Digital PDFs

EK-600EB-OM-002

October 1991

241 pages

Original

0.6MB

Document:	VAX 6000 Series Owners Manual
Order Number:	EK-600EB-OM
Revision:	002
Pages:	241
Original Filename:	https://manx-docs.org/collections/mds-199909/cd1/vax/600ebom2.pdf

OCR Text

VAX 6000 Series Owner’s Manual

Order Number EK–600EB–OM.002

This manual is intended for the system manager or
system operator and covers the daily operations of a
VAX 6000 series system.

digital equipment corporation
maynard, massachusetts

First Printing, October 1990
Revised, November 1991
The information in this document is subject to change without notice and should not be
construed as a commitment by Digital Equipment Corporation.
Digital Equipment Corporation assumes no responsibility for any errors that may appear in
this document.
The software, if any, described in this document is furnished under a license and may be used
or copied only in accordance with the terms of such license. No responsibility is assumed
for the use or reliability of software or equipment that is not supplied by Digital Equipment
Corporation or its affiliated companies.
Copyright ©1990, 1991 by Digital Equipment Corporation.
All Rights Reserved.
Printed in U.S.A.

The following are trademarks of Digital Equipment Corporation:
DEC
DEC LANcontroller
DECnet
DECUS
DWMVA

PDP
ULTRIX
UNIBUS
VAX
VAXBI

VAXcluster
VAXELN
VMS
XMI

FCC NOTICE: The equipment described in this manual generates, uses, and may emit
radio frequency energy. The equipment has been type tested and found to comply with the
limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which
are designed to provide reasonable protection against such radio frequency interference when
operated in a commercial environment. Operation of this equipment in a residential area
may cause interference, in which case the user at his own expense may be required to take
measures to correct the interference.

Contents
Preface

Chapter 1 The VAX 6000 Series System
1.1
1.2
1.3
1.4
1.5
1.6

System Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2
System Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4
Sample System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–6
System Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–8
System Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–10
Supported Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–12

Chapter 2 System Components
2.1
2.1.1
2.1.2
2.2
2.3
2.4
2.5
2.6

Console Load Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet-Based Compact Disk Server . . . . . . . . . . . . . . . .
In-Cabinet Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XMI Card Cage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2–2
2–4
2–6
2–8
2–10
2–12
2–14
2–16

Chapter 3 Controls and Indicators
3.1
3.2
3.3
3.4
3.5
3.6

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
Upper Key Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–4
Lower Key Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–6
Restart Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8
Status Indicator Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10
Circuit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–12

iii

Chapter 4 Booting
4.1
4.2
4.3
4.4
4.5
4.6
4.6.1
4.6.2
4.7
4.7.1
4.7.2
4.8
4.9
4.9.1
4.9.2

How Booting Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regular Boot Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot Device Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot Processor Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Booting from an HSC Disk . . . . . . . . . . . . . . . . . . . . . . . . . . .
VAXcluster Boot Overview . . . . . . . . . . . . . . . . . . . . . . . . .
Sample VAXcluster Boot . . . . . . . . . . . . . . . . . . . . . . . . . .
Booting from an Ethernet-Based Compact Disk Server . . . . .
CD Server Boot Command . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting an Ethernet Service . . . . . . . . . . . . . . . . . . . . . .
Ethernet Boot Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sample Target-Initiated Ethernet Boot . . . . . . . . . . . . . . . . .
Step 1, Gather Information at Target Node . . . . . . . . . . . .
Step 2, Enter Information into Executor’s NCP Volatile
Database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.9.3
Step 3, Boot from the Target Node . . . . . . . . . . . . . . . . . . .

4–2
4–4
4–6
4–8
4–10
4–12
4–12
4–14
4–16
4–16
4–18
4–20
4–22
4–22
4–24
4–26

Chapter 5 Console
5.1
Description of Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2
Console Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3
Console Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4
Console Command Language Control Characters . . . . . . . . .
5.5
Console Command Language Syntax . . . . . . . . . . . . . . . . . . .
5.6
BOOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6.1
BOOT Command Examples and Qualifiers . . . . . . . . . . . .
5.6.2
BOOT Command Description . . . . . . . . . . . . . . . . . . . . . . .
5.7
CLEAR EXCEPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8
CONTINUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.9
DEPOSIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.9.1
Syntax and Qualifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.9.2
Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.10 EXAMINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.10.1 Syntax and Qualifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5–2
5–4
5–6
5–8
5–10
5–12
5–12
5–14
5–16
5–18
5–20
5–20
5–22
5–24
5–24

5.10.2 Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.11 FIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.12 HALT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.13 HELP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.14 INITIALIZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.15 REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.16 RESTORE EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.17 SAVE EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.18 SET Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.18.1 SET BOOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.18.2 SET CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.18.2.1
Syntax and Qualifiers . . . . . . . . . . . . . . . . . . . . . . . . . .
5.18.2.2
Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.18.3 SET LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.18.4 SET MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.18.5 SET TERMINAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.19 SHOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.20 START . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.21 STOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.22 TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.23 UNJAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.24 UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.25 Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.26 ! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.27 Sample Console Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5–26
5–28
5–30
5–32
5–34
5–36
5–38
5–40
5–42
5–44
5–46
5–46
5–48
5–50
5–52
5–54
5–56
5–58
5–60
5–62
5–64
5–66
5–68
5–70
5–72

Chapter 6 System Self-Test and Troubleshooting
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8

Self-Test Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sample Self-Test Display . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Self-Test Progress Trace Line . . . . . . . . . . . . . . . . . . . . . . . . .
Self-Test Lines NODE #, TYP, and STF . . . . . . . . . . . . . . . . .
Self-Test Lines BPD and ETF . . . . . . . . . . . . . . . . . . . . . . . .
Self-Test Lines ILV and Mb . . . . . . . . . . . . . . . . . . . . . . . . . .
Self-Test Identification Line . . . . . . . . . . . . . . . . . . . . . . . . . .
Sample Self-Test Display with VAXBI Adapter . . . . . . . . . . .

6–2
6–4
6–6
6–8
6–10
6–12
6–14
6–16

6.9
6.10

Troubleshooting During Booting . . . . . . . . . . . . . . . . . . . . . . . 6–18
Forcing a Boot Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–20

Appendix A Compact Disk Drive Instructions
A.1
A.2
A.3
A.4

Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading a Compact Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unloading a Compact Disk . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning Disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A–1
A–2
A–2
A–4

Appendix B TF/TK Tape Drive Instructions
B.1
B.2
B.3
B.4
B.5
B.6

Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading a Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unloading a Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Write-Protecting Your Tape Cartridge . . . . . . . . . . . . . . . . . .
Labeling a Tape Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tape Handling and Storage Guidelines . . . . . . . . . . . . . . . . .

B–2
B–3
B–4
B–4
B–5
B–5

Appendix C Device Type Code Assignments
Appendix D VAXBI Options and Adapters
D.1
D.2
D.3
D.4

Supported VAXBI Adapters . . . . . . . . . . . . . . . . . . . . . . . . . .
Supported Boot Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VAXBI Expander Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power for the VAXBI Option . . . . . . . . . . . . . . . . . . . . . . . . .

D–1
D–2
D–3
D–4

Appendix E EVUCA Program
E.1
E.2

EVUCA Program Overview . . . . . . . . . . . . . . . . . . . . . . . . . .
Updating EEPROM Contents . . . . . . . . . . . . . . . . . . . . . . . . .

E–1
E–2

Appendix F Control Flags for Booting
Appendix G Console Commands
Appendix H Console Error Messages (Model 400 and Higher)
Appendix I Console Error Messages for Model 300
Appendix J Boot Status and Error Messages (Models 500 and
600)
J.1
J.2
J.3
J.4

Ethernet Boot Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Disk Boot Messages . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Tape Boot Messages . . . . . . . . . . . . . . . . . . . . . . . . . . .
CI and DSSI Boot Messages . . . . . . . . . . . . . . . . . . . . . . . . . .

J–1
J–2
J–2
J–3

Glossary

Index
Examples
4–1
4–2
4–3
4–4
4–5
4–6
6–1
E–1

Sample VAXcluster Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sample Ethernet-Based CD Server Boot . . . . . . . . . . . . . . . .
Selecting an Ethernet Service . . . . . . . . . . . . . . . . . . . . . . . .
Step 1, SHOW Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 2, Entering Target Node Information . . . . . . . . . . . . . . .
Step 3, Booting from the Target Node . . . . . . . . . . . . . . . . . .
Forcing a Boot Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Updating EEPROM Contents . . . . . . . . . . . . . . . . . . . . . . . . .

4–14
4–16
4–18
4–22
4–24
4–26
6–20
E–3

vii

Figures
1–1
1–2
1–3
1–4
1–5
1–6
2–1
2–2
2–3
2–4
2–5
2–6
2–7
2–8
2–9
3–1
3–2
3–3
3–4
3–5
3–6
4–1
4–2
4–3
4–4
4–5
4–6
4–7
5–1
5–2
5–3
5–4
6–1
6–2
6–3

viii

Sample System Footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sample System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Console Load Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet-Based Compact Disk Server . . . . . . . . . . . . . . . . . .
Accessing the Ethernet-Based CD Server . . . . . . . . . . . . . . .
TF85 Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power System (Rear View) . . . . . . . . . . . . . . . . . . . . . . . . . . .
XMI Card Cage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Console and Terminal Connectors . . . . . . . . . . . . . . . . . . . . .
Airflow Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
International and English Control Panels . . . . . . . . . . . . . . .
Upper Key Switch (Enable Position) . . . . . . . . . . . . . . . . . . .
Lower Key Switch (Update Position) . . . . . . . . . . . . . . . . . . .
Restart Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Panel Status Indicator Lights . . . . . . . . . . . . . . . . . .
Circuit Breaker and the AC Power Controller . . . . . . . . . . . .
Boot Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regular Boot Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Determining the Boot Processor . . . . . . . . . . . . . . . . . . . . . . .
Booting from a CI-Based VAXcluster . . . . . . . . . . . . . . . . . . .
Trigger Booting Using Ethernet . . . . . . . . . . . . . . . . . . . . . . .
Target-Initiated Booting by Ethernet . . . . . . . . . . . . . . . . . . .
Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Console Switch When in Console Mode . . . . . . . . . . . . . . . . .
BOOT Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lower Key Switch in Update Position . . . . . . . . . . . . . . . . . .
Testing Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Self-Test Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Self-Test Results: Progress Trace . . . . . . . . . . . . . . . . . . . . . .

1–2
1–4
1–6
1–8
1–10
1–12
2–2
2–4
2–5
2–6
2–8
2–10
2–12
2–14
2–16
3–2
3–4
3–6
3–8
3–10
3–12
4–2
4–4
4–6
4–10
4–12
4–20
4–20
5–2
5–6
5–14
5–42
6–2
6–4
6–6

6–4
6–5
6–6
6–7
6–8
6–9
A–1
A–2
A–3
B–1
B–2
D–1

Self-Test Results: NODE #, TYP, and STF . . . . . . . . . . . . . . .
Self-Test Results: BPD and ETF . . . . . . . . . . . . . . . . . . . . . .
Self-Test Results: ILV and Mb . . . . . . . . . . . . . . . . . . . . . . . .
Self-Test Results: Identification Line . . . . . . . . . . . . . . . . . . .
Self-Test Results: TYP, STF, and XBI Lines . . . . . . . . . . . . . .
Troubleshooting Booting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RRD Compact Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading a Compact Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disk Caddy Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TF85 Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tape Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VAXBI Expander Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6–8
6–10
6–12
6–14
6–16
6–18
A–1
A–3
A–4
B–2
B–4
D–3

Tables
1
2
3
1–1
1–2
1–3
1–4
2–1
2–2
3–1
3–2
3–3
3–4
3–5
4–1
4–2
4–3
4–4
5–1
5–2
5–3
5–4

VAX 6000 Series Documentation . . . . . . . . . . . . . . . . . . . . . .
xii
VAX 6000 Model Level Documentation . . . . . . . . . . . . . . . . .
xiii
Associated Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xiv
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3
Environmental Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 1–3
System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–7
Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–13
AC Power Controller Input Voltage . . . . . . . . . . . . . . . . . . . . 2–9
Power Supply Available . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9
Control Panel Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–3
Upper Key Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–5
Lower Key Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–7
Restart Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–9
Control Panel Status Indicator Lights . . . . . . . . . . . . . . . . . . 3–11
Boot Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–3
Boot Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Sample BOOT Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–8
Boot Device Mnemonics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–9
Console Parts and Functions . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
Console Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–4
Console Control Characters . . . . . . . . . . . . . . . . . . . . . . . . . . 5–8
Console Command Language Syntax . . . . . . . . . . . . . . . . . . . 5–10

5–5
5–6
5–7
5–8
5–9
5–10
5–11
5–12
5–13
5–14
5–15
5–16
5–17
5–18
6–1
A–1
B–1
C–1
D–1
D–2
D–3
E–1
F–1
F–2
G–1
H–1
H–2
H–3
H–4
I–1
I–2

BOOT Command Qualifiers . . . . . . . . . . . . . . . . . . . . . . . . . . 5–13
DEPOSIT Command Qualifiers . . . . . . . . . . . . . . . . . . . . . . . 5–20
EXAMINE Command Qualifiers . . . . . . . . . . . . . . . . . . . . . . 5–24
FIND Command Qualifiers . . . . . . . . . . . . . . . . . . . . . . . . . . 5–28
INITIALIZE Command Qualifiers . . . . . . . . . . . . . . . . . . . . . 5–35
SET CPU Command Qualifiers . . . . . . . . . . . . . . . . . . . . . . . 5–46
SET CPU Command Qualifiers’ Effect After a System Reset . 5–49
SET LANGUAGE Command Parameters . . . . . . . . . . . . . . . . 5–50
SET MEMORY Qualifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–52
SET TERMINAL Command Qualifiers . . . . . . . . . . . . . . . . . 5–54
SHOW Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–57
STOP Command Qualifiers . . . . . . . . . . . . . . . . . . . . . . . . . . 5–60
TEST Command Qualifiers . . . . . . . . . . . . . . . . . . . . . . . . . . 5–62
Z Command Qualifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–68
System Configuration for Sample Self-Test . . . . . . . . . . . . . . 6–5
RRD Light Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–2
TF85 Light Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B–3
XMI Device Type Code Assignments . . . . . . . . . . . . . . . . . . . C–1
VAXBI Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–1
VAXBI Boot Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–2
In-Cabinet VAXBI Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–4
EEPROM Update Data Files . . . . . . . . . . . . . . . . . . . . . . . . . E–1
R5 Bit Functions for VMS . . . . . . . . . . . . . . . . . . . . . . . . . . . F–1
R5 Bit Functions for ULTRIX . . . . . . . . . . . . . . . . . . . . . . . . F–2
Console Commands and Qualifiers . . . . . . . . . . . . . . . . . . . . . G–1
Console Error Messages Indicating Halt (Model 400 and
Higher) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H–2
Standard Console Error Messages (Model 400 and Higher) . . H–3
Console Error Messages for Models 500 and 600 . . . . . . . . . . H–12
Console Error Messages Unique to Model 600 . . . . . . . . . . . . H–12
Model 300 Console Error Messages Indicating Halt . . . . . . . .
I–1
Model 300 Standard Console Error Messages . . . . . . . . . . . .
I–3

Preface
Intended Audience
This manual is written for the system manager or system operator who has
had training in VAX systems and system management tasks and is running
a VAX 6000 series system.

Document Structure
This manual uses a structured documentation design. There are many
topics, organized into small sections for efficient reference. Each topic
begins with an abstract. You can quickly gain a comprehensive overview
by reading only the abstracts. Next is an illustration or example, which
also provides quick reference. Last in the structure are descriptive text
and syntax definitions.
This manual has six chapters and ten appendixes, as follows:
•

Chapter 1, The VAX 6000 Series System, and Chapter 2, System
Components, give you a basic introduction to your system and its
parts.

•

Chapter 3, Controls and Indicators, describes how the system
presents information and how you use the switches.

•

Chapter 4, Booting, explains how you turn the system on and get it
running.

•

Chapter 5, Console, explains the console environment, use, and
console commands. It includes a sample console session.

•

Chapter 6, System Self-Test and Troubleshooting, describes selftest in detail and tells you what to do if something goes wrong.

•

The Appendixes give in-depth information on topics covered in the
manual. Appendix A contains RRD compact disk drive instructions,
Appendix B contains TF/TK tape drive instructions, Appendix C lists
the device type code assignments, Appendix D describes VAXBI options
and adapters, Appendix E gives detailed information on the EVUCA
program, Appendix F lists control flags for booting, Appendix G
summarizes the console commands, Appendix H lists console error

messages for Model 400 and higher systems. Appendix I has console
error messages for Model 300 systems, and Appendix J contains boot
status and error messages for Model 500 and 600 systems.
•

A Glossary and Index provide additional reference support.

Conventions Used in This Document
The icons shown below are used in illustrations for designating part
placement in VAX 6000 series systems. A shaded area in the icon shows
the location of the component or part being discussed.

FRONT

REAR

VAX 6000 Series Documents
There are two sets of documentation: manuals that apply to all VAX 6000
series systems and manuals that are specific to one VAX 6000 model.
Table 1 lists the manuals in the VAX 6000 series documentation set.

Table 1: VAX 6000 Series Documentation
Title

Order Number

Operation
VAX 6000 Series Owner’s Manual

EK–600EB–OM

VAX 6000 Series Vector Processor Owner’s Manual

EK–60VAA–OM

VAX 6000 Vector Processor Programmer’s Guide

EK–60VAA–PG

xii

Table 1 (Cont.): VAX 6000 Series Documentation
Title

Order Number

Service and Installation
VAX 6000 Platform Technical User’s Guide

EK–600EA–TM

VAX 6000 Series Installation Guide

EK–600EB–IN

VAX 6000 Installationsanleitung

EK–600GB–IN

VAX 6000 Guide d’installation

EK–600FB–IN

VAX 6000 Guia de instalacion

EK–600SB–IN

VAX 6000 Platform Service Manual

EK–600EA–MG

Options and Upgrades
VAX 6000: XMI Conversion Manual

EK–650EB–UP

VAX 6000: Installing MS65A Memories

EK–MS65A–UP

VAX 6000: Installing the H7236-A Battery Backup Option

EK–60BBA–IN

VAX 6000: Installing the FV64A Vector Option

EK–60VEA–IN

VAX 6000: Installing the VAXBI Option

EK–60BIA–IN

Manuals specific to models are listed in Table 2.

Table 2: VAX 6000 Model Level Documentation
Title

Order Number

Model 600
VAX 6000 Model 600 Mini-Reference

EK–660EA–HR

VAX 6000 Model 600 Service Manual

EK–660EA–MG

VAX 6000 Model 600 System Technical User’s Guide

EK–660EA–TM

VAX 6000: Installing Model 600 Processors

EK–660EA–UP

xiii

Table 2 (Cont.): VAX 6000 Model Level Documentation
Title

Order Number

Model 500
VAX 6000 Model 500 Mini-Reference

EK–650EA–HR

VAX 6000 Model 500 Service Manual

EK–650EA–MG

VAX 6000 Model 500 System Technical User’s Guide

EK–650EA–TM

VAX 6000: Installing Model 500 Processors

EK–KA65A–UP

Models 200/300/400
VAX 6000 Model 300 and 400 Service Manual

EK–624EA–MG

VAX 6000: Installing Model 200/300/400 Processors

EK–6234A–UP

Associated Documents
Table 3 lists other documents that you may find useful.

Table 3: Associated Documents
Title

Order Number

System Hardware Options
VAXBI Expander Cabinet Installation Guide

EK–VBIEA–IN

VAXBI Options Handbook

EB–32255–46

System I/O Options
CIBCA User Guide

EK–CIBCA–UG

CIXCD Interface User Guide

EK–CIXCD–UG

DEC LANcontroller 200 Installation Guide

EK–DEBNI–IN

DEC LANcontroller 400 Installation Guide

EK–DEMNA–IN

DSSI VAXcluster Installation Manual

EK–DVCLU–IN

InfoServer Installation Guide

EK–DIS1K–IN

KDB50 Disk Controller User’s Guide

EK–KDB50–UG

xiv

Table 3 (Cont.): Associated Documents
Title

Order Number

System I/O Options
KDM70 Controller User Guide

EK–KDM70–UG

KFMSA Module Installation and User Manual

EK–KFMSA–IM

KFMSA Module Service Guide

EK–KFMSA–SV

RRD40 Disc Drive Owner’s Manual

EK–RRD40–OM

RA90/RA92 Disk Drive User Guide

EK–ORA90–UG

RF31/RF72 Integrated Storage Element Installation Manual for
BA200–Series Enclosures

EK–RF72D–IM

RF31/RF72 Integrated Storage Element User Guide

EK–RF72D–UF

RF31/RF72 Integrated Storage Element Service Guide

EK–RF72D–SV

SA70 Enclosure User Guide

EK–SA70E–UG

SF200 Storage Array Installation Guide

EK–SF200–IG

SF72 Storage Enclosure and SF200 Storage Array Cabinet
Service Guide

EK–SF72S–SG

TF85 Cartridge Tape Subsystem Owner’s Manual

EK–TF85–OM

TF857 Magazine Tape Subsystem Service Manual

EK–TF857–OM

VAX 6000 SF2xx Embedded Storage Installation Guide

EK–EMBED–IN

Operating System Manuals
Guide to Maintaining a VMS System

AA–LA34B–TE

Guide to Setting Up a VMS System

AA–LA25A–TE

Introduction to VMS System Management

AA–LA24A–TE

ULTRIX–32 Guide to System Exercisers

AA–ME96B–TE

VMS Networking Manual

AA–LA48A–TE

VMS System Manager’s Manual

AA–LA00B–TE

VMS Upgrade and Installation Supplement: VAX 6000 Series

AA–LB36C–TE

Table 3 (Cont.): Associated Documents
Title

Order Number

VAXclusters and Networking
DECbridge 500 Installation Guide

EK–DEFEB–IN

DEMFA Installation Guide ??

EK–?????–??

Fiber Distributed Data Interface Description

EK–DFSLD–SD

Guidelines for VAXcluster System Configurations

EK–VAXCS–CG

H4000 Digital Ethernet Transceiver Installation Manual

EK–H4000–IN

HSC Installation Manual

EK–HSCMN–IN

VAXcluster Principles

EK–VAXCP–TM

VAX 6000/VAX 4000—300 SF200 System Manual

TBD

VMS VAXcluster Manual

AA–LA27B–TE

Peripherals
Installing and Using the VT420 Video Terminal

EK–VT420–UG

RV20 Optical Disk Owner’s Manual

EK–ORV20–OM

SC008 Star Coupler User’s Guide

EK–SC008–UG

TA78 Magnetic Tape Drive User’s Guide

EK–OTA78–UG

TA90 Magnetic Tape Subsystem Owner’s Manual

EK–OTA90–OM

TK70 Streaming Tape Drive Owner’s Manual

EK–OTK70–OM

TU81/TA81 and TU/81 PLUS Subsystem User’s Guide

EK–TUA81–UG

VAX Manuals
VAX Architecture Reference Manual

EY–3459E–DP

VAX Systems Hardware Handbook — VAXBI Systems

EB–31692–46

VAX Vector Processing Handbook

EC–H0739–46

xvi

Chapter 1

The VAX 6000 Series System
The VAX 6000 series computer system is designed for growth and can
be configured for many different applications. Like other VAX systems,
the VAX 6000 series system can support many users in a time-sharing
environment. This system does the following:
•

Supports a full range of VAX applications and operating systems

•

Functions as a standalone system, a member of a VAXcluster, a boot
node of a local area VAXcluster, or as a VAX file server for workstations

•

Allows for expansion of processors, memory, and I/O

•

Implements symmetric multiprocessing where all processors have equal
access to memory

•

Supports vector processors on Model 400 and Model 500 systems

•

Uses a high-bandwidth system bus designed for multiprocessing

•

Performs automatic self-test on power-up, reset, reboot, or system
initialization

•

Supports I/O devices on the VAXBI bus and provides access to the
VMEbus

This chapter describes the system packages and introduces the location of
components in the cabinet. Sections include:
•

System characteristics

•

System architecture

•

Sample system

•

System front view

•

System rear view

•

Supported adapters

The VAX 6000 Series System 1–1

1.1 System Characteristics
All VAX 6000 series systems share the same characteristics
as shown in the tables. Figure 1–1 shows a system footprint.

SYSTEM
CABINET

DISK
CABINET

104 CM (41.5 IN)

154 CM (60.5 IN)

Figure 1–1: Sample System Footprint

56 CM (22 IN)

78 CM (30.5 IN)

53 CM (21 IN)*

TAPE
CABINET

REAR
CLEARANCE
1 M (39 IN)

TAPE
CABINET

SYSTEM
CABINET

DISK
CABINET

WIDTH*
1.9 M (74 IN)

.9 M
(36 IN)

DEPTH
2.9 M (114 IN)

FRONT
CLEARANCE
1 M (39 IN)

* The SF200 storage array cabinet is 5 cm (2 in) wider.
msb-0119-C-91

1–2 VAX 6000 Series Owner’s Manual

The values listed in Table 1–1 relate to the system cabinet only. In-cabinet
storage will increase electrical requirements.

Table 1–1: Electrical Characteristics
Electrical1

Without VAXBI

With VAXBI

2.5 KVA

3.5 KVA

7.0 A (208 V)

9.7 A (208 V)

3.5 A (416 V)
3.8 A (380 V)

4.8 A (416 V)
5.3 A (380 V)

3-phase 208 V RMS

3-phase 380/416 V RMS

AC power consumption
(max)
AC current (nom)

Voltage input

Frequency tolerance

47–63 Hz

Surge current

60 A

1 These values assume a base system with no optional disks or battery backup unit.

Table 1–2: Environmental Characteristics
Environmental
Heat dissipation (max)
Operating temperature

Operating humidity

Altitude

5570 Btu/hr
TF/TK not in use

10o to 40o C (50o to 104o F) 1

TF/TK in use

15o to 32o C (59o to 90o F)

TF/TK not in use

10 to 90% relative humidity

TF/TK in use

20 to 80% relative humidity

Operating

0 to 2.4 km (0 to 8000 ft)

Nonoperational

0 to 9.1 km (0 to 30,000 ft)

1 Model 600 range: 15o to 32o C (59o to 90o F)

The VAX 6000 Series System 1–3

1.2 System Architecture
The high-speed XMI bus is used to interconnect processors,
memory modules, and I/O adapters.

Figure 1–2: System Architecture

PROCESSORS

MEMORY
XMI

DEMNA

DEMFA

CIXCD

DWMBB

KFMSA

KDM70
DWMVA
msb-0310A-91

1–4 VAX 6000 Series Owner’s Manual

The XMI is the 64-bit system bus that interconnects the processors, memory
modules, and I/O adapters.
The XMI bus uses the concept of a node. A node is a single functional unit
that consists of one or more modules. The XMI has three types of nodes:
processor nodes, memory nodes, and I/O adapters.
A processor node is a single-board scalar processor or a scalar/vector
processor pair. Multiprocessing is supported on VAX 6000 systems. Up
to six scalar processors can be used in most systems.1 Models 400 and
500 support vector processing with multiple scalar/vector processor pairs.
Symmetric multiprocessing is supported, allowing a program to execute on
any processor.
In a multiprocessing system one scalar processor becomes the boot processor
during power-up, and that boot processor loads the operating system and
handles communication with the operator console. The other processors
become secondary processors and receive system information from the boot
processor (see Section 4.5).
A memory node is one memory module. Memory is a global resource
equally accessible by all processors on the XMI. A memory module can have
32, 64, or 128 Mbytes of memory and associated ECC and control logic. The
memories are automatically interleaved. An optional battery backup unit
protects memory in case of power failure. The system supports up to eight
memories.
I/O adapters are installed on the XMI bus (see Section 1.6). If your system
has a VAXBI, the DWMBB adapter is used to connect VAXBI I/O adapters
to the XMI bus. See Appendix D for information on VAXBI I/O adapters.
The DWMVA adapter provides an interface to the VMEbus.

Model 200 supports multiprocessing with up to four scalar processors.

The VAX 6000 Series System 1–5

1.3 Sample System
Figure 1–3 shows a sample VAX 6000 system. The system
cabinet can have an optional console load device and
optional in-cabinet disk drives. The system includes a
console terminal and printer, an accessories kit, and a
documentation set, which includes this manual. The system
may have additional storage devices and may be a member
of a VAXcluster.

Figure 1–3: Sample System

SYSTEM
CABINET

OPTIONAL
STORAGE
DEVICE

VT400 SERIES
TERMINAL
LA75
PRINTER

MANUALS

1–6 VAX 6000 Series Owner’s Manual

msb-0251A-91

Table 1–3: System Components
Component

Function

System cabinet

Houses system components and optional storage

Console load device

Software distribution; stores and transfers data

Console terminal

Manages system and its resources

Console printer

Provides hardcopy of console transactions

Documentation

See the Preface for a full list of documentation
related to VAX 6000 series systems

Storage cabinet

Provides additional storage capacity

Your Digital customer service engineer has installed your system and
verified that it is running properly. Before you turn on the system,
familiarize yourself with its components:
•

The system cabinet houses the XMI card cage (which contains the
processors, memories, and I/O adapters) and the control panel with
status indicators. Optional hardware in the cabinet includes a console
load device, a VAXBI backplane, and disk drives.

•

The console load device is used for installing operating systems,
software, and some diagnostics. The console load device can be a tape
drive, either in the cabinet or in the SF200 storage array, or it can be
an Ethernet-based compact disk server.

•

A storage cabinet provides local storage and archiving capability.

•

The console terminal is used for booting and for system management
operations.

•

A system documentation kit

The VAX 6000 Series System 1–7

1.4 System Front View
The control panel and optional console load device and
disk control panel are on the front of the system cabinet,
accessible with the doors closed. With the front door open,
Digital customer service engineers can access the power
regulators, the XMI card cage and optional VAXBI card
cages, the cooling system, and the optional battery backup
unit.

Figure 1–4: System Front View

CONSOLE LOAD
DEVICE
CONTROL PANEL
VAXBI CARD
CAGES

XMI POWER REGULATORS
VAXBI POWER REGULATORS

XMI CARD CAGE

COOLING SYSTEM

POWER AND
LOGIC BOX

BATTERY BACKUP UNIT
OR DISKS

TRANSFORMER
(50 Hz SYSTEMS )

* OPTIONAL

1–8 VAX 6000 Series Owner’s Manual

DISKS

*
msb-0311A-91

WARNING: The inside of the system cabinet is not designed to be accessed
by the customer. The information in this chapter is for your information
only. The cabinet doors are to be opened only by Digital customer service
engineers.
These components are visible from the inside front of the cabinet (see
Figure 1–4 for their location):
•

Control panel

•

XMI power regulators

•

XMI card cage

•

Cooling system
One of the two blowers is visible from the front of the cabinet.

•

Power and logic box

•

Transformer (on 50 Hz systems only)

Optional components:
•

Console load device

•

VAXBI power regulators

•

Two VAXBI card cages configured as one 12-slot channel

•

Battery backup unit

•

Disks

The VAX 6000 Series System 1–9

1.5 System Rear View
With the rear door open, Digital customer service engineers
can access the power sequencer module (XTC); the power
regulators; the I/O bulkhead space behind the card cages;
Ethernet and console terminal connectors; cooling system;
power and logic box; battery backup unit and disks, if
present; and the AC power controller.

Figure 1–5: System Rear View

XTC POWER
SEQUENCER MODULE
XMI POWER
REGULATORS

XMI
CARD CAGE

COOLING
SYSTEM
BATTERY
BACKUP UNIT
OR DISKS *
DISKS *

* OPTIONAL

1–10 VAX 6000 Series Owner’s Manual

VAXBI POWER
REGULATORS *
VAXBI
CARD CAGES *

ETHERNET AND
CONSOLE TERMINAL
CONNECTORS

POWER AND
LOGIC BOX
AC POWER
CONTROLLER
msb-0312A-91

Power sequencer module (XTC) located on the back of the system control
assembly

•

XMI power regulators

•

I/O bulkhead space
The panel covering the XMI and VAXBI areas is the I/O bulkhead panel
and provides space for additional I/O connections.

•

XMI backplane and cables

•

Ethernet and console terminal connectors

•

Cooling system, with open grid over a blower

•

Power and logic box

•

AC power controller

Optional components:
VAXBI power regulators
VAXBI backplane and cables
Battery backup unit
Disks

The VAX 6000 Series System 1–11

1.6 Supported Adapters
VAX 6000 systems provide interfaces to other buses and to
the Ethernet. Systems can be clustered and storage can
be added and shared among systems. The system supports
the following adapters: CIXCD, DEC LANcontroller 400
(DEMNA), DEMFA, DWMBB, DWMVA, KDM70, and KFMSA.

Figure 1–6: Adapters

BUS
CONTROLLERS

NETWORK
CONTROLLERS

CIXCD

KFMSA

DWMBB

DWMVA

DSSI

VAXBI

VMEbus

DEMNA

DEMFA

MULTIPLE-HOST
CLUSTER ADAPTERS
CIXCD

KFMSA

DSSI

LOCAL TAPE/DISK CONTROL
KFMSA

KDM70

DWMBB

DWMVA

TF tapes
RF disks

TA tapes
RA disks

To TK/TU tapes
& RA disks
on VAXBI

To VMEbus
devices

1–12 VAX 6000 Series Owner’s Manual

msb-0759-91

Table 1–4 describes the adapters supported by the system. Note that some
adapters require more than one slot on the XMI.

Table 1–4: Adapters
Adapter

XMI
Slots

CIXCD

CI port interface;
pler.

DEMFA

FDDI (fiber optic) port interface; connects a system to a local area network.

DEMNA

Ethernet port interface; connects a system to a local area network.

DWMBB

XMI-to-VAXBI interface, a two-module set.
The DWMBB/
A is in the XMI card cage; the DWMBB/B is installed in the VAXBI
card cage.1

DWMVA

XMI-to-VMEbus interface, a two-module set.
The DWMVA/
A is in the XMI card cage; the DWMVA/B is installed in a VMEbus expansion cabinet.

KDM70

Disk adapter; enables connection to RA disk drives.

KFMSA

DSSI adapter; enables connection to TF tape drives and to RF disk
drives.

Function
connects the system to a Star Cou-

1 See Appendix D for information on VAXBI adapters and options.

For more information on adapters, see Digital’s Systems and Options
Catalog or the VAX 6000 Platform Service Manual.
Appendix C lists the device type codes for XMI adapters, and Appendix D
lists the device type codes for VAXBI adapters.

The VAX 6000 Series System 1–13

1–14 VAX 6000 Series Owner’s Manual

Chapter 2

System Components
This chapter describes system components, noting their locations and
functions. Sections include:
•

Console load devices
Ethernet-based compact disk server
Tape drive

•

Power system

•

XMI card cage

•

I/O connections

•

Cooling system

•

Options

System Components 2–1

2.1 Console Load Devices
Figure 2–1 shows VAX 6000 console load devices and their
adapters.

Figure 2–1: Console Load Devices

TK/TF TAPE

CD-ROM
VAXBI

TF85 TF857

CD
SERVER

TK70

DEBNI

DWMBB

ETHERNET
DSSI

TBK70

VAXBI

DECbridge
500
FDDI

KFMSA

DWMBB

XMI

DEMNA

DEMFA

XMI
msb-0317A-91

2–2 VAX 6000 Series Owner’s Manual

The console load device is used for:
•

Installing or updating software

•

Loading diagnostics

•

Loading the standalone backup program

•

Interchanging user data

Any of the following can serve as the console load device:
•

Ethernet-based compact disk (CD) server

•

TF or TK tape drive in the system cabinet

•

TF magazine tape subsystem in a storage cabinet

System Components 2–3

2.1.1 Ethernet-Based Compact Disk Server
The InfoServer is a console load device. During system
installation the InfoServer can be used to boot the
VAX Diagnostic Supervisor and standalone backup; it is
not needed to load or initialize the system following
installation.

Figure 2–2: Ethernet-Based Compact Disk Server

InfoServer 100

msb-0637B-91

2–4 VAX 6000 Series Owner’s Manual

The InfoServer, an Ethernet-based compact disk (CD) server, is part of a
local area network. The CD server functions as a read-only storage device
for any system on the Ethernet. The CD server is used to access CD-ROMs
for software installation, diagnostics, and on-line documentation.
The DEMNA adapter1 and DEMFA adapter provide an interface to the
Ethernet-based CD server. Both adapters are in the XMI card cage.
However, as shown in Figure 2–3, the DEMFA provides access to the FDDI
(Fiber Distributed Data Interface) network and requires a DECbridge 500
for connection to the Ethernet.
Section 4.7 describes how to boot VMS over the Ethernet using the CD
server as the console load device. For more information on how to use the
CD server, see the InfoServer Installation Guide.

Figure 2–3: Accessing the Ethernet-Based CD Server
XMI

DEMNA

CD SERVER
ETHERNET

XMI

DEMFA

CD SERVER
FDDI
DECbridge 500

ETHERNET

msb-0480A-91

The DEBNI or DEBNA adapter can also be used as an interface to the Ethernet-based
compact disk server.

System Components 2–5

2.1.2 In-Cabinet Tape Drive
The system cabinet can have a TF or TK tape drive at the
upper left of the cabinet. Either tape drive serves as a
console load device.

U
nl

W
r
Pr i t e
ot
ec
Ta ted
pe
in
U
U
se
s
Ce
le
Ta an
pe ing
O
pe
r
H ate
an
dl
e

Figure 2–4: TF85 Tape Drive

Lo
To
R

W
O
Pr To
H Clo Ins H Op Wa
em Ha pe a
es
an s
e a e
U
s
n
ov ndl n t it
dl e t rt T ndl n t it
Bu loa
e h
e hi
e
ap e his
is
s
Ta
tto d
Li
e
gh
pe
n
t

Li
g

FRONT

msb-0766-91

2–6 VAX 6000 Series Owner’s Manual

Three tape drives serve as console load devices. The operation of the TK70
tape drive is similar to that of the TF85 tape drive (see Appendix B for
information on how to use the tape drive). The TF857 tape drive also
serves as a console load device. The TF857 is a magazine tape subsystem
in the SF2xx storage array. Both the TF85 and TF857 tape drives are DSSI
devices and require the KFMSA adapter.
The TK70 tape drive requires the VAXBI option and is controlled by the
TBK70 adapter, which resides in the VAXBI card cage.
For detailed information on how to use the tape drives, see the books listed
in the Associated Documents section of the Preface.

System Components 2–7

2.2 Power System
The power system consists of an AC power controller with
circuit breaker, the power and logic box, three power
regulators, and an optional battery backup unit.

Figure 2–5: Power System (Rear View)

POWER
REGULATORS

POWER AND
LOGIC UNIT
BATTERY BACKUP
UNIT (OPTIONAL)

AC POWER
CONTROLLER
msb-0308A-91

You can see most of the power system from the rear of the cabinet. The
AC power controller with circuit breaker (see Section 3.6) is in the lower
right corner. The power and logic box is just above the AC power controller.
Across the top of the cabinet are the power regulators.
Table 2–1 gives the input voltage for the power controller. On the back of
the power controller are two fuse-protected power outlets. Devices attached
at these outlets are powered down only when the AC power controller circuit
breaker is set to Off.

2–8 VAX 6000 Series Owner’s Manual

The XMI power supply is made up of three power regulators.1 The
power supply provides sufficient power for any combination of modules (see
Table 2–2.)

Table 2–1: AC Power Controller Input Voltage
Nominal Input
Voltages

Model No.

Phase

H405-E

208 V

H405-F

380 V

416 V

Table 2–2: Power Supply Available
DC Voltage

Available XMI Current

+5V

124.0 A

+3.3V

80.0 A

+12V

4.0 A

–12V

2.5 A

–5.2V

20.0 A

–2V

7.0 A

The optional battery backup unit (BBU), if present, is located near the
bottom of the cabinet. This unit supplies power to sustain memory for up
to 10 minutes following power interruption to system memory. The unit
also provides 1 second of ride-through capability. The BBU has its own fan,
which operates only when power is being supplied by the BBU. The system
control panel indicates the status of the battery backup unit.

Two additional power regulators are required if the system includes the optional VAXBI.

System Components 2–9

2.3 XMI Card Cage
The 14-slot XMI card cage houses processors, memories, and
adapters. The XMI high-speed system bus interconnects the
modules; it has a maximum bandwidth of 100 Mbytes per
second and supports up to six processors.

Figure 2–6: XMI Card Cage

XMI CARD CAGE

FRONT

Processors

Memory

XMI

DEMNA

DEMFA

CIXCD

KFMSA

DWMBB/A

KDM70
DWMVA/A
msb-0316C-91

2–10 VAX 6000 Series Owner’s Manual

The system bus, the XMI, allows several transactions to occur
simultaneously, making efficient use of the bus bandwidth. The bus
includes the XMI backplane, the electrical environment of the bus, the
protocol that nodes use on the bus, and the logic to implement this protocol.
The 14-slot XMI card cage is located in the upper third of the cabinet on
the right side, as viewed from the front of the cabinet. A clear latched
door protects the components housed in the card cage and helps to direct
the airflow over the modules. Indicator lights on the XMI modules can be
viewed through this clear front door. The protective door must be closed
for operation, as it controls the power supply to the card cage.
Each slot of the XMI card cage is hardwired to a 4-bit node ID code that
corresponds to the physical slot number in the card cage. The node ID
number of the module is its slot position. The slots are numbered 1 through
E (hexadecimal) from right to left, as you view the card cage from the front
of the cabinet.
For information on XMI card cage configuration rules and module indicator
lights, see the VAX 6000 Platform Service Manual. The VAX 6000 Platform
Technical User’s Guide gives in-depth information on the operation of the
system bus.

System Components 2–11

2.4 I/O Connections
I/O connections are installed on the bulkhead connections
tray and the I/O panel. The I/O tray is located in the rear of
the cabinet, above the cooling system and below the power
regulators, and covers the XMI backplane. The I/O panel is
just below the right-hand side of the I/O tray and houses the
Ethernet and console terminal ports.

Figure 2–7: Console and Terminal Connectors

REAR
I/O
BULKHEAD
TRAY

I/O PANEL

CONSOLE
TERMINAL
PORT

ETHERNET
PORT
msb-0143A-91

2–12 VAX 6000 Series Owner’s Manual

The I/O bulkhead connections tray is located in the rear of the cabinet,
above the cooling system and I/O panel, and below the power regulators.
It is hinged at the bottom, and folds out and down for servicing the card
cages and backplanes. The I/O panel is on the right side below the tray.
The I/O tray and panel have 30 panel units designed to accommodate a
variety of I/O connectors.
The Ethernet and console terminal connectors are at the bottom of the I/O
panel. The Ethernet port is a 15-pin receptacle located on the bottom right,
and the console terminal port is the 25-pin receptacle on the left. These
connectors are labeled with international symbols, as shown in Figure 2–7.

System Components 2–13

2.5 Cooling System
The cooling system consists of a fan, two blower units, and
an airflow path through the XMI card cage (and VAXBI card
cages, if present).

Figure 2–8: Airflow Pattern

POWER
REGULATORS

CARD CAGES

BLOWERS

FRONT

EXTERNAL
FRONT VIEW

REAR

INTERNAL
SIDE VIEW
msb-0008-89

2–14 VAX 6000 Series Owner’s Manual

The cooling system is designed to keep system components at an optimal
operating temperature. It is important to keep the front and rear doors
free of obstructions, leaving a clear space of 39.4 inches (1 meter) from the
cabinet to maximize air intake.
The blowers, located in the lower half of the cabinet, draw air in through the
doors and push air up through the card cages. The air is directed through a
duct to cool the console load device if there are no VAXBI card cages in the
system. The airflow continues through the top of the card cages, through
the power regulators, and out the top of the front and rear doors. A fan
cools the power and logic box.
The system has safety detectors for the cooling system: an airflow sensor
and a thermostat are installed above the power regulators in the top of
the cabinet. Extreme conditions activate these detectors. Under extreme
temperatures, the thermostat shuts off all output power (including power
at the two unswitched outlets) at the AC power controller. In this condition
the battery backup unit is disabled and will not provide power. If the
airflow to your system is seriously blocked for an extended period of time,
the airflow sensor shuts off the power supply. If either condition occurs,
call your Digital customer service engineer.

System Components 2–15

2.6 Options
Other system options in addition to the console load device
include the VAXBI card cages and power regulators, battery
backup unit, and in-cabinet disks.

Figure 2–9: System Options

VAXBI POWER
REGULATORS

VAXBI CARD
CAGES

BATTERY BACKUP UNIT
OR DISKS
DISKS

msb-0398A-91

2–16 VAX 6000 Series Owner’s Manual

Options include the VAXBI I/O interface, battery backup unit, and incabinet disks. The VAXBI card cages are located in the upper third of
the cabinet on the left side, as viewed from the front of the cabinet. The
disks and battery backup unit are located beneath the blowers and are rackmounted. The first of these two options to be installed is placed adjacent
to the AC power controller.
VAXBI Card Cages and Power Regulators
The optional VAXBI I/O interface is a one-channel bus housed in two
6-slot VAXBI card cages. Two power regulators supply power to the
VAXBI backplane. A clear latched door protects the components housed
in the VAXBI card cages and helps to direct the airflow over the modules.
Indicator lights on the modules can be viewed through this clear front door.
The protective door must be closed for normal operation, as it controls the
power supply to the card cages.
Additional VAXBI card cages can be added to a system by installing a
VAXBI expander cabinet (see Appendix D). See the VAX 6000 Platform
Service Manual for more information on the VAXBI card cages.
Battery Backup Unit
The battery backup unit supplies power to sustain the system for up to 10
minutes following a power interruption. Ride-through capability for up to
1 second is provided. The system control panel indicates the status of the
battery backup unit.
Disks
The system cabinet provides space for two SA7x building blocks (8 RA7x
drives), two RA92 disk drives, or two SF7x arrays (8 RF7x drives), or some
combination. The disk control panel is accessed through an opening in the
cabinet front door.

NOTE: Installation of a battery backup unit allows only one disk enclosure
to be installed in the system cabinet.

System Components 2–17

Chapter 3

Controls and Indicators
This chapter introduces system controls and indicators. Sections include:
•

Control panel

•

Upper key switch

•

Lower key switch

•

Restart button

•

Status indicator lights

•

Circuit breaker

Controls and Indicators 3–1

3.1 Control Panel
The control panel, at the upper left of the cabinet front,
contains the upper and lower key switches, status lights,
and a Restart button. The upper and lower switches are
operated by a key.

Figure 3–1: International and English Control Panels

FRONT
EEPROM
2
1

0
Standby

Run

Enable

Battery

Secure

Fault

Update
Halt

KEY

Auto Start

Restart

msb-0037A-91

3–2 VAX 6000 Series Owner’s Manual

The control panel is at the upper left of the cabinet. You use the control
panel when powering on the machine or changing the operating mode of
your system.
The upper and lower switches are operated by a key. Two keys are shipped
with each system. The key has a toothed hollow barrel and fits into the
slotted circle of each switch. Each key works on both switches.
Labels for the control panel’s upper and lower key switches can be in
English or in international symbols. Table 3–1 gives the relationship
between the international symbols and English equivalents. References
to the control panel in the remainder of this manual refer to the English
labels.

Table 3–1: Control Panel Symbols

Location

English

International Symbol

Upper key switch

O (Off)

Standby
Enable
Secure
Lower key switch

Status indicators

Update

EEPROM

Halt

Auto Start

Run
Battery
Fault

Restart button

Restart

(None, blank)
msb-0575A-91

Controls and Indicators 3–3

3.2 Upper Key Switch
The control panel’s upper key switch regulates power going
into the system and determines use of the console terminal.
The four switch positions are Off, Standby, Enable, and
Secure.

Figure 3–2: Upper Key Switch (Enable Position)

0
Standby
Enable
FRONT

Secure

msb-0170A-91

3–4 VAX 6000 Series Owner’s Manual

Table 3–2: Upper Key Switch
Position

Effect

Light Color

O (Off)

Removes all power, except to the battery backup
charger and optional storage.

No light

Standby

Supplies power to XMI backplane, blowers, and incabinet console load device.

Red

Enable

Supplies power to whole system; console terminal is enabled. Used for console mode or restart, and to start
self-test.

Yellow

Secure
(Normal Position)

Prevents entry to console mode; position used while machine is executing programs. Disables Restart button.
When switch at Secure, the system performs an automatic restart, regardless of the setting of the lower key switch.

Green

The upper key switch has four positions: Off, Standby, Enable, and Secure.
You change the position of the upper key switch by inserting and turning
a key. A light to the right of each key position lights to show what mode is
in operation. When the switch is set to Off, no lights are lit. Each position
modifies power to the system as follows:
•

Off removes all power from the system, disabling the battery backup
unit’s output. This position is a total off, except for power to the battery
charger and optional storage. To ensure total absence of power in
the machine, pull the circuit breaker and unplug the machine. See
Section 3.6.

•

Standby powers the XMI backplane, blowers, and in-cabinet console
load device.

•

Enable supplies power to the entire system. While the upper switch is
in the Enable position, you can use the console (see Chapter 5) or the
Restart button (see Section 3.4). Also, when you move the upper switch
from Standby to Enable, the system runs self-test. If the power goes off
with the switch in the Enable position, the operation of the system is
controlled by the position of the lower key switch. Figure 3–2 shows the
upper key switch with the key in the Enable position and the Enable
light lit.

•

Secure prevents interruptions to program execution. When the switch
is in the Secure position, the console terminal can only be used as a
user terminal (in program mode). A CTRL/P does not cause a switch
to console mode. Secure also disables the Restart button. If the power
goes off with the switch in the Secure position, the system may reboot
if it has a battery backup unit or if power is restored.

Controls and Indicators 3–5

3.3 Lower Key Switch
The control panel’s lower key switch controls system
operation. The three positions for this switch are Update,
Halt, and Auto Start.

Figure 3–3: Lower Key Switch (Update Position)

FRONT

Update
Halt
Auto Start

msb-0171A-91

3–6 VAX 6000 Series Owner’s Manual

When the upper key switch is in the Secure position, the lower key switch
has the effect of Auto Start, regardless of its setting. (See Section 3.2.)

Table 3–3: Lower Key Switch
Position

Effect

Light Color

Update

Enables writing to CPUs and adapters. Halts boot processor in console mode on power-up or when Restart
button is pressed. Used for updating parameters stored
in EEPROMs (upper key switch must be set to Enable). Prevents an auto restart.

Red

Halt

Prevents an auto restart if a failure or transient power outage occurs.

Yellow

Auto Start
(Normal Position)

Allows restart or reboot.
tion of the system.

Green

Used for normal opera-

The lower key switch has three positions: Update, Halt, and Auto Start.
A light to the right of each key position lights to indicate which mode is
engaged.
Each position engages the primary processor in a different way.
•

Update readies the CPU for parameter changes to the EEPROM which
are entered from the console terminal. You must have the switch in the
Update position to use some console commands: UPDATE and most
SET commands (see Section 5.18.1 through Section 5.18.5). (The upper
key switch must be set to Enable.) Digital customer service engineers
and self-maintenance customers use Update for updates to the console,
self-test, and ROM diagnostics programs. See also Section 5.24. When
the key is in the Update position, an automatic restart is inhibited.
Figure 3–3 shows the lower key switch with the key in the Update
position and the Update light lit.

•

Halt inhibits automatic restart when a failure or transient power
outage happens. It is the opposite of Auto Start. On power-up, the
system halts in console mode, and you can issue a BOOT command
(see Section 5.6).

•

Auto Start is the key position for normal operation. The key must be in
this position for automatic rebooting or restarting the system following
a power failure.

Controls and Indicators 3–7

3.4 Restart Button
The Restart button begins self-test, reboot, or both,
depending on the position of the upper and lower key
switches.

Figure 3–4: Restart Button

FRONT

Enable

Auto Start

Restart

msb-0172A-91

3–8 VAX 6000 Series Owner’s Manual

The upper key switch controls the effect of the Restart button. When the
upper key switch is in the Enable position, the Restart button is operative.
If the upper key switch is not in the Enable position, the Restart button is
ignored.

Table 3–4: Restart Button
Upper Key Switch

Lower Key Switch

Restart Button Function

Enable

Update or Halt

Runs self-test, then halts.

Enable

Auto Start

Runs self-test and attempts a reboot. If the reboot fails, control returns to the console.

Standby
or Secure

Any position

Does not function.

When you press the Restart button, the system runs self-test. For the
Restart button to reboot the operating system, the upper key switch must be
set to Enable and the lower key switch must be set to Auto Start. Figure 3–4
shows the control panel with upper and lower key switches in position for
using the Restart button to reboot. If the system fails self-test, the processor
does not reboot the operating system.

Controls and Indicators 3–9

3.5 Status Indicator Lights
The control panel has three status indicator lights: Run,
Battery, and Fault. These lights indicate the operating
status of the system.

Figure 3–5: Control Panel Status Indicator Lights

0
Run
FRONT

Battery
Fault

msb-0173A-91

3–10 VAX 6000 Series Owner’s Manual

Three status indicator lights on the control panel show the state of system
execution (Run), the presence of a battery backup unit (Battery), and
hardware errors (Fault).
Figure 3–5 shows a system that is in operation, with a fully charged battery
backup unit installed. Table 3–5 describes the conditions indicated by the
status indicator lights.

Table 3–5: Control Panel Status Indicator Lights
Light

Color

State

Meaning

Run

Green

System is executing operating system instructions on
at least one processor.

Off

System is in console mode, is set to Standby, or is
turned off.

Battery backup unit is charged to 98% of full capacity or BBU is supplying power to the load.

Flashing
1 x/sec

Battery backup unit is charging.

Flashing
10 x/sec

Battery backup unit requires service.

Off

System does not have a battery backup unit.

Self-test is in progress. If light does not turn off, system has a hardware fault. See Chapter 6 for selftest information.

Off

Self-test has completed, or the system is turned off.

Battery

Fault

Green

Red

Controls and Indicators 3–11

3.6 Circuit Breaker
The circuit breaker is on the AC power controller, which is
at the bottom right corner at the back of the cabinet.

Figure 3–6: Circuit Breaker and the AC Power Controller

AC OUTLETS
(UNSWITCHED)

REAR

CIRCUIT
BREAKER
OUTLET
FUSES

DEC POWER
CONTROL BUS

AC POWER TEST
RECEPTACLE FOR
POWER ANALYZERS

AC 3-PHASE
INPUT

AC POWER
TEST
RECEPTACLE
FUSES

msb-0318-91

3–12 VAX 6000 Series Owner’s Manual

Figure 3–6 shows the AC power controller, which is at the rear of the
cabinet.
Circuit Breaker
The circuit breaker controls power to the entire system, including the power
regulators, blowers, and in-cabinet options. Current overload causes the
circuit breaker to move automatically to the Off position, so that power to
the system is turned off.
For normal operation, the circuit breaker must be in the On position, which
is fully pressed in. To trip the circuit breaker, pull it out toward you, away
from the machine, until the circuit breaker handle is flush with the AC
power controller.
If the temperature of the system exceeds 75o C (167o F), the "contactor" in
the AC power controller is opened and the system powers down.
AC Power Test Receptacle Fuses
These three fuses are used as a protective measure during power testing
at the AC power test receptacle.
AC Outlets (Unswitched)
The two unswitched outlets on the AC power controller are used to power
in-cabinet disk drives or a battery backup unit. The outlet fuses are to the
left of the outlets.
DEC Power Control Bus
Two DEC power control bus connectors are located on the AC power
controller. The power control bus provides central power-up and powerdown capability by connecting the power controllers in your system, VAXBI
expander, and storage cabinets.
AC Power Test Receptacle
This covered receptacle is used by Digital customer service engineers to
connect test equipment that monitors AC power.

Controls and Indicators 3–13

Chapter 4

Booting
This chapter describes how to boot the system. Sections include:
•

How booting works

•

Boot devices

•

Regular boot procedure

•

Boot device selection

•

Boot processor selection

•

Booting from an HSC disk
VAXcluster boot overview
Sample VAXcluster boot

•

Booting from an Ethernet-based compact disk server
CD server boot command
Selecting an Ethernet service

•

Ethernet boot overview

•

Sample target-initiated Ethernet boot
Step 1, Gather information at target node
Step 2, Enter information into executor’s NCP volatile database
Step 3, Boot from the target node

Booting 4–1

4.1 How Booting Works
The boot program reads the virtual memory boot program
(VMB) from the boot device.
VMB in turn boots the
operating system.
Figure 4–1: Boot Procedure

Enter BOOT command
at the
console prompt

System reinitializes
and self-test
is performed

Boot primitive on the
primary processor reads bootblock from boot device

Bootblock with boot
primitive loads VMB
into memory

VMB
boots the
operating system

msb-0009-88

4–2 VAX 6000 Series Owner’s Manual

Table 4–1: Boot Procedure
Step

Procedure

You enter BOOT command from the console terminal in console mode.
The BOOT command specifies the boot device and the path needed to reach it.

System reinitializes and performs self-test.

Boot primitive is invoked from console ROM on the boot processor.
Boot primitive reads the bootblock from the specified boot device and
transfers control to the bootblock.

The bootblock contains code and a pointer to VMB.
The bootblock loads VMB into the first 256-Kbyte block of
available memory.

Once VMB is loaded into memory, the bootblock transfers control to VMB,
which in turn starts the operating system.

Boot primitive
Each boot device has a small program called a boot primitive that is
stored in ROM on each processor with the console program. The boot
primitive reads the bootblock from its boot device. How to load boot
primitives is explained in Appendix E.
Boot device
The boot device contains the bootblock and typically also contains VMB.
The system can be booted from one of four boot devices: the system
console load device, a local system disk connected through a KDM70 or a
KFMSA, a disk connected to the system through a CI adapter (CIXCD),
or a disk connected to the system through an Ethernet adapter. See
Appendix D for a list of boot devices connected to the system by VAXBI
adapters.
Bootblock
The bootblock is logical block zero on the system disk; it contains the
block number where the virtual memory boot (VMB) program is located
on the system disk and contains a program that, with the boot primitive,
reads VMB from the system load device into memory.
VMB
The virtual memory boot program (VMB.EXE) boots the operating
system. VMB is the primary bootstrap program and is stored on the
boot device. The goal of booting is to read VMB from the boot device
and load the operating system.

Booting 4–3

4.2 Boot Devices
The system can be booted from one of four boot devices:
the system console load device, a local system disk, a disk
connected to the system through a CIXCD adapter, or by
Ethernet from a remote disk on another system.

Figure 4–2: Boot Devices
XMI or VAXBI
CI

CONSOLE
LOAD
DEVICE

ETHERNET

CONSOLE
LOAD DEVICE

CD
SERVER

LOCAL
DISK
VAX SYSTEM
HSC

DISK

DISK
msb-0314C-91

4–4 VAX 6000 Series Owner’s Manual

Table 4–2: Boot Devices
Device

Location

Console load
device

Tape drive in the upper left corner of the system cabinet, a TF857
tape drive in an SFxxx cabinet, or an Ethernet-based CD server.
All are used for booting standalone backup or diagnostics. See Section 2.1.

Local disk

Disk connected to the system through a KDM70 or KFMSA adapter. Regular boot procedure specifies such a disk as default boot device for individual systems that are not VAXclustered or networked.

CI disk

Disk located on system’s HSC controller connected to the system by the CIXCD adapter on the XMI.

Ethernet disk

Disk connected to another system on the Ethernet, through the DEMNA
Ethernet port interface or the FDDI DEMFA adapter.

You have a choice of five boot device locations. They are:
•

A local console load device

•

A local disk

•

A remote console load device

•

A remote disk on an HSC controller

•

An Ethernet disk on another system

The console load device can be used to boot the standalone backup program
and the VAX Diagnostic Supervisor.
Typically, you designate the local boot device as the default boot device after
the initial boot of the system in installation. You can also store the BOOT
specification parameters by giving these parameters a nickname. See the
BOOT command in Chapter 5 for more information on storing boot device
parameters.
Boot devices can also be on the optional VAXBI. See Appendix D for boot
devices supported by the VAXBI.

Booting 4–5

4.3 Regular Boot Procedure
With the system in console mode, you issue a BOOT
command. You can give a complete specification in which
the qualifiers determine the boot device, or you can use a
nickname.

Figure 4–3: Regular Boot Procedure
BOOT /XMI:m /R5:n /R3:r /NODE: sstt /BI:u /FILENAME:x /DSSI:y /PORT:z DDww
Invokes
BOOT
command
Selects
XMI node

Register 5 optional
parameters for VMB
Register 3 optional unit
number information
Selects HSC controller
on the VAXcluster
Selects optional VAXBI
boot device adapter
Specifies file used to
boot system from an
NI-based server
Selects a node on
the DSSI bus
Selects a DSSI port

Selects boot device and
hexadecimal unit number
msb-0441A-90

4–6 VAX 6000 Series Owner’s Manual

Figure 4–3 shows the components of the BOOT command. The /XMI node
number you enter corresponds to an adapter; if you have an optional VAXBI,
the /XMI node number will correspond to a DWMBB adapter and you must
then use the /BI qualifier to specify the node number of the boot device on
that VAXBI.
When using the /R5:n qualifier, see Appendix F for the values of n. The
/R3:r qualifier is used with VMS when you boot from a shadow set, where r
is two unit numbers. The first unit number is the functional unit number of
the shadow set, and the second unit number is the physical unit number of
one of the disks in the shadow set. Refer to your operating system manual
for more details.
To designate an HSC disk as the boot device, you use the /XMI and /NODE
(and /BI, if the CI adapter is a VAXBI device) qualifiers with their respective
node numbers. The /XMI node number must be an adapter, the /NODE
node number carries the CI node number of one or two HSC controllers,
and DDww, where DD specifies the device type as a disk and ww is the
hexadecimal unit of the disk boot device.
To designate a DSSI disk as the boot device, you use the /XMI and
/DSSI_NODE qualifiers with their respective node numbers. The /XMI node
number is a KFMSA adapter, the /DSSI_NODE number is the adapter that
provides access to the boot device. The /PORT qualifier specifies the DSSI
bus 1 or 2 on the KFSMA adapter and, DDww, where DD specifies the
device type and ww is the hexadecimal unit of the boot device.
To designate an Ethernet-based CD server as the boot device, use the /XMI
qualifier to specify the node number of the DEMNA or DEMFA adapter,
and, /FILENAME:x, where x specifies the 1- to 16-character file name that
the CD server loads during the boot process.
For convenience, you can store a BOOT command under a nickname, using
the SET BOOT command. Any four characters can be used for a nickname.
However, to avoid confusion, use nicknames that are different from device
specifications. Also, note that the system reserves the name DEFAULT to
specify a special saved boot specification, which is called when you enter
the BOOT command without a nickname, so DEFA should not be used as
a nickname. The default boot specification is also used when the control
panel is set to Auto Start.
You can store up to 10 saved boot specifications, in addition to the default
specification. Table 4–4 gives the specific mnemonics for each device type.
See Section 5.18.1 for details on creating nicknames for boot devices. See
Section 5.6 for more information on the BOOT command.

Booting 4–7

4.4 Boot Device Selection
You can boot the operating system in a number of ways.
Table 4–3 lists some examples.

Table 4–3: Sample BOOT Commands
Boot Procedure

BOOT Command

Boot from in-cabinet
console load device

BOOT CSA1

Boot VAX/DS from an
in-cabinet console load
device

BOOT /R5:10 CSA1

Boot from local RA disk

BOOT /XMI:m DUww

Section 5.6

Boot from local RF disk

BOOT /XMI:m /DSSI_NODE:y /PORT:z DIww

Section 5.6

Boot from HSC disk

BOOT /XMI:m /R5:v/NODE:sstt DUww

Section 4.6
Appendix F

Boot from a DSSI TF tape

BOOT /XMI:m /DSSI_NODE:y /PORT:z MIww

Section 5.6

Boot from an
Ethernet-based CD server

BOOT /XMI:m /FILENAME:ISL_LVAX_n EX0

Section 4.7

Boot over FDDI from a CD
server

BOOT /XMI:m /FILENAME:ISL_LVAX_n FX0

Section 4.7

Boot VAX/DS from an
Ethernet-based CD server

BOOT /XMI:m/FILENAME:ISL_LVAX_x1 /R5:10 EX0
Section 4.7

Boot over the Ethernet
from a VAXBI device

BOOT /XMI:m /BI:x ET0

Section 4.8

Boot VAX/DS from disk

BOOT /XMI:m /R5:10 DUww

Appendix F

Conversational boot

BOOT /XMI:m /R5:1 DUww

Appendix F

Boot from VMS shadow set

BOOT /XMI:m /R3:w /NODE:sstt DUww

Section 5.6

1 Where x is a letter that indicates the version.

4–8 VAX 6000 Series Owner’s Manual

Refer to

You can issue a complete boot specification, or you can use a nickname that
has been defined for a complete boot specification. Issuing BOOT alone will
boot from whatever has been set as the default boot.
When you use the BOOT CSA1 command, you designate the in-cabinet TF
or TK tape drive as your boot device.
Boot device mnemonics are listed in Table 4–4.

Table 4–4: Boot Device Mnemonics
Mnemonic

Device

DIxx

KFMSA

Disk

XMI

DUxx

KDB50

Disk

VAXBI

KDM70

Disk

XMI

CIBCA

Disk

VAXBI

CIXCD

Disk

XMI

DEBNI

Disk

VAXBI

DEBNA

Disk

VAXBI

EXxx

DEMNA

Disk

XMI

FXxx

DEMFA

Disk

XMI

MIxx

KFMSA

Tape

XMI

MUxx

TBK70

Tape

VAXBI

ETxx

Device Type

Bus

Booting 4–9

4.5 Boot Processor Selection
One processor is selected as the boot processor, and
all other processors become secondary processors. This
determination is made by the system at power-up or
initialization, and can be altered by using console
commands.

Figure 4–4: Determining the Boot Processor
SECONDARY
PROCESSORS

BOOT
PROCESSOR

1. PROCESSORS RUN
SELF-TEST

2. PROCESSORS
DETERMINE BOOT
PROCESSOR

3. BOOT AND SECONDARY
PROCESSORS ASSIGNED
msb-0166-89

4–10 VAX 6000 Series Owner’s Manual

Each processor has an image of the console program and boot code in ROM,
but there is only one console terminal and a single system control panel.
One processor is designated as the boot processor (or primary processor) and
becomes the primary communicator to the console program. The signals
from the console terminal and system control panel are bused on the XMI
and are driven by the boot processor.
At power-up or initialization of the system, the console program in each
processor begins parallel execution. Each processor performs self-test and
then checks with the other processors to determine which processor becomes
the boot processor. The boot processor is the processor with the lowest node
ID number, passing self-test, that is eligible to become the boot processor
(see Section 5.18.2).
Once the boot processor has been determined, all other processors on the
system become secondary processors. The console programs in secondary
processors wait for commands from the boot processor.

Booting 4–11

4.6 Booting from an HSC Disk
4.6.1 VAXcluster Boot Overview
This section describes booting VMS from a VAXcluster.
ULTRIX is booted in the same way, except that R5 bits must
be specified (see Appendix F).
Figure 4–5: Booting from a CI-Based VAXcluster
SYSTEM TO
BE BOOTED

XMI

CIXCD

VAX

VAX
STAR
COUPLER

HSC50
node 02

VAX

RA
HSC70
node 0E

msb-0315-91

4–12 VAX 6000 Series Owner’s Manual

When you boot VMS from a VAXcluster, you need to gather the following
information:
•

Node number of the HSC controller(s)

•

Device address of the disk unit that will execute boot

•

Location of the system root

The node number of an HSC controller is a 2-digit hexadecimal number.
The device type is of the form DU0 (see Section 5.6). The location of the
system root is a hexadecimal number that indicates the system to be booted.
Figure 4–5 shows a sample VAXcluster configuration. Note that there are
two HSC controllers with node numbers 02 and 0E in this configuration.
Section 4.6.2 discusses a CI boot on the system configuration shown in
Figure 4–5.
If your system is part of a VAXcluster and you want it to boot from the
cluster system disk, you may set its default boot specification to this disk
using the SET BOOT console command (see Section 5.18.1).

Booting 4–13

4.6.2 Sample VAXcluster Boot
This section shows a sample boot from a system to be booted
in the VAXcluster configuration shown in Figure 4–5.
Example 4–1: Sample VAXcluster Boot

>>> SHOW CONFIGURATION
Type
Rev
1+ KA65A
(8080) 0006
2+ KA65A
(8080) 0006
3+ KA65A
(8080) 0006
6+ MS65A
(4001) 0084
7+ MS65A
(4001) 0084
8+ MS65A
(4001) 0084
9+ MS65A
(4001) 0084
D+ CIXCD
(0C05) 1652
E+ DEMNA
(0C03) 0600

! Enter command.
!
! Find the XMI address of
! the CIXCD, which is the
! VAXcluster interface.
! The CIXCD is XMI D.

! /R5:70000000" /NODE:0E02# DUC$

>>> BOOT /XMI:D

Initializing system

#123456789 0123456789 0123456789 0123456789 012345#
F

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

P
+
E
+
E

P
+
B
+
B

TYP
STF
BPD
ETF
BPD

.
.

A4
64

A3
64

A2
64

A1
64

.
.

ILV
256 Mb

Console = V1.00

RBDs = V1.00

EEPROM = 1.00/1.00

Loading system software

* Initializing adapter
* Adapter initialized successfully
* Connecting to HSC
* Connecting to MSCP server layer
* Connecting to boot disk
* Reading bootblock from disk
* Passing control to transfer address
[operating system banner appears]

4–14 VAX 6000 Series Owner’s Manual

NODE #

SN = SG01234567

! SHOW CONFIGURATION displays the positions of modules. The first

column identifies each module’s node, slot location, and self-test status.
The second column entries are the device names; the third, the device
type codes. The last column shows the revision level of each module.
The CIXCD is located at XMI node D. Enter this value D in the BOOT
command as the argument to the /XMI qualifier.

" In the BOOT command, the system root is the argument to the /R5

qualifier. In Example 4–1 the system root for VMS SYS7 is specified.
(To boot ULTRIX, the appropriate /R5 qualifier from Appendix F would
be given.)

# The arguments to /NODE are hexadecimal HSC node numbers. In
this example they are 0E (decimal 14) and 02 (decimal 2). Listing two
arguments tells the system to connect to either the HSC at VAXcluster
node 14 or the HSC at VAXcluster node 2. The command takes a
maximum of two parameters for this qualifier. If your disk is dualported to the HSC controller, be sure to use both nodes; this gives the
system an alternate route in case one HSC is disabled.

$ DUC requests booting from a disk with hexadecimal unit number C.
% System runs self-test (see Chapter 6 for a description of the self-test
display).

& Status messages appear, indicating a successful boot.1
For more information on VAXcluster booting, see Appendix F and the VMS
installation manual.

These boot status messages apply only to Model 500 and 600 systems. See Appendix J.

Booting 4–15

4.7 Booting from an Ethernet-Based Compact Disk
Server
4.7.1 CD Server Boot Command
This section shows a sample boot on a Model 500 system from
an Ethernet-based compact disk (CD) server. The first step
is issuing the boot command.

Example 4–2: Sample Ethernet-Based CD Server Boot

>>> SHOW CONFIGURATION
Type
Rev
1+ KA65A
(8080) 0006
2+ KA65A
(8080) 0006
3+ KA65A
(8080) 0006
6+ MS65A
(4001) 0084
7+ MS65A
(4001) 0084
8+ MS65A
(4001) 0084
9+ MS65A
(4001) 0084
B+ KDM70
(0C22) 0002
D+ CIXCD
(0C05) 1652
E+ DEMNA
(0C03) 0600
>>> BOOT /XMI:E

! Enter command.
!
! Find the XMI address of the
! DEMNA, which is the Ethernet
! interface. Here, the DEMNA
! connects to the system bus at
! XMI node E.

! /FILENAME:ISL_LVAX_A " EX0 #

Initializing system
#123456789 0123456789 0123456789 0123456789 012345#

A
+
.
.
.

.
.
.
.
.

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

P
+
E
+
E

P
+
B
+
B

TYP
STF
BPD
ETF
BPD

.
.

A4
64

A3
64

A2
64

A1
64

.
.

ILV
256 Mb

Console = V1.00

RBDs = V1.00

EEPROM = 1.00/1.00

Loading system software

Example 4–2 Cont’d on next page

4–16 VAX 6000 Series Owner’s Manual

NODE #

SN = SG01234567

Example 4–2 (Cont.): Sample Ethernet-Based CD Server Boot

* Initializing adapter
* Specified boot adapter initialized successfully
* "Request Program" MOP message sent - waiting for service from remote node
* Remote service link established
* Reading boot image from remote node
* Passing control to transfer address

! SHOW CONFIGURATION displays the positions of the modules. The
DEMNA is located at XMI node E. Enter this value E in the BOOT
command as the argument to the /XMI qualifier.

" In the boot command, the /FILENAME qualifier is used to request a file
that will be loaded into system memory from the remote CD server. In
this example the file ISL_LVAX_A is the argument to the /FILENAME
qualifier.

# EX0 specifies the DEMNA adapter as the boot device.
$ System runs self-test (see Chapter 6 for a description of the self-test
display).

% Boot status messages are displayed (see Appendix J for the boot status
and error messages displayed by Model 500 and 600 systems).

Booting 4–17

4.7.2 Selecting an Ethernet Service
The second step of booting over the Ethernet with a CD
server is selecting the service that boots VMS.
Example 4–3: Selecting an Ethernet Service
Ethernet Initial System Load Function
FUNCTION
ID
1
2
3
4
-

FUNCTION
Display Menu
Help
Choose Service
Stop

Enter a function Id value: 3

Service options:
1 = Find Services
2 = Enter Known Service Name
=>1

Working
Servers found: 1
Service Name Format:
Service Name
Server Name
Ethernet ID
#1
VMS054
ESS_08002B150589
08-00-2B-15-05-89
#2
CD_BIN_83371
ESS_08002B150589
08-00-2B-15-05-89
Enter a number =>1

[operating system banner appears]

4–18 VAX 6000 Series Owner’s Manual

! The Ethernet Initial System Load Function menu is displayed.
" The system prompts you for a function ID value. Enter 3 to select a
service.

# The Service options menu is displayed. Enter 1 to display the available
Ethernet servers and services. In this example one server, ESS_
08002B150589, is found on the Ethernet. Next, the Service Name
Format is displayed, followed by the services. Service #1, VMS054,
is used to boot VMS.

$ Enter 1 to select service #1.
% The operating system banner appears.

Booting 4–19

4.8 Ethernet Boot Overview
To boot VMS over the Ethernet, you use the Network
Control Program (NCP). The system supports booting over
the Ethernet, both trigger booting and booting initiated by
the system as a target node.

Figure 4–6: Trigger Booting Using Ethernet
EXECUTOR
SYSTEM

COMMAND
SYSTEM

NCP

MOP

TARGET
SYSTEM

LOADER

MOP TRIGGER
MESSAGE
msb-0014-88

Figure 4–7: Target-Initiated Booting by Ethernet
EXECUTOR SYSTEM

MOP PROGRAM
LOAD REQUEST

NCP
ETHERNET

CONSOLE

MOP

MOP LOAD
OPERATION

TARGET SYSTEM
msb-0015-88

4–20 VAX 6000 Series Owner’s Manual

The Ethernet is used to boot in two ways. Figure 4–6 and Figure 4–7
illustrate these methods.
A trigger boot initiates a BOOT command from a command system, which
sends the command over the Ethernet to the executor system, which causes
a boot in the target system (the VAX 6000 series system). The target system
loads its boot program from the boot device that is designated as the default.
(The default can be a local disk or the Ethernet.) The target system must
have its control panel key switches at Auto Start and Enable. Commands
are issued only from the command node, not from the target machine.
Target-initiated booting (Figure 4–7) is initiated by a console BOOT
command from the target system. This BOOT command specifies an
Ethernet controller as the boot device:
BOOT /XMI:m /R5:v EX0

(See Section 4.3 and Section 5.6 for more information on the BOOT
command.)
Information must be entered in the executor system for the boot to succeed.
Although the BOOT command is initiated at the VAX 6000 target node, the
executor node Network Control Program’s (NCP) volatile database requires
an entry for the target node.
Section 4.9 shows an example of a target-initiated Ethernet boot.

Booting 4–21

4.9 Sample Target-Initiated Ethernet Boot
To perform a target-initiated boot over the Ethernet:
(1) gather information at the target node, (2) enter the
information into the Network Control Program volatile
database on the executor node, and (3) issue a BOOT
command from the target node. Example 4–4 through
Example 4–6 show this procedure.

4.9.1 Step 1, Gather Information at Target Node
This section presents an example of booting over the
Ethernet, in a target-initiated boot from a VAX 6000 series
system.

Example 4–4: Step 1, SHOW Ethernet

>>> SHOW ETHERNET
Ethernet Adapters:
XMI:E 08-00-2B-08-3D-64
FDDI Adapters:
XMI:D 08-00-26-1C-0D-B7

! Enter command on target machine.

! The DEMNA is XMI node E. Its hardware
! Ethernet address follows.
! The DEMFA is XMI node D. Its FDDI
! hardware address follows.

4–22 VAX 6000 Series Owner’s Manual

The first step in an Ethernet boot is to gather the information from your
system that you need in the Ethernet boot.

! Use the SHOW ETHERNET command to find the address of your

system on the Ethernet and write it down. You load this address into
the executor system’s volatile database in the next step (Section 4.9.2).

" The system reports the hardware Ethernet address for the DEMNA.
The DEMNA is at XMI node E.

The system also reports the FDDI hardware address for the DEMFA
adapter.
The system manager of the target system and the system manager of the
executor system assign a node name and a network address for the target
machine. In Example 4–4 the assigned node name is TARGET, and the
node network address is 9.961.

Booting 4–23

4.9.2 Step 2, Enter Information into Executor’s NCP Volatile
Database
The second step of booting over an Ethernet is entering the
target node information into the Network Control Program
(NCP) volatile database on the executor system.
Example 4–5: Step 2, Entering Target Node Information
$ MCR NCP

! On the executor system, at
! the DCL prompt, run NCP.
! NCP prompt appears.
! Enter information from the
! target node that you
! gathered in Step 1.

NCP>

NCP> set node TARGET service circuit MNA-0
NCP> set node TARGET address 9.961
NCP> set node TARGET hardware address 08-00-2B-08-3D-64
NCP> set node TARGET tertiary loader sys$system:tertiary_vmb.exe
NCP> show node TARGET char

! Check information by showing
! node TARGET’s characteristics.
Node Volatile Characteristics as of DD-MMM-YYYY 00:00:01
Remote node

9.961

(TARGET)

Service circuit
Hardware address
Tertiary loader
NCP>
NCP> sho circuit mna-0 char

= MNA-0
= 08-00-2B-08-3D-64
= sys$system:tertiary_vmb.exe

(

! Prompt returns; show
! circuit characteristics.

Circuit Volatile Characteristics as of DD-MMM-YYYY 00:00:01
Circuit = MNA-0
State
Service
Designated router
Cost
Router priority
Hello timer
Type
Adjacent node
Listen time

(

= on
= enabled
= 9.739 (ABCDEF)
= 4
= 64
= 15
= Ethernet
= 9.739 (ABCDEF)
= 45

Example 4–5 Cont’d on next page

4–24 VAX 6000 Series Owner’s Manual

Example 4–5 (Cont.): Step 2, Entering Target Node Information
NCP>
NCP> sho line MNA-0 char

)

! Prompt returns; show
! line characteristics.

Line Volatile Characteristics as of DD-MMM-YYYY 00:00:01
Line = MNA-0
Receive buffers
Controller
Protocol
Service timer
Hardware address
Device buffer size

= 6
= normal
= Ethernet
= 5000
= 08-00-2B-06-01-00
= 1498

)

On the executor system, under VMS or the executor’s operating system,
run NCP, the Network Control Program, on an appropriate privileged
account. Enter the information into the volatile database. The main piece
of information required for booting is the hardware address. However, the
database structure requires the rest of the information to qualify as a valid
record entry.

! Run NCP.
" Assign the service circuit.
# Assign the node name (in this example, TARGET) and the network
address (9.961).

$ Enter the hardware address found in Step 1, Section 4.9.1.
% Enter the tertiary loader pathname. In this example the tertiary loader
comes from a directory named SYS$SYSTEM. Check your operating
system documentation for details.

& Check your work, using the SHOW NODE command.
' The service circuit code is dependent on your hardware.
( Check the circuit characteristics. Service must be enabled.1
) Check the line characteristics. The service timer is usually set to 5000
for an Ethernet boot.

If you need to change the circuit characteristic to enable, you must turn the circuit off, set
service to enable, and turn the circuit on again quickly, or all links could be lost to the
system.

Booting 4–25

4.9.3 Step 3, Boot from the Target Node
The third step in Ethernet booting is to issue the BOOT
command from the target node.

Example 4–6: Step 3, Booting from the Target Node
>>> BOOT /XMI:E EX0

! Enter BOOT command

Initializing system
#123456789 0123456789 0123456789 0123456789 012345#
F

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

P
+
E
+
E

P
+
B
+
B

TYP
STF
BPD
ETF
BPD

.
.

A4
64

A3
64

A2
64

A1
64

.
.

ILV
256 Mb

Console = V1.00

RBDs = V1.00

EEPROM = 1.00/1.00

NODE #

SN = SG01234567

Loading system software
* Initializing adapter
* Specified adapter initialized successfully
* "Request Program" MOP message sent - waiting for service from remote node
* Remote service link established
* Reading boot image from remote node
* Passing control to transfer address
[operating system banner appears]

4–26 VAX 6000 Series Owner’s Manual

Enter the BOOT command from the console terminal in console mode. Use
the XMI node number that you found in Step 1, Section 4.9.1, describing
the path of the Ethernet controller.1
Because the target VAX 6000 series system has been registered in the NCP
volatile database of the executor system, the Ethernet boot completes. The
executor system determines the location of the boot program.

If your system has a VAXBI and a DEBNI or DEBNA Ethernet adapter, you must enter
an additional /BI:n node qualifier.

Booting 4–27

Chapter 5

Console
The console program for the VAX 6000 series follows VAX console standards
as described in Chapter 11, VAX Console Subsystems, of the VAX Systems
Hardware Handbook — VAXBI Systems.
This chapter describes the console, its functions, and its language.
Examples are given for each console command and its qualifiers.1
Individual sections include:
•

Description of console

•

Console functions

•

Console mode

•

Console command language control characters

•

Console command language syntax

•

Console commands

•

BOOT

REPEAT

START

CLEAR EXCEPTION

RESTORE EEPROM

STOP

CONTINUE

SAVE EEPROM

TEST

DEPOSIT

SET BOOT

UNJAM

EXAMINE

SET CPU

UPDATE

FIND

SET LANGUAGE

HALT

SET MEMORY

HELP

SET TERMINAL

INITIALIZE

SHOW

Sample console session

The RESTORE EEPROM and SAVE EEPROM commands apply only to systems having a
TK tape drive. Qualifiers for a specific model (or models) are identified.

Console 5–1

5.1 Description of Console
The console subsystem consists of a console terminal,
console program located in ROM on the CPU modules,
and dedicated memory.
The console program runs on
all processors and is automatically entered when the
boot processor encounters a restart condition or when an
operator invokes console mode on the console terminal.

Figure 5–1: Console

LA75
PRINTER

VT400 SERIES
TERMINAL

msb-0138B-91

5–2 VAX 6000 Series Owner’s Manual

Table 5–1: Console Parts and Functions
Part

Function

Console terminal

Used for input, entering console commands.

Console printer

Provides a hardcopy record of console sessions.

Console
terminal port

Connects the console terminal to the system.

Console program

Software interface; translates console commands to the processors; resides in ROM on each processor.

Dedicated memory

The console communications area (CCA) in main memory that allows the console programs on each processor to communicate with each other.

In multiprocessor systems, the console program runs on all processors,
and the console program on the primary processor communicates with
the console terminal (see Section 4.5). Each processor communicates with
the others through a segment of shared main memory called the console
communications area (CCA).
To use the console terminal in console mode, set the upper key switch on
the control panel to the Enable position. The lower key switch can be at
Update or Halt. The control panel is described in Chapter 3.
You designate a terminal as the console terminal by connecting it to the
console terminal port. The console terminal port connection is on the I/O
distribution panel above the AC power controller (see Section 2.4). The
default console baud rate is 1200 when a system is installed. See the SET
TERMINAL command for instructions on changing the defaults. The break
key can also be used to change the baud rate (see Section 5.4).
When the system is in console mode, the terminal has exclusive use of the
system.
The console prompt is:
>>>

Console 5–3

5.2 Console Functions
Using the console program, you can examine and modify the
system memory and registers, boot or restart an operating
system, designate a primary processor, disable a vector
processor, and return to program mode.

Table 5–2: Console Functions
Console Use

Commands Used

Bootstrap operating system

BOOT

Change console terminal
parameters

SET TERMINAL, SAVE EEPROM, RESTORE
EEPROM

Continue program mode

CONTINUE, START

Clear error state in some registers

CLEAR EXCEPTION

Deposit to or change memory
interleave

FIND, DEPOSIT, SET MEMORY

Deposit or change registers

DEPOSIT

Designate primary processor or
disable a vector processor

SET CPU

Display system parameters

SHOW

Examine memory

FIND, EXAMINE

Examine registers

EXAMINE

Execute ROM diagnostics

TEST

Exit from program mode

CTRL/P

Remove English from error messages

SET LANGUAGE

Run diagnostics

TEST, BOOT, INITIALIZE

Receive information on
console commands

HELP

Set system parameters

SET

Start system

BOOT, INITIALIZE, START, CONTINUE

Stop system or device

STOP

Store boot specifications

SET BOOT

5–4 VAX 6000 Series Owner’s Manual

You use the console terminal to control the system manually, correct errors,
determine the status of machine registers and counters, determine the
contents of storage, and revise the contents of storage.
Following self-test or a SET CPU console command, one processor in a
multiprocessor system is designated as the primary or boot processor. The
location of the primary processor is determined at startup or when the
system is reset. The primary processor performs a bootstrap or warm
restart of the system. The operating system controls the other processors
from the primary processor.
Nonprimary processors are called secondary processors.
Secondary
processors communicate with the console terminal through the primary
processor when performing I/O during a console session. For information
on how the primary processor is determined, see Section 4.5.
Appendix G gives a summary list of each console command and its
functions.

Console 5–5

5.3 Console Mode
To enter console mode from program mode, turn the upper
key switch on the front control panel to the Enable position
and type CTRL/P at the console terminal.

Figure 5–2: Console Switch When in Console Mode

FRONT

Standby

Run

Enable

Battery

Secure

Fault

Update
Halt
Auto Start

Restart

msb-0174A-91

The console terminal can operate in two modes: program mode and console
mode. In program mode, the console terminal operates like a user terminal
on the system and is under control of the operating system. In console
mode, the system and the console terminal are operating under the console
program.
When the console terminal operates in program mode, any input to the
terminal is passed on to the operating system, as if the console were another
terminal. When the console terminal operates in console mode, input is
passed to the console program running on the primary processor.
To enter console mode, set the upper key switch to the Enable position,
and type CTRL/P on the console terminal; or you can power up with

5–6 VAX 6000 Series Owner’s Manual

Halt selected. If you type CTRL/P when the upper key switch is in the
Secure position, the CTRL/P is passed on to the operating system, and the
operating mode does not change.
CTRL/P interrupts program mode on the boot processor. The secondary
processors continue operating in program mode until they must wait for
resources locked by the primary processor. Some I/O devices also require
the attention of the primary processor. If a system remains in console mode
for more than 30 seconds, various system timeouts could cause the system
to hang when an attempt is made to return to program mode.
If you want to halt a secondary processor, you can issue a STOP command
(see Section 5.21).
To resume program mode, use one of these commands:
CONTINUE

Resumes the program that was interrupted by the CTRL/P

START

Restarts the primary processor at a specified address

The console mode prompt is >>>. After entering a command, you may
receive a system error message with number codes in the form:
?nnnn <message>

where nnnn is a number in hexadecimal format.1 These codes indicate an
error or a halted processor. See Appendix H for a listing of error codes for
Model 400 and higher systems. Appendix I lists Model 300 error codes;
Appendix J lists status and error codes for Model 500 and 600 systems.
When a secondary processor issues an error message, the primary processor
is responsible for displaying the error on the console terminal. The primary
processor displays these messages with a prefix indicating the node of the
originating processor. For example, if a secondary processor at node 5
halted, the primary processor would display the error message:
Node 5:
Node 5:
Node 5:
Node 5:

?0006 Halt instruction executed in kernel mode.
PC = E00D26B4
PSL = 041F0600
ISP = 000002F0

On Models 300 and 400 a system error message and number code will appear as:

?nn <message>

Console 5–7

5.4 Console Command Language Control
Characters
Eleven ASCII control characters have special meaning when
you type them on the console terminal running in console
mode. See Table 5–3.

Table 5–3: Console Control Characters
Character

Function

BREAK

Increments the console baud rate, if enabled.

CTRL/C

Causes the console to abort processing of a command.

CTRL/O

Causes the console to discard output to the console terminal until the next CTRL/O is entered.

CTRL/P

In console mode, acts like CTRL/C . In program mode, causes the boot processor to halt and begin running the console program.

CTRL/Q

Resumes console output that was suspended with CTRL/S .

CTRL/R

Redisplays the current line.

CTRL/S

Suspends console output on the console terminal until CTRL/Q is typed.

CTRL/U

Discards all characters on the current line.

DELETE

Deletes the previously typed character.

ESC

Suppresses any special meaning associated with a given character.

RETURN

Carriage return; ends a command line.

BREAK increments the console terminal baud rate to the next higher rate and
displays a new console prompt. If you use BREAK at the highest baud rate,
the program "wraps around" to the lowest rate. You can quickly synchronize
the console baud rate to the console terminal if the default speeds do not
match. To do this, hit BREAK repeatedly until the console prompt ">>> "
appears. The baud rates are 300, 600, 1200, 2400, 4800, 9600, 19200, and
38400. (Model 600 does not support 38400.) It is not recommended to run
faster than 1200 baud.
CTRL/C aborts processing of a command. Echoed as ^C, CTRL/C also resumes
output which you suspended using CTRL/O. When you type CTRL/C as part
of a command line, the line is deleted as if you entered CTRL/U.

5–8 VAX 6000 Series Owner’s Manual

CTRL/O stops output to the console terminal until you enter the next CTRL/O.
CTRL/O is echoed as ^O followed by a carriage return and is not echoed
when you reenable output. Output is also reenabled when the console
prompts for a command, issues an error message, enters program mode,
or when you type CTRL/P or CTRL/C.
CTRL/P works like CTRL/C and is echoed as ^P, if the console terminal is in
console mode. If the console terminal is in program mode and is secured,
CTRL/P is not echoed, but is passed to the operating system for processing.
If the console is in program mode and is not secured, CTRL/P halts the
processor and begins the console program; it also can terminate the Z
command.
CTRL/Q resumes console output on the console terminal that you suspended
with CTRL/S. The CTRL/Q key is not echoed.
CTRL/R is echoed as ^R, followed by a carriage return, line feed, and printing
of the current command line, omitting deleted characters. This command
is useful for hardcopy terminals.
CTRL/S suspends output to the console terminal until you type CTRL/Q. Any
characters you enter after CTRL/S are buffered but not echoed until output
is resumed. The CTRL/S input is not echoed.
CTRL/U discards all characters that you entered on the current line. It is
echoed as ^U, followed by a carriage return, line feed, and a new console
prompt.
DELETE deletes the previously typed character. If you define your console
terminal as a hardcopy terminal (SET TERMINAL /HARD), a Delete is
echoed with a backslash [ \ ] followed by the character being deleted. If you
delete several characters consecutively, the system echoes only the deleted
characters, followed by another backslash at the end of the series. This
displays the deleted characters surrounded by backslashes.

With a video console terminal, each Delete backs up the cursor and erases
the previously displayed character.
ESC (escape) suppresses any special meaning associated with the character
that immediately follows it. Control characters that would terminate a Z
command are passed through to the target node. The character is echoed
as "$". (On VT200 terminals and up, use CTRL/3 in place of the ESCAPE
key.)
RETURN ends a command line.
received by the program.

Any command entered before Return is

Console 5–9

5.5 Console Command Language Syntax
The console command language has syntax rules for forming
commands. Commands contain up to 80 characters, can
be abbreviated, and accept qualifiers. Tabs and spaces are
compressed. Numbers are in hexadecimal notation.

Table 5–4: Console Command Language Syntax
Command Parameter

Attribute or Action

Length

80 characters maximum.

Abbreviation

Varies with the command; usually the shortest unique
combination of letters.

Multiple adjacent spaces

Treated as a single space.

Multiple adjacent tabs

Treated as a single space.

Qualifier(s)

Can appear after the command keyword or after any symbol or number in the command; are preceded by a slash ( / ).

Numbers

Most appear in hexadecimal format.

No characters

Treated as a null command; no action taken.

NOTE: Model 600 provides command recall; that is, pressing the Uparrow
key recalls the previous command typed.

5–10 VAX 6000 Series Owner’s Manual

The console program accepts commands up to 80 characters long. This does
not include the terminating carriage return or any characters you delete as
you enter the command. A command longer than 80 characters causes an
error message of the form:
?0036 Command too long.

You can abbreviate commands and some qualifiers by dropping characters
from the end of the word. You must enter the minimum number of
characters to identify the keyword unambiguously. In the command
reference sections that follow, characters that you can omit appear within
square brackets ( [ ] ).
Multiple adjacent spaces and tabs are compressed and treated as a single
space. The program ignores leading and trailing spaces.
You can use command qualifiers after the command keyword or after any
symbol or number in the command. See individual keyword descriptions
for examples.
Most numbers in console commands are in hexadecimal notation. However,
the console program does accept decimal notation for console baud rate,
register names (R0, R1, and so on), and vector registers.
You can use uppercase or lowercase characters for input.
program converts all lowercase characters to uppercase.

The console

A command line with no characters is a null command. The console
program takes no action and does not issue an error message. The console
prompt returns.

Console 5–11

5.6 BOOT
The BOOT command initializes the system and begins the
boot program. See Section 4.1 for information on how
booting works on a VAX 6000 series system. The examples
are explained in Section 5.6.2. For details on the SET BOOT
command, see Section 5.18.1.

5.6.1 BOOT Command Examples and Qualifiers
Examples
1.

>>> BOOT

! Boots from the special boot
! specification named DEFAULT.

>>> BOOT/XMI:C DU0

! Boots from a disk with hex unit no. 0 con! nected via a KDM70 controller at XMI node C.

>>> BOOT DIAG

! Boots from the saved boot specification
! that was created and given the name DIAG.

>>> BOOT /XMI:E/BI:4/R5:70000000/NODE:0E02 DU0
! Boots on a VAXcluster from an HSC con! troller dual-ported at unit numbers 0E and 02
! with a system root of SYS7. A VAXBI device
! is used to boot this system.
! See Section 4.6.2.

>>> BOOT /XMI:E /FILENAME:ISL_LVAX_B EX0
! Boots VAX/DS from an Ethernet-based CD server.
! This example shows access from a DEMNA adapter.
! CD server can also be accessed over the FDDI
! using the DEMFA adapter; device then would be FX0.
! The server boots the system with the file
! ISL_LVAX_B.

5–12 VAX 6000 Series Owner’s Manual

>>> BOOT /XMI:E /DSSI_NODE:4 /PORT:1 DI5
! Boots from a disk with unit number 5 connected by the
! KFMSA adapter and the controller at DSSI node 4, port 1.

>>> BOOT /XMI:E /DSSI_NODE:5 /PORT:2 MI3
! Boots from a TF tape on a DSSI.

Table 5–5: BOOT Command Qualifiers
Qualifier

Function

/X[MI]:number

Specifies the XMI node number of the node that connects the boot device.

/R5:number

Specifies the hexadecimal value to be loaded into register R5 immediately before the virtual memory boot (VMB) program receives control.
Use as a bit mask to select VMB options and to set the system root directory.
See Appendix F.

/R3:number

Specifies the hexadecimal value to be loaded into register R3 immediately before the virtual memory boot (VMB) program receives control. This qualifier is used when multiple unit numbers must be specified: for example, when booting from VMS shadow sets. If /R3 is specified, the unit number portion of the device name is ignored.

/N[ODE]:number

Specifies the remote node(s) that provide access to the boot device. The /XMI (and optionally /BI) qualifiers must have identified a controller that supports "nodes" such as a VAXcluster adapter. The /NODE qualifier would then specify the VAXcluster node number(s) of the HSC controlling the boot device.

/B[I]:number

Specifies a VAXBI node that connects the boot device.
The /XMI qualifier must have selected a node containing a DWMBB/A.

/FILE[NAME]:file

Specifies the file name used to boot from an Ethernetbased server.
The file name can be 1 to 16 characters in length.

/D[SSI_NODE]:number

Specifies the DSSI node that provides access to the boot device. The /XMI qualifier must have selected a node containing a KFMSA adapter.

/PO[RT]:number

Specifies DSSI port 1 or 2 on the KFMSA adapter.

Console 5–13

5.6.2 BOOT Command Description
Figure 5–3: BOOT Command
BOOT /XMI:m /R5:n /R3:r /NODE: sstt /BI:u /FILENAME:x /DSSI:y /PORT:z DDww
Invokes
BOOT
command
Selects
XMI node

Selects boot device and
hexadecimal unit number
msb-0441A-90

5–14 VAX 6000 Series Owner’s Manual

The BOOT command syntax is:
B[OOT][/qualifier] [<parameter>]

BOOT command qualifiers are summarized in Table 5–5. The qualifier
includes a variable which is a node number, a value to be loaded into a
register, or the name of a file when using the /FILENAME qualifier. A
variable is a required argument to the qualifier. If you do not specify a
variable, you receive an error message in the form:
?0021 Illegal command

In the syntax <parameter> can be a string of the form ddnn. The variable
dd is a 2-character mnemonic for the device type (MI or MU for tape, DU or
DI for disk, EX, FX, or ET for Ethernet, or CSA1 for the in-cabinet console
load device), and nn is a 1- or 2-digit hexadecimal number for the boot
device. The nn portion of the boot device is ignored if the /R3 qualifier is
used.
You can also use <parameter> as a 1- to 4-character name of a saved boot
specification that you have created. Your saved specification needs to supply
values for the boot device and other qualifiers, if required. You can override
any saved qualifier value by specifying the qualifier with a new value. For
information on creating a saved boot specification, see Section 5.18.1.
If you omit <parameter>, the program uses the default saved boot
specification. You define a default saved boot specification by using the
reserved name DEFAULT and the SET BOOT command. Use unique names
when you name your saved boot specifications. To avoid confusion, choose
names for saved boot specifications that are distinct from the actual device
names.
When you have successfully specified the command, your console terminal
waits while the system initializes itself and performs self-test. When
the operating system comes up, your console terminal displays the login
banners of the operating system, and your console terminal is then
operating in program mode.

Console 5–15

5.7 CLEAR EXCEPTION
The CLEAR EXCEPTION command is used to clear error
states in registers.

Examples
1.

>>> EXAMINE 21800000
! Attempt to examine a non?0029 Machine check accessing memory. ! existent address produces
! a machine check and sets
>>> CLEAR EXCEPTION
! some error bits.
XBE0
= 000000C0
! Register values before
XFADR0 = 61900008
! CLEAR EXCEPTION clears
XBEER0 = 01240001
! the error bits.
PCSTS = 000008C0
>>>

>>> ^P
>>> SHOW CONFIGURATION
Type
1+ KA65A
(8080)
2+ KA65A
(8080)
3+ KA65A
(8080)
4+ KA65A
(8080)
5+ FV64A
(0000)
6+ MS65A
(4001)
8+ MS65A
(4001)
9+ MS65A
(4001)
A+ MS65A
(4001)
D+ CIXCD
(0C05)
E+ DEMNA
(0C03)

Rev
0006
0006
0006
0006
0001
0084
0084
0084
0084
1652
0600

>>> CLEAR EXCEPTION
XBE0
= 00000081
XFADR0 = 61900008
XBEER0 = 01240001
PCSTS = 000008C0
>>> CONTINUE

5–16 VAX 6000 Series Owner’s Manual

! Issued to clear error
! state that exists.

The CLEAR EXCEPTION command syntax is:
CL[EAR] EX[CEPTION]

This command is used to clear error states that remain from a previous
command, a sequence of commands, or a console action. The console
displays what is currently in the registers shown in the examples and
then clears write-one-to-clear bits in the XBER, XBEER, and CPU-specific
registers.
In most cases the console program cleans up the error state. However, if
an error state is generated after a CTRL/P, the CONTINUE command will
not clean up error state. For example, if you type CTRL/P, then issue a
SHOW CONFIGURATION command, and then CONTINUE, some error
state exists and may cause spurious errors. CLEAR EXCEPTION should
be used to clear these errors before giving a CONTINUE command.

Console 5–17

5.8 CONTINUE
The CONTINUE command begins processing at the point
where it was interrupted by a CTRL/P console command.
Programs continue processing at the address currently in
the program counter of the processors.

Example
$ ^P

! Stops processing on boot procesor;
! processor enters console mode.
!
?0002 External halt (CTRL/P, break, or external halt)
PC = 801DBAA6
! System responds with error message;
PSL = 04C38201
! system has halted with address
ISP = 80B15200
! 801DBAA6 in the program counter (PC).
!
>>>
!
>>> [console session begins] !
.
!
.
!
.
!
!
>>> CONTINUE
! Processing resumes at the address
! where processing was stopped by
! CTRL/P. Here, processing continues
! at address 801DBAA6.

5–18 VAX 6000 Series Owner’s Manual

The CONTINUE command takes no arguments. Its syntax is:
C[ONTINUE]

CONTINUE causes the processor to resume program mode, executing at the
address currently in the program counter (PC). This address is the address
that was in the PC when the primary processor received the CTRL/P input
to interrupt processing and change to console mode. The system displays
the hexadecimal PC and the hex values for PSL and –SP (see Appendix H).
When the boot processor receives a CONTINUE command, it does not
perform processor initialization as it would for a boot procedure. The boot
processor just returns to the program it was processing.
Following execution of the CONTINUE command, the console terminal
enters program mode, and any ASCII characters entered on the console
terminal are passed on to the operating system. In program mode, the
console terminal acts like any other terminal on the system, until a CTRL/P
is issued to toggle it back to console mode.
NOTE: The CONTINUE command should be used selectively. Do not use
the CONTINUE command to return to program mode if you have modified
memory in console mode.

Console 5–19

5.9 DEPOSIT
The DEPOSIT command stores data in a specified address.

5.9.1 Syntax and Qualifiers
Table 5–6: DEPOSIT Command Qualifiers
Qualifier

Meaning

Defines data size as a byte.

Defines the address space as the general register set, R0 through R15.

Defines the address space as the internal processor registers, accessed through MTPR and MFPR instructions.

Defines data size as a longword; initial default.

/M1

Defines the address space as a vector indirect register; accesses addresses 400 and higher.

/N:<count>

Defines the address space as the first of a range.2
quired value with /N.

Defines the address space as physical memory; initial default.

Defines data size as a quadword; initial default for vector registers (except for VCR and VLR).

Defines the address space as virtual memory. All access and protection checking occur. Use when your operating system has been running prior to system halt.3

/VE1

Defines the address space as the vector register set.

Defines data size as a word.

<count> is a re-

1 Used only with an attached vector processor (Models 400 and 500).
2 The

console deposits to the first address, then to the specified number of succeeding addresses. Even if the address is ’–’, the succeeding addresses are at higher addresses (that is, the symbol specifies only the starting address, not the direction).
3 If memory management has not been enabled, virtual addresses are equal to physical addresses. If access is not allowed to a program running with the current processor status longword (PSL), the console issues an error message. Virtual space deposits cause the PTE<M> bit to be set in the mapping PTE and force the processor write buffer to be flushed.

5–20 VAX 6000 Series Owner’s Manual

The DEPOSIT command syntax is:
D[EPOSIT] [/qualifier] <address>

<data>

where /qualifier is a value from Table 5–6, and the variable <data> is a
hexadecimal value to be stored. The value must fit in the data size to be
deposited. The variable <address> is a 1- to 8-digit hexadecimal value or
one of the following:
•

PSL, the processor status longword. You cannot use any address space
qualifier with PSL.

•

PC, the program counter. The address space is set to /G.

•

SP, the stack pointer. The address space is set to /G.

•

Rn, the general purpose register n. The register number is in decimal.
The address space is set to /G.

•

For use with an attached vector processor:
VCR, 7-bit Vector Count Register. No address qualifier is permitted.
VLR, 7-bit Vector Length Register. No address qualifier is permitted.
VMR, 64-bit Vector Mask Register. No address qualifier is permitted.
V0–V15, vector registers. Elements of a vector register are specified
Vn:mm, where n is a decimal number 0–15 specifying the vector
register, and mm is a hex number 0–3F specifying the element within
the vector register. The address qualifier must be set to /VE.

•

+, the location immediately following the last location you referenced in
an EXAMINE or DEPOSIT command. For physical and virtual memory,
the referenced location is the last location plus the size of the reference
(1 for byte, 2 for word, 4 for longword). For other address spaces, the
address is the last referenced address plus one.

•

–, the location immediately preceding the last location you referenced
in an EXAMINE or DEPOSIT command. For physical and virtual
memory, the referenced location is the last location minus the size of
the reference (1 for byte, 2 for word, 4 for longword). For other address
spaces, the address is the last referenced address minus one.

•

*, the last location you referenced in an EXAMINE or DEPOSIT
command.

•

@, the location addressed by the last location you referenced in an
EXAMINE or DEPOSIT command.

If no qualifiers are given with subsequent commands, the system uses
the qualifiers from the preceding command as the defaults. With the /M
qualifier, the address is a 3-digit hex number (400 or above).

Console 5–21

5.9.2 Examples
Examples
1.

>>> D/P 27 0

!
!

Deposits the value of 0 to physical
address 27.

>>> D/N:8 R0 FFFF

Loads registers R0-R8 with FFFF.

>>> DEPOSIT/P/B/N:1FF 0 0

!
!
!

Deposits zeros to the first
512 bytes of physical memory
beginning with address 0.

>>> DEPOSIT/VE V12 0

!
!

Deposits zero into all 64 elements
of vector register V12.

>>> DEPOSIT VLR 1

!
!

Deposits one in the Vector Length
Register.

>>> DEPOSIT/M

!
!

Deposits zeros to vector indirect
register with address 440 (hex).

440 0

5–22 VAX 6000 Series Owner’s Manual

The DEPOSIT command directs data into the specified address. If you do
not specify any address space or data size qualifiers, the defaults are the last
address space or data size specified in a DEPOSIT or EXAMINE command.
After processor initialization, the default address space is physical memory,
the default data size is longword, and the default address is zero.
If the specified value is too large to fit in the data size, the console program
ignores the command and issues an error message. If the specified value
is smaller than the data size to be deposited, the console program fills the
high order data positions with zeros. If you specify conflicting data sizes or
address spaces, the console program ignores the command and issues an
error message.

Console 5–23

5.10 EXAMINE
The EXAMINE command displays the contents of a specified
address.
The qualifiers are identical to the DEPOSIT
command’s qualifiers.

5.10.1 Syntax and Qualifiers
Table 5–7: EXAMINE Command Qualifiers
Qualifier

Meaning

Defines data size as a byte.

Defines the address space as the general register set, R0 through R15.

Defines the address space as the internal processor registers,
cessed through MTPR and MFPR instructions.

Defines data size as a longword; initial default.

/M1

Defines the address space as a vector indirect register; accesses addresses 400 and higher.

/N:<count>

Defines the address space as the first of a range.2
quired value with /N.

Defines the address space as physical memory; initial default.

Defines data size as a quadword; initial default for vector registers (except for VCR and VLR).

Defines the address space as virtual memory. All access and protection checking occur.3

/VE1

Defines the address space as the vector register set.

Defines data size as a word.

ac-

<count> is a re-

1 Used only with an attached vector processor (Models 400 and 500).
2 The

console examines the first address, then the specified number of succeeding addresses.
Even if the address is ’–’, the succeeding addresses are at higher addresses; that is, the symbol specifies only the starting address, not the direction.
3 If memory management has not been enabled, virtual addresses are equal to physical addresses. If access is not allowed to a program running with the current processor status longword (PSL), the console issues an error message. Virtual space deposits cause the PTE<M> bit to be set in the mapping PTE and force the processor write buffer to be flushed.

5–24 VAX 6000 Series Owner’s Manual

The EXAMINE command syntax is:
E[XAMINE] [/qualifier] [<address>]

where /qualifier is a value from Table 5–7, and <address> is a 1- to 8-digit
hexadecimal value or one of the following:
•

PSL, the processor status longword. You cannot use any address space
qualifier with PSL.

•

PC, the program counter. The address space is set to /G.

•

SP, the stack pointer. The address space is set to /G.

•

Rn, the general purpose register n. The register number is in decimal.
The address space is set to /G.

•

*, the last location you referenced in an EXAMINE or DEPOSIT
command.

•

@, the location addressed by the last location you referenced in an
EXAMINE or DEPOSIT command.

Console 5–25

5.10.2 Examples
Examples
1.

>>> E/N:8 R0

Examines registers R0-R8.

>>> EXAMINE/P/B/N:1FF

Examines the first 512 bytes.

>>> EXAMINE/N:5/W/P -

!
!
!

Examines the previous word
in the physical address space
and the next five words.

>>> E/I 3E

!
!

Examines the system ID register.
System responds with output.

!
!

Examines the Vector Length
Register.

!
!
!
!

Examines the vector indirect
register at hex address 440.
/M is used to access vector
indirect registers.

0000003E

0B000001

>>> EXAMINE VLR
M 00000001 0E

>>> EXAMINE/M

440

M 440 FFFFFFFF 00000000

>>> EXAMINE/VE V0
VE V00:00
VE V00:02
VE V00:04
VE V00:06
VE V00:08
VE V00:0A
VE V00:0C
VE V00:0E
VE V00:10
VE V00:12
VE V00:14
VE V00:16
VE V00:18
VE V00:1A
VE V00:1C

!
!

Examines vector register V0; system
displays all 64 elements of register V0.

00000000 00000002
00000000 00000002
00000000 00000002
00000000 00000002
00000000 00000002
00000000 00000002
00000000 00000002
00000000 00000002
00000000 00000002
00000000 00000002
00000000 00000002
00000000 00000002
00000000 00000002
00000000 00000002
00000000 00000002

5–26 VAX 6000 Series Owner’s Manual

VE V00:01
VE V00:03
VE V00:05
VE V00:07
VE V00:09
VE V00:0B
VE V00:0D
VE V00:0F
VE V00:11
VE V00:13
VE V00:15
VE V00:17
VE V00:19
VE V00:1B
VE V00:1D

VE V00:1E
VE V00:20
VE V00:22
VE V00:24
VE V00:26
VE V00:28
VE V00:2A
VE V00:2C
VE V00:2E
VE V00:30
VE V00:32
VE V00:34
VE V00:36
VE V00:38
VE V00:3A
VE V00:3C
VE V00:3E

VE V00:1F
VE V00:21
VE V00:23
VE V00:25
VE V00:27
VE V00:29
VE V00:2B
VE V00:2D
VE V00:2F
VE V00:31
VE V00:33
VE V00:35
VE V00:37
VE V00:39
VE V00:3B
VE V00:3D
VE V00:3F

The system response to the EXAMINE command is in hexadecimal
notation:
<address space identifier>

<data>

where <address space identifier> can be one of these values:
•

P — Physical memory. When virtual memory is examined, the <address
space identifier> is P and <address> is the translated physical address.

•

G — General register.

•

I — Internal processor register.

•

For use with an attached vector processor:
M — Vector indirect register. This identifier is also returned when the
PSL is examined.
VE — Vector data register.

Console 5–27

5.11 FIND
The FIND command causes the console program to search
main memory starting at address zero for a page-aligned
256-Kbyte block of good memory (that has no errors) or for
a restart parameter block (RPB). If the block is found, its
address plus 512 is left in the stack pointer. If the block is
not found, an error message is issued.

Examples
1.

>>> FIND/MEMORY
>>>

! Searches for a 256-Kbyte memory
! block; returns prompt when found.

>>> F
>>>

! Searches for restart parameter
! block; returns prompt when found.

>>> F/RPB
>>>

! Searches for a restart parameter
! block; returns prompt when found.

Table 5–8: FIND Command Qualifiers
Qualifier

Meaning

/ME[MORY]

Searches for a 256-Kbyte memory block.

/RP[B]

Searches for a restart parameter block.
This is the default qualifier. Usually used when the system has been running prior to a system halt. If you use this qualifier before the system has run the operating system, the command searches all memory, which causes a long delay.

5–28 VAX 6000 Series Owner’s Manual

The FIND command syntax is:
F[IND] [/qualifier]

where /qualifier is either /MEMORY or /RPB. The FIND command searches
main memory to find a page-aligned 256-Kbyte block of good memory or a
restart parameter block. If you do not use a qualifier, the FIND command
searches for a restart parameter block, as if you used a /RPB qualifier.
There is a wait, while the system searches all memory. This may take up
to 2 minutes for each 32 Mbytes of memory.
On some VAX systems, the FIND command is a necessary step in the system
boot procedure. However, on a VAX 6000 series system, the boot program
includes the process of finding the appropriate memory block to boot. You
do not use this command during normal boot procedures.
When the memory block is found, its address plus 512 is left in the stack
pointer (SP). This convention is established because you load the virtual
memory block (VMB) program into the memory block you just found. VMB
uses the first page of memory to build the restart parameter block (RPB).

Console 5–29

5.12 HALT
The HALT command is a null command for the system
operating in console mode. The command is accepted, but
no action is taken since the processor has already halted in
order to enter console mode.

Example
>>> HALT
?0026 Halted

! You enter the HALT command.
!
! System responds with error message
! that indicates the system already
! is halted.

5–30 VAX 6000 Series Owner’s Manual

The HALT command syntax is:
HALT

where the command takes no arguments.
On other VAX systems, the HALT command stops the processors. However,
on VAX 6000 series systems, HALT has no effect, because the boot processor
is already halted as a requisite condition for console mode.
See the STOP command, Section 5.21.

Console 5–31

5.13 HELP
The HELP command provides basic information on the
console commands, when the console terminal is in console
mode.

Examples
1.

>>> HELP
BOOT
FIND
REPEAT
CLEAR_EXCEPTION
HALT
RESTORE_EEPROM
CONTINUE
HELP
SAVE_EEPROM
DEPOSIT
INITIALIZE
SET
EXAMINE
SelfTest_Output
CTRL_Characters
!

SHOW
START
STOP
TEST

UNJAM
UPDATE
Z

For more information, type HELP <topic>.

>>> HELP FIND
FIND
Searches memory for the specified item.
Qualifiers
/MEMORY
/RPB

- Searches for first 256 Kbytes of good memory.
- Searches for a Restart Parameter Block.

>>> HELP INIT
INITIALIZE [qualifiers] [node]
Resets the specified XMI node.
resets the entire system.

If node

number is omitted,

Qualifiers
/BI:bi-node

- Resets the specified BI node. The node
parameter must specify an XMI-to-BI adapter.

>>> HELP !
! comment
Treats the remainder of the command line as a comment.

5–32 VAX 6000 Series Owner’s Manual

The syntax for the HELP command is:
HELP [<command>]

where <command> is one of the entries listed in the main HELP printout.
The HELP command operates when the console program error messages
are set in English mode (see Section 5.18.3). To see a list of all HELP files
available, enter HELP or HELP HELP at the console prompt, followed by
a carriage return. The system responds with a list of available HELP files.
When you issue a SET LANGUAGE INTERNATIONAL command and then
enter HELP [<command>], you receive the error message:
?005C

From the error messages in Table H–2, you can see that ?005C indicates
that no help is available.

Console 5–33

5.14 INITIALIZE
The INITIALIZE command performs a reset.
You can
initialize the entire system, a specified XMI node (except
memory), or a specified VAXBI node.

Examples
1.

>>> INITIALIZE 1

! Initializes node 1 on the XMI.
! No self-test results are displayed.

>>> I/B:2 E

! Initializes node 2 on a VAXBI
! where E is the node on the XMI
! that goes to node 2 on the VAXBI.

>>> I

! Resets the entire system.

#123456789 0123456789 0123456789 0123456789 012345#
F

A
o
.
.
.

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

P
+
E
+
E

P
+
D
+
D

P
+
E
+
E

P
+
B
+
B

.
.

A4
64

A1 .
64 .

.
.

Console = V1.00
>>>

A3
64

RBDs = V1.00

A2
64

EEPROM = 1.00/1.00

NODE #
TYP
STF
BPD
ETF
BPD

XBI E +
ILV
256 Mb

SN = SG01234567

! Prompt returns following self-test.

5–34 VAX 6000 Series Owner’s Manual

Table 5–9: INITIALIZE Command Qualifiers
Qualifier

Meaning

/B[I]:<VAXBI-node>

Can be used only if the specified XMI node is a DWMBB/A.
This qualifier resets the single adapter at node <VAXBInode> on the specified VAXBI.

None

If no XMI node number is given and a /BI qualifier is omitted, the system resets all nodes on the XMI (and optional VAXBI) and prints out self-test results.

The INITIALIZE command syntax is:
I[NITIALIZE] [/qualifiers] [<XMI-node>]

where <XMI-node> indicates the XMI node to be initialized.
The INITIALIZE command can be used to reset the system or a specified
node — except memory nodes. If <XMI-node> is omitted, the entire system
is reset. If the /BI qualifier is used, the XMI node is a DWMBB that connects
to the VAXBI bus containing the VAXBI node to be initialized. If the <XMInode> is a DWMBB and the /BI qualifier is not used, then all devices on
the VAXBI bus are reset.
The INITIALIZE command and the Restart button on the system control
panel perform the same function: they both reset the machine.
If the node number you designate in an INITIALIZE command does not
have a module in it, you receive an error message of the form:
?0043 Unable to initialize node.

If the node number specifies a memory module, you receive this message:
?0049 Memory cannot be initialized.

Self-test results are displayed after a system reset but not after a node
reset. See Section 6.2 through Section 6.7 for how to interpret self-test
results.

Console 5–35

5.15 REPEAT
The REPEAT command reexecutes the command that you
pass as its argument. You can use the REPEAT command
with any command except itself. The key combination CTRL/C
stops the REPEAT command.

Example
>>> REPEAT E/P 10

! Continuously displays the
! contents of physical memory at
! address location 10. To stop
! the display, enter a CTRL/C.

5–36 VAX 6000 Series Owner’s Manual

The REPEAT command syntax is:
R[EPEAT] <command>

where <command> is any command other than REPEAT.
REPEAT works as a continuous repeat. The command you pass as an
argument to the REPEAT command continues to be executed until you
stop the process with CTRL/C.

Console 5–37

5.16 RESTORE EEPROM
The RESTORE EEPROM command can be used if your
system has a TK tape drive1 as a console load device.
This command copies the TK tape’s EEPROM image to the
EEPROM of the boot processor.

Example
! Lower key switch must be in Update position.
! Load the TK tape with EEPROM contents.
! When the yellow light on the TK70 drive
! stays on, enter RESTORE command.
>>> RES E
?006E EEPROM Revision = x.xx/y.yy
?0070 Tape image Revision = x.xx/y.yy
! System displays the revision level of the
! EEPROM and the TK tape.
! Console program asks if you want to restore;
! the default is no. Enter Y to continue.
Proceed with EEPROM update? (Y or N) >>> Y
?006A EEPROM changed successfully.
>>>

! Restore complete; prompt returns.

The RESTORE EEPROM command syntax is:
RES[TORE] E[EPROM]

The RESTORE EEPROM command copies information from the TK tape
that you previously saved by using the SAVE EEPROM command (see
Section 5.17). Before the information is copied to the EEPROM of a
processor, you are shown the revision level of the information that resides
on the tape as well as information that presently resides on the EEPROM.
Then you are asked if you wish to continue the restore operation.
The steps for using RESTORE EEPROM include:
1. Load the TK tape cartridge containing saved EEPROM data into the TK
tape drive. This rewinds the tape to the beginning, so that restoration
proceeds from this point. See Appendix B for information on the tape
drive operation.
1

RESTORE EEPROM not implemented on TF devices.

5–38 VAX 6000 Series Owner’s Manual

2. Put the control panel’s lower key switch in the Update position (see
Section 3.3).
3. Put the control panel’s upper key switch in the Enable position, and
type CTRL/P at the console terminal to put the terminal in console
mode (see Section 5.3).
4. Move to the processor whose EEPROM contents you wish to restore.
Normally, all EEPROM contents will be the same. If you are restoring
the contents of the boot processor, proceed to the next step. If you
wish to restore the contents of a secondary processor, change the boot
processor using the SET CPU command (see Section 5.18.2).
5. At the prompt, enter RESTORE EEPROM. The console program
queries you, requiring your confirmation to proceed with the RESTORE
EEPROM operation.
6. Enter Y to indicate your intention to proceed. The restore process takes
less than 2 minutes to complete.
7. When the console prompt returns, the restore operation is complete.
Restored information includes:
Systemwide console parameters
(baud rate, interleave, terminal characteristics)
Saved boot specifications
Diagnostic patches
Console patches
Boot primitives
8. Rewind the TK tape.
9. Reset the system using the INITIALIZE command or the control panel
Restart button. All restored changes are visible following a system
reset.
10. Use the SHOW command to verify the contents of the EEPROM.
NOTE: With the UPDATE command you can restore EEPROM contents on
all secondary processors (see Section 5.24), but you must be sure all ROMs
are the same revision. The EVUCA program can also be used to restore the
EEPROM contents (see Appendix E ).
Because each system has its own identifying information stored in the
EEPROM, only the TK tape for that system should be used for a RESTORE
EEPROM operation.

Console 5–39

5.17 SAVE EEPROM
The SAVE EEPROM command can be used if your system
has a TK tape drive1 as a console load device. This command
copies the EEPROM contents of the boot processor to the TK
tape.

Examples
1.
>>> SAVE EEPROM

! Load a TK tape. When the yellow
! light on the TK drive stays on,
! the tape is ready. Enter SAVE command.
! System prompts user to proceed. Enter
! a Y to continue.

Proceed with save to tape? (Y or N) >>> Y
?006C EEPROM saved to tape successfully.
>>>
! System confirms SAVE is complete.

>>> SA E
?003D

! SAVE EEPROM to the TK tape.
!
Error initializing I/O device.
! TK tape not initialized.
! Reload and reenter the command.

The SAVE EEPROM command syntax is:
SA[VE] E[EPROM]

SAVE EEPROM copies information from the EEPROM of the boot processor
to the beginning of the tape in the TK tape drive. As the information is
copied, the TK controller writes a block and then checks it against the
contents of the EEPROM to verify. You should save the contents of the
EEPROM every time customer service installs a new EEPROM patch level.
The SAVE EEPROM command overwrites whatever is on the TK tape. To
be safe, use a blank tape cartridge.
There are several steps to the SAVE EEPROM procedure:
1. Load a TK tape cartridge (write-enabled) into the TK tape drive and
press the control panel button. This rewinds the tape so it records from
1

SAVE EEPROM not implemented on TF devices.

5–40 VAX 6000 Series Owner’s Manual

the beginning of the tape. See Appendix B for information on the tape
drive operation.
2. Put the control panel’s upper key switch in the Enable position, and
type CTRL/P at the console terminal to put the terminal in console
mode (see Section 5.3).
3. If you wish to save the contents of a secondary processor’s EEPROM,
first make it the boot processor using the SET CPU command. (See
Section 4.5 and Section 5.18.2.)
4. At the prompt, enter SAVE EEPROM. This operation overwrites any
existing information on the TK cartridge, so be sure you have inserted
an appropriate tape.
5. The console program queries you, requiring your confirmation to
proceed with the SAVE EEPROM operation.
6. Enter Y to indicate your intention to proceed. The save process takes
less than a minute to complete.
7. The console program confirms that the save operation has completed
successfully. When the console prompt returns, the save operation is
complete. Saved information includes:
Systemwide console parameters
(baud rate, interleave, terminal characteristics)
Saved boot specifications
Diagnostic patches
Console patches
Boot primitives
8. Rewind the tape. When the green light turns on and the beep sounds,
you can remove the tape. Label and write-protect the tape (see
Section B.4).
Because each system has its own identifying information stored in the
EEPROM, only the TK tape for that system should be used for a SAVE
EEPROM operation.

Console 5–41

5.18 SET Commands
SET commands allow you to change the configuration
parameters on the boot device, primary processor, memory,
and terminal, and to modify the output of the error
messages. To store the new parameters in the processor’s
EEPROM, the control panel’s lower key switch must be
in the Update position. Some SET commands take effect
immediately, but the changes will be lost at the next node
or system reset if the EEPROM is not updated.

Figure 5–4: Lower Key Switch in Update Position

FRONT

Update
Halt
Auto Start

msb-0171A-91

5–42 VAX 6000 Series Owner’s Manual

This section describes the following SET commands:
•

SET BOOT

•

SET CPU

•

SET LANGUAGE

•

SET MEMORY

•

SET TERMINAL

If you issue a set command and the control panel’s lower key switch is not
in the Update position, you may receive the following error message:
?0040

Key switch must be at "Update" to update EEPROM.

Despite the error message, the change completes and remains until the
primary processor or system is reset.
Whenever you issue a SET command, the console program tries to pass the
current values of all parameters that can be set to all system processors.
This requires that all system processors be in console mode. You receive an
error message if any processor is still running. Processors not in console
mode are not updated. Use the STOP command to stop each processor, or
issue an INITIALIZE command to stop all processors. (See Section 5.21
and Section 5.14.)
When you issue a system reset, the system checks the validity of the
systemwide parameters on each node and sends an error message to you if
the settings on any node do not match those on the current boot processor
or are corrupted.

Console 5–43

5.18.1 SET BOOT
The SET BOOT command allows you to store a BOOT
command by a nickname for easy reference. Then you
can reference the full BOOT command by the nickname.
The lower key switch on the control panel must be set to
Update.

Examples
1.

! Turn key switch to Update.
>>> SET BOOT DIAG /XMI:D DU0
>>>
! This creates a saved boot specification called DIAG
! that boots the disk unit 0 from XMI node D.
! SHOW BOOT command displays all saved BOOT specifications.
>>> SHO BOOT
DEFAULT /XMI:D DU1
DIAG
/XMI:D DU0

>>> SET BOOT DIAG
>>> SHO BOOT
DEFAULT /XMI:D DU1

! Removes the boot specification saved
! under the name DIAG.
! SHOW BOOT command confirms DIAG is re! moved from saved BOOT specifications,
! from example #1 above.

>>> SET BOOT DEFAULT /XMI:E /NODE:0405 /R5:40000000 DU0
! Sets the default boot device for the
! system to be disk unit 0 (DU0) on the
! VAXcluster; booting from system root 4.
! 04 and 05 are the specified VAXcluster
! node numbers of the HSC that controls
! the boot device.
! SHOW BOOT command confirms DEFAULT is
>>> SHO BOOT
! changed in saved BOOT specifications.
DEFAULT /R5:40000000 /XMI:E /NODE:0405 DU0

5–44 VAX 6000 Series Owner’s Manual

The SET BOOT command syntax is:
SE[T] B[OOT] <nickname> [<boot-parameters>]

where <nickname> is a 1- to 4-character name for the boot specification you
are saving.
The string <boot-parameters> is any legal set of BOOT command
parameters and qualifiers that do not reference another saved boot
specification. If you omit <boot-parameters>, you delete the saved boot
specification (if any) associated with <nickname>. The lower key switch on
the control panel must be set to the Update position.
You can store up to 10 saved boot specifications plus the default
specification. Avoid using saved boot specification nicknames that are
identical to device specifications.
A Digital customer service engineer sets the system default boot device
at installation. The default is chosen to point to the system disk or
VAXcluster disk and to allow the system to reboot automatically after a
power interruption.
Before you name a boot specification, you may want to enter:
SHOW BOOT

This command displays all boot specification names that have been saved
to date. See Section 5.19 for additional information on the SHOW BOOT
command.

Console 5–45

5.18.2 SET CPU
The SET CPU command allows you to specify a particular
processor as the primary processor or designate its
eligibility to become the primary processor. You can also
disable a vector processor module.

5.18.2.1 Syntax and Qualifiers

Table 5–10: SET CPU Command Qualifiers
Qualifier

Meaning

/E[NABLED]
/ALL

Processor is included in the system configuration and is enabled to leave console mode. With the /ALL qualifier all processors are enabled to leave console mode.

/NO_E[NABLED]

Processor is disabled from leaving console mode; START, BOOT,
and CONTINUE commands are ignored.

/NEX[T_PRIMARY]

Processor will be the primary (boot) processor at the next system reset.

/P[RIMARY]
/ALL

Processor will be eligible to be selected as the primary (boot) processor at the next system reset. With the /ALL qualifier all processors are eligible to become the boot processor; initial default.

/NOP[RIMARY]

Processor will not be eligible to be selected as the primary (boot) processor at the next system reset.

/V[ECTOR_ENABLED]1

Vector processor attached to the specified scalar processor is included in the system configuration and can be sent vector instructions; initial default.

/NOV[ECTOR_ENABLED]1 Vector processor attached to the specified scalar processor is excluded from the system configuration.
None

Processor immediately becomes the new primary processor; the next system prompt comes from the new primary processor.

1 Used only with an attached vector processor (Models 400 and 500).

5–46 VAX 6000 Series Owner’s Manual

The SET CPU command syntax is:
SE[T] C[PU] [/qualifier] [<XMI-node>]

where <XMI-node> is the XMI node number of the processor to be affected.
If you omit <XMI-node>, the system uses the current processor.
If you omit all qualifiers, the SET CPU command immediately causes the
specified processor to become the primary processor. The console terminal is
then connected to the new primary processor, and the next console prompt
is generated by the designated processor.
If you use qualifiers, the SET CPU command changes the processor
parameters that take effect at the next system reset. These qualifiers
modify the EEPROM (if the lower key switch is set to Update) and take
effect immediately:
•

/ENABLE

•

/NOENABLED

•

/VECTOR_ENABLED

•

/NOVECTOR_ENABLED

The /NEXT_PRIMARY qualifier acts the same as if you had issued a
SET CPU/NOPRIMARY command for all other nodes. To undo /NEXT_
PRIMARY, you can issue the SET CPU/PRIMARY/ALL command. The
/PRIMARY qualifier means that the specified processor is eligible to be
the primary processor.
The /NOVECTOR_ENABLED qualifier removes the vector processor
from the system configuration. The scalar processor is not affected.
The /VECTOR_ENABLED qualifier restores the vector processor to the
configuration.
The effect of the SET CPU command qualifiers is shown on the BPD lines
of the system self-test display (see Section 6.5).
NOTE: For performance reasons, the scalar processor of a scalar/vector pair
should not be made the primary processor when other scalar processors are
in the system.

Console 5–47

5.18.2.2 Examples
Examples
1.

>>> SET CPU/PRIMARY 1

! The processor at XMI node 1 may become the
! primary processor at the next system reset.

>>> SE CPU 1

! Processor at XMI node 1 immediately
! becomes the new primary processor.
! The next system prompt is generated
! from the processor at node 1.

>>> SET CPU/NOVECTOR_ENABLED 4

! The vector processor attached
! to the scalar processor at node 4
! is disabled.

5–48 VAX 6000 Series Owner’s Manual

Table 5–11: SET CPU Command Qualifiers’ Effect After a System Reset
Qualifier

BPD Value at Next Reset1

/NEX[T_PRIMARY]

B for boot processor; must be chosen the boot processor at the next system reset. All other CPUs show as D.

/NOE[NABLED]

D for disable; processor is not included in the configuration.

/NOP[RIMARY]

D for disable; can be only a secondary processor.

/P[RIMARY]

B if selected as the boot processor; E if it is a secondary processor.

/NOV[ECTOR_ENABLED]

D for disable; vector processor is not included in the configuration.

None

B for boot processor.

1 The key switch must be at Update when the SET CPU command is issued.

Console 5–49

5.18.3 SET LANGUAGE
The SET LANGUAGE console command changes the output
format of the console error messages. The default is English
error messages, as shown in Appendix H.

Examples
1.

! Lower key switch must be in Update
! position to store change in EEPROM.
>>> SET LANGUAGE INTERNATIONAL ! All error messages now appear as
! numeric code only, with no
! English explanation.
>>> CONTINUE
! Continue in program mode.
$
!
$ ^P
! A CTRL/P changes to console mode.
?0002
! System error message indicates
! external halt; message is in
! INTERNATIONAL format.

>>> SET LANGUAGE ENGLISH

! All error messages now appear with
! English comments and numeric code.
>>> CONTINUE
! Continue in program mode.
$
!
$ ^P
! A CTRL/P changes to console mode.
?0002 External halt (CTRL/P, break, or external halt)
PC = 801DBAA6
! System error message indicates
PSL = 04C38201
! external halt; message is ENGLISH
ISP = 80B15200
! format.

>>> SET LANGUAGE
?0021 Illegal command

! Illegal command; requires parameter.

Table 5–12: SET LANGUAGE Command Parameters
Parameter

Meaning

ENGLISH

Error messages have both a numeric code and an English explanation.

INTERNATIONAL

English explanations for error codes are suppressed.

5–50 VAX 6000 Series Owner’s Manual

The SET LANGUAGE command syntax is:
SE[T] LANG[UAGE] <parameter>

where <parameter> is a required value from Table 5–12.
The SET LANGUAGE command suppresses English explanations of a
command. The default setting is to provide complete information with the
error message.
If you use the HELP command while the console program is in International
mode, you receive the error message:
?005C

This indicates that No HELP is available, and the HELP messages have
not been translated from English and do not appear in International mode.
Issuing a CTRL/P command to the console program would generate the
following error message:
?0002 External halt (CTRL/P, break, or external halt)

If you then issue a SET LANGUAGE INTERNATIONAL command and
again type CTRL/P, the error message reads:
?0002

While the console program is in International mode, you might receive an
error message of:
?0021

If you then enter SET LANGUAGE ENGLISH and repeat the sequence
that generated the error command, the system response is:
?0021 Illegal command

Console 5–51

5.18.4 SET MEMORY
The SET MEMORY command is used to override the system
default for interleaving memory. The command takes effect
after the next system reset.

Examples
1.

>>> SET MEMORY/I:(9+7+6+5, 8, A)
! Explicitly specifies what is created
! as the system memory configuration.
! Four memories are in one set, and 8 and A
! are each in an interleave set of their own.
! Used to exclude a memory from the configuration.

>>> SET MEMORY

/INTERLEAVE:DEFAULT
! For a system with 6 memory modules:
!
4-way interleave of first 4 memories,
!
2-way interleave of remaining 2 modules.
!
! Assume memory module locations at XMI
! nodes 5 through A.

Table 5–13: SET MEMORY Qualifiers
Qualifier

Meaning

/C[ONSOLE_LIMIT]:n

Prevents the console and operating system from using memory above the specified address.

/I[NTERLEAVE]:(interleave-list)

Explicitly specifies how to interleave memory modules.

/I[NTERLEAVE]:D[EFAULT]

Uses the default interleave algorithm.

/I[NTERLEAVE]:N[ONE]

Does not interleave memory.

The SET MEMORY command syntax is:
SE[T] M[EMORY] </qualifier>

5–52 VAX 6000 Series Owner’s Manual

The console program automatically interleaves the memory modules to
give the largest possible set. The SET MEMORY command allows you
to override the default. This command modifies the configuration stored in
the EEPROM. The new configuration takes effect the next time the system
is reset or powered up.
An interleave set consists of memory modules in one-, two-, four-, or eightway configurations. Up to eight interleave sets can be configured. The
command can be used to set an upper bound on the memory used by the
console.
The default action interleaves memory so that the largest interleave factor
is obtained for each group of memory modules. If you have more modules
than you can interleave evenly, the console program repeats the criteria
with the remaining memory modules until only single arrays remain. An
interleave set will be built from like-sized memory modules or from memory
modules whose cumulative value is equal to the largest memory module in
the set. The console program configures the memory modules starting with
the lowest XMI node number, which is placed at the lowest physical address.
Interleave set A always has a starting address of 0. Subsequent interleave
sets have starting addresses that are the sum of the memory sizes of
preceding interleave sets. As can be seen in the console display, an
interleave set number of "–" indicates that the memory module was not
included in the configuration.
F

.
.

A1
64

.
.

NODE #
ILV
64 Mb

Additional information about the qualifiers includes:
•

/Console_limit:n allows you to reserve the highest addressed physical
memory for special hardware or applications, where n is that
hexadecimal address. The value is rounded up to the next even page
boundary. The console program begins building its in-memory data
structures, such as the CCA and bitmap, in memory locations below
hexadecimal address n.

•

For the /Interleave qualifier, the interleave-list can have the format
of:
(node + node ..., node,...)

where node is the XMI node number of a memory module. Commas
separate each set of modules to be interleaved. Each set contains
memory modules, separated by plus signs. The console program
configures the modules in the order you specify, placing the first module
at the lowest physical address.

Console 5–53

5.18.5 SET TERMINAL
The SET TERMINAL command sets the characteristics that
are stored for the console terminal.

Example
>>> SHOW TERMINAL
/SCOPE
/SPEED: 1200

! Enter SHOW TERMINAL.
/BREAK
! System responds with
! the parameters stored for
! /SCOPE, /SPEED, and /BREAK.

>>> SET TERM/HARDCOPY /SPEED:9600 ! SET TERM changes system
! parameters.
!
>>> SHOW TERM
! Enter the command.
/HARDCOPY /SPEED: 9600 /BREAK
! System displays the
! parameters you set.

Table 5–14: SET TERMINAL Command Qualifiers
Qualifier

Meaning

/BREAK

Enables you to adjust the baud rate using the BREAK key.

/NOBREAK

Disables the BREAK key from adjusting the baud rate.

/H[ARDCOPY]

Specifies the console terminal as a hardcopy device.

/NOH[ARDCOPY]

Specifies the console terminal as a video device.

/SC[OPE]

Specifies the console terminal as a video device.

/NOSC[OPE]

Specifies the console terminal as a hardcopy device.

/SP[EED]:n

Sets the baud rate for communication at 300, 600, 1200, 2400,
4800, 9600, 19200, or 38400.3

3 38400 is not implemented on Model 600.

5–54 VAX 6000 Series Owner’s Manual

The SET TERMINAL command syntax is:
SE[T] T[ERMINAL] [/qualifiers]

The character format for the SET TERMINAL command is always eight
bits—no parity, one stop bit.
This command immediately changes the specified parameter. The new
value is stored in the EEPROM if you have the lower key switch set to
Update. The EEPROM defaults are /SCOPE, /SPEED:1200, and /BREAK.
The /HARDCOPY qualifier controls the sequence that the console program
echoes at the console terminal when you use the Delete key to erase input
characters. With the /HARDCOPY parameter set, the console terminal
echoes each deleted character within backslashes. The /NOHARDCOPY
qualifier causes deleted characters to disappear from the video screen of
your terminal.
You can direct the console terminal output to a printer. The VT420 terminal
has a Print Screen key (the second key at the top left of the keyboard), or
you can select from four printing modes. See Installing and Using the
VT420 Video Terminal.

Console 5–55

5.19 SHOW
The SHOW command displays the current value of
parameters specified in a SET command and other
configuration information about the system.
Examples
1.

>>> SHOW ALL
Type
1+ KA65A
9+ MS65A
D+ CIXCD
E+ DEMNA

Rev
0006
0084
1652
0601

(8080)
(4001)
(0C05)
(0C03)

! Lists all system parameters,
! beginning with the system
! configuration.

Current Primary: 1
/NOENABLED/NOVECTOR_ENABLED/NOPRIMARYF

! Shows the status of CPUs
! Models 400 and 500 only

! Shows the memory interleave
6
5
4
3
2
1
0
NODE #

.
.
.
.
.
A1 .
.
.
.
.
.
64 .
/INTERLEAVE:DEFAULT
/SCOPE /SPEED: 1200 /BREAK
English
XMI:E
08-00-2B-08-3D-64
DEFAULT /R5:00000010 /XMI:E

.
.

>>> SHOW FIELD
Saved boot specifications:
DEFAULT /R5:00000010 /XMI:E

.
.

ILV
64 Mb

! Shows the terminal characteristics
! Shows the language mode
! Shows the Ethernet address
DU0 ! Shows Boot specs saved

DU0

Console terminal parameters:
/SCOPE
/SPEED: 9600 /NOBREAK
Console error message language mode:
English
Memory configuration:
F
E
D
C
B
A

.
.
.
.
.
A1
.
.
.
.
.
64
/CONSOLE_LIMIT:00100000
/INTERLEAVE:DEFAULT

.
.

Power system: C
System serial number: SG01234567

5–56 VAX 6000 Series Owner’s Manual

NODE #
ILV
64 Mb

The SHOW command syntax is:
SH[OW] <object>

where <object> is one of these commands:
A[LL]

B[OOT]

E[THERNET] F[IELD]

CO[NFIGURATION]

CP[U]

D[SSI]

L[ANGUAGE]

M[EMORY]

T[ERMINAL]

Table 5–15: SHOW Commands
Command

Information Displayed

SHOW ALL

Information provided for the SHOW commands. Some information provided for the SHOW FIELD command will not
be included when a SHOW ALL is issued.

SHOW BOOT

All BOOT commands and their nicknames that have been created by using the SET BOOT command.

SHOW CONFIGURATION

Hardware device type and revision level for each XMI (and optional VAXBI) node; also indicates whether the node passes
or fails self-test. See Appendix C and Appendix D for device type code assignments.

SHOW CPU

The primary processor and the status of other processors.
The SET CPU command assigns these values.

SHOW DSSI

DSSI bus numbers, node
bers for all DSSI devices.

SHOW ETHERNET

Ethernet hardware addresses for all Ethernet adapters on the
system and FDDI hardware addresses for all FDDI adapters.

SHOW FIELD1

Saved boot commands, console terminal parameters, console language mode, memory configuration, type of power system, and system serial number.

SHOW LANGUAGE

The mode currently set for console error messages, international or English.

SHOW MEMORY

The memory lines from the system self-test.
The ILV
line indicates the interleave active on the memory arrays, while the second line indicates the size of each memory, its node position, and the total amount of memory on the system.

SHOW TERMINAL

Current parameters set for the console terminal: baud rate
and terminal characteristics.

numbers,

and

unit

num-

1 The SHOW FIELD command applies only to Model 500 and 600 systems.

Console 5–57

5.20 START
The START command begins execution of an instruction at
the address specified in the command string. The START
command does not initialize the system.

Examples
1.

! CTRL/P stops processing;
! system enters console mode.
!
?0002 External halt (CTRL/P, break, or external halt)
PC = 80159035
! System responds with error
PSL = 04C38201
! message that the system has
ISP = 80B15200
! halted with address 80159035
! in the program counter (PC).
>>> [console session begins] !
.
!
.
!
.
!
>>> START
! Starts the system at
! address 80159035.

$ ^P

! Stops processing; system enters
! console mode.
!
?0002 External halt (CTRL/P, break, or external halt)
PC = 80044957
! System responds with error
PSL = 04C38201
! message that the system has
ISP = 80B15200
! halted with address 80044957
! in the program counter (PC).
>>> [console session begins] !
.
!
.
!
.
!
>>> START 10000
! Starts processing at address
! 10000, which is different from
! the address held in the PC at halt.

5–58 VAX 6000 Series Owner’s Manual

The START command syntax is:
STA[RT] [<address>]

where <address> is the starting address. If <address> is omitted, the
current PC content is used. In this case, the START command has the
same effect as the CONTINUE command.
When you specify an address, the START command is the same as executing
a Deposit to the program counter (PC) followed by a CONTINUE command.
That is, with the START command and an address as an argument, you
store an address in the program counter and then call for the system to
begin processing at that address.

Console 5–59

5.21 STOP
The STOP command halts a specified XMI (or optional
VAXBI) node. If the target node is a processor, the processor
enters console mode.

Examples
1.

>>> STOP 2

! Stops the processor at node 2 on the XMI.

>>> STOP E

! Stops the adapter at node E on the
! XMI. If the adapter at node E is a
! DWMBB/A, then all nodes on the
! VAXBI connected through node E are
! also stopped.

>>> STOP/BI:6 E

! Stops the adapter at node 6 on the
! VAXBI accessible through the
! DWMBB/A at node E.

>>> STO/B:6

! Same as above command.

Table 5–16: STOP Command Qualifiers
Qualifier

Meaning

/B[I]:<node>

Specifies a VAXBI node. Causes a VAXBI stop of the node at <node>
on the specified VAXBI.

<XMI-node>

Specifies an XMI node. Stops the processor or DWMBB/A at the
given node number.

5–60 VAX 6000 Series Owner’s Manual

The STOP command syntax is:
STO[P] [/qualifier] <XMI-node>

where <XMI-node> specifies the XMI node to be halted. If <XMI-node> is
a processor module, then only that node is halted. If you stop a processor
that is currently running, you receive this message:
>>>
Node n:
>>>
Node n:
>>>

?0002 External halt (CTRL/P, break, or external halt)
PC = xxxxxxxx

where n is the node you stopped, and xxxxxxxx is the address where the
processor was halted. If you issue a STOP command to a processor that is
in console mode, you do not receive a message. Processors in console mode
are already halted.
When the /BI qualifier is used, the XMI node is a DWMBB/A that connects
to the VAXBI bus containing the node to be halted.
When the /BI qualifier is not used, as in:
STO[P] <XMI-node>

if <XMI-node> is a DWMBB/A, all nodes on the VAXBI are halted.
The STOP command has no effect after a system reset. The STOP command
does not control the running of diagnostics.
The STOP command does not apply to memories.

Console 5–61

5.22 TEST
The TEST command passes control to the system self-test
diagnostics.

Example
>>> TEST/RBD

! Requests ROM-based diagnostics.
! New prompt indicates you are in RBD
RBD1>
! monitor program working from the
! device with node number 1.
RBD1> ^Z
! You enter CTRL/Z to return
! to console mode.
!
?0006 Halt instruction executed in kernel mode.
PC = 200601D8
! Console error message indicates
PSL = 041F0604
! RBD program has been halted.
ISP = 201405B4
!
>>>
! Console prompt returns.

Table 5–17: TEST Command Qualifiers
Qualifier

Meaning

/R[BD]

Transfers control to the command parser for running ROM-based diagnostics.

5–62 VAX 6000 Series Owner’s Manual

The TEST command syntax is:
T[EST] </qualifier>

The qualifier /RBD transfers control to the command parser for running
ROM-based diagnostics. This parser runs various tests and displays the
results on the console terminal. Type CTRL/Z or QUIT to return to the
console prompt.
If no qualifier is specified, self-test runs on the node at which you type
the TEST command. The console prompt then returns. See your system’s
Service Manual for more information on diagnostics.

Console 5–63

5.23 UNJAM
The console program accepts the UNJAM command.
However, UNJAM has no effect on the system, since this
system does not have an independent I/O bus reset option.

Example
>>> UNJAM
>>>

! Enter UNJAM command.
! Console prompt returns.
! UNJAM has no effect on the
! system.

5–64 VAX 6000 Series Owner’s Manual

The UNJAM command syntax is:
UN[JAM]

This command is retained for compatibility with other consoles, but has no
effect on this system, since the only bus reset is accomplished with a full
system reset.

Console 5–65

5.24 UPDATE
The UPDATE command copies the contents of the boot
processor’s EEPROM to the EEPROM of the specified
secondary processor. The control panel’s lower key switch
must be in the Update position to use UPDATE.

Examples
1.
>>> UPDATE 2
>>>

! Lower key switch must be set to
! Update; upper switch to Enable.
! Update the processor at node 2.
! There is a pause while this
! command executes. When the
! console prompt returns, update
! is complete.

>>> UPDATE ALL
>>>

>>> UPDATE 1
?0064 Operation only applies to secondary processors.
! The module at node 1 is not a
! secondary processor.

>>> UPD E
! Update the module at node E.
?004E Specified node is not a processor.
! System error message indicates
! that node E houses a memory or
! adapter module.

! Update all the secondary
! processors. There is a pause
! while this command executes.
! When the console prompt returns,
! update is complete.

5–66 VAX 6000 Series Owner’s Manual

The UPDATE command syntax is:
UPD[ATE] <node number>
UPD[ATE] ALL

-or-

where <node number> is the node number of the secondary processor
that is to receive the contents of the primary processor’s EEPROM. When
UPDATE is issued, the console program checks the ROM revision levels of
the processors. If the ROM revision level of a secondary processor does not
match that of the primary, no update is done and a message is displayed.
The secondary processor’s EEPROM is updated even if the processor is set
to NOENABLED. The UPDATE ALL command updates the EEPROMs on
all the secondary processors; the operation takes approximately 5 minutes
for each secondary processor.
The UPDATE command copies the parameters that can be set plus some
additional information stored in the EEPROM of the boot processor.
Whenever the EEPROM on the primary processor has a patch level
installed, the change should also be made in any secondary processors.
Updated information includes:
•

Systemwide console parameters
Baud rate, interleave, and terminal characteristics

•

Saved boot specifications

•

Diagnostic patches

•

Console patches

•

Boot primitives

You must set the control panel lower key switch to the Update position to
use this command. If the key switch is not in the Update position when
you issue an UPDATE command, you receive the following error message:
?0040 Key switch must be at "Update" to update EEPROM.

NOTE: An alternative to the UPDATE command is the EVUCA utility,
which also updates a processor’s EEPROM contents. See Appendix E.

Console 5–67

5.25 Z
The Z command logically connects the console terminal to
another node on the XMI. Characters typed at the console
terminal following a Z command are passed to the target
node. All output from the target node is displayed on the
console terminal.

Examples
1.

! Connect from the boot processor at
>>> Z 6
! node 1 to CPU at node 6.
?0033 Z connection successfully started.
6>>
! Prompt indicates the new processor node no.
6>> D/P 0 12345678
! Deposits data 12345678 to
! physical address 0.
!
6>> ^P
! End connection to CPU at node 6.
?0031 Z connection terminated by ^P.
>>>
! Prompt indicates you are in console
! mode on the boot processor.
>>> E/P 0
P 00000000 12345678 ! Examines physical address 0; shows data
! 12345678 was successfully deposited.
>>>

>>> Z /BI:6 E

! Connect to VAXBI node 6 through DWMBB in
! XMI slot E.
?0033 Z connection successfully started.
6>>

Table 5–18: Z Command Qualifiers
Qualifier

Meaning

/B[I]:<VAXBI-node>

Specifies connection to the VAXBI at node number indicated by <VAXBI-node>.

<XMI-node>

Specifies connection to the XMI at node number indicated by <XMI-node>.

5–68 VAX 6000 Series Owner’s Manual

The Z command syntax is:
Z [/qualifier] <XMI-node>

where <XMI-node> is required and is the number of the target node. When
used with the /BI qualifier, <VAXBI-node> specifies the target node on the
VAXBI. When no qualifier is present, <XMI-node> specifies the target node
on the XMI.
The Z command allows you to access the console program on a secondary
processor directly. It also allows you to communicate with adapters that
have ROM-based diagnostics.
Use a CTRL/P to terminate the Z command and return control to the
primary processor. Use ESC to ignore any special functions of the character
following the escape key. For example, ESC CTRL/P passes CTRL/P to the
target node.
Only one Z command is in effect at a time. You cannot issue a Z command
from one secondary processor to another secondary processor. Z commands
can be issued only from the boot processor. A processor node that is already
the target of a Z command rejects any Z commands that it receives and
issues an error message. This way your characters are not being forwarded
to more than one target node, but only to the node you have specified.
Once you have issued a Z command to access a secondary processor and
you wish to access another secondary processor, you must issue a CTRL/P
to return to the primary processor, and from there issue a Z command to
the new secondary processor you wish to access.
When you access a secondary processor, the system modifies the console
prompt to include the secondary processor node number (n>>). This
modified prompt remains until you use a CTRL/P command to return to
the primary processor.

Console 5–69

5.26 !
The ! command introduces a comment. The console program
ignores anything you enter on the command line following
the !. The ! command is useful for documenting your console
session on a hardcopy terminal for later reference.

Examples
1.

>>> ! THIS IS A COMMENT
>>>

>>> SET TERM/SCOPE
>>>

! THIS IS A COMMENT ON A COMMAND LINE

5–70 VAX 6000 Series Owner’s Manual

The ! command syntax is:
! [<comment entered here>]

You terminate the comment with a carriage return. If you want to enter
several lines of comment, begin each new line with a ! command.
If your comment line exceeds 80 characters, you receive the error message:
?0036 Command too long.

Console 5–71

5.27 Sample Console Session

#123456789 0123456789 0123456789 0123456789 012345#
F

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

M
+
.
.
.

+
E
+
E

P
+
E
+
E

P
+
B
+
B

TYP
STF
BPD
ETF
BPD

.
.

A4
64

A3
64

A2
64

.
.

A1
64

.
.

ILV
256 Mb

Console = V1.00

RBDs = V1.00

>>> EX/N:3 R0
G 00000000
G 00000001
G 00000002
G 00000003

E0140648
00000000
00000010

#FFFFFFFF

>>> SHOW CONFIGURATION
1+
2+
3+
4+
5+
6+
8+
9+
A+
D+
E+

"
V- -P

Type
KA65A
KA65A
KA65A
KA65A
FV64A
MS65A
MS65A
MS65A
MS65A
CIXCD
DEMNA

EEPROM = 1.00/1.00

NODE #

SN = SG01234567

Rev
(8080) 0006
(8080) 0006
(8080) 0006
(8080) 0006
(0000) 0001
(4001) 0084
(4001) 0084
(4001) 0084
(4001) 0084
(0C05) 1652
(0C03) 0601

>>> BOOT /XMI:D/R5:70000000/NODE:0E02 DU0
[self-test results appear]

* Initializing adapter
* Specified adapter initialized successfully
* Connecting to boot disk
?0018 Specified unit offline - Unit unknown, online to
another controller or port disabled via A, B switches
?0006 Halt instruction executed in kernel mode.
PC = E00C2329
PSL = 041F0600
ISP = 000002F0
Bootstrap failed due to previous error.
>>> BOOT /XMI:D/R5:70000000/NODE:0E02 DU0

[self-test results appear, then the operating system banner]

5–72 VAX 6000 Series Owner’s Manual

Sections of the sample console session flagged by the numbered callouts are
explained below.

! At power-up, the system performs self-test and displays the results.
See Section 6.2 for an explanation of self-test.

" The TYP line in the sample self-test display indicates that XMI slot1

5 is a vector processor attached to the scalar processor at node 4.
The dashed lines indicate that the vector processor (V-) and the scalar
processor (-P) are paired.

# The console prompt indicates that the terminal is in console mode.
Enter an EXAMINE command to examine the contents of register 0
and three additional registers. Output displays the contents for R0,
R1, R2, and R3, respectively.

$ Enter a SHOW CONFIGURATION command to show the hardware

configuration. Operator looks at configuration to find the disk controller
to know the correct qualifiers to enter with the BOOT command.
System response indicates devices’ XMI node numbers, self-test status,
device types, and contents of the revision register of the device.

% Enter BOOT command, using the CIXCD adapter at XMI node D to

locate the disk (DU0), the boot device, in a VAXcluster. Boots from an
HSC controller that is dual-ported at unit numbers 0E and 02 with a
system root of SYS7.

& System issues status and error messages.2 An error occurred during

connection to the boot disk, so a halt instruction is executed. You may
assume an error in specifying the device or in the device itself. In this
case, there was no disk pack in the disk drive. Error is corrected.

' BOOT command is reissued. The operating system begins to boot and
presents its banner to the console terminal.

1
2

Vector processors are supported on Model 400 and 500 systems only.
See Appendix J for a list of status and error messages for Model 500 and 600 systems.
Appendix H lists messages common to Model 400 and higher systems; Appendix I lists
Model 300 messages.

Console 5–73

Chapter 6

System Self-Test and Troubleshooting
This chapter discusses the testing that the system performs and the record
displayed at power-up and at a system reset. The chapter includes the
following sections:
•

Self-test overview

•

Sample self-test display

•

Self-test progress trace line

•

Self-test lines NODE #, TYP, and STF

•

Self-test lines BPD and ETF

•

Self-test lines ILV and Mb

•

Self-test identification line

•

Sample self-test display with VAXBI adapter

•

Troubleshooting during booting

•

Forcing a boot processor

System Self-Test and Troubleshooting 6–1

6.1 Self-Test Overview
The system provides a record of its testing in the console
self-test display. The control panel Fault light and the
module self-test LEDs also indicate success or failure.

Figure 6–1: Testing Sequence

#123456789 0123456789 0123456789 0123456789 012345# 1

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

P
+
E
+
B

P
+
B
E

P
E
E

P
+
D
+
D

TYP
STF
BPD
ETF
BPD

.
.

B2
64

B1
64

A2
64

A1
64

.
.

ILV
256 Mb

Console = V1.00

RBDs = V1.00

EEPROM = 1.00/1.00

>>>

6–2 VAX 6000 Series Owner’s Manual

NODE #

2
3
4

SN = SGO1234567

msb-0701B-91

Following power-up and system reset, the system performs testing and
displays the results on the console terminal. As testing begins, the red
Fault light on the control panel lights (see Section 3.5).
Most of the modules in the XMI card cage have on-board ROM used for
testing. The first indication that testing has begun on (Models 400 and
higher only) is the printing of a line of numbers, which is the first line of
the self-test display (see
in Figure 6–1). This line, called the progress
trace, is generated by a processor module in slot 1 of the XMI card cage.1
Each number displayed reflects the successful completion of tests run by
this processor. For Models 300 and 200 the start of self-test is indicated by
the NODE # line in the self-test display.

All modules have yellow LEDs on the outer edge of the module that light
when the module passes self-test. The LEDs on the modules can be viewed
from the front of the cabinet when the cabinet door is open. If a module
fails self-test, its yellow LED does not light.
This first round of testing completes, and the results are shown on the STF
line. The boot processor is then determined. This processor then generates
the results of testing to this point . The testing takes 10 to 15 seconds.

Next, the processors run additional tests using the memory modules. In this
extended testing the processor that had been designated as boot processor
could fail, so the boot processor is again determined. Results are displayed
on the ETF line .

The status of the boot processor and secondary processors is then displayed
on the second BPD line .

The boot processor next configures memory and displays the configuration.
At this point if any memory had a noncorrectable error, all memory
addresses for that module are tested, so there could be a delay before the
console prompt appears.

that displays the lines
Note that it is the boot processor determined at
after the first BPD line. The final line before the prompt is from the boot
processor’s EEPROM.
Each line of the self-test display is described in detail in the following
sections of this chapter.

If your system has a T2019 power regulator in the XMI card cage, the progress trace line
is not displayed.

System Self-Test and Troubleshooting 6–3

6.2 Sample Self-Test Display
The processor modules display the results of self-test.
Results are printed on the console terminal, as shown in
Figure 6–2.

Figure 6–2: Self-Test Results
#123456789 0123456789 0123456789 0123456789 012345# 1
F

NODE #

P
+
D
+
D

TYP
STF
BPD
ETF
BPD

3
4
5
6

.
.

ILV
256 Mb

7
8

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

P
+
E
+
B

P
+
B
E

P
E
E

.
.

B2
64

B1
64

A2
64

A1
64

.
.

Console = V1.00

RBDs = V1.00

EEPROM = 1.00/1.00
10

SN = SGO1234567
11

>>>
! Items with callout numbers are explained in this chapter.
msb-0701-91

6–4 VAX 6000 Series Owner’s Manual

The self-test printout in Figure 6–2 reflects the system configuration
listed in Table 6–1. Each numbered item in the example is explained in
Section 6.3 through Section 6.7. These sections assume the same system
configuration, when discussing the printout information.
See Section 6.8 for a description of self-test results when a VAXBI adapter
is part of the system configuration. A sample self-test display with a vector
processor is shown in Section 5.27.

Table 6–1: System Configuration for Sample Self-Test
Module

XMI Node
Number
Module Type

KA66A

Processor; disabled from being boot processor.

KA66A

Processor; fails first level of self-test.

KA66A

Processor; boot processor after first level of self-test, fails extended test.

KA66A

Processor; operating as boot processor.

MS65A

Memory (64 Mbytes); interleaved with memory at node 8 by a
SET MEMORY console command.

MS65A

Memory (64 Mbytes); interleaved with memory at node 7 by a
SET MEMORY console command.

MS65A

Memory (64 Mbytes); interleaved with memory at node A by
a SET MEMORY console command.

MS65A

Memory (64 Mbytes); interleaved with memory at node 9 by a
SET MEMORY console command.

CIXCD

I/O adapter; passes self-test.

DEMNA

I/O adapter; passes self-test.

System Self-Test and Troubleshooting 6–5

6.3 Self-Test Progress Trace Line
A line of decimal numbers indicates the progress of self-test
execution (Model 400 and higher systems).

Figure 6–3: Self-Test Results: Progress Trace

#123456789 0123456789 0123456789 0123456789 012345# 1
F

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

P
+
E
+
B

P
+
B
E

P
E
E

P
+
D
+
D

TYP
STF
BPD
ETF
BPD

.
.

B2
64

B1
64

A2
64

A1
64

.
.

ILV
256 Mb

Console = V1.00

RBDs = V1.00

EEPROM = 1.00/1.00

NODE #

SN = SGO1234567

msb-0701A-91

6–6 VAX 6000 Series Owner’s Manual

The self-test printout in Figure 6–3 reflects the system configuration listed
in Table 6–1. The first line shown in Figure 6–3, if complete, shows that
the CPU in slot 1 passed all testing. If the final # sign is missing, the last
number shown is the number of the failing test. (The number of tests varies
by model number of the system.) This line of numbers is displayed only by
the processor in slot 1 — and only when this processor undergoes power-up
or a system reset. This processor is not always the boot processor.
For example, when the system is reset or the INITIALIZE command is
issued, the progress trace line might show:
#123456789 01234567

! Test #17 (decimal) failed.

System Self-Test and Troubleshooting 6–7

6.4 Self-Test Lines NODE #, TYP, and STF
The next three lines of the self-test printout provide the node
number identification (NODE #), type of module (TYP), and
self-test status (STF) for modules in the XMI card cage. For
Models 300 and 200 the start of self-test is indicated by the
NODE # line.

Figure 6–4: Self-Test Results: NODE #, TYP, and STF

#123456789 0123456789 0123456789 0123456789 012345#
F

NODE #

P
+
D
+
D

TYP
STF
BPD
ETF
BPD

3
4

.
.

ILV
256 Mb

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

P
+
E
+
B

P
+
B
E

P
E
E

.
.

B2
64

B1
64

A2
64

A1
64

.
.

Console = V1.00

RBDs = V1.00

EEPROM = 1.00/1.00

SN = SGO1234567

>>>
msb-0701C-90

6–8 VAX 6000 Series Owner’s Manual

The system configuration being tested is discussed in Section 6.2. See
Table 6–1.

" The NODE # line lists the node numbers on the XMI bus. The nodes

on this line are numbered in hexadecimal and reflect the position of the
XMI slots as you view the XMI from the front of the cabinet through
the clear card cage door (see Figure 6–4).
XMI entries use slots 1 through E, while an optional VAXBI could have
entries in slots 0 through F (see Section 6.8). The XMI has 14 slots, and
the slot and node numbers are identical. The self-test printout reflects
the physical position of the modules in the XMI card cage.

# The TYP line in the printout indicates the type of module at each XMI
node:
•

An I/O adapter (A)

•

A scalar processor (P)

•

A vector processor (V)

•

A memory module (M)

•

A period indicating that the slot is not populated or the module is
not reporting and may be dead

$ The STF line shows the results of self-test. This information is taken
from the self-test fail bit in the XBER register of each module. The
entries are:
+ (pass)
– (fail)
o (does not apply)

System Self-Test and Troubleshooting 6–9

6.5 Self-Test Lines BPD and ETF
The fifth, sixth, and seventh lines of the self-test printout
provide information on the processors and their boot
processor designation (BPD) and the results of the extended
test (ETF).

Figure 6–5: Self-Test Results: BPD and ETF

#123456789 0123456789 0123456789 0123456789 012345#
F

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

P
+
E
+
B

P
+
B
E

P
E
E

P
+
D
+
D

TYP
STF
BPD
ETF
BPD

.
.

B2
64

B1
64

A2
64

A1
64

.
.

ILV
256 Mb

Console = V1.00

RBDs = V1.00

EEPROM = 1.00/1.00

>>>

6–10 VAX 6000 Series Owner’s Manual

NODE #

5
6
5

SN = SGO1234567
msb-0701D-91

The system configuration being tested is discussed in Section 6.2. See
Table 6–1.

% The BPD line 1 indicates boot processor designation. When the system
goes through self-test, the processor with the lowest ID number that
passes self-test (STF line is +) becomes the boot processor, unless you
intervene. Using the SET CPU command and its qualifiers, you can
change the eligibility of the processors to become the boot processor
(see Section 5.18.2).
The results on the BPD line indicate:
•

The boot processor (B)

•

Processors eligible to become the boot processor (E)

•

Processors ineligible to become the boot processor (D)

This BPD line is printed twice. After the first determination of the
boot processor, the processors go through an extended test. Since
it is possible for a processor to pass self-test (at line STF) and fail
the extended test (at ETF), the processors again determine the boot
processor following the extended test.
In Figure 6–5 the processor at node 3 was chosen boot processor. Then
this processor failed the extended test, so the processor at node 4 was
chosen boot processor.

& During the extended test (ETF) all processors run additional CPU tests
involving memory. In Figure 6–5, results printed at this ETF line
indicate:

•

Two processors passed the extended test (+)

•

Two processors failed the extended test (–)

For vector processors, either an "E" or a "D" appears on both BPD lines. An "E" indicates
that the vector processor is enabled for use with system software; a "D" indicates that the
vector processor is disabled.

System Self-Test and Troubleshooting 6–11

6.6 Self-Test Lines ILV and Mb
The ILV line details the interleaving of the memories, and
the Mb line gives the Mbytes of each memory module and
the total size of system memory.
Figure 6–6: Self-Test Results: ILV and Mb
#123456789 0123456789 0123456789 0123456789 012345#
F

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

P
+
E
+
B

P
+
B
E

P
E
E

P
+
D
+
D

TYP
STF
BPD
ETF
BPD

.
.

B2
64

B1
64

A2
64

A1
64

.
.

ILV
256 Mb

Console = V1.00

RBDs = V1.00

EEPROM = 1.00/1.00

NODE #

SN = SGO1234567

>>>

msb-0701E-91

Passing Memory
The system configuration being tested is discussed in Section 6.2.

' This ILV line contains a memory interleave value (ILV) for each
memory. Each interleave set is indicated by a different letter.

In Figure 6–6, a SET MEMORY command was used to create two
interleaved sets of two 64-Mbyte memories each (see Section 5.18.4).
This is indicated by the memory modules at nodes 7 and 8 being in
the first interleave set A. Memories at nodes 9 and A are in memory
interleave set B. The SET MEMORY command was:
SET MEMORY /INTERLEAVE:(7+8, 9+A)

6–12 VAX 6000 Series Owner’s Manual

7
8

If the default interleave were set on this configuration, it would be one
4-way interleave (modules at nodes 7, 8, 9, and A):
>>> SET MEMORY /INTERLEAVE:DEFAULT
>>> INITIALIZE
>>> SHOW MEMORY
F
E
D
C
B
A
9
8
7
.
.
.
.
A4 A3
.
.
.
.
64 64
/INTERLEAVE:DEFAULT

A2
64

A1
64

.
.

NODE #
ILV
256 Mb

( The line after the ILV line displays the size of each configured memory
module and gives the total Mbytes of system memory. In Figure 6–6,
the total is 256 Mbytes.

Failing Memory
When a memory module does not pass its self-test, the boot processor tests
the memory and failing memory pages are noted. The console program
then puts the failing module in an interleave set by itself and maintains
the largest possible interleave set with the remaining modules. The failing
module is included in the configuration, but the addresses that failed selftest are not used. If the memory at node A failed self-test, it would be
included in the configuration, but would not be interleaved with node 9. A
SHOW MEMORY command shows the interleave with a failing module at
node A:
>>> SHOW MEMORY
F
E
D
C
B

.
.
.
.
C1 B1
.
.
.
.
64 64
/INTERLEAVE:(7+8, 9+A)

A2
64

A1
64

.
.

NODE #
ILV
256 Mb

Note that the /INTERLEAVE line above displays the interleave set as it is
stored in the EEPROM. The ILV line shows the configuration actually in
effect, including any changes due to self-test failures or incorrect interleave
lists.
To exclude a memory that is failing self-test, you use the SET MEMORY
command, without designating the node you want to exclude. In this
example, to exclude the memory at node A:
>>> SET MEMORY /INTERLEAVE:(7+8, 9)
>>> INITIALIZE
>>> SHOW MEMORY
F
E
D
C
B
A
9
8
7
6
.
.
.
.
B1
.
.
.
.
.
64
/INTERLEAVE:(7+8, 9)

A2
64

A1
64

.
.

NODE #
ILV
192 Mb

System Self-Test and Troubleshooting 6–13

6.7 Self-Test Identification Line
The last line of the self-test printout gives the console ROM
and RBD ROM version numbers, the EEPROM’s version
number and console patch level number, and the serial
number of the machine.

Figure 6–7: Self-Test Results: Identification Line
#123456789 0123456789 0123456789 0123456789 012345#
F

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

P
+
E
+
B

P
+
B
E

P
E
E

P
+
D
+
D

TYP
STF
BPD
ETF
BPD

.
.

B2
64

B1
64

A2
64

A1
64

.
.

ILV
256 Mb

Console = V1.00

RBDs = V1.00

EEPROM = 1.00/1.00
10

9
>>>

6–14 VAX 6000 Series Owner’s Manual

NODE #

SN = SGO1234567
11
msb-0701F-91

The information in the self-test identification line reflects what is in the
boot processor’s EEPROM.
The system configuration being tested is discussed in Section 6.2. See
Table 6–1.

) The console and RBD information indicates the version of read-only
memory that is installed on the processors. For Model 400 the console
version is called ROM0; the RBD version is called ROM1. For Model
300 only one ROM version is displayed.

Each processor has a console ROM and an RBD ROM; each ROM has
its own version. In Figure 6–7, all processors have version V1.00 ROM
resident. All processors should run with the same level of ROM. If your
processors have mixed levels of ROM, the ROM level of the primary
processor is displayed here, and you receive an error message that your
processors have different ROM levels. Contact your customer service
engineer to fix the ROM levels.

+> The EEPROM information gives the boot processor’s version of

EEPROM and the patch level. In Figure 6–7, the first number, 1.00,
gives the version of the contents of the EEPROM, and the second
number, 1.00, is the console patch level. If you run processors whose
EEPROMs do not match, you will receive an error message. Contact
your customer service engineer.

+? SN gives the system serial number. The system serial number is also
on the cabinet.

System Self-Test and Troubleshooting 6–15

6.8 Sample Self-Test Display with VAXBI Adapter
The self-test printout contains an additional line when an
optional VAXBI adapter is part of the system configuration.
The XBI line provides information on the node numbers and
self-test status for modules in the VAXBI card cages, which
are connected to the XMI through a DWMBB adapter.

Figure 6–8: Self-Test Results: TYP, STF, and XBI Lines
#123456789 0123456789 0123456789 0123456789 012345#
F

1
2

A
o
.
.
.

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

P
+
E
+
B

P
+
B
E

P
E
E

P
+
D
+
D

.
.

B2
64

B1
64

A2
64

A1
64

.
.

Console = V1.00

RBDs = V1.00

EEPROM = 1.00/1.00

>>>

6–16 VAX 6000 Series Owner’s Manual

NODE #
TYP
STF
BPD
ETF
BPD

XBI E + 3
ILV
256 Mb

SN = SGO1234567
msb-0701G-91

The system configuration shown in Figure 6–8 contains a DWMBB/A in
XMI slot E.

! The TYP line in this printout indicates that adapters in this
configuration are in XMI slots D and E.

" Because the DWMBB adapter does not have a module-resident self-test,
its entry for the STF line will always be "o".

# The test results for the DWMBB/A and DWMBB/B modules are

indicated on the XBI line, at the far right. In this example, the DWMBB
modules have passed self-test (XBI E +). The results of the VAXBI I/O
adapter self-tests are shown in columns 0 through F, which stand for
the VAXBI node numbers; in this configuration, node numbers 1, 2, 3,
4, and 6 are used. The adapter at node 3 failed its self-test.
When a DWMBB passes self-test, each node on that VAXBI is indicated
by symbols + and –, indicating the self-test status for that node number
on the VAXBI. A period (.) indicates that that node number is not used.
When a DWMBB fails self-test, the failure is reported, and the VAXBI
device self-tests are not displayed.

Note that XMI entries use slots 1 through E, while the VAXBI can have
entries in slots 0 through F. An XMI slot and node number are the same;
VAXBI slot and node numbers are not identical. Node plugs (labeled 1 to
12) in the VAXBI backplane are used to identify the number of a node.

System Self-Test and Troubleshooting 6–17

6.9 Troubleshooting During Booting
When booting fails, you can check several parameters.
Figure 6–9: Troubleshooting Booting

Enter
BOOT command

System
response
?

N
Check power

Self-test
completes

System
pass self-test
?

Force a boot
processor

Troubleshoot
failed
component

Boot
primitive works
?

Check error
message

Check boot
device (see
device manual)

System
boots
?
Y

I/O
program mode
msb-0017-90

6–18 VAX 6000 Series Owner’s Manual

If you need to load a boot primitive before booting, see Appendix E. If the
boot procedure fails, check through the steps shown in Figure 6–9.
1. Enter the BOOT command.
Was the console terminal in console mode? If you are using a nickname
(a stored BOOT command), did you use a valid nickname? You can
check the nickname by using the SHOW command (see Section 5.19).
2. System response?
If the system did not respond, check the power to the system. Turn
the system off and on again. Check the power indicator lights (see
Section 3.5) and console terminal connections. Check that the console
terminal is in console mode.
If the system still does not respond, try forcing a boot processor (see
Section 6.10).
3. Self-test completes.
You receive self-test printout. See Section 6.2 through Section 6.7 for a
full explanation of the self-test results.
4. System pass self-test?
If the system did not pass self-test, identify the modules that failed. If
the failed module is your designated boot processor and your terminal is
in console mode, use the SET CPU /NOPRIMARY command to reassign
the boot processor, and reboot.
If all system modules passed self-test, check your boot primitive.
5. Boot primitive works?
If the boot primitive is working, then the boot primitive program reads
the bootblock into memory and the system should boot. If the boot
primitive fails, the boot primitive program is not able to reach the boot
device. The console program displays several error messages. (Error
messages are explained in Appendix H and Appendix I.) Check to see
if the boot device passed self-test. Is the boot device connected to the
system? Is it powered up?
6. System boots?
If the system does not boot, check the boot device for malfunctioning.
See the disk or tape drive manual for the specific boot device. There
may also be a software failure. Check the boot device to be certain that
the bootblock is on the boot device.
If these steps fail, call your customer service engineer.

System Self-Test and Troubleshooting 6–19

6.10 Forcing a Boot Processor
The system may hang either because it cannot designate
a processor to be the boot processor, or because none
of the processors can find enough memory. When the
system is hung, the console does not respond. After you
check electrical and control panel connections, force a boot
processor.

Example 6–1: Forcing a Boot Processor
#123456789 0123456789 0123456
[ >>3 ]

! User enters ">>3" (not echoed), which forces the processor
! at node 3 to become the boot processor. System runs
! self-test and prints results.

A
+
.
.
.

.
.
.
.
.

M
+
.
.
.

.
.
.
.
.

P
+
B
+
B

P
+
D
+
D

P
E
E

TYP
STF
BPD
ETF
BPD

.
.

A4
64

A3
64

A2
64

A1
64

.
.

ILV
256 Mb

Console = V1.00
>>>

! Processor in slot 1 failed self-test
! at test 26. System hangs.

RBDs = V1.00

EEPROM = 1.00/1.00

NODE #

SN = SG01234567

! Console prompt appears. You are now in console mode.
! Not all console commands are available to you following
! the forcing of a boot processor.

6–20 VAX 6000 Series Owner’s Manual

If self-test fails after power-up or a system reset, the system may be hung
so that you cannot get a console prompt. The system hangs during the boot
process for one of two reasons:
•

No boot processor can be found. Processors either are disabled from
becoming the boot processor or they fail self-test.

•

No memory can be located.

Example 6–1 shows a case where no boot processor could be found.
Although there are three processors, two of the processors (at nodes 2
and 3) were made ineligible to become the boot processor (with the SET
CPU command and qualifiers). The third processor at node 1 is eligible to
be a boot processor, but it failed self-test. The system cannot find a boot
processor and hangs.
If the system hangs, after 60 seconds you can use the console program
to intervene. You can force a processor to become the boot processor and
override any previous commands by typing:
>>n

where n is the XMI node number of a processor. The console program then
makes this the boot processor. Self-test begins and processor n displays the
results of self-test. In Example 6–1 the processor at node 3 was forced to
become the boot processor. The >>n sequence is not echoed; you may have
to type this more than once to get to the console prompt.
Now you can examine the status of the processors by using the SHOW
CPU command. Self-test results do not give a true picture of the processor
status (BPD line), because you forced one of the processors to become the
boot processor. Only the SHOW CPU command gives the setting in the
EEPROM.
In Example 6–1, a next console action might be to SET CPU /PRIMARY
for the processors at nodes 2 and 3 to avoid repeating a processor lock. Not
all console commands are available to the system when you force a boot
processor, so it is useful to correct the cause of the system hang.
When a system hang is caused by inability to locate sufficient memory, the
processors cannot find memory as they attempt to run the extended test.
Partial self-test results are displayed and the following message:
?0047 Insufficient working memory for normal operation.

The system hangs here until the >>n command is entered. When a system
hang is caused by a memory problem and you force a boot processor, selftest results show that either all memory failed self-test or that no good
memory exists. Check the installation of your memories and restart the
system.

System Self-Test and Troubleshooting 6–21

6–22 VAX 6000 Series Owner’s Manual

Appendix A

Compact Disk Drive Instructions
The Ethernet-based InfoServer can house one or two RRD compact disk
drives. This appendix describes the RRD compact disk drive.

A.1 Controls and Indicators
The RRD compact disk drive has a green power light and a green activity
light. Table A–1 lists the functions of the lights shown in Figure A–1.

Figure A–1: RRD Compact Disk Drive

OPENING FOR
COMPACT DISK
ACTIVITY LIGHT
POWER LIGHT

msb-0481B-90

Compact Disk Drive Instructions A–1

Table A–1: RRD Light Summary
Light

State

Condition

Green
(Power)

Off
On

No power to drive
Power to drive

Green
(Activity)

Off
On
Blinking

No disk in drive
Disk is properly inserted into drive
Data is being transferred

A.2 Loading a Compact Disk
To load a disk, follow these steps:
1. Make sure the power light is on.
2. Insert the disk caddy into the drive, as shown in Figure A–2. Make
sure that the disk label is facing up and that the notches on the left
side of the caddy line up with the notches on the drive door.
3. Slide the caddy in as far as it will go and then remove it. The disk and
its housing remain in the drive.
4. The activity light should go on within 5 seconds.
If the activity light does not go on, the disk may be inserted incorrectly.
Unload the disk and then reload. If you think the disk is loaded
correctly, but the green light does not go on, try loading another disk
into the drive. If the new disk loads successfully, then the original disk
may be defective. Call your Digital customer service engineer.

A.3 Unloading a Compact Disk
Before unloading a disk, check to see that the disk is not transferring data
(activity light is not blinking). Do not unload if the disk is transferring
data. To unload a disk:
1. Position the transparent sleeve by making sure that the arrow on the
sleeve is pointing toward the drive.
2. Insert the sleeve all the way into the drive.
3. Remove the caddy. The disk and caddy will be in the sleeve. The
activity light goes off.

A–2 VAX 6000 Series Owner’s Manual

Figure A–2: Loading a Compact Disk

msb-0483A-91

Compact Disk Drive Instructions A–3

A.4 Cleaning Disks
The disk caddy consists of the disk, the disk housing, and the transparent
sleeve. The caddy should be taken apart only if the transparent sleeve
is damaged or if the disk requires cleaning. See the RRD42 Disc Drive
Owner’s Manual for cleaning instructions.

Figure A–3: Disk Caddy Parts
DISK
TRANSPARENT
SLEEVE

HOUSING

msb-0486-90

A–4 VAX 6000 Series Owner’s Manual

Appendix B

TF/TK Tape Drive Instructions
The tape drive holds one tape cartridge that contains the magnetic tape on
a single reel. When a tape cartridge is inserted, the tape is automatically
threaded onto a reel inside the drive. The tape must be entirely rewound
before the cartridge can be removed from the drive. Rewinding can take
up to 90 seconds.
The TF85 and TK70 can read data from a tape that was written by a TK50,
but they cannot overwrite a tape originally written by a TK50. A TK50,
however, cannot read data from a tape written by a TF85 or TK70.

TF/TK Tape Drive Instructions

B–1

B.1 Controls and Indicators
The tape drive has lights that indicate device operation, a beeper, an unload
button, and a cartridge insert/release handle. Table B–1 lists the functions
of TF85 tape drive controls and indicators that are shown in Figure B–1.

d
oa

U
nl

pe
r
H ate
an
dl
e

W
r
Pr i t e
ot
ec
Ta ted
pe
in
U
U
se
s
Ce
le
Ta an
pe ing

Figure B–1: TF85 Tape Drive

ORANGE

CARTRIDGE
INSERT/RELEASE
HANDLE

GREEN

Lo
To

YELLOW

W
O
Pr To
H Clo Ins H Op Wa
em Ha pe a
es
an s
e a e
U
s
n
ov ndl n t it
dl e t rt T ndl n t it
Bu loa
e h
e hi
e
ap e his
is
s
Ta
tto d
Li
e
gh
pe
n
t

ORANGE

Li
g

FRONT

msb-0766A-91

B–2 VAX 6000 Series Owner’s Manual

Table B–1: TF85 Light Summary
Light

State

Condition

Green
(Operate Handle)

On
Off
Blinking

OK to operate handle.
Do not operate handle.
Defective cartridge. Pull the handle to the open position and remove cartridge.
Try another cartridge.

Yellow
(Tape in Use)

Steady
Blinking

Drive ready.
Drive in use.

Orange 1
(Write Protected)

On
Off

Tape write protected.
Tape write enabled.

Orange
(Use Cleaning Tape)

On
Off

Drive needs cleaning.
Drive cleaning unnecessary.

All four lights

Blinking

Drive fault. Attempt to reset the fault by pressing the unload button.

1 This orange light is on when any of the following conditions exist:

Cartridge write protect switch is in the protected position.
 Cartridge is software write protected.
 Attempt was made to mount or initialize a cartridge previously written in a TK50 drive.

B.2 Loading a Tape
To load a tape, follow these steps:
1. When the green light is on steadily, pull the handle to the open position.
2. With the label facing out, insert the tape cartridge.
3. Push the cartridge in until it is completely inside the drive.
4. Push the handle to the closed position. The yellow light blinks,
indicating that the tape is loading. When the yellow light stays on
steadily, the drive is ready for use.
NOTE: If the green light blinks or if all lights blink, the loading has failed.

TF/TK Tape Drive Instructions

B–3

B.3 Unloading a Tape
To unload a tape, follow these steps:
1. Press the unload button or execute an appropriate operating system
unload command. The yellow light blinks as the tape rewinds.
2. When the green light turns on and the beep sounds, pull the handle to
the open position. The cartridge will partially eject.
3. Remove the cartridge.
4. Push the handle to the closed position.
NOTE: If all lights blink, the unload has failed.

B.4 Write-Protecting Your Tape Cartridge
Write-protecting a tape cartridge prevents accidental erasure of information
stored on the tape. To write-protect a tape, slide the tape’s write-protect
switch to the left so that the small orange rectangle is visible, as shown in
Figure B–2.

Figure B–2: Tape Cartridge

B–4 VAX 6000 Series Owner’s Manual

B.5 Labeling a Tape Cartridge
To label your tape cartridge:
•

Write your identifying information on the label. Note the recording
density: CompacTape III = 2.6 Gbytes.

•

Put the label into the slot on the front of the cartridge. See Figure B–2.

•

Use only the labels supplied with the tape cartridge. Stick-on labels
applied to the top, bottom, or sides of the cartridge can loosen and jam
or damage the tape drive.

•

Write only on the label. Do not write on the tape cartridge with a pen
or pencil.

B.6 Tape Handling and Storage Guidelines
To add life to your tapes and protect data, follow these guidelines:
•

Do not drop or bang the cartridge.

•

Store tape cartridges upright in a dust-free environment.

•

Keep tape cartridges away from direct sunlight, heaters, and other
sources of heat. Store tape cartridges in an even temperature between
10o and 40o C (50o to 104o F).

•

Keep tape cartridges away from sources of electromagnetic interference,
such as terminals, motors, and video or X-ray equipment.

TF/TK Tape Drive Instructions

B–5

Appendix C

Device Type Code Assignments
Table C–1 lists XMI device type codes. See Appendix D for VAXBI device
type codes. Device type code assignments are shown in the output of the
SHOW CONFIGURATION console command (see Section 5.19).

Table C–1: XMI Device Type Code Assignments
Code

Device

Function

2001

DWMBA/A

XMI-to-VAXBI adapter

2002

DWMBB/A

XMI-to-VAXBI adapter

2002

DWMVA/A

XMI-to-VMEbus adapter

4001

MS62A

Memory

4001

MS65A

Memory

8001

KA62A

Processor

8001

KA62B

Processor

8080

KA65A

Processor

8082

KA64A

Processor

8087

KA66A

Processor

0C03

DEMNA

XMI-to-NI adapter

0C05

CIXCD

XMI-to-CI adapter

0C22

KDM70

RA disk and TA tape interface

0810

KFMSA

RF disk and TF tape interface

0823

DEMFA

XMI-to-FDDI adapter

Device Type Code Assignments C–1

Appendix D

VAXBI Options and Adapters
This appendix describes VAXBI options and adapters available with a VAX
6000 series system.
VAXBI options are supported by the XMI-to-VAXBI adapter, called the
DWMBB adapter. The DWMBB adapter maps data between the XMI and
VAXBI buses. The VAXBI, in turn, passes data between the system and
peripheral devices. Up to six DWMBB adapters are supported.

D.1 Supported VAXBI Adapters
Table D–1 lists some of the VAXBI devices supported by VAX 6000 series
systems. Note that some VAXBI adapters have more than one module,
requiring more than one slot on the VAXBI.

Table D–1: VAXBI Adapters
Adapter

No.
Slots

Device
Code

CIBCA

0108

CI port interface; connects a system to a Star Coupler.

DEBNA

410F

Ethernet port interface; connects a system to the Ethernet.

DEBNI

0118

Ethernet port interface; connects a system to the Ethernet.

DHB32

0109

Communication device;
nals.

DMB32

0109

Interface for 8-channel asynchronous communications
for terminals, one synchronous channel, and a parallel port for a line printer.

DRB32

1 or 2

0101

Parallel port.

DSB32

010A

Two-channel synchronous communication device.

DWMBB/B

210F

VAXBI-to-XMI interface.

Function

supports up to 16 termi-

VAXBI Options and Adapters D–1

Table D–1 (Cont.): VAXBI Adapters
Adapter

No.
Slots

Device
Code

Function

KDB50

010E

DSA disk adapter; enables connection to disk drives.

RBV20/
RBV64

0103

Write-once optical drive controller; uses the KLESI–
B.

TBK50

410E

TK50 tape drive controller; connects the TK to the system.

TBK70

410B

TK70 tape drive controller; connects the TK to the system.

TM32

011F

Gapless tape controller.

TU81E

0103

TU81E controller; local (nonclustered) tape subsystem; uses the KLESI–B.

See Digital’s Systems and Options Catalog or the VAXBI Options Handbook
for more information on VAXBI adapters.

D.2 Supported Boot Devices
Table D–2 lists the boot devices supported by the VAXBI.

Table D–2: VAXBI Boot Devices
Device

Location

CI disk

Disk located on system’s HSC controller connected to the system by the CIBCA adapter on the VAXBI.

Ethernet disk

Disk connected to the system over the Ethernet, through the VAXBI and
DEBNI or DEBNA Ethernet port interface.

Local tape

TK50 or TK70 tape drive used as console load device; used for booting standalone backup.

Local disk

Disk connected to the system through the VAXBI; regular boot procedure specifies this disk as default boot device.

D–2 VAX 6000 Series Owner’s Manual

D.3 VAXBI Expander Cabinet
A VAXBI expander cabinet (Figure D–1) allows you to attach additional
VAXBI channels, each with its required DWMBB/B.
The cabinet holds one to four VAXBI card cages, each with its own power
supply. Two blowers cool the cabinet, and an AC power controller completes
the power system.
For instructions on installing the VAXBI expander cabinet, see the VAXBI
Expander Cabinet Installation Guide or the VAX 6000 Series Installation
Guide.

Figure D–1: VAXBI Expander Cabinet

COOLING
ASSEMBLY

1 TO 4 POWER
SUPPLY UNITS

154 CM
(60.5 IN)

1 TO 4 VAXBI
CARD CAGES

AC POWER
SUPPLY

76 CM
(30 IN)

msb-0161-88

VAXBI Options and Adapters D–3

D.4 Power for the VAXBI Option
Table D–3 lists the system power available for the 12-slot in-cabinet VAXBI
card cage.

Table D–3: In-Cabinet VAXBI Power
DC Voltage

Available
VAXBI Current

Note

+5V

130.0 A

Main logic

+5VBB

Connected to +5V

Not battery backed up

+12V

4.0 A

RS–232

–12V

2.4 A

RS–232

–5.2V

20.0 A

ECL logic

–2V

7.0 A

ECL logic

D–4 VAX 6000 Series Owner’s Manual

Appendix E

EVUCA Program
This appendix describes the EVUCA program, the VAX 6000 EEPROM
update utility. EVUCA allows you to:
•

Update a processor’s EEPROM contents

•

Load boot primitives

E.1 EVUCA Program Overview
The EVUCA program runs under the VAX Diagnostic Supervisor (VAX/DS)
in console mode. Table E–1 lists the processor-specific data files used to
update the EEPROM contents. Each data file consists of the latest patch
file for each major version of the PROM and all loadable boot primitives.
EEPROMs are also updated on secondary processors if they are selected
and attached under VAX/DS.

Table E–1: EEPROM Update Data Files
Data File

Processor

Model Number

EXUCA.BIN

KA66A

600

EMUCA.BIN

KA65A

500

ERUCA.BIN

KA64A

400

ELUCB.BIN

KA62B

300

ELUCA.BIN

KA62A

200

The following conditions must be met before running EVUCA:
•

All processors and memory modules must pass self-test.

•

Each processor must have console and diagnostic ROMs at the same
major revision level.

EVUCA Program E–1

E.2 Updating EEPROM Contents
Example E–1 shows a sample EEPROM update of a Model 600 twoprocessor system. The boot processor is in slot 1 of the XMI card cage
and the secondary processor is in slot 2.

! At the console prompt, boot VAX/DS.
" At the VAX/DS prompt, load the EVUCA program.
# Attach the boot processor.
$ Attach the secondary processor.
% Issue SELECT ALL to select all devices in the system configuration.

SET TRACE enables printing of test numbers and names when EVUCA
runs.

& Issue the START command to begin the EVUCA program.
' In this example the EXUCA.BIN data file is loaded to update KA66A
processors. The EVUCA program uses the data file that corresponds to
the processor type (see Table E–1). Press Return to continue.

( The EEPROM updates are verified.
) Exit VAX/DS.

E–2 VAX 6000 Series Owner’s Manual

Example E–1: Updating EEPROM Contents

>>> BOOT /XMI:n /R5:10 DUxx

[the VAX Diagnostic Supervisor banner appears]
DS> LOAD EVUCA

#
DS> ATTACH KA66A HUB KA1 2 $
DS> SELECT ALL %
DS> ATTACH KA66A HUB KA0 1

DS> SET TRACE

DS> START

.. Program: EVUCA - VAX 6000 EEPROM Update Utility, revision 2.0, 4
tests, at 00:05:57.61.
Testing: _KA0 _KA1
Node 02, booting.
Test 2: Load data from media
Data file to be loaded? <EXUCA.BIN>

! Model 600

Searching...
Load complete.
Update rev:

0200

Test 3: Determine typecodes updated
Test 4: Update EEPROM data
Creating new eeprom in memory.
Writing to EEPROM.
Verifying EEPROM on node 01
EEPROM rev:
0200

(

Verification complete on node 01
Secondaries are being updated, please wait maximum of 20 seconds.
Secondary CPU 02 Done.
Verification complete.
The primary was successfully updated.
Secondary CPU 02, was successfully updated.
.. End of run, 0 errors detected, pass count is 1,
time is 1-NOV-1991 00:07:05.94
DS> EXIT

)

>>>

EVUCA Program E–3

Appendix F

Control Flags for Booting
With the console BOOT command, you can control various phases of booting
by setting bits in General Purpose Register R5:
BOOT /R5:n

where n is in hexadecimal notation. For example, to set bit 4 in R5 when
booting, you would enter:
BOOT /R5:10

The R5 bit functions are defined by VMB and by the operating system. The
value –1 in R5 is reserved for Digital.

Table F–1: R5 Bit Functions for VMS
Bit

Function

Conversational boot. The secondary bootstrap program, SYSBOOT, prompts you
for system parameters at the console terminal.

Debug. If this flag bit is set, the operating system maps the code for the
XDELTA debugger into the system page tables of the running operating system.

Initial breakpoint. If this flag bit is set, VMS executes a breakpoint (BPT) instruction early in the bootstrapping process.

Secondary boot from boot block.
The secondary boot is a single 512byte block whose logical block number is specified in General Purpose Register R4.

Boots the VAX Diagnostic Supervisor. The secondary loader is an image called DIAGBOOT.EXE.

Boot breakpoint. This stops the primary and secondary loaders with a breakpoint (BPT) instruction before testing memory.

Control Flags for Booting F–1

Table F–1 (Cont.): R5 Bit Functions for VMS
Bit

Function

Image header.
The transfer address of the secondary loader image comes from the image header for that file. If this flag is not set, control shifts to the first byte of the secondary loader.

File name. VMB prompts for the name of a secondary loader.

Halt before transfer. VMB executes a HALT instruction before transferring control to the secondary loader.

No effect, since console program tests memory.

Reserved for the VAX Diagnostic Supervisor.

Do not discard CRD pages.

31:28

Specifies the top-level directory number for system disks.

Table F–2: R5 Bit Functions for ULTRIX
Bit

Function

Forces ULTRIXBOOT to prompt the user for an image name (the default is VMUNIX).

Boots the ULTRIX kernel image in single-user mode.

Must be set, and R4 must be zero.

Must be set.

F–2 VAX 6000 Series Owner’s Manual

Appendix G

Console Commands
Table G–1 gives a summary of the console commands. Chapter 5 gives a
full description of each command, its qualifiers, and examples.

Table G–1: Console Commands and Qualifiers
Command and
Qualifiers

Function

BOOT
/R3:n /R5:n
/XMI:n /BI:m
/NODE:n
/FILENAME:xyz
/DSSI_NODE:n
/PORT:x

Initializes the system,
gins the boot program.

causing a self-test,

and be-

CLEAR EXCEPTION

Cleans up error state in XBER, XBEER, and CPUspecific registers.

CONTINUE

Begins processing at the address where processing was interrupted by a CTRL/P console command.

DEPOSIT
/B /G /I /L /M
/N /P /Q /V
/VE /W

Stores data in a specified address.

EXAMINE
/B /G /I /L /M
/N /P /Q /V
/VE /W

Displays the contents of a specified address.

FIND
/MEMORY
/RPB

Searches main memory for a page-aligned 256-Kbyte block
of good memory or for a restart parameter block.

HALT

Null command; no action is taken since the processor has already halted in order to enter console mode.

HELP

Prints explanation of console commands.

Console Commands G–1

Table G–1 (Cont.): Console Commands and Qualifiers
Command and
Qualifiers

Function

INITIALIZE [n]
/BI:n

Performs a system reset, including self-test.

REPEAT

Executes the command passed as its argument.

SET BOOT

Stores a boot command by a nickname.

SET CPU [n]
/ENABLED
/ALL
/NOENABLED
/NEXT_PRIMARY
/PRIMARY
/ALL
/NOPRIMARY
/VECTOR_ENABLED
/NOVECTOR_ENABLED

Specifies eligibility of processors to become the boot processor or disables a vector processor.1

SET LANGUAGE
ENGLISH
INTERNATIONAL

Changes the output of the console error messages between
numeric code only (international mode) and code plus explanation (English mode).

SET MEMORY
/CONSOLE_LIMIT:n
/INTERLEAVE:(n+n...)
/INTERLEAVE:DEFAULT
/INTERLEAVE:NONE

Designates the method of interleaving the memory modules; supersedes the console program’s default interleaving.

SET TERMINAL
/BREAK
/NOBREAK
/HARDCOPY
/NOHARDCOPY
/SCOPE
/NOSCOPE
/SPEED:n

Sets console terminal characteristics.

SHOW ALL

Displays the current value of parameters set.

SHOW BOOT

Displays all boot commands and nicknames that have been
saved using SET BOOT.

SHOW CONFIGURATION

Displays the hardware device type and revision level for
each XMI and VAXBI node and indicates self-test status.

SHOW CPU

Identifies the primary processor and the status of other processors.

1 Vector processors are supported only on Model 400 and 500 systems.

G–2 VAX 6000 Series Owner’s Manual

Table G–1 (Cont.): Console Commands and Qualifiers
Command and
Qualifiers

Function

SHOW DSSI

Displays DSSI bus numbers, node numbers, and unit numbers.

SHOW ETHERNET

Displays Ethernet hardware addresses for all Ethernet adapters on the system and FDDI hardware addresses for all FDDI adapters.

SHOW FIELD2

Displays saved boot commands, console terminal parameters, console language mode, memory configuration, type of power system, and system serial number.

SHOW LANGUAGE

Displays the mode currently set for console error messages, international or English.

SHOW MEMORY

Displays the memory lines from the system self-test, showing interleave and memory size.

SHOW TERMINAL

Displays the baud rate and terminal characteristics functioning on the console terminal.

START

Begins execution of an instruction at the address specified in the command string.

STOP
/BI:n

Halts the specified node.

TEST
/RBD

Passes control to the self-test diagnostics.

UPDATE

Copies contents of the EEPROM on the processor executing the command to the EEPROM of another processor.

Logically connects the console terminal to another processor on the XMI bus or to a VAXBI node.

/BI:n
!

Introduces a comment.

2 The SHOW FIELD command is available only on Model 500 and 600 systems.

Console Commands G–3

Appendix H

Console Error Messages (Model 400
and Higher)
Table H–1 lists Model 400/500/600 messages that appear when the
processor halts and the console gains control. Most messages3 are followed
by:
•

PC = xxxxxxxx — program counter = address at which the processor
halted or the exception occurred

•

PSL = xxxxxxxx — processor status longword = contents of the register

•

–SP = xxxxxxxx — –SP is one of the following:
ESP executive stack pointer
ISP interrupt stack pointer
KSP kernel stack pointer
SSP supervisor stack pointer
USP user stack pointer

Table H–2 lists other console error messages that are common to Model 400
and higher systems. Table H–3 lists console error messages that apply only
to Models 500 and 600. Table H–4 lists console error messages unique to
Model 600.

3 On Model 400, system error messages and number codes appear as:

?nn <message>

Console Error Messages (Model 400 and Higher)

H–1

Table H–1: Console Error Messages Indicating Halt (Model 400
and Higher)
Error Message

Meaning

?0002 External halt (CTRL/P, break, or external halt).

CTRL/P

?0003 Power-up halt.

System has powered up, had a system reset, or an XMI node reset.

?0004 Interrupt stack not valid during exception processing.

Interrupt stack pointer contained an invalid address.

?0005 Machine check occurred during exception processing.

A machine check occurred while handling another error condition.

?0006 Halt instruction executed in kernel mode.

The CPU
tion.

?0007 SCB vector bits <1:0> = 11.

An interrupt or exception vector in the
System Control Block contained an invalid address.

?0008 SCB vector bits <1:0> = 10.

An interrupt or exception vector in the
System Control Block contained an invalid address.

?000A CHMx executed while on interrupt stack.

A change-mode instruction was issued
while executing on the interrupt stack.

?0010 ACV/TNV occurred during machine check
processing.

An access violation or translation-notvalid error occurred while handling another error condition.

?0011 ACV/TNV occurred during kernel-stacknot-valid processing.

An access violation or translation-notvalid error occurred while handling another error condition.

?0012 Machine check occurred during machine check processing.

A machine check occurred while processing a machine check.

?0013 Machine check occurred during kernelstack-not-valid processing.

A machine check occurred while handling another error condition.

?0019 PSL <26:24>= 101 during interrupt
or exception.

An exception or interrupt occurred while
on the interrupt stack but not in kernel mode.

?001A PSL <26:24>= 110 during interrupt
or exception.

An exception or interrupt occurred while
on the interrupt stack but not in kernel mode.

H–2 VAX 6000 Series Owner’s Manual

or STOP command.

executed

Halt

instruc-

Table H–1 (Cont.): Console Error Messages Indicating Halt (Model
400 and Higher)
Error Message

Meaning

?001B PSL <26:24>= 111 during interrupt
or exception.

An exception or interrupt occurred while
on the interrupt stack but not in kernel mode.

?001D PSL <26:24> = 101 during REI.

An REI instruction attempted to restore a PSL with an invalid combination of access mode and interrupt stack bits.

?001E PSL <26:24> = 110 during REI.

An REI instruction attempted to restore a PSL with an invalid combination of access mode and interrupt stack bits.

?001F PSL <26:24> = 111 during REI.

An REI instruction attempted to restore a PSL with an invalid combination of access mode and interrupt stack bits.

Table H–2: Standard Console Error Messages (Model 400 and
Higher)
Error Message

Meaning

?0020 Illegal memory reference.

An attempt was made to reference a virtual address (/V) that is either unmapped or is protected against access under the current PSL.

?0021 Illegal command.

The command was not recognized, contained the wrong number of parameters, or contained unrecognized or inappropriate qualifiers.

?0022 Illegal address.

The specified address was recognized as
being invalid, for example, a general purpose register number greater than 15.

?0023 Value is too large.

A parameter or qualifier value contained too many digits.

?0024 Conflicting qualifiers.

A command specified recognized qualifiers that are illegal in combination.

Console Error Messages (Model 400 and Higher)

H–3

Table H–2 (Cont.): Standard Console Error Messages (Model 400
and Higher)
Error Message

Meaning

?0025 Checksum did not match.

The checksum calculated for a block of X
command data did not match the checksum received.

?0026 Halted.

The processor is currently halted.

?0027 Item was not found.

The item requested in a FIND command could not be found.

?0028 Timeout while waiting for characters.

The X command failed to receive a full
block of data within the timeout period.

?0029 Machine check accessing memory.

Either the specified address is not implemented by any hardware in the system, or an attempt was made to write
a read-only address, for example, the address of the 33rd Mbyte of memory on a 32-Mbyte system.

?002A Unexpected machine check or
interrupt.

A valid operation within the console
caused a machine check or interrupt.

?002B Command is not implemented.

The command is not implemented by this
console.

?002C Unexpected exception.

An attempt was made to examine either a nonexistent IPR or an unimplemented register in RSSC address range
(20140000—20140800).

?002D For Secondary Processor n.

This message is a preface to second message describing some error related to a secondary processor. This message indicates which secondary processor is involved.

?002E Specified node is not an I/O adapter.

The referenced node is incapable of performing I/O or did not pass its selftest.

?0030 Write to Z command target has timed out.

The target node of the Z command is not
responding.

?0031 Z connection terminated by ^P.

A CTRL/P was typed on the
board to terminate a Z command.

?0032 Your node is already part of a Z
connection.

You cannot issue a Z command while executing a Z command.

H–4 VAX 6000 Series Owner’s Manual

key-

Table H–2 (Cont.): Standard Console Error Messages (Model 400
and Higher)
Error Message

Meaning

?0033 Z connection successfully started.

You have requested a Z connection to a
valid node.

?0034 Specified target already has a Z
connection.

The target node was the target of a previous Z connection that was improperly terminated. Reset the system to clear this
condition.

?0036 Command too long.

The command length exceeds 80 characters.

?0037 Bad explicit interleave list — configuring all arrays uninterleaved.

The list of memory arrays for explicit interleave includes no nodes that
are actually memory arrays.
All arrays found in the system are configured.

?0039 Console patches are not usable.

The console patch area in EEPROM
is corrupted or contains a patch revision that is incompatible with the console ROM.

?003B Error encountered during I/O
operation.

An I/O adapter returned an error status
while the console boot primitive was performing I/O.

?003C Secondary processor not in console mode.

The primary processor console needed to
communicate with a secondary processor, but the secondary processor was not
in console mode. STOP the node or reset the system to clear this condition.

?003D Error initializing I/O device.

A console boot primitive needed to perform I/O, but could not initialize the I/O
adapter.

?003E Timeout while sending message to
secondary processor.

A secondary processor failed to respond to a message sent from the primary.
The primary sends such messages to perform console functions on secondary processors.

?003F Microcode power-up self-test failed
in REX520.

Model 400 CPU chip failed its microcoded self-test.

?0040 Key switch must be at "Update" to
update EEPROM.

A SET command was issued, but the
key switch was not set to allow updates to the EEPROM.

Console Error Messages (Model 400 and Higher)

H–5

Table H–2 (Cont.): Standard Console Error Messages (Model 400
and Higher)
Error Message

Meaning

?0041 Specified node is not a bus adapter.

A command to access a VAXBI node specified an XMI node that was not a bus
adapter.

?0042 Invalid terminal speed.

The SET TERMINAL command specified an unsupported baud rate.

?0043 Unable to initialize node.

The INITIALIZE command failed to reset the specified node.

?0044 Processor is not enabled to BOOT or
START.

As a result of a SET CPU/NOENABLE
command, the processor is disabled from
leaving console mode.

?0045 Unable to stop node.

The STOP command failed to halt the
specified node.

?0046 Memory interleave set is
inconsistent: n n ...

The listed nodes do not form a valid memory interleave set.
One or more
of the nodes might not be a memory array or might be of a different size, or the set could contain an invalid number of members. Each listed array that is a valid memory will be configured uninterleaved.

?0047 Insufficient working memory for normal operation.

Less than 256 Kbytes per processor of
working memory were found. There is insufficient memory for the console to function normally or for the operating system to boot.

?0048 Uncorrectable memory errors—long memory test must be performed.

A Model 400 memory array contains
an unrecoverable error.
The console must perform a slow test to locate all the failing locations.

?0049 Memory cannot be initialized.

The specified operation was attempted
and prevented.

?004A Memories not interleaved due to
uncorrectable errors:

The listed arrays would normally have
been interleaved (by default or explicit request). Because one or more of them contained unrecoverable errors, this interleave set will not be constructed.

?004B Internal logic error in console.

The console encountered
cally impossible condition.

H–6 VAX 6000 Series Owner’s Manual

theoreti-

Table H–2 (Cont.): Standard Console Error Messages (Model 400
and Higher)
Error Message

Meaning

?004C Invalid node for Z command.

The target of a Z command must be a CPU
or an I/O adapter and must not be the primary processor.

?004D Invalid node for new primary.

The SET CPU command failed when attempting to make the specified node the
primary processor.

?004E Specified node is not a processor.

The specified node is not a processor, as required by the command.

?004F System serial number has not been
initialized.

No CPU in the system contains a valid
system serial number.

?0050 System serial number not initialized on
primary processor.

The primary processor has an uninitialized system serial number. All other processors in the system contain a valid serial number.

?0051 Secondary processor returned bad
response message.

A secondary processor returned an unintelligible response to a request made
by the console on the primary processor.

?0052 ROM revision mismatch. Secondary
processor has revision x.xx.

The revision of console ROM of a secondary processor does not match that of
the primary.

?0053 EEPROM header is corrupted.

The EEPROM header has been corrupted.
The EEPROM must be restored from the TK tape drive.

?0054 EEPROM revision mismatch.
Secondary processor has revision x.xx/y.yy.

A secondary processor has a different revision of EEPROM or has a different set of EEPROM patches installed.

?0055 Failed to locate EEPROM area.

The EEPROM did not contain a set of
data required by the console. The EEPROM may be corrupted.

?0056 Console parameters on secondary processor do not match primary.

The console parameters are not the same
for all processors .

?0057 EEPROM area checksum error.

A portion of the EEPROM is corrupted.
It may be necessary to reload the EEPROM from the TK tape drive.

Console Error Messages (Model 400 and Higher)

H–7

Table H–2 (Cont.): Standard Console Error Messages (Model 400
and Higher)
Error Message

Meaning

?0058 Saved boot specifications on secondary
processor do not match primary.

The saved boot specifications are not the
same for all processors.

?0059 Invalid unit number.

A BOOT or SET BOOT command specified a unit number that is not a valid hexadecimal number between 0 and FF.

?005A System serial number mismatch.
Secondary processor has xxxxxxxx.

The indicated serial number of a secondary processor does not match that of
the primary.

?005B Unknown type of boot device.

The console program does not have a boot
primitive to support the specified type
of device or the device could not be accessed to determine its type.

?005C No HELP is available.

The HELP command is not supported
when the console language is set to International.

?005D No such boot spec found.

The specified boot specification was not
found in the EEPROM.

?005E Saved boot spec table full.

The maximum number of saved boot specifications has already been stored.

?005F EEPROM header version mismatch.

Processors have different versions of EEPROMs.

?0061 EEPROM header or area has bad
format.

All or part of the EEPROM contains inconsistent data and is probably corrupted. Reload the EEPROM from the TK
tape.

?0062 Illegal node number.

The specified node number is invalid.

?0063
vice.

Unable

locate

console

tape

de-

The console could not locate the I/O
adapter that controls the TK tape.

?0064 Operation only applies to secondary
processors.

The command can only be directed at a
secondary processor.

?0065 Operation not allowed from secondary
processor.

A secondary processor cannot perform this
operation.

?0066 Validation of EEPROM tape image failed.

The image on tape is corrupted or
is not the result of a SAVE EEPROM command. The image cannot be restored.

H–8 VAX 6000 Series Owner’s Manual

Table H–2 (Cont.): Standard Console Error Messages (Model 400
and Higher)
Error Message

Meaning

?0067 Read of EEPROM image from tape failed.

The EEPROM image was not successfully read from tape.

?0068 Validation of local EEPROM failed.

For a PATCH EEPROM operation, the
EEPROM must first contain a valid image before it can be patched. For a RESTORE EEPROM operation, the image was written back to EEPROM
but could not be read back successfully.

?0069 EEPROM not changed.

The EEPROM contents were not changed.

?006A EEPROM changed successfully.

The EEPROM contents were successfully patched or restored.

?006B Error changing EEPROM.

An error occurred in writing to the EEPROM. The EEPROM contents may be corrupted.

?006C EEPROM saved to tape successfully.

The EEPROM contents were successfully written to the TK tape.

?006D EEPROM not saved to tape.

The EEPROM contents were not completely written to the TK tape.

?006E EEPROM Revision = x.xx/y.yy.

The EEPROM contents are at revision x.xx with revision y.yy patches.

?006F Major revision mismatch between tape
image and EEPROM.

The major revision of tape and EEPROM do not match. The requested operation cannot be performed.

?0070 Tape image Revision = x.xx/y.yy.

The EEPROM image on the TK tape is
at revision x.xx with revision y.yy patches.

?0073 System serial number updated.

The EEPROM has been updated with the
correct system serial number.

?0074 System serial number not updated.

The EEPROM has not been changed.

?0075 /CONSOLE_LIMIT value too small for
proper operation. Value ignored.

No change has been made.

?0076 Error writing to tape. Tape may be
write-locked.

Tape has not been written. Check to see
if tape is write-locked.

Console Error Messages (Model 400 and Higher)

H–9

Table H–2 (Cont.): Standard Console Error Messages (Model 400
and Higher)
Error Message

Meaning

?0077 CCA not accessible or corrupted.

Attempt to find the console communications area (CCA) failed.
The console then builds a local CCA, which does
not allow for interprocessor communication.

?0078 Vector module configuration error at node
n

The console detected a vector module configuration error. Problem can be that the
vector node number is not one greater
than the scalar CPU or that the module to the left of a vector processor is not a memory module.

?0079 Vector synchronization error.

The console could not synchronize with
the vector processor on a console entry. The Busy bit in the Vector Processor Status Register remained set after a timeout, or a vector processor error occurred.

?007A No vector module associated with CPU
at specified node.

No vector module is in the slot to the left
of the specified CPU, or the VIB cable either is not attached or is bad.

?007B An error occurred while accessing the vector module.

Attempt to access VCR, VLR, or VMR registers failed.

?007C I/O adapter configuration error at node
n

The I/O adapter at node n is configured improperly.

?007D Vector module is disabled—check KA64A
revision at XMI node n

The vector module is attached to a KA64A
module that is not at the revision level required.

?0083 Loading system software.1

The console is attempting to load the operating system in response to a BOOT command, power-up, or restart failure.

?0084 Failure.1

An operation did not complete successfully. Should be issued with another message to clarify failure.

?0085 Restarting system software.1

The console is attempting to restart the inmemory copy of the operating system following a power-up or serious error.

1 No numbered prefix appears with these messages in English language mode.

bers are used for these messages in International mode.

H–10 VAX 6000 Series Owner’s Manual

These num-

Table H–2 (Cont.): Standard Console Error Messages (Model 400
and Higher)
Error Message

Meaning

?00A0 Initializing system.1

The console is resetting the system in response to a BOOT command.

?00A1 Now updating the EEPROM of node n1

The console is updating the EEPROM.

?00A6 Console halting after unexpected machine check or exception.1

The console executed a Halt instruction to reset the console state after processing an unexpected machine check.

?00A7 RCSR <WD> is set. Local CCA must be
built.1

When the <WD> bit is set, writes to memory are disabled. The Model 400 processor must then build a CCA in local memory. Main memory cannot be written to or accessed with interlocked instructions.

?00A8 Bootstrap failed due to previous error.1

The previous attempt to bootstrap the system failed.

?00A9 Restart failed due to previous error.1

The previous attempt to restart the system failed.

Node n: ?xxxx

Error message ?xxxx was generated on secondary processor n and was passed
to the primary processor to be displayed.

1 No numbered prefix appears with these messages in English language mode.

These num-

bers are used for these messages in International mode.

Console Error Messages (Model 400 and Higher)

H–11

Table H–3: Console Error Messages for Models 500 and 600
Error Message

Meaning

?0104 Filename format error.

Period and semicolon characters are improperly used within the filename specified for a MOP boot.

?0105 Illegal character(s) in filename.

For filename specified in a MOP boot.

?0106 Filename cannot contain nested blanks or
tabs.

For filename specified in a MOP boot.

?0107 Filename can be no longer than 16 characters.

For filename specified in a MOP boot.

?0111 Microcode power-up self-test failed in
DC595.

Model 500 CPU chip failed its microcoded self-test.

?011E Uncorrectable memory errors discovered long memory test must be performed on node n

Memory array in node n contains an uncorrectable error. The console must perform a full test to locate all the failing locations.

?0120 Unsupported memory module found, will
not be configured.

One or more MS62A memory modules are installed but will not be used.
Only MS65A memory modules are compatible with Model 500 and higher.

?0121 Patch command no longer implemented—
use the Diagnostic utility EVUCA.

An invalid PATCH command was issued; use the EVUCA program to update the EEPROM.

Table H–4: Console Error Messages Unique to Model 600
?0201 One or more power-up tests have been bypassed.

A test normally run by the processor at power-up has been bypassed.

?0203 Hardware compatibility group mismatch—
secondary/primary: x/y.

Indicates hardware version mismatches
between the primary CPU and an indicated secondary CPU.

?0205 Error locating ROM boot code, run diagnostics.

Indicates a hardware problem
ing the CPU’s ROM code.

?0206 EEPROM in error or contains unsupported PCS, processor disabled.

Indicates an out of rev or faulty EEPROM image.
Use the EVUCA program to upgrade the EEPROM for the indicated CPU.

H–12 VAX 6000 Series Owner’s Manual

read-

Appendix I

Console Error Messages for Model 300
Table I–1 lists messages ?02 through ?1F which appear when the processor
halts and the console gains control. Each message is followed by a "PC =
xxxxxxxx" message giving the address where the processor was executing
when it halted; these messages designate the reasons for the halt.
Table I–2 lists the standard console error messages ?20 through ?7C.

Table I–1: Model 300 Console Error Messages Indicating Halt
Error Message

Meaning

?02 External halt.

CTRL-P

?04 Interrupt stack not valid.

Interrupt stack pointer contained an invalid address.

?05 Machine check during exception.

A machine check occurred while handling another error condition.

?06 Halt instruction executed.

The CPU
tion.

?07 SCB vector bits <1:0> = 11.

An interrupt or exception vector in the
System Control Block contained an invalid address.

?08 SCB vector bits <1:0> = 10.

An interrupt or exception vector in the
System Control Block contained an invalid address.

?0A CHMx executed while on interrupt stack.

A change-mode instruction was issued
while executing on the interrupt stack.

?0B CHMx to interrupt stack.

The System Control Block vector for a
change-mode instruction indicated service on the interrupt stack.

?0C SCB read error.

The System Control Block was not accessible in memory.

?10 ACV or TNV during machine check.

An access violation or translation-notvalid error occurred while handling another error condition.

or STOP command.

executed

Halt

instruc-

Console Error Messages for Model 300 I–1

Table I–1 (Cont.): Model 300 Console Error Messages Indicating Halt
Error Message

Meaning

?11 ACV or TNV during KSP not valid.

An access violation or translation-notvalid error occurred while handling another error condition.

?12 Machine check during machine check.

A machine check occurred while handling another error condition.

?13 Machine check during KSP not valid.

A machine check occurred while handling another error condition.

?19 PSL <26:24>= 101 during interrupt
or exception.

An exception or interrupt occurred while
on the interrupt stack but not in kernel mode.

?1A PSL <26:24>= 110 during interrupt
or exception.

An exception or interrupt occurred while
on the interrupt stack but not in kernel mode.

?1B PSL <26:24>= 111 during interrupt
or exception.

An exception or interrupt occurred while
on the interrupt stack but not in kernel mode.

?1D PSL <26:24> = 101 during REI.

An REI instruction attempted to restore a PSL with an invalid combination of access mode and interrupt stack bits.

?1E PSL <26:24> = 110 during REI.

An REI instruction attempted to restore a PSL with an invalid combination of access mode and interrupt stack bits.

?1F PSL <26:24> = 111 during REI.

An REI instruction attempted to restore a PSL with an invalid combination of access mode and interrupt stack bits.

I–2 VAX 6000 Series Owner’s Manual

Table I–2: Model 300 Standard Console Error Messages
Error Message

Meaning

?20 Illegal memory reference.

An attempt was made to reference a virtual address (/V) that is either unmapped or is protected against access under the current PSL.

?21 Illegal command.

The command was not recognized, contained the wrong number of parameters, or contained unrecognized or inappropriate qualifiers.

?22 Illegal address.

The specified address was recognized as
being invalid, for example, a general purpose register number greater than 15.

?23 Value is too large.

A parameter or qualifier value contained too many digits.

?24 Conflicting qualifiers.

A command specified recognized qualifiers that are illegal in combination.

?25 Checksum did not match.

The checksum calculated for a block of X
command data did not match the checksum received.

?26 Halted.

The processor is currently halted.

?27 Item was not found.

The item requested in a FIND command could not be found.

?28 Timeout while waiting for characters.

The X command failed to receive a full
block of data within the timeout period.

?29 Machine check accessing memory.

?2A Unexpected machine check or
interrupt.

A valid operation within the console
caused a machine check or interrupt.

?2B Command is not implemented.

The command is not implemented by this
console.

?2C Unexpected exception.

A valid operation within the console
caused an exception.

Console Error Messages for Model 300 I–3

Table I–2 (Cont.): Model
sages

300 Standard

Console Error

Mes-

Error Message

Meaning

?2D For Secondary Processor n

This message is a preface to second message describing some error related to a secondary processor. This message indicates which secondary processor is involved.

?2E Specified node is not an I/O adapter.

The referenced node is incapable of performing I/O or did not pass its selftest.

?30 Write to Z command target has timed out.

The target node of the Z command is not
responding.

?31 Z connection terminated by ^P.

A CTRL/P was typed on the
board to terminate a Z command.

?32 Your node is already part of a Z connection.

You cannot issue a Z command while executing a Z command.

?33 Z connection successfully started.

You have requested a Z connection to a
valid node.

?34 Specified target already has a Z connection.

The target node was the target of a previous Z connection that was improperly terminated. Reset the system to clear this
condition.

?36 Command too long.

The command length exceeds 80 characters.

?37 Explicit interleave list is bad.
Configuring all arrays uninterleaved.

The list of memory arrays for explicit interleave includes no nodes that
are actually memory arrays.
All arrays found in the system are configured.

?38 Waiting for a CR to terminate the command.

The command has not yet been issued by a carriage return.

?39 Console patches are not useable.

The console patch area in EEPROM
is corrupted or contains a patch revision that is incompatible with the console ROM.

?3B Error
tion.

encountered

during

I/O

opera-

I–4 VAX 6000 Series Owner’s Manual

key-

An I/O adapter returned an error status
while the console boot primitive was performing I/O.

Table I–2 (Cont.): Model
sages

300 Standard

Console Error

Mes-

Error Message

Meaning

?3C Secondary processor not in console mode.

The primary processor console needed to
communicate with a secondary processor, but the secondary processor was not
in console mode. STOP the node or reset the system to clear this condition.

?3D Error initializing I/O device.

A console boot primitive needed to perform I/O, but could not initialize the I/O
adapter.

?3E Timeout while sending message to
secondary.

A secondary processor failed to respond to a message sent from the primary.
The primary sends such messages to perform console functions on secondary processors.

?3F Key switch must be at "Update" to
update EEPROM.

A SET command needs to update the EEPROM, but the key switch is not set to allow updates.

?40 Specified node is not a bus adapter.

A command that accesses a VAXBI node
specified an XMI node that was not a bus
adapter.

?41 Invalid terminal speed.

The SET TERMINAL command specified an unsupported baud rate.

?42 Unable to initialize node.

The INITIALIZE command failed to reset the specified node.

?43 Processor is not enabled to BOOT or START.

As a result of a SET CPU/NOENABLE
command, the processor is disabled from
leaving console mode.

?44 Unable to stop node.

The STOP command failed to halt the
specified node.

?45 Memory interleave set is
inconsistent: n n ...

The listed nodes do not form a valid memory interleave set.
One or more of
the nodes might not be a memory array, or the set could contain an invalid number of members. Each listed array that is a valid memory will be configured uninterleaved.

Console Error Messages for Model 300 I–5

Table I–2 (Cont.): Model
sages

300 Standard

Console Error

Mes-

Error Message

Meaning

?46 Insufficient working memory for normal operation.

Less than 256 Kbytes per processor of
working memory were found. There is insufficient memory for the console to function normally or for the operating system to boot.

?47 Uncorrectable memory errors—long memory test must be performed.

A memory array contains an unrecoverable error.
The console must perform a slow test to locate all the failing locations.

?49 Memories not interleaved due to
uncorrectable errors:

The listed arrays would normally have
been interleaved (by default or explicit request). Because one or more of them contained unrecoverable errors, this interleave set will not be constructed.

?4A Internal logic error in console.

The console encountered
cally impossible condition.

?4B Invalid node for Z command.

The target of a Z command must be a CPU
or an I/O adapter and must not be the primary processor.

?4C Invalid node for new primary.

The SET CPU command failed when attempting to make the specified node the
primary processor.

?4D Specified node is not a processor.

The specified node is not a processor, as required by the command.

?4E System serial number has not been
initialized.

No CPU in the system contains a valid
system serial number.

?4F System serial number not initialized on
primary processor.

The primary processor has an uninitialized system serial number. All other processors in the system contain a valid serial number.

?50 Secondary processor returned bad
response message.

A secondary processor returned an unintelligible response to a request made
by the console on the primary processor.

?51 ROM revision mismatch. Secondary
processor has revision x.y.

The revision of console ROM of a secondary processor does not match the primary.

I–6 VAX 6000 Series Owner’s Manual

theoreti-

Table I–2 (Cont.): Model
sages

300 Standard

Console Error

Mes-

Error Message

Meaning

?52 EEPROM header is corrupted.

The EEPROM header has been corrupted.
The EEPROM must be restored from the TK tape drive.

?53 EEPROM revision mismatch.
Secondary processor has revision x.y/x.y.

A secondary processor has a different revision of EEPROM or has a different set of EEPROM patches installed.

?54 Failed to locate EEPROM area.

The EEPROM did not contain a set of
data required by the console. The EEPROM may be corrupted.

?55 Console parameters on secondary processor do not match primary.

Console parameters do not match on the
primary and secondary processors.

?56 EEPROM area checksum error.

A portion of the EEPROM is corrupted.
It may be necessary to reload the EEPROM from the TK tape drive.

?57 Saved boot specifications on secondary processor do not match primary.

Saved boot specifications do not match
on the primary and secondary processors.

?58 Invalid unit number.

A BOOT or SET BOOT command specifies a unit number that is not a valid hexadecimal number between 0 and FF.

?59 System serial number mismatch.
Secondary processor has xxxxxxxx.

The indicated serial number of a secondary processor does not match the primary.

?5A Unknown type of boot device.

The console program does not have a boot
primitive to support the specified type
of device or the device could not be accessed to determine its type.

?5B No HELP is available.

The HELP command is not supported
when the console language is set to International.

?5C No such boot spec found.

The specified saved boot specification was
not found in the EEPROM.

?5D Saved boot spec table full.

The maximum number of saved boot specifications has already been stored.

Console Error Messages for Model 300 I–7

Table I–2 (Cont.): Model
sages

300 Standard

Console Error

Mes-

Error Message

Meaning

?5E EEPROM header version mismatch.

The primary and a secondary processor have different versions of the EEPROM. The requested operation cannot be performed.

?5F Bad transfer length.

The primary processor attempted to send
EEPROM data to a secondary processor using an invalid length.

?60 EEPROM header or area has
bad format.

All or part of the EEPROM contains inconsistent data and is probably corrupted. Reload the EEPROM from the TK
tape.

?61 Illegal node number.

The specified node number is invalid.

?62 Unable to locate console tape device.

The console could not locate the I/O
adapter that controls the TK tape.

?63 Operation only applies to secondary
processors.

The command can only be directed at a
secondary processor.

?64 Insufficient memory to buffer EEPROM
image.

The SAVE, RESTORE, and PATCH EEPROM commands require working memory, but not enough was found.

?65 Validation of EEPROM tape image failed.

The image on tape is corrupted or
is not the result of a SAVE EEPROM command. The image cannot be restored.

?66 Read of EEPROM image from tape failed.

The EEPROM image was not successfully read from tape.

?67 Validation of local EEPROM failed.

?68 EEPROM not changed.

The EEPROM contents were not changed.

?69 EEPROM changed successfully.

The EEPROM contents were successfully patched or restored.

I–8 VAX 6000 Series Owner’s Manual

Table I–2 (Cont.): Model
sages

300 Standard

Console Error

Mes-

Error Message

Meaning

?6A Error changing EEPROM.

An error occurred in writing to the EEPROM. The EEPROM contents may be corrupted.

?6B EEPROM saved to tape successfully.

The EEPROM contents were successfully written to the TK tape.

?6C EEPROM not saved to tape.

The EEPROM contents were not completely written to the TK tape.

?6D EEPROM Revision = x.x/y.y.

The EEPROM contents are at revision x.x with revision y.y patches.

?6E Major revision mismatch between tape
image and EEPROM.

The TK tape contains an EEPROM image with a major revision different from
that found in the EEPROM. The image cannot be restored.

?6F Tape image Revision = x.x/y.y.

The EEPROM image on the TK tape is
at revision x.x with revision y.y patches.

?74

CONSOLE_LIMIT value too small for
proper operation. Value ignored.

?75

Error writing to tape. Tape may be writelocked.

?83

See Loading system software below.

?84

See Failure below.

?85

See Restarting system software below.

?B0

See Initializing system below.

Failure.

The console failed in a restart or boot operation. Shows as ?84 in SET LANGUAGE INTERNATIONAL mode.

Initializing system.

The console is resetting the system in response to a BOOT command.
Shows
as ?B0 in SET LANGUAGE INTERNATIONAL mode.

Console Error Messages for Model 300 I–9

Table I–2 (Cont.): Model
sages

300 Standard

Console Error

Mes-

Error Message

Meaning

Loading system software.

The console is attempting to load the operating system in response to a BOOT command, power-up, or restart failure. Shows
as ?83 in SET LANGUAGE INTERNATIONAL mode.

Node: n ?xx

Error message ?xx was generated on secondary processor n and was passed
to the primary processor to be displayed.

Restarting system software.

The console is attempting to restart the inmemory copy of the operating system following a power-up or serious error. Shows as ?85 in SET LANGUAGE INTERNATIONAL mode.

I–10 VAX 6000 Series Owner’s Manual

Appendix J

Boot Status and Error Messages
(Models 500 and 600)
This appendix lists status and error messages for Ethernet boots, local disk
and tape boots, and cluster boots (Models 500 and 600). Status messages
are shown in the order they would appear after the boot command is issued.
Listed after each status message are the error messages that could appear
during each boot subprocess.

J.1 Ethernet Boot Messages
1. [Start boot]
?002E Specified node is not an I/O adapter
?0100 Specified adapter failed self-test
?010B Illegal adapter specified for NI boot
2. * Initializing adapter
?0119 Failure to initialize specified adapter
3. * Specified adapter initialized successfully
4. * "Request Program" MOP message sent—waiting for service from
remote node
?0113 No traffic was detected on the Ethernet—aborting boot
procedure
?0115 Aborting boot process—adapter failed attempting to execute
port command
?011F Aborting boot process—adapter failed attempting to execute
boot command
5. * Still waiting for assistance—reissuing "Request Program" message
6. * Remote service link established
7. * Reading boot image from remote node
?010F Failed to receive image from remote server

Boot Status and Error Messages (Models 500 and 600)

J–1

8. * Passing control to transfer address

J.2 Local Disk Boot Messages
1. [Start Boot]
?002E Specified node is not an I/O adapter
?0100 Specified adapter failed self-test
?010A Illegal adapter specified for disk boot
2. * Initializing adapter
?0119 Failure to initialize specified adapter
3. * Specified adapter initialized successfully
4. * Connecting to boot disk or
* Reading bootblock from disk
?0102 Controller error detected—aborting
?0103 Drive error detected—aborting
?010E Specified unit offline — No media mounted or disabled via
RUN/STOP switch setting
?0114 Serious exception reported—aborting
?0116 Specified unit is inoperative
?0117 Specified unit offline
?0118 Specified unit offline—Unit unknown, online to another
controller or port disabled via A,B switches
5. * Passing control to transfer address

J.3 Local Tape Boot Messages
1. [Start boot]
?002E Specified node is not an I/O adapter
?0100 Specified adapter failed self-test
?010C Illegal adapter specified for tape use
2. * Initializing adapter
?0119 Failure to initialize specified adapter
3. * Specified adapter initialized successfully
4. * Connecting to tape or
* Reading bootblock from tape or

J–2 VAX 6000 Series Owner’s Manual

* Rewinding tape
?0101 BVP port error reported—aborting
?0102 Controller error detected—aborting
?0103 Drive error detected—aborting
?010E Specified unit offline—No media mounted or disabled via
RUN/STOP switch setting
?0114 Serious exception reported—aborting
?0116 Specified unit is inoperative
?0117 Specified unit offline
?0118 Specified unit offline—Unit unknown, online to another
controller or port disabled via A,B switches
5. * Passing control to transfer address

J.4 CI and DSSI Boot Messages
1. [Start boot]
?002E Specified node is not an I/O adapter
?0109 Illegal adapter specified for CI boot
?011A Illegal adapter specified for DSSI boot
2. * Initializing adapter
?0119 Failure to initialize specified adapter
3. * Specified adapter initialized successfully
4. * Connecting to storage controller
5. * Previous operation failed—retrying CI boot
6. * Previous operation failed—retrying DSSI boot
7. * Port received a "no path" error—retrying the init sequence
?0110 Port received a "no path" error after 6 retries—aborting the
boot process
8. * Connecting to MSCP server layer
9. * Previous operation failed—retrying CI boot
10. * Connecting to boot disk or
* Connecting to shadow unit—will fail over to physical after 6
attempts.
?0102 Controller error detected—aborting
?0103 Drive error detected—aborting

Boot Status and Error Messages (Models 500 and 600)

J–3

?010E Specified unit offline—No media mounted or disabled via
RUN/STOP switch setting
?0114 Serious exception reported—aborting
?0116 Specified unit is inoperative
?0117 Specified unit offline
?0118 Specified unit offline—Unit unknown, online to another
controller or port disabled via A,B switches
11. * Failure to connect to shadow unit—retrying on physical unit
12. * Reading bootblock from disk
?0102 Controller error detected—aborting
?0103 Drive error detected—aborting
?010E Specified unit offline—No media mounted or disabled via
RUN/STOP switch setting
?0114 Serious exception reported—aborting
?0116 Specified unit is inoperative
?0117 Specified unit offline
?0118 Specified unit offline—Unit unknown, online to another
controller or port disabled via A,B switches
13. * Passing control to transfer address

J–4 VAX 6000 Series Owner’s Manual

Glossary
Adapter

A node that interfaces other buses, communication lines, or peripheral
devices to the XMI bus or the VAXBI bus.
Address space

The 1 terabyte of physical address space that the XMI bus is capable of
supporting; currently the XMI bus supports 1 gigabyte of physical memory.
Asymmetric multiprocessing

A multiprocessing configuration in which the processors are not equal in
their ability to execute operating system code. In general, a single processor
is designated as the primary, or master, processor; other processors are
the slaves. The slave processors are limited to performing certain tasks,
whereas the master processor can perform all system tasks. Contrast with
Symmetric multiprocessing.
Bandwidth

The data transfer rate measured in information units transferred per unit
of time (for example, Mbytes per second).
Boot device

Contains the bootblock and typically also contains the virtual memory boot
program (VMB). A VAX 6000 series system can be booted from one of four
boot devices: the console load device, a local system disk, a disk connected
to the system through a CI adapter, or a disk connected to the system
through the Ethernet.
Boot primitives

Small programs stored in ROM on each processor with the console program.
Boot primitives read the bootblock from boot devices. There is a boot
primitive for each type of boot device.
Boot processor

The CPU module that boots the operating system and communicates with
the console.

Glossary–1

Bootblock

Block zero on the system disk; it contains the block number where the
virtual memory boot (VMB) program is located on the system disk and
contains a program that, with the boot primitive, reads VMB from the
system load device into memory.
CIBCA

VAXBI CI port interface; connects a system to a Star Coupler.
CIXCD

XMI CI port interface; connects a system to a Star Coupler.
Cold start

An attempt by the primary processor to boot a new copy of the operating
system.
Compact disk server

Ethernet-based CD server; provides access to CD-ROMs for software
installation, diagnostics, and on-line documentation.
Console communications area (CCA)

Segment of system main memory reserved by the console program.
Console mode

A mode of operation where the processor is not running the operating
system but allows a console terminal operator to communicate with nodes
on the XMI bus.
DEBNI

VAXBI adapter; Ethernet port interface.
DEMFA

XMI adapter to the FDDI (fiber distributed data interface).
DEMNA

XMI adapter; Ethernet port interface.
DHB32

VAXBI adapter communication device; supports up to 16 terminals.
DMB32

VAXBI adapter interface for 8-channel asynchronous communications for
terminals, one synchronous channel, and a parallel port for a line printer.

Glossary–2

DRB32

VAXBI adapter; parallel port.
DSB32

VAXBI adapter communication device; provides two synchronous lines.
DSSI

Digital Storage System Interconnect. A Digital Storage Architecture
interconnect used by the KFMSA adapter and RF and TF series integrated
storage elements to transfer data and to communicate with each other.
DWMBB

The XMI-to-VAXBI adapter; a 2-module adapter that allows data transfer
from the XMI to the VAXBI; DWMBB/A is the module in the XMI card cage,
and DWMBB/B is the VAXBI module. Every VAXBI on a VAX 6000 series
system must have a DWMBB adapter.
Ethernet-based compact disk server

The RRD compact disk drive, a console load device, functions as a server
on the Ethernet.
FV64A

Vector processor; works in a scalar/vector processor pair.
Interleaving memory

See Memory interleaving.
KDB50

VAXBI adapter for RA disks; enables connection to disk drives.
KDM70

XMI adapter for RA disks; enables connection to disk drives.
KFMSA

XMI adapter for RF disks and TF tapes; enables connection to nodes on a
DSSI bus. Each KFMSA adapter supports two DSSI buses.
ISE (integrated storage element)

All DSSI storage devices, such as RF disks and TF tapes, are ISEs.
Memory interleaving

Method to optimize memory access time; the VAX 6000 series console
program automatically interleaves the memories in the system unless the
SET MEMORY command is used to set a specific interleave or no interleave

Glossary–3

(which would result in serial access to each memory module). Interleaving
causes a number of memories to operate in parallel.
Memory node

Also called the MS65A. Memory is a global resource equally accessible by
all processors on the XMI. See also MS65A.
Module

A single XMI or VAXBI card that is housed in a single slot in its respective
card cage. XMI modules (11.02" x 9.18") are larger than VAXBI modules
(8.0" x 9.18").
MS65A

XMI memory array; a memory subsystem of the XMI. Memory is a global
resource equally accessible by all processors on the XMI. A memory module
can have 32, 64, or 128 Mbytes of memory, consisting of MOS 1–Mbit or
MOS 4–Mbit dynamic RAMs, ECC logic, and control logic.
Node

An XMI node is a single module that occupies one of the 14 logical and
physical slots on the XMI bus. A VAXBI node consists of one or more
VAXBI modules that form a single functional unit.
Node ID

A hexadecimal number that identifies the node location. On the XMI bus,
the node ID is the same as the physical location. On the VAXBI, the source
of the node ID is an ID plug attached to the backplane.
Pended bus

A bus protocol in which the transfer of command/address and the transfer
of data are separate operations. The XMI bus is a pended bus.
Primary processor

See Boot processor.
Processor node

A VAX processor that contains a central processor unit (CPU), executes
instructions, and manipulates data contained in memory.
RBD

ROM-based diagnostics.

Glossary–4

RBV20/RBV64

VAXBI adapter for write-once-read-many (WORM) optical disk drive. The
RBV20 and RBV64 controllers use the KLESI–B adapter.
Scalar/vector processor pair

The FV64A vector processor functions as a coprocessor with a host scalar
processor. The scalar/vector processor pair appear as one processor to an
executing program.
Secured terminal

Console terminal in program mode while the machine is processing.
Shadow set

Two disks functioning as one disk, each shadowing the information
contained on the other, controlled by an HSC controller under the VMS
operating system.
Symmetric multiprocessing

A multiprocessing system configuration in which all processors have equal
access to operating system code residing in shared memory and can perform
all, or almost all, system tasks.
System root

In a BOOT commmand, the argument to the /R5 qualifier.
TBK70

VAXBI adapter connecting the TK tape drive to the system.
TU81E

VAXBI adapter for a local (nonclustered) tape subsystem.
controller uses the KLESI–B adapter.

The TU81E

VAX Diagnostic Supervisor (VAX/DS)

Software that loads and runs diagnostic and utility programs.
VAXBI bus

The 32-bit bus used for I/O.
VAXBI Corner

The portion of a VAXBI module that connects to the backplane and provides
an electrically identical interface for every VAXBI node.

Glossary–5

VMB

The virtual memory boot program (VMB.EXE) that boots the operating
system. VMB is the primary bootstrap program and is stored on the boot
device. The goal of booting is to read VMB from the boot device and load
the operating system.
XBI

Lines in the self-test display that show the status of DWMBB adapters and
of VAXBI nodes. See also DWMBB.
XMI

The 64-bit, high-speed system bus.
XMI Corner

The portion of an XMI module that connects to the backplane and provides
an electrically identical interface for every XMI node.

Glossary–6

Index
A
Airflow sensor, 2–15, 3–13
Architecture, 1–4

B
Battery backup unit, 2–9, 2–17
location, 1–8, 1–10
status indicator light, 3–11
Baud rate, 5–3, 5–8, 5–57
synchronizing, 5–8
BOOT command, 5–12 to 5–15
default, 4–7
description, 5–15
examples, 5–13
nickname, 4–7
parsing, 4–6
qualifiers, 5–13
storing, 4–7
syntax, 5–15
Boot devices, 4–4, 4–5, D–2
Boot device selection, 4–8 to 4–9
Booting, 4–2 to 4–11
and Star Couplers, 4–13
bootblock, 4–3
boot code, 4–11
boot device, 4–3 to 4–5
local disk, 4–5
TK tape drive, 4–5
VAXcluster disk, 4–5
boot primitives, 4–3
control flags for, F–1 to F–2
Ethernet-based, 4–16 to 4–19
flowchart, 4–2
Model 500 and 600 boot error
messages, J–1 to J–4

Booting (Cont.)
Model 500 and 600 boot status
messages, J–1 to J–4
procedure, 4–3
regular procedure, 4–6 to 4–7
sample commands, 4–7
saved boot specification, 4–7
troubleshooting, 6–18 to 6–19
troubleshooting flowchart, 6–18
ULTRIX, 4–12
VAXcluster, 4–12 to 4–15
VMB, 4–3
Boot processor
designation on self-test results,
6–11
forcing a, 6–20 to 6–21
selection of, 4–10 to 4–11, 6–3
troubleshooting during booting,
6–19

C
CIBCA, D–2
Circuit breaker, 2–8, 3–5, 3–12 to
3–13
CIXCD, 4–3, 4–4, 4–14 to 4–15
Configuration, 1–3
Console, 5–1 to 5–73
baud rate, 5–8
CCA (console communications
area), 5–3
changing terminal characteristics,
5–9
definition of, 5–2 to 5–3
functions, 5–5
load devices, 2–2
mode, 5–6 to 5–7
definition, 5–6

Index–1

Console
mode (Cont.)
entering, 5–6
exiting, 5–7
prompt, 5–3
program, 4–11, 5–3
sample session, 5–72 to 5–73
terminal
baud rate, 5–3, 5–57
defaults, 5–57
description, 5–3
port, 5–3
suspending output, 5–9
Console commands
!, 5–70 to 5–71
abbreviation of, 5–10
BOOT, 5–12 to 5–15
CLEAR EXCEPTION, 5–16 to
5–17
command recall, 5–10
CONTINUE, 5–18 to 5–19
control characters, 5–8 to 5–9
Break key, 5–9
Carriage return, 5–9
CTRL/C, 5–9
CTRL/O, 5–9
CTRL/P, 5–9
CTRL/Q, 5–9
CTRL/R, 5–9
CTRL/S, 5–9
CTRL/U, 5–9
Delete key, 5–9
Escape key, 5–9
DEPOSIT, 5–20 to 5–23
editing, 5–9
EXAMINE, 5–24 to 5–27
FIND, 5–28 to 5–29
functions, 5–4
HALT, 5–30 to 5–31
HELP, 5–32 to 5–33
INITIALIZE, 5–34 to 5–35
list of, 5–1
maximum length, 5–10
numbers, 5–10
qualifier placement, 5–10

Index–2

Console commands (Cont.)
REPEAT, 5–36 to 5–37
RESTORE EEPROM, 5–38 to
5–39
SAVE EEPROM, 5–40 to 5–41
SET BOOT, 5–44 to 5–45
SET commands, 5–42 to 5–55
SET CPU, 5–46 to 5–49
and self-test designation,
6–11
and troubleshooting booting,
6–19
SET LANGUAGE, 5–50 to 5–51
SET MEMORY, 5–52 to 5–54
and self-test results, 6–13
SET TERMINAL, 5–54 to 5–55
SHOW, 5–56 to 5–57
SHOW BOOT
and troubleshooting, 6–19
SHOW CONFIGURATION
and self-test results, 6–17
SHOW FIELD, 5–56 to 5–57
START, 5–58 to 5–59
STOP, 5–60 to 5–61
summary chart, G–1
suspending output, 5–9
syntax, 5–10 to 5–11
TEST, 5–62 to 5–63
UNJAM, 5–64 to 5–65
UPDATE, 5–66 to 5–67
Z, 5–68 to 5–69
Console commands and qualifiers,
G–1 to G–3
Console mode, 3–6
Control panel, 3–2 to 3–3
keys, 3–2
labels, 3–2 to 3–3
location, 1–8
lower key switch, 3–2, 3–6 to 3–7
Restart button, 3–5, 3–8 to 3–9
status indicator lights, 3–10 to
3–11
Battery light, 3–11
Fault light, 3–11
location, 3–10

Control panel
status indicator lights (Cont.)
Run light, 3–11
upper key switch, 3–2, 3–4 to
3–6
Auto Start position, 3–7
Enable position, 3–5
Halt position, 3–7
Off position, 3–5
Secure position, 3–5
Standby position, 3–5
Update position, 3–7
Cooling system, 2–14 to 2–15
airflow pattern, 2–14
airflow sensor, 2–15
blowers, 2–15
location, 1–8, 1–10
space requirements, 2–15
thermostat, 2–15

D
DEBNA, D–2
DEBNI, D–2
DEMFA
booting, 4–23
DEMNA
booting, 4–23
DEPOSIT command, 5–20 to 5–23
Device type codes, C–1
VAXBI, D–1
DHB32, D–2
Disk drives, 2–17
DMB32, D–2
DRB32, D–2
DSB32, D–2
DSSI, 2–7
DWMBB, D–2
self-test, 6–3
self-test results, 6–17
DWMBB/B, D–2
DWMVA adapter, 1–5

E
EEPROM

EEPROM (Cont.)
and self-test, 6–15
patch level, 6–15
restoring, 5–38 to 5–39
saving to tape, 5–40 to 5–41
updating, E–1 to E–2
version number, 6–15
Error messages
changing format, 5–50 to 5–51
console
Model 300, I–1 to I–10
Model 400 and higher, H–1
to H–12
format, 5–7
Ethernet-based compact disk server,
2–4 to 2–5
booting, 4–16 to 4–19
Ethernet booting, 4–16 to 4–27
Ethernet connector, 2–13
EVUCA program, 5–67, E–1 to E–2
EXAMINE command, 5–24 to 5–27

F
FV64A, 5–72

H
Hardcopy output, 5–55
HELP for console commands, 5–32
to 5–33

I
I/O bulkhead connections, 2–12 to
2–13
Ethernet port, 2–13
location, 2–13
panel, 2–13
terminal port, 2–13
tray, 2–13
Initializing the system, 5–35
Input voltages, 2–8
Interleaving
and self-test results, 6–13
SET MEMORY command, 5–52
to 5–54

Index–3

Internationalizing error messages,
5–50 to 5–51

K
KDB50, D–2
KFMSA, 4–3
KLESI–B, D–2

M
Memory, 1–5
self-test, 6–3
self-test results, 6–11, 6–13
Memory size
determining, 6–13

P
Power
troubleshooting during booting,
6–19
Power regulators
location, 1–8, 1–10
Power supply
distribution, 2–8
Power system, 2–8 to 2–9
AC power controller, 2–8
battery backup unit, 2–8
circuit breaker, 3–5
DEC power bus, 3–13
field service port, 3–13
power and logic box, 2–8
switched outlets, 3–13
Primary processor
See Boot processor
Printing terminal output, 5–55
Processor, 1–5
forcing a boot, 6–20 to 6–21
primary, 4–11
secondary, 4–11
self-test, 4–11, 6–3
self-test results, 6–11
Program mode, 3–6
definition, 5–6
entering, 5–7

Index–4

Progress trace, 6–6

R
RBV20/RBV64, D–2
RRD compact disk drive, A–1 to
A–4

S
Secondary processors
See Processor
Self-test
DWMBB, 6–3
EEPROM patch level, 6–15
EEPROM version, 6–15
explanation of sample
configuration, 6–5
line
identification, 6–14 to 6–15
ILV, 6–12 to 6–13
Mb, 6–12 to 6–13
XBI, 6–16 to 6–17
lines
BPD, 6–10 to 6–11
ETF, 6–10 to 6–11
NODE #, 6–8 to 6–9
progress trace, 6–6 to 6–7
STF, 6–8 to 6–9
TYP, 6–8 to 6–9
module self-test status, 6–9
module types, 6–9
node numbers, 6–9
order of testing, 6–2
overview, 6–2 to 6–3
processor and memory
designation on self-test
results, 6–11
progress trace, 6–6 to 6–7
sample, 6–4 to 6–5
system identification, 6–15
VAXBI, 6–3
VAXBI module test results, 6–17
when invoked, 6–4
SET CPU command, 5–46 to 5–49

System
airflow sensor, 2–15
architecture, 1–4
configuration, 1–3
footprint, 1–3
front view, 1–8
initialization, 5–35
rear view, 1–10
serial number, 6–15
thermostat, 2–15
typical, 1–7

T
Tape cartridge, B–1 to B–5
handling and storage, B–5
labeling, B–5
write protecting, B–4
Tape drive, in-cabinet, 2–6 to 2–7,
B–1 to B–5
controls and indicators, B–2 to
B–3
loading a tape, B–3
location, 1–8
unloading a tape, B–4
TBK50, D–2
TBK70, D–2
Temperature, 3–13
Terminal connector, 2–13
TF85 tape drive, B–2
TF tape drive, in-cabinet, 2–6 to
2–7
TK tape drive, in-cabinet, 2–6 to
2–7
TM32, D–2
Troubleshooting, 6–1 to 6–21
during booting, 6–18 to 6–19
forcing a boot processor, 6–20 to
6–21
TU81E, D–2

U
ULTRIX booting, 4–12, F–2

V
VAXBI adapters, D–1 to D–2
self-test, 6–17
VAXBI bus, 1–3 to 1–5
VAXBI card cages, 2–16 to 2–17
location, 1–8, 1–10
VAXBI expander cabinet, D–3
VAXBI modules
self-test, 6–17
VAXBI node
initializing, 5–34
VAXcluster booting, 4–12 to 4–15
Vector processor, 5–73
VMB (virtual memory boot), 4–3
VMEbus, 1–5
VMS booting, F–1
Voltages, input,
VAXBI, D–4
XMI, 2–9

X
XMI adapters, 1–12 to 1–13
XMI bus, 1–3 to 1–5, 2–10 to 2–11
node number of boot processor,
4–11
XMI card cage, 2–10 to 2–11
configuration, 2–11
door, 2–11
interlock switch, 2–11
location, 1–8, 1–10
slot numbers, 2–11
XMI modules
LEDs, 2–11, 6–3
self-test, 6–8
XMI node
ID numbers, 2–11
initializing, 5–34
XMI-to-VAXBI adapter
self-test results, 6–17
XTC module
location, 1–10

Index–5