Digital PDFs

EK-MV489-Ul

November 1996

172 pages

Original

1.8MB

Document:	MicroVAX 3100 Models 88/98 User Information
Order Number:	EK-MV489-Ul
Revision:	000
Pages:	172
Original Filename:	https://manx-docs.org/collections/mds-199909/cd1/vax/mv489uia.pdf

OCR Text

MicroVAX 3100 Models 88/98
User Information
Part Number: EK-MV489-UI. A01

November 1996

This book introduces the MicroVAX 3100 Model 88 and Model 98 systems. Use the
information in this book to configure, start, use, update, and troubleshoot your system.
You will also find general system information, such as console commands and system
care in this book.

Revision/Update Information:

Digital Equipment Corporation
Maynard, Massachusetts

This is a new manual.

First Printing, November 1996
Digital Equipment Corporation makes no representations that the use of its products in the manner described in this
publication will not infringe on existing or future patent rights, nor do the descriptions contained in this publication
imply the granting of licenses to make, use, or sell equipment or software in accordance with the description.
Possession, use, or copying of the software described in this publication is authorized only pursuant to a valid
written license from Digital or an authorized sublicensor.
© Digital Equipment Corporation 1996. All rights reserved.
The following are trademarks of Digital Equipment Corporation: MicroVAX, OpenVMS, ThinWire, VAX, and the
DIGITAL logo.
The following are third-party trademarks:
SIMM is a trademark of Molex Corporation.
All other trademarks and registered trademarks are the property of their respective holders.
[S3266]

Information - Class A

FCC NOTICE -- CLASS A DEVICE
Warning!
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Achtung!
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb
dieses Gerätes Rundfunkstörungen auftreten, in welchen Fällen der Benutzer für
entsprechende Gegenmaßnahmen verantwortlich ist.

Avertissement!
Cet appareil est un appareil de Classe A. Dans un environnement résidentiel cet appareil
peut provoquer des brouillages radioélectriques. Dans ce cas, il peut être demandé à
l'utilisateur de prendre les mesures appropriées.

Table of Contents
1 System Overview
Introduction..........................................................................................................................1-1
System Unit..........................................................................................................................1-2
Enclosure Front Panel....................................................................................................1-4
Enclosure Rear Panel.....................................................................................................1-6
System Components ......................................................................................................1-8
System Board .............................................................................................................. 1-10
Internal Signal Cable Routing ...................................................................................... 1-12
Internal Power Cable Routing ...................................................................................... 1-14
The Keyboard .............................................................................................................. 1-16

2 Getting Started
Introduction ...................................................................................................................2-1
Before Starting Your System .........................................................................................2-2
Converting the System to Lie Flat on the Desktop .........................................................2-3
Locking Your System ....................................................................................................2-4
Identifying the Correct AC Power Cord .........................................................................2-6
Installing Your System ..................................................................................................2-7
Connecting System Components.............................................................................2-9
Connecting the Console Terminal ...........................................................................2-9
Network Connection and Termination................................................................... 2-10
Selecting ThinWire or ThickWire Ethernet ...........................................................2-11
Connecting ThinWire Ethernet ............................................................................. 2-12
Connecting ThickWire Ethernet............................................................................ 2-14
Connecting a SCSI Cable or the SCSI Terminator................................................. 2-15
Connecting External Options to the System .......................................................... 2-16
Connecting Peripherals to a DEC423 MMJ Port.................................................... 2-16

MicroVAX 3100 Models 88/98 User Information v

Table of Contents
Connecting a Peripheral to the Asynchronous Modem Control Port ...................... 2-17
Connecting Peripherals to an Optional Asynchronous Port.................................... 2-20
Connecting Peripherals to a DHW42-CB Option .................................................. 2-22
Connecting Peripherals to an Optional Synchronous Port...................................... 2-24
Installing a SCSI Terminator on an Optional KZDDA .......................................... 2-26
Connecting the Power Cord .................................................................................. 2-27
Starting Your System............................................................................................ 2-28
Checking the Power-Up Test Results .................................................................... 2-29
Testing the Ethernet Installation ........................................................................... 2-31
Completing the Ethernet Installation..................................................................... 2-32
If the Network Installation Fails............................................................................ 2-32
Removing the System Unit from a Network.......................................................... 2-32
Removing the System Unit from a ThinWire Ethernet Cable ................................ 2-33
Removing the System Unit from a ThickWire Ethernet Cable .............................. 2-33
Booting the Operating System .............................................................................. 2-34
Turning Off Your System ..................................................................................... 2-34
Computer Security....................................................................................................... 2-34
Posture and Work Habits ............................................................................................. 2-34

3 Installing Hardware Options
Introduction................................................................................................................... 3-1
Removing the Cover...................................................................................................... 3-2
Cache Memory .............................................................................................................. 3-3
System Memory ............................................................................................................ 3-3
Memory Configuration Rules.................................................................................. 3-3
Installing or Removing Memory Modules (SIMMs)....................................................... 3-4
Storage Devices.................................................................................................................... 3-6
General Information on Installing Drives....................................................................... 3-6
SCSI Addresses (SCSI ID’s) ................................................................................... 3-7
SCSI Termination ................................................................................................... 3-7
External SCSI Connector Termination.................................................................... 3-7
Internal SCSI Termination ...................................................................................... 3-8
SCSI Bus Length .................................................................................................... 3-8
Installing Optional Storage Devices...................................................................................... 3-8
Installing Devices in the Front Bay................................................................................ 3-8
Installing a Hard Disk Drive in the Rear Storage Bay .................................................. 3-12
Communications Options ................................................................................................... 3-14
Synchronous Communication Option........................................................................... 3-15
Installing the Synchronous Communication Option .............................................. 3-15
Asynchronous Communication Options ....................................................................... 3-16
Installing the Asynchronous Communication Option ............................................ 3-17

vi MicroVAX 3100 Models 88/98 User Information

Table of Contents
Optional SCSI Port (KZDDA) .....................................................................................3-18
Installing the KZDDA........................................................................................... 3-19
External Options................................................................................................................. 3-20
Connecting an External SCSI Option or Expansion Box ..............................................3-20
System Board Access .........................................................................................................3-22

4 Troubleshooting
Introduction ...................................................................................................................4-1
Initial Troubleshooting ..................................................................................................4-1
General Troubleshooting................................................................................................4-2

5 Diagnostic Tests and Commands
Power-Up Tests ............................................................................................................ 5–1
Diagnostic Tests and Utilities ....................................................................................... 5–4
Power-Up Error Messages............................................................................................. 5–9
Example 1.............................................................................................................. 5–9
Example 2............................................................................................................ 5–10
Example 3............................................................................................................ 5–11
Example 4............................................................................................................ 5–12
Example 5............................................................................................................ 5–13
Example 6............................................................................................................ 5–14
Configuration Display................................................................................................. 5–14
Error Display .............................................................................................................. 5–17
Contacting Digital Services ........................................................................................ 5–17
Equipment Log ........................................................................................................... 5–18

APPENDIX
A Console Commands
Entering Console Mode ........................................................................................................ A-1
Console Commands.............................................................................................................. A-1
BOOT............................................................................................................................ A-2
CONTINUE................................................................................................................... A-3
DEPOSIT ...................................................................................................................... A-4
EXAMINE..................................................................................................................... A-5
FIND ............................................................................................................................. A-6
HALT............................................................................................................................ A-7

MicroVAX 3100 Models 88/98 User Information vii

Table of Contents

APPENDIX (continued)
HELP ............................................................................................................................ A-7
INITIALIZE................................................................................................................ A-10
LOGIN ........................................................................................................................ A-11
MOVE......................................................................................................................... A-11
NEXT.......................................................................................................................... A-13
REPEAT ..................................................................................................................... A-15
SEARCH..................................................................................................................... A-16
SET ............................................................................................................................. A-18
SHOW......................................................................................................................... A-20
START........................................................................................................................ A-22
TEST........................................................................................................................... A-23
UNJAM....................................................................................................................... A-24
X -- Binary Load and Unload ...................................................................................... A-24
Controlling the Console Serial Line............................................................................. A-26
(Comment) .................................................................................................................. A-26

B Console Security
Console Security Feature...................................................................................................... B-1
Entering Console Mode ........................................................................................................ B-1
Setting the Security Password............................................................................................... B-1
Enabling the Console Security Feature .......................................................................... B-2
Logging in to Privileged Console Mode......................................................................... B-3
Changing the Security Password.................................................................................... B-4
Disabling the Console Security Feature ......................................................................... B-5
Exiting from Privileged Console Mode.......................................................................... B-5

C Setting the Defaults
Setting the Default Boot Device ........................................................................................... C-1
Setting the Default Recovery Action .................................................................................... C-2

viii MicroVAX 3100 Models 88/98 User Information

Table of Contents

APPENDIX (continued)
D System Care
Introduction.......................................................................................................................... D-1
Cleaning Your System Unit .................................................................................................. D-1
Cleaning Your Terminal ....................................................................................................... D-1
Cleaning Your Keyboard ...................................................................................................... D-2
Moving Your System............................................................................................................ D-2
Packing Your System ........................................................................................................... D-2
Installing Your System at a New Location............................................................................ D-3

E Technical Specifications
Introduction.......................................................................................................................... E-1
System Unit Specifications ................................................................................................... E-1

F Setting SCSI IDs
Selecting Available SCSI IDs on the System .........................................................................F-1

G Equipment Log
Introduction.......................................................................................................................... G-1
Equipment Log..................................................................................................................... G-1

MicroVAX 3100 Models 88/98 User Information ix

Table of Contents

LIST OF FIGURES
Figure 1-1 Front Controls, Indicators and Drive Bay Locations ............................................ 1-4
Figure 1-2 Rear Connectors (Rear View)............................................................................. 1-6
Figure 1-3 System Unit Components .................................................................................... 1-8
Figure 1-4 System Board Components................................................................................ 1-10
Figure 1-5 Internal SCSI Cable Routing ............................................................................. 1-12
Figure 1-6 Internal Power Cable Routing............................................................................ 1-14
Figure 1-7 Typical Keyboard Layout.................................................................................. 1-16
Figure 2-1 MicroVAX 3100 Model 88/98 System ................................................................ 2-2
Figure 2-2 Desktop Configuration ........................................................................................ 2-3
Figure 2-3 Removing the Front Door.................................................................................... 2-4
Figure 2-4 Removing the Cover............................................................................................ 2-5
Figure 2-5 Installing the Hasp............................................................................................... 2-6
Figure 2-6 System Enclosure Airflow................................................................................... 2-8
Figure 2-7 Connecting the Console Terminal ..................................................................... 2-10
Figure 2-8 Selecting the ThinWire or ThickWire Ethernet.................................................. 2-11
Figure 2-9 Assembling the ThinWire Ethernet Connector................................................... 2-12
Figure 2-10 Installing the ThinWire Ethernet ..................................................................... 2-13
Figure 2-11 Installing ThickWire Ethernet ......................................................................... 2-14
Figure 2-12 Connecting the SCSI Terminator..................................................................... 2-15
Figure 2-13 Connecting Peripherals to a DEC423 MMJ Port .............................................. 2-17
Figure 2-14 Connecting an EIA Connector to the Asynchronous Port................................. 2-18
Figure 2-15 Connecting a DEC423 Connector to the Asynchronous Port............................ 2-19
Figure 2-16 Connect a DHW42-BB Asynchronous Port...................................................... 2-21
Figure 2-17 Connecting to a DHW42-CB Asynchronous Port............................................. 2-23
Figure 2-18 Connecting to a DSW43-AA Synchronous Port ............................................... 2-25
Figure 2-19 Installing a SCSI Terminator on an Optional KZDDA..................................... 2-26
Figure 2-21 Turning the System On.................................................................................... 2-28
Figure 2-22 Recommendations for Posture and Work Habits.............................................. 2-35
Figure 3-1 Removing the Cover............................................................................................ 3-2
Figure 3-2 SIMM Bank Configuration.................................................................................. 3-4
Figure 3-3 Removing the SIMM Board ................................................................................ 3-5
Figure 3-4 Removing/Installing a SIMM Board.................................................................... 3-6
Figure 3-5 Installing the 3.5 Inch Brackets ........................................................................... 3-9
Figure 3-6 Removing the Front Bezel................................................................................. 3-10
Figure 3-7 Installing Optional Devices in the Front Bay ..................................................... 3-11
Figure 3-8 Removing the Rear Drive Bay........................................................................... 3-12
Figure 3-9 Installing Optional Hard Drives in the Rear Bay................................................ 3-13
Figure 3-10 Communication Slots ...................................................................................... 3-14
x MicroVAX 3100 Models 88/98 User Information

Table of Contents

LIST OF FIGURES (continued)
Figure 3-11 Installing the Synchronous Communication Option ......................................... 3-16
Figure 3-12 Installing the Asynchronous Communication Option .......................................3-18
Figure 3-13 Installing the KZDDA External SCSI Option................................................... 3-19
Figure 3-14 Removing System Board ................................................................................. 3-22
Figure 3-15 Removing the System Board Cover .................................................................3-23

MicroVAX 3100 Models 88/98 User Information xi

Table of Contents

LIST OF TABLES
Table 1-1 Front Controls, Indicators and Drive Bay Locations ............................................. 1-5
Table 1-2 Rear Connectors ................................................................................................... 1-7
Table 1-3 System Unit Components ..................................................................................... 1-9
Table 1-4 System Board Components................................................................................. 1-11
Table 1-5 Internal SCSI Cable Components ....................................................................... 1-13
Table 1-6 Internal Power Cable Components...................................................................... 1-15
Table 1-7 Key Groups and Functions.................................................................................. 1-17
Table 2-1 Recommendations for Posture and Work Habits ................................................. 2-35
Table 3-1 SCSI Address Recommendations.......................................................................... 3-7
Table 3-2 Communication Option Slot Locations ............................................................... 3-15
Table 3-3 Interface Standards and Cable Part Numbers ...................................................... 3-15
Table 4-1 System Troubleshooting ....................................................................................... 4-2
Table 4-1 System Troubleshooting (continued) .................................................................... 4-4
Table 4-2 Disk Drive Troubleshooting.................................................................................. 4-4
Table 4-3 Terminal Troubleshooting .................................................................................... 4-5
Table 5-1 Option Card Tests................................................................................................ 5–7
Table C-1 Alternative Boot Devices .................................................................................... C-1
Table C-2 Default Recovery Actions and Associated Values ............................................... C-2
Table E-1 System Specifications ..........................................................................................E-1
Table E-2 Acoustic Levels ...................................................................................................E-3
Table E-3 System Unit Metrics.............................................................................................E-3
Table E-4 System Operating and Nonoperating Conditions ..................................................E-3
Table E-5 AC Power Cords (Country Specific)....................................................................E-4
Table F-1 Devices and Priorities Normally Associated with SCSI IDs..................................F-2
Table G-1 Hardware Components........................................................................................ G-2
Table G-2 SCSI Addresses .................................................................................................. G-3
Table G-3 Hardware Configuration ..................................................................................... G-3
Table G-4 Installed Software............................................................................................... G-3

xii MicroVAX 3100 Models 88/98 User Information

Preface
Welcome to the MicroVAX 3100 Model 88 and Model 98
Systems
This book introduces the MicroVAX 3100 Model 88 and Model 98 Systems.
Use the information in this book to configure, start, use, update, and troubleshoot your
MicroVAX 3100 Model 88 and Model 98 Systems. You can also find general system
information such as console commands and system care in this book.

Audience
If you will be operating, configuring, or adding options to the MicroVAX 3100 Model 88
and Model 98 Systems, the information included in this book will be helpful to you.

Organization of the Information
This information for users covers the following topics:
•

Chapter 1, System Overview, describes the hardware components, including the Small
Computer Systems Interface (SCSI) architecture, the controller, the keyboard, the
system unit front panel, and the system unit rear panel.

•

Chapter 2, Getting Started, describes installing, starting, restarting, and turning off the
system.

•

Chapter 3, Installing Hardware Options, describes the system unit components and
gives instructions and illustrations to help you remove and replace them.

•

Chapter 4, Troubleshooting, describes system troubleshooting.

•

Chapter 5, Diagnostic Tests and Commands, describes system troubleshooting.

•

Appendix A, Console Commands, contains a basic description of the console
commands.

MicroVax 3100 Models 88/98 User Information xiii

Preface
•

Appendix B, Console Security, Provides information on setting the security password,
and logging in to the privileged console mode.

•

Appendix E, System Defaults, describes how to set/change the default boot device and
how to set/change the default recovery action.

•

Appendix D, System Care, describes how to clean your system, terminal, and
keyboard. It also contains instructions for moving and reinstalling your system.

•

Appendix E, Technical Specifications, describes the technical characteristics of the
system.

•

Appendix F, Setting SCSI IDs, describes how to select a unique SCSI ID for any SCSI
device installed in or attached to your system.

•

Appendix G, Equipment Log, contains tables that you can use to record information
about your system hardware and software components.

Refer to the Table of Contents for a detailed listing of topics.

Conventions
This guide uses the following conventions:
Convention Example
PARAMS>SHOW NODENAME>

Description
Monospaced, bold text indicates file names, path
names, directories, or screen text.

[Enter]

Square brackets surrounding text represent a key on
the keyboard.

[Ctrl]+[R]

A plus sign between keyboard keys indicates that
the keys shown should be pressed at the same time.

auto_action

Italic text indicates environment variables. Titles of
information sources are in italic, and occasionally
italic is used for emphasis in the text.

)

A pointing hand indicates a reference to additional
information.

xiv MicroVAX 3100 Models 88/98 User Information

Preface

Abbreviations
This guide uses the following abbreviations:

Abbreviation

Meaning

alternating current

amp

ampere

Celsius

compact disc

CD-ROM

compact disc read-only memory

CEE

International Commission for Conformity Certification of
Electrical Equipment

CFG

configuration file

centimeters

CPU

central processing unit

CSA

Canadian Standards Association

direct current

DMA

direct memory access

DRAM

dynamic random-access memory

FDI

Floppy Drive Interconnect

flashROM

electrically erasable, rewriteable, nonvolatile memory

feet

gigabyte

hertz

IEC

International Electrotechnical Commission

I/O

input/output

IRQ

interrupt request

ISO

International Organization for Standardization

kilobit

kilobyte

kilogram

pound

LED

light-emitting diode

meter

MicroVAX 3100 Models 88/98 User Information xv

Preface

Abbreviation

Meaning

MAU

media adapter unit

megabit

megabyte

MHz

megahertz.

millimeter

nanoseconds

NVRAM

nonvolatile random-access memory

ROM

read-only memory

SCSI

small computer system interface

SIMMs

single in-line memory modules

SROM

serial read-only memory

Underwriters Laboratories

VAR

value-added reseller

V AC

volts alternating current

VMS

Open VMS Operating System

watt

xvi MicroVAX 3100 Models 88/98 User Information

Preface

Special Notices
This guide uses three kinds of notices to emphasize specific information.
________________________WARNING __________________________
A WARNING indicates the presence of a hazard that can cause personal
injury.
____________________________________________________________
________________________ CAUTION ___________________________
A CAUTION indicates the presence of a hazard that can cause damage to
hardware or that might corrupt software.
____________________________________________________________
__________________________NOTE ____________________________
A NOTE gives general information, such as compatibility with other products or
pointers to other information.
____________________________________________________________

Additional Information Resources
You may wish to consult the following information resource for additional information
about your MicroVAX 3100 Model 88/98 System:
•

MicroVAX 3100 Models 88/98 Installation Information (order number EK-MV489-II),
which presents a graphical overview of the system installation.

Contact your distributor or Digital representative for other available product-related
information.

MicroVAX 3100 Models 88/98 User Information xvii

Preface

Reader’s Comments
Digital welcomes your comments on this or any other manual.

Digital Equipment Corporation
Shared Engineering Services
PKO3-2/21J
129 Parker Street
Maynard, MA 01754-2199

Please reference order number EK-MV489-UI. A01 in your correspondence.

xviii MicroVAX 3100 Models 88/98 User Information

1
System Overview
Introduction
Congratulations on your purchase of a MicroVAX 3100 Model 88/98 System. This
machine has been designed and tested with the utmost attention to performance and
reliability. Your system runs the OpenVMS operating system; its performance range can
be extended by the addition of memory and hard disk drives.
This chapter describes the MicroVAX 3100 Model 88/98 System’s hardware components,
including the Small Computer Systems Interface (SCSI) architecture, the keyboard, the
system unit front panel, and the system unit rear panel.
Following the information provided here will assure safe and proper operation of your
MicroVAX 3100 Model 88/98 System.

MicroVax 3100 Models 88/98 User Information 1-1

System Overview

System Unit
Your MicroVAX 3100 Model 88/98 System uses a mini-tower desktop enclosure.
The system unit includes:
•

CPU module/motherboard with built-in SCSI, NI Bus and port, Console port, and 2
serial ports, as well as:

•

Model 88
16 ns NVAX CPU chip
128 KB of on-board cache memory

•

From 64 MB to 512 MB of memory, consisting of single in-line memory modules
(SIMMs)

•

Six accessible/non-accessible drive bays

Model 98
10 ns NVAX CPU chip
512 KB of on-board cache memory

a) One with a standard 5.25-inch CD-ROM drive
b) One with a standard 3.5-inch RZ26 SCSI disk
c) Two more slots for optional 3.5 or 5.25-inch hard disk or removable-media drives
d) Two non-accessible I/O bays (for optional 3.5 inch hard disk drives only).

1-2 MicroVAX 3100 Models 88/98 User Information

System Overview
•

Two SCSI ports; one standard and one optional

•

Synchronous and asynchronous communication adapters (optional).

•

ThinWire and ThickWire Ethernet

•

3-year, on-site warranty

•

OpenVMS 5.5-2XX

)

Refer to Appendix E, Technical Specifications, for additional information.

MicroVAX 3100 Models 88/98 User Information 1-3

System Overview

Enclosure Front Panel
Figure 1-1 shows a front view of the system enclosure with pointers to the controls and
indicators (storage bay door opened for clarity). Table 1-1 describes these items.
2

6
1

7
8

9
10
11
12

MLO-013510

Figure 1-1 Front Controls, Indicators and Drive Bay Locations

1-4 MicroVAX 3100 Models 88/98 User Information

System Overview

Table 1-1 Front Controls, Indicators and Drive Bay Locations
Figure
Legend

Component

Front door

Power switch

Disk drive LED

Power LED

Halt switch: halts the system and returns it from the operating
system to the console mode.

RZ 2x SCSI disk (non-accessible)

Accessible/Nonaccessible bay for 3.5-inch or 5.25-inch

CD-ROM volume switch

CD-ROM headphone jack

CD-ROM activity light

CD-ROM eject button

MicroVAX 3100 Models 88/98 User Information 1-5

System Overview

Enclosure Rear Panel
Table 1-2 show the controls and connectors. Table 1-2 lists the rear controls and
connectors and describes their functions.
7
8
9
1

5
14
15
16
17
6

18
19
MLO-013511

Figure 1-2 Rear Connectors (Rear View)

1-6 MicroVAX 3100 Models 88/98 User Information

System Overview
Table 1-2 Rear Connectors
Figure
Legend

Component

SCSI Port (terminator required)

2A AC Power Outlet Connection

AC Power Input Connector

Pre-installed Software Label

System Identification Label

Lockdown Hasp

ThinWire Ethernet

ThinWire Ethernet LED

ThickWire Ethernet

ThickWire Ethernet LED

Modem Port (with adapter)

MMJ Port (for Console only)

MMJ Port

Asynchronous Communication (optional)

Synchronous Communication (optional)

Reserved

KZDDA SCSI Port (optional)

MicroVAX 3100 Models 88/98 User Information 1-7

System Overview

System Components
Figure 1-3 shows the location of the MicroVAX 3100 Model 88 and Model 98 Systems
components. Table 1-3 lists the system components.

4
1

MLO-013606

Figure 1-3 System Unit Components

1-8 MicroVAX 3100 Models 88/98 User Information

System Overview

Table 1-3 System Unit Components
Figure
Legend

Component

Front Door

CD-ROM

System Disk Drive

System Board

SIMM Board (required)

SIMM Board (optional)

Power Supply

Rear Drive Bay

DHW42 Asynchronous Option

DSW43 Synchronous Option

SCSI (2nd) Optional

CDAL I/O Board

MicroVAX 3100 Models 88/98 User Information 1-9

System Overview

System Board
Figure 1-4 shows the location of the MicroVAX 3100 Model 88 and Model 98 system
board components. Table 1-4 describes these components. If it is necessary to access
components on the system board, refer to Chapter 3, Figure 3-14 for system board removal
and Figure 3-15 for removing the plastic system board cover.

10
11
12
13
16

14
MLO-013516

Figure 1-4 System Board Components

1-10 MicroVAX 3100 Models 88/98 User Information

System Overview
Table 1-4 System Board Components
Figure
Legend

Components

CPU Fan Connector (J25)

MEM1 Carrier Connector (J4)

MEM2 Carrier Connector (J1)

Diagnostic Display LEDs (D26, D29); indicate system and test status
for Digital Services engineers using the on-line Service Guide.

Diagnostic Display LEDs (D31)

Break/Enable Switch (See

Thick/ThinWire Ethernet Jumper (J27) ThinWire Default

ThinWire Ethernet Connection (J24)

ThickWire Ethernet Connection (J21)

Modem Connector (J11)

Console Port MMJ (J9)

Console Port MMJ (J8)

Console Port MMJ (J2)

NVAX CPU (E36)

19.2/38.4 K baud Jumper (W13) 19.2k baud default

19.8 K baud Jumper (J26) Default Installed

below)

Break/Enable Switch Positions
a)

When the switch is in the up position, the LED is on and you can halt the
system by pressing the break key on the console terminal keyboard.

b) When the switch is in the down position, the LED is off and you can not halt
the system by pressing the break key on the console terminal keyboard.

MicroVAX 3100 Models 88/98 User Information 1-11

System Overview

Internal Signal Cable Routing
Figure 1-5 shows the routing of the SCSI cable in MicroVAX 3100 Models 88/98 systems.
Table 1-5 lists the components.

6
5

3
2

MLO-013704

Figure 1-5 Internal SCSI Cable Routing

1-12 MicroVAX 3100 Models 88/98 User Information

System Overview

Table 1-5 Internal SCSI Cable Components
Figure
Legend

Components

CDAL I/O

Optional Hard Drive

CD-ROM

Optional Storage Device

Hard Drive

Terminated SCSI Port

MicroVAX 3100 Models 88/98 User Information 1-13

System Overview

Internal Power Cable Routing
Figure 1-6 shows the routing of the internal power cable in MicroVAX 3100 Models 88/98
systems. Table 1-6 lists the components.

7
6

2
3

4
MLO-013703

Figure 1-6 Internal Power Cable Routing

1-14 MicroVAX 3100 Models 88/98 User Information

System Overview

Table 1-6 Internal Power Cable Components
Figure
Legend

Components

Power Supply

Optional Hard Drive

CDAL I/O

CD-ROM

Optional Storage Device

Hard Drive

MicroVAX 3100 Models 88/98 User Information 1-15

System Overview

The Keyboard
Your system comes equipped with a 101-key enhanced keyboard (ordered separately and
shown in Figure 1-7) that allows you to communicate with your system by entering data or
commands. Note that some European keyboards have 108 keys. Refer to Table 1-7 for
information on keyboard key groups and functions.

)

Refer to your operating system or application software documentation for softwarespecific key functions.
_________________________ NOTE____________________________
You can adjust the angle of the keyboard for your comfort. The underside of the
keyboard has feet that swing down and lock into place.
___________________________________________________________

Figure 1-7 Typical Keyboard Layout

1-16 MicroVAX 3100 Models 88/98 User Information

System Overview
Table 1-7 Key Groups and Functions
Figure
Legend

Key, Key Group

Function

[Escape] key

This key is program-specific. Its function is
determined by the installed application
software.

Function key group

These keys are program-specific. Their
functions are determined by the installed
application software.

Edit key group

These keys are program-specific. Their
functions are determined by the installed
application software.

Indicator lights

These lights indicate whether [NumLock],
[CapsLock], or [ScrollLock] has been
activated.

Numeric keypad

These keys perform numeric functions and
software-defined functions, including cursor
control. The [NumLock] key allows you to
toggle between the numeric functions and
software-defined functions.

Cursor control key group

These keys control the movement of the
highlighted cursor on the terminal screen.

Alphanumeric key group

These typewriter-specific keys feature
automatic-repeat capability. If you press and
hold down any of these keys, the keystroke
repeats automatically until released.

MicroVAX 3100 Models 88/98 User Information 1-17

2
Getting Started
Introduction
This chapter describes how to install, start, restart, and turn off your MicroVAX 3100
Model 88 and Model 98 Systems. You can also find information here about preloaded
software as well as guidelines for system security. Figure 2-1 shows a typical MicroVAX
3100 Model 88 and Model 98 System in its tower configuration.

________________________WARNING __________________________
When unpacking and moving system components, be aware that some
components (such as the system unit or terminal) may be too heavy for you
to safely lift alone. If you are doubtful about whether you can lift these items
alone, please get assistance.
____________________________________________________________

MicroVax 3100 Models 88/98 User Information 2-1

Getting Started

ML013512

Figure 2-1 MicroVAX 3100 Model 88/98 System

Before Starting Your System
Before you start your system MicroVAX 3100 Model 88 and Model 98 System, follow this
procedure:
1.

Read and understand the information supplied with your system.

Select a well-ventilated site near a grounded power outlet and away from sources of
excessive heat. Also, use an appropriate power strip to isolate the site from electric
noise (for example, spikes, sags, and surges) produced by devices such as air
conditioners, large fans, radios, and televisions.

Save all shipping containers and packing material for repackaging or moving the
system later.
_________________________ NOTES ___________________________
•

Do not install optional hardware or application software until you have
started your system and verified that the base system is working correctly.

•

On systems that have preloaded software, a label attached to the system unit
informs you that there is licensed software installed. Carefully review the
software license agreement shipped with your system.
___________________________________________________________

2-2 MicroVAX 3100 Models 88/98 User Information

Getting Started

Converting the System to Lie Flat on the Desktop
Your MicroVAX 3100 Model 88 or Model 98 system is shipped in the tower configuration
as shown in Figure 2-1. The system can also be used in a desktop configuration as shown
in Figure 2-2.

MLO-013649

Figure 2-2 Desktop Configuration
_________________________ Caution ___________________________
If you will be using the system in the horizontal desktop position as shown, you
must use clips that will prevent the CD-ROM media from falling out of the tray
when ejected. Please refer to the User Guide that is supplied with the CD drive
for instructions on using the clips.
____________________________________________________________

MicroVAX 3100 Models 88/98 User Information 2-3

Getting Started
If you wish to use your MicroVAX 3100 Model 88/98 system in its desktop configuration,
you must first remove the front door.
1.

With the door open, push on each hinge, as shown, to disengage them. Lift the door
away. See Figure 2-3.

MLO-013607

Figure 2-3 Removing the Front Door
2.

Set the system down with the power button on the bottom left as shown in Figure 2-2.

Place the front door in a secure location. You may wish to use the system in its tower
configuration at some other time.

Locking Your System
Your MicroVAX 3100 Model 88 or Model 98 system may be locked and/or secured to a
desk or table using a lockdown hasp. Follow these instructions and see Figure 2-4 to
expose and install the hasp.

2-4 MicroVAX 3100 Models 88/98 User Information

Getting Started
_________________________ Caution ___________________________
a.

To avoid damage from static discharge, touch bare (unpainted) metal on the
system box before you touch anything inside the system.
b. To avoid damage from overheating, system covers must be in place when
running the system for extended periods of time.
____________________________________________________________
1.
2.

Make sure the system is turned off and unplugged.
Facing the rear of the unit, locate and loosen the three thumbscrews  that fasten the
top cover to the enclosure. Pull back on the cover (two or three inches), and lift the
cover up and away from the enclosure.

MLO-013628

Figure 2-4 Removing the Cover

MicroVAX 3100 Models 88/98 User Information 2-5

Getting Started
3.

Insert the end of the hasp with the hole in it through the slot on the rear of the
enclosure.

Place the other end of the hasp securely behind the slot on the rear panel.

You may use a lock through the hasp, or use a chain or cable lock through the hasp to
secure the system to a table. Refer to Figure 2-5.

ML013514

Figure 2-5 Installing the Hasp

Identifying the Correct AC Power Cord
Your MicroVAX 3100 Model 88 and Model 98 System comes equipped the proper AC
power cord. However, because variations exist from one country to another, MicroVAX
3100 Model 88 and Model 98 and systems may be moved, inspect your power cord to
ensure that it is the correct one for your country or region. If you are not sure that the
supplied AC power cord is correct, contact your authorized Digital service representative
or distributor before you use it. Refer to Appendix E, Table E-5, for list of cables.

2-6 MicroVAX 3100 Models 88/98 User Information

Getting Started
________________________WARNING __________________________
Do not attempt to modify or use an external 115V AC power cord for 230V
AC input power. Modifying the power cord can cause personal injury and
severe equipment damage.
____________________________________________________________
Power cords supplied with the MicroVAX 3100 Model 88 and Model 98 System meet the
following criteria:
•

The cords set for North America are UL-listed/CSA-certified, and rated 120VAC, 10A
minimum.

•

In Europe, the cordage carries the <HAR> mark. See Table E-5, Appendix E for
ratings.

•

The cordage is terminated in a grounding-type plug and must have approvals showing
it is suitable for use within the region.

•

The connector at the equipment end must be an IEC3201-type CEE2 style 14
connector.

•

The cord length does not exceed 4.5 m (14.5 ft).

Installing Your System
The MicroVAX 3100 Model 88 and Model 98 System Installation Information you received
with your system graphically outlines the steps to follow to install your system.
1.

Make sure you received all of your system components. Use Appendix G, Equipment
Log, to list your equipment. If something is missing, please contact your distributor or
Digital representative.

Position your system so that air can flow freely to and from the vents. Figure 2-6
shows the airflow from the front and rear of the system.

1 International Electrotechnical Commission.
2 International Commission for Conformity Certification of Electrical Equipment.

MicroVAX 3100 Models 88/98 User Information 2-7

Getting Started

MLO-013695

Figure 2-6 System Enclosure Airflow
_______________________ CAUTIONS _________________________
To ensure that your system is properly cooled:
•

Make sure that air can freely flow into the front, and out of the rear of the
system unit.
• Do not remove a filler plate until you are ready to add a new system
component.
___________________________________________________________

2-8 MicroVAX 3100 Models 88/98 User Information

Getting Started
Connecting System Components
To connect the components of your MicroVAX 3100 Model 88 and Model 98 System,
follow this procedure:

Connecting the Console Terminal
To connect the console terminal, refer to Figure 2-7 and follow these steps:
1.

Connect one end of the terminal cable to the modified modular jack (MMJ) port on
the rear of the system.

Connect the other end of the cable to the MMJ port on the console terminal itself.

Connect the terminal power cord to the terminal and an isolated, grounded circuit.
See the terminal documentation for more information.

MLO-013616

Figure 2-7 Connecting the Console Terminal

MicroVAX 3100 Models 88/98 User Information 2-9

Getting Started
_________________________ NOTE____________________________
When the system is shipped, MMJ ports 0 and 1 are covered with an arrow
label identifying port 3 as the console port. When port 3 has been identified,
the OPA0 arrow label may be removed.
___________________________________________________________

Network Connection and Termination
Your MicroVAX 3100 Model 88/98 System can be connected to either a ThinWire
Ethernet or a ThickWire Ethernet network. A jumper on the system board determines
whether you are using ThinWire or ThickWire Ethernet.
If you do not use an Ethernet network, you should install the ThinWire and ThickWire
terminators on the back of your system as shown in Figure 2-12 and Figure 2-19
respectively.
If you will be using either ThinWire or ThickWire Ethernet, follow these general steps,
which are detailed in the following sections.
1.

Select ThinWire or ThickWire by installing the jumper on the system board.

Assemble/connect the network to the appropriate port.

Test the network connection.

Notify the network coordinator to complete the installation.

Selecting ThinWire or ThickWire Ethernet
Select either ThinWire Ethernet or ThickWire Ethernet by installing the selector jumper
on the system board module. Install the jumper in the setting  position for ThinWire
Ethernet, and in the setting  position for ThickWire Ethernet (See Figure 2-8).

2-10 MicroVAX 3100 Models 88/98 User Information

Getting Started

MLO-013614

Figure 2-8 Selecting the ThinWire or ThickWire Ethernet

MicroVAX 3100 Models 88/98 User Information 2-11

Getting Started
Connecting ThinWire Ethernet
If you are using ThinWire Ethernet, follow these steps:
1.

Assemble the terminator, extender, t-connector and ThinWire Ethernet Cable
connector as shown in Figure 2-9.

MLO-013701

Figure 2-9 Assembling the ThinWire Ethernet Connector

Connect the assembly to the ThinWire Ethernet port on the rear of the system.

Install the ThickWire Ethernet terminator. Refer to Figure 2-10.

2-12 MicroVAX 3100 Models 88/98 User Information

Getting Started

MLO-013615

Figure 2-10 Installing the ThinWire Ethernet

MicroVAX 3100 Models 88/98 User Information 2-13

Getting Started
Connecting ThickWire Ethernet
If you are using ThickWire Ethernet, connect it as follows:
1.

If you are using ThickWire Ethernet, configure the jumper as in Figure 2-8.

Attach the 15-pin connector on the ThickWire Ethernet transceiver cable to the
ThickWire Ethernet port on the rear of the system by sliding the clip upward.

Install the ThinWire Ethernet terminator as shown in Figure 2-11.

MLO-013616

Figure 2-11 Installing ThickWire Ethernet

2-14 MicroVAX 3100 Models 88/98 User Information

Getting Started
Connecting a SCSI Cable or the SCSI Terminator
To connect the SCSI terminator, follow these steps:
1.

If you have an external small computer system interface (SCSI) interface or SCSI
storage box, connect the SCSI cable to the SCSI port on the rear of the system,
otherwise install the SCSI terminator (supplied with your system). Figure 2-12 shows
an example of the SCSI terminator connection. See the section on SCSI Termination
in Chapter 3 for additional information.

MLO-013623

Figure 2-12 Connecting the SCSI Terminator

MicroVAX 3100 Models 88/98 User Information 2-15

Getting Started

Connecting External Options to the System
The following subsections contain information on these tasks:
•

Connecting peripherals to a DEC423 MMJ port

•

Connecting a peripheral to the asynchronous modem control port (port2)

•

Connecting peripherals to an optional asynchronous port

•

Connecting peripherals to an optional synchronous port

Connecting Peripherals to a DEC423 MMJ Port
To connect peripherals that use DEC423 cables (BC16E) to MMJ ports 0, 1,
or 3, refer to Figure 2-13 follow these steps:
1.

Set the on/off switch on the peripheral to the off (O) position.

Verify the MicroVAX is Off and Power Cord is removed.

Connect one end of the DEC423 cable to either MMJ port 0, 1, or 3

Connect the other end of the DEC423 cable to the correct port on the peripheral.

Set the on/off switch on the peripheral to the on position.

BC16E cables are available in the following lengths:
10 feet (BC16E-10), 25 feet (BC16E-25), or 50 feet (BC16E-50).

2-16 MicroVAX 3100 Models 88/98 User Information

Getting Started

MLO-013617

Figure 2-13 Connecting Peripherals to a DEC423 MMJ Port
Connecting a Peripheral to the Asynchronous Modem Control Port
You can connect peripherals that use EIA-232 connectors to the asynchronous modem
control port on the back of the system unit. Alternatively, the supplied EIA-232 to
DEC423 adapter (H8575-A) allows you to connect peripherals that use DEC423
connectors. This port may be used as a terminal port as well as a modem port.
If you are connecting a peripheral to the asynchronous modem control port using EIA-232
cables, refer to Figure 2-14 and follow these steps:
a)

Set the ON/OFF switch on the peripheral to the OFF (O) position.

b) Connect the 25-pin D-sub connector of the peripheral cable to the asynchronous
modem control port.
c)

If the connector has screws on either side, tighten them using a small screwdriver.

d) Connect the other end of the peripheral cable to the correct port on the peripheral.
e)

Set the ON/OFF switch on the peripheral to the ON position.

MicroVAX 3100 Models 88/98 User Information 2-17

Getting Started
EIA-232 cables are available in the following lengths: 10 feet (BC22F-10), 25 feet
(BC22F-25), or 50 feet (BC22F-50). The peripheral you are using may require a nullmodem extension cable. See the peripheral documentation or contact your Digital sales
representative for information on the correct null-modem cable to use.
________________________ Caution ___________________________
This modem control port has default support for non-standard 19.8 Kbaud. To
change to 19.2 Kbaud, user must remove Jumper on J26 on the CPU mother
board. Refer to Chapter 3, Figure 3-14.
___________________________________________________________

MLO-013618

Figure 2-14 Connecting an EIA Connector to the Asynchronous Port

2-18 MicroVAX 3100 Models 88/98 User Information

Getting Started

If you are connecting a peripheral using DEC423 cables, refer to Figure 2-15 and follow
these steps: Set the ON/OFF switch on the peripheral to the OFF (O) position.
a)

Connect the EIA-232 to DEC423 adapter to the asynchronous modem control port.

b) Tighten the screws on each side of the adapter using a small screwdriver.
c)

Connect the DEC423 cable to the MMJ port on the adapter.

d) Connect the other end of the DEC423 cable to the correct port on the peripheral.
e)

Set the ON/OFF switch on the peripheral to the ON (l) position.

MLO-013619

Figure 2-15 Connecting a DEC423 Connector to the Asynchronous Port

MicroVAX 3100 Models 88/98 User Information 2-19

Getting Started
Connecting Peripherals to an Optional Asynchronous Port
There are two asynchronous communications options for Micro VAX 3100 88/98 systems:
•

DHW42-BB -- Provides two eight-line data-line-only asynchronous ports

•

DHW42-CB -- Provides two four-line asynchronous ports with modem control

If the system has the DHW42-BB asynchronous communications option installed, the
system has one or two eight-line data-only asynchronous ports. You can connect up to
eight peripherals to each of these ports using the H3104 harmonica.
To connect a peripheral to a DHW42-BB asynchronous port using the H3104 harmonica,
refer to Figure 2-16 and follow these steps:
1.

Set the ON/OFF switch on the peripheral to the OFF (O) position.

Make sure that the 120-pin-to-2 x 36-pin cable supplied with your DHW42-BB is
installed. (Figure 2-16, Item 1)

Connect the straight connector of the BC16C-10 cable to one of the asynchronous
cable ports on the back of the system unit. (Figure 2-16, Item 2)

Close the bail lock loops on each side of the connector.

Connect the angled connector of the BC16C-10 cable to the H3104 harmonica.

Close the bail lock loops on each side of the connector.

Connect one end of a DEC423 cable to one of the eight MMJ ports on the harmonica.

Connect the other end of the DEC423 cable to a DEC423 port on the peripheral.

Set the ON/OFF switch on the peripheral to the ON (l) position.

2-20 MicroVAX 3100 Models 88/98 User Information

Getting Started

2
MLO-013620

Figure 2-16 Connect a DHW42-BB Asynchronous Port

MicroVAX 3100 Models 88/98 User Information 2-21

Getting Started
Connecting Peripherals to a DHW42-CB Option
If the system has the DHW42-CB asynchronous communications option installed, the
system has two four-line asynchronous ports with modem control. You can connect up to
four peripherals to each of these ports using the breakout cable (BC29J-06) supplied with
the option.
To connect a peripheral to an asynchronous port, refer to Figure 2-17 and follow these
steps:
1.

Set the ON/OFF switch on the peripheral to the OFF (O) position.

Make sure that the 120 pin to 2 x 50 pin cable supplied with the DHW42-CB is
installed. (Figure 2-17, Item 1)

Hold in the connector clips on either side of the 50-pin connector of the breakout
cable and connect it to one of the asynchronous cable ports on the back of the system
unit. (Figure 2-17, Item 2)

Release the clips. The hooks on the port secure the connector in place.

Connect one of the four EIA-232 connectors on the breakout cable to the peripheral.

Set the ON/OFF switch on the peripheral to the ON (l) position.

2-22 MicroVAX 3100 Models 88/98 User Information

Getting Started

MLO-013621

Figure 2-17 Connecting to a DHW42-CB Asynchronous Port

MicroVAX 3100 Models 88/98 User Information 2-23

Getting Started

Connecting Peripherals to an Optional Synchronous Port
If the system has the DSW43-AA synchronous communications option installed, the
system has two synchronous modem ports. The EIA-232/V.24 cable (BC19D-02) is the
standard cable shipped with the option. If you are using a synchronous interface standard
other than EIA-232/V.24, use one of the optional cables listed in Table 3-3.
To connect a peripheral to a synchronous port, refer to Figure 2-18 and follow these steps:
1.

Set the ON/OFF switch on the peripheral to the OFF (O) position.

Connect the 100-pin-to-2x50-pin cable, supplied with your DSW43-AA. (See Figure
2-18, Item 1).

Connect the 50-pin connector of the option cable to one of the synchronous cable
ports on the back of the system unit. (See Figure 2-18, Item 2).

Connect the other connector of the option cable to the communications port on the
peripheral.

If the option cable connectors are fitted with screws, secure the connectors to the ports
by tightening them on each side.

Set the ON/OFF switch on the peripheral to the ON (l) position.

2-24 MicroVAX 3100 Models 88/98 User Information

Getting Started

MLO-013622

Figure 2-18 Connecting to a DSW43-AA Synchronous Port

MicroVAX 3100 Models 88/98 User Information 2-25

Getting Started

Installing a SCSI Terminator on an Optional KZDDA
If you are installing a SCSI terminator, refer to Figure 2-19 below.

MLO-013702

Figure 2-19 Installing a SCSI Terminator on an Optional KZDDA

2-26 MicroVAX 3100 Models 88/98 User Information

Getting Started

Connecting the Power Cord
_________________________ Caution ___________________________
Your system uses a momentary switch for On/Off control. Always assume that
your system will come on when the AC power cord is installed.
____________________________________________________________
To connect the power cord, refer to Figure 2-20 and follow these steps:
1.

Connect the power cord to the rear of the system.

Connect the other end of the power cord to an isolated, grounded circuit.

MLO-013702

Figure 2-20 Connecting the Power Cord

MicroVAX 3100 Models 88/98 User Information 2-27

Getting Started
Starting Your System
To turn on the system, refer to Figure 2-21 and follow these steps:
1.

Verify your system is OFF by the Power LED indicator.

Turn on the console terminal. Wait until it completes its power-up self test. See the
terminal documentation for more information.

Connect the other end of the power cord to an isolated, grounded circuit.

Turn on the system unit by momentarily pushing in the On/Off switch until the Power
LED is illuminated.

MLO-013608

Figure 2-21 Turning the System On

2-28 MicroVAX 3100 Models 88/98 User Information

Getting Started
Checking the Power-Up Test Results
The power-up test can take several minutes to complete, depending on the number of
installed options you have and on which default settings you use:
A. If the power-up test results on the screen are similar to the results shown below, the
system has passed the power-up test.
B. If the power-up test results on the screen are not similar to the results shown below,
the system has not passed the power-up test. Go to sub-step 1.

KA58-A or KA59-A

V1.0, VMB 2.16

Performing normal system tests.
74..73..72..71..70..69..68..67..66..65..64..63..62..61..60..59..
58..57..56..55..54..53..52..51..50..49..48..47..46..45..44..43..
42..41..40..39..38..37..36..35..34..33..32..31..30..29..28..27..
26..25..24..23..22..21..20..19..18..17..16..15..14..13..12..11..
10..09..08..07..06..05..04..03..
Tests completed.
>>>

Central Processing Unit (CPU) name, Firmware version number, and Virtual Memory
Boot (VMB) version number

Read-Only Memory (ROM) based diagnostics countdown
 Status message
 Console prompt
1.

Write down the error messages and the error summaries. the following example shows
an error message and an error summary.

Turn the system OFF and remove AC power cord..

Make sure that all the connections you made in step 3, step 4, step 5, and step 6 are
correct.

Attach the AC power cord and turn the system ON.

If an error report is still displayed, see the Troubleshooting chapter in this manual.

MicroVAX 3100 Models 88/98 User Information 2-29

Getting Started
KA58-A or KA59-A

V1.0, VMB 2.16

Performing normal system tests.
74..73..72..71..70..69..68..67..66..65..64..63..62..61..60..59..
DE_Memory_Setup_CSRs.lis

? Test_Subtest_31_05 Loop_Subtest=00 Err_Type=FF
Vec=0000 Prev_Errs=0000
P4=00010000

P1=00000000

P2=01000000

P3=00000001

P5=2101801C P6=00000007 P7=80000003 P8=0000CF4A

P9=00000001 P10=2006B8D8

r0=00000002 r1=21018000 r2=00000008 r3=81000000

r4=00000001

r5=01000000

r6=2006EB77 r7=21018048 r8=00000000 r9=20140758 r10=00000000 r11=FFFFFFFF
dser=0000 cesr=00000000 intmsk=00 icsr=01 pcsts=FA00 pcadr=FFFFFFF8
pcctl=FC13
cctl=00000020 bcetsts=0360 bcedsts=0F00 cefsts=00019200 nests=00
mmcdsr=01FE6600 mesr=00000000
58..57..56..55..54..53..52..51..50..49..48..47..46..45..44..43.. 
42..41..40..39..38..37..36..35..34..33..32..31..30..29..28..27..
26..25..24..23..22..21..20..19..18..17..16..15..14..13..12..11..
10..09..08..07..06..05..04..03..

Memory Set 0: 00000000 to 00FFFFFF, 16MB, 32768 good pages, 0 bad pages

Set 0 on SIMM_carrier_J4

(J5...)

(J6...)

(7...)

(J8??)

Total of 16MB, 32768 good pages, 0 bad pages, 104 reserved pages
Normal operation not possible.

Error message
 Error summary
 Power-up test completion
 Specific error information on the test that failed
 Status message

2-30 MicroVAX 3100 Models 88/98 User Information

Getting Started
Testing the Ethernet Installation
When you complete the network installation procedure, follow
these steps to test the installation:
1.

Attach your power cord and turn the system ON.

Enter the following command to test the installation:

>>>T 5F
>>>
3.

Run test 5F with the first parameter set to 0 (default) to test
the SGEC chip using internal loopback mode. An example of
success is shown by the console prompt returning without any
messages as shown in the next two examples.

>>>T 5F
>>>
4.

Another example of test success is shown with test 5F first
parameter set to 1 to test the SGEC chip using external
loopback mode. This requires a terminator on the selected
Ethernet port, either thin wire or thick wire. If the test is run
while connected to an active net, it may fail.

>>>T 5F
>>>
5.

If the device fails the self-test, the system responds with a
display similar to the following:

>>>T 5F
? Test_Subtest_5F_18
Vec=010C

Loop_Subtest=0E

Prev_Errs=0000

Err_Type=FF

DE_SGEC.lis

P1=00000001

P2=00000000

P3=827DFF03

P4=00000000

P5=00000000

P6=00000000

P7=00000000

P8=00000001

P9=00000000 P10=00000000

r0=00000054

r1=000082E2

r2=00000001

r3=000082FA

r4=00008230

r6=000082E2

r7=20008000

r8=00008000

r9=20140758

r10=13000001 r11=2014044B

r5=00000040

EPC=2005721A dser=0000 cesr=00000000 icsr=01 pcsts=F800 pcctl=FC13
cctl=00000007 bcetsts=03A0 bcedsts=0400 cefsts=00019200 nests=00
mmcdsr=00C6C600 mesr=00006000

>>>

MicroVAX 3100 Models 88/98 User Information 2-31

Getting Started
6.

If the device fails, see Chapters 5, Troubleshooting, and 6,
Diagnostic Tests and Commands.

Completing the Ethernet Installation
The network coordinator must complete the installation. You must
give the following information to the network coordinator:
•

A unique node name comprised of a maximum of six
alphanumeric characters.
Choose a node name and ask the network coordinator to make
sure that the node name is unique on the network.

•

The system's Ethernet address

To determine the system's Ethernet address, follow these steps:
1.

Enter the following command at the console prompt:
>>>SHOW ETHERNET
The system displays a response similar to the following:

ETHERNET = 08-00-2B-1A-0B-BB
The alphanumeric string, shown in the form nn-nn-nn-nn-nn-nn, is
the Ethernet address.
2.

Write down the Ethernet address and give it to the network
coordinator.

If the Network Installation Fails
If the network installation fails, contact your Digital services
representative.
Removing the System Unit from a Network
The following subsections describe how to remove the system unit
from a network.

2-32 MicroVAX 3100 Models 88/98 User Information

Getting Started
__________________________ Note _____________________________
Before removing the system unit from a network:
• Get the approval of the network coordinator.
• See the operating system documentation for
information on the shutdown procedures before
stopping or turning off the system.
• If the system is the server in a network, do not turn off,
halt or restart the system without notifying the other
network members.
____________________________________________________________
Removing the System Unit from a ThinWire Ethernet Cable
To remove the system unit from a ThinWire Ethernet cable,
follow these steps:
1.

Power the system off.
_________________________ Caution ___________________________
Disconnecting the ThinWire Ethernet terminator or the
ThinWire Ethernet cable connectors from the T-connector
may cause disruptions to network communications.
____________________________________________________________

Disconnect the entire T-connector from the system (see
Figure 2-10 and add a terminator to the ThinWire port on the
back of the system unit (seeFigure 2-11).

Removing the System Unit from a ThickWire Ethernet Cable
To remove the system unit from a ThickWire Ethernet cable,
follow these steps:
1.

Power the system off.

Disconnect the transceiver cable from the ThickWire
Ethernet connector on the back of the system unit (see Figure
2-11 and replace it with a terminator (see Figure 2-10).

MicroVAX 3100 Models 88/98 User Information 2-33

Getting Started
Booting the Operating System
The system is supplied with factory installed software (FIS) on the system disk. Boot the
operating system following the procedures in the OpenVMS Factory Installed Software
User Guide.
Turning Off Your System
Before turning off your system, make sure to save and close all open files. If you turn the
system off without saving and closing files, you could corrupt some or all of your data.
To turn off your system, follow this procedure:
1.

Close any application data files you have open as well as any applications you have
running. Most application programs prompt you to save the information before
closing.

Shut down the operating system by typing the following from a privileged account:
@sys$system:shutdown

Wait for the operating system to complete the shutdown process and you are prompted
to use the halt button to get to the console prompt (>>>).

Do not turn off power to your system and peripherals until the shutdown sequence
completes, and you are at the console prompt (>>>).

Computer Security
When the security password is set, there are two types of users: privileged users and
unprivileged users. Privileged users know the security password and can use the full range
of console commands; unprivileged users can only use the following commands:
•

•

BOOT-- Use this command without parameters to boot the operating system when the
boot device has been set.

See Appendix B for more information on console security and setting the password.

Posture and Work Habits
If you use poor posture while you work or if your equipment is poorly positioned, personal
injury may result (as suggested by certain recent scientific articles). Although other articles
suggest that there is no cause and effect, we strongly recommend that you read and follow
the precautions outlined in Figure 2-22 and Table 2-1. In addition, be sure to adjust your
work area so that you are comfortable.

2-34 MicroVAX 3100 Models 88/98 User Information

Getting Started

Figure 2-22 Recommendations for Posture and Work Habits
Table 2-1 Recommendations for Posture and Work Habits
Adjust

Figure
Callout

To allow the following conditions:

Chair

Your feet are flat on the floor.

Your legs are vertical and form a right angle to the floor.

Your thighs are horizontal, and they are not bearing weight. To
prevent restriction of the blood flow, keep the backs of your
knees away from the seat so you do not compress the area
behind them.

Your upper body is erect and your lower back is supported with
a backrest.

MicroVAX 3100 Models 88/98 User Information 2-35

Getting Started
Adjust

Figure
Callout

Keyboard

To allow the following conditions:
Your wrists are straight and do not flex more than 15 degrees.
They are supported and do not rest on sharp edges. If you use a
mouse, rest your hand on the mouse so your wrist is not on the
work surface.
Your upper arms are straight down at your sides, and your
elbows are close to your sides and support your arm weight.
Forearms are at a 70- to 90-degree angle.

Head

Avoid neck strain. Your head should incline downward, but no
more than 15 to 20 degrees.

Terminal

The terminal should be no higher than the level of your eyes and
at the correct distance for your vision.

Avoid eye fatigue, which can be caused by glare, image quality,
uncomfortable furniture, eye height, and uncorrected vision. If
you cannot focus to read at different distances, you may need
special glasses. Relax your eyes periodically by focusing on
distant objects.

Lighting

Direct lighting or sunlight on the screen causes glare and
reflections. Place lighting behind or to the side of your work
area, and distribute the lighting evenly on your work area.

2-36 MicroVAX 3100 Models 88/98 User Information

Getting Started

Table 2-1. Recommendations for Posture and Work Habits (continued)
Adjust

Figure
Callout

To allow for the following conditions:

Noise

Keep background noise at a minimum. Background noise above
65 dBa is tiring. Sound-absorbing materials (for example,
curtains, carpeting, and acoustic tile) can help reduce
background noise.

Temperature

The temperature should be between 20° and 23°C (68° and 74°
F).

Humidity

The humidity should be between 30% and 70%.

Ventilation

Provide adequate air ventilation to operate the equipment and
avoid fatigue.

Work Area

Your work area should be greater than 70 cm (28 inches) center
to center, preferably 152 cm (60 inches).

________________________WARNING __________________________
If you experience pain or discomfort while using your system, rest and
review the instructions for posture and work habits. If the pain or
discomfort continues after resuming work, discontinue use and report the
condition to your job supervisor or physician.
____________________________________________________________

MicroVAX 3100 Models 88/98 User Information 2-37

3
Installing Hardware Options
Introduction
This chapter covers the following topics related to installing system options on the Digital
MicroVAX 3100 Model 88 and Model 98 Systems:
•

Opening and closing the system cover

•

Installing additional system memory

•

Installing internal drives

•

Installing I/O communications options

•

Connecting external devices

•

Cable layout for power, and SCSI
________________________ CAUTION ___________________________
a.

MicroVax 3100 Models 88/98 User Information 3-1

Installing Hardware Options

Removing the Cover
To gain access to the inside of the MicroVAX 3100 Model 88 and Model 98 Systems,
remove the cover following this procedure:
1.

Turn off your system, the terminal, and all external peripheral devices.

Unplug the power cord from the wall outlet.

Wait at least 15 seconds, to allow time for the power supply capacitors to discharge
safely.

Facing the rear of the unit, locate and loosen the three thumbscrews that fasten the top
cover to the enclosure. Pull back on the cover sides two or three inches, and lift the
cover up and away from the enclosure.

MLO-013628

Figure 3-1 Removing the Cover

3-2 MicroVAX 3100 Models 88/98 User Information

Installing Hardware Options

Cache Memory
The MicroVAX 3100 Model 88 system has 128 KB of cache on the system board; the
MicroVAX 3100 Model 98 system has 512 KB of on board cache.

System Memory
The MicroVAX 3100 Model 88 and Model 98 Systems have one bank of four Single-InLine Memory Modules (SIMMs) with 16 MB each, for a total of 64 MB. The MicroVAX
Model 98 also has the option of being supplied with SIMMs of 32MB each, for a total of
128 MB. There are slots for a second optional bank of memory. The memory options
include adding a second bank of 16 MB SIMMs (196 MB total), a second bank of 32 MB
SIMMs (256 MB total) or a set of 32 MB SIMMs to replace the first bank (256 MB total
for both banks) on the MicroVAX 3100 Model 88. As available, a second SIMM carrier
will increase maximum memory to 512MB.
Memory Configuration Rules
Refer to Figure 3-2 for SIMM Bank Configuration.
•

Random-access memory can be added only in four SIMM increments (four per bank).

•

There are two banks, J1-J4 and J-5-J8. Always fill at least one bank completely.

•

To fill a bank, start at one end of Bank J8-J5 and fill every SIMM socket in the bank.
Each bank MUST be completely filled with like SIMMs, if it is filled at all.

•

Do not mix SIMMs within a bank

•

Use same SIMM size within a bank.

MicroVAX 3100 Models 88/98 User Information 3-3

Installing Hardware Options

J1
J2
J3
J4
J5
J6
J7
J8

MLO-013629

Figure 3-2 SIMM Bank Configuration

Installing or Removing Memory Modules (SIMMs)
To add or remove a set of memory modules (SIMMs) to a bank, see Figure 3-3 and follow
this procedure:
1.

Turn off your system and unplug the power cord from the wall outlet.

Unlock and remove the thumbscrews that secure the top cover and remove the cover,
as described earlier in this chapter.

Remove the SIMM board by pushing back on the latches and lifting it out of its
connector.

3-4 MicroVAX 3100 Models 88/98 User Information

Installing Hardware Options

MLO-013650

Figure 3-3 Removing the SIMM Board

Hold the SIMM board so that the bottom side of the SIMMs face toward you.
Remove the first SIMM from connector J4 by tilting the top of it gently toward you
and lifting it out.

Remove the optional SIMM board from connector J1 in the same manner as described
in the previous step. Remove all other SIMMs in the same manner.

MicroVAX 3100 Models 88/98 User Information 3-5

Installing Hardware Options

MLO-013651

Figure 3-4 Removing/Installing a SIMM Board
5.

Install/reinstall the SIMMs as desired by tipping the top of the SIMM to be placed
furthest from you toward you, and inserting its base in the appropriate connector.
Install the other SIMMs in the same manner, working toward you.

Reinstall the SIMM board.

Replace the cover, and secure with thumbscrews, as described earlier in this chapter.

Connect the power cord and plug it into the wall outlet.

Storage Devices
MicroVAX 3100 Model 88 and Model 98 Systems support six storage devices, one
standard RRDxx CD-ROM drive, one standard RZ2x disk drive, two slots for either 3.5inch or 5.25-inch removable media or non-removable media devices, and two additional
slots which can accommodate only 1 inch x 3.5-inch hard drives. See Figure 3-6 or
Figure 3-10.

General Information on Installing Drives
This section covers general drive installation information, including internal and external
SCSI drives, external SCSI, and cable layouts.

3-6 MicroVAX 3100 Models 88/98 User Information

Installing Hardware Options
SCSI Addresses (SCSI ID’s)
Before installing a SCSI device, you must either set or verify the setting of the device’s
SCSI address (SCSI ID). The SCSI controller chip is normally assigned device ID seven.
Digital recommends that you use Table 3-1 as a guide for the selection of an address for
your SCSI drive.
Table 3-1 SCSI Address Recommendations
SCSI Address (ID)

Device (Drive) Recommended

Expansion

Expansion/hard drive

System disk (where your operating system resides)

CD-ROM drive

Expansion

Host Adapter (SCSI Controller) default

Expansion

Refer to Appendix F, Setting SCSI Ids, and the section on SCSI Connectors in
Appendix E, Technical Specifications, for additional information.
________________________ CAUTION ___________________________
Failure to properly set up the SCSI termination may result in loss of data or
damage to the file system.
____________________________________________________________
SCSI Termination
MicroVAX 3100 Model 88 and Model 98 Systems contain an embedded SCSI bus that is
used to connect both the internal and external drives. Both ends (and only at the ends) of
the SCSI bus MUST be terminated correctly. The controller end of the bus has embedded
termination.
External SCSI Connector Termination
An external terminator is required when the SCSI port is not being used.

MicroVAX 3100 Models 88/98 User Information 3-7

Installing Hardware Options
Internal SCSI Termination
The internal SCSI cable used for the MicroVAX 3100 Model 88 and Model 98 Systems is
a flat ribbon cable with integrated on-board termination. Therefore, NO storage devices
should have termination enabled.
SCSI Bus Length
The total SCSI bus length, including internal cables and etch on the motherboard as well
as the external cables between the system and the storage enclosures must not exceed 6
meters (19.6). The internal SCSI length is 1.2 meters (3.9 feet), leaving 4.8 meters (16.2
feet) for external SCSI use.

Installing Optional Storage Devices
This section tells you how to install optional hard devices into the front and rear storage
bays.
To install an optional storage device, follow this procedure:
1.

Turn off your system and unplug the power cord from the wall outlet.

Remove the cover, as described earlier in this chapter.

Installing Devices in the Front Bay
There are four slots in the front drive bay; the top slot contains the standard 3.5-inch RZxx
hard disk drive. The next two can accommodate optional 3.5-inch or 5.25-inch devices,
while the lowest slot contains the CD-ROM drive.
_________________________ NOTE____________________________
•

The two middle slots in the front drive bay can accommodate either 3.5inch or 5.25-inch devices. If you are installing 3.5-inch devices, there are
additional brackets which must be mounted on the device before it is
installed in the slot.
___________________________________________________________

3-8 MicroVAX 3100 Models 88/98 User Information

Installing Hardware Options
To install the brackets on a 3.5-inch device, refer to Figure 3-5 and follow these steps:
1.

Align the device as shown in Figure 3-5 with the internal cable connectors  facing
away from you. The SCSI connector should be oriented at the rear of the assembly.

Attach the brackets to the device using the four screws provided.

MLO-013520

Figure 3-5 Installing the 3.5 Inch Brackets
To install either 3.5-inch optional drives (with mounting bracket attached), or 5.25-inch
devices in the front drive bay, follow these steps.
1.

Turn off the system, unplug the power cord and remove the cover.

Set the SCSI drive device jumpers or switches for the desired SCSI ID (address). This
address depends on the unit numbers currently in use. (See Appendix F, Setting SCSI
IDs, for a list of typical SCSI ID assignments. Appendix G, Equipment Log, contains
space to record your systems SCSI ID assignments.) Follow the guidelines in the
manual that came with the drive.

Remove the enclosure front bezel by pushing on the inside tab and lifting it up and
away from the front of the enclosure as shown in Figure 3-6.

MicroVAX 3100 Models 88/98 User Information 3-9

Installing Hardware Options

ML013593

Figure 3-6 Removing the Front Bezel
4.
5.
6.

Remove the EMI shield covering the slot you are filling by pushing it out from the
inside of the enclosure. Refer to Figure 3-7, Item .

Attach the drive rail, Figure 3-7, Item  onto the device (or onto the mounted bracket
if you are installing a 3.5-inch device) using the screws provided.
Insert the rear of the device through the front of the bay and slide it rearward in the
bay, engaging the bay tabs onto the drive rail. If you are installing a non-removable
media device (such as a disk drive) seat it so that the front is flush with the front of the

3-10 MicroVAX 3100 Models 88/98 User Information

Installing Hardware Options
enclosure; seat removable media devices (such as a CD-ROM) so that the front will be
even with the front of the bezel after it is reinstalled.
7.

Insert the screws, Figure 3-7 Item  (four total) , through the side of the bay and into
the device as shown. It may be necessary to position the rail slightly to seat it in the
system.

4
1
2

MLO-013611

Figure 3-7 Installing Optional Devices in the Front Bay
8.

If you are installing a hard drive or other non-removable media device, snap the front
EMI shield back into place over the slot in the enclosure. If you are installing a CDROM or other removable media device, you will leave the EMI shield off the system
so that the front of the device can be accessed. Place the shield in a safe location in
case you wish to remove the device later, or replace it with a hard drive.

Connect the SCSI and power cables to the device.

10. Reinstall the front bezel, close the cover, connect the power cord and plug it into the
wall outlet.

MicroVAX 3100 Models 88/98 User Information 3-11

Installing Hardware Options

Installing a Hard Disk Drive in the Rear Storage Bay
One or two optional 1 inch x 3.5-inch hard disk drives can be installed in the rear storage
bay.
To install a hard disk in this bay, refer to Figure 3-8 and follow these procedures:
1.

Turn off the system, unplug the power cord and remove the cover.

Remove the two screws  which holds the rear drive bay in place.

Slide the flanges of the bay out of their retaining slots , and lift the bay out of the
enclosure.

MLO-013610

Figure 3-8 Removing the Rear Drive Bay

3-12 MicroVAX 3100 Models 88/98 User Information

Installing Hardware Options
4.

Set the drive into position in the bay (fill the bottom slot of the bay first, as shown in
Figure 3-9, and place the second drive on top of the first).

Insert the four screws through the side of the bay and into the device as shown.

MLO-013597

Figure 3-9 Installing Optional Hard Drives in the Rear Bay

Reinstall the bay into the enclosure slots and replace the two screws.

Connect the SCSI and power cables to the device.

Close the cover, connect the power cord and plug it into the wall outlet.

MicroVAX 3100 Models 88/98 User Information 3-13

Installing Hardware Options

Communications Options
There are five slots on the rear of the MicroVAX 3100 88/98 systems available for
communications options. The slots are numbered 1 through 5, from bottom to top
(numbers are visible from the inside of the chassis). Slot 5 may be used for synchronous
communication, Slot 4 asynchronous communication, Slots 3 and 4 are reserved for future
use and Slot 1 functions as an optional external SCSI port. Refer to Figure 3-10.

5
4
3
2
1
MLO-013716

Figure 3-10 Communication Slots

3-14 MicroVAX 3100 Models 88/98 User Information

Installing Hardware Options

Table 3-2 Communication Option Slot Locations
Figure Legend

Communication Device

KZDDA (External SCSI)

Reserved

DSW43 (Synchronous)

DHW42 (Asynchronous)

Synchronous Communication Option
The MicroVAX 3100 88/98 systems support the DSW43-AA synchronous communications
option. This communications option provides two synchronous communications ports and
allows you to connect the system to a peripheral that uses an EIA-232 (V.24) 25-pin
connector via a 2-ft cable. You can use other interface standards with this option if you
order different cables. Table 3-3 lists each interface standard and the part number of the
corresponding cable. The BC19x-02 cables listed in are 2-foot cables; you must order the
extension cables separately. Contact your Digital sales representative for information on
ordering any of the different cables that support these interface standards.
Table 3-3 Interface Standards and Cable Part Numbers
Interface Standard

Cable Part Number

Extension Cable Part Number

EIA-232/V.24

BC19D-02

BC22F-nn (10, 25, or 50 ft)

EIA-432/V1.0

BC19E-02

BC55D-nn (25 or 50 ft)

EIA-422/V.11

BC19B-02

BC55D-nn (25 or 50 ft)

Installing the Synchronous Communication Option
The MicroVAX 3100 88/98 systems support the DSW43-AA synchronous communications
option. To install it, refer to Figure 3-11 and follow these instructions:
1.

Turn off the system, unplug the power cord and remove the cover.

Insert the module into the slot of the I/O receiver, pressing it firmly into place to seat
the connection.

MicroVAX 3100 Models 88/98 User Information 3-15

Installing Hardware Options

MLO-013625

Figure 3-11 Installing the Synchronous Communication Option

Insert the screw through the module and into the I/O shelf as shown.

Connect the 100-pin-to-2x50-pin pigtail cables to the new synchronous
communications option.

Close the cover, connect the power cord and plug it into the wall outlet.

Asynchronous Communication Options
The MicroVAX 3100 88/98 systems support two different asynchronous communications
options. These options are as follows:
•

DHW42-BB -- This asynchronous option provides 16 asynchronous DEC423 dataline-only communications lines through two system ports. You can connect up to 16
peripherals using the MMJ ports on two harmonicas (H3104) that connect to the
option cables (BC16C-10).

3-16 MicroVAX 3100 Models 88/98 User Information

Installing Hardware Options
Use the following cables instead of the BC16C-10 cable if you require longer cable
lengths:
BC16C-25, BC16C-50, BC16C-A0, or BC16C-B5.
Use the following cables between the harmonica (H3104) and the DEC423 peripheral:
BC16E-10, BC16E-25, or BC16E-50.
•

DHW42-CB -- This asynchronous option provides eight asynchronous EIA-232
modem control lines through two system ports using two breakout cables (BC29J-06).

Attach one of the following cables to a connector on the breakout cable if you require
longer cable lengths:
BC22F-10, BC22F-25, or BC22F-50.
The peripheral you are using may require a null-modem extension cable. See the
peripheral documentation or contact your Digital sales representative for information on
the correct null-modem cable to use.
Installing the Asynchronous Communication Option
The MicroVAX 3100 88/98 systems support two different asynchronous communications
options, DHW42-BB and DHW42-CB in the top slot of the I/O receiver. To install either
of these, refer to Figure 3-12 follow these instructions:
1.

Turn off the system, unplug the power cord and remove the cover.

Insert the module  into the top slot of the I/O receiver, pressing it firmly into place
to seat the connection.

MicroVAX 3100 Models 88/98 User Information 3-17

Installing Hardware Options

MLO-013626

Figure 3-12 Installing the Asynchronous Communication Option

Insert the screw  through the option and into the I/O shelf as shown.

Connect the 120 pin-to 2 x 36 or the 120 pin-to- 2 x 50 pin pigtail cables to your new
asynchronous communication option.

Close the cover, connect the power cord and plug it into the wall outlet.

Optional SCSI Port (KZDDA)
The MicroVAX 3100 88/98 systems supports seven additional external SCSI devices with
the KZDDA option.

3-18 MicroVAX 3100 Models 88/98 User Information

Installing Hardware Options
Installing the KZDDA
The KZDDA external SCSI option is installed in the bottom I/O slot. To install the
KZDDA option, refer to Figure 3-13 and follow these instructions:
1.

Turn off the system, unplug the power cord and remove the cover.

Insert the module  into the bottom slot of the I/O receiver, pressing it firmly into
place to seat the connection.

MLO-013627

Figure 3-13 Installing the KZDDA External SCSI Option

Insert the screw  through the option and into the I/O shelf as shown.

Attach external SCSI cable.

Close the cover, connect the power cord and plug it into the wall outlet.

MicroVAX 3100 Models 88/98 User Information 3-19

Installing Hardware Options

External Options
The MicroVAX 3100 88/98 systems can accommodate the following options:
•

SCSI devices and expansion boxes

•

Printers, terminals, modems, and other devices that use asynchronous or synchronous
connectors

Your Digital sales representative can give you information on how to order a full range of
SCSI and Q-bus expansion boxes, printers, terminals, modems, and other devices that are
compatible with MicroVAX 3100 88/98 systems.

Connecting an External SCSI Option or Expansion Box
________________________ CAUTION __________________________
•

The recommended maximum length of SCSI cables (internal length plus
external length) is 19.6 feet (6 meters).
• Do not connect more than two tape drive devices, per SCSI port.
• Some expansion boxes are restricted to either 110 V ac or (220 V ac)
operation. Make sure that the voltage requirement of the expansion box
used is compatible with the supply voltage.
• Turn on the expansion boxes before you turn on the system unit. This
procedure ensures that the device in each expansion box is ready for use
and that the system firmware includes the device in the configuration
display.
• Do not connect or disconnect SCSI expansion boxes while the system is
turned on. Doing so can cause damage to the equipment or corrupt
data.
• Digital cannot guarantee the correct operation of any SCSI bus that
uses cable assemblies not supplied by Digital or not configured in
accordance with these guidelines.
___________________________________________________________
__________________________ Note ____________________________
Be sure to read the instructions that come with the SCSI device. If the cable
supplied with the SCSI device has the wrong type of connector, you will need an
adapter or a different cable.
___________________________________________________________

3-20 MicroVAX 3100 Models 88/98 User Information

Installing Hardware Options
To connect an external SCSI device, or a SCSI expansion box, follow these steps:
1.

Set the drive jumpers or switches for the desired SCSI ID.

Remove the SCSI terminator and connect the option’s SCSI cable to the port. Be sure
that you use a cable with a SCSI 50-pin high density type connector.

Terminate the new end of the bus at the last external SCSI device, using the
appropriate terminator. Make sure that any other external SCSI devices have their
terminators removed or disabled.

To Check expansion box connections, enter the following from the console prompt:
>>>

SHOW SCSI

SCSI Adapter A, SCSI ID 6
-DKA300 (DEC RZ26N)
-DKA400 (DEC RRD45)

SCSI Adapter B, SCSI ID 6
-DKB100 (DEC RZ28D)

MicroVAX 3100 Models 88/98 User Information 3-21

Installing Hardware Options

System Board Access
To access the system board, the enclosure cover must first be removed, then release the
two module clips  and gently slide board out. Refer to Figure 3-14.
1

MLO-013710

Figure 3-14 Removing System Board

3-22 MicroVAX 3100 Models 88/98 User Information

Installing Hardware Options

If you need to access components on the system board that are underneath the plastic cover
 , remove the two nuts  and the clip . See Figure 3-15.

2
1

MLO-013711

Figure 3-15 Removing the System Board Cover

MicroVAX 3100 Models 88/98 User Information 3-23

4
Troubleshooting
Introduction
This chapter describes initial and general troubleshooting as well as the error beep codes.

)

Refer to the documentation supplied with additional options if you are experiencing
problems with specific options that you have installed.

Initial Troubleshooting
To troubleshoot your MicroVAX 3100 Model 88/98 system initially, follow this
procedure:
1.

Check that the power indicator is on.

Check the power indicator on the terminal.

Make sure that all cables and connections are secure.

Press the Halt/Reset button. If your system fails to boot, turn it off, wait 20 seconds,
and turn it back on.

Contact your Digital service representative or service provider for software- or
hardware-related problems by calling 1-800-354-9000 or 1-800-DIGITAL.
__________________________NOTE ____________________________
If you need to return a failed component, pack it in its original container and
return it to Digital Equipment Corporation or to your service provider.
____________________________________________________________

MicroVax 3100 Models 88/98 User Information 4-1

Troubleshooting

General Troubleshooting
Tables 4-1 through 4-4 list how to identify and solve problems that could occur with your
system, disk drive, and terminal.
Table 4-1 System Troubleshooting
Problem

Possible Cause

Action

Power indicator not on.

System is not plugged in.

Turn off the system, plug it in,
and then turn it back on again.

No power at the wall outlet.

Use another wall outlet.

Power supply failure.

Contact your service
representative.

Internal power supply cables
not reconnected after
installing options.

Reconnect cables.

The overload protection
circuitry of the power
supply may have shut down
because of abnormal
condition on the power line.

Turn the system off, then turn it
back on.

4-2 MicroVAX 3100 Models 88/98 User Information

Troubleshooting
Problem

Possible Cause

Action

Power is on, but there is no
screen display.

Brightness and contrast
controls are not correctly
set.

Adjust the brightness and contrast controls.

Terminal is off.

Turn on the terminal.

Terminal cable or power
cord is incorrectly installed.

Check all terminal connections:
ensure that the terminal is
connected to port 3.

Fuse may be blown on the
terminal.

Replace the fuse.

Terminal settings may be
incorrect.

Check the terminal settings; see
terminal documentation.
Try another terminal.

Terminal is defective.

Replace the video terminal

Port to which the terminal
connects may be faulty.

Try connecting the terminal to
another system. If this solution
works, the port to which the
terminal was connected is
faulty. If the terminal still does
not operate, it is faulty. In either
case, contact your Digital
services representative.

The terminal cable may be
faulty.

Connect the cable to another
system and terminal. If that
terminal now does not work,
the cable is faulty. Contact your
Digital services representative
for a new one.

The break/enable switch is
in the wrong position.

Turn off the system. Set the
break/enable switch to the down
position, then turn the system
on.

MicroVAX 3100 Models 88/98 User Information 4-3

Troubleshooting
Table 4-1 System Troubleshooting (continued)
Problem

Possible Cause

Action

The power up test display
contains unexpected
characters.

The terminal settings are
incorrect, or the console
circuitry is faulty.

Make sure the settings are
correct, then run the power-up
test again. If the terminal is set
correctly, and trouble persists,
contact your Digital services
representative.

The system fails to boot the
operating system.

The system defaults are
incorrectly set.

Set the system defaults as
described in the OpenVMS
Factory Installed Software User
Guide, then try booting the
system again. If the system fails
to boot, contact your Digital
services representative.

No response to keyboard
commands.

Keyboard is not connected.

Connect the keyboard to the
keyboard port.

Table 4-2 Disk Drive Troubleshooting
Problem

Possible Cause

Action

Hard disk drive cannot read
or write information

Incorrect disk drive jumper
settings.

Refer to the disk drive
installation instructions.

Loose or incorrectly
installed cables.

Make sure all cables are
correctly installed.

SCSI hard disk drive is not
correctly formatted or
partitioned.

Format and partition as required
using the supplied operating
system.

4-4 MicroVAX 3100 Models 88/98 User Information

Troubleshooting
Table 4-3 Terminal Troubleshooting
Problem

Possible Cause

Action

Terminal power indicator is
not on.

Terminal is turned off.

Turn on the terminal.

Power cord is not
connected.

Connect the power cord to the
system or a wall outlet.

No power at wall outlet.

Use another outlet.

Power indicator is defective.

Contact your service
representative or Digital
Equipment Corporation.

Terminal incorrectly
adjusted.

Adjust accordingly.

Wrong type of terminal.

Try another terminal.

Defective terminal.

Try another terminal.

Terminal signal cable
incorrectly installed.

Straighten any bent connector
pins and then reconnect the
terminal.

Distorted, rolling, or
flickering screen display, or
wrong or uneven color

MicroVAX 3100 Models 88/98 User Information 4-5

5
Diagnostic Tests and Commands
There are a number of diagnostic tests and commands that can help you to isolate a
problem with the system unit. These tests and commands are as follows:
•

Power-up tests

•

Diagnostic tests and utilities. You can use these tests and commands in privileged
console mode only if the console security feature is enabled and the password is set.

•

Configuration display

•

Error display

Power-Up Tests
The system runs the power-up tests each time you turn on the system. After successful
completion of tests, the system will either enter console mode or proceed to automatic
bootstrap, depending on the HALT action selected by the user.
•

If HALT action is Default, Halt, or Restart, then the system enters console mode.

•

If HALT action is Reboot or Restart_reboot, then the system proceeds to boot.

The following example shows a typical display for a system that passes all tests and then
enters console mode.
KA58-A or KA59-A V1.0, VMB

2.16

MicroVax 3100 Models 88/98 User Information 5–1

Diagnostic Tests and Commands
Tests completed.

>>>

Central Processing Unit (CPU) Name, Firmware Version Number, and
 Virtual Memory Boot (VMB) Version Number
 Read-Only Memory (ROM) Based Diagnostics Countdown Status Message
 Console Prompt
The following example shows a typical display for a system that passes all tests and then
enters automatic bootstrap.
KA58-A or KA59-A V1.0, VMB 2.16
Performing normal system tests.
74..73..72..71..70..69..68..67..66..65..64..63..62..61..60..59..
58..57..56..55..54..53..52..51..50..49..48..47..46..45..44..43..
42..41..40..39..38..37..36..35..34..33..32..31..30..29..28..27..
26..25..24..23..22..21..20..19..18..17..16..15..14..13..12..11..
10..09..08..07..06..05..04..03..

Tests completed.
Loading system software.
(BOOT/R5:0 EZA0)

2..
-EZA0
1..0..

_________________________ NOTE____________________________
The operating system messages start here.
___________________________________________________________
If the power-up tests encounter an error, one of the following actions occurs:
For minor errors:
•

If HALT action is set to a boot condition (that is reboot or restart_reboot), and if a
minor error occurs, the system displays an abbreviated error message and continues to
boot as normal.

5–2 MicroVAX 3100 Models 88/98 User Information

Diagnostic Tests and Commands
•

If HALT action is set to Default, Halt or Restart, then the system enters console mode.

The only errors defined as minor are errors in memory that cause pages to be marked bad
in the memory bitmap. There must be enough good memory left to allow an attempt to
bootstrap.
For severe errors:
The system always enters console mode regardless of HALT action after it attempts to
complete all tests possible.
The following example shows a system with a memory error that only affected one set of
memory out of two sets. Because some memory is still usable, the system proceeds to
automatic bootstrap if the HALT action is set to a boot condition.
KA58-A or KA59-A V1.0, VMB 2.16
Performing normal system tests.
71..70..69..68..67..66..65..64..63..62..61..60..59..58..57..56..
55..54..53..52..51..50..49..48..47..46..45..44..43..42..41..40..
39..38..37..36..35..34..33..32..31..

? Test_Subtest_40_06

Loop_Subtest=00

Err_Type=FF

DE_Memory_count_pages.lis

30..29..28..27..26..25..24..23..22..21..20..19..18..17..16..15..
14..13..12..11..10..09..08..07..06..05..04..03..

Memory Set 0: 08000000 to 09FFFFFF, 32MBs, 0 good pages, 65536 bad pages
Set 0 on SIMM_carrier_J4

(J5...)

(J6...)

(J7...)

(J8 ??)

Memory Set 1: 00000000 to 07FFFFFF, 128MBs, 262144 good pages, 0 bad pages
Set 1 on SIMM_carrier_J4

(J1..)

(J2..)

(J3..)

(J4...

Total of 160MBs, 262144 good pages, 65536 bad pages, 7 reserved pages

Tests completed.
Loading system software.
(BOOT/R5:0 EZA0)
2..
-EZA0
1..0..

MicroVAX 3100 Models 88/98 User Information 5–3

Diagnostic Tests and Commands

Operating system messages start here.

Abbreviated error message for memory error
Memory errors normally cause the results of a SHOW MEMORY display to occur after the
tests are completed and before continuing. SHOW MEMORY is the most useful command
to determine which memory SIMMs are bad when memory errors occur.

Diagnostic Tests and Utilities
The diagnostic tests and utilities are similar to the power-up tests except that the power-up
tests enable you to test all the devices in the system, whereas the diagnostic tests and
utilities enable you to test single devices and the functions of single devices.
By entering this command, you can see a list of diagnostic tests.

>>> T 9E
>>> SHOW TESTS

Test
#

Address

Name

Parameters

___________________________________________________________________________
20052200

SCB

20055850

De_executive

2006A53C

Memory_Init_Bitmap *** mark_Hard_SBEs ******

2006AB34

Memory_Setup_CSRs

*********

2005D148

NMC_registers

**********

2005D324

NMC_powerup

2005E6D8

SSC_ROM

***

2005FB90

B_Cache_diag_mode

bypass_test_mask *********

20061590

Cache_w_Memory

bypass_test_mask *********

2006B5E0

Memory_count_pages First_set Last_set Soft_errs_allowed *****

20068CEC

Board_Reset

20061880

Chk_for_Interrupts **********

200610C4

P_Cache_diag_mode

bypass_test_mask *********

2006AD04

Memory_Refresh

start_a end incr cont_on_err time_seconds *****

2006B028

Memory_Addr_shorts start_add end_add * cont_on_err pat2 pat3 ****

5–4 MicroVAX 3100 Models 88/98 User Information

Diagnostic Tests and Commands
4A

2006A23C

Memory_ECC_SBEs

2006940C

Memory_Byte_Errors start_add end_add add_incr cont_on_err ******

start_add end_add add_incr cont_on_err ******

20069BA0

Memory_ECC_Logic

start_add end_add add_incr cont_on_err ******

20068FE8

Memory_Address

start_add end_add add_incr cont_on_err ******

20069188

Memory_Byte

start_add end_add add_incr cont_on_err ******

2006B7F4

Memory_Data

start_add end_add add_incr cont_on_err ******

2005803C

FPA

**********

20058530

SSC_Prog_timers

which_timer wait_time_us ***

20058818

SSC_TOY_Clock

repeat_test_250ms_ea Tolerance ***

20057C18

Virtual_Mode

********

20058E6C

Interval_Timer

*****

2006507C

SHAC_LPBCK

From_bus To_bus passes *******

20065D24

SHAC_RESET

dssi_bus port_number time_secs not_pres *

20062778

SGEC_LPBCK_ASSIST

time_secs **

20062D10

SHAC

SHAC_number *********

200619B8

SGEC

environment no_ram_tests ******

20058B1C

console_QDSS

mark_not_present selftest_r0 selftest_r1 *****

20058CA4

QDSS_any

input_csr selftest_r0 selftest_r1 ******

2005D3C0

CQBIC_memory

bypass_test_mask *********

200596CC

Qbus_MSCP

IP_csr ******

200598AC

Qbus_DELQA

device_num_addr ****

2005A85C

QZA_Intlpbck1

controller_number ********

2005BF1C

QZA_Intlpbck2

controller_number *********

20059A9C

QZA_memory

incr test_pattern controller_number *******

20059F44

QZA_DMA

Controller_number main_mem_buf ********

20058494

CQBIC_registers

20058410

CQBIC_powerup

2005DC4C

Flush_Ena_Caches

dis_flush_VIC dis_flush_BC dis_flush_PC

20063FB0

INTERACTION

pass_count disable_device *******

20068E48

Init_memory

2006631C

List_CPU_registers *

2006C250

Utility

Flags *********

2005903C

List_diagnostics

script_number *

200681CC

Create_A0_Script

**********

20057888

SSC_RAM_Data

20057A78

SSC_RAM_Data_Addr

200589E8

SSC_registers

MicroVAX 3100 Models 88/98 User Information 5–5

Diagnostic Tests and Commands
D0

20060C70

V_Cache_diag_mode

bypass_test_mask *********

2005DE90

O_Bit_diag_mode

bypass_test_mask *********

2006139C

PB_Flush_Cache

**********

2005E850

Speed

print_speed *********

2006C060

NO_Memory_present

2005F0DC

B_Cache_Data_debug start_add end_add add_incr *******

2005EC64

B_Cache_Tag_Debug

start_add end_add add_incr *******

2005E2A8

O_BIT_DEBUG

start_add end_add add_incr seg_incr ******

2006D4D4

SCSI

environment reset_bus time_s *******

2006D7CC

SCSI_Utility

environment util_nbr target_ID lun ******

2006DA2C

SCSI_MAP

bypass_test addr_incr_data_tst ********

2006DFC8

environment *********

2006E1DC

SYNC

environment *********

2006E2B4

SYNC_Utility

environment *********

2006E398

ASYNC

environment *********

2006D638

SCSI_option

environment reset_bus time_s *******

2006D900

SCSI_Opt_Utility

environment util_nbr target_ID lun ******

2006DA40

SCSI_MAP_Option

bypass_test addr_incr_data_tst ********

Scripts
#

Description

User defined scripts

Powerup tests, Functional Verify, continue on error, numeric countdown

Functional Verify, stop on error, test # announcements

Loop on A3 Functional Verify

Memory tests, mark only multiple bit errors

Memory tests

Memory acceptance tests, mark single and multi-bit errors, call A7

Memory tests, stop on error

Extended tests plus BF, then loop

Extended tests, then loop

DZ, SYNC, ASYNC with loopbacks

Load & start system exerciser
100 Customer mode, 2 passes
101 CSSE mode, 2 passes

5–6 MicroVAX 3100 Models 88/98 User Information

Diagnostic Tests and Commands
102 CSSE mode, continous until ^C
103 Manuf mode, continous until ^C
104 Manuf TINA mode, continous until ^C
105 Manuf mode, 2 passes
106 CSSE mode, select tests, continous until ^C
107 Manuf mode, select tests, continous until ^C

__________________________NOTE ____________________________
Tests 101 through 107 are reserved for use by Digital services.
____________________________________________________________

The tests and utilities shown in the following table are for option cards, which may or may
not be present, depending upon the options you ordered.
Table 5-1 Option Card Tests
Test

Name

Usage

SYNC

Synchronous COMM option card (DSW43)

SYNC_Utility

Synchronous COMM option card (DSW43)

ASYNC

Asynchronous option card (DHW42)

SCSI_option

SCSI option card for 2nd SCSI bus B (KZDDA)

SCSI_Opt_Utility

SCSI option card for 2nd SCSI bus B (KZDDA)

SCSI_MAP_Option

SCSI option card for 2nd SCSI bus B (KZDDA)

__________________________NOTE ____________________________
The following available tests are not used on the MicroVAX 3100 Models
88/98; they are used only on the VAX 4000 Models, and are listed here to
avoid confusion when you see them in the diagnostic test listing
____________________________________________________________
Table 5-2 VAX Tests (Not Applicable to MicroVAX Model 88/98)
Test

Name

Usage

SHAC_LPBCK

Not used on MicroVAX 3100, SHAC option only

SHAC_RESET

Not used on MicroVAX 3100, SHAC option only

MicroVAX 3100 Models 88/98 User Information 5–7

Diagnostic Tests and Commands
5C

SHAC

Not used on MicroVAX 3100, SHAC option only

console_QDSS