23L, or RZ24 disk drives).
There are five expansion boxes available that contain additional mass
storage devices. They are:
•

TK50Z-GA storage expansion box

•

RZ55 storage expansion box

•

SZ12 storage expansion box

•

RRD40 storage expansion box

•

TLZ04 storage expansion box

34 VAXstation 3100 (Model 76) System

The keyboard is an LK201 keyboard. There are eleven monitors available.
The eleven monitors are:
•

VR160 color monitor

•

VR290 color monitor

•

VR297 color monitor

•

VR299 color monitor

•

VR320 color monitor

•

VRT16 color monitor

•

VRT19 color monitor

•

VR150 monochrome monitor

•

VR260 monochrome monitor

•

VR262 monochrome monitor

•

VR319 monochrome monitor

Figure 4–1 shows the VAXstation 3100 Model 76 system box.

VAXstation 3100 (Model 76) System 35

ThinWire
Ethernet
Port
External
Ethernet
Keyboard
SCSI
Switch
Port
Port

Standard Ethernet Halt
Ethernet Select
Button
Port
Indicators

Mouse/
Tablet
Port

Video
Port

Comm
Port

Switched Power
AC Outlet Switch

Printer
LEDs
S3
Port

VAXstation 3100 M76

MA-1317-90.DG

Figure 4–1

VAXstation 3100 Model 76 System Box

Figure 4–1 shows the front and rear of the VAXstation 3100 Model 76
system box. The monitor is connected to the 15-pin video port. A printer
can be connected to the printer port. A terminal or another printer can be
connected to the communication port. Connection to the Ethernet is done
through either the ThinWire Ethernet port or the standard Ethernet port
depending on which type of Ethernet network is available.

36 VAXstation 3100 (Model 76) System

The position of the Ethernet switch determines which of the Ethernet
ports provides IEEE 802.3 network communications. An LED is lit next
to the enabled port. The keyboard may only be connected to the keyboard
port on the back of the system box. The mouse may only be connected to
the mouse port on the back of the system box. The external SCSI port is
for connecting external mass storage devices to the system. The monitor
or an external mass storage device can be plugged into the switched ac
outlet.
The S3 switch next to the LEDs on the back of the system module controls
the console port. When the S3 switch is in the down position, it enables
the monitor connected to the monitor port to be the console. When the S3
switch is in the up position, it enables a terminal connected to the printer
port to be the console.

4.2 FRU Removal and Replacement
This section describes the removal and replacement procedures for the
FRUs in the VAXstation 3100 Model 76 system.
CAUTION
Do not remove or unplug the keyboard, mouse, printer, or
terminator without turning the power OFF. If the system is up
and running, use the proper shutdown procedure prior to halting
the system.
Figure 4–2 shows the location of the major FRUs. To use this section, find
the name of the FRU that needs replacing in Table 4–1, then go to the
section listed beside the FRU. Follow the steps in the section to remove
the FRU and reverse the procedure to replace the FRU. Always test the
replaced device for proper operation.
CAUTION
Wear an antistatic wriststrap and use an antistatic mat when
replacing FRUs.

VAXstation 3100 (Model 76) System 37

Table 4–1 FRU Section Listings
FRU

Section

System box cover

4.2.1

RZ22, RZ23, RZ23L, or RZ24 disk drive

4.2.2

RX23 disk drive

4.2.3

SCSI/FDI adapter

4.2.4

Drive plate

4.2.5

8-plane graphics coprocessor or scanprocessor option

4.2.6

Memory SIMMs

4.2.7

Internal SCSI bus data cable

4.2.9

System module

4.2.8

Power supply

4.2.10

Keyboard

4.2.11

Mouse

4.2.12

Printer

4.2.13

The FRUs for the monitors are not covered in this guide. This information
is contained in the various pocket service guides listed in Table 4–2.

38 VAXstation 3100 (Model 76) System

Table 4–2 Monitors
Monitor

Document Title

Order Number

VR150

VR150 Pocket Service Guide

EK-VR150-PS

VR160

VR160 Pocket Service Guide

EK-VR160-PS

VR260

VR260 Pocket Service Guide

EK-VR260-PS

VR262

VR262 Pocket Service Guide

EK-VR262-PS

VR290

VR290 Service Guide

EK-VR290-SV

VR297

VR297 Service Guide

EK-VR297-SG

VR299

VR299 Service Guide

EK-VR299-SG

VR319

VR319 Service Guide

EK-VR319-SV

VR320

VR320 Service Guide

EK-VR320-SV

VRT16

VRT16 Service Guide

ER-VRT16-SM

VRT19

VRT19 Service Guide

ER-VRT19-SM

Figure 4–2 shows the FRU locations.

VAXstation 3100 (Model 76) System 39

SCSI/FDI
Module
RZ22, RZ23, RZ23L
or RZ24 Hard Disks

Drive Plate

RX23 Disk Drive
Power Supply

Graphics Coprocessor
Module
Memory Modules

System Module
LJ-00688-TI0

Figure 4–2

FRU Locations

4.2.1 System Box Cover Removal
To remove the system box cover:
1. Shut down the system software.
2. Turn the system power switch OFF.

40 VAXstation 3100 (Model 76) System

3. Unscrew the two captive cover screws as shown in Figure 4–3.
4. Slide the cover forward approximately 2 inches and lift up and off the
system box.

Captive
Cover Screws
MA-1319-90.DG

Figure 4–3

Cover Screw Locations

VAXstation 3100 (Model 76) System 41

4.2.2 RZ22, RZ23, RZ23L, or RZ24 Disk Drive Removal
To remove an RZ22, RZ23, RZ23L, or RZ24 disk drive:
1. Remove the system box cover (refer to Section 4.2.1).
2. Determine your configuration by referring to Figure 4–4 and
Figure 4–5.
System Back

Position 2
RZ-Series Hard Disk

Position 3
RZ-Series Hard Disk
Position 1
RZ-Series Hard Disk

1
System Front
MLO-005465
MA-1347-90.DG

Figure 4–4

Configuration 1

42 VAXstation 3100 (Model 76) System

System Back

SCSI/FDI
Module

Position 2
RZ-Series Hard Disk

Position 1
RZ-Series Hard Disk

2
1
3

Position 3
Diskette Drive

System Front
LJ-00689-TI0

Figure 4–5

Configuration 2

3. Locate the drive plate lever under the disk drive that is being
removed. Refer to Figure 4–6 for an RZ22, RZ23, or RZ23L and
Figure 4–7 for an RZ24.
NOTE
If drive 1 is being removed, release drive 2 first for easier
access.

VAXstation 3100 (Model 76) System 43

4. Simultaneously press down on the drive plate lever and slide the drive
toward the lever until you can lift the drive from the plate. Refer to
Figure 4–6 for a disk drive in position 1 and Figure 4–7 for a disk
drive in position 2.

RZ24 Hard Disk
Mount

Press Lever
Down

Slide Drive Over
and Remove

Drive
Plate
Lever
MA-1335-90.DG

Figure 4–6

Removing a Disk Drive from Position 1

44 VAXstation 3100 (Model 76) System

RZ23 Hard Disk
Mount

Press Lever
Down

Drive
Plate
Lever

Slide Drive Over
and Remove

MA-1320-90.DG

Figure 4–7

Removing a Disk Drive from Position 2

VAXstation 3100 (Model 76) System 45

5. Disconnect the disk power cable (P/N 17–02220–01) and the SCSI
signal cable (P/N 17–02945–01) from the back of the disk that is being
removed (Figure 4–8).

Disk
Power Cable

SCSI Signal Cable

MA-1336-90.DG

Figure 4–8
Cables

Removing an RZ22/RZ23/RZ23L Disk Power and SCSI

6. Turn the drive mounting panel over and remove the four screws from
the drive (refer to either Figure 4–10 or Figure 4–11). Support the
drive with one hand when removing the last screw.
CAUTION
When reinstalling the stiffener on the RZ23/RZ23L/RZ24,
ensure that the raised edges are away from the drive PCB.

46 VAXstation 3100 (Model 76) System

7. Disconnect the drive interconnect cable and remove the two screws
with a 1/8-inch Allen wrench (refer to Figure 4–9).

TTB_X1236_88
MA-X1046-88

Figure 4–9

Removing Drive Module/Frame

8. Turn the drive over and locate the SCSI ID jumper settings E1, E2,
E3, and E4 as shown in either Figure 4–10 for the RZ22, RZ23, and
RZ23L, or Figure 4–11 for the RZ24.

VAXstation 3100 (Model 76) System 47

Record the positions of the jumpers on the drive so that you can set
the jumpers on the new drive to the same positions.
NOTE
If for some reason the SCSI ID jumpers have been tampered
with before the drive has been replaced, refer to Table 4–3 for
the RZ22, RZ23, RZ23L, and RZ24 switch settings.
Table 4–3 RZ22, RZ23, RZ23L, and RZ24 Jumpers
SCSI
ID1

E52

E62

Out

1 For RZ22, RZ23, and RZ23L.
2 E5 or E6 are present on RZ22 and RZ23 drive/modules with revision levels BO2 or higher.

For manufacturing use only.

48 VAXstation 3100 (Model 76) System

SCSI ID
Jumpers

Connector to
HDA Module

Terminator
Packs

50-Pin SCSI
Signal
Connector

E1
E2
E3

J4
E6

Signal
Port

For
Manufacturing
Only

Parity
Jumper

Power
Connector
MA-1321-90.DG

Figure 4–10

Setting the SCSI ID on the RZ22, RZ23, and RZ23L

VAXstation 3100 (Model 76) System 49

SCSI ID
Jumpers

Raised
Edges

Terminator
Packs

50-Pin SCSI
Signal
Connector

E2
E1 E3

Connector to
HDA Module

RZ Drive
Stiffener

Power
Connector
LJ-00690-TI0

Figure 4–11

Setting the SCSI ID on the RZ24

9. Reverse the removal procedure to install the new drive.
CAUTION
When replacing the four drive screws and RZ2x drive
stiffeners during the installation procedure, ensure that the
stiffener’s raised edges are away from the drive.

50 VAXstation 3100 (Model 76) System

4.2.3 RX23 Disk Drive Removal
To remove an RX23 disk drive:
1. Remove the system box cover (refer to Section 4.2.1).
2. Free the two mounting screws (refer to Figure 4–12).

RX23 Disk
Drive

Mounting
Screw

MA-1344-90.DG

Figure 4–12

Removing an RX23 Disk Drive

VAXstation 3100 (Model 76) System 51

3. Disconnect the disk power cable (P/N 17–02220–01) and the SCSI
signal cable (P/N 17–02221–01) from the back of the RX23 drive (refer
to Figure 4–13).

Disk
Switch

SCSI Signal Cable

Disk
Power Cable
MA-1345-90.DG

Figure 4–13

Removing an RX23 Disk Drive Power and SCSI Cables

4. Record the switch setting on the side of the RX23 and set the switch
on the new drive to the same position. This should be position 0.
NOTE
The RX23 drive plate lever may have shipping material under
it. If it does, remove the shipping material and discard it
before performing the next step.

52 VAXstation 3100 (Model 76) System

5. Reverse the removal procedure to install the new RX23 drive.
CAUTION
To prevent possible damage to the RX23 SCSI bus data cable
during the installation procedure, do not place the cable across
the SCSI/FDI module connector tabs.

4.2.4 SCSI/FDI Adapter Removal
To remove the SCSI/FDI adapter:
1. Remove the system box cover (refer to Section 4.2.1).
2. Locate the SCSI ID switches 1, 2, and 3 as shown in Figure 4–14.
Record the SCSI ID switch positions so that you can set the ID
switches on the SCSI/FDI replacement board to the same positions.
Usually, the switches are set to 5, as shown in Figure 4–14.
NOTE
If for some reason the SCSI ID jumpers have been tampered
with before the board has been replaced, refer to Table 4–4 for
the SCSI/FDI adapter switch settings.
Table 4–4 SCSI/FDI Adapter Switch Settings
SCSI ID

Down

VAXstation 3100 (Model 76) System 53

Switches Positions:
SCSI ID 5
Up (Off)
Down (On)
1

2 3

MA-1324-90.DG

Figure 4–14

SCSI ID Switch Location

3. Remove the two SCSI signal cables by spreading the tabs and pulling
the connectors out as shown in Figure 4–15.
4. Remove the power cable by pulling the connector out.
5. Remove the six Phillips-head screws on the SCSI/FDI adapter board.
6. Reverse this removal procedure to install the new SCSI/FDI adapter.

54 VAXstation 3100 (Model 76) System

SCSI
Signal
Cable

Disk
Power
Cable
SCSI/FDI
Module

S t andof f
MA-1323-90.DG

Figure 4–15

SCSI/FDI Module Location

VAXstation 3100 (Model 76) System 55

4.2.5 Drive Plate Removal
You do not have to remove any devices mounted on the drive plate to
remove the drive plate from the system box.
To remove the drive plate:
1. Remove the system box cover (refer to Section 4.2.1).
2. If the drive plate has devices mounted on it, complete all the following
steps. If the drive plate has no devices mounted on it, proceed to step
6.
3. Disconnect the disk power cable (P/N 17–02220–01) from the power
supply (refer to Figure 4–16).
4. Remove the SCSI cable from the system board by spreading the tabs
and pulling straight up.

56 VAXstation 3100 (Model 76) System

SCSI Signal Cable
on System Module

Disk
Power Cable

Captive
Screws (2)
Disk Power
Cable
Captive
Screws (3)

Drive Plate

Slide Mount Screws (3)
Slide Mount Openings
MA-1325-90.DG

Figure 4–16

Removing the Drive Plate

VAXstation 3100 (Model 76) System 57

5. Disconnect the SCSI terminator or the external SCSI cable from
the SCSI port on the back panel. If your system has a terminator
installed, you must remove the terminator access door before you can
remove the terminator. The access door can be released by applying
upward pressure on the bottom until the door hinges upward (refer to
Figure 4–17). At this point the whole door can be removed. Remove
the terminator (refer to Figure 4–18).

SCSI Terminator
Access Door
SCSI Terminator

SCSI Terminator
Access Door

MA-1353-90.DG

Figure 4–17

External SCSI Access Panel

58 VAXstation 3100 (Model 76) System

SCSI Terminator

MA-1354-90.DG

Figure 4–18

SCSI Terminator

6. Free the five captive screws and loosen the three slide mount screws
on the drive plate as shown in Figure 4–16. Do not remove the screws
from their mountings.
7. Slide the drive plate (with the drives) forward approximately 1/2-inch
and then lift it up and off the system box. Feed through the disk
power cable as shown in Figure 4–19. Set the plate aside.
8. To install the drive plate, feed through the disk power cable as
shown in Figure 4–19 and then continue by reversing this removal
procedure.

VAXstation 3100 (Model 76) System 59

SCSI Signal Cable

Captive
Screw

Disk
Power Cable
MA-1384-90.DG

Figure 4–19

Replacing the Drive Plate

60 VAXstation 3100 (Model 76) System

4.2.6 Graphics Coprocessor Module Removal
To remove the graphics coprocessor module:
1. Remove the system box cover (refer to Section 4.2.1).
2. Remove the drive plate (refer to Section 4.2.5).
3. Remove the graphics coprocessor module from the four standoffs (refer
to Figure 4–20).
CAUTION
If you have an SPX color graphics accelerator, there is an IC
(on the SPX graphics module) whose pins are susceptible to
bending near the rear corner furthest from the power supply.
Be extremely careful in handling this module so as not to
cause permanent damage.

Standoff
Standoffs

Graphics Coprocessor
Module
Connectors Underneath
Module

Standoffs
MA-1326-90.DG

Figure 4–20

Removing the Graphics Coprocessor Module

VAXstation 3100 (Model 76) System 61

4. Grasp the module near the two connectors under the module and
lift the graphics coprocessor module off the system module. Refer to
Figure 4–21 for the location of the connector.
5. Reverse this removal procedure to install a new graphics module.
System Side View
Graphics Coprocessor
Module

Module
Connectors

Power Supply

Standoff
System Module

Module Connectors

Standoff
MA-1334-90.DG

Figure 4–21
View

Removing the Graphics Coprocessor Module - Sectional

4.2.6.1 Graphics Coprocessor Module 60Hz/66Hz Selection
There is a two position dip switch located on the Graphics Coprocessor
module (non-component side) that is used to switch between 60Hz and
66Hz monitor support.
•

Switch #1 is inactive.

•

Switch #2 should be in the ON position for 66 Hz monitors.

The dip switch can be accessed without removing the drive plate. To set
the dip switch:
1. Remove the storage drive located in drive position 1 (see Figure 4–5).
NOTE
Once the storage drive has been removed you can gain access
to the dip switch (white) through a opening in the drive plate
located near the power supply.

62 VAXstation 3100 (Model 76) System

2. Select the appropriate dip switch setting.

4.2.7 Memory SIMM Removal
To remove a memory module:
1. Remove the system box cover (refer to Section 4.2.1).
2. Remove the drive plate (refer to Section 4.2.5).
CAUTION 1
Memory components are easily damaged with static electricity.
An antistatic wriststrap should always be worn when
installing or removing memory components.
CAUTION 2
The memory SIMMs are keyed and should be installed in only
one direction. Excessive force applied to the SIMMs when
they are not properly aligned with the connector can cause
permanent damage to either the SIMM or connector.
NOTE
Memory SIMMs must always be removed starting from the
rear of the system. For example, if you are going to replace
the SIMM at the front of the system board, you must remove
the other three starting at the rear and working toward the
front. Memory modules are numbered on the outer edges of
the memory connectors located on the system board.
3. To remove a SIMM, release the two metal retainers located on each
SIMM memory connector (refer to Figure 4–22). Tilt the module
approximately 55 degrees to the rear of the unit and lift out (refer to
Figure 4–22).
CAUTION
Failure to release the two memory retainers will permanently
damage the memory connector located on the system board.
4. Repeat the previous step for each memory SIMM that must be
removed.
5. Reverse this removal procedure to install a new SIMM, noting the
following. Be sure to insert the new SIMM at the angle it was
removed, then tilt upward until the retainers lock into place.

VAXstation 3100 (Model 76) System 63

SIMM
Module
Notch

SIMM
Module

SIMM
Slot

Key

3
SIMM
Memory
Connector
2

Retainer
MA-1333-90.DG

Figure 4–22

Removing Memory Modules

64 VAXstation 3100 (Model 76) System

4.2.8 System Module Removal
To remove a system module:
1. Disconnect all cables from the back of the system box.
2. Remove the system box cover (refer to Section 4.2.1).
3. Remove the drive plate (refer to Section 4.2.5).
4. Remove the graphics coprocessor module (if installed) from the system
(refer to Section 4.2.6).
5. Disconnect the system power cable from the system module by
releasing the lock on the connector (refer to Figure 4–23).
Phillips-head Screws (6)

System Power Cable

Phillips-head Screws (3)
Locating Post

Phillips-head Screws (3)
Locating Post
MA-1382-90.DG

Figure 4–23

System Module

6. Remove the twelve Phillips-head screws from the system module as
shown in Figure 4–23.

VAXstation 3100 (Model 76) System 65

7. Remove the system module by carefully popping up the two front
corners off the two locating posts as shown in Figure 4–24.
CAUTION
ROM chips are static sensitive devices. An antistatic
wriststrap should be worn while removing or replacing a
ROM chip.
Phillips-head Screws (6)

System Power Cable
Phillips-head Screws (3)

Locating Post

Phillips-head Screws (3)
Locating Post
MA-1328-90.DG

Figure 4–24

Removing the System Module

8. Remove the memory SIMMs (refer to Section 4.2.7).
9. Use either a ROM puller or slide a small screwdriver under each end
of the Ethernet ID ROM, and carefully lift the ends until you can
remove the ROM from the system module. Figure 4–25 shows the
Ethernet ID ROM.

66 VAXstation 3100 (Model 76) System

Ethernet
ID ROM
Key

ROM
Socket

Ethernet
ID ROM
MA-1381-90.DG

Figure 4–25

Removing the Ethernet ID ROM

CAUTION
Do not bend the pins on the ROM. You must add this ROM to
the replacement system module. The Ethernet ID ROM key
must face the back of the system. If you put the Ethernet ID
ROM in backwards, the system will not function properly. See
Figure 4–25 for the proper orientation of the Ethernet ID ROM
key.
To replace a system module:
1. Remove the Ethernet ID ROM from the new system module and
reinstall it on the old system module.
2. Take the Ethernet ID ROM you removed from the old system module
and insert it in the new system module. Use Figure 4–25 as a
reference. The key faces the rear of the module.

VAXstation 3100 (Model 76) System 67

3. Place the new system module in the system box making sure the
connectors slide through the openings in the rear of the system box as
shown in Figure 4–26.
Phillips-head Screws (6)

System Power Cable
Phillips-head Screws (3)

Locating Post

Phillips-head Screws (3)
Locating Post
MA-1383-90.DG

Figure 4–26

Installing the System Module

4. Push the module toward the back of the box until the front set of
holes on either side of the module fit on the two locating posts on
the bottom of the box. You must apply some pressure because of the
elasticity of the connector shieldings surrounding the connectors at
the back of the module. Snap the module on the locating posts.
5. Check that the screw holes are aligned. Install and tighten the twelve
Phillips-head screws.
6. Plug in the power cable on the system module.
7. Replace the memory SIMM(s).
8. Reinstall the graphics coprocessor by aligning it with the four
standoffs and applying downward pressure so as to lock the locating
pins.

68 VAXstation 3100 (Model 76) System

9. Reinstall the drive plate and install all the cables in the system box.
10. Reinstall the system box cover.
11. Reinstall all the cables and terminators to the rear of the box.

4.2.9 Internal SCSI Bus Data Cable Removal
To remove the internal SCSI bus data cable, remove the system box cover
(refer to Section 4.2.1 and Figure 4–27) and then:

! Disconnect the SCSI bus data cable from the system module.
" If you have an RX23 disk drive, disconnect the SCSI bus data cable
from its drive module.

# Disconnect the SCSI bus data cable from all the hard drives. Note
that if you remove the drives from the drive plate, it is easier to
disconnect the cable.

$ Remove the end of the SCSI bus data cable from the Velcro at the

front of the drive plate by lifting the cable straight up. Then remove
the terminator from the cable.

% Remove the SCSI/FDI module.
& Cut the tie wrap that holds the cable and the ferrite core on the drive.
' Remove the two screws that hold the cable to the drive plate at the
external SCSI port.

( Lift the cable out of the hole in the drive plate and away from the
external SCSI port.

CAUTION
To prevent possible damage to the RX23 SCSI bus data cable do
not place cable across the SCSI/FDI module connector tabs.
Reverse this removal procedure to reinstall the internal SCSI bus data
cable. Ensure that you replace the tie wrap and the internal terminator
(refer to Figure 4–27).

VAXstation 3100 (Model 76) System 69

7
4

2
5

MA-1385-90.DG

Figure 4–27

Removing the Internal SCSI Bus Data Cable

4.2.10 Power Supply Removal
To remove a power supply:
1. Remove the system box cover (refer to Section 4.2.1).
2. Remove the drive plate (refer to Section 4.2.5).
3. Disconnect the power cable from the system module (refer to
Figure 4–26).

70 VAXstation 3100 (Model 76) System

4. Unscrew the two flat-head captive screws and the two Torx screws on
the side as shown in Figure 4–28.

Captive Screw

Power Supply
Captive Screw
Torx Screws

MA-1331-90.DG

Figure 4–28

Power Supply Screw Locations

5. Lift the power supply out of the system box.
6. Reverse this removal procedure to install a new power supply.

4.2.11 Keyboard Removal
CAUTION
Do not remove or unplug the keyboard, mouse, printer, or
terminator without turning the power OFF. If the system is up
and running, use the proper shutdown procedure prior to halting
the system.

VAXstation 3100 (Model 76) System 71

Unplug the keyboard cable from the rear of the system box (refer to
Figure 4–29).
NOTE 1
The keyboard is a single FRU. Do not try to remove the keycaps
or disassemble the keyboard.
NOTE 2
The keyboard must always be plugged directly into the back of
the unit.

Communication
Printer
Mouse
Keyboard

MA-1332-90.DG

Figure 4–29

Keyboard, Mouse, and Printer Removal

72 VAXstation 3100 (Model 76) System

4.2.12 Mouse Removal
Disconnect the mouse from the back of the system box (refer to
Figure 4–29).
CAUTION
Do not remove or unplug the keyboard, mouse, printer, or
terminator without turning the power OFF. If the system is up
and running, use the proper shutdown procedure prior to halting
the system.
NOTE 1
The mouse and the tablet are single FRUs. Do not try to
disassemble them.
NOTE 2
The mouse must always be plugged directly into the back of the
unit.

4.2.13 Printer Removal
CAUTION
Do not remove or unplug the keyboard, mouse, printer, or
terminator without turning the power OFF. If the system is up
and running, use the proper shutdown procedure prior to halting
the system.
To remove a printer:
1. Switch the printer’s power switch OFF.
2. Disconnect the printer cable from the back of the system box (refer to
Figure 4–29) or from the back of the printer.
3. Refer to the specific printer’s pocket service guide for troubleshooting
and removal and replacement procedures for the printer.

A
Recommended Spares List
Part Number

Description

Quantity

VAXstation 3100 Model 76
.
54-19847-01

VAXstation Model 76 system module (VS43A-xx)

54-19288-01

SCSI/FDI adapter module

54-17282-01

8-plane graphics coprocessor module (VS40X-PA)

RZ22-E

52 Mbyte SCSI disk drive with logic module

29-27240-01

104 Mbyte SCSI disk drive with logic module (RZ23E)

RZ23L-E

121 Mbyte SCSI disk drive with logic module (RZ23LE)

RZ24-E

209 Mbyte SCSI disk drive with logic module

29-27240-01

RZ22/RZ23 module/frame assembly

29-28144-01

Module/frame assembly (RZ24)

54-19623-01

8-plane SPX graphics coprocessor module (WS01X-GA
/GB)

MS44-AA

4 Mbyte DSIMM memory

H7821-00

Power supply

RX23-AA

RX23 with SCSI adapter assembly (RX23-AA)

17-02220-01

Internal power cable

17-02221-01

Internal RX23 data cable

17-02221-02

RX23 data cable (connects RX23 to SCSI adapter
module)

17-02945-01

Internal SCSI bus data cable

74 Recommended Spares List

Part Number

Description

Quantity

12-33816-01

Internal SCSI terminator

VAXstation 3100 Model 76 (loopbacks, terminators, and external cables)
17-01992-01

BC23J-03 color monitor cable (short)

17-01993-01

BC23K monochrome monitor cable (short)

17-00606-10

System power cord (USA)

17-00442-26

System-to-monitor power cord

17-02008-01

68 to 50-pin external SCSI port cable

17-01351-01

50 to 50-pin SCSI cable

17-01351-04

50-pin SCSI cable (18 inches)

12-22196-01

Standard Ethernet loopback

12-25869-01

ThinWire Ethernet T-connector

12-26318-01

ThinWire Ethernet cable 50-ohm terminator

12-25083-01

MMJ loopback connector (H3103)

12-29635-01

68-pin external SCSI port terminator

12-30552-01

50-pin SCSI terminator

17-00811-03

BC16E-25 DECconnect office cable (25 feet)

17-00811-04

BC16E-50 DECconnect office cable (50 feet)

BA42 Expansion Box FRUs
RX23-AA

RX23 disk drive

RX33-A

RX33 disk drive

TZ30-A

TZ30 tape drive

54-19325-02

SCSI ID switch module

17-00606-10

System power cord (USA)

17-02443-01

68—50 external SCSI cable

17-02446-01

50—50 external SCSI cable

17-02445-01

SCSI ID switch cable

17-02447-01

Internal power supply cable w/resistor

Recommended Spares List 75

Part Number

Description

Quantity

17-02444-01

Internal data cable

TZK10-ZZ

—

–

H7821-00

Power supply

17-00606-10

Power cord (USA)

29-28145-01

RZ24 HDA

70-26717-01

RZ55 disk drive

29-27347-01

RZ55 PCB

29-27890-01

RZ56 HDA

29-27889-01

RZ56 PCB

29-28159-01

RZ57 HDA

29-28158-01

RZ57 PCB

54-19288-01

SCSI/FDI adapter module

74-39202-01

Full height drive mounting bracket

74-41483-01

Half height drive mounting bracket

RX23-EA

RX23 3-1/2 inch floppy disk drive

RX33-A

RX33 5-1/4 inch floppy disk drive

RX23L-E

RX23L disk drive

TZ30-AX

TZ30 1/2 inch cartridge tape drive

TZK10-AA

TZK10 1/4 inch cassette (QIC) tape drive

RRD40 Compact Disk Expansion Box FRUs
RRD40-DA

RRD40 compact disk expansion box (with SCSI
interface)

Miscellaneous Parts
LK201-XX

Keyboard (USA keycaps)

17-01480-01

VSXXX-AA mouse

29-25997-00

Tablet assembly

70-27986-01

Drive plate assembly

76 Recommended Spares List

Part Number

Description

Quantity

74-41401-01

Metal standoff

74-41401-02

Metal standoff

74-41401-03

Metal standoff

74-41401-04

Metal standoff

12-31489-01

Thermal pad

30-23507-03

RRD40 test disk

29-27338-01

RRD40 empty caddy

30-20515-01

TZ30 blank media

30-25145-05

RX23 blank media

29-25995-00

Stylus

29-25996-00

Puck

29-25992-00

Mouse ball

29-25993-00

Mouse door

90-07032-00

Tie wrap

90-07031-00

Tie wrap

A2-M1329-10

Color maintenance kit (two 75-ohm terminators
29-26899-00)

B
Self-Tests

B.1 Console’s Configuration Display Utility (T 50)
The results of the self-test are available through the console’s
configuration display utility (T 50). The general format is as pictured
below.
>>> T 50

KA43-A V1.0
ID xx-xx-xx-xx-xx-xx
MONO
0000.0xxx
(test F)
CLK
0000.00xx
(test E)
NVR
0000.00xx
(test D)
DZ
0000.xxxx
(test C)
0000xxxx 0000xxxx 0000xxxx 0000xxxx kkkkkkkk mmmmmmmm
MEM
000y.00xx
(test B)
ssssssss 0000mmmm
FP
0000.000x
(test 9)
IT
0000.000x
(test 8)
SCSI A
wxy0.wxyz
(test 7)
ddmmsstt ddmmsstt ddmmsstt ddmmsstt ddmmsstt ddmmsstt ddmmsstt ddmmsstt
SCSI B
wxy0.wxyz
(test 6)
ddmmsstt ddmmsstt ddmmsstt ddmmsstt ddmmsstt ddmmsstt ddmmsstt ddmmsstt
SYS
0000.0xxx
(test 5)
8PLN
0000.0001 V1.0
NI
xxxx.yyyy
(test 1)

B.2 NI (test 1)
The NI status has one longword of status and error information,
formatted as follows:
xxxx.yzzz
where y is the subtest number, zzz is the subtest status, and xxxx has
variable meaning depending upon the value of y.

78 Self-Tests

Should the initialization code encounter an error, the test number will be
zero.
#^x0002 ; could not find a good page of memory for init block
#^x0004 ; could not find 3 contiguous pages for receive buffer
#^x0006 ; could not find 3 contiguous pages for transmit buffer

B.2.1 TEST 1:
#^x1002 ; failed init
#^x1004 ; RX not enabled
#^x1006 ; TX enabled
#^x1008 ; init failed
#^x100A ; RX enabled
#^x100C ; TX not enabled

B.2.2 TEST 2:
high word : pkt data length (1 byte), index into pattern table (1 byte)
#^x2002 ; init failed
#^x2004 ; failed loop

B.2.3 TEST 3:
high word : pkt data length (1 byte), index into pattern table (1 byte)
#^x3002 ; init failed
#^x3004 ; failed loopback
#^x3006 ; no CRC match
#^x3008 ; init failed
#^x300A ; failed TX
#^x300C ; failed RX
#^x300E ; init failed
#^x3010 ; failed TX
#^x3012 ; OWN not toggled
#^x3014 ; no RX error
#^x3016 ; no STP
#^x3018 ; no ENP
#^x301A ; no CRC error
#^x301C ; no FRAM error
#^x301E ; no RINT

Self-Tests 79

B.2.4 TEST 4:
high word : multicast filter bit number being tested
#^x4002 ; init failed
#^x4004 ; TX failed
#^x4006 ; packet received
#^x4008 ; bad filter value
#^x400A ; init failed
#^x400C ; failed loopback
#^x400E ; init failed
#^x4010 ; failed loopback

B.2.5 TEST 5:
#^x5002 ; init failed
#^x5004 ; OWN not toggled
#^x5006 ; no RTRY error
#^x5008 ; TX turned off
#^x500A ; init failed
#^x500C ; TX failed
#^x500E ; no rcv MISS

B.2.6 TEST 6:
#^x6002 ; init failed
#^x6004 ; loopback failed
#^x6006 ; bad CSR0
#^x6008 ; no NI interrupt
#^x600A ; init failed
#^x600C ; loopback failed
#^x600E ; wrong # of int’s.
#^x6010 ; NI int. bits set

B.2.7 TEST 7:
#^x6002 ; init failed
#^x6004 ; loopback failed
#^x6006 ; bad CSR0
#^x6008 ; no NI interrupt
#^x600A ; init failed
#^x600C ; loopback failed
#^x600E ; wrong # of int’s.
#^x6010 ; NI int. bits set

80 Self-Tests

B.3 COLOR (test 4)
8-plane video option board:
Error code format :
xxx.yyyz Where z = 1 for normal
2 for fatal error
3 for soft error
yyy = test that failed (from the error codes )
xxx = error or status number within the
particular test
error$_initialization = x0001
error$_chip_select = x0002
error$_long_memory = x0003
error$_memory
= x0004
error$_id_data
= x0005
error$_scrolling = x0006
error$_fcc_initialization = x0007
error$_fcc_ram_counters = x0008
error$_fcc_ram
= x0009
error$_Display_List_Commands = x0010
error$_short_display_list = x0011
error$_packing
= x0012
error$_compression_b = x0013
error$_adder_interrupt = x0014
error$_fcc_interrupt = x0015
error$_vdac
= x0016
error$_cursor_bitmap = x0017
error$_sync_readback = x0018
error$_left_edge_detect = x0019
error$_right_edge_detect = x0020
error$_video_readback = x0021
error$_cursor_readback = x0022

Self-Tests 81

8-plane video option board:
Error code format :
xxx.yyyz Where z = 1 for normal
2 for fatal error
3 for soft error
yyy = test that failed (from the error codes )
xxx = error or status number within the
particular test
initialization
x01
chip_select
x02
memory_data_path
x3A
short_memory
x04
id_data
x05
scrolling
x06
fcc_initialization
x07
fcc_ram_counters
x08
fcc_ram
x09
short_display_list
x11
packing
x12
compression_b
x13
adder_interrupt
x14
fcc_interrupt
x15
vdac
x16
cursor_bitmap
x17
sync_readback
x18
video_readback
x21
left_edge_detect
x19
right_edge_detect
x20
cursor_readback
x22

82 Self-Tests

B.4 SYS (test 5)
The system power-up self-test has one longword of status and error
information, formatted as follows:
SYS

0000.0XXX

where XXX is one of the status or error codes listed in the following table.
Error
Code

Status

Description

Status:

Success

Error:

System ROM failed checksum

Error:

Ethernet ROM failed checksum

Error:

No interrupts pending

Error:

All of the expected interrupts failed to happen

Error:

One of the interrupts was not enabled but happened anyway

Error:

Improper priority

Error:

Default interrupt service routine was called. An interrupt
that was not enabled occurred

100

Error:

No keyboard found in the system configuration

Self-Tests 83

B.5 SCSI-B (test 6)
The SCSI-B power-up self-test has one longword of status information for
the controller and eight longwords of status information for the devices.
The formats of each are pictured below.
Controller Status

SCSI B SSGG.FFCC
DDMMSSTT DDMMSSTT DDMMSSTT DDMMSSTT DDMMSSTT DDMMSSTT DDMMSSTT DDMMSSTT

ID 0
Status

ID 1
Status

ID 2
Status

ID 3
Status

ID 4
Status

ID 5
Status

ID 6
Status

where the controller status fields are:
SS is a bitmask of target IDs that could be selected
GG is a bitmask of target IDs that tested OK
FF is a set of bitmask flags
CC is the controller status/error code
where each target status field is:
DD is the first byte returned in the Inquiry data phase
MM is the first byte returned in the Inquiry message_in phase
SS is the first byte returned in the Inquiry status phase
TT is the target status/error code
Another look at controller status:

ID 7
Status

84 Self-Tests

24 23
Selected

16 15

Tested OK

Flags

08 07

00
Status
Controller Status
(see below)

Binary Flags
00000001=problem on system board
00000010=problem off system board
00010000=reset required to free bus
00100000=not all selected devices OK
01000000=DMA and ’rupts untested
Binary Mask of Devices that tested successfully
00000001=ID 0
00000010=ID 1
00000100=ID 2
00001000=ID 3
00010000=ID 4
00100000=ID 5
01000000=ID 6
10000000=ID 7
Binary Mask of Devices that selected successfully
(same format as above)

Self-Tests 85

Controller
Status
Code
Status

Description

Status:

Everything is fine

Error:

Disk/tape buffer RAM addressing failure

Error:

Disk/tape buffer RAM byte mask failure

Error:

Disk/tape buffer data path failure

Error:

Error in 5380 SCSI registers during reset

Error:

Error in 5380 SCSI registers after reset

Error:

Unexpected interrupt after reset, IPL = 1Fh

Error:

No interrupt request after reset

Error:

No interrupt after reset when IPL has been lowered

Error:

Interrupt request not cleared following ISR (after reset)

Error:

Multiple interrupts following reset

Error:

Unknown interrupt following reset

Error:

Wrong interrupt following reset

Error:

Phase not ’bus free’ at start of test (even after a reset)

Error:

First attempt to read 5380 SCSI register (ini_cmd) failed

Error:

5380 SCSI register address test failed at ini_cmd

Error:

5380 SCSI register address test failed at mode

Error:

5380 SCSI register address test failed at tar_cmd

Error:

5380 SCSI register address test failed at scd_cnt (in
standard cell)

Error:

Mode<dma> found set after being cleared when ini_
cmd<bsy> clear

Error:

Mode<dma>found set after being set when ini_
cmd<bsy>clear

Error:

Mode<dma> found set after being cleared when ini_
cmd<bsy> set

Error:

Mode<dma> found clear after being set when ini_
cmd<bsy>set

Error:

Data output to bus with ini_cmd<enout> clear

86 Self-Tests

Controller
Status
Code
Status

Description

Error:

No data to bus with ini_cmd<enout>set

Error:

Parity bit (cur_stat<dbp>) does not correspond with data
on bus

Error:

With bus free, data in did not match data out

Error:

ini_cmd<sel> to cur_stat<sel> mismatch

Error:

ini_cmd<ack> to status<ack>, or ini_cmd<atn> to
status<atn> mismatch

Error:

tar_cmd<req> to cur_stat<req>, or tar_cmd<MSG> to
cur_stat<MSG>, or tar_cmd<cd> to cur_stat<cd>, or tar_
cmd<io> to cur_stat<io> mismatch with mode<targ> set

Error:

Clearing mode<targ>does not prevent tar_cmd bits from
appearing on the bus (in cur_stat)

Error:

ISR hit with IPL = 1Fh and int_msk<sc> clear

Error:

Interrupt request (int_req<sc>) set for no apparent reason

Error:

SCSI’s status<intreq> set for no apparent reason

Error:

Bus busy at start of interrupt test so we cannot test them

Error:

ISR hit following bus free with IPL = 1Fh and int_msk
<sc>clear

Error:

Interrupt request (int_req<sc>) not set following bus free

Error:

SCSI’s status<intreq> not set following bus free

Error:

Status<bsyerr> was not set even though it caused an
interrupt

Error:

Bus busy during interrupt test so we cannot test them

Error:

ISR hit following bus free with IPL = 1Fh and int_msk
<sc> set

Error:

Interrupt request (int_req<sc>) not set following bus free

Error:

SCSI’s status<intreq> not set following bus free

Error:

Status<bsyerr> not set following bus free

Error:

Bus busy during interrupt test so we cannot test them

Error:

Timeout waiting for bus free interrupt

Self-Tests 87

Controller
Status
Code
Status

Description

Error:

ISR not hit following bus free

Error:

Interrupt request (int_req<sc>) not cleared following ISR
after bus free

Error:

SCSI’s status<intreq> not set following bus free

Error:

Multiple interrupts from bus free

Error:

Unknown interrupt from bus free

Error:

Wrong interrupt from bus free

Error:

Bus busy during interrupt test so we cannot test
interrupts

Error:

Timeout waiting for parity interrupt

Error:

ISR not hit following parity

Error:

Interrupt request (int_req<sc>) not cleared following ISR
after parity

Error:

SCSI’s status<intreq> not set following parity

Error:

Multiple interrupts from parity

Error:

Unknown interrupt from parity

Error:

Wrong interrupt from parity

Error:

Phase not ’bus free’ before arbitration

Error:

ini_cmd<aip> bit failed to set

Error:

Lost arbitration (first check of ini_cmd<la>)

Error:

Higher priority device on bus

Error:

Lost arbitration (second check of ini_cmd<la>)

Error:

Not all selected targets tested OK (basically the same as
flag 2)

88 Self-Tests

Another look at device status:
There is a status longword for each possible device (eight of them) on the
bus. Each of these statuses has the following format:
31

24 23
INQ Data

16 15

INQ Message

08 07

INQ Status

00
Status
Target Status
(see below)

First byte returned in status phase
for an INQUIRY command (FFh if none)
First byte returned in message_in phase
for an INQUIRY command (FFh if none)
First byte returned in data_in phase
for an INQUIRY command (FFh if none)

The device statuses appear on the screen in increasing ID order, that is,
the device whose ID is zero is on the left and the device whose ID is seven
is rightmost. Note that ID SIX is reserved by the system architecture to
be the host ID.
Target
Status
Code

Status

Description

Status:

Status: target untested

Status:

This target is fine

Status:

This ID used for the host

Status:

Target did not respond to selection

Error:

Target did not set cur_stat<req>soon enough when
changing phase

Error:

Jitter on the phase lines when changing phase

Error:

Target set command phase twice

Error:

Target changed phase before command complete

Error:

Target failed to set cur_stat<req> when getting command

Self-Tests 89

Target
Status
Code

Status

Description

Error:

Target failed to clear cur_stat<req> when getting
command

Error:

Command phase out of sequence

Error:

Stuck in command phase

Error:

Target set data_in phase twice

Error:

Target failed to set cur_stat<req> when returning data

Error:

Target failed to clear cur_stat<req> when returning data

Error:

Target changed data_in phase before transferring any
data

Error:

Data_in phase out of sequence

Error:

Stuck in data_in phase

Error:

Target set status phase twice

Error:

Target failed to set cur_stat<req> when returning data

Error:

Target failed to clear cur_stat<req> when returning data

Error:

Target changed status phase before transferring any data

Error:

Status phase out of sequence

Error:

Stuck in status phase

Error:

Target set message_in phase twice

Error:

Target failed to set cur_stat<req> when returning data

Error:

Target failed to clear cur_stat<req> when returning data

Error:

Target changed message_in phase before transferring any
data

Error:

Message_in phase out of sequence

Error:

Stuck in message_in phase

Error:

Target set data_out phase (unexpectedly)

Error:

Target set phase to 100b (reserved phase)

Error:

Target set phase to 101b (reserved phase)

Error:

Target set message_out phase

90 Self-Tests

Target
Status
Code

Status

Description

Error:

Selected target did not set any phase before releasing bus

Error:

Target not following expected phase sequence

Error:

Parity error detected during programmed I/O transfer

Error:

Unexpected interrupt at start of DMA test

Error:

Target failed to set command phase

Error:

Unexpected interrupt at start of command phase sequence

Error:

Timeout waiting for DMA complete in command phase in
DMA test

Error:

No status<DMAEND> following command phase in DMA
test

Error:

Wrong interrupt following command in DMA test

Error:

scd_cnt not zero following command in DMA test

Error:

DMA not complete after EOP in command phase (ACK
not clear soon enough)

Error:

Status<dmaend> bit not cleared by clearing mode<dma>
at start of data_in phase in DMA test

Error:

Target failed to set data_in phase in DMA test

Error:

Timeout waiting for DMA complete in data_in phase in
DMA test

Error:

No status<dmaend> following data_in phase in DMA test

Error:

Wrong interrupt following data_in phase in DMA test

Error:

scd_cnt not zero following data_in phase in DMA test

Error:

DMA not complete after EOP in data_in phase (ACK not
clear soon enough)

Error:

Status<dmaend>not cleared by clearing mode <dma> at
start of status phase in DMA test

Error:

Target failed to set status phase in DMA test

Error:

Timeout waiting for DMA complete in status phase in
DMA test

Error:

No status<dmaend> following status phase in DMA test

Self-Tests 91

Target
Status
Code

Status

Description

Error:

Wrong interrupt following status in DMA test

Error:

scd_cnt not zero following status in DMA test

Error:

DMA not complete after EOP in status phase (ACK not
clear soon enough)

Error:

Status<dmaend> not cleared by clearing mode<dma> at
start of message_in phase in DMA test

Error:

Target failed to set message_in phase in DMA test

Error:

Timeout waiting for DMA complete in message_in phase
in DMA test

Error:

No status<dmaend> following message_in phase in DMA
test

Error:

Wrong interrupt following message_in phase in DMA test

Error:

scd_cnt not zero following message_in phase in DMA test

Error:

DMA not complete after EOP in message_in phase (ACK
not clear soon enough)

Error:

Status<dmaend> not cleared by clearing mode <dma> at
end of DMA test

Error:

Bus not free soon enough at end of DMA test

Additional debug information in disk/tape buffer.

92 Self-Tests

SCSI registers and software flags are saved in this format:
Offset

Size

Description

.byte

cur_data (5380 register)

.byte

ini_cmd (5380 register)

.byte

mode (5380 register)

.byte

tar_cmd (5380 register)

.byte

cur_stat (5380 register)

.byte

status (5380 register)

.byte

in_data (5380 register)

.word

scd_cnt (standard cell register)

.long

software’s controller status

.byte

software’s phase_seen flags
bit 7=message_in,
6=message_out,
5=reserved,
4=reserved,
3=status,
2=command,
1=data_in,
0=data_out

.long

software’s interrupt flags
bit9=unknown interrupt,
8=bus reset,
7=bus disconnect,
6=phase mismatch,
5=parity error,
4=DMA EOP,
3=reselect,
2=select,
1=multiple interrupts detected,
0=at least one interrupt detected

200D.0x00 - SCSI registers following inquiry command to ID ’x’
200D.0x40 - request_sense data_in from ID ’x’ (if any)
200D.0x80 - inquiry DMA data_in from ID ’x’ (if any)
200D.0xC0 - inquiry DMA status from ID ’x’ (if any)
200D.0xE0 - inquiry DMA message_in from ID ’x’ (if any)

Self-Tests 93

Offset

Size

Description

200D.0a00 - SCSI registers at end of test_scsi_interrupts
200D.0b00 - SCSI registers at end of test_scsi_reg_function
200D.0c00 - SCSI registers at end of test_scsi_reg_addr
200D.0d00 - SCSI registers at end of test_disk_buffer
200D.0e00 - SCSI registers at end of test_scsi_bus_free
200D.0f00 - SCSI registers at start of test

B.6 SCSI-A (test 7)
These tests, codes, and registers are the same as those shown for test 6.

B.7 IT (test 8)
The interval timer power-up self-test has one longword for status
information in the following format:
IT

0000.000X

where X is one of the status or error codes listed in the following table:
Code

Status

Definition

Status:

Success

Error:

Fatal error

94 Self-Tests

B.8 FP (test 9)
The floating point unit power-up self-test has one longword for status
information in the following format:
FP

0000.000X

where X is one of the status or error codes listed in the following table:
Code

Status

Definition

Status:

Success

Error:

Floating point error

Error:

Invalid floating point exception

B.9 MEM (test B)
The memory power-up self-test has two or three longwords for status
information in the following format:
MEM

00YY.00XX
SSSSSSSS

(if no missing memory)

MEM

00YY.00XX (if some memory is bad)
SSSSSSSS 0000MMMM

where Y is the number of megabytes that are expected to be in the system
(from the CFGTST register), and XX is one of the status or error codes
listed in the following table. The first error code for the MEM indicates
the status of all the main memory system. The second line contains
additional information on the memory system, where SSSSSSSS is the
total number of bytes of good memory found in the system. If this field is
not in an even megabyte value (that is, 00020000), then the second field,
MMMM, will be displayed to indicate the failing megabyte bank. Each bit in
the YYYY status code indicates the status for one bank of memory (bit set
means bad). In some cases, where a parity error was detected, two banks
may indicate a bad bank of memory since the test does the testing on a
nonpage aligned region at the beginning of one page and at the end of the
previous page.

Self-Tests 95

Code

Status

Definition

Status:

Success

Error:

Failure in test_address routine

Error:

Byte mask failure

Error:

Data/address test failure

Error:

No memory was found during sizing

Error:

Unexpected parity error

Error:

Memory sizing error

Error:

Actual memory size does not match CFGTST register

B.10 DZ (test C)
The serial line (DZ) power-up self-test has one longword for general
controller status information, four longwords for line status information,
and two longwords for status information of any keyboard or pointing
device on the system. The format is as follows:
Controller
Status

0000.XXXX
DZ
0000XXXX 0000XXXX 0000XXXX 0000XXXX KKKKKKKK MMMMMMMM

Line 0
Status

Line 1
Status

Line 2
Status

Line 3
Status

Keyboard
Status

Mouse
Status

where XXXX is one of the status or error codes listed in the following table,
KKKKKKKK is the keyboard’s internal self-test status code, and MMMMMMMM
is the mouse or tablet’s internal self-test status code. The keyboard and
mouse are tested only at power-up, so these values will not change when
test C is executed from the console.

96 Self-Tests

Expected values for the keyboard status code are:
00000000 if TEAMmate or no keyboard
00000001 if OK
000000FD if loopback
Expected values for the mouse status code are:
00000000 if TEAMmate or no mouse
000012A0 if OK
00000054 if loopback

Code

Status

Definition

Status:

Success

4000

Status:

This line is untested
(for VAXstar: line 3 used as console:
for TEAMmate: line 0 used as console)

Error:

Master reset failed

Error:

Failure in basic ser_csr test

Error:

Failure in ser_csr read/write test

Error:

Basic test of ser_tcr failed

Error:

Read/write test of ser_tcr failed

Error:

Transmitter ready test failed

Error:

Receiver ready test failed

100

Error:

Transmitter interrupt timeout

200

Error:

Receiver interrupt timeout

400

Error:

Either transmitter or receiver interrupted at the wrong
priority

800

Error:

Receiver interrupt occurred when the receiver was not
enabled

1000

Error:

Data comparison error

2000

Error:

Overrun error did not happen when expected

8000

Error:

Error in the modem control logic test

Self-Tests 97

B.11 NVR (test D)
The nonvolatile RAM (NVR) power-up self-test has one longword of status
information in the following format:
NVR

0000.00XX

where XX is one of the status or error codes listed in the following table:
Code

Status

Definition

Status:

Success

Status:

Battery voltage was low since last entry

Error:

NVR failed

Error:

The battery check code in the NVR did not agree with the
expected check code

B.12 CLK (test E)
The time-of-year clock (CLK) power-up self-test has one longword of status
information in the following format:
CLK

0000.00XX

where XX is one of the status or error codes listed in the following table:
Code

Status

Definition

Status:

Success

Status:

Clock has not been reset since the last time the battery
voltage was low

Error:

Internal test value to inform dispatcher to check time at the
end of the testing (should never be reported)

Error:

Invalid time set

Error:

Failure in time-of-year test

Error:

VRT bit failed to set after it was read the first time

Error:

Battery voltage level was down during the clock test

98 Self-Tests

B.13 MONO (test F)
The monochrome video display controller (MONO) power-up self-test has
one longword of status information in the following format:
MONO

0000.0XXX

where XXX is one of the status or error codes listed in the following table:
Code

Status

Definition

Status:

Success

Error:

Memory byte mask failure

Error:

Memory error

Error:

End-of-frame bit not in interrupt pending register

Error:

End-of-frame failed to set for second time

Error:

End-of-frame failed to set for third time

Error:

No end-of-frame interrupt seen

100

Error:

Wrong IPL level for EOF interrupt

200

Error:

Interrupt request failed to clear interrupt pending register
bit

400

Error:

End-of-frame interrupt not seen when looking at the
interrupt request register

800

Error:

Error during cursor test

1000

Error:

VDCSEL register read/write failure

C
System Tests
C.1 Error and Status Codes for the VS3100 System
Test
In all cases, when examining the exerciser report, a single question mark
(?) indicates a nonfatal error, a double question mark (??) indicates a
fatal error, and the absence of question marks indicates success.
The system software error codes are as follows:
FFFE.xxxx -- A device control block was found which did not have
a valid pointer to a system level test module.
FFFD.xxxx -- A system level test module failed to respond within
the designated time period.

C.2 Ethernet Subsystem Status and Error Codes
TEST NUMBER ID NAME
----------- ---- ---1 00C0 NI
000x.yyyy

x
is subtest number
yyyy is error code

For x values, the testing being performed:
1. Verifies LANCE interrupt on initialization done
2. Performs internal loopback testing
3. Displays Ethernet subsystem status and error codes
4. Verifies multicast filtering and promiscuous receive

100 System Tests

5. Forces collision error
6. Forces MISS error
7. Performs external loopback testing
For yyyy values, the corresponding error is:
0002

No packet received

0004

Packet data miscompare

0006

Wrong received CRC

0008

Initialization failed

000A

Received a packet with bad CRC

000C

CRC flag was not set when forced

000E

Received an illegal multicast packet

0010

Rejected a packet when in promiscuous mode

0012

Rejected a legal multicast packet

0014

RTRY not set when forced

0016

BUFF not set when forced

0018

MISS not set when forced

001A

Transmit error

001C

Transmit timeout

System Tests 101

C.3 8-Plane Video Option Status and Error Codes

TEST NUMBER ID NAME
----------- ---- ---4 00D0 8PLN
00yy.xxxx Where :
for soft error ( one question mark is displayed)
yy = soft error - video readback (should be 20 or 21)
xxxx = 0
for hard error ( 2 question marks are displayed)
yy = status code for test that failed
xxxx = error from exerciser error codes
Test numbers:
------------program initialization
02
FCC RAM
03
FCC fifo control
04
dragon initialization
05
dragon timing chip
06
video memory
07
ID bus data path
08
FCC data transfers
09
byte packing
10
byte packing ( burst mode )
11
compression
12
transfer display list command 13
display list commands
14
interrupts
15
cursor
16
VDAC read/write
17
scrolling
18
scrolling ( burst mode )
19
video readback
20
cursor readback
21
left edge readback
22
right edge readback
23
sync readback
24

102 System Tests

Status codes:
------------err$_vse_init_failed
err$_kernel_allocate_failed
err$_create_device_1_failed
err$_create_device_2_failed
err$_poll_failed
err$_data_path_failed
err$_fifo_path_failed
err$_fifo_empty_bit
err$_fifo_full_bit
err$_fwlt0_wrong
err$_fwused_wrong
err$_athere_wrong
err$_adder_scans
err$_viper_init
err$_adder_init
err$_update_enable
err$_memory_read
err$_plane
err$_data_path_crc
err$_data_path_compare
err$_scroll_right_crc
err$_scroll_right_compare
err$_scroll_up_crc
err$_scroll_up_compare
err$_scroll_left_crc
err$_scroll_left_compare
err$_scroll_down_crc
err$_scroll_down_compare
err$_fcsr_not_thresh
err$_fcsr_not_empty
err$_get_ne_put
err$_fcc_transfer_crc
err$_fcc_data_wrong
err$_fcc_address_wrong
err$_fcc_tx_noadder
err$_fcc_no_tx_adder
err$_fcc_transfer_compare
err$_vdac_read_failed
err$_vdac_data_failed_a
err$_vdac_data_failed_b
err$_vdac_address_failed_a
err$_vdac_address_failed_b
err$_vdac_address_failed_c
err$_vdac_init
err$_compare_bitmap_failed
err$_read_bitmap_failed
err$_fcc_register_failed
err$_fifo_control_failed

01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30

System Tests 103

err$_ptb_unpack
err$_btp_pack
err$_btp_pack_wrong
err$_fcc_no_idle_interrupt
err$_fcc_no_thresh_interrupt
err$_cursor_test_bit
err$_cursor_test_timeout
err$_adder_interrupt_timeout
err$_fcc_interrupt_timeout
err$_no_sys_request
err$_sys_request
err$_no_interrupts
err$_wrong_count
err$_fcc_no_thresh_request
err$_fcc_thresh_interrupt
err$_wrong_csr_address
err$_fcc_thresh_request
err$_dlc_1
err$_dlc_2
err$_dlc_3
err$_dlc_4
err$_dlc_5
err$_dlc_6
err$_dlc_7
err$_dlc_8
err$_dlc_9
err$_dlc_10
err$_dlc_11
err$_dlc_12
err$_dlc_13
err$_foreground_map
err$_background_map
err$_cursor_a_map
err$_cursor_b_map
err$_ptb_fcc_wrong_bits
err$_video_readback
err$_cursor_readback
err$_no_sync
err$_decompression
err$_comp_fifo
err$_short_display_list
err$_right_readback
err$_left_readback
err$_sync
err$_ptb_dlc
err$_btp_diag_failed_a
err$_btp_diag_failed_b
err$_fcc_bitmap_compare_a
err$_fcc_bitmap_compare_b
err$_rdbk_1

31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62

104 System Tests

err$_rdbk_2
err$_rdbk_3
err$_rdbk_4
err$_rdbk_5
err$_rdbk_6
err$_cursor_test_true
err$_cursor_test_false
err$_vertical_sync

63
64
65
66
67
68
69
6A

err$_init_adder_scans
err$_viper_initialization
err$_adder_initialization
err$_fill_bitmap_area
err$_quick_bitmap_read
err$_read_bitmap
err$_compare_bitmap
err$_fcc_compare

100
200
300
400
500
600
700
800

err$_viper_register_load
err$_viper_z_load
err$_chip_select
err$_poll

1000
2000
3000
4000

EXERCISER TEST ORDER
NONBURST MODE, FIRST PASS
fcc ram data and address
fcc passive fifo control
dragon chips initialization
dtc chip select
quick video ram
id bus data path
fcc unpacking
interrupts
vdac
scrolling
short display list
processor to bitmap display
list command
cursor
fcc compression algorithm
video readback

System Tests 105

NONBURST MODE, NOT FIRST PASS
fcc ram data and address
fcc passive fifo control
dragon chips initialization
dtc chip select
quick video ram
id bus data path
interrupts
vdac
short display list
processor to bitmap display
list command
video readback

BURST MODE
If customer mode:
fcc unpacking
scrolling
cursor
fcc display list commands
fcc compression algorithm

If manufacturing mode (loopbacks), then the burst mode testing is broken
up into two groups that get executed on every other burst mode pass. This
was done to decrease the amount of time that each pass spends on the
color module, and hopefully, eliminate any timeouts that manufacturing
was seeing with the 4-plane.
Group 1:
fcc_unpacking
scrolling
display list commands
fcc compression algorithm
Group 2:
cursor

106 System Tests

C.4 SCSI-B Status and Error Codes

TEST NUMBER ID NAME
----------- ---- -----6 00A0 SCSI B

The first line of the SCSI-B report:
STATUS
x

ERROR
x

1
Always 1
Result of Buffer Test
Result of Register Test
Result of Interrupt Test
Transfer Test Error Count
Result of Transfer Test
Transfer Device

Result of Buffer Test: This position will contain a value from Table C–1.
Result of Register Test: This position will contain a value from
Table C–1.
Result of Interrupt Test: This position will contain a value from
Table C–1.
Transfer Test Error Count: This position will contain the number of
transfer test errors.
Result of Transfer Test: This position will contain a value from
Table C–1.
Transfer Device: This position will contain the ID of the SCSI-B device
used. This value is ’F’ during the first pass, and ’8’ if unable to use any
device as a transfer device.

System Tests 107

Subsequent lines of the SCSI-B report:
STATUS
x

ERROR
x

1
Always 1
Routine Status
Device Status
Last Command
Error Count
Removable / Writeable
SCSI−B ID of Device

Routine Status: This position will contain a value from Table C–1.
Device Status: This position will contain a value from Table C–2.
Last Command:
0
1
2
3
4
5
6
7

- com$unitready
- com$requestsense
- com$inquiry
- com$senddiagnostics
- com$recdiagnostics
- com$read
- com$write
- com$rewind

Removable/Writeable:
1
2

- Removable
- Writeable

SCSI-B ID of Device: This position will contain the ID on the SCSI-B
bus of the device (that is, its address on the SCSI-B bus).

108 System Tests

Table C–1 SCSI-B Error and Status Summary
Value

Error

Success

Controller error:
DMA bit will not set in the SCSI-B controller mode register.
Target command register not valid.
Initiator command register not valid.
Bus free not valid.
Phase match bit in bus and status register not valid.
Interrupt request bit in bus and status register not valid.

Data path error:
Data path in longword, word, or byte access failed; unable to access all
of data buffer.
Unable to reach SCSI-B controller; unable to write to mode register.

DMA count error:
Count register not verified.
Count not 0 after DMA transfer.

Timeout error:
No phase match within timeout period.

Interrupt error:
Interrupt not received when expected.
An error occurred while testing the system interrupt logic.

Unexpected interrupt error:
Unexpected interrupt received.

Command error:
Request sense command ended without sense data. Command
terminated with bad device status.

Phase error:
Unexpected phase or phase change on SCSI-B bus.

Buffer overflow error:
Too many bytes read from target.

System Tests 109

Table C–1 (Cont.) SCSI-B Error and Status Summary
Value

Error

Arbitration error:
AIP bit in initiator command register not set during arbitration process,
or arbitration lost during arbitration process, or arbitration not won.

Target will not set BSY during selection process, or the SCSI-B is busy
at start of register test, or the INI_CMD<BSY>bit could not toggle
during the register test.

Unable to loop data out onto SCSI-B bus and back in again.

Direction and phase of SCSI-B bus, as set by the target and read from
the controller, are incompatible.

SCSI-B bus will not drop REQ within timeout period, or SCSI-B bus will
not assert REQ within timeout period.

DMAEND bit not verified in bus and status register, or DMA data not
matching expected data.

Table C–2 SCSI Device Status
Code

Definition

Ready - SCSI device is on-line and ready for commands.

Off-line - Status given to SCSI ID devices that will not respond to
selection process, or status given to all devices for initialization.

Not ready - Status given to devices that are selectable, but return a not
ready status during status phase of a command (command tried five
times).

Diagnostic error - Device returned an error status after a self-test.

Key error - Unable to rewrite Customer Services key on removable
media sequential device.

110 System Tests

C.5 SCSI-A Status and Error Codes
TEST NUMBER ID NAME
----------- ---- -----7 0090 SCSI A

The first line of the SCSI-A report:
STATUS
x

ERROR
x

1
Always 1
Result of Buffer Test
Result of Register Test
Result of Interrupt Test
Transfer Error Count
Result of Transfer Test
Transfer Test Drive Number

Result of Buffer Test: This position will contain a value from Table C–3.
Result of Register Test: This position will contain a value from
Table C–3.
Result of Interrupt Test: This position will contain a value from
Table C–3.
Transfer Error Count: This position contains a count (in hex) of the
number of errors that have occurred during the transfer test.
Result of Transfer Test: This position will contain a value from
Table C–3.
Transfer Test Drive Number: Number of the drive used for the transfer
test. Value ID F if no drive is available.

System Tests 111

Subsequent lines of the SCSI-A report:
STATUS
x

ERROR
x

1
Always 1
Routine Status
Termination Code
Chip Status
Drive Error Count
Drive Status
Device ID of Drive

Routine Status: This position will contain a value from Table C–3.
Termination Code: This position will contain the TERMCOD bits of the
interrupt status port register.
Chip Status: This position is divided into four binary bits.
Revectored BB = VALUE F
Error occurred while revectoring = VALUE E
Ecc error = 4 \
Sync error = 2 > Bit field
Cmp error = 1 /
Drive Error Count: This position will contain the number of errors for
this drive.
Drive Status: This position is also divided into three binary bits.
WRITEABLE = 4
UIB and RCT = 2
FORMATTED = 1
Device ID of Drive: This position will contain a number between 0 and
3. It will represent the ID of the drive.

112 System Tests

Table C–3 SCSI-A Error and Status Summary
Value

Error

Success

Registers 0, 1, 2, or 3 not completely verified, rtcnt, invrdy, intrdch,
ready, presdrv, int_done selack(l), skcom(h) not verified.

Data path error:
Data path in longword, word, or byte access failed; unable to verify all
of data buffer or data path to register 10 not verified.

DMA count error:
Count register not verified.
Count not 0 after DMA transfer.

Command not finished before timeout.

Error in system interrupt logic.

Unexpected interrupt before command issued.

Command terminated with bad status.

Restore command terminated with error status.

Step command terminated with error status.

Seek command terminated with error status.

Read command terminated with error status.

Write command terminated with error status.

Unable to verify register sequencing in 9224.

Drive not formatted (UIB, RCT not found. Bad media).

Data checksum incorrect in transfer test.

System Tests 113

C.6 SCSI-A Error Explanations
MEDIA PROBLEMS
For the 1st line of the report, any error that looks like this could be a
media error:
XBYY.0001 Read Error
XCYY.0001 Write Error

where X is the transfer unit and YY is the error count
For the 2nd, 3rd, or 4th line reported (that is, the device status), the
following codes indicate a media error:
XZYY.STA1
XZYY.STB1
XZYY.STC1

Seek Error
Read Error
Write Error

where:
X = Drive number
Z = Drive status
YY = Error count
S = Chip status
T = Termination code

CONTROLLER PROBLEMS
The following error codes are probably caused by controller problems.
They will occur in the 1st line of the error report.
XXXX.ABCD

where XXXX is a don’t care situation and if A, B, C, D are anything except
0.

114 System Tests

CONTROLLER OR DRIVE PROBLEMS
The following errors could be controller or drive problems. They will occur
in the 2nd, 3rd, or 4th line of the error report:
XZYY.ST81 Restore Error
XZYY.ST91 Step Error

where:
X = Drive number
Z = Drive status
YY = Error count
S = Chip status
T = Termination code (this must be a nonzero value)

If these errors only occur on one drive in a multidrive system, then the
error is probably in the drive. If these errors occur on all the drives, then
the error is probably in the controller. There was a bug in the earlier
versions (REV J and back) that reported a RESTORE ERROR with a
termination code equal to 0. This should be fixed in the later versions.
If you see this error in versions after REV J, report it to the diagnostic
group.
CONTROLLER OR MEDIA PROBLEMS
This error could be a problem with the media or the controller. It will be
seen on the 1st line of the error report:
XFYY.0001 CRC/ECC error

where X is the transfer unit and YY is the error count.

System Tests 115

C.7 Memory Status and Error Codes

TEST NUMBER ID NAME
----------- ---- ---B 0010 MEM
Status.error
Meaning
-----------------0000.0001 Success
0001.000F System software error
0002.000F System software error
0003.000F System software error
0004.000F System software error
0005.000F System software error
0006.000F System software error
0007.000F System software error
0008.000F System software error
0001.001F Compare error on system board
0002.001F Compare error on option board
0001.002F Parity error on system board
0002.002F Parity error on option board

When there is no error, the status word will reflect the number of 512
byte memory pages tested at the time of the report.
The monochrome status and error code display line is complimented with
another field, progress reporting. Progress reporting is a four "nibble"
wide field (just after the error field) that gives an indication of progress of
the test module by increasing its count from zero after the first pass and
during each subsequent pass. The progress count is always initialized at
the beginning of each pass.
NOTES
System software errors are indicated with codes xxxx.000F.
When there is no error, the status word will reflect the number of
512 byte memory pages tested at the time of the report.

116 System Tests

C.8 DZ Controller Status and Error Messages
TEST NUMBER ID NAME
----------- ---- ---C 0080 DZ

All errors detected during the DZ system exerciser are considered to
be fatal. If the exerciser is being executed in Customer Services or
manufacturing mode, then loopback connectors are required on the
appropriate ports. If an error is detected during these modes, check that
the loopbacks are installed before changing the system module.
Error messages will be displayed as follows:
0LSS.EEEE

The error message is broken up into two fields. The first field, ’0LSS’,
represents the status word. The second field, ’EEEE’, represents the
error code.
The status word portion of the error message from this test will be broken
into two fields. The upper byte, ’0L’, will indicate the line preempted by
the console. The lower byte, ’SS’ will give additional information on the
error code as follows:
Status
Code

Meaning

The error code is broken into four fields with each digit of the error code
corresponding to one line on the DZ. The least significant four bits of the
error code represents line 0.

Device fatal error. The entire error code indicates the error.

System software error. The entire error code indicates the error.

Error descriptions for status code = 0:
0X00.ABCD

where X represents the line preempted by the console and A, B, C, D
represents a 4-bit error field for each line. ’A’ represents 4 bits for line
3, ’B’ represents 4 bits for line 2, ’C’ represents 4 bits for line 1, and
’D’ represents 4 bits for line 0.

System Tests 117

A description of the 4-bit error codes are described in the following table:
Error
Code

Meaning

No error detected for this line
** Error codes testing all lines simultaneously **.

No character received.

Failed to transmit all characters, or transfer took too long, or lost
receive characters.

Too many characters received.

Character received not equal expected.

Parity, framing, or overrun error detected
** Error code testing baud rates on line 2 **.

Baud rate timing error
** Error code testing modem signals through loopback connector **.

Modem signals not equal expected
** Error codes testing each line for overrun errors **.

Overrun error not equal 0.

Character received not equal expected.

Overrun error failed to set
** Error codes testing each line for framing errors **.

Framing error failed to set
** Error codes testing transmit flag and interrupt request **
** Register for each line. **.

TxRdy bit failed to set.

Transmit line received not equal expected.

Interrupt request bit ST not set in INT_REQ register.

Interrupt request bit ST not cleared in INT_REQ register.

118 System Tests

Error descriptions for status code = FF
0XFF.EEEE

where:
X represents the line preempted by the console
FF represents a device fatal error
EEEE represents the error code
Error Code
----------

Meaning
-------

** Initial Startup code **
0001 - Interrupt Mask Register, INT_MSK,
register bits ST or SR stuck at 1
** Error Codes in READ_WRITE_REGISTER_TEST **
0002 - Master clear failed to reset DZQ
0003 - CSR register <> expected %x1028
0004 - CSR register failed to clear
0005 - TCR register <> expected %x0F0F
0006 - TCR register failed to clear
** Error Codes in INTERRUPT_BITS_TEST **

System Tests 119

0007 - TRDY bit in CSR stuck at 1
0008 - TRDY bit in CSR failed to set
0009 - TRDY bit in CSR failed to clear
after transmitting a character
000A - TRDY bit in CSR failed to set
after transmitting a character
000B - RDONE bit failed to set after
transmitting character in internal
loopback mode.
000C - SR bit in INT_REQ register not set
by RDONE
000D - SR bit in INT_REG register not cleared
by writing bit in INT_CLR register
000E - Character received <> ’0’ or line
number not equal expected
000F - Data valid bit not set in word read
0010 - Silo Alarm Enable failed to set in CSR
0011 - Silo Alarm failed to set after transmitting
16 characters in internal loopback
0012 - RDONE not set after 16 characters received
0013 - SR bit in INT_REQ register not set by
Silo Alarm
0014 - Silo Alarm failed to clear after reading
a character from Silo
0015 - Master clear failed to reset the DZQ
0016 - Unexpected transmit interrupt occurred with
Interrupt Mask bit cleared.
0017 - Unexpected receive interrupt occurred with
Interrupt Mask bit cleared.
** Error Codes for BASIC_INTERRUPT_TEST **
0018 - INT_MSK register bit ST failed to set
0019 - Failed to receive a transmit interrupt
001A - Transmit interrupt occurred with INT_MSK
bit ST cleared
001B - INT_MSK register bit SR failed to set
001C - Failed to receive a receive interrupt
001D - Receive interrupt occurred with INT_MSK
bit SR cleared.
** Error Codes in BREAK_DETECT_TEST **
001E - TRDY failed to set after setting
line enable for line in TCR register
** Error Codes in OUTPTR_CHAR_POLLED **
001F - TRDY failed to set in allotted time

120 System Tests

Error descriptions for status code = 0F:
0X0F.EEEE

where:
X represents the line preempted by the console
0F represents a system software error
EEEE represents the error code

The error codes for this type of error range from 0001 to 000B. These
errors are detected after making calls to the system exerciser monitor.
They will be considered system software errors and considered to be fatal.

C.9 Monochrome Display Status and Error Codes

TEST NUMBER ID NAME
----------- ---- ---F 00B0 MONO
Status.error
Meaning
-----------------0001.F001 System software error
0001.F002 System software error
0001.F003 System software error
0001.F004 System software error
0001.F005 System software error
0001.F006 System software error
0000.0001
No errors
0001.0002
VDC register error
0001.0003
Screen memory error
0001.0004
Unexpected end-of-frame interrupt
0001.0005
No end-of-frame interrupt
0001.0006
Interrupt register error
0001.0007
Cursor chip error

A system software error may indicate a corrupted ROM.
The monochrome status and error code display line is complimented with
another field, progress reporting. Progress reporting is a four "nibble"
wide field (just after the error field) that gives an indication of progress of
the test module by increasing its count from zero after the first pass and
during each subsequent pass. The progress count is always initialized at
the beginning of each pass.

D
Diagnostic LEDs Definitions
This appendix defines the eight LEDs on the back of the system box
during each phase of the testing and power-up initialization. The LEDs
are divided into two fields. The first four LEDs indicate the current state
of the system and the second set of four depend on the previous four.
There are sixteen possible combinations for each set of LEDs. The four
LEDs that indicate the state of the system have the following definitions.
The other four LEDs have another meaning as indicated in Table D–1.
The number 1 indicates the LED is lit.
Table D–1 Diagnostic LEDs Definitions
State

Substate Definitions

Recommendations

1111

Power is applied but no
instruction is executed.

See Section D.1

1111

0000

Power is applied. The ROM
code is successfully started
and several instructions
have been executed.

See Section D.1

1110

0000

Console memory sizing
routine is entered. Memory
to hold the console data
structures is located. The
substate variables have no
meaning in this section of
the test.

See Section D.1

1101

0000

The console data structures
are initialized and have
started testing the NVR.

See Section D.1

1100

0000

The NVR test completed
and the DZ test has started.

See Section D.1

121

122 Diagnostic LEDs Definitions

Table D–1 (Cont.) Diagnostic LEDs Definitions
State

Substate Definitions

Recommendations

1011

0000

The DZ test completes. An
optional video has been
found but its testing has not
been started. This is part of
the console determination
code.

See Section D.1

1011

0001

The DZ test completes. No
optional video is installed
or, if it is installed, fails
self-test. In either case, the
base monochrome video test
has been entered.

See Section D.1

1010

0000

The video subsystem was
tested and the console
initialization sequence was
entered.

See Section D.1

1001

xxxx1

The system initializes and
power-up testing starts.
The substate variable
indicates the test being
executed.

If the substate contains
any lit LEDs, determine
the failing device. If you
have operational video,
troubleshoot that device.
If the video screen is
blank, you have a dead
system. See Section D.1.

1000

xxxx1

The self-test completes with
the substate indicating the
failing subsystem.

Enter TEST 50 to see the
results

0111

xxxx1

Self-test was entered from
the console TEST command.
The substate indicates
the test currently being
executed.

Enter TEST 50 to see the
results.

0110

xxxx1

The self-test completes from
the TEST command with
the substate indicating the
failing subsystem.

Enter TEST 50 to see the
results.

1 1111 = MONO, 1110 = CLK, 1101 = NVR, 1100 = DZ,1011 = MEM

1001 = FP, 1000 = IT, 0111 = SCSI-A or SCSI-B
0110 = SCSI-A or SCSI-B, 0101 = SYS, 0100 = 8PLN, 0011 = (option)
0010 = (option), 0001 = NI

Diagnostic LEDs Definitions 123

Table D–1 (Cont.) Diagnostic LEDs Definitions
State

Substate Definitions

Recommendations

0101

xxxx1

The self-test started under
control of the APT system.
The substate indicates
the test currently being
executed.

Enter TEST 50 to see the
results.

0100

xxxx1

The system exerciser
started from a console TEST
command. The substate
indicates the value of
the lower four bits of the
command. If the system
exerciser starts with a
T 101, the substate contains
a 1 (hexadecimal).

Read the test results on
the screen. Troubleshoot
the failing device.

0011

0000

The system exerciser
started under control of the
APT test delivery system.

Read the test results on
the screen. Troubleshoot
the failing device.

0010

xxxx1

The entity-based module
received a request from a
host to enter monitor mode.
This lets the host send
commands to the system.
This is indicated if the
functionality of the EBM
is implemented at a later
release of the ROM.

Reserved for future use.

0001

xxxx1

Console mode was
successfully entered
and is ready to accept
commands. This does not
apply to power on. The
substate indicates the
failing subsystem if there
is one. This differs from a
self-test complete, because
the console can be entered
by other means.

This code indicates that
the console was entered
from something other
than a TEST command or
power on halt, such as the
HALT button.

1 1111 = MONO, 1110 = CLK, 1101 = NVR, 1100 = DZ,1011 = MEM

1001 = FP, 1000 = IT, 0111 = SCSI-A or SCSI-B
0110 = SCSI-A or SCSI-B, 0101 = SYS, 0100 = 8PLN, 0011 = (option)
0010 = (option), 0001 = NI

124 Diagnostic LEDs Definitions

Table D–1 (Cont.) Diagnostic LEDs Definitions
State

Substate Definitions

Recommendations

0000

xxxx

System is booting.

Attempting to boot the
system. Once control passes
to VMB, the state LEDs
have no meaning.

Figure D–1 shows the LEDs on the back of the system box.

State

Substate
LJ-00734-TI0

Figure D–1

LED Layout

D.1 Additional LED Information
When the system does not power up successfully or if the diagnostics find
an error, the eight LEDs on the back of the system box usually indicate
the failing device (the system takes 2 to 5 minutes to complete power-up
initialization and testing). However, if the four state LEDs indicate 1111
(F in hexadecimal) through 1010 (A in hexadecimal, the substate LEDs
offer no help in determining the failing FRU. You must disconnect a FRU
as described in each step in the following procedure until the system does
power up normally. Once the system does power-up normally, the last
FRU you disconnected is the failing FRU. Replace the failing FRU and
retest the system for any further problems.
1. Power down the system. Remove the system box cover, disconnect
the cable connecting the system module to the MSC module, and
disconnect the power cables to the drives. This disconnects the MSC
module and all of the drives from the system.
2. Power up the system with the MSC module disconnected. If the
system still does not power up properly, the problem is not with the
drives or the MSC module, then proceed to step 3. If the system does
power-up successfully after disconnecting the MSC module, replace
the MSC module and retest the system.

Diagnostic LEDs Definitions 125

3. Power down the system, remove drive mounting panel(s) from the
system, and remove the graphics module from the system module. If
the graphics module was not installed, then proceed to step 5. When
you power-up the system after removing the graphics module, you
must either connect an alternate console terminal to the printer port
and set S3 to the up position (9600 baud rate) or watch the LEDs to
see if the system does or does not power up successfully. The alternate
console is used to display the video because there is no video signal
output to the monitor when the graphics module is disconnected.
4. Power-up the system with the graphics module disconnected. If the
system still does not power up properly, the problem is not in the
graphics module, then proceed to step 5. If the system does power up
successfully, replace the graphics module and retest the system.
5. Power down the system, remove the memory module from the system
module.
6. Power up the system with the memory module disconnected. If
the system does not power up properly, the problem is not the
memory module, then proceed to step 7. If the system does power
up successfully, replace the memory module and retest the system.
7. Power down the system. Replace the system module and power up
the system again. If the system still does not power up properly after
replacing the system module, replace the power cable.

Index
C
Command codes
PV_SCS_FMT_ERR#, 23
Console
password feature, 27
Console’s configuration display
utility, 77
CLK, 97
COLOR, 80
DZ, 95
FP, 94
IT, 93
MEM, 94
MONO, 98
NI, 77
NVR, 97
SCSI-A, 93
SCSI-B, 83
SYS, 82
Contents
system, 33
Cover removal
system box, 39 to 40

D
Diskette formatter, 20
messages, 21
Disk formatter
diskette example, 20
Documentation
conventions, xi
ordering, x
related, x

Documentation (Cont.)
video monitor, 37
Documents
related, x
video monitor, 37
Drive plate
removal, 55

E
Equipment required, x
Error and status codes for PVAX
system test
DZ controller, 116
Ethernet subsystem, 99
memory, 115
monochrome display, 120
8-plane video option, 101
SCSI-A, 110
SCSI-B, 106
Error and status codes for VS3100
system test, 99
Error codes
PV_SCS_FMT_ERR#, 23 to 25
Ethernet ID ROM
removing/replacing, 65

F
FRU, 37
FRU removal and replace
procedures, 36

Index 1

2 Index

Graphics coprocessor module
removal, 60
Graphics Coprocessor Module
Selection 60Hz/66Hz, 61

Locating failed memory bank, 11
Loopback connectors, 5

Password
enable, 29
examples
invalid, 29
valid, 29
feature, 27
status, 31
Power-up testing
error codes, 3
example display, 2
summary display, 2
PVST, 99
DZ controller, 116
Ethernet subsystem, 99
memory, 115
monochrome display, 120
8-plane video option, 101
SCSI-A, 110
SCSI-B, 106
PV_SCS_FMT_ERR# Error Codes,
23 to 25

H
Halt button
location, 34

J
Jumpers
RZ22, RZ23, RZ23L, RZ24, 47
SCSI ID, 47

Memory modules
error code for MEM, 12
removal, 62
Model 76
enclosure description, 33
FRU removal and replacement
procedures, 36
keyboard, 70
mouse and tablet, 72
power supply, 69
identification, 1
Monitor
documentation, 37
Monitors, 34

Recommended spares list, 73
Related documents, x
RX23 disk drive
removal, 50
RZ22/24 disk drive
removal, 41 to 49

S
SCSI
jumpers, 47
SCSI device
SCSI-A system exerciser code, 16
SCSI/FDI adapter
switches, 52
Self-test

Index 3

Self-test (Cont.)
error codes, 6
example display, 5
running, 5
with loopback connectors, 5
using loopback connectors, 5
Self-test commands, 3, 5
SIMM
error code for MEM, 12
Special key for system exerciser
diskette example, 26
Special key on diskettes for system
exerciser, 25
Switches
SCSI/FDI adapter, 52
System box
cover removal, 39 to 40
System exerciser
commands, 7
error codes, 7
System exerciser diagnostics, 6
System module
removal, 64
replacement, 66

T
T 50, 77
CLK, 97
COLOR, 80
DZ, 95
FP, 94
IT, 93
MEM, 94
MONO, 98
NI, 77
NVR, 97
SCSI-A, 93
SCSI-B, 83
SYS, 82
Testing, 1
power-up, 2
self-test, 5
self-test commands, 5

Testing (Cont.)
system exerciser, 6
Time-of-Year chip, 27
Tools required, x
TOY chip, 27
Troubleshooting, 9
memory (MEM), 9
RX23 self-test, 13
RX23 self-test results, 13
RX23 system exerciser, 15

U
Utilities, 19
commands, 19
diskette formatter, 20
special key on diskettes for
Customer Services system
exerciser, 25
test number, 19 to 20

V
VAXstation 3100 Model 76
connectors, 34
Video monitor
documentation, 37
Video monitors, 34