Digital PDFs

EK-258AA-MG-003

May 1990

328 pages

Original

3.2MB

Document:	VAXstation 3520/3540 Maintenance Guide
Order Number:	EK-258AA-MG
Revision:	003
Pages:	328
Original Filename:	https://manx-docs.org/collections/antonio/dec/MDS-2000-01/cd1/VAX/258AAMG3.PDF

OCR Text

VAXstation
3520/3540 and 3820/3840
Maintenance Guide
Order Number EK-258AA-MG-003

digital equipment corporation
maynard, massachusetts

First Edition, May 1989
Second Edition, September 1989
Third Edition, March 1990
The information in this document is subject to change without notice and should not
be construed as a commitment by Digital Equipment Corporation. Digital Equipment
Corporation assumes no responsibility for any errors that may appear in this document.
The software described in this document is furnished under a license and may be used or
copied only in accordance with the terms of such license.
No responsibility is assumed for the use or reliability of software on equipment that is not
supplied by Digital Equipment Corporation or its affiliated companies.
Restricted Rights: Use, duplication, or disclosure by the U. S. Government is subject to
restrictions as set forth in subparagraph ( c ) ( 1 ) ( ii ) of the Rights in Technical Data and
Computer Software clause at DFARS 252.227–7013.
Copyright © Digital Equipment Corporation 1989, 1990
All Rights Reserved.
Printed in U.S.A.
AT&T is a trademark of American Telephone & Telegraph Company.
The following are trademarks of Digital Equipment Corporation:
DDCMP
MicroVMS
ThinWire
VAXcluster
DEC
PDP
TK
VAXELN
DECconnect
P/OS
TK50
VAXstation
DECmate
Professional
TMSCP
VMS
DECUS
Q-bus
TS
VT
DECwriter
Q22-bus
UNIBUS
VT100
DIBOL
Rainbow
ULTRIX
VT220
KA
RSTS
ULTRIX–32
Work Processor
MASSBUS
RSX
ULTRIX–32m
MicroVAX
RT
VAX

This document was prepared and published by Educational Services Development and
Publishing, Digital Equipment Corporation.

Contents
About This Manual
1

xvii

Hardware

1.1
Workstation Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1.1
External Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2
Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.1
Monitor Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.2
Monitor Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.2.1
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.2.2
Mouse and Tablet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3
System Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.1
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restart/Run Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.1.1
Halt button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.1.2
1.3.1.3
Power Output LED . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.2
Backplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.2.1
M-bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.2.2
Q-bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.2.3
Graphics Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.3
M-Bus Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.3.1
KA60 Dual CPU Module . . . . . . . . . . . . . . . . . . . . . . . .
1.3.3.2
MS60-AA, MS60-BA, and MS60-CA Memory Modules . .
1.3.3.3
I/O Module (L2003) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.3.4
Q-bus and Tape Adapter Modules . . . . . . . . . . . . . . . . .

1–3
1–4
1–6
1–6
1–8
1–8
1–8
1–8
1–10
1–11
1–11
1–11
1–12
1–12
1–13
1–14
1–15
1–15
1–16
1–18
1–19

iii

iv Contents

1.3.4
1.3.4.1
1.3.4.2
1.3.4.3
1.3.4.4
1.3.5
1.3.5.1
1.3.5.2
1.3.5.3
1.3.5.4
1.3.6
1.3.6.1
1.3.6.2
1.3.6.3
1.3.6.4
1.3.7
1.3.7.1
1.3.7.2
1.3.7.3
1.3.7.4
1.3.7.5
1.3.8

Graphics Bus Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graphics Base Module (L2004) . . . . . . . . . . . . . . . . . . .
Graphics Output Module (L2005) . . . . . . . . . . . . . . . . . .
Graphics Expansion Module (L2006) . . . . . . . . . . . . . . .
Graphics Frontplane . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q-Bus Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CXY08 8-Line Asynchronous Multiplexer . . . . . . . . . . . .
DSV11 Communications Option . . . . . . . . . . . . . . . . . . .
TQK70 Tape Drive Controller Module . . . . . . . . . . . . . .
TS05 Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Covers, Connectors, and Indicators . . . . . . . . . . . . . . . . . .
I/O Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graphics Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q-bus Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mass Storage Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mass Storage Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TK70 Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RZ55 Hard Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . .
RZ56 Hard Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . .
TS05 Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RRD40 Optical Compact Disc Drive . . . . . . . . . . . . . . . .
Power Supplies and Fans . . . . . . . . . . . . . . . . . . . . . . . . . .

1–21
1–21
1–21
1–21
1–21
1–23
1–23
1–24
1–25
1–25
1–27
1–28
1–29
1–29
1–29
1–30
1–32
1–33
1–33
1–33
1–33
1–34

Testing and Troubleshooting

2.1
Troubleshooting Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.1
Using Console Mode to Run Tests . . . . . . . . . . . . . . . . . . .
2.1.2
Using an Alternate Console to Run Tests . . . . . . . . . . . . . .
2.1.3
Selecting the Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2
Using Self-Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.1
Displaying Module Location and Error Information . . . . . .
2.2.2
Displaying Information for Individual Modules . . . . . . . . .
2.2.3
Troubleshooting when There Is No Display on the Monitor
2.2.4
Troubleshooting when the Power-Up Self-Test Does Not
Complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.5
Running Self-Tests on Individual Modules . . . . . . . . . . . . .
2.2.6
Setting Loops for Self-Tests . . . . . . . . . . . . . . . . . . . . . . . .

2–1
2–4
2–4
2–5
2–6
2–7
2–9
2–10
2–12
2–16
2–16

Contents v

2.3
Using System Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.1
Running System Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.2
Setting Up Special System Tests . . . . . . . . . . . . . . . . . . . .
2.3.3
Displaying System Test Results . . . . . . . . . . . . . . . . . . . . .
2.4
Troubleshooting the Monitor . . . . . . . . . . . . . . . . . . . . . . . . .
2.5
Troubleshooting Mass Storage Devices . . . . . . . . . . . . . . . . . .
2.5.1
Troubleshooting the TK70 Tape Drive . . . . . . . . . . . . . . . .
2.5.2
Troubleshooting the RZ55 Disk, RZ56 Disk, and the
RRD40 Optical Compact Disc Drives . . . . . . . . . . . . . . . . .
2.6
TEST Command Summary . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7
Interpreting Self-Test Error Messages . . . . . . . . . . . . . . . . . .
2.7.1
I/O Self-Test Error Messages . . . . . . . . . . . . . . . . . . . . . . .
2.7.2
SCSI Self-Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.2.1
Probable Failed FRU . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.2.2
SCSI Self-Test Error Codes . . . . . . . . . . . . . . . . . . . . . .
2.7.2.3
SCSI Extended Information Messages . . . . . . . . . . . . . .
2.7.2.4
Sense Code Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.3
System Support Chip (SSC) Self-Tests . . . . . . . . . . . . . . . .
2.7.3.1
Probable Failed FRUs . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.4
Serial Line Adapter (DZ) Self-Tests . . . . . . . . . . . . . . . . . .
2.7.4.1
Probable Failed FRUs . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.4.2
DZ Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.5
Network Interface (NI) Self-Tests . . . . . . . . . . . . . . . . . . . .
2.7.5.1
Probable Failed FRU . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.5.2
NI Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.6
CPU Self-Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.6.1
Probable Failed FRU . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.6.2
CPU Test Numbers and Error Codes . . . . . . . . . . . . . . .
2.7.7
Memory Self-Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.7.1
Probable Failed FRU . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.8
Graphics Self-Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.8.1
Probable Failed FRU . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.9
Tape Adapter and Tape Drive Controller Self-Tests . . . . . .
2.7.9.1
Probable Failed FRUs . . . . . . . . . . . . . . . . . . . . . . . . . .

2–17
2–17
2–17
2–18
2–19
2–20
2–20
2–21
2–22
2–23
2–23
2–24
2–25
2–25
2–28
2–28
2–30
2–30
2–31
2–32
2–33
2–34
2–34
2–35
2–36
2–36
2–36
2–39
2–39
2–40
2–41
2–41
2–43

vi Contents

2.7.10 DWFQA Q-bus Adapter and Q-bus Option Self-Tests . . . . .
2.7.10.1
CXY08 Self-Test Error Codes . . . . . . . . . . . . . . . . . . . . .
2.7.10.2
DSV11 Self-Test Error Codes . . . . . . . . . . . . . . . . . . . . .
2.7.10.3
TSV05 Self-Test Error Codes . . . . . . . . . . . . . . . . . . . . .
2.8
Interpreting System Test Error Messages . . . . . . . . . . . . . . .
2.8.1
System Test Exception Messages . . . . . . . . . . . . . . . . . . . .
2.8.2
Machine Check Messages . . . . . . . . . . . . . . . . . . . . . . . . . .
2.8.3
Serial Line Adapter (DZ) System Test Error Messages . . .
2.8.3.1
DZ System Test Summary Messages . . . . . . . . . . . . . . .
2.8.4
Memory System Test Error Messages . . . . . . . . . . . . . . . .
2.8.4.1
Memory Extended Information Messages . . . . . . . . . . .
2.8.5
Network Interface (NI) System Test Error Messages . . . . .
2.8.5.1
Extended Information Messages . . . . . . . . . . . . . . . . . .
2.8.6
SCSI System Test Error Messages . . . . . . . . . . . . . . . . . . .
2.8.6.1
SCSI System Test Summary Messages . . . . . . . . . . . . .
2.8.7
LEGSS System Test Error Messages . . . . . . . . . . . . . . . . .
2.8.8
TQK70 System Test Error Messages . . . . . . . . . . . . . . . . .
2.8.9
Q-bus Adapter (DWFQA) System Error Codes . . . . . . . . . .
2.8.10 CXY08 System Test Error Codes . . . . . . . . . . . . . . . . . . . .
2.8.11 DSV11 System Test Error Codes . . . . . . . . . . . . . . . . . . . .
2.8.12 TSV05 System Test Error Codes . . . . . . . . . . . . . . . . . . . .
2.9
Booting the System After Completing Repairs . . . . . . . . . . . .

3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10

2–43
2–44
2–46
2–47
2–48
2–49
2–52
2–56
2–59
2–60
2–60
2–62
2–65
2–66
2–70
2–71
2–72
2–83
2–83
2–86
2–87
2–89

Accessing the Hardware
Using an Antistatic Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turning Off the System Unit . . . . . . . . . . . . . . . . . . . . . . . . .
Removing and Replacing the Front Cover . . . . . . . . . . . . . . .
Removing and Replacing the I/O Cover . . . . . . . . . . . . . . . . .
Removing and Replacing the Graphics Cover . . . . . . . . . . . . .
Removing and Replacing the Graphics Frontplane . . . . . . . .
Removing the SCSI Terminator From the System Unit . . . . .
Removing and Replacing the Mass Storage Cover . . . . . . . . .
Securing the Shipping Brackets for Moving the Workstation .
Removing and Replacing the Back Cover . . . . . . . . . . . . . . . .

3–1
3–2
3–3
3–5
3–7
3–9
3–10
3–12
3–13
3–14

Contents vii

Removing and Replacing FRUs

4.1
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2
Removing and Replacing Internal FRUs . . . . . . . . . . . . . . . .
4.2.1
Inspecting the EOS and FCC Clips . . . . . . . . . . . . . . . . . .
4.2.2
Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.3
System Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.4
Control Panel Module . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.5
Q-bus Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.6
TK70 Series Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.7
TS05 Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.8
RZ55 Hard Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.9
RZ56 Hard Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.9.1
Drive Electronics Module . . . . . . . . . . . . . . . . . . . . . . . .
4.2.10 Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.11 AC Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.12 AC Switch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.13 Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.14 Backplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3
Removing and Replacing External FRUs . . . . . . . . . . . . . . . .
4.3.1
The Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.3
Mouse or Tablet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing Options

5.1
5.2
5.3
5.4
5.4.1
5.4.2
5.4.3
5.5
5.6
5.7
5.8

4–1
4–2
4–2
4–2
4–4
4–7
4–9
4–11
4–13
4–13
4–16
4–18
4–20
4–24
4–25
4–27
4–29
4–32
4–32
4–32
4–33

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
Unpacking and Inspecting an Option Kit . . . . . . . . . . . . . . . . 5–2
Testing the Present Configuration . . . . . . . . . . . . . . . . . . . . . 5–2
Changing the Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
General Module Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
Module Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
Finding CSR Addresses and Interrupt Vectors
with the CONFIG Program . . . . . . . . . . . . . . . . . . . . . . . . 5–4
Testing a New Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 5–5
CXY08 8-Line Asynchronous Multiplexer . . . . . . . . . . . . . . . . 5–6
DSV11 Communications Option . . . . . . . . . . . . . . . . . . . . . . . 5–9
Expansion Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–12

viii Contents

5.8.1
Memory Expansion Module . . . . . . . . . . . . . . . . . . . . . . . .
5.8.2
CPU Expansion Module . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.3
Graphics Expansion Module . . . . . . . . . . . . . . . . . . . . . . . .
5.9
Q-bus Adapter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.10 RRD40 Optical Compact Disc Drive . . . . . . . . . . . . . . . . . . . .
5.11 Tape or Q-bus Adapter Module . . . . . . . . . . . . . . . . . . . . . . .
5.12 TK70 Tape and RZ55/RZ56 Disk Drives . . . . . . . . . . . . . . . . .
5.12.1 Installing Drive Shock Mounts . . . . . . . . . . . . . . . . . . . . . .
5.12.2 Installing Drive Mounting Brackets . . . . . . . . . . . . . . . . . .
5.12.3 TQK70 Tape Drive Controller Module . . . . . . . . . . . . . . . .
5.12.4 TK70 Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.12.5 Internal RZ55 Hard Disk Drive . . . . . . . . . . . . . . . . . . . . .
5.12.6 Internal RZ56 Hard Disk Drive . . . . . . . . . . . . . . . . . . . . .
5.13 TS05 Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5–12
5–12
5–13
5–14
5–15
5–18
5–19
5–19
5–21
5–26
5–28
5–30
5–33
5–36

Equipment Specifications

A.1
A.2
A.3
A.4
A.5
A.6
A.7
A.8
A.9

VS60S System Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–2
VR295 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–3
LK201 Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–4
VSXXX-AA Mouse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–5
VSXXX-AB Tablet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–7
RZ55 SCSI Hard Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . A–9
RZ56 Hard Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–11
TK70 Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–13
RRD40 Optical Compact Disc Drive (Tabletop) . . . . . . . . . . . A–14

Part Numbers

B.1
B.2
B.3
B.4

System FRUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Option Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

B–1
B–4
B–5
B–8

Contents ix

Console Commands

C.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C.1.1
Conventions Used in This Appendix . . . . . . . . . . . . . . . . .
C.1.2
Rules for Entering Console Commands . . . . . . . . . . . . . . .
C.2 Console Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BOOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COMMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTINUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DEPOSIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXAMINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HALT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INITIALIZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
START . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNJAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Z ............................................

Cable and Connector Pin Assignments

Interpreting LED Displays

E.1
E.2
E.3
E.4
E.5
E.6
E.7
E.8
E.9

Graphics Subsystem LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CPU Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tape Adapter Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . .
Tape Drive Controller Module (TQK70) LEDs . . . . . . . . . . . .
Tape Drive (TK70) LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optical Compact Disc Drive (RRD40) LEDs . . . . . . . . . . . . . .
Power Supply LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C–1
C–2
C–2
C–4
C–4
C–5
C–5
C–6
C–8
C–11
C–11
C–12
C–12
C–16
C–18
C–18
C–19
C–19

E–2
E–3
E–3
E–4
E–4
E–5
E–5
E–5
E–6

x Contents

F
F.1
F.2

F.3
F.4

SCSI and SSC Test Numbers and Utilities
SCSI Test Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCSI Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Utility 100: Show SCSI for One I/O Module . . . . . . . . . . .
Utility 102: Spin Drive Up or Down . . . . . . . . . . . . . . . . .
Utility 103: Write/Read/Compare Blocks on Device . . . . .
Utility 104: Format Unit . . . . . . . . . . . . . . . . . . . . . . . . .
Utility 106: Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Utility 107: Perform Seeks on Device . . . . . . . . . . . . . . . .
Utility 108: Read Capacity . . . . . . . . . . . . . . . . . . . . . . . .
Utility 10B: Write/Read/Compare Every Block on Disk
and Reassign Bad Blocks . . . . . . . . . . . . . . . . . . . . . . . . .
Utility 1FF: Set User Write Enable Bit . . . . . . . . . . . . . . .
System Support Chip (SSC) Tests . . . . . . . . . . . . . . . . . . . . .
CPU Test Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

F–1
F–3
F–3
F–5
F–5
F–7
F–8
F–9
F–10
F–11
F–12
F–13
F–19

Index
Examples
2–1
2–2
2–3
2–4
2–5
2–6
2–7
2–8
2–9
2–10
5–1

Sample Power-Up Self-Test Display . . . . . . . . . . . . . . . . . . . .
First-Level Configuration Display . . . . . . . . . . . . . . . . . . . . .
Sample T 50 Mid Configuration Display . . . . . . . . . . . . . . . .
Sample T 50 0 Configuration Display . . . . . . . . . . . . . . . . . .
Sample System Test Error Display . . . . . . . . . . . . . . . . . . . .
Sample I/O Self-Test Display . . . . . . . . . . . . . . . . . . . . . . . . .
Sample DZ System Test Summary Screen . . . . . . . . . . . . . . .
Sample Memory System Test Extended Information Display .
NI Extended Information Display . . . . . . . . . . . . . . . . . . . . .
Sample SCSI Summary Screen . . . . . . . . . . . . . . . . . . . . . . .
Sample Output Using the SYSGEN CONFIG Program . . . . .

2–6
2–7
2–9
2–10
2–18
2–23
2–59
2–61
2–65
2–70
5–5

Contents xi

Figures
1–1
1–2
1–3
1–4
1–5
1–6
1–7
1–8
1–9
1–10
1–11
1–12
1–13
1–14
1–15
1–16
1–17
1–18
1–19
1–20
1–21
1–22
1–23
1–24
1–25
2–1
2–2
3–1
3–2
4–1
4–2
5–1
5–2
5–3

The VAXstation 3520/3540 and 3820/3840 Workstation . . . . .
VAXstation Architecture (Sample Configuration) . . . . . . . . . .
System Unit’s External Connections . . . . . . . . . . . . . . . . . . .
VR295 Monitor Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inside the System Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Panel, Key Switch, and On/Off Switch . . . . . . . . . . .
System Unit Backplane Configuration . . . . . . . . . . . . . . . . . .
Q-bus AB Configuration of the System Unit . . . . . . . . . . . . .
System Unit System Modules . . . . . . . . . . . . . . . . . . . . . . . .
Dual CPU Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q-bus Adapter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tape Adapter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graphics Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CXY08 Module (M3119–YA) . . . . . . . . . . . . . . . . . . . . . . . . . .
DSV11–S Module Layout (M3108–PA) . . . . . . . . . . . . . . . . . .
TQK70 Tape Drive Controller Module and Cable . . . . . . . . . .
TSV05 (M7530) Controller Module . . . . . . . . . . . . . . . . . . . .
Internal Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O Cover, Indicators, and Connectors . . . . . . . . . . . . . . . . . .
Graphics Cover, Frontplane, and Connectors . . . . . . . . . . . . .
System Unit with Internal Mass Storage Devices Installed . .
TSV05 Tape Drive Controller . . . . . . . . . . . . . . . . . . . . . . . . .
System Unit with an RRD40 Optical Compact Disc Drive
Connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting Process (continued) . . . . . . . . . . . . . . . . . . .
Inside the System Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The I/O Cover and Connectors . . . . . . . . . . . . . . . . . . . . . . . .
The System Unit Backplane Configuration . . . . . . . . . . . . . .
Ethernet Address Chip on the I/O Module . . . . . . . . . . . . . . .
CXY08 Module Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSV11–S Module Layout (M3108–PA) . . . . . . . . . . . . . . . . . .
TSV05 (M7530) Controller Module . . . . . . . . . . . . . . . . . . . .

1–2
1–4
1–5
1–7
1–9
1–10
1–12
1–13
1–14
1–16
1–17
1–18
1–19
1–20
1–22
1–23
1–24
1–25
1–26
1–27
1–28
1–29
1–30
1–31
1–32
2–2
2–3
3–4
3–5
4–4
4–5
5–7
5–10
5–37

xii Contents

Tables
1–1
2–1
2–2
2–3
2–4
2–5
2–6
2–7
2–8
2–9
2–10
2–11
2–12
2–13
2–14
2–15
2–16
2–17
2–18
2–19
2–20
2–21
2–22
2–23
2–24
2–25
2–26
2–27
2–28
2–29
2–30
2–31
2–32
2–33

MS60-XX Memory Modules . . . . . . . . . . . . . . . . . . . . . . . . . .
Individual Module IDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting when There Is No Display on the Monitor . .
Troubleshooting when the Power-Up Self-Test Does Not
Complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitor Test Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TEST Command Summary . . . . . . . . . . . . . . . . . . . . . . . . . .
SCSI Error and Severity Messages . . . . . . . . . . . . . . . . . . . .
Sense Code Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Failed FRUs Indicated by DZ Error Codes . . . . . . . . . . . . . . .
DZ Error Codes for Test Number 0 . . . . . . . . . . . . . . . . . . . .
DZ Error Codes for Nonzero Tests . . . . . . . . . . . . . . . . . . . . .
NI Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CPU Self-Test Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CPU Self-Test Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graphics Severity Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graphics Failed-FRU Error Codes . . . . . . . . . . . . . . . . . . . . .
Tape Adapter Module Error Codes . . . . . . . . . . . . . . . . . . . . .
TQK70 Self-Test Error Codes . . . . . . . . . . . . . . . . . . . . . . . . .
DWFQA Q-bus Adapter Self-Test Error Codes . . . . . . . . . . . .
CXY08 Self-Test Error Codes . . . . . . . . . . . . . . . . . . . . . . . . .
DSV11 Self-Test Error Codes . . . . . . . . . . . . . . . . . . . . . . . . .
TSV05 Self-Test Error Codes . . . . . . . . . . . . . . . . . . . . . . . . .
System Test Error Messages . . . . . . . . . . . . . . . . . . . . . . . . .
Machine Check Error Messages . . . . . . . . . . . . . . . . . . . . . . .
DZ Device System Test Error Codes . . . . . . . . . . . . . . . . . . . .
DZ Software Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Errors Reported by Memory System Test Module . .
NI System Test Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NI System Test Error Codes . . . . . . . . . . . . . . . . . . . . . . . . .
NI Kernel Call Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . .
SCSI Device Type Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Status Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCSI Command Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1–16
2–8
2–10
2–12
2–19
2–22
2–25
2–28
2–32
2–33
2–33
2–35
2–36
2–37
2–39
2–40
2–41
2–42
2–42
2–43
2–45
2–46
2–47
2–49
2–52
2–57
2–58
2–60
2–62
2–63
2–64
2–66
2–67
2–67

Contents xiii

2–34
2–35
2–36
2–37
2–38
2–39
2–40
2–41
2–42
2–43
2–44
2–45
2–46
2–47
4–1
4–2
5–1
5–2
5–3
5–4
B–1
B–2
B–3
B–4
C–1
C–2
C–3
C–4
C–5
C–6
D–1
D–2
D–3
D–4
D–5

SCSI System Test Error Codes . . . . . . . . . . . . . . . . . . . . . . . .
SCSI Summary Screen Entries . . . . . . . . . . . . . . . . . . . . . . .
Graphics System Test Error Codes . . . . . . . . . . . . . . . . . . . . .
GVAX Errors 2000 and 2010 . . . . . . . . . . . . . . . . . . . . . . . . .
Host Error 4000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TQK70 System Test Error Codes . . . . . . . . . . . . . . . . . . . . . .
Response Packet Error Codes . . . . . . . . . . . . . . . . . . . . . . . . .
VAXELN Status Error Codes . . . . . . . . . . . . . . . . . . . . . . . . .
SA Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DWFQA Q-bus Adapter System Test Error Codes . . . . . . . . .
CXY08 System Test Error Codes . . . . . . . . . . . . . . . . . . . . . .
DSV11 System Test Error Codes . . . . . . . . . . . . . . . . . . . . . .
TSV05 System Test Error Codes . . . . . . . . . . . . . . . . . . . . . .
Boot Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RZ55 Disk Drive SCSI ID Settings . . . . . . . . . . . . . . . . . . . .
RZ56 Disk Drive SCSI ID Settings . . . . . . . . . . . . . . . . . . . .
Device Abbreviations Used with SYSGEN . . . . . . . . . . . . . . .
RRD40 SCSI ID Switch Settings . . . . . . . . . . . . . . . . . . . . . .
Internal RZ55 Disk Drive SCSI ID Settings . . . . . . . . . . . . .
RZ56 Disk Drive SCSI ID Settings . . . . . . . . . . . . . . . . . . . .
System FRUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Option Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keys with Special Functions in Console Mode . . . . . . . . . . . .
Default Register Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Halt Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Language Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keyboard Type Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MOP Network Listener Control Codes . . . . . . . . . . . . . . . . . .
I/O Cover Ribbon Cable Pin Assignments . . . . . . . . . . . . . . .
I/O Cover SCSI Cable Pin Assignments . . . . . . . . . . . . . . . . .
Keyboard and Mouse/Tablet Connector (I/O Cover)
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communications Connector (I/O) Pin Assignments . . . . . . . .
Printer/Console Connector (I/O) Pin Assignments . . . . . . . . .

2–68
2–70
2–71
2–72
2–72
2–73
2–81
2–81
2–81
2–83
2–84
2–86
2–87
2–89
4–15
4–17
5–5
5–15
5–30
5–34
B–1
B–4
B–5
B–7
C–3
C–11
C–13
C–13
C–14
C–15
D–2
D–3
D–4
D–4
D–6

xiv Contents

D–6 ThickWire Ethernet Connector (I/O) Pin Assignments . . . . . . D–6
D–7 Buses for Slots 1–9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–7
D–8 Buses for Slots 10–12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–7
D–9 Module IDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–7
D–10 M-Bus Backplane Pin Assignments
(Slots 3–9, Connector B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–8
D–11 M-Bus Backplane Pin Assignments
(Slots 4–8, Connector A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–10
D–12 M-Bus MBRQ Connection per Slot . . . . . . . . . . . . . . . . . . . . . D–12
D–13 Q-Bus Slot Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–12
D–14 Q-Bus Backplane Pin Assignments
(Slots 10–12, Connector A) . . . . . . . . . . . . . . . . . . . . . . . . . . D–12
D–15 Q-Bus Backplane Pin Assignments
(Slots 10–12, Connector B) . . . . . . . . . . . . . . . . . . . . . . . . . . D–13
D–16 Q-Bus Backplane Pin Assignments
(Slot 9, Connector A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–14
D–17 Graphics Backplane Pin Assignments
(Slot 3, Connector A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–16
D–18 Graphics Backplane Pin Assignments
(Slots 1–2, Connector A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–18
D–19 Graphics Backplane Pin Assignments
(Slots 1–2, Connector B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–20
D–20 Power Connector Pin Assignments (Connector J25) . . . . . . . . D–21
D–21 Fan Connector Pin Assignments (Connector J26) . . . . . . . . . D–23
D–22 DCOK Connector Pin Assignments (Connector J27) . . . . . . . D–23
D–23 Power Connector Pin Assignments (Connector J29) . . . . . . . . D–23
D–24 Summary of Loopback Connectors . . . . . . . . . . . . . . . . . . . . . D–24
D–25 Printer/Console Loopback Connector Pin Assignments . . . . . D–25
D–26 Modem Loopback Connector Pin Assignments . . . . . . . . . . . . D–25
D–27 Ethernet Loopback Connector Pin Assignments . . . . . . . . . . . D–25
E–1 Graphics Frontplane LED Error Displays . . . . . . . . . . . . . . . E–2
E–2 Memory Module LED Error Displays . . . . . . . . . . . . . . . . . . . E–3
E–3 CPU Module Error Displays . . . . . . . . . . . . . . . . . . . . . . . . . E–3
E–4 Tape Adapter Module LED Displays . . . . . . . . . . . . . . . . . . . E–4
E–5 TK70 Tape Drive LED Displays . . . . . . . . . . . . . . . . . . . . . . . E–5
F–1 Test Format Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . F–13
F–2 Programmable Timer Error Codes . . . . . . . . . . . . . . . . . . . . . F–13
F–3 Timer Transfer Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . F–14

Contents xv

F–4 Timer Run Bit Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . .
F–5 Timer Single-Step Error Codes . . . . . . . . . . . . . . . . . . . . . . .
F–6 Timer Interrupt Error Code . . . . . . . . . . . . . . . . . . . . . . . . . .
F–7 Causes of Timer Interrupt Errors . . . . . . . . . . . . . . . . . . . . .
F–8 Timer Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
F–9 Timer Error Causes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
F–10 Clock Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
F–11 Cause of Clock Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
F–12 CPU Test Numbers and Their Meaning . . . . . . . . . . . . . . . . .

F–14
F–15
F–15
F–16
F–16
F–16
F–17
F–17
F–19

About This Manual
This book is a support and reference manual for Digital Customer
Services personnel who perform maintenance work on the VAXstation
3520/3540 and VAXstation 3820/3840 workstations. It is also for Digital
customers who have a self-maintenance agreement with Digital.
This book assumes that readers are trained technical personnel who have
performed installation and maintenance work on computers such as the
VAXstation 3520/3540 or the VAXstation 3820/3840 workstations. If you
are not a trained technician and your workstation requires maintenance
work, call your Digital service representative.

Organization
This guide contains the following chapters and appendixes:
Chapter 1, ‘‘Hardware,’’ describes the workstation architecture and major
components.
Chapter 2, ‘‘Testing and Troubleshooting,’’ explains using self-tests and
system tests to isolate problem field replaceable units (FRUs).
Chapter 3, ‘‘Accessing the Hardware,’’ contains safety information. The
chapter describes how to shut down the workstation and remove and
replace covers and assemblies.
Chapter 4, ‘‘Removing and Replacing FRUs,’’ describes how to remove and
replace FRUs.
NOTE
Refer to Chapter 3 for information about removing and replacing
any covers or assemblies associated with FRUs.
Chapter 5, ‘‘Installing Options,’’ describes how to install options and
upgrades for the VAXstation 3520/3540 and VAXstation 3820/3840
workstations.
Appendix A, ‘‘Equipment Specifications,’’ lists environmental, regulatory,
electrical, and physical specifications for major components of the
workstation.
xvii

xviii About This Manual

Appendix B, ‘‘Part Numbers,’’ lists part numbers for basic components,
add-on devices, and documentation.
Appendix C, ‘‘Console Commands,’’ describes all console commands,
including command syntax, qualifiers, and special keys.
Appendix D, ‘‘Cable and Connector Pin Assignments,’’ lists the pin
assignments for the cables and connectors used by system unit modules
and options.
Appendix E, ‘‘Interpreting LED Displays,’’ explains the LED displays for
the graphics subsystem, modules, power supply, and options.
Appendix F, ‘‘SCSI and SSC Test Numbers and Utilities,’’ explains the
small computer system interface (SCSI) and system support chip (SSC)
test numbers and utilities.

Conventions
This document uses the following conventions:
Convention

Description

checking
test -a
[var]

Text displayed on the screen appears in monospaced type.
Text you enter from the keyboard appears in bold type.
Italicized text appearing in square brackets indicates optional
arguments you type on a command line.
The word arg indicates you must type an argument on a
command line.
Text in a box identifies a key, such as the Return key.
For sequences that use the Ctrl key, hold down Ctrl and press
the second key.

arg
Return
Ctrl C

Related Documents
See Appendix B for a list of related documentation.

1
Hardware
This chapter introduces the VAXstation 3520/3540 and 3820/3840
architecture. The chapter describes the following major components of
the workstations:
•

Monitor, including keyboard, mouse, and tablet

•

System unit, including system modules, power supplies, and mass
storage devices

NOTE
Make sure you read this chapter before you troubleshoot the
workstation, remove and replace field replaceable units (FRUs),
or install options.
Figure 1–1 shows the workstations.

1–1

1–2 Hardware

DEFM001

Figure 1–1

The VAXstation 3520/3540 and 3820/3840 Workstation

Hardware 1–3

1.1 Workstation Architecture
The VAXstation 3520/3540 and 3820/3840 workstations support three
system buses:
M-bus
Q-bus
Graphics bus

A proprietary bus used only in this workstation.
Modified for use in this workstation.
Used only by the graphics modules.

M-bus modules, such as the central processing unit (CPU), input/output
(I/O), and memory modules, are plugged into the M-bus slots. One
graphics module also plugs into the M-bus. The graphics module
communicates with up to two more graphics modules through a special
graphics bus. The monitor connects to a graphics module and receives
red, green, and blue (RGB) input directly from it.
Q-bus options require an adapter for use with this workstation. Two
adapter modules, the L2002 and the L2008, are currently available to
support certain Q-bus options.
•

L2002—This module plugs into slot 9 of the M-bus and supports the
following Q-bus options:
CXY08
DSV11
TQK70
TSV05

•

L2008—This module also plugs into slot 9 of the M-bus and supports
only the TQK70 option.

Other mass storage devices connect to a small computer systems interface
(SCSI) bus, which is part of the I/O module.
Figure 1–2 illustrates the VAXstation 3520/3540 and 3820/3840
architecture.

1–4 Hardware

Keyboard-Mouse
CPU

Memory

Module

Printer/Console

I/O
Module

Ethernet
SCSI bus (Mass Storage)
Modem

M-bus

Q-bus Adapter
or Tape Adapter
Module

Graphics
Base Module

Q-bus

Graphics bus

To/from Supported

Graphics

To/From

Q-bus Modules

Module

Monitor

MA-X0688-89

Figure 1–2

VAXstation Architecture (Sample Configuration)

1.1.1 External Connections
The workstation system unit has four kinds of external connectors:
•

I/O connectors

•

Graphics connectors

•

SCSI connector

•

Power connector

I/O connectors on the I/O cover connect the system to outside devices,
such as a console, printer, modem, or Ethernet. A portion of the video
cable connects the keyboard and mouse to the I/O cover.
The RGB graphics connectors on the graphics cover carry input signals to
the monitor.

Hardware 1–5

An SCSI connector on the I/O module connects to an SCSI cable that runs
through the mass storage area and terminates at the recessed area on
the upper-left side of the system unit, behind the mass storage cover. An
external device can connect here.
The system unit’s power cord connects to the system unit at the ac filter
assembly on the lower-left side of the system unit.
Figure 1–3 shows the location of the system unit’s external connections.
Optional Optical
Compact
Disc Drive
Cable
Printer/Console
Cable
Keyboard-Mouse
Portion of the
Video Cable

Modem or
Printer/Console
Cable

36-17905-19

RGB Portion of
the Video
Cable
Ethernet Cable
(ThickWire)

DEFI031

Figure 1–3

System Unit’s External Connections

1–6 Hardware

1.2 Monitor
The VR295 monitor connects to the system unit through a video cable
assembly. The assembly carries signals from the I/O cover and RGB input
from the graphics cover.
CAUTION
Placing the monitor near electromagnetic devices (such as
printers or electric pencil sharpeners) or near magnetized objects
(such as filing cabinets or steel beams in walls) can interfere with
the monitor’s performance.

1.2.1 Monitor Controls
The following monitor controls are located on the monitor:
•

Contrast control

•

Brightness control

•

Degauss button

•

On/off switch

•

Power indicator

Figure 1–4 shows the location of the VR295 monitor controls.
The brightness and contrast controls are adjustable dials. The degauss
button restores video display color after it has been affected by magnetic
fields. Ten seconds after you press the degauss button, the circuit is
reactivated. The green power indicator turns on when the on/off switch is
set to the on ( | ) position.

Hardware 1–7

Contrast Control

Brightness Control
Degauss Button
On/Off Switch
in the On
Position

Green
Power Indicator

Figure 1–4

VR295 Monitor Controls

DEFI016

1–8 Hardware

1.2.2 Monitor Connections
The following units connect to the monitor through the video cable:
•

LK201 keyboard

•

VSXXX-AA mouse

•

VSXXX-AB tablet

1.2.2.1 Keyboard
The LK201 keyboard plugs into the video cable assembly connector block
mounted on the back of the monitor. Logic from the I/O module controls
the keyboard. The LK201 keyboard comes in 15 different versions, each
supporting a different language. The keyboard layout depends on the
selected language.
1.2.2.2 Mouse and Tablet
You can use the VSXXX-AA mouse or the VSXXX-AB tablet as a pointing
device. You can only use one pointing device at a time, since both plug
into the same connector on the video cable assembly connector block
mounted on the back of the monitor.
The optional tablet comes with a four-button puck and a stylus. The puck
or the stylus plug into the bottom of the tablet. You can only use one of
these devices at a time.

1.3 System Unit
The system unit includes the following:
•

Control panel

•

Backplane

•

System modules—M-bus, graphics, and Q-bus

•

Covers, connectors, and indicators

•

Mass storage devices

•

Power supplies and fans

To access the mass storage devices, you must remove the mass storage
cover. To access the modules, mass storage cover, and power supplies, you
must remove the front cover of the system unit. To access the backplane,
you must remove the back cover.

Hardware 1–9

Figure 1–5 shows the system unit without the front cover. Disk or tape
drives are behind the mass storage cover. An externally located optical
compact disc drive connects to the SCSI connector. Chapter 3 gives
directions for removing the front cover, back cover, graphics cover, and
mass storage cover. Chapter 4 gives directions for removing modules,
drives, and power supplies.
Mass Storage Cover

Control Panel
Back Cover

SCSI
Connector
Graphics Cover
I/O Cover

Q-bus Covers
R

Power Supply 1

Power Supply 2
RGB Connectors

AC Filter
Assembly
System Unit
power Cord

Figure 1–5

DEFM004

Inside the System Unit

1–10 Hardware

1.3.1 Control Panel
At the front of the system unit, there is a three-position key switch and a
sliding door. Figure 1–6 shows the control panel and switches.
Key Switch Setting

Function

Top dot

The panel locks in the up position.

Middle dot

The panel can slide down partway,
allowing access to the control panel and
the tape drive (if the system has one).

Bottom dot

The panel slides down all the way,
revealing the on/off switch and latch.
Control Panel

Restart/
Run

Halt
Firefox

On/off Switch
in the Off Position

Key

DEFM002

Figure 1–6

Control Panel, Key Switch, and On/Off Switch

Hardware 1–11

When you turn on the system, the orange on/off switch on the system unit
turns on and the system automatically performs a power-up self-test. If
the power-up self-test finds major problems, the system displays a selftest result on the screen. For information about problems that occur at
this stage, see Chapter 2.
1.3.1.1 Restart/Run Button
If you press the Restart/Run button, the system restarts and performs the
power-up self-test.
After the workstation has bootstrapped, the green LED on the Restart/Run
button turns on, indicating that the workstation is running worksystem
software. When the workstation is running diagnostic or console software,
the Restart/Run LED is off.
1.3.1.2 Halt button
If you press the Halt button, the workstation stops running worksystem
software and enters console mode. For information about console mode,
see Chapter 2 and Appendix B.
1.3.1.3 Power Output LED
The LED to the right of the Halt button on the control panel indicates that
the workstation power supply output for both power supplies is within the
proper range for system operation.

1–12 Hardware

1.3.2 Backplane
The backplane has 12 slots and contains up to 12 system modules
(Figure 1–7). The backplane supports three types of buses: the M-bus,
Q-bus, and graphics bus.

Q-bus Covers

I/O Cover

Graphics Expansion
Module (Optional)

Graphics Output Module

Graphics Base Module

I/O Module

Memory Module (Optional)

CPU Module or Memory
Module (OPtional)

CPU Module

Memory Module

Q-bus Adapter Module (Optional)or
Tape Adapter Module (optional)

TQK70 Module (Optional)

Slot
Numbers

Reserved

Slots

Reserved

Module ID (Mid) Numbers

Graphics
Cover
MA-X0689-89

Figure 1–7

System Unit Backplane Configuration

NOTE
To install the TQK70 module in slot 10, the tape adapter module
(L2008) or the Q-bus adapter module (L2002) must be installed in
slot 9.
To install other supported Q-bus options in slots 10 through 12,
the Q-bus adapter module (L2002) must be installed in slot 9.
1.3.2.1 M-bus
The M-bus is a synchronous bus that is accessed through slots 3 through
9. The CPU module resides in slot 7, the I/O module in slot 4, and the
memory module in slot 8. To regulate the power supplies properly, at least
two modules must reside in slots 7 through 12.

Hardware

1–13

1.3.2.2 Q-bus
Backplane slots 10 through 12 provide Q-bus signals on both the top two
and the bottom two connectors. The slots are in an AB AB configuration,
not ABCD (Figure 1–8). The Q-bus slots can accommodate supported
quad (four-connector) or dual (two-connector) Q-bus modules. If a Q-bus
module is installed, a Q-bus adapter module plugs into slot 9.
If a Q-bus module is installed and slots are skipped, the skipped slot
must contain a Q-bus grant module to provide Q-bus continuity. Q-bus
continuity is along the top half of slots 9 through 12, across the bottom of
the backplane, and across slots 12 through 10.
Q-bus

M-bus

First Priority
MA-X0690-89

Figure 1–8

Q-bus AB Configuration of the System Unit

1–14 Hardware

1.3.2.3 Graphics Bus
The graphics bus supports graphics subsystem modules that reside in
slots 1 through 3. The base graphics module resides in slot 3, and the
graphics output module resides in slot 2. Slot 1 contains an optional
graphics expansion module.
A graphics frontplane provides additional communication among the
graphics modules. This connection supports the large amount of
interaction among graphics modules. The graphics frontplane does not
connect the graphics bus and M-bus (Figure 1–9).

Graphics Expansion Module (Slot 1)
Graphics Output Module (Slot 2)
Graphics Base Module (Slot 3)
I/O Module (Slot 4)
CPU Module (Slot 7)
Memory Module (Slot 8)
Tape Adapter Module (Slot 9)

Figure 1–9

System Unit System Modules

DEFM006

Hardware

1–15

1.3.3 M-Bus Modules
M-bus modules include the following:
•

KA60-AA dual CPU module (VAXstation 3520/3540 workstations) or
KA60-BA dual CPU module (VAXstation 3820/3840 workstations)

•

MS60-AA (8 Mbyte), MS60-BA (16 Mbyte), or MS60-CA (32 Mbyte)
memory modules

•

I/O module

•

Tape adapter module (L2008)

•

Q-bus adapter module (L2002)

•

Graphics base module

The M-bus can also accommodate additional optional memory modules
and one additional dual CPU module.
1.3.3.1 KA60 Dual CPU Module
The KA60 dual CPU module is a single M-bus module. Each dual CPU
module contains two functionally independent CPUs, which share a single
set of bus transceivers, clocks, and test-mode connections.
The dual CPU module has its own diagnostic read-only memory (ROM),
with 128 Kbytes for each CPU. The ROM contains console command codes
as well as diagnostic-test firmware.
A VAXstation 3520 or 3820 configuration requires one dual CPU module.
A VAXstation 3540 or 3840 configuration requires two dual CPU modules,
for a total of four processors.
There are eight red LEDs and one green LED on the front edge of the
dual CPU module. The green LED turns on if the module is operating
correctly. If an error occurs, the red LEDs display an error code.
Figure 1–10 shows a dual CPU module.

1–16 Hardware

DEFM059

Figure 1–10

Dual CPU Module

1.3.3.2 MS60-AA, MS60-BA, and MS60-CA Memory Modules
The MS60-AA, MS60-BA, and MS60-CA are single M-bus memory
modules. Table 1–1 compares the three memory modules.
Table 1–1 MS60-XX Memory Modules
Memory Module

Mbytes

Part Number

MS60-AA

L2007-AA

MS60-BA

L2007-AB

MS60-CA

L2007-AC

All three memory modules provide dynamic random-access memory
(RAM), single-bit error correction, and double-bit error detection. Memory
modules respond to M-bus protocol and retain and retrieve data, which is
then used by the system unit’s processors and I/O subsystem. In addition,
memory modules perform self-tests and RAM array initialization.
The system unit can support up to four MS60 memory modules. With four
MS60-BA memory modules, the maximum system unit memory capacity is
64 Mbytes. With four MS60-CA memory modules, the maximum system
unit memory capacity is 128 Mbytes. Slot 8 must contain a memory
module. Additional memory modules can be installed in slots 5, 6, and 9.

Hardware

1–17

NOTE
Memory modules are not backed up by batteries. Any system unit
power loss destroys data stored on them.
The front edge of the memory module includes one red and one yellow
LED.
Yellow LED

Red LED

Indication

Off

The module has passed the self-test.

Off

The module has either failed or the test
is not finished.

The test has not started.

Figure 1–11 shows the memory module.

DEFM060

Figure 1–11

Memory Module

1–18 Hardware

1.3.3.3 I/O Module (L2003)
The system unit must include an I/O module, in slot 4. The I/O module
provides logic shared by the CPUs, including base workstation ROM, RAM
with battery backup, an interval timer, and a time-of-year (TOY) clock.
The I/O module also provides communications logic for the following:
•
•
•
•
•
•

Ethernet
SCSI
Keyboard
Mouse or tablet
Modem
Printer or alternate console

These external devices connect to the I/O module through the I/O cover or
the SCSI connector. The I/O module has two connectors:
•

I/O connector—Connects the I/O module to the I/O cover.

•

SCSI connector—Connects the I/O module to the internal SCSI cable.

The green LED on the I/O module turns on when the module operates
correctly.
Figure 1–12 shows the I/O module.

DEFM061

Figure 1–12

I/O Module

Hardware

1–19

1.3.3.4 Q-bus and Tape Adapter Modules
The L2002 Q-bus adapter module (Figure 1–13) connects Q-bus modules
to the M-bus. The Q-bus adapter module installs in slot 9 and supports
the Q-bus modules installed in slots 10 through 12. The following Q-bus
options are currently supported:
CXY08
TQK70
DSV11
TSV05

Green LED

Red LEDs

MA-X0693-89

Figure 1–13

Q-bus Adapter Module

1–20 Hardware

The front edge of the adapter module has one green LED and a set of red
LEDs. The green LED turns on if the adapter is operating properly. The
red LEDs display an error code if the adapter module fails the self-test.
The L2008 tape adapter module supports only the TQK70 tape drive
controller module. The tape adapter module installs in slot 9 and supports
a tape drive controller module installed in slot 10.
The front edge of the adapter module has one green LED and a set of
red LEDs. The green LED turns on if the adapter is operating properly.
The red LEDs display an error code if the adapter module fails self-test
(Figure 1–14).

Green LED

Red LEDs

DEFM073

Figure 1–14

Tape Adapter Module

Hardware

1–21

1.3.4 Graphics Bus Modules
The workstation graphics subsystem receives graphics commands and
data from the CPU module and generates video images independently.
The subsystem contains either two or three modules:
•

Graphics base module

•

Graphics output module

•

Graphics expansion module (optional)

Modules in the graphics subsystem reside in slots 1 through 3 and
communicate with each other through a special graphics bus.
1.3.4.1 Graphics Base Module (L2004)
The graphics base module serves as the graphics coprocesser for the
workstation and links the M-bus and graphics bus. The module provides
timing, addressing, and control functions for the graphics subsystem.
Every workstation must have a graphics base module installed in slot 3.
1.3.4.2 Graphics Output Module (L2005)
The graphics output module provides video output circuitry for the
workstation. This module also has eight planes of graphics memory,
which provides bitmap color output to the monitor. Every system unit
must have one graphics output module installed in slot 2.
1.3.4.3 Graphics Expansion Module (L2006)
The optional graphics expansion module provides an additional 16 planes
of graphics memory, extending the graphics subsystem to 24 planes.
When a graphics expansion module is installed in a workstation, the
graphics output module (slot 2) provides true color output (16.7 million
possible colors) to the monitor. If you use the graphics expansion module,
it must be installed in slot 1.
1.3.4.4 Graphics Frontplane
The graphics frontplane carries additional signals between the graphics
modules in slots 1 through 3.
Figure 1–15 shows the graphics subsystem.

1–22 Hardware

Graphics Base Module

Graphics Output Module

1/4-Turn Captive
Fasteners
Graphics Cover

LED Status
Displays

B
G

BNC Connector
Icon

RGB Connectors
Graphics
Frontplane

DEFM009

Figure 1–15

Graphics Subsystem

Hardware

1–23

1.3.5 Q-Bus Modules
The following Q-bus modules are currently supported:
CXY08
DSV11
TQK70
TSV05
1.3.5.1 CXY08 8-Line Asynchronous Multiplexer
The CXY08 asynchronous multiplexer performs data concentration, realtime processing, and interactive terminal handling. The CXY08 is a quadheight module with a BA200 series handle (Figure 1–16). The CXY08
option also includes two cable assemblies. The module provides eight
full-duplex serial data channels. Each cable assembly has a four-channel
distributor.
All eight channels allow autoanswer dial-up operation over the publicswitched telephone network. You can use AT&T 103, 113, and 212
modems, or the equivalent.

DSV11
-SA
M3108
-PA

MA-X0009-88

Figure 1–16

CXY08 Module (M3119–YA)

1–24 Hardware

1.3.5.2 DSV11 Communications Option
The DSV11 (Figure 1–17) is a two-channel, high-speed, synchronous
communications option for use on Q-bus backplanes.
The DSV11 supports the following synchronous communications protocols:
DDCMP
HDLC/SDLC
BISYNC
The DSV11 allows any of the following synchronous interfaces:
RS–423
RS–422
RS–232/V.24
V.35

LEDs

E32
E89

MA-X0014-88A

Figure 1–17

DSV11–S Module Layout (M3108–PA)

Hardware

1–25

1.3.5.3 TQK70 Tape Drive Controller Module
The TQK70 tape drive controller module is an interface between the CPU
and the TK70 tape drive. The TQK70 can be supported by either the
L2008 tape adapter module or the L2002 Q-bus adapter module, installed
in slot 9. If you use the L2008 tape adapter module, install the TQK70 in
slot 10. If you use the L2002 Q-bus adapter module, install the TQK70 in
slot 10, 11, or 12.
A cable attached to the tape controller module connects the module to the
TK70 tape drive (Figure 1–18).

From TK70 Tape Drive

DEFM007

Figure 1–18

TQK70 Tape Drive Controller Module and Cable

1.3.5.4 TS05 Tape Drive
The TS05 is a magnetic streaming tape drive that provides 40.5 Mbytes of
backup data storage.
The TS05 reads or writes up to 160 Kbytes per second (Kbytes/s) in
standard ANSI format. The drive uses automatic read after write to
verify that data is accurately recorded.
Tape data is buffered in 3.5 Kbytes of RAM on the drive’s TSV05
controller (M7530). The TSV05 is a tape mass storage control protocol
(TMSCP) device (Figure 1–19).

1–26 Hardware

Front Panel

EMULEX

U15
J4
Novram

U43
Firmware
Prom

K
J
H
G
F
E
D

LED

SW2

Host
Adapter

2
1

SW1

Controller
(HAC)

OFF/ON
J2

U39
8031

C
U50

Buffer
Controller

MA-X0697-89

Figure 1–19

TSV05 (M7530) Controller Module

Hardware

1–27

1.3.6 Covers, Connectors, and Indicators
The system unit has four types of internal covers (Figure 1–20):
•

I/O cover

•

Graphics cover

•

Q-bus cover

•

Mass storage cover

Each cover has various connectors and indicators.
Mass Storage Cover

Graphics Cover
I/O Cover

Q-bus Covers
R

DEFM022

Figure 1–20

Internal Covers

1–28 Hardware

1.3.6.1 I/O Cover
The I/O cover fits over the modules in slots 4 through 9. It contains
external I/O cover connectors, a hexadecimal display, and a rechargeable
battery. You remove the I/O cover (but not necessarily the I/O cable) to
expose modules in slots 4 through 9. To remove the battery, you must
remove the I/O cover.
The I/O cover contains the following (Figure 1–21):
•

Hexadecimal system status display

•

Serial modem connector (25 pins)

•

ThickWire Ethernet connector (15 pins)

•

ThinWire Ethernet connector

•

Serial printer/console connector

•

Serial keyboard-mouse connector (15 pins)

•

Ethernet switch for selecting ThinWire or ThickWire Ethernet

Status Display

Modem Connector

ThickWire
Ethernet
Connector

Printer Connector

Keyboard/Mouse
Connector

Ethernet Switch

ThinWire
Ethernet
Connector

Figure 1–21

I/O Cover, Indicators, and Connectors

DEFM008

Hardware

1–29

1.3.6.2 Graphics Cover
The graphics cover (Figure 1–22) fits over the graphics frontplane and the
two or three graphics modules installed in slots 1, 2, and 3. You can see
the LED displays and the RGB connectors on the frontplane.
1/4-Turn Captive
Fasteners

Graphics
Cover

Icon Label
R

B
G

RGB Connectors

Graphics
Frontplane

DEFM076

Figure 1–22

Graphics Cover, Frontplane, and Connectors

1.3.6.3 Q-bus Covers
Q-bus covers fit over the individual Q-bus slots.
1.3.6.4 Mass Storage Cover
The mass storage cover fits over the mass storage area, the control panel,
and the mounting recess for the SCSI connector.

1–30 Hardware

1.3.7 Mass Storage Devices
Five types of mass storage devices are available:
•

Internal TK70 tape drive

•

Internal RZ55 hard disk drive

•

Internal RZ56 hard disk drive

•

External TS05 tape drive

•

External RRD40 optical compact disc drive

The internal devices are in the mass storage area at the top of the
system unit, behind the mass storage cover. The mass storage area can
accommodate a maximum of four standard 13.3 cm (5.25 in.) hard disk
drives or three hard disk drives and one TK70 tape drive.
RZ55/RZ56 Disk Drives

TK70 Tape Drive
DEFM010

Figure 1–23

System Unit with Internal Mass Storage Devices Installed

Hardware

1–31

The external, industry-standard TS05 tape drive connects to the TSV05
controller through the TSV05 handle (Figure 1–24).
Front Panel

EMULEX

U15
J4
Novram

U43
Firmware
Prom

K
J
H
G
F
E
D

LED

SW2

Host
Adapter

2
1

SW1

Controller
(HAC)

OFF/ON
J2

U39
8031

C
U50

Buffer
Controller

MA-X0697-89

Figure 1–24

TSV05 Tape Drive Controller

The external optical compact disc drive attaches to the system unit at the
SCSI connector. Figure 1–25 show the system unit with an RRD40 optical
compact disc drive connected.
CAUTION
Using a cable other than the Digital-supplied seven-foot SCSI
cable can cause the device to malfunction.

1–32 Hardware

RRD40 Drive
R

DEFI062

Figure 1–25
Connected

System Unit with an RRD40 Optical Compact Disc Drive

1.3.7.1 TK70 Tape Drive
The TK70 tape drive can store up to 296 Mbytes of data on a single
cartridge. The tape drive faces the front of the system unit and installs
at the far right of the mass storage area, in the tape drive slot. The
drive mounts on slide supports in the mass storage area to protect it from
mechanical shock. Chapter 5 describes how to install the TK70 option.

Hardware

1–33

1.3.7.2 RZ55 Hard Disk Drive
The RZ55 hard disk drive is preformatted at the factory to provide
a storage capacity of 332 Mbytes. Hard disk drives face the rear of
the system unit to provide easy access to the drive signal and power
cables. The drives install from right to left in the mass storage area. The
drives mount on slide supports to protect them from mechanical shock.
Chapter 5 describes how to install the RZ55 option.
NOTE
If the system unit does not have a tape drive, the first RZ55 must
be installed in the tape drive slot at the far right of the mass
storage area , facing the front of the system unit.
1.3.7.3 RZ56 Hard Disk Drive
The RZ56 hard disk drive is preformatted at the factory to provide
a storage capacity of 665 Mbytes. Hard disk drives face the rear of
the system unit to provide easy access to the drive signal and power
cables. The drives install from right to left in the mass storage area. The
drives mount on slide supports to protect them from mechanical shock.
Chapter 5 describes how to install the RZ56 option.
NOTE
If the system unit does not have a tape drive, the first RZ56 must
be installed in the tape drive slot at the far right of the mass
storage area , facing the front of the system unit.
1.3.7.4 TS05 Tape Drive
The TS05 is a magnetic streaming tape drive that provides 40.5 Mbytes
of backup data storage. The TS05 reads or writes up to 160 Kbytes/s in
standart ANSI format. The drive uses automatic read after write to verify
that the data is accurately recorded.
The TS05 is outside the system and connects to the system through the
handle on the TSV05 controller (installed in slot 10, 11, or 12). Chapter 5
describes how to install the TS05 option.
1.3.7.5 RRD40 Optical Compact Disc Drive
The RRD40 optical compact read-only disc drive is preformatted to provide
a storage capacity of 635 Mbytes. The RRD40 is outside the workstation
and attaches to the system unit by means of a SCSI cable.

1–34 Hardware

1.3.8 Power Supplies and Fans
The system unit comes with two H7868 power supplies that provide
regulated voltage to the backplane, drives, and fans. Each power supply
plugs directly into the backplane by means of a 56-pin connector and
provides 230 watts of power with the following maximum current:
•

7.0 amps at +12 Vdc

•

33.0 amps at +5 Vdc

An ac line filter under the left power supply area distributes ac input
power to the two power supplies. Each power supply has a six-pin ac
input power connector at its base.
On the front of each power supply is a power indicator, a reset button
button, and a circuit breaker. The on/off switch above the right power
supply acts as an ac power indicator; the switch lights up when the
workstation is turned on and ac voltage is present in the power supply.
The green DCOK LED to the right of the Halt button on the control panel
turns on when dc power from both power supplies is within the required
range.
An LED on the front of each power supply turns on when the dc output
from the power supply is within the required range. If the DCOK LED
indicator on the control panel is off, the dc power-supply LED indicates
which supply has failed.
System modules receive power through the backplane. A cable connects
mass storage devices to the power supply. The cable connects to the
power supply with a nine-pin connector and to each drive with a four-pin
connector.
The right power supply (power supply 1) provides power to the six
backplane slots and the two mass storage devices on the right side of
the workstation. The left power supply (power supply 2) provides power
to the six backplane slots and any mass storage devices on the left side of
the workstation.
Fans are under the card cage slots. The right power supply provides
power to both fans.

2
Testing and Troubleshooting
This chapter explains troubleshooting the VAXstation 3520/3540 and
3820/3840 workstations. This troubleshooting material discusses
•

How to run and interpret self-tests

•

How to run and interpret system tests

2.1 Troubleshooting Process
Figures 2–1 and 2–2 show the workstation troubleshooting process used
to identify faulty field replaceable units (FRUs).
This troubleshooting process assumes that problems are not caused by
such things as faulty power cords or loose modules and connectors.
Workstation troubleshooting involves two types of tests:
•

Self-tests, which check modules as separate units

•

System tests, which check modules both as separate units and
together as a system

The self-test alone usually identifies faulty FRUs. The system test,
however, is useful for finding intermittent failures and problems in
module interaction. Always run both types of tests when troubleshooting
the workstation.
These tests also check the operation of the monitor and mass storage
devices.

2–1

2–2 Testing and Troubleshooting

Start

Is There
a Display on the

Monitor ?

Yes
Refer to Table 2-2
to Troubleshoot .
Does
System Complete

the Power-up
Self-Test ?
Refer to Table 2-3
to Troubleshoot .
Yes

Does the
Self-Test Log Error
Codes ?

Run System Tests .

Yes
A
MA-X0691-89

Figure 2–1

Troubleshooting Process

Testing and Troubleshooting 2–3

B
Yes
Interpret Self-Test Error
Codes to Determine
Problem Module .
Replace Failed FRU .

Run System Tests .

Does
System Test Log
Errors ?

Yes

Interpret System Test
Error Codes to
Determine Problem Module .
Replace Failed FRUs .

Reboot System to
Verify That Operating
System is Loaded .

Does
Worksystem
Load ?

Contact Digital
Support Service .

Yes
Test Complete
Test Complete

MA-X0696-89

Figure 2–2

Troubleshooting Process (continued)

2–4 Testing and Troubleshooting

2.1.1 Using Console Mode to Run Tests
The workstation operates in two modes:
•

Console mode, used for test and boot functions

•

Operating mode, used for regular workstation software operation

You must be in console mode to run tests.
The workstation automatically starts in console mode when the system
powers up. When the system is in console mode, the monitor displays
the prompt CPUxx >>> where xx represents the ID number of the CPU
handling the console commands.
If you are in operating mode and wish to return to console mode,
press either the Restart/Run or the Halt button.
•

Pressing the Restart/Run button causes the system to enter console
mode and complete a self-test before returning the console prompt.

•

Pressing and holding the halt button stops system activity. When
you release the Halt button, the system enters console mode without
performing a self-test.

To exit console mode, enter operating mode by typing one of the
following commands:
•

BOOT

•

START

•

CONTINUE

Refer to Appendix C for an explanation of console commands.

2.1.2 Using an Alternate Console to Run Tests
You may use an alternate console to run tests. Use a VT100 or VT220
terminal set to 9600 baud, 8 bits and no parity.
To connect an alternate console:
1. Turn off the workstation.
2. Connect a DEConnect cable to the printer/console connector on the I/O
cover.
3. Connect the other end of the cable to the alternate console.
4. Turn on the alternate console.
5. Turn on the workstation.

Testing and Troubleshooting 2–5

6. Press and hold the Halt button on the control panel until the power-up
display appears on the alternate console screen (approximately 10
seconds). Then release the button.
If an alternate console is already connected to the workstation,
press and hold the Halt button until the DCOK LED on the control panel
begins to blink (approximately 10 seconds). The LED display blinks faster
when the system transfers control to the alternate console.
The system monitor displays video test patterns if you enter the
commands at the alternate console. The system monitor keyboard does
not work while an alternate console is in use.
To return to using the original console, press the Restart/Run button
or turn the system power off and then on again.

2.1.3 Selecting the Test Mode
Workstation tests run in either customer mode or field service mode,
depending on whether loopback connectors and terminators are present
on the I/O cover.
•

Customer mode, the system’s default setting, requires no loopback
connectors. The test mode is set to customer mode each time the
system powers up.

•

Field service mode requires loopback connectors.
NOTE
Appendix B lists part numbers for all the required connectors.

To set the system to field service mode, first install the following
connectors on the I/O cover:
•

Printer/console loopback on the printer/console connector

•

Either a T-connector with two terminators on the ThinWire Ethernet
connector, or a ThickWire loopback connector on the ThickWire
Ethernet connector

•

H3200 loopback on the modem connector

Set the Ethernet switch to the correct position for the type of Ethernet
connector on the system.
After the loopback connectors are in place, type T 200 and press Return . If
loopback connectors are present, the system enters field service mode. If
loopback connectors are not present, the system stays in customer mode.

2–6 Testing and Troubleshooting

To return to customer mode, do one of the following:
•

Remove the loopback connectors, type T 200 and press Return , or

•

Press the

button.

Restart/Run

2.2 Using Self-Tests
The VAXstation system is designed to perform a comprehensive self-test
when the system powers up or you press the Restart/Run button. The
monitor and LEDs on each module report power-up self-test results.
When the self-test sequence finishes, the monitor displays an error
message for each failure it detects.
Example 2–1 shows a sample display for a power-up self-test that detected
faults in the I/O and graphics modules.
KA60 V1.1
F..E..D..C..B..A..9..8..7..6..5..4..3..2..1..0
4 01010004
1
2
3
4
5

SSC
DZ
NI
SCSI
SYS

00000001
00000001
19210770
00000901
00000001
7

GFX

L2003

V1.1

01010002

L2004

20163B12
??
00000200

00000006

V1.1-B

Tests completed.
OC-E1, P1
OF-E1, P1
OC
CPUxx >>>

Example 2–1

Sample Power-Up Self-Test Display

The first line shows the CPU name (KA60) and ROM version.
Hexadecimal numbers in the second line represent different parts
of the power-up self-test. The hexadecimal numbers F..E..D..C..
appear on the screen all at once. The other test numbers appear as
the corresponding test starts. The I/O cover LED simultaneously displays
the same numbers.

Testing and Troubleshooting 2–7

Error messages after the first two lines identify failed modules and
include a code describing the particular failure. I/O, graphics, and tape
adapter module error messages provide separate error messages for
modules and devices in their subsystems.
Each module’s error codes are explained later in this chapter.

2.2.1 Displaying Module Location and Error Information
Use the configuration display to find each module’s physical location and
quickly identify faulty modules.
The self-test reports error information by M-bus ID (mid) number, which
depends on a module’s location in the card cage. To find a module’s mid
number, type T 50 and press Return .
A configuration display like the one in Example 2–2 appears.
KA60 V1.0
MID
MODTYPE
0
01010001
1
00020010
2
00000000
3
01010108
4
01010004
5
00000000
7
01010002

ID
SLOT
L2002
9
L2007AA
8
*
7
L2001
6
L2003
5
*
4
L2004
3

ERR

?
??

CPU08 >>>

Example 2–2

First-Level Configuration Display

•

MID is the module’s M-bus ID. The mid numbers begin at slot 9 and
end at slot 3. There is no mid number 6.

•

MODTYPE is the module-type number. Eight 0s appear in the
MODTYPE listing if that slot is empty.

•

ID represents the module’s logical name. These numbers also appear
on the module’s front edge.
— Asterisks appear in the ID listing if that slot is empty.
— If an asterisk is in the ID column but 0s do not appear in the
MODTYPE column, the module has a defective ROM chip.
Replace any module that has a defective ROM chip.

2–8 Testing and Troubleshooting

Table 2–1 lists ID numbers and the modules they represent.
Table 2–1 Individual Module IDs
ID

Module Name

L2001

KA60-AA CPU module

L2002

Q-bus adapter module

L2003

I/O module

L2004

Graphics base module

L2005

Graphics output module

L2006

Graphics expansion module

L2007-AA

MS60-AA, 8-Mbyte memory module

L2007-BA

MS60-BA, 16-Mbyte memory module

L2007-CA

MS60-BA, 32-Mbyte memory module

L2008

Tape adapter module

L2010

KA60-BA CPU module

•

SLOT indicates a module’s physical slot in the card cage. Note the
following:
— Modules in slots 1 and 2 are subsets of the graphics base module
in slot 3. If any graphics module generates an error, the graphics
module in slot 3 reports the failure.
— Slots 10 through 12 are Q-bus slots. If a Q-bus module fails the
self-test, the error display reports a failure in the Q-bus adapter
module (L2002) or the tape adapter module (L2008) in slot 9.

•

ERR shows question marks if the corresponding module generated an
error during the power-up self-test.
— One question mark (?) indicates a nonfatal error.
— Two question marks (??) indicate a fatal error.

Testing and Troubleshooting 2–9

2.2.2 Displaying Information for Individual Modules
To display configuration and test results for specific modules and devices,
type T 50 mid where mid is the module ID number, and press Return .
The monitor displays that module’s configuration and any current error
information.
For example, in Example 2–2 you can see that the M-bus ID for the I/O
module (L2003) is 4. To display the I/O subsystem configuration, type T
50 4 and press Return . The display will be similar to that in Example 2–3.
4
1
2
3
4
5

01001004
SSC
DZ
NI
SCSI
SYS

L2003

00000001
00000001
BF070404
00000001
00000001

Example 2–3

V1.1

Sample T 50 Mid Configuration Display

The top line lists the module’s ID, type, name, and slot number. The ROM
version number appears at the far right of this line.
The rows below these headings list the number, name, and current error
information for each I/O device.
This sample display reports an error in the network interface (NI). The
error code 00000001 in the other messages means the self-test detected no
errors.
NOTE
If the self-test reports a nonfatal error in the network interface
(NI), install a loopback connector on the Ethernet connector on
the I/O cover and set the Ethernet switch to the correct setting.
Then repeat the self-test. If the nonfatal error persists, the I/O
module is faulty.

2–10 Testing and Troubleshooting

To display the configuration for the DWFQA Q-bus adapter module,
type T 50 0 and press Return . The display will be similar to that in
Example 2–4.
NOTE
Note the CSR and vector settings for each Q-bus device. If a Qbus device is installed in the system but does not appear in the
configuration display, verify that the CSR and vector settings are
correct.
0
1
2

0101001
QAM
TQK70

L2002

00000001
00000001

V1.1

X2.0
X2.0

CSR = 00001940
VEC = 000000B0

Example 2–4

Sample T 50 0 Configuration Display

2.2.3 Troubleshooting when There Is No Display on the
Monitor
If there is no display on the monitor, you can use the system’s LEDS and
indicators to troubleshoot. Refer to Table 2–2.
Table 2–2 Troubleshooting when There Is No Display on the Monitor
Problem

Remedy

The monitor’s power
indicator does turn
on.

Make sure the monitor is turned on. Check the
monitor’s power supply and outlet. Refer to the
monitor’s maintenance guide if the power indicator
still does not turn on.

The workstation’s
power indicator does
not turn on.

Make sure the workstation’s power supply is turned on.
Check the workstation’s power cord and outlet. If the
power indicator still does not turn on, troubleshoot the
workstation’s power supply.

Testing and Troubleshooting 2–11

Table 2–2 (Cont.) Troubleshooting when There Is No Display on the
Monitor
Problem

Remedy

The green DCOK LED turns on if both power supplies
are operating correctly. If the DCOK LED does not turn
on, first check the power supplies. A green LED at the
top of each power supply turns on if that power supply is
operating correctly. Reset any open power supply circuit
breakers.
If both power supplies do not operate, replace the ac
power filter. If one power supply does not operate,
replace the defective power supply.
The RGB video
cable is not correctly
connected to the
monitor and system
unit.

Connect the RGB cable correctly. Make sure the RGB
connectors are attached in the proper order.

The system does
not complete the
power-up self-test.

Refer to Table 2–3 to troubleshoot the workstation.

The LEDs on the
graphics frontplane
do not count down to
zero.

Check the red LEDs on the graphics frontplane. These
LEDs display an error code if the graphics subsystem
fails the self-test. Sometimes the tests cannot isolate the
single failed module. In that case, the LEDs identify two
or three probable failed modules. Refer to Appendix F
for an explanation of graphics LED error codes.

There is still no
display on the
monitor.

Remove and replace the video cable.

There is no display
on the monitor after
the video cable is
replaced.

Refer to the monitor’s maintenance guide to troubleshoot
the monitor.

2–12 Testing and Troubleshooting

2.2.4 Troubleshooting when the Power-Up Self-Test Does
Not Complete
If the power-up self-test does not complete, you can use module LEDs to
isolate faulty FRUs. Refer to Table 2–3.
Table 2–3 Troubleshooting when the Power-Up Self-Test Does Not
Complete
Stop Location

Remedy

Beginning. Test does
not start.

Check for loose and damaged connectors. Reseat any
loose modules. If the system still does not start, there is
a basic problem in the system. Contact Digital support
service.

The problem is in the CPU module, I/O module, or I/O
cover. Each CPU module has one green LED and two
sets of red LEDs. The green LED turns on if the CPU is
operating correctly. If the green LED does not turn on,
one or both of the red LED sets displays an error code.
•

If the red LEDs do not display 9 (10012 ), the
problem is in the CPU module itself. Replace the
CPU module and retry the power-up self-test.

•

If the red LEDs do display 9, the problem may be in
the CPU module, the I/O module, or the I/O cover.
Troubleshoot these three modules to correct the
problem. Contact Digital support service if the test
still stops at F.

The green LED may be on even if the module has failed.
If troubleshooting other modules does not correct the
problem, replace the CPU module. If the self-test still
stops at F, contact Digital support service.
E

The problem is in the I/O module. The green LED on the
I/O module turns on if the module is operating correctly.
Replace the I/O module if the green LED does not turn
on. If the I/O module LED is on and the self-test still
stops at E, replace the I/O cover. Contact Digital support
service if the problem continues.

The problem is in the CPU module. If the CPU module
fails, the green LED does not turn on, and the red LEDs
display an error code. Replace the CPU module. Contact
Digital support service if the problem continues.

Testing and Troubleshooting 2–13

Table 2–3 (Cont.) Troubleshooting when the Power-Up Self-Test Does
Not Complete
Stop Location

Remedy

The problem is in the I/O or graphics subsystem. Check
the red LEDs on the graphics frontplane and the green
LED on the graphics base module.
•

If the green LED is off and the red LEDs are on,
there is a problem in the graphics subsystem.
Follow Procedure 1 to troubleshoot the graphics
modules.

•

If the red LEDs on the graphics frontplane are
all off, the graphics module is operating correctly.
Follow Procedure 2 to troubleshoot the I/O module.

Procedure 1: The red LEDs display an error code
that identifies a problem module in the graphics
subsystem. Appendix F explains specific LED error
codes. Sometimes the tests cannot isolate the failed
FRU. In that case, the LEDs identify the two or three
most probable failed modules.
If replacing modules does not correct the problem,
replace the graphics frontplane. Contact Digital support
service if the problem continues.
Procedure 2: The green LED on the I/O module is on if
the I/O module is operating correctly. If the green LED
does not turn on, replace the I/O module. If the green
LED is on, replace the I/O cover. Contact Digital support
service if the problem continues.

2–14 Testing and Troubleshooting

Table 2–3 (Cont.) Troubleshooting when the Power-Up Self-Test Does
Not Complete
Stop Location

Remedy

The problem is in the memory module. Check the
memory module LEDs.
Each memory module has one red and one yellow LED.
Yellow

Red

Indication

Off

The module passed the selftest.

Off

The module has failed, or the
test is still running.

The test has not started.

Off

There is no power to the
module, or the LEDs are not
working.

The memory self-test can take several minutes to
complete. Allow time for this test to complete before
assuming the test has stopped. Replace any modules
that have their red LED on and yellow LED off. Contact
Digital support service if the problem continues.
9

If the DWFQA Q-bus adapter (L2002) module is
installed in slot 9, the problem is in the Q-bus adapter
module.
Check the Q-bus adapter module LEDs. The green LED
turns on if the module is operating correctly. If there
are Q-bus options installed, there may be a problem
with one or more of the Q-bus options. Isolate the faulty
module or modules by removing one module at a time.
If you isolate a faulty module or modules, verify that
the CSR and vector settings are correct. Contact Digital
support service if the problem continues.

Testing and Troubleshooting 2–15

Table 2–3 (Cont.) Troubleshooting when the Power-Up Self-Test Does
Not Complete
Stop Location

Remedy

If the tape adapter module (L2008) is installed, the
problem is in the tape adapter module in slot 9 or the
TQK70 tape drive controller module in slot 10. The selftest stops if the Q-bus contains any module other than a
TQK70.
Check the tape adapter module LEDs. The green
LED turns on if the tape adapter module is operating
correctly.
If the tape adapter module is operating correctly, check
the tape controller module. The top and bottom LEDs
are both off if the tape drive controller module is
operating correctly. If the tape drive controller module
LEDs are flashing, the problem is probably in the CPU
or interface between the tape controller and tape adapter
modules.
If the tape adapter module is operating correctly, check
the two tape drive controller LEDs.

8 to 4

The problem is in the module in the slot number
displayed.

The problem is in the module in slot 1, 2, or 3.
Check the graphics module LEDs. The green LED
on each module turns on if the module is operating
correctly.
If a module has a problem, the red LEDs on the graphics
frontplane display an error code. Sometimes the tests
cannot isolate the single failed module. In that case,
the LEDs identify the two or three most probable failed
modules. See Appendix F for an explanation of graphics
frontplane LED displays.

2–16 Testing and Troubleshooting

2.2.5 Running Self-Tests on Individual Modules
To run a self-test on an individual module, type
T mid [dev] [arg-1] [arg-2] [arg-3] . . .
The mid parameter represents the M-bus ID of the individual module you
are testing.
The optional dev parameter represents a specific device within a module.
Use the T 50 mid configuration display to find the device’s number.
The optional extended arguments (arg-1 and so on) specify individual
tests and test conditions. To run a specific test on a module or device,
type the number of the desired test.
The use of other extended arguments differ for each module. If you do
not include any arguments, the workstation performs all self-tests for the
module or device specified in the test command. The self-test information
sections later in this chapter explain the extended arguments for each
module.

2.2.6 Setting Loops for Self-Tests
In field service mode, you can specify self-tests to loop until they fail or
succeed.
•

Loop on test causes the test to continue repeating until it detects an
error. To specify loop on test, type T 200 1 and press Return . The
following display appears on the monitor:
MODE=FS LOT
CPUxx >>>

•

Loop on error causes the test to repeat until the test succeeds. To
specify loop on error, type T 200 2 and press Return . The following
display appears on the monitor:
MODE=FS LOE
CPUxx >>>

To stop a looping test, press Ctrl C . Then type T 200 0 and press Return .
The following display appears on the monitor:
MODE=FS
CPUxx >>>

Testing and Troubleshooting 2–17

2.3 Using System Tests
The system test checks each module separately, then operates the modules
together. This module interaction and repeated cycling help find system
problems and intermittent failures that the self-test might not detect.

2.3.1 Running System Tests
You can run two types of system test, depending on the test mode.
•

In customer mode, the system test runs an extensive check of the
system. Customer mode does not requires loopback connectors.

•

In field service mode, the system test includes some tests not run in
customer mode. Field service mode requires loopback connectors.

The customer mode system test completes two test cycles, then stops. To
run the customer mode system test, type T 100 and press Return . The
system test executes, then displays test results on the monitor.
Field service mode runs either auto-stop or continuous system tests.
•

To run an auto-stop field service test, type T 101 and press Return .
The system test runs for two cycles, then stops. Any error information
then appears on the screen.

•

To run a continuous field service test, type T 102 and press Return .
The system test repeats continuously. To stop a continuous system
test, press Ctrl C .

CAUTION
System tests can alter data on the tape or optical compact disc
drive. If the system test involves these devices, insert a scratch
tape in the TK70 tape drive and a test disc in the RRD40 optical
compact disc drive before performing a system test.

2.3.2 Setting Up Special System Tests
To select specific modules for a system test, type T 106 and press Return .
The screen displays a list of modules and devices you can include in the
test cycle. At each choice in the list, type 1 to include an item or 0 to
leave out an item. The default setting is 0.
The T 106 test is always continuous and runs only in field service mode.
If the test selection does not include DZ, press the Halt button to stop the
test.

2–18 Testing and Troubleshooting

To stop a T 106 test that includes DZ, you must stop each portion of the
test individually. Press Ctrl C to stop each test.

2.3.3 Displaying System Test Results
The monitor displays system test results. Example 2–5 shows a sample
system test display.
KA60-A VO.3
7
5
5
5

GFX
DZ
NI
SCSI

CU 0 00:28:41

3,2 MEMORY
?? 0
TQK70

0000.0001 37 0 00:24:32 34
0000.0001 45 0 00:25:00 20
0000.0001 40 0 00:26:43 23
70E5.0001 57 0 00:26:58 147
4103.0308
0067.0001 52 0 00:26:38 32
052F.2200 20 0 00:17:32 09

Example 2–5

Sample System Test Error Display

The top line lists the system’s test mode—either CU for customer mode or
CS for field service mode.
The top line also shows the total time this test has run. Time displays
use the format dd hh:mm:ss, where dd indicates days, hh indicates hours,
mm indicates minutes, and ss indicates seconds.
The left column displays an error indicator:
•

Two question marks (??) indicate a fatal error.

•

One question mark (?) indicates a nonfatal error.

•

No question mark indicates no error.

Each row in the display lists
•

The mid number of the module being tested

•

A description of the module or device

•

An eight-digit error message

•

The total number of test passes made on the module in this test

•

The time of the last test pass

A small letter s appears at the end of an error message if there is an
extended information summary. Error code explanations at the end of
this chapter discuss the extended information summaries that appear
with some error codes.

Testing and Troubleshooting 2–19

The system holds these extended information summaries in a wraparound stack. After the system test stops, the next extended summary in
the stack appears each time you press Return . Enter an exclamation point
(!) to exit the extended summary displays.
To bring back a display that has left the screen, type T 107 and press
Return . The system test results reappear on the screen.
Later in this chapter, maps explain system test error codes.

2.4 Troubleshooting the Monitor
Monitor tests verify that the monitor is operating correctly.
NOTE
Whenever you reconnect the video cable, use the monitor color
check tests to be sure the cable ends are connected in the correct
order.
Perform an UNJAM operation to clear the graphics registers before
running a monitor test.
To run a monitor test, type UNJAM and press Return . Then type T 7 1
[mt#] and press Return again.
The optional mt# parameter represents the number of the monitor test
you wish to run. Table 2–4 lists monitor test numbers and their uses.
If you do not specify a monitor test number, this command executes all
monitor tests.
Table 2–4 Monitor Test Numbers
Test Number

Monitor Display

100

White color

101

Red pattern

102

Gray bar pattern

103

Color bar pattern

104

Circle-crosshatch pattern

105

Coherent halftone pattern

106

Red color

107

Green color

2–20 Testing and Troubleshooting

Table 2–4 (Cont.) Monitor Test Numbers
Test Number

Monitor Display

108

Blue color

109

Black rectangle pattern

10A

Four-color bar pattern

10B

Letter E pattern

Use the controls on the side of the monitor to adjust brightness and
contrast. If the display appears distorted, press and hold the degauss
button and wait 10 seconds for the monitor to clear. Refer to the monitor’s
maintenance guide for more detailed information about repairing the
monitor.

2.5 Troubleshooting Mass Storage Devices
Workstation tests also check the TK70 tape drive, the RZ55 and RZ56
disk drives, and the RRD40 compact disc drive operation. Refer to
each device’s maintenance guide for more detailed troubleshooting and
maintenance information.

2.5.1 Troubleshooting the TK70 Tape Drive
To check the TK70 tape drive operation, use one of the following:
•

Tape drive LED display

•

System test

•

T 10F read/write test

Tape drive LEDs quickly indicate the tape drive’s condition. See
Appendix F for an explanation of tape drive LED displays.
TQK70 system test includes a tape drive check. Interpret TQK70 system
test results and extended information summaries for information about
tape drive performance.
The T 10F read/write test performs a series of read and write operations
beteween the tape drive controller and tape drive. The monitor then
displays the test results. Error codes in these messages use the same
format as TQK70 error codes. See the system test error code explanations
later in this chapter to interpret read/write error messages.

Testing and Troubleshooting 2–21

CAUTION
The read/write test can alter existing data on a tape drive. Insert
a scratch tape cartridge before running this test.
The system must be in field service mode to run the read/write test. After
the system is in field service mode, type T 10F and press Return . The
system then asks you to confirm that you want to run the read/write test
before the test begins.

2.5.2 Troubleshooting the RZ55 Disk, RZ56 Disk, and the
RRD40 Optical Compact Disc Drives
The SCSI system test checks the RZ55, RZ56, and RRD40 operation.
The system test then reports the RZ55, RZ56, and RRD40 test results as
part of the SCSI error messages. SCSI extended information summaries
provide additional information about these devices on the SCSI bus.
Interpret the SCSI system test results to obtain information about these
drives’ operation.
LEDs on the RRD40 quickly indicate the compact disc’s condition. See
Appendix F for an explanation of RRD40 LEDs.

2–22 Testing and Troubleshooting

2.6 TEST Command Summary
Table 2–5 is a quick reference for all TEST (T) commands used in
troubleshooting.
Table 2–5 TEST Command Summary
TEST
Command

Purpose

T 7 1 [mt]

Run the monitor test. The optional mt parameter indicates a
specific monitor test number. The system performs all monitor
tests if you do not specify a test number.

T mid [dev]

Perform the self-test on the module specified by mid. Include
an optional dev number to test only the device with that dev
number.

T 50 [mid]

Display system configuration and self-test results. Include an
optional mid number to display information about the module
with that mid number.

T 100

Perform the system test in customer mode.

T 101

Perform the auto-stop field service test.

T 102

Perform the continuous field service test.

T 106

Perform the selected system tests in Field Service mode.

T 107

Display system test results.

T 200

Set the system to customer or field service mode.

T 200 0

Remove test loops.

T 200 1

Set the self-test to loop on test.

T 200 2

Set the self-test to loop on error.

T 10F

Perform the read/write test on TK70 tape drive.

T01

Perform the test on the DWFQA Q-bus adapter module.

T02

Perform the test on the first Q-bus option listed in T 50 0.

T03

Perform the test on the second Q-bus option listed in T 50 0.

T04

Perform the test on the third Q-bus option listed in T 50 0.

Testing and Troubleshooting 2–23

2.7 Interpreting Self-Test Error Messages
The following sections explain self-test error codes and identify the FRUs
indicated by each error code.
Error codes differ for different modules and devices. There is a separate
section for each module and device error code format.

2.7.1 I/O Self-Test Error Messages
The self-test I/O error display provides a separate message for each I/O
device. Example 2–6 shows a sample I/O self-test error display.

1
2
3
4
5

01010004

L2003

SSC
DZ
NI
SCSI
SYS

00000001
00000001
19210770
00000901
00000001

Example 2–6

V1.1

Sample I/O Self-Test Display

The top line lists the module’s ID, type, name, and slot number. Question
marks appear if the self-test detected an error in an I/O device. The ROM
version number appears on the far right of this line.
Rows after the first line list the ID number, name, and current error
information for each device. Rows for devices that report errors also
include a question mark.
If the self-test does not detect a problem in a device, the self-test assigns
the code 00000001. Failed devices receive a specific error code. This
sample display reports an error in the network interface (NI).
NOTE
If you replace the I/O module, be sure to insert the Ethernet
address chip from the old I/O module onto the new I/O module.
This is necessary to retain the Ethernet address. See Figure 4–2
for the chip’s location.

2–24 Testing and Troubleshooting

2.7.2 SCSI Self-Tests
The small computer system interface (SCSI) self-test checks the SCSI
controller and verifies bus operation. The SCSI self-test does not check
the RZ55 disk, RZ56 disk, or the RRD40 compact disc drives. Use the
system test or an appropriate SCSI utility to isolate problems with these
devices.
Use SCSI utility commands to set system conditions for SCSI tests. See
Appendix F for an explanation of using SCSI utilities.
Altering data on a SCSI device is not normally allowed in customer mode;
you must intentionally use utility command T mid 4 1FF to enable write
operations in customer mode.
Write operations are always enabled in field service mode. However, these
commands warn that you may destroy data and ask you to confirm them
before proceeding. See Appendix F for detailed information about Utility
1FF.
To stop a test or utility, press Ctrl C . The monitor diplays the warning
code WRN$CTRLC.
If you interrupt the operating system or a SCSI utility, you do not need to
do an UNJAM before issuing a SCSI utility command.
SCSI self-test error codes have the following format:
x

x
Severity Level
Error Code
Test Number
Error Number
Error Group

The severity level indicates the seriousness of the error.
The error code is a code for the actual failure.
Table 2–6 explains possible error code and severity level combinations in
SCSI error messages.

Testing and Troubleshooting 2–25

The test number is the number of the failed test. See Appendix F for an
explanation of the individual SCSI test numbers.
The error group and error number refer to the software calling out the
error. These codes are not explained in this manual.
Here are some sample SCSI error codes:
•

The error code 00000001 means the self-test did not detect any errors.

•

The error code 01240922 means error number 24 in error group 01
found error 2, with a severity level of 2, in test 09.

2.7.2.1 Probable Failed FRU
Use the test number in the SCSI error code to determine the probable
failed FRU.
•

A test number from 0 to 8 indicates a failure in the I/O module.

•

A test number greater than 8 indicates a failure in the SCSI bus.
Disconnect the SCSI connector from the I/O module and repeat the
self-test. If the self-test still reports an error with a test number
greater than 8, the problem is probably in the I/O module. If the selftest does not report an error when SCSI is disconnected from the I/O
module, the problem is probably in the SCSI bus.

2.7.2.2 SCSI Self-Test Error Codes
Table 2–6 explains possible SCSI error codes.
Table 2–6 SCSI Error and Severity Messages
Code

Meaning

The test or utility ended successfully.

Ctrl C aborted the test or utility.

An SII register had an incorrect value. The extended status
string has the following format:
regnamnn/cccc!=eeee
regnam

Represents the register from the SII specification.

Represents the offset to the register from the
base of the SII register space.

cccc

Represents the current register contents.

eeee

Represents the expected register contents.

2–26 Testing and Troubleshooting

Table 2–6 (Cont.) SCSI Error and Severity Messages
Code

Meaning

The RAM buffer contained an incorrect value. The extended
status string is in the format:
RAMnnnnn/cccccccc!=eeeeeeee
RAM

Indicates this is a RAM comparison.

nnnnn

Represents the offset into the SII RAM buffer.

cccccccc

Represents the current RAM location.

eeeeeeee

Represents the expected RAM location.

The SII chip or SCSI bus did not change to the expected state.
The extended information string uses the same format as the
string for error and severity code number 22.

The SII chip or SCSI bus did not change to the expected state
within the allotted time. The extended information string has
the same format as the string for error and severity code number
22.

The diagnostic executive failed to allocate the requested
temporary storage space, so the typed command was not
executed.

A machine check occurred during testing. The extended
information string has the following format:
MCHK=nn, PC=ppppppp, VA=aaaaaaaa

Represents the machine check code.

ppppppp

Represents the program counter when the
machine check occurred.

aaaaaaaa

Represents the virtual address when the machine
check occurred.

vvvvvvvv

Represents the processor status longword when
the machine check occurred.

An illegal parameter was entered. The extended status string
indicates the incorrect parameter. Argument 1 is the test
number, and argument 2 is usually the unit number. The unit
number is the SCSI ID number multiplied by 100. Use the
Show SCSI utility described in Appendix F to display SCSI ID
numbers. The use of argument 3 depends on the test or utility
being executed.

Testing and Troubleshooting 2–27

Table 2–6 (Cont.) SCSI Error and Severity Messages
Code

Meaning

The mode is invalid. A test that can alter user data was
attempted in customer mode, but write operations were not
enabled. This code is generated for any device with a block size
larger than 8 Kbytes.

The bus failed the external loopback test, a loopback connector
was present when a SCSI device operation was attempted, or a
device on the SCSI bus has the same SCSI ID as the SII chip.
Do not try further operations on the SCSI bus if this error code
appears.

You tried to access a nonexistent SCSI ID or logical unit number
on an existing SCSI ID.

The addressed SCSI device is not ready to accept the specified
command. Usually, this means a disk has not been spun up.

Data returned by the SCSI device was not consistent or expected.
Associated sense information appears in the format:
SNS=n, [ASNS=mm], [INF=iiiiiiii]
n

Represents the sense value returned by the
REQUEST SENSE SCSI command.

Represents a possible additional sense code.

iiiiiiii

Represents the information bytes.

Table 2–7 lists possible sense codes values.
E2

One of the following signals was asserted on the SCSI bus:
RST

SCSI bus reset

BER

SCSI bus error

IPE

SCSI bus parity error

OBC

Unused DSSI bits

BUF

Unused DSSI bits

LDN

Unused DSSI bits

2–28 Testing and Troubleshooting

2.7.2.3 SCSI Extended Information Messages
Extended information strings often appear after the first error message
line and provide additional information about the device’s condition.
These extended information strings frequently use the following symbols:
•

A question mark (?) indicates that a value or condition is incorrect or
unknown. For example, the string ARG1(56), TSTNUM? indicates that
56 is an incorrect test number for argument 1.

•

An equal sign (=) indicates a value or state. For example, BUS=LBK
indicates that the SCSI bus is in the loopback state. BUS=? indicates
that the bus state is unknown.

•

An exclamation point and equal sign together (!=) indicate that a
value or condition is not equal to the desired value, as is common in
parameter errors and data comparison errors.

2.7.2.4 Sense Code Values
Some extended information strings list sense code values. Sense code
information strings have the following format:
SNS=n, [ASNS=mm], [INF=iiiiiiii]
where n represents the sense key, mm represents an additional sense
code, and iiiiiiii represents the information.
Table 2–7 defines sense code values found in SCSI extended information
strings.
Table 2–7 Sense Code Values
Code

Meaning

No sense. The command was successful. This value indicates an error
if it is returned after a check condition.

Recovered error. The last command was successful, but the device
performed some recovery action.

Not ready. The device cannot be accessed.

Medium error. The device detected a nonrecoverable error condition,
probably caused by a flaw in the medium or an error in the recorded
data.

Hardware error. The device detected a nonrecoverable hardware
failure.

Testing and Troubleshooting 2–29

Table 2–7 (Cont.) Sense Code Values
Code

Meaning

Illegal request. The device detected an illegal parameter in the
command descriptor block.

Unit attention. A removable medium was changed, the target was
reset, or mode select parameters were changed by another initiator.

Data protect. A read or write was attempted on a block protected from
this operation.

Blank check. A write-once, read-multiple or sequential access device
encountered a blank medium or end-of-data indication while reading,
or a write-once, read-multiple device encountered a nonblank medium
while writing.

Vendor unique.

Copy aborted. An error on the source or destination device caused the
system to abort a copy, compare, or copy and verify command.

Aborted command. The device aborted the command.

Equal. A search data command satisfied an equal comparison.

Volume overflow. A buffered peripheral device reached the end of the
medium. Data not written to the medium may remain in the buffer.

Miscompare. The source data did not match the data read from the
medium.

Reserved.

Refer to the ANSI SCSI specification or the device’s documentation for
more information about sense code information strings.

2–30 Testing and Troubleshooting

2.7.3 System Support Chip (SSC) Self-Tests
SSC error codes have the following format:
0

x
Severity Level
Error Code
Test Number

The severity level indicates the seriousness of the error, as follows:
0

Warning

No error

Error

Fatal error

The error code identifies the specific error.
The test number is the number of the failed test.
SSC error codes do not use the four digits on the left. These digits are
always 0.
Here are some examples of SSC error codes:
•

Error code 00000001 means the self-test did not detect an error.

•

Error code 00000632 means error number 3, with a severity level of 2,
occurred in test 6.

See Appendix F for a detailed description of individual SSC self-tests.
2.7.3.1 Probable Failed FRUs
All SSC error codes indicate a failed I/O module, except in the following
cases :
•

Error code 00000622 indicates a failed I/O or CPU module.

•

Error code 00000722 indicates a failed I/O module or failed battery.

Testing and Troubleshooting 2–31

2.7.4 Serial Line Adapter (DZ) Self-Tests
DZ self-test error codes have the following format:
x

x
Severity Level
Nonline Error
Test Number
Line 0 Error
Line 1 Error
Line 2 Error
Line 3 Error

The severity level indicates the seriousness of the error.
The nonline error code identifies failures that are not specific to one line.
The test number is the number of the failed test. The test number is 0 if
the test itself is invalid.
The four line error digits on the left report errors occurring in the
individual line represented by the corresponding position in the error
code.
Here are some examples of DZ error codes:
•

Error code 000000001 means that all lines passed the self-test.

•

Error code 00030502 means error number 3, with a severity level of 2,
occurred on line 0 in test number 5.

2–32 Testing and Troubleshooting

2.7.4.1 Probable Failed FRUs
Specific failed tests indicate different failed FRUs. Table 2–8 lists the
probable failed FRUs indicated by each failed test.
Table 2–8 Failed FRUs Indicated by DZ Error Codes
Test
Number

What the Test
Checks

Transmission and
reception

I/O module

Internal baud rate

I/O module

Internal character
length

I/O module

Internal parity

I/O module

Internal stopbit

I/O module

External baud rate

I/O module, I/O cover, or missing
loopback connector

External character
length

I/O module, I/O cover, or missing
loopback connector

External parity

I/O module, I/O cover, or missing
loopback connector

External stopbit

I/O module, I/O cover, or missing
loopback connector

Silo alarm bit
functionality

I/O module

Silo cell

I/O module

Silo alternating lines

I/O module

Overrun bit
functionality

I/O module

Transmit interrupt

I/O module

Receive interrupt

I/O module

Break functionality

I/O module

Console (IOCSR)
break

I/O module

Modem loopback
connector

I/O module, I/O cover, or missing
loopback connector

Probable Failed FRU

Testing and Troubleshooting 2–33

Table 2–8 (Cont.) Failed FRUs Indicated by DZ Error Codes
Test
Number

What the Test
Checks

Probable Failed FRU

Keyboard

Keyboard, I/O cover, or I/O module

Mouse

Mouse, I/O cover, or I/O module

2.7.4.2 DZ Error Codes
Table 2–9 and Table 2–10 list DZ error codes. Error code values for test 0
are different than error code values for nonzero test numbers.
Table 2–9 DZ Error Codes for Test Number 0
Code

Meaning

0
1
2
3
4

No error.
Mode bits are invalid.
The TEST command received the wrong number of arguments.
The TEST command passed an invalid test number argument.
The test will not run in the current mode.

Table 2–10 DZ Error Codes for Nonzero Tests
Code

Meaning

0
1
2
3
4
5
6
7
8

No error.
Master-clear timeout.
Transmitter-ready timeout (txchar error).
Receiver done timeout.
Parity error for received character.
Frame error for received character.
Overrun error for received character.
Received data is not valid.
Expected character is not equal to received character.

2–34 Testing and Troubleshooting

2.7.5 Network Interface (NI) Self-Tests
NI error codes have the following format:

Pass/Fail
Test Number

Pass/fail indicates whether a test failure occurred. This code is 01 if the
test passed and x0 if a test failed, where x is the same number as the test
number.
The test number is the number of the failed test.
NI error codes do not use the five digits on the left.
Here are some examples of NI self-test codes:
•

Error code 00000301 means no error occurred in test number 3.

•

Error code 00000331 indicates test number 3 failed.

2.7.5.1 Probable Failed FRU
Error codes 110 through 660 indicate a problem in the I/O module. Error
code 770 indicates a problem in the I/O cover or its connecting cable.
NOTE
If an NI self-test logs an error, check the Ethernet switch first.
NI connects the workstation to a ThickWire or ThinWire Ethernet. The
system shows an error if the Ethernet switch is not set for the connection
or terminator being used. For the NI self-test to succeed, the Ethernet
switch setting must be correct.

Testing and Troubleshooting 2–35

2.7.5.2 NI Error Codes
Table 2–11 explains possible NI error codes.
Table 2–11 NI Error Codes
Code

Meaning

00000110
00000220
00000330
00000550
00000660
00000770

NI RAM buffer test failed.
NI RAM registers test failed.
NI internal loopback promiscuous mode test failed.
NI internal loopback append CRC test failed.
NI internal loopback address filter mode test failed.
NI external loopback test failed.

2–36 Testing and Troubleshooting

2.7.6 CPU Self-Tests
CPU self-test error codes have the following format:
x

Test Number

The test number is the number of the failed test.
The meaning of other error code numbers depends on the individual error
code.
2.7.6.1 Probable Failed FRU
CPU error codes indicate a faulty CPU.
2.7.6.2 CPU Test Numbers and Error Codes
Table 2–12 lists CPU self-test numbers.
Table 2–12 CPU Self-Test Numbers
Test Number

What the Test Checks

01
02
03
04
05
06
07
81
82

CFPA
CPU virtual mode
FBIC interrupt (MIRQ/CIRQ)
C-bus parity
CPU cache 1
FBIC M-bus test modes (power-up only)
CPU ROM checksum
FBIC cache counters (power-up only)
CPU virtual mode (power-up only)

Table 2–13 lists possible CPU error codes grouped by test number.

Testing and Troubleshooting 2–37

Table 2–13 CPU Self-Test Error Codes
Code

Meaning

Test 01
00010104
00020104
00030104
00040104
00050104
00060104
00070104
00080104
00090104
000A0104
000B0104
000C0104
000D0104

MNEGD failed.
CVTFL failed.
CVTLF failed.
CVTLG failed.
CVTLD failed.
ADDF3 failed.
MULF3 failed.
DIVF3 failed.
POLYF failed.
Did not get expected reserved operand fault in MOVF.
Error in underflow test.
Error in overflow test.
Error in divide-by-zero test.

00010114
00020114

Unexpected reserved operand fault.
Unexpected arithmetic exception fault.

Test 02
00010204
00020204
00030204
00040204
00050204
00060204
00070204

No memory to run test.
Translation buffer error.
Data mismatch across page boundary.
Page not marked as modified when expected.
Did not get length access violation when expected.
Did not get write access violation when expected.
Did not get expected translation violation.

00010214
00020214
00030214
00040214
00050214

Unexpected interrupt or exception.
Invalid data for expected access violation
Invalid data in translation-not-valid fault handler.
Unexpected access violation.
Unexpected translation-not-valid fault.

Test 03
00010302
00020302
00030302

Interrupt pending at given IPL. Examine IPDVINT.
Interrupt never received. Check FBICSR.
Interrupt pending, but not acknowledged.

2–38 Testing and Troubleshooting

Table 2–13 (Cont.) CPU Self-Test Error Codes
Code

Meaning

00010312

Interrupt received at unexpected vector.

Test 04
00010404
00020404
00030404
00040404
00050404

Unexpected machine check.
Did not get expected machine check; longword read.
Did not get expected machine check; word read.
Did not get expected machine check; byte read.
Machine check occurred even though parity checking was off.

00010414
00020414
00030414
00040414

Byte count in machine check frame not 16.
Not a machine check 80 (read).
Unused.
CDAL parity error not flagged in saved MSER. Check the CPU.

Test 05
00010514
00020514
00030514

CADR failed read/write test.
Dialog mode: read/write miscomparison.
Dialog mode: MSER detected cache miss (should have hit).

00010524
00020524
00030524
00040524
00050524
00060524
00070524
00080524

Address shorts: cache miss or other memory error (LW0).
Address shorts: data miscomparison (LW0).
Address shorts: cache miss or other memory error (LW1).
Address shorts: data miscomparison (LW1).
Address shorts: cache miss or other memory error (LW0).
Address shorts: data miscompare (LW0).
Address shorts: cache miss or other memory error (LW1).
Address shorts: data miscomparison (LW1).

Test 06
00010644
00020644
00030644
00040644
00050644
00060644
00070644
00080644

Did not get expected machine check. Complement MCMD parity.
Not all FBICS logged MCPE.
Did not get expected machine check. Complement MDAL parity.
Not all FBICS logged MDPE.
Did not get expected machine check. Complement MCMD valid.
Not all FBICS logged ICMD.
Not all FBICS frozen on generated MABORT.
Unused.

Testing and Troubleshooting 2–39

Table 2–13 (Cont.) CPU Self-Test Error Codes
Code

Meaning

00090644

Did not get expected machine check. Complement MSTATUS
parity.

00010654

Unexpected machine check.

Test 81
000x8104

Read miscomparison.x is the number of the failing byte.

2.7.7 Memory Self-Tests
Table 2–14 lists possible memory self-test error codes.
Table 2–14 Memory Error Codes
00000001
0000FFF4
xxxx0104
FF010304
FF020304
44440444
44440440
00000002

No error detected.
Could not find any good memory.
Failed checkbits in mode 1.xxxx represents the failing checkbit.
Failed DRAM state machine signature test.
Failed M-bus state machine signature test.
Timeout waiting for module self-test to complete.
Bad sections of memory were found by BIST.
Too many bad pages.

2.7.7.1 Probable Failed FRU
A memory self-test error code indicates a faulty memory module.

2–40 Testing and Troubleshooting

2.7.8 Graphics Self-Tests
Graphics self-test error codes have the the following format:
x

x
Severity Level
Error Code
Test Number
Failed−Chip Code
Failed−FRU Code

The severity level indicates the seriousness of the error.
The error code identifies the specific error that occurred.
The test number is the number of the failed test.
The failed-chip code indicates the problem chip in the failed module.
The failed-FRU code indicates the probable failed FRU.
Table 2–15 lists severity level values.
Table 2–15 Graphics Severity Levels
Code

Meaning

0
1
2
3
4
5
6
7

Warning
Success
Error
Information message
Severe error
Reserved
Reserved
Reserved

Testing and Troubleshooting 2–41

2.7.8.1 Probable Failed FRU
The failed-FRU code identifies the probable failed FRU. Values between
0 and 7 indicate specific problem modules. Values from 8 to C indicate
general system failures.
The graphics self-test does not always single out one problem module, but
may indicate two or three possible problem modules.
Table 2–16 lists possible failed FRUs.
Table 2–16 Graphics Failed-FRU Error Codes
Value

Faulty FRU

0
1
2
3
4
5
6
7
8
9
A
B
C
D

No error
Graphics base module
Graphics output module
Graphics base or output module
Graphics expansion module
Graphics expansion or base module
Graphics expansion or output module
Graphics base, output, or expansion module
Bad configuration
Restart code error
Unexpected interrupt
VDAC comparator error
CPU timeout
Insufficient resources (Fault is outside the graphics subsystem.)

2.7.9 Tape Adapter and Tape Drive Controller Self-Tests
The system reports failures in the tape adapter module and TQK70 tape
drive controller as tape adapter failures.
This section lists each error code separately rather than provide a map,
because there are relatively few tape adapter and tape drive controller
error codes. Table 2–17 lists tape adapter module error codes. Table 2–18
lists tape drive controller error codes.
NOTE
The self-test does not check the tape drive. To check the tape
drive, use system tests or the T 10F command.

2–42 Testing and Troubleshooting

Table 2–17 Tape Adapter Module Error Codes
Code

Meaning

00000100
00000200
00000400
00000003
00000002
00000004
00FF0104

FBIC register miscomparison.
FBIC register verification error.
Doorbell interrupt error.
No Q-bus devices found by sniffer.
CQBIC fatal error on Q-bus read access.
Error during sniff.
Sniffer could not allocate memory.

Table 2–18 TQK70 Self-Test Error Codes
Code

Meaning

00000001

The controller successfully completed its power-up self-test. No
error was detected.

00000012

System was unable to initialize controller after two attempts.

00000022

Controller reported an error in the initialization step.

00000112

Controller timeout occurred in step 1 of the initialization
sequence.

00000122

Controller found an error in step 1 of the initialization sequence.

00000132

Controller did not interrupt after completing step 1 of the
initialization sequence.

00000212

Controller timeout occurred in step 2 of the initialization
sequence.

00000222

Controller found an error in step 2 of the initialization sequence.

00000232

Controller did not interrupt after completing step 2 of the
initialization sequence.

00000312

Controller timeout occurred in step 3 of the initialization
sequence.

00000322

Controller found an error in step 3 of the initialization sequence.

00000332

Controller did not interrupt after completing step 3 of the
initialization sequence.

00000632

Error occurred in allocating system memory.

00000642

Controller did not get a successful response to deallocate memory
instruction.

Testing and Troubleshooting 2–43

Table 2–18 (Cont.) TQK70 Self-Test Error Codes
Code

Meaning

00000922

Controller failed to clear the memory’s DMA area.

2.7.9.1 Probable Failed FRUs
Tape adapter module errors codes indicate a failed tape adapter.
TQK70 errors almost always indicate a failed tape drive controller.
However, a few error codes indicate a second possible cause for the failure:
•

Error code 00000022 indicates a possible fault in the controller or a
reversed tape drive connector cable. The tape drive connector has
labels on each end that show which connector side faces out. Be
sure these ends are connected correctly before replacing the TQK70
module.

•

Error codes 00000632 and 00000642 indicate a possible problem in
the memory module. Check the memory module before replacing the
TQK70.

•

The tape adapter module is also a possible cause of any error listed as
a TQK70 error. If replacing other TQK70 devices fails to correct the
fault, replace the tape adapter module.

2.7.10 DWFQA Q-bus Adapter and Q-bus Option Self-Tests
Table 2–19 lists fatal error codes for the DWFQA Q-bus adapter self-test.

Table 2–19 DWFQA Q-bus Adapter Self-Test Error Codes
Code

Test

Error

Meaning

00000114

Fatal: Failure accessing FBIC registers.

00000124

Fatal: Failure accessing SAVGPR FBIC
register.

00000214

Fatal: Failure testing FQAM CSR.

00000314

Fatal: Failure testing the data path to
scatter/gather map.

00000324

Fatal: Failure testing the address path
to scatter/gather map.

2–44 Testing and Troubleshooting

Table 2–19 (Cont.) DWFQA Q-bus Adapter Self-Test Error Codes
Code

Test

Error

Meaning

00000334

Fatal: Failure testing the address line
(short/open) to scatter/gather map.

00000344

Fatal: Failure testing the data cell
integrity of scatter/gather map.

00000414

Fatal: Failure testing pushs/pops in
longword count FIFO.

00000424

Fatal: Failure testing data patterns in
longword count FIFO.

00000514

Fatal: Failure testing the address/data
FIFO ( read bad pattern ).

00000614

Fatal: Failure testing the path from
the scatter/gather map to address/data
FIFO.

00000714

Fatal: Failure testing the address/data
FIFO dump. Dumped to incorrect
address ( lower than it should have ).

00000724

Fatal: Failure testing the address/data
FIFO dump. Dumped to incorrect
address (higher than it should have).

00000734

Fatal: Failure testing the address/data
FIFO dump. Bad pattern read back.

00000814

Fatal: Failure testing bytemask
generation. Bytemask is incorrect.

2.7.10.1 CXY08 Self-Test Error Codes
CXY08 self-test errror codes have the following format:
SSSS.EEEE
EEEE is a specific error code indicating a problem was found while
running the test or with the device.
SSSS displays status information about the device. The CXY08 has two
modes of operation, DHU and DHV, which are supported by this code.
The DHU is the preferred mode of operation for the CXY08. The code
only displays status information if the device is operating in DHV mode.

Testing and Troubleshooting 2–45

Table 2–20 lists the possible error codes for the CXY08 module.
Table 2–20 CXY08 Self-Test Error Codes
Code

Meaning

EEEE
0001

CXY08 successfully passed the self-test.

0112

Reset flag cleared too quickly after the reset command was
issued. (May not have run tests, or command was not received
by the device.)

0122

Timed out while running Reset command ( internal diagnostics ).

0132

Internal diagnostics reported an error.

0212

TX.ACTION bit not set to indicate DMA happened in allowed
time.

0222

No interrupt received to signal DMA complete.

0232

Error in data received, RX buffer did not match TX buffer.

0412

TX.ACTION and/or RX.AVAILABLE bits not set to indicate the
character was transmitted and received.

0422

RX character invalid: DHV mode, single character transfer, RX
character not the expected value.

0432

No interrupt received to signal new data in RX FIFO
( DHV mode ).

0512

CXY08/FQAM scatter/gather map access failure
( shorted address lines ).

0632

Error allocating system memory for use by this test.

0642

Error deallocating system memory used by this test.

0ff2

Unexpected interrupt occured while the running the CXY08 test.

SSSS
xC08

The CXY08 is in DHU mode ( switch setting ).

xD11

The CXY08 is in DHV mode ( switch setting ).

0xxx

No unexpected interrupt occurred during the running of this test.

100x

An unexpected interrupt occured while running the CXY08 test.

2–46 Testing and Troubleshooting

2.7.10.2 DSV11 Self-Test Error Codes
DSV11 self-test error codes have the following format:
SSSS.EEEE
EEEE is a specific error code indicating a problem was found while
running the test or with the device.
SSSS displays status information about the device or test. Table 2–21
lists the self-test error codes for the DSV11 module.
Table 2–21 DSV11 Self-Test Error Codes
Code

Meaning

EEEE
0001

DSV11 successfully passed the self-test.

0212

Did not skip the self-test—DSV11 returned the incorrect status
from command. Reset with skip self-test bit set.

0222

RSP bit not set—the command issued expected to set the bit, but
it was not set within the allowed time.

0232

No interrupt received—the command issued expected an
interrupt to be generated.

0312

Error allocating system memory—DE$A_allocate reported
a problem allocating system memory for use by this test
( TX buffer ).

0322

Error allocating system memory—DE$A_allocate reported
a problem allocating system memory for use by this test
( RX buffer ).

0332

RSP bit not set—the command issued expected the bit to be set,
but it was not set within the allowed time.

0342

TX command reported an error—the transmit data command
reported a failure.

0362

RX buffer does not equal the TX buffer—DSV11 failed to
complete DMA.

0372

Error deallocating RX buffer—DE$A_Deallocate reported a
problem deallocating system memory used by this test.

0382

Error deallocating TX buffer—DE$A_Deallocate reported a
problem deallocating system memory used by this test.

Testing and Troubleshooting 2–47

Table 2–21 (Cont.) DSV11 Self-Test Error Codes
Code

Meaning

EEEE
0632

Error allocating system memory—DE$A_allocate reported a
problem allocating system memory for use by this test.

0642

Error deallocating system memory—DE$A_Deallocate reported a
problem deallocating system memory used by this test.

0ff2

Unexpected interrupt occurred while the running the DSV11 test.

SSSS
0000

No unexpected interrupt occurred during the running of this test.

1000

An unexpected interrupt occurred.

2.7.10.3 TSV05 Self-Test Error Codes
TSV05 self-test error codes have the following format:
SSSS.EEEE
EEEE is a specific error code indicating a problem was found while
running the test or with the device.
SSSS displays status information about the device.
Loopbacks are required for Customer Services and Manufacturing modes,
but not for customer mode. Table 2–22 lists the self-test error codes for
the TSV05 module.
Table 2–22 TSV05 Self-Test Error Codes
Code

Meaning

EEEE
0112

System did not accept reset in two attempts.

0122

Subsystem ready bit not set in allowed time.

0132

Subsystem ready bit cleared when should be set

0212

Sanity check error, device detects an internal failure.

0222

2–48 Testing and Troubleshooting

Table 2–22 (Cont.) TSV05 Self-Test Error Codes
Code

Meaning

EEEE
0232

Nonexistent memory, CMD, CHR or MSG buffer not found or
recognized.

0242

NBA bit set, supplied MSG buffer address not accepted.

0252

Unexpected error reported.

0262

Interrupt did not occur within allowed time.

0ff2

Unexpected interrupt occurred, with the device passing the
self-test.

SSSS
1XXX

Unexpected interrupt occurred during the self-test.

2.8 Interpreting System Test Error Messages
System test error codes have the following format:
x

Error Code
Status Code

The error code identifies a specific error.
The status code may provide additional information about the system’s
condition. If no additional information is available, the four digits at the
left are 0s.
System test error codes indicate a probable failure in the module reporting
an error. If modules still report system test errors after you replace
related FRUs, contact Digital support service.
The following sections provide maps for system test error codes. Each
section also explains extended information strings that appear with each
error message.

Testing and Troubleshooting 2–49

2.8.1 System Test Exception Messages
If an exception occurs during a system test, the workstation kernel
displays several messages and halts all CPUs. The first message line
indicates the type of fault. The following message lines give exact
information about exception type and location. Table 2–23 lists system
test exception messages.
Table 2–23 System Test Error Messages
Message

Meaning

ker$mchk

Unrecoverable machine check.

exc pc

Represents exception program counter (PC).

exc psl

Represents exception program status longword (PSL).

ker$acc_vio

Access violation.

xxx

Represents an access violation reason mask. Possible bit
values:
Bit 0

Bit 1

Bit 2

1, if the PTE access code did not permit
intended access.

0, if p0lr, p1lr, or s0lr have a length
violation.

0, if the specified virtual address is not
accessible.

1, if the associated page table entry is not
accessible.

0, if a read access was intended.

1, if a modify access was intended.

acc vio vrt adr

Represents the access violation’s virtual address.

exc pc

Represents an exception PC.

exc psl

Represents an exception PSL.

2–50 Testing and Troubleshooting

Table 2–23 (Cont.) System Test Error Messages
Message

Meaning

ker$arth

Arithmetic trap or fault.

Represents an arithmetic exception code. Arithmetic
exception codes have one of the following values:
0

Undefined

Integer overflow

Integer divide by zero

Floating overflow trap

Floating divide-by-zero trap

Floating underflow trap

Decimal string overflow

Decimal string divide by zero

Floating overflow fault

Floating divide-by-zero fault

Floating underflow fault

exc pc

Represents exception PC.

exc psl

Represents exception PSL.

ker$breakpnt

Breakpoint fault.

exc pc

Represents exception PC.

exc psl

Represents exception PSL.

Testing and Troubleshooting 2–51

Table 2–23 (Cont.) System Test Error Messages
Message

Meaning

ker$comp

Compatibility mode fault.

Represents the compatibility exception code. The
compatibility exception code has one of the following values:
0

Reserved instruction execution

BPT instruction execution

IOT instruction execution

EMT instruction execution

Trap instruction execution

Illegal instruction execution

Odd address fault

Tbit trap

exc pc

Represents exception PC.

exc psl

Represents exception PSL.

ker$ker_stk

Kernel stack not valid.

exc pc

Represents exception PC.

exc psl

Represents exception PSL.

ker$cus_res

Opcode reserved for customer.

exc pc

Represents exception PC.

exc psl

Represents exception PSL.

ker$dig_res

Opcode reserved to Digital.

exc pc

Represents exception PC.

exc psl

Represents exception PSL.

2–52 Testing and Troubleshooting

Table 2–23 (Cont.) System Test Error Messages
Message

Meaning

ker$res_mde

Reserved addressing mode.

exc pc

Represents exception PC.

exc psl

Represents exception PSL.

ker$res_opr

Reserved operand.

exc pc

Represents exception PC.

exc psl

Represents exception PSL.

2.8.2 Machine Check Messages
If a machine check occurs during a system test, the workstation kernel
displays several messages and halts all CPUs. The first message line
describes the actual machine check error. The following message lines
give detailed information about the machine fault type and location.
Table 2–24 lists each machine check message and explains each message
line.
Table 2–24 Machine Check Error Messages
Message

Meaning

fpu mchk

Floating point errors.

Hexadecimal number of bytes in machine check log on stack.

typcde

Machine check type code:

rcntva

Protocol error detected FPA chip while attempting to
execute a floating point instruction: reserved instruction
execution.

Reserved instruction detected FPA while attempting to
execute a floating point instruction: IOT instruction
execution.

An error of unknown origin detected FPA.

Represents the most recent virtual address.

Testing and Troubleshooting 2–53

Table 2–24 (Cont.) Machine Check Error Messages
Message

Meaning

stat1

Represents internal state information 1.

stat2

Represents internal state information 2.

Represents exception PC.

psl

Represents exception PSL.

mmu mchk

Memory management errors.

Hexadecimal number of bytes in machine check log on stack.

typcde

Machine check type code:
5

The calculated virtual address for a process PTE was not
in the system space when the CPU attempted to access a
process PTE after a translation buffer miss.

The calculated virtual address for a process PTE was in
the P1 space instead of the system space when the CPU
attempted to access a process PTE after a translation
buffer miss.

The calculated virtual address for a process PTE was in
the P0 space instead of the system space when the CPU
attempted to access a process PTE, to change the PTE
M-bit before writing to a previously unmodified page.

The calculated virtual ddress for a process PTE was in
the P1 space instead of the system space when the CPU
attempted to access a process PTE, to change the bit
before writing to a previously unmodified page.

rcntva

Represents the most recent virtual address.

stat1

Represents internal state information 1.

stat2

Represents internal state information 2.

Represents exception PC.

psl

Represents exception PSL.

mda mchk

Microcode detected errors.

Hexadecimal number of bytes in machine check log on stack.

2–54 Testing and Troubleshooting

Table 2–24 (Cont.) Machine Check Error Messages
Message

Meaning

typcde

Represents machine check type code during a MOVC3 or MOVC5
instruction (not move forward, move backward, or fill.)

rcntva

Represents the most recent virtual address.

stat1

Represents internal state information 1.

stat2

Represents internal state information 2.

Represents exception PC.

psl

Represents exception PSL.

md9 mchk

Undefined interrupt ID.

Hexadecimal number of bytes in machine check log on stack.

typcde

Represents machine check type code. There is only one mda
machine check code:
9

A hardware interrupt was requested at an unused IPL.

rcntva

Represents the most recent virtual address.

stat1

Represents internal state information 1.

stat2

Represents internal state information 2.

Represents exception PC.

psl

Represents exception PSL.

Testing and Troubleshooting 2–55

Table 2–24 (Cont.) Machine Check Error Messages
Message

Meaning

rde mchk

Read errors.

Hexadecimal number of bytes in machine check log on stack.

typcde

Represents machine check code type:
80

An error occurred while reading an operand or a process
page table.
Entry during address translation, or any read generated
as part of an interlocked instruction.

An error occurred while reading one of these:
•

System page table entry during address translation

•

Process control block entry during a context switch

•

System control block entry while processing an
interrupt

rcntva

Represents the most recent virtual address.

stat1

Represents internal state information 1.

stat2

Internal state information 2.

Represents exception PC.

psl

Represents exception PSL.

wrt mchk

Write errors.

Hexadecimal number of bytes in machine check log on stack.

typcde

Represents machine check code type:

rcntva

An error occurred while writing an operand or a process
page table entry to change the PTE (M) bit before writing
a previously unmodified page.

An error occurred while writing a system page table
entry (SPTE) to change the PTE(M) bit before writing
a previously unmodified page, or a process control block
(PCB) during a context switch or during the executions
that modify and stack pointers in the PCB.

Represents the most recent virtual address.

2–56 Testing and Troubleshooting

Table 2–24 (Cont.) Machine Check Error Messages
Message

Meaning

stat1

Represents internal state information 1.

stat2

Represents internal state information 2.

Represents exception PC.

psl

Represents exception PSL.

2.8.3 Serial Line Adapter (DZ) System Test Error Messages
The DZ system test reports two types of errors, DZ device errors and
software errors.
•

DZ device errors indicate problems performing transfers through the
DZ.

•

DZ software error messages occur if the DZ system test receives a
failure message during a VAXELN kernel call.

DZ Device Error Messages
DZ device error messages have the following format:
0

.
Line 0 Error
Line 1 Error
Line 2 Error
Line 3 Error
DZ Line Used by the Console

The DZ line used by the console is represented by the nonzero digit in the
four digits at the left.
The line error codes indicate the line where the error occurred. An error
code in one of these places indicates the exact error that occurred in that
line.

Testing and Troubleshooting 2–57

Table 2–25 lists the DZ device system test error codes.
Table 2–25 DZ Device System Test Error Codes
Error

Meaning

0
2
3
4
5
6
7
8
9

Line check performed.
First character transmitted, but loopback was not received.
Transfer took too long to complete.
More characters have been received than expected.
Parity error occurred.
Framing error occurred.
Overrun error occurred.
Data compare error occurred.
Line failed to transmit all characters.

DZ Software Error Messages
DZ software error messages have the following format:
x

Returned Call
Failing VAXELN Status

The returned call indicates the specific call that returned the failure.
The failing VAXELN status appears in the four digits at the left.
The F to the right of the separator always appears in DZ software error
codes.
Table 2–26 lists software error messages for the DZ system test.

2–58 Testing and Troubleshooting

Table 2–26 DZ Software Error Codes
Error

Meaning

FF01

WST$_INIT call failed.

F004

Ctrl C area can not be obtained.

F005

Cannot attach to the DZ interrupt vector.

F006

DZ registers allocation failed.

F007

FBIC CSR allocation failed.

F008

Could not create line processing enable event.

F009

Could not create line processing finished event.

F00a

Could not create line processing.

F00b

Could not create Ctrl C processing enable event.

F00c

Could not create console input processing.

F00d

Could not create no printing in progress event.

F00e

Could not signal line processing enable event

F00f

Line processing did not complete successfully.

F010

Could not clear line processing finished event.

F011

Could not signal Ctrl C processing enable event.

F012

Wait for line processing enable event failed.

F013

Wait for Ctrl C processing enable failed.

F014

Wait for system testing done event failed.

FF0x

Line x test process timeout occurred.

Testing and Troubleshooting 2–59

2.8.3.1 DZ System Test Summary Messages
The DZ system test displays a statistics and error information summary
for each DZ line. Example 2–7 shows a sample DZ summary screen.

********** FST EXT_ERRPT

Line
---0
1
2
3

L_Param
-------

Chr_Xmt
-------00002B50
00002B50
00002B30
00000000

1FFA

0 00:07:26 **********

Chr_Rec
Error
-------- ---------------------00002B50 ***** No Errors *****
00002B50 ***** No Errors *****
00002B29 ?? 1st Char not Rcvd
00000000 *Not Tested - Console*

********** KA60_SYSTST_NXT_SCR ((RTN=Y), (’!’=N))...... ?

Example 2–7

Sample DZ System Test Summary Screen

! The first column lists the line number. Line 0 is the LK201 connector,
line 1 is the mouse connector, line 2 is the modem connector, and line
3 is the printer connector.

" The second column lists the contents of the line parameter register

when an error occurs. This entry is blank if no error occurred in that
line.

# The third column lists the total number of characters transmitted
over the line.

$ The fourth column lists the total number of characters received on the
line.

% The fifth column lists the current line status.

2–60 Testing and Troubleshooting

2.8.4 Memory System Test Error Messages
There are relatively few memory system test error messages. Table 2–27
lists these possible messages.
Table 2–27 Memory Errors Reported by Memory System Test Module
Error Code

Meaning

PPPP.0001

Success, no error detected.

FEFE.0001

Monitor requested an exit.

PPPP.0011

At least one single bit error was detected and corrected.

000M.001F

Memory comparison error occurred.

000L.000F

Fatal error occurred.

SSSS.FFLL

Error from kernel call occurred.

Table Key:
PPPP = number of pages tested in the last pass.
SSSS = kernel’s error code.
LL = failed kernel call location in memory system test.
M = failing module’s mid number.

2.8.4.1 Memory Extended Information Messages
The memory system test offers an extended status screen.
Example 2–8 is a sample display for a system with 16 Mbyte memory
modules in MID 0 and MID 1. The actual extended status displays
depend on the number and type of memory modules in the workstation.

Testing and Troubleshooting 2–61

MID
--0
1
1
1
1
0
1
0

ADDR
-------00000000
01000000
000065B0
00006520
001A11A0
00006530
001A2010
0000652E

Example 2–8
Display

SBE
--4
2
1
1
1
1
1
1

POS
--**
**
0F
1A
03
1A
00
1A

QUAD
---*
*
0
0
1
1
0
1

#PAG
PAG_TST
------ --------008000 00000E77F
008000 00000E77E

Sample Memory System Test Extended Information

! The M-bus base address for the module in MID 0 is 0000000016.
" The module in MID 0 has four single-bit correctable errors (SBE). The
second group of numbers is a log of the error events. The events are
logged in chronological order and identified by the MID of the faulty
module. The event address is a relative address, which when added
to the base address gives the event’s M-bus address. The relative
address helps pinpoint the chip causing the fault.

# Any SBEs have a position code indicating which bit is in error. This
may help uncover a stuck bit on a memory chip.

$ There is also a field showing in which quadword the SBE occurred.
% This field shows the maximum number of pages per module.
& This field shows the number of pages tested per module.

2–62 Testing and Troubleshooting

2.8.5 Network Interface (NI) System Test Error Messages
There are two types of NI error messages, for system tests and kernel
calls.
System Tests
NI error codes for system tests have the following format:
0

Error Code
Test Number

The error code at the right identifies the specific failure.
The test number of the failed test is the digit to the left of the separator.
Table 2–28 lists possible NI system test numbers.
Table 2–29 lists possible NI system test error codes.
Table 2–28 NI System Test Numbers
Test
number

Description

Verify network controller chip interrupt done at initialization.

Test the internal loopback.

Reject a packet with a bad cyclic redundancy check (CRC) or
accept a packet with a good CRC.

Perform multicast filtering and promiscuous receive operation.

Force a collision error.

Force an MISS error.

Test the external loopback.

Testing and Troubleshooting 2–63

Table 2–29 NI System Test Error Codes
Code

Meaning

0001
0002
0004
0006
0008
000A
000C
000E
0010
0012
0014
0016
0018
001A
001C

No error detected.
No packet received.
Packet data miscomparison
Received wrong CRC.
Initialization failed.
Received a packet with bad CRC.
CRC flag was not set when forced.
Illegal multicast packet received.
Rejected a packet when in promiscuous mode.
Rejected a legal multicast packet.
RTRY not set when forced.
BUFF not set when forced.
MISS not set when forced.
Transmission error occurred.
Transmission timeout occurred.

Kernel Call Errors
NI system test error codes for kernel calls have the following format:
x

Kernel Call Number
Failed Kernel Call

The failed kernel call appears in the four digits at the left. This error
code has many possible meanings. Refer to the system test error message
documentation for details.
The two digits at the right of the separator are always FC in kernel call
error codes.
The kernel call number of the failed kernel call appears in the last two
digits at the right. Use Table 2–30 to interpret kernel call numbers at the
right side of the error code.

2–64 Testing and Troubleshooting

Table 2–30 NI Kernel Call Error Codes
Code

Kernel call

FC00
FC02
FC04
FC06
FC08

Create process.
Wait any.
Ker$lock device.
Ker$unlock device.
Signal.

FC10
FC12
FC14
FC16
FC18

Clear event.
Allocate memory.
Free memory.
Create device.
Ker$allocate system_region.

FC20
FC22
FC24
FC26
FC28

Ker$allocate system region.
Create event.
Create event.
Create event.
Create connector.

FC30
FC32
FC34
FC36
FC38

Create name.
Create connector.
Create name.
Allocate memory.
Free memory.

FC40
FC42
FC44
FC46
FC48

Ker$lock device.
Ker$unlock device.
Create message.
Ker$lock device.
Ker$unlock device.

FC50
FC52
FC54
FC56
FC58

Signal.
Ker$lock device.
Ker$unlock device.
Signal.
Signal.

FC60

Signal.

Testing and Troubleshooting 2–65

Table 2–30 (Cont.) NI Kernel Call Error Codes
Code

Kernel call

FC62
FC64
FC66
FC68

Signal.
Signal.
Create message.
Create message.

2.8.5.1 Extended Information Messages
Example 2–9 shows a sample NI extended information display.
PKTS SNT = 000000E4
PKTS RCD = 000000D8
NUM PASS = 00000003
PKTS RCD = PKTS SNT - (4 * NUM PASS),
ERR DTCD:
TEST #

TST 00000007 -- EXT LPBK TST

ERR 0000001A -- XMT ERR

Example 2–9

NI Extended Information Display

The NI system test extended information displays show the total number
of packets sent and received during system test. The numbers do not
equal each other due to the forced errors within the test and are provided
only for statistical purposes.
The extended information summary lists any current error information.
This sample summary shows that a transmission error occurred in the
external loopback test.

2–66 Testing and Troubleshooting

2.8.6 SCSI System Test Error Messages
The system test results list an individual error message for each item on
the SCSI bus, including the host. SCSI error codes in this display have
the following format:
x

Error Code
SCSI Command
Device Status
Device Type
Removable/Fixed Medium
Device ID

Device ID is the ID number of the device’s address on the SCSI bus.
The removable/fixed medium status indicates the type of medium:
1 indicates the medium is removable.
0 indicates the medium is fixed.
Device type shows the device type at that address. Table 2–31 lists
possible devices found on the SCSI bus.
Table 2–31 SCSI Device Type Codes
Code

Device

0
1
2
3
4
5
7
8
E

Direct access device (disk)
Sequential access device (tape)
Printer
Processing device
Reserved
Read-only direct access device
Logical unit not present
Vendor-unique
Host/controller

Testing and Troubleshooting 2–67

Table 2–31 (Cont.) SCSI Device Type Codes
Code

Device

Undefined or unique device

Device status indicates the device’s current condition. Table 2–32 lists
possible device status codes.
Table 2–32 Device Status Codes
0
1
2
3
5
6
7

Device is ready to accept commands.
Device is offline.
Drive is not ready.
Diagnostic error occurred.
Device is the initiator/host.
Unit attention has been posted.
Data on this device is protected.

SCSI is the number of the test or utility command in which the error
occurred. Table 2–33 lists possible SCSI command values.
Table 2–33 SCSI Command Codes
Code

Command

0
01
03
05
07

Test unit ready.
Rewind.
Request sense.
Read block limits.
Reassign block.

08
0A
0B
16
10

Read.
Write.
Track select.
Reserve unit.
Write filemarks.

11
12
13

Space.
Inquiry.
Verify.

2–68 Testing and Troubleshooting

Table 2–33 (Cont.) SCSI Command Codes
Code

Command

14
15

Recover buffered data.
Mode select.

17
19
1A
1B
1C

Release unit.
Erase.
Mode sense.
Start
Receive diagnostic result.

1D
25
FF

Send diagnostic.
Read capacity.
Indicates external loopback test in progress.

NOTE
The preceding command listing does not mean all mentioned
commands are implemented.
Error code indicates the exact error. Table 2–34 lists possible SCSI system
test error codes.
Table 2–34 SCSI System Test Error Codes
Code

Meaning

01
02
03
04
05

No error occurred.
Illegal device type reported.
Error reported after a WST monitor call.
Error reported after an ELN call.
Illegal host ID read from NVR.

06
07
08
09
0A

Media error reported by the device.
Hardware error reported by the device.
Read/write test failed.
Device is not ready.
Data on this device is protected.

0B
0C

Command did not complete succesfully.
Read test failed.

Testing and Troubleshooting 2–69

Table 2–34 (Cont.) SCSI System Test Error Codes
Code

Meaning

0D
0E
0F

External loopback test number 1 failed.
External loopback test number 2 failed.
External loopback test number 3 failed.

10
11
12
13
14

External loopback test number 4 failed.
External loopback test number 5 failed.
External loopback test number 6 failed.
External loopback test number 7 failed.
External loopback test number 8 failed.

15
16
17
18

Block reassignment failed.
Hardware error occurred during reassignment.
Medium error occurred during a send dialog level 2 command.
Hardware error occurred during a send dialog level 2 command.

19
1A
1B
1C
1D

Medium error occurred during a send dialog level 1 command.
Hardware error occurred during a send dialog level 1 command.
System failed to start the device.
System failed to read device’s capacity.
Hardware error occurred during a write operation.

1E
1F
20
21
22

Medium error occurred during a read operation.
Hardware error occurred during a read operation.
Device is not ready.
Hardware error occurred during test unit ready state.
Medium error occurred during test unit ready state.

23
24
25

Bad block found during a read or write operation on the drive.
System is in Manufacturing mode, and the bus is empty.
SCSI bus configuration is illegal. One of the devices on the bus
has the same ID as the host.
Device is hung trying to complete the command.

2–70 Testing and Troubleshooting

2.8.6.1 SCSI System Test Summary Messages
The SCSI summary screen displays a line of information for each slot on
the SCSI bus. Example 2–10 shows a sample SCSI summary display.
----------------- SCSI Summary Screen ----------------ID
DevName
Reads
Writes
BBRs
SndDiag
----- ------------- -------- -------- --------0
RRD40
00022E94 00000000 00000000 00009F98
1
.
.
.
.
.
2
.
.
.
.
.
3
RZ55
00027E60 00004FCC 00000000 00009F98
4
RRD40
000005DA 00000000 00000000 000001AC
5
.
.
.
.
.
6
.
.
.
.
.
7
Host
.
.
.
.
--------------- Extended Sense Packet
-------------Id

6 :

06 00 00 00 00 00

---------------End of SCSI Summary Screen -------------

Example 2–10

Sample SCSI Summary Screen

Table 2–35 explains each column in the SCSI summary display.
Table 2–35 SCSI Summary Screen Entries
Heading

Meaning

ID
DevName
Read
Writes
BBRs
SndDiag

SCSI bus slot ID of the device
Device name from the inquiry data
Number of read operations performed on the device
Number of write operations performed on the device
Total number of bad blocks replaced on this device
Total number of send dialog level 1 and 2 commands performed
on the device.

The extended sense packet message shows the last sense packet received
and that packet’s ID. The following table lists the digits used in the
extended sense packet code.
Byte

Meaning

Sense key portion of the extended sense packet

Testing and Troubleshooting 2–71

Byte

Meaning

2
3
4
5
6
7
8
9
10
11

Information byte (MSB)
Information byte
Information byte
Information byte (LSB)
Additional sense length
Reserved byte
Reserved byte
Reserved byte
Reserved byte
Additional sense code

2.8.7 LEGSS System Test Error Messages
Table 2–36 lists possible graphics system test error messages.
Table 2–36 Graphics System Test Error Codes
Error Code

Meaning

0000.0001

No error detected.

0000.1000

Bus mastership error: GVAX executing in M-bus, and host
executing in M-bus.

0000.1100

Bus mastership error: GVAX executing in M-bus, and host
executing in DRAM.

0000.1200

Bus mastership error: GVAX executing in DRAM, and host
executing in M-bus.

0000.1300

Bus mastership error: GVAX executing in DRAM, and host
executing in DRAM.

0000.2000

GVAX error drawing into bitmap.

0000.2010

GVAX error drawing into bitmap, and pattern buffer was
corrupted.

0000.4000

Host error writing into the bitmap.

0000.8000

Weitek error writing into DRAM.

0000.F000

Initialization error, could not allocate memory or could not
connect to this device.

NOTE
A bus mastership error means that the lock (memory location)
was incorrectly updated by GVAX, the host, or both.

2–72 Testing and Troubleshooting

During the LEGSS test, more than one processor may show an error. In
that case, the appropriate error values from Table 2–36 (.2000, .4000,
.8000) are added together. For example, if both the GVAX and the Weitek
detect an error, the reported error code is 0000.A000.
For errors 0000.2000, 0000.2010, and 0000.4000, more information about
the failure is in the DRAM memory locations described in Tables 2–37
and 2–38. These locations contain valid data only if one of these three
failures occurred.
Table 2–37 GVAX Errors 2000 and 2010
Location

Meaning

3E7FFFD0
3E7FFFD4
3E7FFFD8
3E7FFFDC
3E7FFFE0
3E7FFFE4

Bitmap address of failure
Expected data
Actual data
Pattern buffer address of failure
Expected data
Actual data

Table 2–38 Host Error 4000
Location

Meaning

3E7FFFA8
3E7FFFAC
3E7FFFB0

Bitmap address of failure
Expected data
Actual data

2.8.8 TQK70 System Test Error Messages
TQK70 system test error messages have the following format:
x

Error Code
Status

The four-digit error code on the right specifies the specific error.

Testing and Troubleshooting 2–73

The four-digit status code on the left represents some additional
information about the system’s status. The use of this additional code
depends on the particular TQK70 error code.
Table 2–39 shows the possible TQK70 system test error codes. Where
applicable, the table describes the status word in the left half of the error
code.
Table 2–40 lists response packet error codes, Table 2–41 lists VAXELN
status error codes, and Table 2–42 lists SA error codes used in TQK70
status codes.
Table 2–39 TQK70 System Test Error Codes
Error Code

Meaning

0001

No error occurred.

0002

Get DUST status response packet error.
Status code: See Table 2–40.

0003

The controller is not in an idle state when it should be.

0004

Execute the local program response packet error.
Status code: See Table 2–40.

0005

Send data response packet error.
Status code: See Table 2–40.

0006

Receive data response packet error.
Status code: See Table 2–40.

0007

Received unexpected data in the zeros test.
Status code: shows where the miscomparison occurred (1 to 512).

0008

Received unexpected data from the ones test. Status code: shows
the index where the miscomparison occurred (1 to 512).

0009

Received unexpected data from the counting data test.
Status code: shows the index where the miscomparison occurred
(1 to 512)nnn.

000A

Abort program response packet error.
Status code: See Table 2–40.

000B

Get DUST status response packet error.
Status code: See Table 2–40.

000C

The controller is not idle when it should be.

000D

Execute local program response packet error.
Status code: See Table 2–40.

2–74 Testing and Troubleshooting

Table 2–39 (Cont.) TQK70 System Test Error Codes
Error Code

Meaning

000E

Wait-all kernel call failed.

000F

Get DUST status response packet error.
Status code: See Table 2–40.

0010

Receive data response packet error.
Status code: See Table 2–40.

0012

Receive error, data miscompared.
Status code: represents the number of miscompared bytes.

0013

Data miscomparisons exceed the limit of 100. Status code:
represents the number of miscomparisons.

0014

Abort program response packet error.
Status code: See Table 2–40.

0015

Wait for response command returned bad status.

0016

Invalid command

0017

Command aborted.

0018

Drive unit offline. Status code values:
1

Unit unknown or on a line to another controller.

No volume mounted, or the drive is disabled.

Unit is inoperative.

Unknown subcode specified.

0019

Drive unit available.

001A

Media format error

001B

Unit write-protected. Status code values:
1

Unit is hardware write-protected.

Unit is software write-protected.

A TK50-formatted cartridge is in the TK70 drive.

Unknown subcode specified.

001C

Comparison error.

001D

Data error: long gap data error.

001E

Data error: data sync not found.

Testing and Troubleshooting 2–75

Table 2–39 (Cont.) TQK70 System Test Error Codes
Error Code

Meaning

001F

Data error: write lost data error.

0020

Software data error: software write error.

0022

Software data error: software read error.

0023

Hardware write error.

0024

Hardware read error.

0025

Host buffer access error. Status code values:

0026

0027

Unknown cause to access error.

Nonexistent memory error.

Host memory parity error.

Invalid page table.

Unknown subcode specified.

Controller error. Status code values:
1

Communication channel timeout.

Internal inconsistency.

Unknown subcode specified.

Drive error. Status code values:
1

Drive command timeout.

Controller detected a transmission error.

Recoverable drive fault.

Unrecoverable drive fault.

Unknown subcode specified.

0028

Serious exception.

0029

Unexpected tape mark encountered.

002A

Record data truncated, unrecoverable data error.

002B

Tape position lost.

002C

Message from internal diagnostic.

002D

Power failure.

002E

Formatter error.

2–76 Testing and Troubleshooting

Table 2–39 (Cont.) TQK70 System Test Error Codes
Error Code

Meaning

002F

Invalid major error code returned.

0030

Controller timed out during start and wait state.

0032

Controller reported an error during start and wait state.

0033

Controller timed out in step 1 of the DMA test.

0034

Controller timed out in step 2 of the DMA test.

0035

Controller timed out in step 3 of the DMA test.

0036

Allocation of system memory failed. Status code values:

0037

Allocate failed.

Invalid address.

Invalid context.

Invalid entry.

Invalid priority.

Invalid vector.

Interrupts disabled.

List too short.

No access.

Nondecimal.

Null value.

Overflow.

Timed out.

Truncated data.

Undefined vector.

Unknown status returned.

Error found by step 1 of the controller initialization procedure.
Status code: See Table 2–42.

Testing and Troubleshooting 2–77

Table 2–39 (Cont.) TQK70 System Test Error Codes
Error Code

Meaning

0038

Error in step 1 of the controller initialization procedure. Status
code values:
1

Unit failed to enter initialization step 1.

No support for host interrupt vectors.

Port does not support the enhanced diagnostic test.

Port does not support odd host addressing.

Port does not support address mapping.

No support for 22-bit host bus.

0039

Error found by step 2 of the controller initialization procedure.
Status code: See Table 2–42.

003A

Error occurred in step 2 of the controller initialization procedure.
Status code values:
1

Unit failed to enter initialization step 2.

Incorrect connector type.

Incorrect data during initialization step 2.

Unit unexpectedly entered diagnostic wrap mode.

Incorrect number of command ring descriptors.

Incorrect number of response ring descriptors.

003B

Error found by step 3 of the controller initialization procedure.
Status code: See Table 2–42.

003C

Error in step 3 of the controller initialization procedure. Status
code values:

003D

Unit failed to enter initialization step 3.

Interrupts not disabled.

Incorrect interrupt vector returned.

Error found by step 4 of the controller initialization procedure.
Status code: See Table 2–42.

2–78 Testing and Troubleshooting

Table 2–39 (Cont.) TQK70 System Test Error Codes
Error Code

Meaning

003E

Error in step 4 of the controller initialization procedure. Status
code values:
1

Unit failed to enter initialization step 4.

Incorrect hardware, not TQK70.

003F

CSR does not exist.

0040

Controller timed out during initialization.
Status code: Value is the step (1 to 4) that did not interrupt.

0042

Controller did not interrupt.
Status code: Value is the number of the step that did not
interrupt.

0043

Controller detected an error.
Status code: Shows the step that detected the error.

0044

DMA failed, area not written over by test.

0045

Controller is not a TK50 or TK70 type.

0046

Failed to deallocate IO buffer.
Status code: See Table 2–41.

0047

Failed to deallocate command envelope.
Status code: See Table 2–41.

0048

Command sequence error.

0049

Invalid command end message.

004A

Controller detected internal error.

004B

Controller hung error.

004C

Failed to allocate a new command envelope.

004D

Command sequence error.

004E

Controller timed out by host, no progress made on command.

004F

Data under error, fewer bytes written than requested.

0050

Duplicate drive detected.

0052

Drive operation failed, tape transfer error log received.

0053

Invalid command end message.

0054

Message received from controller with unknown end code.

Testing and Troubleshooting 2–79

Table 2–39 (Cont.) TQK70 System Test Error Codes
Error Code

Meaning

0055

Failed to allocate IO buffer.
Status code: See Table 2–41.

0056

Invalid command.

0057

Command aborted.

0058

Drive unit is offline. Status code values:
1

Unit unknown.

Volume dismounted.

Unit inoperative.

Unknown subcode returned.

0059

Drive unit is available when it should not be.

005A

Media format error.

005B

Drive unit is write protected. Status code values:
1

Unit hardware is write-protected.

Unit software is write-protected.

A TK50-formatted cartridge is in the TK70 drive.

Unknown write-protection subcode returned.

005C

Data comparison error.

005D

Long gap data error. Staus code values:
1

Hardware read error.

Long gap data error.

005E

Data sync not found.

005F

Write data lost.

0060

Unrecoverable read error. Status code values:
1

Error during a write operation.

Error during a read operation.

2–80 Testing and Troubleshooting

Table 2–39 (Cont.) TQK70 System Test Error Codes
Error Code

Meaning

0062

Host buffer access error. Status code values:

0063

0064

Unknown cause to access error.

Nonexistent memory error.

Host memory parity error.

Invalid page table.

Unknown subcode returned.

Controller error. Status code values:
1

Communication channel timeout.

Internal inconsistency.

Unknown subcode returned.

Drive error. Status code values:
1

Drive command timeout.

Controller detected a transmission error.

Recoverable drive fault.

Unrecoverable drive fault.

Unknown subcode returned.

0065

Serious exception error.

0066

Unexpected tape mark encountered.

0067

Record data truncated.

0068

Tape position lost.

0069

Formatter error.

006A

Invalid status code returned in response packet.

006B

A response packet was received from an unknown command.

006C

Drive error byte decoder output.
Status code: See Table 2–41.

Testing and Troubleshooting 2–81

Table 2–40 Response Packet Error Codes
Error Code

Meaning

1
2
3
4
5
6
7
8
9
A
B
C
D

Error in command reference number.
Error in endcode.
Invalid command.
No region available.
No region suitable.
Program not known.
Load failure.
Standalone system.
Unknown or invalid status.
Unknown or invalid status.
Host buffer access error.
Unknown or invalid status.
Error in step bits.

Table 2–41 VAXELN Status Error Codes
Code

Meaning

7C1C
7C3C
7C9C
7CB4
7D2C
7C3C

KER$ BAD MODE
KER$ BAD VALUE
KER$ NO ACCESS
KER$ NO MEMORY
KER$ NO VIRTUAL
KER$ BAD VALUE

Table 2–42 SA Error Codes
Code

Meaning

1
2
3
4
5

Envelope packet read error.
Envelope packet write error.
Controller ROM-RAM parity error.
Controller RAM parity error.
Controller ROM parity error.

6
7

Ring read error.
Ring write error.

2–82 Testing and Troubleshooting

Table 2–42 (Cont.) SA Error Codes
Code

Meaning

8
9
A

Interrupt master error.
Host access timeout error.
Credit limit exceeded error.

B
C
D
E
F

Bus master error.
Diagnostic controller fatal error.
Instruction loop timeout error.
Invalid connection identifier error.
Interrupt write error.

10
11
12
13
14

Controller RAM error.
Initialization sequence error.
High-level protocol incompatibility error.
Purge-poll error.
Mapping register read error.

15
16
17
18
19

Mapping attempt error.
Divide error exception.
Single step interrupt.
Nonmaskable interrupt.
Breakpoint interrupt.

1A
1B
1C
1D
1E

Into detected overflow.
Array bounds exception.
Unused opcode error.
Escape opcode exception.
Reserved error code, unknown event.

1F
20
21
22
23

Into interrupt.
ROM checksum error.
MPU error.
RAM error (odd).
RAM error (even).

24
25
26

MPU timer error.
Miscellaneous register wrap error.
Gap detect circuit error.

Testing and Troubleshooting 2–83

Table 2–42 (Cont.) SA Error Codes
Code

Meaning

27
28

USART wrap error.
USART wrap error, no CRC.

29
2A
2B

USART wrap error, CRC.
Drive cable error.
Unknown SA error code returned.

2.8.9 Q-bus Adapter (DWFQA) System Error Codes
Table 2–43 lists the possible fatal error codes for the DWFQA Q-bus
adapter module.
Table 2–43 DWFQA Q-bus Adapter System Test Error Codes
Code

Test

Error

Meaning

00000914

Fatal
Failure testing M-bus reads to
address/data FIFO. Bad pattern read
back.

00000A14

Fatal: Failure testing FIFO search logic
( low word incorrect ).

00000A24

Fatal: Failure testing FIFO search logic
( high word incorrect ).

00000B14

Fatal: Failure testing valid bit set
recognition.

00000B24

Fatal: Failure testing valid bit clear
recognition.

00000C14

Fatal: Failure testing FQAM interrupts.

2.8.10 CXY08 System Test Error Codes
Loopbacks are required for Customer Services and Manufacturing modes,
but not for customer mode . Table 2–44 lists the possible system test error
codes for the CXY08 module.

2–84 Testing and Troubleshooting

Table 2–44 CXY08 System Test Error Codes
Code

Meaning

0001

Successful pass of CXY08 system test diagnostics.

0002

Controller timed out during initialization.

0003

Controller failed to initialize without diagnostic error.

0004

Insufficient space in FIFO to transmit the character.

0005

Interrupt not seen when expected.

0006

There is an error in the data received, invalid data received.

0007

Received time out during FIFO read.

0008

Controller failed to initialize without diagnostic error.

0009

Received time out during FIFO read.

000A

There is an error in the data received, invalid data received.

000B

Could not force FIFO overrun.

000C

An interrupt timeout has occured, interrupt did not happen in
allowed time.

000D

Invalid received line number during simultaneous DMA test.

000E

There is an error in the data received. Invalid received data
during simultaneous DMA.

000F

Missing characters during simultaneous DMA.

0010

Controller failed to initialize without diagnostic error.

0012

DMA failed to stop on TX.ABORT bit being set.

0013

DMA did not resume after TX.ABORT bit cleared.

0014

There is an error in the data received. Faulty transfer after
resumption from ABORT.

0015

Controller failed to initialize without diagnostic error.

0016

Port failed to interrupt on receipt of BREAK.

0017

Invalid BREAK indicator in FIFO.

0018

Controller failed to initialize without diagnostic error.

0019

Port failed to interrupt on receipt of BREAK.

001A

Faulty transfer during incoming flow-control test.

Testing and Troubleshooting 2–85

Table 2–44 (Cont.) CXY08 System Test Error Codes
Code

Meaning

001B

There is an error in the data received. Faulty transfer during
incoming flow-control test.

001C

Insufficient XOFFs generated during incoming flow-control test.

001D

There is an error in the data received. Faulty transfer during
incoming flow-control test.

001E

There is an error in the data received. XON not generated during
incoming flow-control test.

001F

Controller failed to initialize without diagnostic error.

0020

Insufficient space in FIFO to transmit character.

0022

TX.ENA not set/reset during outgoing flow-control test.

0023

Insufficient space in FIFO to transmit character.

0024

TX.ENA not set/reset during outgoing flow-control test.

0025

Controller failed to initialize without diagnostic error.

0027

An interrupt timeout has occurred.

0028

There is an error in the data received. Faulty transfer during
forced flow-control test.

0029

There is an error in the data received. Faulty transfer during
forced flow-control test.

002A

Insufficient XOFFs generated during forced flow-control test.

002B

There is an error in the data received. Faulty transfer during
forced flow-control test.

002C

There is an error in the data received. XON not generated during
forced flow-control test.

002D

Controller failed to initialize without diagnostic error.

002E

Call to Wait_any return non-success value.

002F

Fatal program error, ELN call failed.

2–86 Testing and Troubleshooting

2.8.11 DSV11 System Test Error Codes
Loopbacks are required for Customer Services and Manufacturing modes,
but not for customer mode. Table 2–45 lists the system test error codes
for the DSV11.
Table 2–45 DSV11 System Test Error Codes
Code

Meaning

0001

Successful pass of system test code.

0002

Modem flag stuck low.

0003

Failed to reset within 10 milliseconds ( skip self-test ).

0004

Command block status data not expected value.

0005

Running flag cleared by DSV11.

0006

ELN reports an error during allocate memory call.

0007

Wait_any call timed out before receiving an interrupt.

0008

Failed to complete command ( no interrupt ).

0009

ELN reports an error during Wait_any call.

000A

Interrupt caused by running flag being cleared.

000B

rsp_available flag not set, command did not complete.

000C

Timed out waiting for response.

000D

Command block status data not expected value.

000E

Unexpected end of command list.

000F

End of command list not seen ( command not completed ).

0010

End of command list found more then once in sequence.

0012

Received data errors detected, DMA failed.

0013

Error writing flag register.

0014

Error reading flag register.

0015

No free command/response block available.

0016

Response list link corrupted.

0017

Internal diagnostic program error, invalid command memory
address.

0018

Error writing low word of command memory data register.

Testing and Troubleshooting 2–87

Table 2–45 (Cont.) DSV11 System Test Error Codes
Code

Meaning

0019

Error writing high word of command memory data register.

001A

Error writing command memory address register.

001B

Internal diagnostic program error, invalid command memory
address.

001C

Error reading low word of command memory data register.

001D

Error reading high word of command memory data register.

001E

Incorrect response sequence.

001F

Unexpected completion status in response.

0020

Internal diagnostic program error, invalid endcount.

0022

Write to CSR caused a machine check
( no access or nonexistent memory ).

0023

ELN reports an error during call to DSL$delay.

2.8.12 TSV05 System Test Error Codes
TSV05 system test codes have the following format:
SSSS.EEEE
EEEE is a specific error code indicating a problem was found while
running the test or with the device.
SSSS displays status information about the device.
Loopbacks are required for Customer Services and Manufacturing modes,
but not for customer mode. Table 2–46 lists the system error codes for the
TSV05 module.
Table 2–46 TSV05 System Test Error Codes
Code

Meaning

EEEE
0001

TSV05 passed the system test.

0002

TSSR reports an error. Errors include SCE, BIE and/or NXM.

2–88 Testing and Troubleshooting

Table 2–46 (Cont.) TSV05 System Test Error Codes
Code

Meaning

EEEE
0003

Need buffer address ( NBA ) bit still set when it should be
cleared.

0004

Initialization reports an failure.

0005

TSV05 failed to interrupt.

0006

Drive unit is offline. There may be a problem with the system.
Otherwise, place drive online and start again.

0007

Data read was not data written
( read forward after skipping tape mark ).

0008

TC1 bit is set (tape status alert). End of tape found during write
command.

0009

Data read was not data written ( read forward ).

000A

Data read was not data written ( read with swap bits enabled ).

000B

Error reported by ELN during WAIT call.

000C

Error writing to device registers.

000D

Error reading device registers.

000E

Error reading flags registers.

000F

SSR and NBA bits not set after an initialization.

0010

SSR bit not set after a initialization.

0012

NBA bit not set after a initialization.

0013

SC, TC2 and TC1 bits are set. Unrecoverable error— tape
position lost.

0014

SC and TC2 bits set. Recoverable error—tape position is one
record beyond what its position was when the function was
begun.

0015

Wait_Any kernel call reported an error.

0016

Error writing to device registers. Nonexistent memory error
reported by the kernel.

0017

Error reading device registers. Nonexistent memory error
reported by the kernel.

0018

Error allocating system memory.

Testing and Troubleshooting 2–89

Table 2–46 (Cont.) TSV05 System Test Error Codes
Code

Meaning

EEEE
0019

SSR bit not set, indicating the command did not complete in
allowed time.

1110

CS mode only: Operator failed to respond to output message
concerning whether a scratch tape is installed in the drive.

2.9 Booting the System After Completing Repairs
After you repair the workstation, boot the system to verify that you
corrected the problem and that the workstation operates correctly. To boot
the workstation, use the BOOT command described in Appendix C.
If the workstation fails to boot, a boot error message appears on the
monitor. Table 2–47 explains possible boot error messages.
Table 2–47 Boot Error Messages
Message

Meaning

BADCHKSUM = 00000808

Bad file header checksum reported.

BADFILEHDR = 00000810

Bad file header exists.

BADFILENAME = 00000818

Bad file name syntax used.

BADIRECTORY = 00000828

Bad directory file format used.

BUFFEROVF = 00000601

Output buffer overflow occurred.

CTRLERR = 00000054

Controller error reported.

DEVASSIGN = 00000848

Device has channels assigned.

DEVINACT = 000020D4

Device is inactive.

DEVOFFLINE = 00000084

Device is not in configuration or
unavailable.

DEVREQERR = 00000334

Device request error occurred.

DRVERR = 0000008C

Fatal drive error occurred.

ENDOFFILE = 00000870

End of file reached.

FILESTRUCT = 000008C0

Unsupported file structure level used.

2–90 Testing and Troubleshooting

Table 2–47 (Cont.) Boot Error Messages
Message

Meaning

FILNOTCNTG = 000002AC

File is not contiguous as required.

INSFMAPREG = 00000344

Map registers are insufficient.

MEDOFL = 000001A4

Medium is offline.

NORMAL = 00000001

Normal, successful completion occurred.

NOROM = 00008018

No ROM is present.

NOSUCHDEV = 00000908

No such device is available.

NOSUCHFILE = 00000910

No such file is available.

NOSUCHNODE = 0000028C

Remote node is unknown.

PARITY = 000001F4

Parity error occurred.

PROTOCOL = 00002074

Network protocol error occured.

SCB2NDINT = 00008010

Unknown interrupt occurred in secondary
boot image.

SCBINT = 00008008

Unknown interrupt occurred in primary
boot image.

TIMEOUT = 0000022C

Device timeout occurred.

WRITLCK = 0000025C

Write lock error occurred.

3
Accessing the Hardware
This chapter contains important safety information, as well as
instructions for
•

Turning off the system unit

•

Removing and replacing covers and assemblies

•

Attaching the shipping brackets for moving the system unit

Be sure to read this chapter before
•

Removing and replacing any field replaceable units (FRUs)
(Chapter 4)

•

Installing options (Chapter 5)

3.1 Using an Antistatic Kit
The Digital antistatic kit (part number 29-26246-00) contains materials
that you should use whenever you handle the static-sensitive components
of the system unit.
CAUTION
Before handling any of the option modules or FRUs, or removing
any static-sensitive materials from an antistatic bag, place the
antistatic wrist strap around your wrist and attach the wrist
strap and the antistatic mat to the metal chassis of the system
unit.
When you remove a module or FRU from its antistatic bag, lay the
module or FRU on the antistatic mat.

3–1

3–2 Accessing the Hardware

3.2 Turning Off the System Unit
You must turn off the system unit before you remove and replace any
FRUs or options. The system unit controls are behind the sliding panel
near the center of the system unit. A three-position lock to the left of the
sliding panel guards access to the controls.
To turn off the system unit:
1. Insert the key into the lock on the front cover, then turn the key
clockwise until it reaches the bottom position.
2. Slide the panel all the way down.
3. Turn the system unit off by setting the on/off switch to the off (0)
position.

Firefox

On/Off Switch
in the Off Position

DEFM020

Accessing the Hardware 3–3

3.3 Removing and Replacing the Front Cover
The front cover fits over the front of the system unit and is removed as
one piece. You must remove the front cover to access any FRU.
To remove the front cover:
1. Pull out the release latch.
2. Grasp the sides of the cover at the bottom and pull up and then out.
Latch

Key

Firefox

B
G

Front Cover
DEFM021

3–4 Accessing the Hardware

To replace the front cover:
1. Place the cover against the front of the system unit, about 5 cm (2
inches) up from the plastic base. Align the metal hooks on the back of
the cover with the corresponding spaces on the system unit frame.
2. Slide the cover down until you feel it lock into place.
3. Push the release latch in.
Figure 3–1 shows the system unit with the front cover removed. All
system modules reside in card cage slots, which are covered by the
graphics, I/O, and Q-bus covers. A mass storage cover fits over the disk
and tape drives in the mass storage area.
Mass Storage Cover

Graphics Cover
I/O Cover

Q-bus Covers
R

DEFM022

Figure 3–1

Inside the System Unit

Accessing the Hardware 3–5

3.4 Removing and Replacing the I/O Cover
The I/O cover fits over slots 4 through 9 in the card cage. A rechargeable
battery is attached to the back side of the I/O cover.
Figure 3–2 shows the I/O cover and connectors.

Status Display

Modem Connector

ThickWire
Ethernet
Connector

ThinWire
Ethernet
Connector

Figure 3–2

Printer Connector

Keyboard/Mouse
Connector

Ethernet Switch

DEFM008

The I/O Cover and Connectors

You must remove the I/O cover to access the following modules:
•

CPU module

•

Memory module

•

I/O module

•

Tape adapter module

•

Q-bus adapter module

If a failure occurs within the I/O cover itself, remove and replace the
cover.

3–6 Accessing the Hardware

You do not need to disconnect the I/O cable from the I/O module to access
or remove a module. Do not disconnect the I/O cable, unless necessary.
Disconnecting the I/O cable effectively removes battery power, so the
nonvolatile RAM (NVR) in the I/O module loses power and its memory
contents. This RAM stores the workstation’s default settings. If you
remove the I/O cable, you must reset the default values when you turn
the workstation on again.
To remove the I/O cover:
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Disconnect all external connectors on the I/O cover. You may want to
label them, to help you remember where they go.
4. Release the four ¼-turn captive screws that hold the I/O cover in
place.
5. Gently pull the I/O cover away from the card cage about two inches.

1/4-Turn
Captive Screw

I/O Cover

DEFM024

Accessing the Hardware 3–7

6. If you need to disconnect the ribbon cable that connects to the I/O
module, disconnect it at the I/O module (not at the I/O cover).
Ribbon Cable

Cable Ejector
I/O Module Connector
Cable Ejector

I/O Cover

DEFM025

7. Lift the I/O assembly away from the card cage and carefully set the
assembly aside.
To replace the I/O cover, reverse the preceding steps.

3.5 Removing and Replacing the Graphics Cover
The graphics cover fits over the graphics frontplane and the two or three
graphics modules in slots 1, 2, and 3.
You must remove the graphics cover to access the graphics frontplane and
the graphics base, graphics output, and graphics expansion modules.
To remove the graphics cover:
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).

3–8 Accessing the Hardware

3. Find the graphics cover on the right side of the card cage. Note the
location of the three RGB cables. They are labeled and stamped with
red, green, and blue color bands.
•

If you are replacing the graphics frontplane, disconnect the RGB
cables from the graphics cover.

•

If you are just removing the cover to look at the green LED display
on the graphics base module, leave the RGB cables connected.

4. Release the two ¼-turn captive screws that hold the graphics cover in
place.
Graphics
Frontplane

1/4-Turn
Captive Screw

Graphics Cover

DEFM026

5. Gently pull the cover away from the card cage, bottom first.
To replace the graphics cover, reverse the preceding steps.

Accessing the Hardware 3–9

3.6 Removing and Replacing the Graphics
Frontplane
The graphics frontplane connects the two or three graphics modules
installed in slots 1 through 3 of the card cage. The frontplane also
provides video output connections to the color monitor.
You must remove the graphics frontplane to access graphics modules in
slots 1, 2, or 3.
To remove the graphics frontplane:
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the graphics cover (Section 3.5).
4. Loosen the three large captive thumbscrews on the graphics
frontplane.
5. Grasp the top and bottom of the graphics frontplane. Remove the
frontplane by gently rocking it back and forth, while pulling it away
from the graphics module connectors. Be careful not to bend any pins
on the connectors.
To replace the graphics frontplane:
1. Align the three long prongs that extend from the back of the graphics
frontplane with the corresponding holes on the module connectors.
The three connectors on the graphics frontplane correspond to the
mating connectors on the graphics modules.
2. Push the graphics frontplane connectors onto the graphics module’s
mating connectors, using an even force to avoid bending connector
pins. If necessary, rock the module back and forth slightly.
3. Tighten each of the three thumbscrews slightly. Then tighten each
one a bit more, until all are sufficiently tightened.
4. Replace the graphics cover and tighten the two captive screws.
5. Replace the RGB connectors by connecting each RGB connector to its
corresponding color.
6. Run the red, green and blue color check tests to verify that the
connections are secure. See Chapter 2 for detailed information on
how to run these tests.

3–10 Accessing the Hardware

3.7 Removing the SCSI Terminator From the
System Unit
The SCSI terminator covers the SCSI connector at the upper-left corner of
the system unit.
You must remove the SCSI terminator before you can remove the control
panel or install an RRD40 optical compact disc drive (Chapter 5).
To remove the SCSI terminator:
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Pull apart the clamps holding the SCSI terminator to the SCSI
connector.
4. Pull the SCSI terminator away from the connector, as shown.
NOTE
Remember to reconnect the SCSI terminator. If you install an
optical compact disc drive, place the terminator on the drive
(Chapter 5).

Accessing the Hardware 3–11

SCSI
Terminator

DEFM027

3–12 Accessing the Hardware

3.8 Removing and Replacing the Mass Storage
Cover
The mass storage cover fits over the mass storage area at the top of the
system unit. You must remove the mass storage cover in order to remove
a disk drive, a tape drive, the control panel.
To remove the mass storage cover:
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Release the five captive screws that hold the mass storage cover in
place.

Mass Storage
Captive Screws (5)
DEFM028

4. Pull the cover away from the mass storage area.
To replace the mass storage cover, reverse the preceding steps.

Accessing the Hardware

3–13

3.9 Securing the Shipping Brackets for Moving the
Workstation
If you are moving the workstation a short distance, follow the
instructions in Chapter 7 of the VAXstation 3520/3540 Operator’s
Guide or the VAXstation 3820/3840 Owner’s Manual for dismantling
the workstation.
If you are moving the workstation to another building or farther,
you must secure the shipping brackets to protect the drives during the
move.
To secure the shipping brackets to the system unit:
1. Perform all dismantling steps as instructed in the VAXstation
3520/3540 Operator’s Guide or the VAXstation 3820/3840 Owner’s
Manual.
2. Remove the mass storage cover (Section 3.8).
3. Find the metal shipping brackets on each side of the mass storage
area. Each side has a top bracket with an arm and a bottom bracket
with an arm. You may need to use a flashlight to see the brackets.
4. Lift up on the top bracket—the left and right arms move as a unit.
Hold the bracket against the top of the mass storage area, as you turn
the orange screws to the right to tighten them. The mounting bracket
arms should be held between the system unit frame and the shaft of
the orange screws.
5. Push down on the bottom bracket. Hold the bracket against the
bottom of the mass storage area, as you turn the orange screws to the
right to tighten them. You may need to push hard to hold the bracket
against the bottom of the mass storage area; use a screwdriver or
other tool if necessary. The mounting bracket arms should be held
between the system unit frame and the shaft of the orange screws.
6. Replace the mass storage cover.
To release the shipping brackets when unpacking the workstation, turn
the four orange screws to the left until you hear a snapping sound as the
brackets release.

3–14 Accessing the Hardware

3.10 Removing and Replacing the Back Cover
The back cover consists of the four panels that make up the sides, top,
and back of the metal chassis. You remove this cover as one piece.
You must remove the back cover to access the backplane.
To remove the back cover:
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the 10 screws that hold the back cover on.

B
G

DEFM029

Accessing the Hardware

3–15

4. Slide the back cover away from you as far as it will go (about 5 cm, or
2 inches), to release the four fasteners that hold the cover to the top
of the mass storage area.
5. Remove the cover by lifting it straight up and then away from the
system unit.
To replace the back cover, reverse the preceding steps.

4
Removing and Replacing FRUs
This chapter describes how to remove and replace field replaceable
units (FRUs) in the VAXstation 3520/3540 and VAXstation 3820/3840
workstations, including the following:
•

Battery pack

•

System modules

•

Storage devices, such as tape and disk drives

•

Power supplies

•

Electrical and mechanical parts and assemblies

•

Peripheral devices, such as the keyboard, mouse, and tablet

See Appendix B for a list of FRUs and their part numbers.

4.1 Before You Begin
It is the customer’s responsibility to back up software before a Digital
service representative arrives at the customer’s site. This step is
important to ensure that data is not lost during any service process.
The customer should also shut down the worksystem software. Before you
perform any maintenance work, confirm that the customer has completed
both of these tasks.
CAUTION
Before handling any of the option modules or FRUs or removing
any static-sensitive materials from an antistatic bag, place the
antistatic wrist strap around your wrist and attach the wrist
strap and the antistatic mat to the metal chassis of the system
unit. When you remove a module or FRU from its antistatic bag,
lay the module or FRU on the antistatic mat.

4–1

4–2 Removing and Replacing FRUs

4.2 Removing and Replacing Internal FRUs
This section describes procedures for removing and replacing FRUs in
the workstation. Before attempting any of these procedures, you must
perform the following steps, as described in Chapter 3:
1. Turn off the workstation.
NOTE
In power-associated operations, you will also be instructed to
unplug the system unit power cord from the power source.
2. Remove the front or back cover from the system unit.
3. Remove the cover that encloses the FRU you are replacing.

4.2.1 Inspecting the EOS and FCC Clips
To comply with FCC regulations, blank covers and the front covers of the
system unit have transient-protection EOS and FCC clips. Before you
install an FRU or cover, check that the FCC and EOS clips are in good
condition.
Following proper antistatic procedures, inspect the FCC and EOS clips for
residue or corrosion. If the clips are dirty, clean them using a cotton swab
dampened with alcohol.
Check that the FCC clips are in an arched shape. If you push on them
slightly, they should bend and then return to their original shape.

4.2.2 Battery Pack
A rechargeable battery pack is mounted on the inside of the I/O cover.
The battery pack maintains the contents of the nonvolatile RAM (NVR)
when the power to the workstation is turned off. Replace the rechargeable
battery if the system prompts you for a language choice after you turn the
power to the workstation on again.
To replace the battery pack (observing antistatic procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the I/O cover (Section 3.4).

Removing and Replacing FRUs 4–3

4. Disconnect the battery cable from the I/O cover, as shown. Remove
the battery from its holder by spreading the sides of the battery holder
and lifting the battery out.

Battery Pack Cable
Battery Pack

Battery Pack Connector

Battery Pack Holder
DEFM030

5. Place a new battery in the battery holder and reconnect the battery
cable.
6. Replace all covers and turn on the workstation.
7. Reenter system default settings if necessary, using console commands
(Appendix C).
NOTE
After you enter system default settings, keep the workstation
running for several hours while the newly installed battery
charges. Otherwise, the NVR contents will be lost again.

4–4 Removing and Replacing FRUs

4.2.3 System Modules
This section describes how to remove and replace system modules in the
M-bus and graphics bus slots (1 through 9) behind the I/O and graphics
covers. Use the configuration display to see which modules are in each
slot. Type T 50 and press Return . The monitor displays a list that relates
module IDs to physical slots.
See Section 2.2.2 for more details about the T 50 configuration display.
Note that card cage slots 10 through 12 are reserved for Q-bus modules.
Figure 4–1 show the system unit backplane configuration.

Q-bus Covers

I/O Cover

Graphics Expansion
Module (Optional)

Graphics Output Module

Graphics Base Module

I/O Module

Memory Module (Optional)

CPU Module or Memory
Module (OPtional)

CPU Module

Memory Module

Q-bus Adapter Module (Optional)or
Tape Adapter Module (optional)

TQK70 Module (Optional)

Slot
Numbers

Reserved

Slots

Reserved

Module ID (Mid) Numbers

Graphics
Cover
MA-X0689-89

Figure 4–1

The System Unit Backplane Configuration

You remove and replace all M-bus and graphics bus modules in the same
manner.
NOTE
When you remove modules, be sure to use proper antistatic
procedures. Leave the system unit power cord plugged in, to
provide a ground for the antistatic mat and wrist strap.

Removing and Replacing FRUs 4–5

To remove an M-bus or a graphics bus module (observing antistatic
procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Disconnect cables as needed.
NOTE
If you disconnect the ribbon cable between the I/O module and
I/O cover, you will have to reset the NVR default values when
you turn the workstation on again.
4. If you are replacing the I/O module, take the Ethernet address chip
from the old I/O module and put it onto the new I/O module. This step
is necessary to retain the same Ethernet address. Be sure to insert
the chip in the same direction on the new I/O module.

LED
Ethernet
Address Chip

Lance Chip
SIA Chip

DEFM078

Figure 4–2

Ethernet Address Chip on the I/O Module

5. Remove the appropriate cover as needed.
6. Pull out on the module’s top and bottom release levers, as shown.

4–6 Removing and Replacing FRUs

7. Gently pull the module out of the card cage.

DEFM032

To replace an M-bus or graphics bus module:
1. Slide the module into the appropriate slot, making sure the module
fits firmly into the backplane connectors.
2. Press the top and bottom release levers simultaneously. You must
press these levers simultaneously for them to seat properly.
3. Replace the appropriate covers.

Removing and Replacing FRUs 4–7

4.2.4 Control Panel Module
You must remove the mass storage cover to access the control panel
assembly. The control panel assembly consists of the control panel cover
and the control panel module.
To remove the control panel assembly (observing antistatic
procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the mass storage cover and the SCSI terminator (Section 3.8).
4. Remove the two screws that hold the control panel assembly in place
and pull the assembly away from the mass storage area.

Control Panel
Assembly Screws

Mass Storage
Cover Screws (5)
DEFM034

5. Holding the control panel assembly in one hand, disconnect the SCSI
cable.
6. Place the control panel assembly on top of the system unit. Allowing
it to dangle may damage the wiring.

4–8 Removing and Replacing FRUs

To remove the control panel module from the control panel
assembly:
1. Disconnect the ribbon cable from the control panel module by
releasing the two plastic latches.
NOTE
If you need to replace a defective control panel, remove the
ribbon cable.
2. Unscrew the four screws that secure the control panel module to the
control panel cover and lift the module away from the control panel.
Ribbon Cable

Control Panel
SCSI
Connector
Area

DEFM035

To replace the control panel assembly:
1. Screw in the four screws that hold the control panel module to the
control panel.
2. Reconnect the ribbon cable to the control panel cover.
3. Place the three control panel tabs into chassis slots. Tighten the two
captive screws.
4. Replace the mass storage cover and the SCSI terminator.
5. Replace the front cover.

Removing and Replacing FRUs 4–9

4.2.5 Q-bus Options
Q-bus option modules are installed in slots 10, 11, and 12.
NOTE
When you remove modules, be sure to use proper antistatic
procedures. Leave the system unit power cord plugged in to
ground the antistatic mat and wrist strap.
To remove a Q-bus module (observing antistatic procedures):
1. To find the location of a Q-bus option in the system, type T 50 0 and
note the order of the option in the backplane. The Q-bus adapter
option installs in slot 9. The first Q-bus option installs in slot 10, the
second in slot 11, and the third in slot 12.
2. Turn off the workstation.
3. Remove the front cover from the system unit (Section 3.3).
4. Disconnect any external cables.
5. Remove any blank covers covering the Q-bus slot. If there are no
covers, remove the screws on the module handle.
6. Remove the module from the the Q-bus slot.
7. Remove any internal cables.
To replace a Q-bus module, reverse the preceding steps. The next
figure shows a TQK70 module being installed in slot 10.

4–10 Removing and Replacing FRUs

Slot 10

TK70 Tape Drive
Controller Module

DEFM054

Removing and Replacing FRUs 4–11

4.2.6 TK70 Series Tape Drive
The TK70 series tape drive has a formatted capacity of 296 Mbytes. The
workstation can have one TK70 tape drive installed in the rightmost drive
slot of the mass storage area, behind the mass storage cover.
To remove a TK70 tape drive (observing antistatic procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the mass storage cover (Section 3.8).
4. Remove the control panel (Section 4.2.4).
5. Release the tape drive from its runners by loosening the captive
screws above and below the drive.

Captive Screws

TK70 Tape Drive

DEFM039

6. Slide the tape drive out and hold it close to the tape drive slot until
the signal and power cables at the back of the drive are accessible.

4–12 Removing and Replacing FRUs

7. Disconnect the power cable from the back of the tape drive.

Signal Cable

Power Cable

DEFM038

8. Note the orientation of the signal cable before disconnecting it from
the back of the tape drive.
9. Slide the tape drive the rest of the way out of the tape drive slot.
10. If you are installing a new drive, transfer the drive mounting brackets
from the old tape drive to the new one.
To replace a TK70 tape drive, reverse steps 1 through 9.
If you feel resistance when sliding the drive into the mass storage area,
pull the drive out and move the cables at the back of the drive out of the
way.
After you have replaced the drive and turned the workstation on, run
diagnostic tests to test the drive.

Removing and Replacing FRUs 4–13

4.2.7 TS05 Tape Drive
The TS05 tape drive has a capacity of 40.5 Mbytes of backup data storage.
You install the TS05 in the top 26.3 cm (10.5 in) mass storage shelf of the
H9642 cabinet.
To remove a TS05 tape drive from the H9642 cabinet, see the service
documentation for the H9642 cabinet.
To remove the TSV05 tape drive controller from the backplane, see
Section 4.2.5.

4.2.8 RZ55 Hard Disk Drive
The RZ55 series hard disk drive has a formatted capacity of 332 Mbytes.
Up to four RZ55 drives can fit behind the mass storage cover. They are
always installed from right to left in the drive slots.
NOTE
If the workstation does not have a tape drive, the first RZ55
must be installed in the tape drive slot at the far right of the
mass storage area, facing the front of the system unit. The drives
are mounted on slide supports to protect them from mechanical
shock. Chapter 5 describes how to install the RZ55 option.
To remove an RZ55 drive (observing antistatic procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the mass storage cover (Section 3.8).
4. Remove the control panel (Section 4.2.4).
5. Disconnect the SCSI connector and the power connector from the disk
drive.

4–14 Removing and Replacing FRUs

SCSI Connector

Power Connector

DEFM036

6. Release the disk drive from its runners by loosening the captive
screws above and below the disk drive, as shown.

Drive ID
Jumpers

Captive Screws

DEFM037

Removing and Replacing FRUs 4–15

7. Carefully slide the disk drive out of the mass storage area.
8. To remove and replace the main device board on the drive, see the
RZ55 Service Manual.
9. If you are installing a new drive, be sure to transfer the drive
mounting brackets from the old RZ55 drive to the new one. See
Section 5.12.2.
10. Set the drive ID on the new RZ55 disk drive to the same drive jumper
as was on the old RZ55 disk drive you just removed. Refer to the
previous figure and Table 4–1 for assistance.
To replace the RZ55 disk drive, reverse the preceding steps.
After you have replaced the drive and turned the workstation on, run
diagnostic tests to test the drive.
Table 4–1 RZ55 Disk Drive SCSI ID Settings
Jumper Settings
Drive ID

Out

4–16 Removing and Replacing FRUs

4.2.9 RZ56 Hard Disk Drive
The RZ56 hard disk drive has a formatted capacity of 665 Mbytes. Up to
four RZ56 drives can fit behind the mass storage cover. They are always
installed from right to left in the drive slots.
NOTE
If the workstation does not have tape drive, the first RZ56 must
be installed in the tape drive slot at the far right of the mass
storage area, facing the front of the system unit. The drives
are mounted on slide supports to protect them from mechanical
shock. Chapter 5 describes how to install the RZ56 option.
To remove an RZ56 drive (observing antistatic procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the mass storage cover (Section 3.8).
4. Remove the control panel (Section 4.2.4).
5. Disconnect the SCSI connector and the power connector from the disk
drive.

SCSI Connector

Power Connector

DEFM036

Removing and Replacing FRUs 4–17

6. Release the disk drive from its runners by loosening the captive
screws above and below the disk drive, as shown.

Drive ID
Jumpers

Captive Screws

DEFM037

7. Carefully slide the disk drive out of the mass storage area.
8. If you are installing a new drive, be sure to transfer the drivemounting brackets from the old RZ56 drive to the new one.
9. Set the drive ID on the new RZ56 disk drive to the same drive jumper
as was on the old RZ56 disk drive you just removed. Refer to the
previous figure and Table 4–2 for assistance.
To replace the RZ56 disk drive, reverse the preceding steps.
After you have replaced the drive and turned the workstation on, run
diagnostic tests to test the drive.
Table 4–2 RZ56 Disk Drive SCSI ID Settings
Jumper Settings
Drive ID

0
1
2
3
4
5
6
7

Out
In
Out
In
Out
In
Out
In

Out
Out
In
In
Out
Out
In
In

Out
Out
Out
Out
In
In
In
In

4–18 Removing and Replacing FRUs

4.2.9.1 Drive Electronics Module
To remove the RZ56 disk drive electronics module (observing
antistatic procedures):
1. Carefully apply outward pressure to the center of the bezel with your
thumb and fingers until the two bezel locking pins clear the holes in
the frame.
NOTE
The top center of the bezel must flex approximately 1/8-inch
outward to clear the pins.
LED Flex Cable
Connector

Locking Pins

Frame Slots

Bezel Clips

LE
DU X
MO -X
E XX
IV XX
D R9 - X
2
E
AM
FR X
H -X
IT XX
(W X
A -XX
HD 29

MA-X1003-89

2. While the bezel is clear of the locking pins, slide it upward until
movement stops (about 3/8-inch). Then remove the bezel from the
drive.

Removing and Replacing FRUs 4–19

3. Remove the three screws shown.
Spindle
motor
connector
A
J5

RZ56
Electronics
board

Insulator

Preamplifier
cable
connector
MA-X0923-89

4–20 Removing and Replacing FRUs

4. Unplug the spindle motor connector at J5.
5. Unplug the preamplifier cable connector at the auxiliary board. When
you set the drive on the work surface, place a support under the drive
to protect the loose preamplifier cable and connector.
6. Lift the drive module and the auxiliary board up and out of the drive.
7. Remove the screw and speednut holding the drive module.
8. Unplug the auxiliary board from J9 on the drive module.
To replace the RZ56 drive electronics module, reverse the preceding
steps.
Check the new module to be sure the jumpers are set to the same position
as on the old module you just removed.

4.2.10 Power Supplies
The system unit has two power supplies, one on either side of the card
cage. Both are connected directly to the backplane.
Remove a power supply if it is faulty or if you are replacing the ac switch
or backplane assembly. You remove both power supplies in the same
manner.
To remove a power supply:
1. Turn off the workstation and unplug the system unit power cord from
the power source.
2. Remove the front cover from the system unit (Section 3.3).
3. Unplug the system unit power cord from the ac filter.
4. Loosen the screw on each pedestal cam and rotate the cams off the
screws. Lift out each cam to remove it, as shown.

DEFM040

Removing and Replacing FRUs 4–21

5. Release the five captive screws that fasten the metal grille to the
chassis under the front of the card cage. Then remove the grille by
rocking it away from the bottom of the chassis, as shown.

Power
Supply 1
Power
Supply 2
R

Grill
DEFM041

4–22 Removing and Replacing FRUs

6. Remove the screw at the top of the power supply that holds the cover
for the mass storage power cable.

Power Supply
Cable Cover
Mass Storage
Power Cable
Connector

DEFM042

7. Remove the power cable cover.
8. Disconnect the mass storage power cable from the power supply and
slide the adjacent rubber grommet off the metal chassis.
9. Loosen the two captive screws that hold the top and bottom of the
power supply in place.
10. To avoid damage to the backplane connector, remove the power supply
by pulling it straight out, as shown.

Removing and Replacing FRUs 4–23

Power Supply

DEFM043

To replace a power supply:
1. Be sure the top and bottom edges of the power supply are mounted in
the plastic guides in the card cage.
2. Slide the power supply all the way in, then push hard until it clicks
into place.
3. Tighten the two captive screws on the power supply.
4. Slide the grommet back into place and reconnect the mass storage
power cable.
5. Replace the power cable cover, making sure the lip on the bottom edge
catches inside the opening and the notched tab at the top fits into the
groove on the grommet.
6. Replace the grille, making sure the lip at the bottom of the grille fits
between the two metal sheets at the bottom of the chassis.
7. Replace the cams snugly against the grille.
8. Plug the system unit power cord into the ac filter, then into the power
source.

4–24 Removing and Replacing FRUs

9. Turn on the workstation. The LED on each power supply should turn
on. If they do not, repeat the replacement procedure, making sure
that the power supply is firmly seated.

4.2.11 AC Filter
The ac filter is under the left power supply, behind the grille.
To remove the ac filter:
1. Turn off the workstation and unplug the system unit power cord from
the power source.
2. Remove the front cover from the system unit (Section 3.3).
3. Unplug the system unit power cord from the ac filter.
4. Loosen the screw on each pedestal cam and rotate the cams off the
screws. Lift out each cam and remove it, as shown in Section 4.2.10.
5. Release the five captive screws that fasten the metal grille to the
chassis under the front of the card cage. Remove the grille by rocking
it away from the bottom of the chassis, as shown in Section 4.2.10.
6. Remove the left power supply.
7. Find the ac input cable that runs across the front of the fan area.
8. Disconnect the ac input cable from the ac filter connector by pulling
the mate-and-lock connector on the cable.

DEFM044

Removing and Replacing FRUs 4–25

9. Remove the three screws that hold the ac filter to the card cage.

DEFM045

10. Tilt the ac filter away from you as you remove it, so it does not catch
on a rivet.
To replace the ac filter, reverse the preceding steps.

4.2.12 AC Switch Assembly
The ac switch assembly includes the ac on/off switch and an input cable.
This assembly is at the right side of the system unit, under the mass
storage area.
NOTE
When you order an ac switch assembly, be sure to order a switch
frame to install behind the on/off switch.
To remove the ac switch assembly:
1. Turn off the workstation and unplug the system unit power cord from
the power source.
2. Remove the front cover from the system unit (Section 3.3).
3. Unplug the system unit power cord from the ac filter.

4–26 Removing and Replacing FRUs

4. Loosen the screw on each pedestal cam and rotate the cams off the
screws. Lift out each cam and remove it, as shown in Section 4.2.10.
5. Release the five captive screws that fasten the metal grille to the
chassis under the front of the card cage. Remove the grille by rocking
it away from the bottom of the chassis, as shown in Section 4.2.10.
6. Remove the right power supply from the enclosure.
7. Disconnect the ac input cable that runs across the front of the fan
area from the ac filter connector by pulling the mating connector on
the cable.
8. Remove the ac input cable from the clip under the card cage.
9. Remove the three screws from the front of the ac switch.
10. Loosen the three nuts that hold the ac switch assembly to the inside
of the right panel on the bottom enclosure.

DEFM046

11. Grasp the ac switch assembly and pull it out of the enclosure.

Removing and Replacing FRUs 4–27

DEFM047

To replace the ac switch assembly, reverse the preceding steps and
install a new switch frame around the on/off switch.

4.2.13 Fans
The two fans are attached to a metal plate bolted to the bottom of the card
cage. Power to the fans is supplied through a Y cable from the backplane.
You can remove and replace fans individually after you remove the metal
plate from the bottom enclosure.
To remove the fans:
1. Turn off the workstation and unplug the system unit power cord from
the power source.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the cams as shown in Section 4.2.10.
4. Remove the metal grille from the front of the bottom enclosure, as
shown in Section 4.2.10.
5. Remove the left power supply (Section 4.2.10).

4–28 Removing and Replacing FRUs

6. Remove the ac filter (Section 4.2.11).
7. Disconnect the Y cable from both fans, as shown.

DEFM048

8. Holding the fan’s metal plate so it will not fall, remove the two screws
that hold the plate to the bottom enclosure.
9. Remove the metal plate with the fans attached.
DEFM049

10. Remove the four screws that hold each fan to the metal plate, then
remove the fans.
To replace the fans:
1. Reverse steps 4 through 9 for removing the fans.
2. Plug the system unit power cord into the power source and turn on
the workstation.

Removing and Replacing FRUs 4–29

3. Verify that both fans are pulling air into the bottom enclosure by
holding your hand 5 cm (2 inches) away from each fan.
4. Turn off the workstation and unplug the system unit power cord from
the power source.
5. Replace the metal grille.
6. Replace the cams.
7. Replace the front cover.

4.2.14 Backplane
The backplane provides all signal and power interconnections for the
system modules. The backplane is connected to a metal plate. The plate
is attached to the back of the bottom enclosure, inside the back cover of
the system unit. You can reach the backplane when the back cover is
removed. You need two people to remove the backplane.
To remove the backplane:
1. Turn off the workstation and unplug the system unit power cord from
the power source.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the back cover from the system unit (Section 3.10).
4. Remove both power supplies (Section 4.2.10).
5. Remove the graphics cover (Section 3.5).
6. Remove the graphics frontplane (Section 3.6).
7. Remove the I/O cover (Section 3.4).
8. Remove any Q-bus module blank covers on slots 10 through 12.
9. Release all M-bus, Q-bus, and graphics bus modules from the
backplane. You do not have to remove the modules from the card
cage so long as you release them from the backplane.
10. Working at the front right side of the bottom enclosure, disconnect the
10-pin DCOK ribbon cable and the fan power cable from the right side
of the backplane.
CAUTION
To avoid damaging the backplane as it is removed, two people
are needed to perform the remainder of this procedure.

4–30 Removing and Replacing FRUs

DCOK Cable

Fan Power Cable

DEFM050

11. Working at the back of the bottom enclosure, remove the eight screws
that secure the metal plate to the back of the enclosure.
Remove the lower screws first and the upper-right screw last. Another
person should support the metal backing plate as the last screw
is removed. Otherwise, the weight of the backplane will cause the
assembly to drop when the last screw is removed, possibly damaging
the backplane connectors.

Removing and Replacing FRUs 4–31

Backplane

DEFM051

12. Slide the metal plate to the right, to release it from the two tabs on
the left side of the enclosure. The backplane and metal plate make up
a single FRU. Do not remove the plate from the backplane.
To replace a backplane:
1. Align the backplane with the back of the bottom enclosure.
2. Slide the two tabs on the side of the backplane onto the flanges on the
sheet metal that makes up the left side of the enclosure.
3. Insert the eight screws that fasten the metal plate to the back of the
enclosure and tighten them partially (enough to provide clearance for
the modules).
4. Insert one module into backplane slot 3 and one into backplane slot 9.
This step aligns the backplane with the card cage guides.
5. Tighten the eight screws the rest of the way.
6. Reverse steps 1 through 9 of the removal procedure.

4–32 Removing and Replacing FRUs

4.3 Removing and Replacing External FRUs
The VAXstation 3520/3540 Hardware Installation Guide and the
VAXstation 3820/3840 Hardware Installation Guide provide detailed
instructions for removing and installing external FRUs. Those
installation instructions are summarized here. For instructions on
removing and installing the RRD40 optical compact disc drive, see
Chapter 5 of this guide.

4.3.1 The Monitor
The VR295 monitor attaches to the video cable assembly, which is
connected to the front of the system unit.
To remove the monitor:
1. Turn off the monitor.
2. Disconnect the keyboard-mouse connector and RGB signal cables from
the front of the system unit.
3. Remove the back cover from the monitor.
4. Disconnect the video cable assembly RGB signal cables from the back
of the monitor.
5. Detach the video cable assembly connector block from the back of the
monitor.
To replace the monitor, reverse the preceding steps.

4.3.2 Keyboard
The LK201 keyboard attaches to the video cable assembly connector block,
which is mounted on the back of the monitor.
To remove the keyboard:
1. Turn off the workstation.
2. Unplug the keyboard cable from the video cable assembly connector
block on the back of the monitor.
To replace the keyboard, reverse the preceding steps.

Removing and Replacing FRUs 4–33

4.3.3 Mouse or Tablet
The mouse or tablet attaches to the video cable assembly connector block,
which is mounted on the back of the VR295 monitor. Only one pointing
device can be connected at a time.
To remove the mouse or tablet:
1. Turn off the workstation.
2. Unplug the mouse or tablet cable from the video cable assembly
connector block on the back of the monitor.
To replace the mouse or tablet, reverse the preceding steps.

5
Installing Options
This chapter describes how to inspect and install options for the
VAXstation 3520/3540 and VAXstation 3820/3840 workstations. These
options include the following:
•

Expansion modules: memory, CPU, and graphics

•

Q-bus adapter module

•

Tape adapter module

•

Q-bus options: CXY08, DSV11, TSV05, TQK70

•

Mass storage options: tape drives, hard disk drive, and optical
compact disc drive

There are two ways to order options:
•

Factory-installed, as part of the original shipment

•

As upgrades (option kits)

This chapter tells you how to install upgrade kits, which consist of the
option itself plus any covers or cables needed to complete the installation.

5.1 Before You Begin
It is the customer’s responsibility to back up software before a Digital
service representative arrives at the customer’s site. This step is
important to ensure that data is not lost during any service process.
The customer should also shut down the worksystem software. Before you
begin installing options, confirm that the customer has completed both of
these tasks.

5–1

5–2 Installing Options

CAUTION
Before handling any of the option modules or FRUs or removing
any static-sensitive materials from an antistatic bag, place the
antistatic wrist strap around your wrist and attach the wrist
strap and the antistatic mat to the metal chassis of the system
unit. When you remove a module or FRU from its antistatic bag,
lay the module or FRU on the antistatic mat.

5.2 Unpacking and Inspecting an Option Kit
When you inspect an option kit, look for external damage to the shipping
container, such as dents, holes, or crushed corners. If any damage is
apparent, write a note describing the damage on the packing slip before
proceeding.
Following antistatic procedures, carefully open the shipping container and
remove the contents. Save the container and packing materials in case
you need to ship the kit in the future.
Remove the option from its antistatic bag or packing materials and
inspect it for shipping damage. Lay it on the antistatic mat. Remove
the remaining kit parts from the container and check them against the
option kit listing to make sure nothing is missing. If any part is damaged
or missing, notify the customer before proceeding.

5.3 Testing the Present Configuration
Before you install any option, you should test the existing workstation to
verify that it is running properly.
To test the workstation, open the sliding panel on the right front of the
system unit and press the Restart/Run button on the control panel. This
initiates the power-up self-test.
If the power-up self-test finds problems, an error code appears on the
screen. Refer to Chapter 2 to correct any problems before continuing with
the option installation.
If the power-up self-test succeeds, turn the workstation off and remove
any covers as necessary. Refer to Chapter 3 for detailed instructions.

Installing Options 5–3

5.4 Changing the Configuration
Before you change the Q-bus configuration, be sure to consider the module
order in the backplane and the module configuration.

5.4.1 General Module Order
The order of modules in the backplane depends on four factors:
•

Relative use of devices in the system

•

Expected performance of each device relative to other devices

•

The ability of a device to tolerate delays between bus requests and
bus grants (delay tolerance)

•

The tendency of a device to prevent other devices farther from the
DWFQA Q-bus adapter from accessing the bus.

The recommended module order in a VAXstation 3520/3540 or 3820/3840
workstation is as follows:
TSV05
DSV11
CXY08
TQK70

5.4.2 Module Configuration
Each module in a system must use a unique device address and interrupt
vector. The device address is also known as the control and status register
(CSR) address. Most modules have switches or jumpers for setting the
CSR address and interrupt vector values. Calculating these values is
a complex procedure, because some modules use floating addresses and
vectors. The value of a floating address depends on what other modules
are installed in the system.
The VMS SYSGEN utility has a CONFIG program to determine CSR
addresses and interrupt vectors. The next section describes how to use
the CONFIG program.

5–4 Installing Options

5.4.3 Finding CSR Addresses and Interrupt Vectors
with the CONFIG Program
You use the CONFIG program in the VMS SYSGEN utility to determine
the correct CSR address and interrupt vector for a module. You type
in a list of devices in the system. CONFIG automatically provides CSR
address and interrupt vector information.
The CONFIG program uses a standard Q22-bus algorithm to determine
the correct CSR addresses and interrupt vectors. You must use this
method, so the operating system can recognize the CSR addresses and
interrupt vectors. You can use these settings in VMS, ULTRIX-32m, and
VAXELN systems.
To use SYSGEN, you must have system manager privileges. The
assignment process is automated. You enter device names, and SYSGEN
assigns the devices according to how the system is configured. Use
SYSGEN as follows:
1. Log into the system manager account.
2. Enter MCR SYSGEN to access the SYSGEN utility as follows:
$ MCR SYSGEN

3. At the SYSGEN> prompt, enter the CONFIGURE command.
SYSGEN responds by issuing the DEVICE> prompt.
SYSGEN>CONFIGURE
DEVICE>

4. At the DEVICE> prompt, enter all the devices currently in the system
and all the devices you want to add to the system. Table 5–1 lists the
abbreviations. Example 5–1 shows a sample SYSGEN utility display.

Installing Options 5–5

DEVICE> TU81
DEVICE> DHV11

Example 5–1

Sample Output Using the SYSGEN CONFIG Program

5. To check how SYSGEN has configured the system, type Ctrl Z at the
DEVICE> prompt. Then exit SYSGEN.
DEVICE> Ctrl Z
Device: TU81 Name: PTA
Device: DHV11 Name: TXA

CSR: 774500
CSR: 760440*

Vector: 260
Vector: 300*

Support: yes
Support: no

Table 5–1 Device Abbreviations Used with SYSGEN
Device

Enter at DEVICE> Prompt

CXY08

DHV11

DSV11

TQK70

TU81

TSV05

TS11

5.5 Testing a New Configuration
After installing an option, test the new configuration by pressing the
Restart/Run button on the control panel. The workstation unit will check
its new configuration and perform a power-up self-test.
If the workstation displays an error code, check all system unit
connections and press the Restart/Run button again. If an error still
occurs, install an option from a different option kit. If necessary, follow
the troubleshooting procedures described in Chapter 2.

5–6 Installing Options

5.6 CXY08 8-Line Asynchronous Multiplexer
The CXY08 asynchronous multiplexer performs data concentration, realtime processing, and interactive terminal handling. The CXY08 is a
quad-height module with a BA200 series handle. The CXY08 option also
includes two cable assemblies. The module provides eight full-duplex
serial data channels. Each cable assembly has a four-channel distributor.
All eight channels allow autoanswer dial-up operation over the publicswitched telephone network. You can use AT&T 103, 113, and 212
modems, or the equivalent.
To install the CXY08 asynchronous multiplexer:
The CXY08 asynchronous multiplexer is a Q-bus option. Before you
install the CXY08, you must install the Q-bus adapter in slot 9, if the
adapter is not already installed. See Section 5.9.
CAUTION
Static electricity can damage integrated circuits. Use the wrist
strap and antistatic mat found in the antistatic kit (29–26246–00)
when you work with the internal parts of a computer system.
To install the CXY08 in the backplane, remove the cover from the Q-bus
slot where you are installing the module. To determine the location of
the CXY08 module in the backplane, follow the module order list in
Section 5.4.1. If the module has a recessed handle, you must add a gap
filler.
To configure the CXY08 option:
Select the CSR address and interrupt vector for the CXY08 by using DIP
switches on the module (Figure 5–1). The CXY08 uses a floating CSR
address and interrupt vector.

Installing Options 5–7

E36
DHV

DHC

E28

Closed = 1 = On

Open = 0 = Off

Closed
V3

A12

Manf.
Test

Open

MA-X0698-89

Figure 5–1

CXY08 Module Layout

5–8 Installing Options

The CXY08 factory positions are as follows:
CXY08 CSR Address: 17760440 (factory position)
________________________________________________________________
Address Bits: A12
A11 A10 A9
A8 A7 A6
A5 A4
E36 Switches: 2
3
4
5
6
7
8
9
10
________________________________________________________________
CSR Address
17760440:
0
0
0
0
1
0
0
1
0
________________________________________________________________
1 = closed, 0 = open
CXY08 Interrupt Vector: 300 (factory position)
________________________________________________________________
Vector Bits:
V8 V7 V6
V5 V4 V3
E28 Switches: 3
4
5
6
7
8
________________________________________________________________
Vector
Address 300:
0
1
1
0
0
0
________________________________________________________________
1 = closed, 0 = open

Switch E36–1 selects DHV11 or DHU11 programming mode. Select the
mode appropriate to the device driver in the system. Generally, DHU11
mode gives better performance because it does not require as much CPU
time. To select DHU11 mode, set the switch to 1 (closed).
Switch E28–1 should be set to 1 (closed), and switch E28–2 should be set
to 0 (open). These switches are used during manufacturing.

Installing Options 5–9

5.7 DSV11 Communications Option
The DSV11 is a two-channel, high-speed, synchronous communications
option for use on Q-bus backplanes. Figure 5–2 shows the DSV11–S
option.
The DSV11 supports the following synchronous communications protocols:
DDCMP
HDLC/SDLC
BISYNC
The DSV11 allows any of the following synchronous interfaces:
RS–423
RS–422
RS–232/V.24
V.35
To install the DSV11 option:
The DSV11 is a Q-bus option. Before you install the DSV11, you
must install the Q-bus adapter in slot 9 (if not already installed). See
Section 5.9.
CAUTION
Static electricity can damage integrated circuits. Use the wrist
strap and antistatic mat found in the antistatic kit (29–26246)
when you work with the internal parts of a computer system.
To install the DSV11 in the backplane, remove the cover from the Q-bus
slot where you are installing the module. To determine the location of
the DSV11 module in the backplane, follow the module order list in
Section 5.4.1. If the module has a recessed handle, you must add a gap
filler.

5–10 Installing Options

LE D

Fac t or y Set t ings
Switch On (Closed) = 0

Switch Off (Open) = 1
MA-X0014-88

Figure 5–2

DSV11–S Module Layout (M3108–PA)

Installing Options 5–11

To configure the DSV11 option:
Use switchpack E32 (Figure 5–2) to set the CSR address. The CSR
address floats. The actual DSV11 settings depend on the other modules in
the system.
The interrupt vector also floats. It is set by the software and cannot be
changed by switches.
Use switchpack E89 (Figure 5–2) to select the DSV11 bus grant and DMA
continuity.
The following tables list the configurations for the CSR address and for
the bus grant and DMA continuity:
DSV11 CSR Address: 17760640 (factory position)
Switchpack E32
________________________________________________________________
Address Bits: A12
A11 A10 A9 A8 A7 A6
A5 A4 A3
E32 Switches: 1
2
3
4
5
6
7
8
9
10
________________________________________________________________
CSR Address:
17760640
0
0
0
0
1
1
0
1
0
0
17760740
0
0
0
0
1
1
1
1
0
0
________________________________________________________________
1 = open, 0 = closed
DSV11 Bus Grant and DMA Continuity
Switchpack E89
________________________________________________________________
E89 Switches
1 2 3
4 5 6
________________________________________________________________
DSV11-M, Q/Q Slots
0 0 0
0 0 0 (factory position)
DSV11-M, Q/CD Slots
0 0 0
0 1 1
DSV11-SF
0 0 0
0 1 1 (factory position)
________________________________________________________________
1 = open, 0 = closed

5–12 Installing Options

5.8 Expansion Modules
The following sections describe the installation of the memory, CPU, and
graphics expansion modules.

5.8.1 Memory Expansion Module
The MS60 memory module option comes in three sizes:
•
•
•

MS60-AA—8 Mbytes
MS60-BA—16 Mbytes
MS60-CA—32 Mbytes

You install a memory expansion module in slot 5, 6, or 9 of the card cage.
To install a memory expansion module (observing antistatic
procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the I/O cover (Section 3.4).
4. Slide the memory expansion module into slot 5, 6, or 9 of the card
cage. Lock the module in place by simultaneously pushing down on
the top release lever and pulling up on the bottom release lever.
5. Replace the I/O cover.
6. Turn on the workstation.
7. Test the new configuration.
8. Replace the front cover.

5.8.2 CPU Expansion Module
You install the CPU expansion module in slot 6 of the card cage. An
upgrade medallion comes with the module.
To install a CPU module (observing antistatic procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the I/O cover (Section 3.4).
4. Slide the CPU expansion module into slot 6 of the card cage. Lock the
module in place by simultaneously pushing down on the top release
lever and pulling up on the bottom release lever.

Installing Options 5–13

5. Replace the I/O cover.
6. Turn on the workstation.
7. Test the new configuration.
8. Replace the front cover.
9. Peel the VAXstation 3520 or 3820 medallion off the front cover and
replace it with the VAXstation 3540 or 3840 medallion.

5.8.3 Graphics Expansion Module
The graphics expansion module is a graphics bus option that expands the
workstation’s graphic subsystem from 8 planes of memory to 24 planes.
You install the graphics expansion module in slot 1 of the card cage.
To install a graphics expansion module (observing antistatic
procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the graphics cover (Section 3.5).
4. Remove the graphics frontplane assembly (Section 3.6).
5. Slide the graphics expansion module into slot 1 of the card cage.
Lock the module in place by simultaneously pushing down on the top
release lever and pulling up on the bottom release lever.
6. Replace the graphics frontplane assembly.
7. Replace the graphics cover.
8. Turn on the workstation.
9. Test the new configuration.
10. Replace the front cover.

5–14 Installing Options

5.9 Q-bus Adapter Module
The Q-bus adapter module is a single M-bus module that provides an
interface between the workstation’s proprietary M-bus and the Q-bus.
The Q-bus adapter module is installed in slot 9, and the supported Q-bus
modules are installed in slots 10 through 12.
NOTE
The Q-bus adapter module must be installed in slot 9 in order for
the Q-bus modules installed in slots 10 through 12 to work.
To install the Q-bus adapter module (observing antistatic procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the I/O cover (Section 3.4).
4. Slide the Q-bus adapter module into slot 9 of the card cage. Lock the
module in place by simultaneously pushing down on the top release
lever and pulling up on the bottom release lever.
5. Replace the I/O cover.
6. Turn on the workstation.
7. Test the new configuration.
8. Replace the front cover.

Installing Options 5–15

5.10 RRD40 Optical Compact Disc Drive
The RRD40 optical compact disc drive is outside the system unit and
connects to the workstation by means of a SCSI cable. The option kit
includes the drive, preinstalled in an expansion box, and a power cord.
Before you install an optical compact disc drive, you must configure the
drive for a unique SCSI ID address. To find an open ID address for the
drive, display the system’s SCSI configuration on the screen by typing
show scsi. Use Table 5–2 to set the correct SCSI ID switches on the back
of the drive.

DEFM081

Table 5–2 RRD40 SCSI ID Switch Settings
Switch Settings
SCSI ID

0
1
2
3
4
5
6
7

Down
Down
Down
Down
Up
Up
Up
Up

Down
Down
Up
Up
Down
Down
Up
Up

Down
Up
Down
Up
Down
Up
Down
Up

Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used

3 Switch 4 is not used, so it can be in either position.

5–16 Installing Options

The SCSI bus runs from the I/O module, up into the mass storage area,
around the back of the mass storage area, and back to the front of the
mass storage area. The SCSI bus ends in a terminator at the front of the
mass storage cover.
To install an optical compact disc drive (observing antistatic
procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Verify that the SCSI ID switches are set correctly on the drive.
4. Remove the SCSI terminator from the front of the mass storage area.
Note that the SCSI bus must have a terminator. The terminator is a
standard size and will be used to terminate the optical compact disc
drive.
5. Connect the right-angle end of the SCSI cable to the SCSI connector.
CAUTION
Using a cable other than the Digital-supplied 7-foot SCSI cable
can cause the device to malfunction.
Route the SCSI cable down through the system unit and out the
bottom of the chassis. Connect the other end of the SCSI cable to the
top connector on the back of the drive.
Drive Cable

Drive Connector

DEFM069

Installing Options 5–17

6. Place the terminator on the bottom connector on the back of the drive.

Wire Brackets

Terminator

Drive Connector
DEFM070

7. Connect the power connector to the drive and plug the power cord into
the power source.
8. Turn on the drive.
9. Turn on the workstation.
10. Test the new configuration.
11. Run diagnostic tests to test the drive.
12. Replace the front cover.
For more information about the RRD40 drive, see the RRD40 Owner’s
Manual.

5–18 Installing Options

5.11 Tape or Q-bus Adapter Module
The tape adapter module is a single M-bus module that provides an
interface between the workstation’s proprietary M-bus and the TQK70
tape drive controller module, which is on the Q-bus. The tape adapter
module or the Q-bus adapter module must be installed in slot 9 in order
for the TQK70 tape drive controller module in slot 10 to work.
To install the tape adapter module (observing antistatic procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Remove the I/O cover (Section 3.4).
4. Slide the tape adapter module or the Q-bus adapter module into slot 9
of the card cage. Lock the module in place by simultaneously pushing
down on the top release lever and pulling up on the bottom release
lever.
5. Replace the I/O cover.
6. Turn on the workstation.
7. Test the new configuration.
8. Replace the front cover.

Installing Options 5–19

5.12 TK70 Tape and RZ55/RZ56 Disk Drives
Before you install a TK70 tape drive, an RZ55 hard disk drive, or an RZ56
hard disk drive, you must install slide supports on the drives so that you
can slide the drives in and out of the drive slots in the mass storage area.
Slide supports consist of top and bottom drive mounting brackets attached
to the drive, and top and bottom drive shock mounts attached to the mass
storage area.
If there are drive shock mounts already installed on your system, it is
important to remove them and install the drive shock mounts that came
with the drive option kit.

5.12.1 Installing Drive Shock Mounts
There are four drive shock mounts with screws included in the option kits
for the TK70 tape drive, the RZ55 hard disk drive, and the RZ56 hard
disk drive.
To install the shock mounts in the drive slot:
1. Attach two of the top shock mounts. Position each shock mount so the
screws on the mount go into the captive nuts on the roof of the mass
storage area. Tighten the screws.
2. Attach two of the bottom shock mounts to the bottom of the drive slot,
as shown. Position each shock mount so the screws on the mount go
into the captive nuts on the floor of the mass storage area. Tighten
the screws.
NOTE
One of the bottom shock mounts has a thin metal finger that
must be attached between the back screw and the system unit
frame to ground the shock mount to the chassis.

5–20 Installing Options

Rubber
Shock Mount
Drive Track

DEFM075

Installing Options 5–21

5.12.2 Installing Drive Mounting Brackets
Drive mounting brackets and screws are included in the option kits for
the TK70 tape drive, the RZ55 hard disk drive, and the RZ56 hard disk
drive.
There are three different situations for installing drive mounting brackets:
•
•
•

On a TK70 tape drive
On an RZ55 or RZ56 hard disk drive to be installed in the far-right
drive slot (because there is no tape drive)
On an RZ55 or RZ56 hard disk drive to be installed in any slot except
the far-right slot

To install drive mounting brackets for a TK70 tape drive:
1. Attach the top bracket to the top of the drive, using two screws.
2. Attach the bottom bracket to the bottom of the drive, using two
screws.

Drive
Mounting
Brackets

DEFM056

5–22 Installing Options

To install drive mounting brackets for an RZ55 hard disk drive
that will reside in the far-right slot (because there is no tape
drive):
1. Attach the top bracket to the top of the drive, using two screws.
2. Attach the bottom bracket to the bottom of the drive, using two
screws.
SCSI Cable
Drive Mounting Bracket

Captive
Screws

Power Cable
RZ55 Disk Drive
DEFI055

Drive Mounting Bracket

Installing Options 5–23

To install drive mounting brackets for an RZ55 hard disk drive
that will reside in any slot except the far-right slot:
1. Attach the top bracket to the top of the drive, using two screws.
2. Attach the bottom bracket to the bottom of the drive, using two
screws.
RZ55 Disk Drives

Drive Mounting Bracket
Captive Screw
SCSI Connector

Power Connector

Captive
Screw

Drive Mounting Bracket
DEFI056

5–24 Installing Options

To install drive mounting brackets for an RZ56 hard disk drive
that will reside in the far-right slot (because there is no tape
drive):
1. Attach the top bracket to the top of the drive, using two screws.
2. Attach the bottom bracket to the bottom of the drive, using two
screws.

Drive Mounting Bracket

Captive
Screws

DEFM079

Drive Mounting Bracket

Installing Options 5–25

To install drive mounting brackets for an RZ56 hard disk drive
that will reside in any slot except the far-right slot:
1. Attach the top bracket to the top of the drive, using two screws.
2. Attach the bottom bracket to the bottom of the drive, using two
screws.

Drive Mounting Bracket

Captive
Screws

DEFM080

Drive Mounting Bracket

5–26 Installing Options

5.12.3 TQK70 Tape Drive Controller Module
The TQK70 tape drive controller module connects to and controls the
TK70 tape drive. The TQK70 is a dual-height Q-bus module.
NOTE
You must install the tape adapter module in slot 9 before you
install the TQK70 in slot 10, or you must install the Q-bus adapter
module in slot 9 before you install the TQK70 in slot 10, 11, or 12.
To determine the location of the TQK70 module in the backplane, follow
the module order list in Section 5.4.1. If the module has a recessed
handle, you must add a gap filler.
To install the tape drive controller module (observing antistatic
procedures):
1. Turn off the workstation.
2. Configure the tape drive controller module by setting the base
address, interrupt vector address, and programming mode. (Refer
to the TQK70 User’s Guide.)
3. Remove the front cover from the system unit (Section 3.3).
4. Determine which slot to install the TQK70, following the preferred
module order (Section 5.4.1).
5. Remove the blank cover from the appropriate Q-bus slot.
6. Slide the tape drive controller module into the top of the Q-bus slot.
7. Slide the blank panel into the bottom of the Q-bus slot.

Installing Options 5–27

Slot 10

TK70 Tape Drive
Controller Module

DEFM054

8. Remove the mass storage cover.
9. Connect the tape drive controller-to-TK70 cable to the tape drive
controller connector. Route the cable up through the mass storage
area to the back of the far-right drive slot.
NOTE
When you attach the cable to the controller module, follow the
instructions on the cable connector’s green label as to which
side must face up.

5–28 Installing Options

5.12.4 TK70 Tape Drive
The TK70 tape drive is a streaming tape drive subsystem that provides
up to 296 Mbytes of data storage on a single cartridge. The TK70 tape
drive connects to and is controlled by the TQK70 tape drive controller
module.
The TK70 always installs in the far-right drive slot of the mass storage
area.
To install the TK70 tape drive (observing antistatic procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3).
3. Install the TQK70 tape drive controller module (Section 5.12.3).
4. Remove the mass storage cover (Section 3.8).
5. Remove the control panel assembly (Section 4.2.4).
6. Install drive shock mounts in the far-right mass storage slot
(Section 5.12.1).
7. Install drive mounting brackets on the tape drive (Section 5.12.2).
8. Route the cable from the TQK70 module up through an opening in the
divider between the card cage and the mass storage area.
9. Connect that cable and the cable from the power supply to the back of
the tape drive.
NOTE
When you attach the cable to the controller module, follow the
instructions on the cable connector’s green label asto which
side must face up.
10. Align the drive mounting brackets with the top and bottom shock
mounts before you begin to slide the drive into the mass storage area.

Installing Options 5–29

11. Slide the drive into the far-right slot in the mass storage area.
SCSI Cable
Drive Mounting Bracket

Captive Screws

Power
Cable
Drive Mounting Bracket
DEFM058

12. Secure the drive to the mass storage area by turning the captive
screws on both drive mounting brackets.
13. Replace the control panel.
14. Replace the mass storage cover.
15. Turn on the workstation.
16. Test the new configuration.
17. Run diagnostic tests to test the drive.
18. Replace the front cover.
For more information about the TK70 drive, refer to the TK70 Tape Drive
Installation Guide.

5–30 Installing Options

5.12.5 Internal RZ55 Hard Disk Drive
The internal RZ55 hard disk drive is preformatted at the factory to
provide a storage capacity of 332 Mbytes. The system unit can hold
up to four internal RZ55 drives in the mass storage area.
Always install and number RZ55 drives from right to left, starting with
drive 0 and using drive jumpers to set the disk drive ID value. Before you
install an internal RZ55 drive, your drive must be configured for a unique
SCSI ID address. Display the system’s SCSI configuration on the screen
by typing show scsi to find an open ID address for the drive.
Use Table 5–3 to set the correct disk drive ID value on the RZ55 drive.

Drive ID
Jumpers

Captive Screws

Table 5–3 Internal RZ55 Disk Drive SCSI ID Settings
Jumper Settings
Drive ID

0
1
2
3
4
5
6
7

Out
In
Out
In
Out
In
Out
In

Out
Out
In
In
Out
Out
In
In

Out
Out
Out
Out
In
In
In
In

DEFM037

Installing Options 5–31

RZ55 drives connect to the SCSI bus. The SCSI bus runs from the I/O
module, up into the mass storage area, around the back of the tape drive
cavity, and back to the front of the mass storage area.
To install an RZ55 drive (observing antistatic procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3) .
3. Remove the mass storage cover (Section 3.8).
4. Remove the control panel (Section 4.2.4).
5. Install drive shock mounts in the mass storage slot (Section 5.12.1).
6. Install drive mounting brackets on the drive (Section 5.12.2).
7. Verify that the SCSI ID switches are set correctly for each disk drive
you are installing (Table 5–3).
8. Slide the drive into the rightmost available slot in the mass storage
area, aligning the drive mounting brackets with the top and bottom
shock mounts in the mass storage slot.
•

If you install the RZ55 hard disk drive in the far-right slot of
the mass storage area, you must installed the drive with the
connectors facing the back of the mass storage area, as shown.
SCSI Cable
Drive Mounting Bracket

Captive
Screws

Power Cable
RZ55 Disk Drive
DEFI055

Drive Mounting Bracket

5–32 Installing Options

•

The following figure shows how to install the RZ55 in a slot other
than the far-right slot of the mass storage area.
RZ55 Disk Drives

Drive Mounting Bracket
Captive Screw
SCSI Connector

Power Connector

Captive
Screw

Drive Mounting Bracket
DEFI056

9. Secure the drive to the mass storage area by turning the captive
screws on both drive mounting brackets.
10. Connect the SCSI cable connector for the drive slot to the drive.
11. Connect the power connector to the connector on the drive.
12. Replace the control panel.
13. Replace the mass storage cover.
14. Turn on the workstation.
15. Test the new configuration.
16. Run diagnostic tests to test the drive.
17. Replace the front cover.
For more information about the RZ55 drive, refer to the RZ55 Disk Drive
Service Manual.

Installing Options 5–33

5.12.6 Internal RZ56 Hard Disk Drive
The internal RZ56 hard disk drive is preformatted at the factory to
provide a storage capacity of 665 Mbytes. The system unit can hold
up to four internal RZ56 drives in the mass storage area.
Always install and number RZ56 drives from right to left, starting with
drive 0 and using drive jumpers to set the disk drive ID value. Before you
install an internal RZ56 drive, your drive must be configured for a unique
SCSI ID address. To find an open ID address for the drive, display the
system’s SCSI configuration on the screen by typing show scsi.
CPUxx >>> show SCSI

Use Table 5–4 to set the correct disk drive ID value on the RZ56 drive.
The following figure shows where to set the jumper settings on the drive.
Jumper setting 1 is the bottom row of pins.

Pin Sets:

1
2
3

Drive
Jumper

Drive ID

MA-X1002-89

5–34 Installing Options

Table 5–4 RZ56 Disk Drive SCSI ID Settings
Jumper Settings
Drive
ID

Out

The RZ56 drive connects to the SCSI bus. The SCSI bus runs from the
I/O module, up into the mass storage area, around the back of the tape
drive cavity, and back to the front of the mass storage area.
To install an RZ56 disk drive (observing antistatic procedures):
1. Turn off the workstation.
2. Remove the front cover from the system unit (Section 3.3) .
3. Remove the mass storage cover (Section 3.8).
4. Remove the control panel (Section 4.2.4).
5. Install drive shock mounts in the mass storage slot (Section 5.12.1).
6. Install drive mounting brackets on the drive (Section 5.12.2).
7. Verify that the SCSI ID switches are set correctly for each disk drive
you are installing (Table 5–4).
8. Slide the drive into the rightmost available slot in the mass storage
area, aligning the drive mounting brackets with the top and bottom
shock mounts in the slot.

Installing Options 5–35

•

If you are installing the RZ56 disk drive in the far-right slot of the
mass storage area, you must install the drive with the connectors
facing the back of the mass storage area, as shown.
SCSI Cable
Drive Mounting Bracket

Captive
Screws

Power Cable
RZ56 Disk Drive

Drive Mounting Bracket

DEFI055A

•

The following figure shows how to install the RZ56 disk drive into
any slot other than the far-right slot of the mass storage area.
RZ56 Disk Drives

Drive Mounting Bracket
Captive Screw
SCSI Connector

Power Connector

Captive
Screw

Drive Mounting Bracket
DEFI056A

5–36 Installing Options

9. Secure the drive to the mass storage area by turning the captive
screws on both drive mounting brackets.
10. Connect the power connector to the connector on the drive.
11. Connect the SCSI cable to the connector on the drive
12. Replace the control panel and the mass storage cover.
13. Turn on the workstation.
14. Test the new configuration.
15. Replace the workstation covers.
For more information about the RZ56 drive, refer to the RZ56 Disk Drive
Service Manual.

5.13 TS05 Tape Drive
The TS05 is a magnetic streaming tape drive that provides 40.5 Mbytes
of backup data storage. The TS05 reads or writes up to 160 Kbytes/s
in standard ANSI format. The drive uses automatic read after write to
verify that data is accurately recorded.
To install the TS05 tape drive:
The TS05 tape drive is a Q-bus option. Before you install the TSV05
controller and the TS05 tape drive, you must install the Q-bus adapter in
slot 9 (if not already installed).
NOTE
A tape drive system includes two ribbon cables, two 50-conductor
cables, and two type-A filtered connectors.
You install the TS05 in the top 26.3 cm (10.5 in.) mass storage shelf of
the H9642 cabinet. For information about installing the TS05 drive in the
H9642 cabinet, see the service documentation for the cabinet.
Tape data is buffered in 3.5 Kbytes of RAM on the drive’s TSV05
controller (M7530). The TSV05 is a tape mass storage control protocol
(TMSCP) device.
You install the TSV05 controller (Figure 5–3) in one of the Q-bus slots
(slots 10 through 12) in the backplane. Section 5.4.1 lists the preferred
module order.

Installing Options 5–37

CAUTION
Static electricity can damage integrated circuits. Use the wrist
strap and antistatic mat found in the antistatic kit (29–26246–00)
when you work with the internal parts of a computer system.
Front Panel

EMULEX

U15
J4
Novram

U43
Firmware
Prom

K
J
H
G
F
E
D

LED

SW2

Host
Adapter

2
1

SW1

Controller
(HAC)

OFF/ON
J2

U39
8031

C
U50

Buffer
Controller

MA-X0697-89

Figure 5–3

TSV05 (M7530) Controller Module

5–38 Installing Options

The M7530 CSR address is selected by DIP switches SW2-1 through
SW2-3 as shown below.
TSV05 Bus
Address

SW 2

772520
772524
772530
772534
772440
772444
772450
772454

0
1
0
1
0
1
0
1

0
0
1
1
0
0
1
1

0
0
0
0
1
1
1
1

Connect the two ribbon cables from the TS05 tape drive to the distribution
panel.
J3
out
J1
in

Front

J1
out

J3
in

Rear
MA-X0695-89

Installing Options 5–39

Two 50-conductor cables run between the distribution panel and the
TSV05 controller, as shown.

TSV05
Tape Coupler

in
J3

TSVO5
Distribution

out

J3
out

TS05 Drive
Tape Transport 0
(Formatter)

Panel

MA-X0694-89

The fan filter is a field replaceable unit (FRU) on the TS05 tape drive. See
the TS05 Pocket Service Guide for removal and replacement procedures.

A
Equipment Specifications
This appendix lists the physical specifications, operating conditions, and
nonoperating conditions for these units:
•

VS60S system unit

•

VR295 monitor

•

LK201 keyboard

•

VXXX-AA mouse

•

RZ55 hard disk drive

•

RZ56 hard disk drive

•

TK70 tape drive

•

RRD40 optical compact disc drive

A–1

A–2 Equipment Specifications

A.1 VS60S System Unit
Dimensions and Weight

System unit

Weight

Height

Width

Depth

40.5 kg

68.58 cm

53.34 cm

45.08 cm

90 lb
(unloaded)

27 in.

21 in.

17.75 in.

Specifications
Noise power emission level

5.7 decibels, intermittent 5.0 decibels,
continuous operation

Power

670 W

Operating Conditions
Temperature range

10° C to 40° C (50° F to 104° F)

Temperature change rate
maximum

11° C (20° F) per hour

Relative humidity

20% to 80%, noncondensing

Maximum wet bulb temperature

28° C (82° F)

Minimum dew point temperature

2° C (36° F)

Altitude

2400 m (8000 ft) at 36° C (96° F)

Nonoperating Conditions
Temperature range

–40° C to 66° C (–40° F to 151° F)

Relative humidity

10% to 95%, noncondensing

Maximum wet bulb temperature

46° C (115° F), packaged

Minimum dew point temperature

2° C (36° F)

Altitude

4900 m (16,000 ft) at 36° C (96° F)

Equipment Specifications A–3

A.2 VR295 Monitor
Dimensions and Weight

Monitor

Weight

Height

Width

Depth

33.75 kg
75 lb

46.99 cm
18.5 in.

50.8 cm
20 in.

54.61 cm
21.5 in.

Specifications
Viewable size (measured
diagonally)

48.3 cm (19 in.)

Resolution

1280 pixels x 1024 lines

Swivel on base

190°

Vertical tilt

–5° forward to 20° backward

Operating Conditions
Temperature range

10° to 40° C (50° to 104° F)

Relative humidity

10% to 95%, noncondensing

Maximum wet bulb temperature

32° C (90° F)

Minimum dew point temperature

2° C (36° F)

Altitude

2400 m (8000 ft) at 36° C (96° F)

Nonoperating Conditions
Temperature range

–40° C to 66° C (–40° F to 151° F)

Relative humidity

10% to 95%, noncondensing

Maximum wet bulb temperature

46° C (115° F), packaged

Minimum dew point temperature

2° C (36° F)

Altitude

4900 m (16,000 ft) at 36° C (96° F)

A–4 Equipment Specifications

A.3 LK201 Keyboard
Dimensions and Weight

Keyboard

Weight

Height

Width

Depth

2 kg
4.5 lb

51 mm
2 in.

533 mm
21 in.

171 mm
6.75 in.

Specifications
Number of keys

105

Indicators

4 status LEDs

Language variations

Diagnostics

Self-testing and self-identifying with
respect to revision level but not with
respect to language variations

Cable

1.76 m (6 ft) uncoiled, detachable; 4-pin
mmj connector at both ends

Baud rate

4800

Power consumption maximum

4.2 W

Power input

11.8 V ±6% @ 350 ma

Electrical interface

EIA RS–423

Volume control

8 levels, plus off. Maximum 65 dba 1 ft
above keyboard

Keystroke timing minimum

20 msec

Operating Conditions
Temperature range

10° C to 40° C (50° F to 104° F)

Relative humidity

10% to 90%

Maximum wet bulb temperature

2.8° C (82° F)

Minimum dew point temperature

2° C (36° F)

Altitude

2400 m (8000 ft) at 36° C (96° F)

Equipment Specifications A–5

Nonoperating Conditions
Temperature range

–40° C to 66° C (–40° F to 151° F)

Relative humidity

10% to 95%, noncondensing

Maximum wet bulb temperature

46° C (115° F), packaged

Minimum dew point temperature

2° C (36° F)

Altitude

49,000 m (16,000 ft) at 36° C (96° F)

A.4 VSXXX-AA Mouse
Dimensions and Weight

Mouse

Weight

Height

Diameter

0.37 kg
0.82 lb

4 cm
1.57 in.

8.8 cm
3.47 in.

Specifications
Baud rate

4800

Cable length

1.5 m (5 ft), shielded, 6 conductors and
terminals in a 7-pin micro-DIN-type
connector (male)

Resolution

79 counts/cm (200 counts/in)

Tracking speed

73.5 cm (30 in/s)

Electrical interfaces

EIA RS-232-C or TTL

Operating modes

Incremental or polling

Tracking rate

In incremental mode: 55 reports/s
In polling mode: up to 95 reports/s

Accuracy

±3% 0 to 24.5 cm/s (0 to 10 in/s) any
direction
±5% 24.5 to 49 cm/s (10 to 20 in/s) any
direction
±30% 49 to 73.5 cm/s (20 to 30 in/s) any
direction

Data format

Delta binary

Number of buttons

A–6 Equipment Specifications

Diagnostics

Self-testing and self-identifying with
respect to revision level

Power requirements

+5 V ±5% at 130 mA
–12 V ±10% at 20 mA

Operating Conditions
Temperature range

10° C to 40° C (50° F to 104° F)

Relative humidity

10% to 90%, noncondensing

Maximum wet bulb temperature

28° C (82° F)

Minimum dew point temperature

2° C (36° F)

Altitude

2400 m (8000 ft) at 36° C (96° F)

Nonoperating Conditions
Temperature range

–40° C to 66° C (–104° F to 140° F)

Relative humidity

5% to 95%

Maximum wet bulb temperature

46° C (115° F), packaged

Minimum dew point temperature

2° (36° F)

Altitude

4900 m (16,000 ft) at 36° C (96° F)

Equipment Specifications A–7

A.5 VSXXX-AB Tablet
Dimensions and Weight

Tablet

Weight

Height

Width

Depth

3.2 kg

2 cm

41.2 cm

40.6 cm

7 lb

8 in.

16 in.

16.2 in.

Specifications
Cable length

1.5 m (5 ft), terminated in a 7-pin MicroDIN-type connector

Active area

27.5 mm x 27.5 mm (11 in. x 11 in.)

Resolution

79 counts/cm (200 counts/in)

Proximity (nominal)

1.27 cm (5 in.) cursor
0.63 cm (0.25 in.) stylus

Baud rate

4800 or 9600 baud (software selectable)

Power requirements

+12 Vdc ±10% at 0.3A

Output connector (power and data)

7–pin Micro–DIN (male)

Mating connector

7–pin Micro–DIN (female)

Operating modes

Incremental and polling

Remote request

X–Y coordinate update and proximity
report when polled by host

Incremental

Position reports are generated as long
as cursor is in motion. Reports are also
generated when the pushbuttons are
pressed or released.

Interfaces

Serial, asynchronous, full-duplex, with
EIA RS-232-C signal levels

Tracking rates

In incremental mode: 55, 72, 120 reports/s
In polling mode: 50 reports/s at 4800 baud
and 80 reports/s at 9600 baud

Puck

4 buttons

Stylus

2 buttons

A–8 Equipment Specifications

Diagnostics

Self-testing and self-identifying (revision
level and the fact that it is not a
mouse). Diagnostics check electronics,
communication, tablet, and transducers.

Operating Conditions
Temperature range

10° C to 40° C (50° F to 104° F)

Relative humidity

20% to 80%, noncondensing

Maximum wet bulb temperature

28° C (82° F)

Minimum dew point temperature

2° C (36° F)

Altitude

2400 m (8000 ft) at 36° C (96° F)

Nonoperating Conditions
Temperature range

–40° C to 66° C (–40° F to 151° F)

Relative humidity

10% to 95%, noncondensing

Maximum wet bulb temperature

46° C (115° F), packaged

Minimum dew point temperature

2° C (36° F)

Altitude

4900 m (16,000 ft) at 36° C (96° F)

Equipment Specifications A–9

A.6 RZ55 SCSI Hard Disk Drive
Dimensions and Weight

Internal drive

Weight

Height

Width

Depth

3.78 kg
8.4

8.25 cm
3.25 in.

14.60 cm
5.75 in.

20.82 cm
8.20 in.

Specifications
Capacity

332.3 Mbytes

Per surface

22.48 Mbytes

Per track

18,432

Per block

512 bytes

Blocks/track

Blocks/drive

649,040

Spare blocks/cylinder

Spare blocks/drive

10,300

Transfer rate to/from media

1.25 Mbytes/s

Bus asynchronous mode

1.5 Mbytes/s

Bus synchronous mode

4.0 Mbytes/s

Seek time, track-to-track

4 msec

Seek time, average

16 msec

Seek time, maximum

35 msec

Average rotational latency

8.3 msec

Rotational speed

3600 rev/min ±0.5%

Start time, maximum

20 sec

Stop time, maximum

20 sec

Interleave

1:1

Bus latency maximum

600 µsec

Heat dissipation

28 W (typical)
32 W (random seek mode)

Recording density

21,231 bits/in. at ID

A–10 Equipment Specifications

Track density

1075 tracks/in.

Tracks/surface (unformatted)

1224

R/W heads

Operating Conditions
Temperature range3

10° C to 55° C (50° F to 131° F)

Relative humidity

8% to 80%

Maximum wet bulb temperature

25.6° C (78° F), noncondensing

Minimum dew point temperature

2° C (36° F)

Altitude

–304 to 4600 m (–1000 to 15000 ft) at 36°
C (96° F)

3 Reduce maximum temperature by 1.8° C (3.24° F) for each 1000-meter increase in altitude.

Nonoperating Conditions
Temperature range

–40° C to 66° C (–40° F to 151° F)

Relative humidity

8% to 95%, packaged

Maximum wet bulb temperature

46° C (115° F), packaged, noncondensing

Minimum dew point temperature

2° C (36° F)

Altitude

–304 to 12,300 m (–1000 ft to 40,000 ft) at
36° C (96° F)

Equipment Specifications A–11

A.7 RZ56 Hard Disk Drive
Dimensions

Internal drive

Weight

Height

Width

Depth

3.78 kg
8.4 lbs

8.25 cm
3.25 in

14.60 cm
5.75 in

20.0 cm
8.0 in

Specifications
Capacity

665.17 Mbytes

Per surface

50.9 Mbytes

Per track

31,248

Per block

512 bytes

Blocks/track

Blocks/drive

1,299,174

Spare blocks/cylinder

Spare blocks/drive

20,316

Space cylinders

Transfer rate to/from media

1.25 Mbytes/s

Bus asynchronous mode

1.6 Mbytes/s

Bus synchronous mode

4.0 Mbytes/s

Seek time, track-to-track

4 msec

Seek time, average

16 msec

Seek time, maximum

35 msec

Average rotational latency

8.3 msec

Rotational speed

3600 rev/min ±0.5%

Start time, maximum

20 sec

Stop time, maximum

20 sec

Interleave

1:1

Bus latency maximum

600 µsec

Heat dissipation

28 W (typical)
32 W (random seek mode)

A–12 Equipment Specifications

Recording density

31,846 bits/in. at ID

Track density

1440 tracks/in.

Tracks/surface (unformatted)

1632

Tracks/surface (formatted)

1626

R/W heads

Disks

Time to process ECC (512 bytes)

100 msec

Operating Conditions
Temperature range3

10° C to 55° C (50° F to 131° F)

Relative humidity

8% to 80%

Maximum wet bulb temperature

25.6° C (78° F), noncondensing

Minimum dew point temperature

2° C (36° F)

Altitude

–304 to 4600 m (–1000 to 15000 ft)
at 36° C (96° F)

3 Reduce maximum temperature by 1.8° C (3.24° F) for each 1000 meter increase in altitude.

Nonoperating Condition
Temperature range

–40° C to 66° C (–40° F to 151° F)

Relative humidity

8% to 80%

Maximum wet bulb temperature

46° C (115° F), packaged,
noncondensing

Minimum dew point temperature

2° C (36° F)

Altitude

–304 to 12,300 m (–1000 ft to
40,000 ft) at 36° C (96° F)

For additional information on the RZ56 drive, see the RZ56 Disk Drive
Service Manual.

Equipment Specifications A–13

A.8 TK70 Tape Drive
Dimensions and Weight

Internal drive

Weight

Height

Width

Depth

2.27 kg

8.25 cm

14.6 cm

21.44 cm

5.0 lb

3.235 in

5.7 in

8.44 in

Specifications
Mode of operation

Streaming

Media

12.77 mm (1/2-in) magnetic tape

Bezel

5.87 x 3.40 x 0.350 inches

Bit density

10,000 bits/in

Number of tracks

Transfer rate (at host)

125 Kbytes/s

Tape speed

100 in/s

Track format

Multiple track serpentine recording

Cartridge capacity

94 Mbytes (approximately), formatted

Power requirements

12 V ±5% at 2.0 A (2.4 A surge),
+5 V ±5% at 1.3 A (1.5 A surge)

Drive power, maximum

40 W

Host adapter (TQK70) power,
maximum

15 W

Operating Conditions
Temperature range3

10° C to 40° C (50° F to 104° F)

Relative humidity

20% to 80%, noncondensing

Maximum wet bulb temperature

25° C (77° F)

Minimum dew point temperature

2° C (36° F)

Altitude

2400 m (8000 ft) at 36° C (96° F)

3 Reduce maximum temperature by 1.8° C (3.24° F) for each 1000-meter increase in altitude.

A–14 Equipment Specifications

Nonoperating Conditions (Without Tape Cartridge)
Temperature range

–40° C to 66° C (–40° F to 151° F)

Relative humidity

10% to 95%

Maximum wet bulb temperature

46° C (115° F), packaged

Minimum dew point temperature

2° C (36° F)

Altitude

30,000 ft at 36° C (96° F)

A.9 RRD40 Optical Compact Disc Drive (Tabletop)
Dimensions and Weight

Expansion box

Weight

Height

Width

Depth

4.0 kg

76.2 mm

229 cm

280 cm

8.8 lb

3 in

9.125 in

11 in

Specifications
Capacity/disc

635 Mbytes

Access time

Maximum 1000 msec, including latency
average 500 msec

Average latency

155 msec at outer track
60 msec at inner track

Average transfer rate

175.2 Kbytes/s

Initialization startup time

Less than 6 sec

Heat dissipation

14 W (typical)

Operating Conditions
Temperature range3

10° C to 50° C (50° F to 122° F)

Relative humidity

10% to 80%, noncondensing

Maximum wet bulb temperature

28° C (82° F)

Minimum dew point temperature

2° C (36° F)

Altitude

3400 m (11,150 ft) at 36° C (96° F)

3 Reduce maximum temperature by 1.8° C (3.24° F) for each 1000-meter increase in altitude.

Equipment Specifications A–15

Nonoperating Conditions
Temperature range

4° C to 70° C (40° F to 158° F)

Relative humidity

5% to 95%, noncondensing

Maximum wet bulb temperature

46° C (115° F), packaged

Minimum dew point temperature

2° C (36° F)

Altitude

13,600 m (44,600 ft) at 36° C (96° F)

B
Part Numbers
This appendix lists the part numbers for
•

System FRUs

•

Hardware option kits

•

Hardware and software documentation

B.1 System FRUs
Table B–1 System FRUs
Item

Part Number

Components
LK201 keyboard (North American/U.K.)

LK201-AA

LK201 keyboard (other)

LK201-XX

Mouse

VSXXX-AA

RRD40 optical compact disc drive, 635 Mbytes

RRD40-DA

RZ55 hard disk drive, 332 Mbytes

RZ55-E

RZ56 hard disk drive, 665 Mbytes

RZ56-E

Tablet

VSXXX-AB

TK70 tape drive, 296 Mbytes

TK70-EA or
TK70E-SA

TS05 tape drive, 40.5 Mbytes

TS05-AA/-AB

VR295 monitor 120 V

VR295-DA

VR295 monitor, 240 V, Northern Hemisphere

VR295-D3

VR295 monitor, 240 V, Southern Hemisphere

VR295-D4

B–1

B–2 Part Numbers

Table B–1 (Cont.) System FRUs
Item

Part Number

Modules and Assemblies
Backplane assembly (3520/3540 systems)

70-24589-01

Backplane assembly (3820/3840 systems)

70-24589-02

Control panel assembly

70-26174-01

CXY08 asyncronous interface module

M3119-YA

DSV11 synchronous I/O interface module

M3108-PA

DWFQA Q-bus adapter module

L2002-00

Graphics base module

L2004-00

Graphics expansion module, 16 planes

L2006-AA

Graphics frontplane assembly

70-24583-01

Graphics output module, 8 planes

L2005-AA

I/O cover assembly

70-24582-01

I/O module

L2003-00

KA60-AA dual CPU module (3520/2540 systems)

L2001-00

KA60-BA dual CPU module (3820/2840 systems)

L2010-AA

MS60-AA memory module, 8 Mbytes

L2007-AA

MS60-BA memory module, 16 Mbytes

L2007-BA

MS60-CA memory module, 32 Mbytes

L2007-CA

Tape adapter module (for FTAM)

L2008-00

TQK70 tape controller module

M7559-00

TSV05 tape controller module

M7530-PA

Video cable assembly

17-01864-01

Electrical/Mechanical Parts
AC filter

70-23769-01

AC switch assembly

70-23999-01

AC switch frame

74-35417-01

Part Numbers B–3

Table B–1 (Cont.) System FRUs
Item

Part Number

Electrical/Mechanical Parts
Adapter, 25-pin D-sub. to 6-pin LAN (H8571-A)

12-23599-01

Battery

12-19245-01

Blank cover, single-width

70-23981-01

Blank panel

74-33507-01

Cable, backplane to control panel, 10-position

17-01964-01

Cable, backplane to fans, 5-position

17-01360-01

Cable, RH power harness

17-01362-01

Cable, LH power harness

17-01362-02

Cable, modem/communications, 10 feet (BCC38)

17-01862-01

Cable, printer LAN (BC16E-10)

17-00811-02

Cord, system unit power

17-00083-43

Cover, graphics

70-24581-01

Cover, mass storage

70-26175-01

Drive slide support screws

90-08404-02

Ethernet, ThinWire T-connector (H8223-A)

12-25869-01

Ethernet, ThinWire terminator (H8225-AA)

12-26318-01

Ethernet, ThinWire cable (BC16M)

17-01241-04

Ethernet, ThickWire cable, 5 meters (BNE4F-05)

17-01863-01

Fan assembly (both fans)

70-23998-01

Power supply, 120 V

H7868-A

Power supply, 240 V

7868-B

SCSI terminator, 50-pin

12-30552-01

RZ55 bracket, right (attaches to drive)

74-38204-02

RZ55 bracket, left (attaches to drive)

74-38204-01

RZ55 shock mount, right (attaches to enclosure)

70-25452-05

RZ55 shock mount, left (attaches to enclosure)

70-25452-06

B–4 Part Numbers

Table B–1 (Cont.) System FRUs
Item

Part Number

Electrical/Mechanical Parts
RZ56 bracket, right (attaches to drive)

74-38204-02

RZ56 bracket, left (attaches to drive)

74-38204-01

RZ56 shock mount, right (attaches to enclosure)

70-25452-05

RZ56 shock mount, left (attaches to enclosure)

70-25452-06

TK70 bracket, right (attaches to drive)

74-33573-01

TK70 bracket, left (attaches to drive)

74-33573-02

TK70 shock mount, right (attaches to enclosure)

70-23997-01

TK70 shock mount, left (attaches to enclosure)

70-23997-02

B.2 Hardware Option Kits
Table B–2 Hardware Option Kits
Item

Field Number

Factory Number

CPU module, dual (L2001)

KA60-AA

N/A

CPU module, dual (L2010)

KA60-BA

N/A

CXY08 asynchronous interface
module

CXY08-AF

CXY08-AA

DSV11 synchronous I/O interface
module

DSV11-SF

DSV11-SA

DWFQA Q-bus adapter (L2002)

DWFQA-AF

DWFQA-AA

Graphics expansion module
(L2006), 16 planes

VCB03-AF

VCB03-AA

Memory module, 8 Mbytes
(L2007-AA)

MS60-AA

Memory module, 16 Mbytes
(L2007-BA)

MS60-BA

Memory module, 32 Mbytes
(L2007-CA)

MS60-CA

Part Numbers B–5

Table B–2 (Cont.) Hardware Option Kits
Item

Field Number

Factory Number

RRD40 optical compact disc
drive, 635 Mbytes (includes drive,
expansion box, cable, U.S. power
cord)

RRD40-GA

RZ55 hard disk drive, 332 Mbytes
(includes drive, brackets, mounts,
screws)

RZ55A-SF

RZ55A-SA

RZ56 hard disk drive, 665 Mbytes
(includes drive, brackets, mounts,
screws)

RZ56-SF

RZ56-SA

TK70 tape drive, 296 Mbytes
(includes drive, controller, adapter
module, brackets, mounts, screws)

VS60B-AF

VS60B-AA

TS05 tape drive, 40.5 Mbytes
(includes drive, TSV05 controller,
H9642 cabinet)

TSV05-SE/SF

TSV05-SE/SF3

3 TSV05-SE is for 110 V; TSV05-SF is for 240 V

B.3 Documentation
You can order the following documents from Digital:
Table B–3 Hardware Documentation
Item

Part Number

VAXstation 3520/3540 Workstation
VAXstation 3520/3540 Release Notes

EK-313AA-RN-001

VAXstation 3520/3540 Hardware Installation
Guide

EK-250AA-IN-001

VAXstation 3520/3540 Operator’s Guide

EK-251AA-UG-001

VAXstation 3520/3540 Maintenance Guide

EK-258AA-MG-001

VS60S System Illustrated Parts Breakdown

EK-VS60S-IP-001

B–6 Part Numbers

Table B–3 (Cont.) Hardware Documentation
Item

Part Number

VAXstation 3820/3840 Workstation
VAXstation 3820/3840 Release Notes

EK-381AA-RN-001

VAXstation 3820/3840 Hardware Installation
Guide

EK-380AA-IN-001

VAXstation 3820/3840 Owner’s Manual

EK-379AA-OP-001

VAXstation 3520/3540 and 3820/3840
Maintenance Guide

EK-258AA-MG-003

VS60S System Illustrated Parts Breakdown

EK-VS60S-IP-001

VAXstation 3520/3540 and 3820/3840 Components and Add-Ons
CXY08 Technical Manual

EK-CXY08-TM

DSV11 User Guide

EK-DSV11-UG

Mouse Installation Instructions

EK-VSXXA-IN

RZ55 Disk Drive Service Manual

EK-RZ55D-SV

RZ56 Disk Drive Service Manual

EK-RZ56D-SV

RRD40 Owner’s Manual

EK-RRD40-OM-001

Tablet Installation Instructions

EK-VSXXB-IN

TK70 Tape Drive Installation Guide

EK-TK70E-IN-001

TK70 Streaming Tape Drive Owner’s Manual

EK-OTK70-OM-001

TSV05 User Guide

EK-TSV05-UG

VR295 Monitor Installation Guide

EK-VR295-IN-001

VR295 Monitor Pocket Service Guide

EK-VR29X-PS-001

Workstations Network Guide

EK-VS315-GD-001

Part Numbers B–7

Table B–4 Software Documentation
Item

Part Number

ULTRIX-32 Systems
ULTRIX-32 Worksystem User Kit

QA-VV1AD-GZ

ULTRIX-32 Worksystem Programming Kit

QA-VV1AE-GZ

ULTRIX-32 Worksystem Full Kit

QA-VV1AA-GZ

VMS Systems
VMS Base Set

QA-095AA-GZ-5.0

VMS Extended Set

QA-001AA-GZ-5.0

VMS General User Subkit

QA-001A1-GZ-5.0

VMS Programming Subkit

QA-001A3-GZ-5.0

VMS System Management Subkit

QA-001A2-GZ-5.0

B–8 Part Numbers

B.4 Ordering Information
Customers can order documentation by phone or mail.
Continental USA and Puerto Rico
Call 800-258-1710 or mail to:
Digital Equipment Corporation
P.O. Box CS2008
Nashua, NH 03061
New Hampshire, Alaska, and Hawaii
Call 1-603-884-6660.
Outside the USA and Puerto Rico
Mail to:
Digital Equipment Corporation
Attn: Accessories and Supplies Business Manager c/o Local Subsidiary or
Digital-Approved Distributor
Digital personnel may order documents from:
Digital Equipment Corporation
444 Whitney Street
Northboro, MA 01532
Attn: Publishing and Circulation Services (NRO3/W3)
Order Processing Section

C
Console Commands
The VAXstation operates in two modes, program I/O mode and console I/O
mode.
•

Program I/O mode is the normal operating mode, where the operator
interacts with the terminal.

•

Console I/O mode is used to perform such functions as bootstrapping
and diagnostic testing. This mode allows the user to control the
processor and the console terminal.

This appendix explains
•

How to use console commands

•

The syntax and function of each console command

C.1 Overview
To enter console mode: The system automatically enters console mode
whenever you start your VAXstation and whenever the processor halts.
You can enter console mode by pressing the Halt button on the system unit
control panel or by pressing the Break key on an alternate terminal. You
can also use the SET HALT console command to program the processor to
enter console mode automatically in the event of a restart or a failed boot.
To exit console mode: Enter the BOOT, CONTINUE, or START console
command, or press the Restart/Run button on the system unit control
panel.
When the system is in console I/O mode: The screen displays the
prompt CPU processor-id >>>, where processor-id is a digit and a letter
identifying the processor handling the command. When the console
prompt appears, you can enter console commands.

C–1

C–2 Console Commands

C.1.1 Conventions Used in This Appendix
Console commands presented in this appendix follow these conventions:
device-name

Parameters shown in italics are placeholders that you
replace with an actual value.

/MEMORY | /RPB

When parameters in a series are separated by vertical
lines, you may specify one and only one parameter from
the group.

[/A]

Parameters enclosed in brackets are optional. You do
not need to specify them for the command to be valid.

Ctrl C

For Ctrl key sequences, press and hold Ctrl while
pressing the other key.

C.1.2 Rules for Entering Console Commands
•

The console program accepts commands up to 80 characters long, not
including deleted characters or the terminating carriage return. If
you try to enter a longer command, an error message appears.

•

You can abbreviate most commands and arguments. You can enter
most commands by typing just the first letter of the command
keyword. Acceptable abbreviations are listed along with the
commands in this appendix.

•

The console program treats multiple adjacent spaces and tabs as a
single space. The program ignores leading and trailing spaces and
tabs.

•

All numbers (addresses, counts, data) are in hexidecimal format,
except for symbolic register names, which are in decimal format.

•

Console commands are not case sensitive. You can enter commands in
uppercase or lowercase characters.

•

In console mode, certain keys have special functions. These keys are
listed in Table C–1.

Console Commands C–3

Table C–1 Keys with Special Functions in Console Mode
Key

Function

Break

Halts the processor and activates console mode.

Return

Sends the command on the command line to the console
program for execution.

Deletes the character to the left of the cursor on the command
line. On video terminals, the deleted character disappears
from the screen. On hardcopy terminals, deleted characters are
echoed to the screen between backslashes. The console program
assumes that unknown attached console devices are hardcopy
terminals.

Delete

Ctrl C

Aborts the current command and displays the console prompt
on the next line. The console terminal echoes ^C.

Ctrl O

Disables output to the console device until the next Ctrl O is
entered. (Pressing Break or Ctrl C also reenables output.) The
console terminal echoes ^O when this key press disables output
but not when it reenables output. To indicate that the console
program is again accepting transmissions, the terminal prints
an error message or displays the console prompt.

Ctrl P

Terminates the Z command. The console terminal echoes ^P.

Ctrl Q

Resumes output to the console terminal after a Ctrl S sequence.
The console terminal does not echo this key press. Ctrl Q is
equivalent to XON.

Ctrl R

Retypes the current line, eliminating all deleted characters.

Ctrl S

Stops output to the console terminal until Ctrl Q is typed.
(Pressing Ctrl C , Ctrl O , or Break also clears Ctrl S .) The
console terminal does not echo this key sequence. Ctrl S is
equivalent to XOFF.

Ctrl U

Deletes the current command line and displays the console
prompt on the next line. The console terminal echoes ^U.
Pressing Ctrl U while a command is executing does not abort
the command.

C–4 Console Commands
BOOT

C.2 Console Commands
Three types of console commands are available:
Processor-control commands

BOOT
CONTINUE
HALT
INITIALIZE
START
UNJAM

Data-transfer commands

EXAMINE
DEPOSIT
TRANSFER

Console-control commands

! (comment)
REPEAT
SET
SHOW
TEST
Z

The following sections describe these commands in detail in alphabetical
order.

BOOT
The BOOT command transfers control to the virtual machine boot (VMB)
program, which loads and starts the operating system.

Format
B [/R5:data] [device-name]

/R5:data
Specify /R5:data to pass a parameter to the VMB. The console program
loads register 5 with the specified data after initializing the system and
before starting the VMB.
device-name
The VMB boots the operating sytem from the device specified in devicename. The device name is generally specified in the form LLLn, where
the first three characters are letters and n is from one to three digits. You
can optionally include a colon at the end of the device name.

Console Commands
CONTINUE

C–5

Device names for the VAXstation 3520/3540 workstation are listed here.
DKA000 (SCSI disk)
DKA100 (SCSI disk)
DKA200 (SCSI disk)
DKA300 (SCSI disk)
DKA400 (SCSI disk)
DKA500 (SCSI disk)
DKA600 (SCSI disk)
DKA700 (SCSI disk)
ESA0 (Ethernet network)
MUA0 (Tape drive on Q-bus)
If you do not specify a device name, the system boots from the device
specified by the last SET BOOT command. If no device has been specified,
the boot operation fails.

COMMENT
The COMMENT command is used to annotate console I/O command
sequences. It is ignored by the console program.

Format
! comment

comment
For comment, specify text of up to 80 characters per line, not including
the terminating return character.

CONTINUE
When you enter the CONTINUE command, the console switches to
program I/O mode, and the processor begins execution at the address
currently in the program counter. The processor is not reinitialized.

C–6 Console Commands
DEPOSIT

Format
C [/A] [processor-id]

/A
Specify /A to resume execution of all enabled halted processors.
processor-id
Specify processor-id to resume execution of a particular processor. If you
do not specify a processor name, the current processor resumes execution.

DEPOSIT
The DEPOSIT command sets the specified data at the specified address.
You can optionally specify one or more address or data qualifiers. If you
do not specify any qualifiers, the system uses the address space and data
size used in the last DEPOSIT or EXAMINE command. At processor
initialization, the default address space is physical memory, the default
address is 0, and the default data size is a longword.

Format
D [data-size] [address-space] [/U] [/N:count] address data

data-size
For data-size, specify one of the following:
/B

Sets the data size to a byte.

Sets the data size to a word (two bytes).

Sets the data size to a longword (four bytes).

address-space
For address-space, specify one of the following:
/V

Sets the address space to virtual memory. If memory mapping is not
enabled, virtual addresses are equal to physical addresses.

Sets the address space to physical memory.

Sets the address space to the internal processor registers.

Sets the address space to the general registers (R0 through R15).

Console Commands
DEPOSIT

C–7

/U
Specify /U to permit write access to console program memory and to
disable virtual address protection checking.
/N
Specify /N:count to indicate that the specified address is the beginning of
an address range. The console program deposits the specified data at the
first address and then at the number of succeeding addresses specified by
count.
The succeeding addresses are always larger than the specified address,
even when the specified address is the symbolic address ‘‘-.’’ (For repeated
references to preceding addresses, enter the command REPEAT DEPOSIT
data.)

address
For address, specify any valid address. You can also specify one of the
following symbolic addresses:
PSL

The processor status longword sets the address space to M
(machine-dependent). Do not specify any address qualifiers
with PSL.

The program counter (general register 15) sets the address
space to G.

The stack pointer (general register 14) sets the address space
to G.

Sets the address space to G and the address to general
register n. Specify n as a decimal integer. For example:
D R5 1234 is equivalent to D/G 5 1234
D R10 6FF00 is equivalent to D/G A 6FF00

Plus sign (+)

Sets the address to the location immediately following
the last location referenced in a DEPOSIT or EXAMINE
command. In references to physical or virtual memory
spaces, address becomes the last address plus the data size
of the last reference (+1 for a byte, +2 for a word, +4 for a
longword). For other address spaces, the address is the last
address plus 1.

C–8 Console Commands
EXAMINE

Minus sign (-)

Sets the address to the location immediately preceding
the last location referenced in a DEPOSIT or EXAMINE
command. In references to physical or virtual memory
spaces, address becomes the last address minus the data
size of the last reference (-1 for a byte, -2 for a word, -4 for a
longword). For other address spaces, the address is the last
address minus 1.

Asterisk (*)

Sets the address to the last location referenced by an
EXAMINE or DEPOSIT command.

At sign (@)

Causes the contents of the last location referenced by an
EXAMINE or DEPOSIT command to become address for the
current command.

data
For data, specify a hexidecimal value. If the specified data is too large
for the specified data size, the console program ignores the command and
issues an error message. If the specified data is smaller than the specified
data size, the data is extended on the left with 0s.

EXAMINE
Use the EXAMINE command to examine the contents of memory at the
specified address.
All arguments to the E command are optional.

Format
E [data-size] [address-space] [/U] [/N:count] [address]
The console program response to this command appears in the following
format:
address-space-identifier address data
The address space identifier will be one of the following:
P

Physical memory. Note that when virtual memory is examined, the
address space and address in the response are the translated physical
address.

General register.

Internal processor register.

Console Commands
EXAMINE

C–9

Machine-dependent. Used only in PSL display.

Data-size
Defaults to the last values specified in a DEPOSIT or EXAMINE
command.
For data-size, specify one of the following:
/B

Sets the data size to byte.

Sets the data size to word (two bytes).

Sets the data size to longword (four bytes).

address-space
Defaults to the last values specified in a DEPOSIT or EXAMINE
command.
For address-space, specify one of the following:
/V

Sets the address space to virtual memory. If memory mapping is not
enabled, virtual addresses are equal to physical addresses.

Sets the address space to physical memory.

Sets the address space to internal processor registers.

Sets address space to the general registers (R0 through R15).

/U
Specify /U to permit write access to console program memory and to
disable virtual address protection checking.
/N
Specify /N:count to indicate that the specified address is the beginning of
an address range. The console program examines the specified data at the
first address and then at the number of succeeding addresses specified by
count.
The succeeding addresses always are larger than the specified address,
even when the specified address is the symbolic address ‘‘-.’’ (For
repeated references to preceding addresses, enter the command REPEAT
EXAMINE data.)

Address
Defaults to a plus sign (+).

C–10 Console Commands
EXAMINE

For address specify any valid address. You can also specify one of the
following symbolic addresses:
PSL

The processor status longword sets the address space to
M. Do not specify any address qualifiers with PSL.

The program counter (general register 15) sets the
address space to G.

The stack pointer (general register 14) sets the address
space to G.

Sets the address space to /G and the address to general
register n. Specify n as a decimal integer. For example:
E R5 1234 is equivalent to E/G 5 1234 E R10 6FF00 is
equivalent to E/G A 6FF00

Plus sign (+)

Sets the address to the location immediately following
the last location referenced in a DEPOSIT or EXAMINE
command. In references to physical or virtual memory
spaces, the location referenced is the last address plus
the size of the last reference (+1 for a byte, +2 for a
word, +4 for a longword). For other address spaces, the
address is the last address referenced plus 1.

Minus sign (-)

Sets the address to the location immediately preceding
the last location referenced in a DEPOSIT or EXAMINE
command. In references to physical or virtual memory
spaces, the location referenced is the last address minus
the size of the last reference (-1 for a byte, -2 for a word,
-4 for a longword). For other address spaces, the address
is the last address referenced minus 1.

Asterisk (*)

Sets the address to the last location referenced by an
EXAMINE or DEPOSIT command.

At sign (@)

Causes the contents of the last location referenced by an
EXAMINE or DEPOSIT command to become address for
the current command.

Console Commands
INITIALIZE

C–11

HALT
Specify HALT to halt the specified processor. If you do not specify a
processor number, the console program halts all processors.

Format
H [processor-id]

processor-id
Specify processor-id to indicate the processor you want to halt.

INITIALIZE
The INITIALIZE command initializes the current processor. The
command sets the address location to physical memory, the data size
to longword, and the address to 0, and it disables the cache. INITIALIZE
also sets the registers listed in Table C–2.

Format
Table C–2 Default Register Values
Register

Value

PSL

041F0000

IPL

ASTLVL

SISR

ICCS

Clears bits 6 and 0; the rest are unpredictable.

RXCS

TXCS

MAPEN

C–12 Console Commands
SET

REPEAT
Specify REPEAT to repeatedly display and execute the specified command.
To stop the repetition, press Ctrl C . To pause the repetition, press Ctrl S ,
then use Ctrl Q to continue.

Format
R command

command
For command, specify any valid console command except REPEAT.

SET
Use SET to define console program parameters.

BOOT device-name
Specify BOOT device-name to set the default boot device. For the optional
device-name parameter, specify a valid device name as specified in the
BOOT command. If you do not specify a device name, the program clears
the default boot device name.
BFLG value
Specify BFLG value to set the default boot flags. For value, specify a
hexidecimal number of up to eight digits.

Console Commands
SET

C–13

HALT value
Specify HALT value to set the processor halt code. This code determines
the default action the console program takes when the processor halts
for errors and at system startup. The program stores this default code
in nonvolatile RAM, so it is not lost across power cycles. If power to
nonvolatile RAM is lost, the program initializes this value to 3.
For value, specify one of the codes in Table C–3.
Table C–3 Halt Codes
Code

Description

Restart processor. If restart fails, reboot. If reboot fails, halt.

Restart processor. If restart fails, halt.

Reboot processor. If reboot fails, halt.

Halt.

LNG value
Specify LNG value to change the console language. For value, specify one
of the codes in Table C–4.
Table C–4 Language Codes
Code

Language

No setting

Danish

German

English

Spanish

French

Italian

Dutch

Finnish

Norwegian

Swedish

Portuguese

C–14 Console Commands
SET

KBD value
Specify KBD value to set the console keyboard type for the language
you are using. For value, specify one of the codes in Table C–5. This
parameter is effective only for a workstation using a separate LK201
keyboard.
Table C–5 Keyboard Type Codes
Code

Type

American/Canadian (English)

Flemish

Canadian (French)

Danish

British

Finnish

Austrian/German

Italian

Swiss (French)

Swiss (German)

Swedish

Norwegian

French/Belgian

Spanish

Portuguese

CPU processor-id ENABLE
Specify CPU processor-id ENABLE to set the enable flag of the processor
specified by processor-id. This processor operates normally.
CPU processor-id DISABLE
Specify CPU processor-id DISABLE to clear the enable flag of the
processor specified by processor-id. This processor is excluded from
normal use.

Console Commands
SET

C–15

CPU processor-id PRIMARY ENABLE
Specify CPU processor-id PRIMARY ENABLE to set the primary
processor enable flag of the processor specified by processor-id. During
startup, this processor is eligible to compete with other processors to act
as the system’s primary processor.
CPU processor-id PRIMARY DISABLE
Specify CPU processor-id PRIMARY DISABLE to clear the primary
processor enable flag of the processor specified by processor-id. During
startup, this processor is ineligible to compete with other processors to act
as the system’s primary processor.
MOP value
Specify MOP value to set the maintenance operation protocol (MOP)
network listener control field. For value specify one of the codes in
Table C–6.
Table C–6 MOP Network Listener Control Codes
Code

Description

Network listener disabled.

Network listener enabled, currently inactive.

Network listener disabled.

Network listener will become active in console.
I/O mode after 30 seconds of user inactivity.

SCSI value
Specify SCSI value to set the default small computer systems interface
(SCSI) identifier. For value specify a valid SCSI identifier.
XTIM value
Specify XTIM value to change the default timeout interval for data
transfer between the console program and automatic systems. For value,
specify the timeout interval in seconds. If you do not specify XTIM, the
console program uses a timeout interval of 10 seconds.

C–16 Console Commands
SHOW

SHOW
Specify SHOW to display the value of console program parameters.

BOOT
Specify BOOT to display the default boot device. If no default device is
set, the screen displays a blank.
BFLG
Specify BFLG to display the default boot flags. If no default flags are set,
the screen displays 0.
HALT
Specify HALT to display the default halt action codes.
LNG
Specify LNG to display the default console language. The possible values
are shown in Table C–4.
KBD
Specify KBD to display the console keyboard type. The possible values
are shown in Table C–5. If the console is not a workstation, the screen
displays a blank.
ETHER
Specify ETHER to display the Ethernet hardware address. If the system
is using multiple Ethernet devices, the screen displays the hardware
address for each device. The screen also displays the virtual machine
boot (VMB) device name for each Ethernet device. If the system is not
connected to Ethernet, the screen displays a blank.
MEM
Specify MEM to display the total memory size and the address of the first
contiguous 256-Kbyte block of good memory. MEM also displays a list
of all unavailable pages (zero entries in the bitmap). The format for the
MEM parameter display is as follows:

Console Commands
SHOW

Total size of available memory

Beginning of the 256-Kbyte block of memory

b1:e1

Beginning and ending limits of hole 1 in good memory

b2:e2

Beginning and ending limits of hole 2 in good memory

C–17

.
.
.
bn:en

Beginning and ending limits of up to as many holes as there are in
good memory

CPU processor-id
Specify CPU processor-id to display the status of the enable and primary
enable flags for the processor specified by processor-id. The format for
the CPU parameter display is En, Pn, where E stands for enable flag, P
stands for primary enable flag, and n is 0 (for disabled) or 1 (for enabled).
MOP
Specify MOP to display the current value in the MOP network listener
control field.
SCSI
Specify SCSI to display the SCSI bus configuration. The following is an
example of the resulting display.
ADDR
----5.1.0
5.7

VMB
-----DKA100

DEVTYP
-----DISK
HOST

DEVNAM
------RZ55
SII-A

NUMBYTS
------332 MB

REV
---0100

CHAR
----

•

The ADDR column shows the device address in the form moduleid.device-number.logical-unit-number for each device except the
controlling SII chip. The address for this chip is in the form moduleid.device-id.

•

The VMB column shows the device name to use when designating this
as the boot device.

•

The DEVTYP column shows what type of device this is.

•

The DEVNAM column further specifies the type.

•

The NUMBYTS column gives the capacity of the device to three
significant digits.

C–18 Console Commands
TEST

•

The REV column shows the revision number, where applicable.

•

The CHAR column shows device characteristics such as removable
media (RM) or write-protected (WP).

XTIM
Specify XTIM to display the current value of the timeout interval (in
seconds) for data transer between the console program and automatic
systems.

START
Specify START to start instruction execution at the specified address.
The START command is equivalent to a DEPOSIT command with PC
specified, followed by a CONTINUE command.

Format
S [address]

address
Specify address to start execution at a particular location. If you do
not specify an address, execution starts at the location indicated by the
current program counter.

TEST
The TEST command invokes diagnostic tests and displays the test results.

Format
T 50 [module-id] | module-id [device-number]

T 50
Specify T 50 to see all the modules in your system. From this list you
can take the module-id number to use as an optional argument. T 50
module-id shows the devices on the given module.

Console Commands
Z

C–19

T module-id, T module-id device-number
Specify T module-id or T module-id device-number to test an individual
module or device.

UNJAM
Specify UNJAM to reset all modules. For some modules, this command
has no effect.

Format

Z
Specify the Z command to send characters typed at the console terminal
to the console of the specified processor. Typed characters are echoed back
to the console terminal.

Format
Z processor-id

processor-id
For processor-id, specify the destination processor. You can specify only
one destination processor at a time; multiprocessor forwarding is not
allowed.
To terminate the Z command and return control to the console terminal,
press Ctrl P .
To send Ctrl P or an escape character to the destination processor, you
must precede the character with an escape character, entering it as a
literal.

D
Cable and Connector Pin Assignments
This appendix lists pin assignments for the following cables and
connectors in the VAXstation 3520/3540 and VAXstation 3820/3840
workstations:
•

I/O cover ribbon cable

•

I/O cover SCSI cable

•

I/O cover module external connectors

•

M-bus, Q-bus, and graphics bus connectors

•

System slot and backplane connectors

•

Power connector

•

Control panel connector

•

Loopback connectors

D–1

D–2 Cable and Connector Pin Assignments

Table D–1 I/O Cover Ribbon Cable Pin Assignments
Pin

Signal

+12 V

GND

TX0

RX0

CTS2

GND

RTS

DTR2

TX1

RX1

DSR2

GND

RI2

CD2

TX2

RX2

DSRS2

GND

SPDMI2

TMI2

TX3

RX3

+5 V

+5 VBAT

LLPBK2

GND

–12 V

MFMD0

MFMD1

LED0

LED1

LED2

LED3

TX+

TX–

LED4

SPARE

COL+

COL–

GND

RX+

RX–

GND

+12 V

Cable and Connector Pin Assignments

Table D–2 I/O Cover SCSI Cable Pin Assignments
Pin

Signal

GND

REQ

GND

SEL

GND

MSG

GND

RST

GND

ACK

GND

BSY

GND

ATN

GND

TERMPWR

<NC>

GND

PARITY

GND

DATA<7>

GND

DATA<6>

GND

DATA<5>

GND

DATA<4>

GND

DATA<3>

GND

DATA<2>

GND

DATA<1>

GND

DATA<0>

GND

D–3

D–4 Cable and Connector Pin Assignments

Table D–3 Keyboard and Mouse/Tablet Connector (I/O Cover)
Pin Assignments
Pin

Source

Signal

Description

GND

Keyboard ground

L2003

kTX0

Keyboard transmitted data

KEYBRD

kRX0

Keyboard received data

L2003

+12 V

Keyboard power

MONORTN

Monochrome video return

5
6

MOUSE

nRX1

Mouse received data

L2003

nTX1

Mouse transmitted data

GND

Mouse ground

GND

Keyboard power return

MFMD1

Manufacturing mode input

MONO

Monochrome video data

MFMD0

Manufacturing mode input

L2003

12
13

L2003

+5.3 V

Mouse power

L2003

–10 V

Mouse power

GND

Mouse power return

Table D–4 Communications Connector (I/O) Pin Assignments
Pin

Source

Signal

CCITT3

EIA†

Description

GND

101

Protective ground

L2003

CTX2

103

Modem transmitted
data

MODEM

CRX2

104

Modem received data

L2003

CRTS2

105

Request to send

MODEM

CCTS2

106

Clear to send

MODEM

CDSR2

107

Data set ready

3 Comite Consultatif International telegraphique et Telephonique. An international
consultative committee that sets international communications usage standards.

†Electronic Industries Association.

Cable and Connector Pin Assignments

D–5

Table D–4 (Cont.) Communications Connector (I/O) Pin Assignments
Pin

Source

7
8

MODEM

Signal

CCITT3

EIA†

Description

GND

102

Signal ground

CCD2

109

Carrier detector

Unconnected

MODEM

SPDMI2

112

Speed-mode
indicator

Unconnected

L2003

CLLPBK2

141

Local loopback

19
20

Unconnected
L2003

CDTR2

108/2

Data terminal ready
Unconnected

MODEM

CRI2

125

Ring indicator

L2003

CDSRS2

111

Data signaling rate
select

24
25

Unconnected
MODEM

CTMI2

142

Test-mode indicator

3 Comite Consultatif International telegraphique et Telephonique. An international
consultative committee that sets international communications usage standards.

†Electronic Industries Association.

D–6 Cable and Connector Pin Assignments

Table D–5 Printer/Console Connector (I/O) Pin Assignments
Pin

Source

Signal

Description

L2003

PCO

Control output

L2003

PTX3

Printer/console transmitted data

L2003

GND

Transmission ground

PRNTR

GND

Reception ground

PRNTR

PRX3

Printer/console received data

PRNTR

PCI

Control input

Table D–6 ThickWire Ethernet Connector (I/O) Pin Assignments
Pin

Source

Signal

Description
Shield

XCVR

ACOL+

Collision presence

L2003

ATX+

Transmission

GND

Ground

4
5

XCVR

ARX+

Reception

XCVR

GND

Power return

CTL+

Control output

GND

Ground

XCVR

ACOL–

Collision presence

L2003

ATX–

Transmission

GND

Ground

11
12

XCVR

ARX–

Reception

L2003

+12 V

Power

GND

Ground

CTL–

Control output

Cable and Connector Pin Assignments

Table D–7 Buses for Slots 1–9
Slot

Buses on

Pins A1–A94

Pins B1–B94

VI-bus

M-bus

(reserved)

M-bus

(reserved)

J10

M-bus

J11

(reserved)

J12

M-bus

J13

(reserved)

J14

M-bus

J15

(reserved)

J16

M-bus

J17

Q-bus

J18

M-bus

Table D–8 Buses for Slots 10–12
Buses on J19,

Buses on J20,

Slot

J21, J23

J22, J24

Q22-bus

Table D–9 Module IDs
Slot

MID2, MID1, MID0

Not applicable

111 (7)

101 (5)

100 (4)

011 (3)

010 (2)

D–7

D–8 Cable and Connector Pin Assignments

Table D–9 (Cont.) Module IDs
Slot

MID2, MID1, MID0

001 (1)

000 (0)

Not applicable

Table D–10 M-Bus Backplane Pin Assignments
(Slots 3–9, Connector B)
Pin

Signal

GND

BATTERY5V

MCLKA

GND

+5 V

MCLKB

GND

B10

+12 V

B11

+12 V

B12

+12 V

B13

MBRQ L

B14

GND

B15

MBRM0 L

B16

MBRM1 L

B17

+5 V

B18

MBRM2 L

B19

MBRM3 L

B20

MBRM4 L

B21

MBRM5 L

B22

GND

B23

MBRM6 L

B24

MSPAR

B25

GND

B26

MSTAT0

B27

MSTAT1

B28

MIRQ0 L

B29

MIRQ1 L

B30

+5 V

B31

MIRQ2 L

B32

MIRQ3 L

B33

GND

B34

MCPAR

B35

MCMD0

B36

MCMD1

Cable and Connector Pin Assignments

Table D–10 (Cont.) M-Bus Backplane Pin Assignments
(Slots 3–9, Connector B)
Pin

Signal

B37

MCMD2

B38

GND

B39

MCMD3

B40

MRSVB40

B41

+5 V

B42

MSLOT

B43

MDPAR

B44

MID0

B45

MID1

B46

GND

B47

MID2

B48

MCLKI

B49

GND

B50

GND

B51

MDAL00

B52

MDAL01

B53

MDAL02

B54

+5 V

B55

MDAL03

B56

MDAL04

B57

GND

B58

MDAL05

B59

MDAL06

B60

MDAL07

B61

MRESET L

B62

GND

B63

MDAL08

B64

MDAL09

B65

+5 V

B66

MDAL10

B67

MDAL11

B68

MDAL12

B69

MDAL13

B70

GND

B71

MDAL14

B72

MDAL15

B73

GND

B74

MDAL16

B75

MDAL17

B76

MDAL18

B77

MDAL19

B78

+5 V

B79

MDAL20

B80

MDAL21

B81

GND

B82

MDAL22

B83

MDAL23

B84

MDAL24

B85

MDAL25

B86

GND

B87

MDAL26

B88

MDAL27

B89

+5 V

B90

MDAL28

D–9

D–10 Cable and Connector Pin Assignments

Table D–10 (Cont.) M-Bus Backplane Pin Assignments
(Slots 3–9, Connector B)
Pin

Signal

B91

MDAL29

B92

MDAL30

B93

MDAL31

B94

GND

Table D–11 M-Bus Backplane Pin Assignments
(Slots 4–8, Connector A)
Pin

Signal

GND

Not used

+5 V

Not used

GND

A10

Not used

A11

Not used

A12

Not used

A13

Not used

A14

GND

A15

Not used

A16

Not used

A17

+5 V

A18

Not used

A19

Not used

A20

Not used

A21

Not used

A22

GND

A23

Not used

A24

Not used

A25

GND

A26

Not used

A27

Not used

A28

Not used

A29

Not used

A30

+5 V

A31

Not used

A32

Not used

A33

GND

A35

Not used

A36

Not used

A37

Not used

A38

GND

A39

Not used

A40

Not used

A41

+5 V

A42

Not used

A34

Cable and Connector Pin Assignments D–11

Table D–11 (Cont.) M-Bus Backplane Pin Assignments
(Slots 4–8, Connector A)
Pin

Signal

A43

Not used

A44

Not used

A45

Not used

A46

GND

A47

Not used

A48

Not used

A49

GND

A50

Not used

A51

Not used

A52

Not used

A53

Not used

A54

+5 V

A55

Not used

A56

Not used

A57

GND

A58

Not used

A59

Not used

A60

Not used

A61

Not used

A62

GND

A63

Not used

A64

Not used

A65

+5 V

A66

Not used

A67

Not used

A68

Not used

A69

Not used

A70

GND

A71

Not used

A72

Not used

A73

GND

A74

Not used

A75

Not used

A76

Not used

A77

Not used

A78

+5 V

A79

–12 V

A80

–12 V

A81

GND

A82

MRUN L

A83

MRSVA83

A84

MRSVA84

A85

MDATINV L

A86

GND

A87

MBUSY L

A88

MSHARED L

A89

+5 V

A90

MABORT L

A91

BHALT L

A92

MDCOK

A93

MPOK

A94

GND

D–12 Cable and Connector Pin Assignments

Table D–12 M-Bus MBRQ Connection per Slot
Slot

B13

B15

B13

B16

B13

B18

B13

B19

B13

B20

B13

B21

B13

B23

B13

M-bus
MBRQ

Table D–13 Q-Bus Slot Priority
Priority

Slot

Highest

10 (J19)
11 (J21)
12 (J23)
12 (J24)
11 (J22)

Lowest

10 (J20)

Table D–14 Q-Bus Backplane Pin Assignments
(Slots 10–12, Connector A)
Column 1

Row

Column 2

BIRQ5

+5 V

BIRQ6

Not used

BDAL16

GND

BDAL17

+12 V

Cable and Connector Pin Assignments D–13

Table D–14 (Cont.) Q-Bus Backplane Pin Assignments
(Slots 10–12, Connector A)
Column 1

Row

Column 2

SSPARE1

BDOUT

SSPARE2

BRPLY

SSPARE3

BDIN

GND

BSYNC

MSPAREA

BWTBT

MSPAREA

BIRQ4

GND

BIAKI

BDMR

BIAKO

BHALT

BBS7

BREF

BDMGI

Not used

BDMGO

GND

BINIT

PSPARE1

BDAL00

Not used

BDAL01

Table D–15 Q-Bus Backplane Pin Assignments
(Slots 10–12, Connector B)
Column 1

Row

Column 2

BDCOK

+5 V

BPOK

Not Used

BDAL18

GND

BDAL19

+12 V

BDAL20

BDAL02

BDAL21

BDAL03

SSPARE8

BDAL04

GND

BDAL05

MSPAREB

BDAL06

D–14 Cable and Connector Pin Assignments

Table D–15 (Cont.) Q-Bus Backplane Pin Assignments
(Slots 10–12, Connector B)
Column 1

Row

Column 2

MSPAREB

BDAL07

GND

BDAL08

BSACK

BDAL09

BIRQ7

BDAL10

BEVENT

BDAL11

Not used

BDAL12

GND

BDAL13

PSPARE2

+5 V

BDAL15

Table D–16 Q-Bus Backplane Pin Assignments
(Slot 9, Connector A)
Pin

Signal

GND

BIRQ5

Not used

BIRQ6

Not used

+5 V

BDAL16

Not used

GND

A10

BDAL17

A11

Not used

A12

BDOUT

A13

Not used

A14

GND

A15

BRPLY

A16

Not used

A17

+5 V

A18

BDIN

A19

Not used

A20

BSYNC

A21

Not used

A22

GND

A23

BWTBT

A24

Not used

A25

GND

A26

BIRQ4

A27

Not used

A28

BIAK01

Cable and Connector Pin Assignments D–15

Table D–16 (Cont.) Q-Bus Backplane Pin Assignments
(Slot 9, Connector A)
Pin

Signal

A29

BDMR

A30

+5 V

A31

BBS7

A32

BREF

A33

GND

A34

BDMGO1

A35

BINIT

A36

BDAL00

A37

BDAL01

A38

GND

A39

Not used

A40

Not used

A41

+5 V

A42

BDAL18

A43

BDAL19

A44

BDAL20

A45

BDAL02

A46

GND

A47

BDAL21

A48

BDAL03

A49

GND

A50

BDAL04

A51

BDAL05

A52

Not used

A53

BDAL06

A54

+5 V

A55

BDAL07

A56

Not used

A57

GND

A58

BDAL08

A59

BSACK

A60

BDAL09

A61

Not used

A62

GND

A63

BIRQ7

A64

Not used

A65

+5 V

A66

BDAL10

A67

BEVENT

A68

BDAL11

A69

Not used

A70

GND

A71

BDAL12

A72

BDAL13

A73

GND

A74

BDAL14

A75

Not used

A76

BDAL15

A77

Not used

A78

+5 V

A79

–12 V

A78

–12 V

A81

GND

A82

MRUN L

D–16 Cable and Connector Pin Assignments

Table D–16 (Cont.) Q-Bus Backplane Pin Assignments
(Slot 9, Connector A)
Pin

Signal

A83

MRSVA83

A84

MRSVA84

A85

MDATINV L

A86

GND

A87

MBUSY L

A88

MSHARED L

A89

+5 V

A90

MABORT L

A91

BHALT L

A92

BDCOK

A93

BPOK

A94

GND

Table D–17 Graphics Backplane Pin Assignments
(Slot 3, Connector A)
Pin

Signal

GND

BUFVI31 H

BUFVI30 H

BUFVI29 H

BUFVI28 H

+5 VA

BUFVI27 H

BUFVI26 H

GND

A10

BUFVI25 H

A11

BUFVI24 H

A12

BUFVI23 H

A13

BUFVI22 H

A14

GND

A15

BUFVI21 H

A16

BUFVI20 H

A17

+5 VA

A18

BUFVI19 H

A19

BUFVI18 H

A20

BUFVI17 H

A21

BUFVI16 H

A22

GND

A23

BUFVI15 H

A24

BUFVI14 H

A25

GND

A26

BUFVI13 H

A27

BUFVI12 H

A28

BUFVI11 H

A29

BUFVI10 H

A30

+5 VA

A31

BUFVI09 H

A32

BUFVI08 H

A33

GND

A34

BUFVI07 H

Cable and Connector Pin Assignments D–17

Table D–17 (Cont.) Graphics Backplane Pin Assignments
(Slot 3, Connector A)
Pin

Signal

A35

BUFVI06 H

A36

BUFVI05 H

A37

BUFVI04 H

A38

GND

A39

BUFVI03 H

A40

BUFVI02 H

A41

+5 VA

A42

BUFVI01 H

A43

BUFVI00 H

A44

BUFBM3 L

A45

BUFBM2 L

A46

GND

A47

BUFBM1 L

A48

BUFBM0 L

A49

GND

A50

BUFWR L

A51

DATAS L

A52

BUFDS L

A53

GRSVA53 H

A54

+5 VA

A55

GRSVA55 H

A56

GRSVA56 H

A57

GND

A58

GRSVA58 H

A59

GRSVA59 H

A60

GRSVA60 H

A61

GRSVA61 H

A62

GND

A63

GRSVA63 H

A64

INIT L

A65

+5 VA

A66

GRSVA66 H

A67

GRSVA67 H

A68

GRSVA68 H

A69

GRSVA69 H

A70

GND

A71

Not used

A72

Not used

A73

GND

A74

Not used

A75

GRSVA75 H

A76

Not used

A77

Not used

A78

+5 VA

A79

–12 V

A80

–12 V

A81

GND

A82

MRUN L

A83

MRSVA83 H

A84

MRSVA84 H

A85

MDATINV L

A86

GND

A87

MBUSY L

A88

MSHARED L

D–18 Cable and Connector Pin Assignments

Table D–17 (Cont.) Graphics Backplane Pin Assignments
(Slot 3, Connector A)
Pin

Signal

A89

+5 VA

A90

MABORT L

A91

BHALT L

A92

MDCOK H

A93

MPOK H

A94

GND

Table D–18 Graphics Backplane Pin Assignments
(Slots 1–2, Connector A)
Pin

Signal

GND

BUFVI31 H

BUFVI30 H

BUFVI29 H

BUFVI28 H

+5 VA

BUFVI27 H

BUFVI26 H

GND

A10

BUFVI25 H

A11

BUFVI24 H

A12

BUFVI23 H

A13

BUFVI22 H

A14

GND

A15

BUFVI21 H

A16

BUFVI20 H

A17

+5 VA

A18

BUFVI19 H

A19

BUFVI18 H

A20

BUFVI17 H

A21

BUFVI16 H

A22

GND

A23

BUFVI15 H

A24

BUFVI14 H

A25

GND

A26

BUFVI13 H

A27

BUFVI12 H

A28

BUFVI11 H

A29

BUFVI10 H

A30

+5 VA

A31

BUFVI09 H

A32

BUFVI08 H

A33

GND

A34

BUFVI07 H

A35

BUFVI06 H

A36

BUFVI05 H

A37

BUFVI04 H

A38

GND

A39

BUFVI03 H

A40

BUFVI02 H

Cable and Connector Pin Assignments D–19

Table D–18 (Cont.) Graphics Backplane Pin Assignments
(Slots 1–2, Connector A)
Pin

Signal

A41

+5 VA

A42

BUFVI01 H

A43

BUFVI00 H

A44

BUFBM3 L

A45

BUFBM2 L

A46

GND

A47

BUFBM1 L

A48

BUFBM0 L

A49

GND

A50

BUFWR L

A51

DATAS L

A52

BUFDS L

A53

GRSVA53 H

A54

+5 VA

A55

GRSVA55 H

A56

GRSVA56 H

A57

GND

A58

GRSVA58 H

A59

GRSVA59 H

A60

GRSVA60 H

A61

GRSVA61 H

A62

GND

A63

GRSVA63 H

A64

INIT L

A65

+5 VA

A66

GRSVA66 H

A67

GRSVA67 H

A68

GRSVA68 H

A69

GRSVA69 H

A70

GND

A71

MX23B3 H

A72

MX23B2 H

A73

GND

A74

MX23B1 H

A75

GRSVA75 H

A76

MX23B0 H

A77

NIBCLK H

A78

+5 VA

A79

–12 V

A80

–12 V

A81

GND

A82

MX22B3 H

A83

MX22B2 H

A84

MX22B1 H

A85

CMP5 H

A86

GND

A87

CMP4 H

A88

CMP3 H

A89

+5 VA

A90

CMP2 H

A91

CMP1 H

A92

CMP0 H

A93

MPOK H

A94

GND

D–20 Cable and Connector Pin Assignments

Table D–19 Graphics Backplane Pin Assignments
(Slots 1–2, Connector B)
Pin

Signal

GND

Not used

MX22B0 H

GND

+5 VA

MX21B3 H

GND

B10

+12 VA

B11

+12 VA

B12

+12 VA

B13

MX21B2 H

B14

GND

B15

MX21B1 H

B16

MX21B0 H

B17

+5 VA

B18

MX20B3 H

B19

MX20B2 H

B20

MX20B1 H

B21

MX20B0 H

B22

GND

B23

MX19B3 H

B24

MX19B2 H

B25

GND

B26

MX19B1 H

B27

MX19B0 H

B28

MX18B3 H

B29

MX18B2 H

B30

+5 VA

B31

MX18B1 H

B32

MX18B0 H

B33

GND

B34

MX17B3 H

B35

MX17B2 H

B36

MX17B1 H

B37

MX17B0 H

B38

GND

B39

MX16B3 H

B40

MX16B2 H

B41

+5 VA

B42

VISLOT H

B43

MX16B1 H

B44

MID0

B45

MID1

B46

GND

B47

MID2

B48

MX16B0 H

B49

GND

B50

GND

B51

MX15B3 H

B52

MX15B2 H

B53

MX15B1 H

B54

+5 VA

Cable and Connector Pin Assignments D–21

Table D–19 (Cont.) Graphics Backplane Pin Assignments
(Slots 1–2, Connector B)
Pin

Signal

B55

MX15B0 H

B56

MX14B3 H

B57

GND

B58

MX14B2 H

B59

MX14B1 H

B60

MX14B0 H

B61

MRESET

B62

GND

B63

MX13B3 H

B64

MX13B2 H

B65

+5 VA

B66

MX13B1 H

B67

MX13B0 H

B68

MX12B3 H

B69

MX12B2 H

B70

GND

B71

MX12B1 H

B72

MX12B0 H

B73

GND

B74

MX11B3 H

B75

MX11B2 H

B76

MX11B1 H

B77

MX11B0 H

B78

+5 VA

B79

MX10B3 H

B80

MX10B2 H

B81

GND

B82

MX10B1 H

B83

MX10B0 H

B84

MX09B3 H

B85

MX09B2 H

B86

GND

B87

MX09B1 H

B88

MX09B0 H

B89

+5 VA

B90

MX08B3 H

B91

MX08B2 H

B92

MX08B1 H

B93

MX08B0 H

B94

GND

Table D–20 Power Connector Pin Assignments (Connector J25)
Pin

Signal

FANAPLUS

FANAMINUS

FANBPLUS

FANBMINUS

+5 VA

D–22 Cable and Connector Pin Assignments

Table D–20 (Cont.) Power Connector Pin Assignments (Connector J25)
Pin

Signal

+5 VA

GND

+12 VA

MDCOK

BEVENT L

MPOK

Cable and Connector Pin Assignments D–23

Table D–21 Fan Connector Pin Assignments (Connector J26)
Pin

Signal

FANAPLUS

No signal (used for keying)

FANAMINUS

FANBPLUS

FANBMINUS

Table D–22 DCOK Connector Pin Assignments (Connector J27)
Pin

Signal

+5 VA

BHALT L

GND

MPOK

Not used

MDCOK

MRUN L

Table D–23 Power Connector Pin Assignments (Connector J29)
Pin

Signal

Not used

+5 VB

GND

D–24 Cable and Connector Pin Assignments

Table D–23 (Cont.) Power Connector Pin Assignments (Connector J29)
Pin

Signal

GND

+12 VB

MDCOK

+12 VB

MPOK

Table D–24 Summary of Loopback Connectors
Function

Standard/Unique

Part Number

Option
Number

Printer/console
loopback

Standard

12-25083-01

H3103

Communications
loopback

New part

12-15336-13

H3200

ThickWire loopback

Standard

12-22196-02

N/A

ThinWire Tconnector

Standard

12-25869-01

H8223

ThinWire terminator

Standard

12-26318-01

H8225

Cable and Connector Pin Assignments D–25

Table D–25 Printer/Console Loopback Connector Pin Assignments
From
Pin No.

Signal

To
Pin No.

Signal

Description

P1-1

P1-6

Control loopback

P1-2

TX+

P1-5

RX+

Data loopback

P1-3

TX-

P1-4

RX-

Signal ground

Table D–26 Modem Loopback Connector Pin Assignments
From
Pin No.

Signal

To
Pin No.

Signal

P4-2

TX2

P4-3

RX2

P4-4

RTS2

P4-5

CTS2

P4-6

DSR2

P4-20

DTR2

P4-12

SPDMI2

P4-23

DSRS2

P4-18

LLPBK2

P4-8

CI2

P4-18

LLPBK2

P4-22

RI2

P4-18

LLPBK2

P4-25

TMI2

Table D–27 Ethernet Loopback Connector Pin Assignments
From
Pin No.

Signal

To
Pin No.

Signal

Description

P6-3

TRA+

P6-5

REC+

Through capacitor

P6-10

TRA-

P6-12

REC-

Through capacitor

P6-13

PWR

P6-6

RET

Through resistor
and LED

E
Interpreting LED Displays
This appendix explains the LED displays for the following items:
•

Graphics subsystem

•

Memory module

•

CPU module

•

I/O module

•

Tape adapter module

•

Tape drive controller module (TQK70)

•

Tape drive (TK70)

•

Optical compact disc drive (RRD40)

•

Power supply

E–1

E–2 Interpreting LED Displays

E.1 Graphics Subsystem LEDs
The graphics subsystem has one green LED on each module and a set of
red LEDs on the graphics frontplane.
If a module is operating correctly, the module’s green LED turns on. If
the system detects an error in a graphics module, the red LEDs display
an error code.
Table E–1 explains graphics error codes displayed by red LEDs.
Table E–1 Graphics Frontplane LED Error Displays
Display

Meaning

No power or faulty LEDs

Bad subsystem configuration

Faulty expansion module

Unused

Faulty output module

Unexpected interrupt

Faulty output or expansion module

Unused

Faulty base module

Restart error

Faulty base or expansion module

Insufficient capacity outside graphics
subsystem

Faulty base or output module

Faulty VDAC comparator

Faulty base, output, or expansion module

Catastrophic failure, power-up fault

= on.
o = off.

Interpreting LED Displays E–3

E.2 Memory Module LEDs
Each memory module has one red and one yellow LED. Table E–2
explains memory module LED displays.
Table E–2 Memory Module LED Error Displays
Red LED

Yellow LED

Meaning

No power to module or faulty LEDs.

Test not started.

Failed test or test not completed.

Test passed, no error detected.

= on.
o = off.

E.3 CPU Module LEDs
Each CPU module has one green LED and two sets of red LEDs, one set
for each CPU in the module. The green LED turns on if both CPUs are
operating correctly. If a CPU fails the self-test, the green LED does not
turn on and the failed CPU’s red LEDs display an error code. Table E–3
explains the CPU red LED displays.
Table E–3 CPU Module Error Displays
Display

Failed Test

No error detected or no power to module.

Primary in diagnostic executive.

Jump to console.

Build data and signal secondaries to exit first
wait loop.

Secondary in diagnostic executive wait loop.

Primary builds root configuration table.

Primary rebuild cache top of memory.

Secondaries exit wait loop and jump to console.

= on.
o = off.

E–4 Interpreting LED Displays

Table E–3 (Cont.) CPU Module Error Displays
Display

Failed Test

Primary processor determination, secondary
wait loop.

Search M-bus, save modtypes on stack, find
I/O board.

Map cache.

Cache test, parity enabled.

Cache TAG test.

FPU test.

FBIC register test.

Power-on condition.

= on.
o = off.

E.4 I/O Module LEDs
The I/O module has one green LED. This LED turns on if the I/O module
is operating correctly. If the LED does not tun on, there is a problem in
the module—the module has no power, or the LED is faulty.

E.5 Tape Adapter Module LEDs
The tape adapter module has one green LED and a set of red LEDs. The
green LED turns on if the tape adapter module is operating correctly. If
the system detects a tape adapter module fault, the red LEDs display
an error code. Table E–4 explains the tape adapter module red LED
displays.
Table E–4 Tape Adapter Module LED Displays
Display

Failed Test

Doorbell interrupt.

FBIC register verify error.

FBIC register miscompare occurred.

= on.
o = off.

Interpreting LED Displays E–5

E.6 Tape Drive Controller Module (TQK70) LEDs
The tape drive controller module has two LEDs. If the LEDs do not turn
on, there is no power to the module. The LEDs flash alternately if there
is a problem in communication between the tape drive controller and the
tape adapter module.

E.7 Tape Drive (TK70) LEDs
The front of the tape drive has three LEDs. Table E–5 explains possible
LED displays.
Table E–5 TK70 Tape Drive LED Displays
LED

Condition

Meaning

Green

You can operate the handle.

Off

Do not operate the handle.

Flashing

The cartridge is defective.

The drive is ready.

Flashing

The drive is in use.

The tape is write-protected.

Off

The tape is writable.

Flashing

A drive fault exists.
Press the Unload switch to attempt resetting.

Yellow

Orange

All three

E.8 Optical Compact Disc Drive (RRD40) LEDs
The optical compact disc drive has a green power indicator LED and a
green activity indicator LED. The power indicator turns on when the
optical compact disc drive power is on. The activity indicator turns on
when a disc is correctly loaded in the RRD40 drive. The activity indicator
flashes when the disc is transferring data.

E–6 Interpreting LED Displays

E.9 Power Supply LEDs
Each power supply has one green LED. The green LED on each power
supply turns on if the power supply is operating correctly. If neither
power supply LED is on, the power filter is probably faulty. The green
DCOK LED on the front panel turns on if the entire power supply system
is operating correctly.

F
SCSI and SSC Test Numbers and Utilities
F.1 SCSI Test Numbers
Comprehensive self-test
Invokes tests 0 through 9, the same as during power-up.
Test 0: SII Register Test
Verifies that the SII is present at expected addresses and that all
read/write bits can be written to 1 and 0.
Test 1: RAM Buffer Data Path Test
Verifies the data path from the CPU to the disk RAM buffer.
Test 2: RAM Buffer Data Access Path
Verifies that the RAM buffer can be accessed in longword, word, and byte
modes without modifying data that is not addressed.
Test 3: RAM Buffer Address/Data Test
Verifies that the entire RAM buffer can be written, a longword at a time,
without changing other data.
Test 4: SII Internal Loopback Test, SII Selection of Host
Verifies SII chip operation as an initiator selecting another device.
Test 5: SII Internal Loopback Test, Host Reselection of SII
Verifies SII operation as an initiator being reselected by another device.
Test 6: SII Internal Loopback Test, Host Selection of SII
Verifies SII operation as a target being selected by some other initiator.
F–1

F–2 SCSI and SSC Test Numbers and Utilities

Test 7: SII DMA Address and Byte Counter Test
Verifies SII DMA transfer capability.
Test 8: SII Interrupt Test 22
Verifies SII interrupts.
Test 9: SII External Loopback Test/Device Self-Test
Verifies the SCSI bus by checking for an installed loopback connector and
checking the IDs of devices on the SCSI bus.
Extended information summaries are one line per device in the following
format:
mid.id.lun(ttcuuu) errmsg
mid

Represents the M-bus ID of the module containing the SII.

Represents the SCSI device ID.

lun

Represents the SCSI device’s logical unit number(LUN).

Will be DK for devices supported by VMB, and xx for
others.

Represents the controller letter assigned to this SII.

uuu

Represents the unit number to be used when issuing utility
commands that require a unit number, or when booting.

errmsg

This field has two possible values. An STERR message
indicates a self-test command successfully executed but
received a medium or hardware error. An NOST message
is used for any other error. In both cases, the standard
extended status for a SCSI error follows on the same line.

Here is a sample display:

! 5.1.0(DKA100) NOST, OP = 1D, SNS = 2, ASNS = 04
" 5.7.0(DKA700) STERR, OP = 1D, SNS = 3, ASNS = 11
! The first line indicates that the drive was not ready.
" The second line indicates that the medium had a nonrecoverable read
error.

SCSI Utilities
Utility 100: Show SCSI for One I/O Module

F–3

F.2 SCSI Utilities
SCSI utility commands perform functions necessary for the SCSI self-test.
The following sections expain SCSI utility commands.

Utility 100: Show SCSI for One I/O Module
This utility generates information lines containing device address, that
device’s VMB name, device type, name, capacity, and characteristics.

Format
T mid 4 100 [unit] [full]

unit
Indicates the unit number of a SCSI device in a SHOW SCSI command.
The default setting is to show all units on this I/O module. Specifying
FFFF also selects all units.
full
Specifies whether a full or partial listing is displayed, as follows:
0

Brief listing. (Default setting if no unit is specified.)

Full listing. (Default setting if a unit is specified.)

The following is a sample display of a brief listing:

ADDR
----5.1.0
5.3.0
5.4.0
5.6
5.7.0

VMB
-----DKA100
DKA300
DKA400
DKA700

DEVTYP
-----DISK
DISK
RODISK
HOST
DISK

DEVNAM
------RZ55
RZ56
RRD40
SII-A
RZ23

NUMBYTS
------332 MB
665 MB
599 MB

REV
---0500
0100
210D

104

0610

CHAR
----

RM,WP

! The ADDR column indicates the device address (mid.id.lun). The

special case of mid.lun is for the SII chip controlling this SCSI bus
and is always followed by the string SII-c, where c is the controller
letter assigned to this I/O module.

F–4 SCSI Utilities
Utility 100: Show SCSI for One I/O Module

" The VMB column indicates the device name to use with VMB. If the

first two letters are xx, then VMB does not yet know about this device
type.

# The DEVTYP column indicates the device type.
$ DEVNAM is the device name.
% The NUMBYT column indicates the capacity of the device in bytes, to
three digits of precision.

& The CHAR column contains optional device characteristics. RM is

present if the device has removable media. WP is present if the device
is write-protected. The question mark (?) following the WP indicates
that the write-protect status could not be determined.

Optionally, a full listing can be generated. The following is a sample full
listing:

!
"

ADDR
----5.1.0

VMB
DEVTYP DEVNAM
NUMBYTS REV
------ ------ ------- ------- ---DKA100 DISK
RZ55
332 MB 0100
VID: DEC
PID: RZ55
(C) DEC
ANSI = 1, ECMA = 0, ISO = 0, RSPDATFMT = 1

CHAR
----

5.3.0

DKA300 DISK
RZ55
332 MB 0500
VID: DEC
PID: RZ55
(C) DEC
ANSI = 1, ECMA = 0, ISO = 0, RSPDATFMT = 1

5.4.0

DKA400 RODISK RRD40
599 MB 210D
VID: DEC
PID: RRD40
TM DEC
ANSI = 1, ECMA = 0, ISO = 0, RSPDATFMT = 1

5.6

HOST

RM,WP

SII-A

5.7.0

DKA700 DISK
RZ23
104 MB 0610
VID: DEC
PID: RZ23
(C) DEC
ANSI = 1, ECMA = 0, ISO = 0, RSPDATFMT = 1

! The second line of output for each device lists the vendor identification
(VID) and product identification (PID) strings from the INQUIRY
command. The second line of output is only included if the full
argument is 1.

" The third line indicates the conformance level of this device. The

values following ANSI, ECMA, and ISO, indicate the conformance
level with respect to the indicated standards. A 0 indicates no
conformance to the indicated standards. RSPDATFMT indicates
the response data format.

SCSI Utilities
Utility 103: Write/Read/Compare Blocks on Device

F–5

Utility 102: Spin Drive Up or Down

This utility spins the drive up or down as requested.

Format
T mid 4 102 unit

Unit
Unit is the unit number of the SCSI device to start or stop:
1

Start (spin up, default setting).

Stop (spin down).

You do not need to use this command before other utility commands, since
they will spin the drive up when necessary. This utility waits a maximum
of 100 seconds for the drive to complete the start or stop command.
Either of the following conditions cause the TEST UNIT READY
command, followed by the START command, to loop forever:
•

Loop-on-error is set and an error occurs during the TEST UNIT
READY or START UNIT command.

•

Loop-on-test is set.

The command loops forever unless TEST UNIT READY reports ready.

Utility 103: Write/Read/Compare Blocks on Device
This utility writes, reads, and compares 8 Kbytes, starting at block 0
and then at the block specified in the command. Any compare errors are
indicated. You can repeat this command to allow for acoustical testing of
drives.

Format
T mid4 103 unit [block] [pattern]

F–6 SCSI Utilities
Utility 103: Write/Read/Compare Blocks on Device

unit
Indicates the unit number of the SCSI device on which to perform the
write/read/compare operation.
block
Indicates the target block for the second write/read/compare operation.
The default target is the last blocks on the device.
pattern
Specifies a value from 016 to FF16 . This value is used as the data pattern
for each byte of the write/read/compare operation. The default pattern is
5516 .
This command can alter the user data. If the system is in user mode
and write operations are disabled in user mode, an error is returned.
Otherwise, the following prompt appears:
%SCSI-I-DEVINF, 3.1.0 DKA100 DISK RZ55

332 MB 0500

%SCSI-W-WRTUSRDAT
%SCSI-Q-RUSURE?

At this point, you can type yes to proceed with the command execution.
Typing no or pressing Ctrl C or Return aborts the command.
Either of the following conditions cause the test to loop forever during the
read/write/compare operation:
•

Loop-on-error is set and (1) an error occurs during the read or write
operations, or (2) the compare operation fails.

•

Loop-on-test is set.

NOTE
This command is designed to work with direct-access SCSI
devices. Using this command with devices other than directaccess SCSI devices can yield unpredictable results.

SCSI Utilities
Utility 104: Format Unit

F–7

Utility 104: Format Unit
This utility formats the specified unit, using all specified current or
default parameters. You cannot specify additional defective blocks.

Format
T mid 4 104 unit [cur/def]

unit
Indicates the unit number of the SCSI device to format.
cur/def
Lets you specify the current or default parameters.
1

Use the current format parameters (default setting).

Use the default format parameters.

This command can alter user data. If the system is in customer service
mode and write operations are disabled, an error is returned. Otherwise,
the following prompt appears:
%SCSI-I-DEVINF, 3.1.0 DKA100 DISK RZ55

332 MB 0500

%SCSI-W-WRTUSRDAT
%SCSI-Q-RUSURE?

Type yes to proceed with the command. Typing no or pressing Ctrl C or
Return aborts the command.
The system displays the type of parameters, current or default, before the
command proceeds:
%SCSI-I-DEFFMTPAR
or
%SCSI-I-CURFMTPAR

Formatting is a time-consuming operation that destroys the data on the
disk. For this reason, the system prompts you to confirm that you want to
format the unit:
%SCSI-I-RDYFMT
%SCSI-Q-RUSURE?

F–8 SCSI Utilities
Utility 106: Self-Test

To proceed with the format operation, type yes. The message %SCSI-IFMTUNIT... confirms that the unit is being formatted.
To cancel the command without modifying the data on the device, enter
no or press Ctrl C or Return .
This command waits upto 60 minutes for the format command to
complete. Upon successful completion, a complete message appears
on the screen.
NOTE
This command is designed to work with direct-access SCSI
devices. Using this command devices with other than directaccess SCSI devices can yield unpredictable results.

Utility 106: Self-Test
This utility performs a send diagnostic command with the slftst bit (and
optionally the unitof1 bit) asserted.

Format
T mid 4 106 unit [unitofl]

unit
Indicates the unit number of the SCSI device on which to perform the
self-test command.
unitof1
Indicates the unit off-line bit setting.
1

Set unitof1 bit.

Do not set unitof1 bit (default setting).

NOTE
Setting the unitof1 bit to 1 may allow writing to user data.
This command can alter user data. If the system is in Customer Services
mode and write operations are disabled, an error is returned. Otherwise,
the following prompt appears:

SCSI Utilities
Utility 107: Perform Seeks on Device

%SCSI-I-DEVINF, 3.1.0 DKA100 DISK RZ55

F–9

332 MB 0500

%SCSI-W-WRTUSRDAT
%SCSI-Q-RUSURE?

To proceed with the command, type yes.
To cancel the command, enter no or press Ctrl C or Return .
The test waits upto 10 minutes for the self-test command to complete.
Either of the following conditions cause the test to loop forever while
executing the Send Diagnostic command:
•

Loop-on-error is set and an error occurs during the Send Diagnostic
command.

•

Loop-on-test is set.

Utility 107: Perform Seeks on Device
This utility performs a seek to logical block 0, then to the logical block
specified in the command. You can repeat this command to allow for
acoustical testing of drives.

Format
T mid 4 107 unit [block]

unit
Indicates the unit number of the SCSI device on which to perform the
seek operation.
block
Indicates the target block for second seek operation. The default is the
last block on the device.
Either of the following conditions cause the test to loop forever while
executing the seek operation:
•

Loop-on-error is set and an error occurs during the seek command.

•

Loop-on-test is set.

F–10 SCSI Utilities
Utility 108: Read Capacity

Press Ctrl C to stop the utility.
NOTE
This command is designed to work with direct-access SCSI
devices. Using this command with devices other than directaccess SCSI devices can yield unpredictable results.

Utility 108: Read Capacity
This utility executes a Read Capacity command, then reports the returned
data.

Format
T mid 4 108 unit

unit
Indicates the unit number of the SCSI device on which to perform read
capacity operation.
Here is a sample output:

! BLKSIZ = 00000200
" MAXBLK = 0009E74F
! BLKSIZ indicates the size of the blocks on the SCSI device in bytes
(hexadecimal).

" MAXBLK indicates the maximum logical block number (hexadecimal)
addressable on the SCSI device.

Either of the following conditions causes the test to loop forever while
executing the Read Capacity command:
•

Loop-on-error is set and an error occurs during the Read Capacity
command.

•

Loop-on-test is set.

In either case, the normal output is not generated. Press Ctrl C to stop the
utility.

SCSI Utilities
Utility 10B: Write/Read/Compare Every Block on Disk and Reassign Bad Blocks

F–11

Utility 10B: Write/Read/Compare Every Block on Disk and
Reassign Bad Blocks
This command writes, reads, and compares all blocks on the device. If a
media error (sense key 3) occurs during the write or read operation, or the
compare operation fails, a reassign block command is executed specifying
the failing block. Any other errors are reported. Errors while mapping
out bad blocks do not terminate the operation.

Format
T mid 4 10B unit [pattern]

unit
Indicates the unit number of the device on which to map bad blocks.
pattern
Used as the data pattern for each byte of the write/read/compare
operation. Specify value from 016 to FF16 . The default setting is 5516 .
This command can alter user data. If the system is in customer service
mode and write operations are disabled in user mode, an error is returned.
Otherwise, the following prompt appears:
%SCSI-I-DEVINF, 3.1.0 DKA100 DISK RZ55

332 MB 0500

%SCSI-W-WRTUSRDAT
%SCSI-Q-RUSURE?

To proceed with the command, type yes.
To stop the command, enter no or press Ctrl C or Return .
The message %SCSI-I-MAPPNGBADBLKS... confirms that the command is
in progress.
The following is a sample dialog:
CPU10>> T 5 4 10B 100
%SCSI-I-DEVINF, 3.1.0 DKA100 DISK RZ55

332 MB 0500

F–12 SCSI Utilities
Utility 1FF: Set User Write Enable Bit

%SCSI-W-WRTUSRDAT
%SCSI-Q-RUSURE? Y
%SCSI-I-MAPPNGBADBLKS...
%SCSI-E-RDERR, LBN = 000F1234
%SCSI-E-STS = D2
%SCSI-I-EXTSTS, OP = 2A, SNS = 3, ASNS = 11, INF = 000F123
%SCSI-I-BLKREASS
%SCSI-I-BADBLKS = 1
%SCSI-I-REASSBLKS = 1
%SCSI-I-ERRBLKS = 0
%SCSI-S-STS = 01
CPU10 >>>

NOTE
This command is designed to work with direct-access SCSI
devices. Using this command with devices other than directaccess SCSI devices can yield unpredictable results.

Utility 1FF: Set User Write Enable Bit

This utility sets the state of the user write enable bit for the SCSI bus
on the I/O module specified by the module ID. SCSI buses on other I/O
modules are not affected.

Format
T mid 4 1FF enb/dis

enb/dis
Enables or disables user write operations.
0

Disable user write operations. In user mode, do not allow commands
that can alter user data.

Enable user write operations. In user mode, allow commands that can
alter user data.

Even when the write bit is enabled, commands that can alter user data
still require confirmation before the system attempts the operation.

SCSI and SSC Test Numbers and Utilities F–13

F.3 System Support Chip (SSC) Tests
The following section describes each system support chip (SSC) self-test.
Because the meaning of each error code value is different for each SSC
test, each test number entry explains the SSC error codes generated by
that test. All SSC self-tests run in customer or field service mode.
SSC self-tests do not require loopback connectors.
Test 0: Test Format Errors
The self-test reports a test format error if a test command is invalid. The
code shows the test number as 0 for these errors. An error of this type
indicates that the desired test was not executed.
Table F–1 shows the possible codes for test 0.
Table F–1 Test Format Error Codes
Error Code

Meaning

00000010

Mode bits are invalid. (Both field service and Manufacturing
bits were set).

00000020

Wrong number of arguments passed by T command.

00000030

Invalid test number passed by T command.

00000040

Test cannot be performed in the present mode.

Test 1: Programmable Timer Register
The timer next interval (TNIR) and the timer interrupt vector (TIV)
registers are written/read/compared with various patterns.
Table F–2 shows the possible error codes for test 1.
Table F–2 Programmable Timer Error Codes
Error Code

Meaning

SSC base register was not initialized properly.

Timer interrupt vector (TIV) register write/read back error.

Timer next interval register (TNIR) write/read back error.

Probable cause for failure: The SSC or the pathway to the SSC.
Probable failed FRU: I/O module.

F–14 SCSI and SSC Test Numbers and Utilities

Test 2: Programmable Timers Transfer Bit
This test exercises the programmable timer transfer bit in the timer
control register (TCR). Table F–3 shows the possible error codes for test
2.
Table F–3 Timer Transfer Error Codes
Error Code

Meaning

SSC base register was not initialized properly.

TNIR changed after run bit in TCR was set.

Transfer did not occur correctly.

Probable cause: SSC or the pathway to the SSC (assuming the previous
tests have passed).
Probable failed FRU: The I/O module.
Test 3: Programmable Timers Run Bit
This test exercises the timer control register (TCR) run bit. Table F–4
shows the possible error codes for test 3.
Table F–4 Timer Run Bit Error Codes
Error Code

Meaning

SSC base register was not initialized properly.

Timer is not incrementing.

Timer is running with the run bit clear.

Run bit did not clear upon overflow of timer with stop bit set.

Timer not clear after timer overflow and stop step.

Run bit cleared upon overflow of timer with stop bit clear.

Either the timer is incrementing unexpectedly or TNIR did not
transfer.

Probable cause: The SSC or the pathway to the SSC (assuming the
previous tests have passed).
Probable failed FRU: The I/O module.

SCSI and SSC Test Numbers and Utilities F–15

Test 4: Programmable Timer Single Step
This test exercises the timer control register (TCR) single-step bit.
Table F–5 shows the possible error codes for test 4.
Table F–5 Timer Single-Step Error Codes
Error Code

Meaning

SSC base register was not initialized properly.

Time out on ss interval.

TIR != TNIR upon (overflow and stop bit set).

TIR != TNIR upon (overflow and stop bit clear).

Run bit set unexpectedly.

TIR not incrementing.

Probable cause: The SSC or the pathway to the SSC (assuming the
previous tests have passed).
Probable failed FRU: The I/O module.
Test 5: Programmable Timer Interrupt
This test exercises the programmable timer in interrupt mode. Table F–6
shows the possible error codes for test 5.
Table F–6 Timer Interrupt Error Code
Error Code

Meaning

SSC base register was not initialized properly.

Interrupt time out error.

Interrupt enable bit does not work in disable mode.

FBIC CSR IRGEN bit (for IPL 14) does not work.

Either TIR is incrementing unexpectedly or TNIR did not
transfer.

Wrong IPL level (should be 14).

Probable cause: Varies (assuming the previous tests have passed).
Table F–7 relates erors, causes, and probable failed FRU.

F–16 SCSI and SSC Test Numbers and Utilities

Table F–7 Causes of Timer Interrupt Errors
Error Code

Cause

SSC or pathway to SSC.

SSC or CPU to M-bus to SSC pathway.

SSC or pathway to SSC.

Pathway to IO FBIC or IO FBIC.

SSC or pathway to SSC.

FBIC, CPU to M-bus to SSC pathway, or CPU.

Test 6: 100 Hz Interval Timer
This test ensures that the 100 Hz interval timer can cause an interrupt
and verifies the IOCSR clock interrupt enable bit function. Table F–8
shows the possible error codes for test 6.
Table F–8 Timer Error Codes
Error Code

Meaning

SSC base register was not initialized properly.

Interval timer interrupt did not occur.

Interrupt occurred with iocsr$clkien disabled.

Probable cause: Varies (assuming the previous tests have passed).
Table F–9 relates errors, causes, and probable failed FRUs.
Table F–9 Timer Error Causes
Error

Cause

Probable Failed FRU

SSC or pathway
to SSC

I/O module

SSC, IOCSR, or
CPU to M-bus to
SSC pathway

I/O or CPU module

IOCSR

I/O module

SCSI and SSC Test Numbers and Utilities F–17

Test 7: Time-of-Year Clock
This test verifies that the time-of-year (TOY) clock counts up if it contains
a nonzero value. The test also verifies that the counter stops at 0.
Table F–10 shows the possible error codes for test 7.
Table F–10 Clock Error Codes
Error
Code

Meaning

SSC base register was not initialized properly.

Battery low set warning.

TOY is not counting when it has nonzero value.

TOY did not stop counting at 0.

Probable cause: Varies (assuming the previous tests have passed).
Table F–11 relates errors, causes, and probable failed FRUs.
Table F–11 Cause of Clock Errors
Error

Cause

Probable Failed FRU

SSC or pathway
to SSC

I/O module

SSC or
rechargeable
battery
mechanism

I/O module or battery

3, 4

SSC or pathway
to SSC

I/O module

Test 8: Ethernet Station Address ROM
This test verifies the Ethernet station checksum address ROM (ESAR).
The format for the address in the ROM is
A-B-C-D-E-F-G-H
The first six bytes (A to F) are the station address, and the last 2 bytes (G
and H) are the checksum.

F–18 SCSI and SSC Test Numbers and Utilities

The following formula is used to verify the checksum:

Checksum = (A 3 210) + (B 3 22 ) + (C 3 29 ) + (D 3 21 ) + (E 3 28 ) + F mod 216 0 1
Checksum = G 3 28 + H
The only possible error for test 8 is an invalid checksum. The error code 1
represents this failure.
Probable cause: An invalid checksum probably results from problems in
the ESAR, IOCSR, or IOCSR-ESAR pathway.
Probable failed FRU: The I/O module.

SCSI and SSC Test Numbers and Utilities F–19

F.4 CPU Test Numbers
Table F–12 outlines individual CPU self-test numbers.
Table F–12 CPU Test Numbers and Their Meaning
Test Number

Tested Module

CFPA

CVAX virtual mode

FBIC interrupt (MIRQ/CIRQ)

C-bus parity

CVAX cache 1

FBIC M-bus test modes (power-up only)

CPU ROM checksum

FBIC cache counters (power-up only)

CVAX virtual mode (power-up only)

Index
A
AC filter
removing/replacing, 4–24 to
4–25
AC input power, 1–34
AC switch assembly
removing/replacing, 4–25 to
4–27
AC switch frame, 4–25, 4–27
Adapter modules
L2002, 1–3
L2008, 1–3
Q-bus, 1–3
Alternate console, using, 2–4
Antistatic kit, 3–1
Antistatic procedures, 3–1, 4–4, 5–1
Architecture of workstation, 1–3 to
1–5, 4–4
Asynchronous multiplexer (CXY08),
1–23

B
Back cover (system unit)
removing/replacing, 3–14 to
3–15
Backplane, 1–12 to 1–14, 3–14
removing/replacing, 4–29 to
4–31
slots, 4–4
Battery, 1–28
Battery pack
removing/replacing, 4–2 to 4–3
Blank cover, 4–9

Blank panel, 4–9, 5–26
BOOT command, 2–4
Boot device, 1–10
Booting, 2–89
error messages, 2–89 to 2–90
Bootstrapping, 1–11

C
Cabling information, B-1 to B-14
Card cage slots, 4–4
Changing configuration, 5–3 to
5–5
CONFIG program, 5–4 to 5–5
Configuration changing, 5–3 to
5–5
Configuration display
first-level, 2–7
mid number, 2–9
Q-bus, 2–10
Configuration of workstation
See Architecture
Configuration testing, 5–2, 5–5
Console commands, C–1 to D–1
Console mode, 1–11, 2–4
CONTINUE command, 2–4
Control panel, 1–10 to 1–11
Control panel assembly
removing/replacing, 4–7 to 4–8
Control panel module
removing/replacing, 4–7 to 4–8
Covers
internal, 1–27
Covers, function, 1–27 to 1–29
graphics, 1–29
I/O, 1–28

Index 1

2 Index

Covers, function (cont’d.)
mass storage, 1–29
Q-bus, 1–29
Covers, removing/replacing, 3–3 to
3–8, 3–12, 3–14 to 3–15
back (system unit), 3–14 to
3–15
blank, 4–9
front (system unit), 3–3 to 3–4
graphics, 3–7 to 3–8
graphics frontplane, 3–8
I/O, 3–5 to 3–7
mass storage, 3–12
CPU module, 1–15 to 1–16
installing expansion, 5–12
CPU self-test
See Self-test
CPU test numbers, F–19
Customer mode
See System test
CXY08, 1–23
installing, 5–6

D
DC power, 1–34
Drive mounting brackets, installing,
5–19, 5–21 to 5–25
hard disk drive (RZ55), 5–22 to
5–23
hard disk drive (RZ56), 5–24 to
5–25
tape drive (TK70), 5–21
Drive shock mounts, installing,
5–19, 5–19 to 5–20
DSV11, 1–24
installing, 5–9
Dual CPU module
See CPU module

E
EOS clips, 4–2
Equipment specifications, A–1 to
A–15
LK201 keyboard, A–4 to A–5
RRD40 optical compact disc drive,
A–14 to A–15
RZ55 SCSI hard disk, A–9 to
A–10
RZ56 SCSI hard disk, A–11 to
A–12
TK70 tape drive, A–13 to A–14
VR295 monitor, A–2 to A–3
VS60S system unit, A–2
VSXXX-AA mouse, A–5 to A–6
VSXXX-AB tablet, A–7 to A–8
Error codes
See also Self-test
See also System test
Expansion modules
installing, 5–12 to 5–13
External connectors
types of, 1–4

F
Fans, 1–34
removing/replacing, 4–27 to
4–29
FCC clips, 4–2
Field service mode
See System test
Front cover (system unit)
removing/replacing, 3–3 to 3–4
FRUs, removing/replacing, 4–1 to
4–33
See also Options, installing
ac filter, 4–24 to 4–25
AC switch assembly, 4–25 to
4–27
backplane, 4–29 to 4–31
battery pack, 4–2 to 4–3

Index 3

FRUs, removing/replacing (cont’d.)
control panel assembly, 4–7 to
4–8
control panel module, 4–7 to
4–8
fans, 4–27 to 4–29
graphics frontplane, 3–8
graphics module, 4–5 to 4–6
hard disk drive (RZ55), 4–13 to
4–15
hard disk drive (RZ56), 4–16 to
4–20
keyboard, 4–32
M-bus module, 4–5 to 4–6
modules, system, 4–4 to 4–6
monitor, 4–32
mouse, 4–33
power supplies, 4–20 to 4–24
Q-bus module, 4–9 to 4–10
tablet, 4–33
tape drive (TK70), 4–11 to 4–12
tape drive (TS05), 4–13
tape drive controller module
(TQK70), 4–9 to 4–10

Graphics self-test (cont’d.)
See Self-test
Grille
removing, 4–21

H
Halt button, 1–11, 2–4
Hard disk drive (RZ55), 1–33
installing, 5–30 to 5–32
removing/replacing, 4–13 to
4–15
troubleshooting, 2–21
Hard disk drive (RZ56), 1–33
installing, 5–33 to 5–36
removing/replacing, 4–16 to
4–20
troubleshooting, 2–21
Hardware problems
See Troubleshooting
HDI
See Graphics frontplane

I
G
Graphics bus, 1–14
Graphics bus modules, 1–21 to
1–22
Graphics cover, 1–29
See also Covers, function
See also Covers, removing/replacing
Graphics frontplane, 1–14, 3–9
removing/replacing, 3–8, 3–9
Graphics module
base, 1–21
expansion, 1–21
frontplane, 1–21
installing expansion, 5–13
output, 1–21
removing/replacing, 4–5 to 4–6
Graphics self-test

I/O cable, 1–28, 3–6
I/O cover, 1–28
See also Covers, function
See also Covers, removing/replacing
I/O module, 1–18
Installing options
See also Options, installing
CPU expansion module, 5–12
graphics expansion module, 5–13
hard disk drive (RZ55), 5–19
hard disk drive (RZ56), 5–19
memory expansion module, 5–12
optical compact disc drive
(RRD40), 5–15 to 5–17
Q-bus adapter module, 5–14
tape adapter module, 5–18
tape drive (TK70), 5–19

4 Index

Installing options (cont’d.)
tape drive controller module
(TQK70), 5–26 to 5–28
Interpreting LED displays
CPU module LEDs, E–3 to E–4
graphics subsystem LEDs, E–2
I/O module LEDs, E–4
memory module LEDs, E–3
optical compact disc drive
(RRD40) LEDs, E–5
power supply LEDs, E–6
tape adapter module LEDs, E–4
to E–5
tape drive (TK70) LEDs, E–5
tape drive controller module
(TQK70) LEDs, E–5

K
Keyboard, 1–8
removing/replacing, 4–32
Keyswitch, 1–10
Kits
antistatic, 3–1
option, 5–1 to 5–39
upgrade, 5–1

L
L2002
adapter module, 1–3
L2008
adapter module, 1–3
Loopback connectors, 2–5, 2–10
Loops, setting, 2–16

M
M3108, 1–24
M3119, 1–23
M7530, 1–25
Mass storage cover, 1–29
See also Covers, function

Mass storage cover (cont’d.)
See also Covers, removing/replacing
removing/replacing, 3–12
Mass storage devices, 1–30 to
1–33
See also Hard disk drive (RZ55)
See also Hard disk drive (RZ56)
See also Optical compact disc
drive (RRD40)
See also Tape drive (TK70)
See also Tape drive (TS05)
troubleshooting, 2–20
M-bus, 1–12
M-bus module, 1–15 to 1–20
removing/replacing, 4–5 to 4–6
M-bus modules, 1–3
Medallion (CPU upgrade), 5–12
Memory
Self-test
See Self-test
System test
See System test
Memory expansion module
installing, 5–12
Memory module, 1–16 to 1–18
installing expansion, 5–12
Module IDs, 2–8
Modules, system
See also FRUs, removing/replacing
See also Installing options
Monitor, 1–6
connections, 1–8
controls, 1–6
removing/replacing, 4–32
tests, 2–19 to 2–20
troubleshooting, 2–10
Mouse, 1–8
removing/replacing, 4–33
Moving the workstation, 3–13
MS60
See Memory module

Index 5

Network interface (NI), 2–23
self-test
See Self-test
system test
See System test
Nonvolatile RAM (NVR), 3–6, 4–2,
4–3, 4–5

Part numbers, B–1 to B–7
hardware documentation, B–5
to B–6
option kits, B–4 to B–5
software documentation, B–7
system FRUs, B–1 to B–4
Pedestal cams (removing), 4–20
Pin assignments
buses for slots 10–12, D–7
buses for slots 1–9, D–7
communications connector, D–4
DCOK connector on connector
J27, D–23
Ethernet loopback connector,
D–25
fan connector on connector J26,
D–22
graphics backplane for slot 3,
connector A, D–16
graphics backplane for slots 1–2,
connector A, D–18
graphics backplane for slots 1–2,
connector B, D–19
I/O cover ribbon cable, D–2
I/O cover SCSI cable, D–2
keyboard and mouse/tablet
connector, D–3
M-bus backplane for slots 3–9,
connector B, D–8
M-bus backplane for slots 4–8,
connector A, D–10
M-bus MBRQ connection per slot,
D–11
modem loopback connector, D–25
module IDs, D–7
power connector on connector J25,
D–21
power connector on connector J29,
D–23
printer/console connector, D–5
printer/console loopback
connector, D–24

O
On/off switch, 1–10
Operating mode, 2–4
Optical compact disc drive (RRD40),
1–33
installing, 5–15 to 5–17
troubleshooting, 2–21
Options
Q-bus, 1–3
Options, installing, 5–1 to 5–39
CPU expansion module, 5–12
graphics expansion module, 5–13
hard disk drive (RZ55), 5–30 to
5–32
hard disk drive (RZ56), 5–33 to
5–36
memory expansion module, 5–12
optical compact disc drive
(RRD40), 5–15 to 5–17
Q-bus adapter module, 5–14
tape adapter module, 5–18
tape drive (TK70), 5–28 to 5–29
tape drive controller module
(TQK70), 5–26 to 5–28
unpacking and inspecting, 5–2

6 Index

Pin assignments (cont’d.)
Q-bus backplane for slot 9,
connector A, D–14
Q-bus backplane for slots 10–12,
connector A, D–12
Q-bus backplane for slots 10–12,
connector B, D–13
Q-bus slot priority, D–12
summary of loopback connections,
D–24
ThickWire Ethernet connector,
D–6
Power output LED, 1–11
Power supplies, 1–34
removing/replacing, 4–20 to
4–24
Power-up self-test, 1–10, 2–6 to
2–7, 5–2
failure to complete, 2–12 to
2–15

Q
Q-bus, 1–13
adapter module, 1–13, 1–19
adapter modules, 1–3
cover, 1–29
modules, 1–23 to 1–26
options, 1–3
priority scheme, 1–13
Q-bus adapter module
installing, 5–14
Q-bus adapter module self-test
See Self-test
Q-bus module
removing/replacing, 4–9 to 4–10

R
Removing
SCSI terminator, 3–10 to 3–11
Removing/replacing
See alsoCovers, removing/replacing

Removing/replacing (cont’d.)
See alsoFRUs, removing/replacing
Restart/Run button, 1–11, 2–4
RGB cables, 3–8
RRD40
See Optical compact disk drive
RZ55
See Hard disk drive
RZ56
See Hard disk drive

S
SCSI bus, 5–16, 5–31
SCSI connector, 3–10, 5–16
SCSI extended information strings,
2–28
SCSI ID settings
hard disk drive (RZ55), 4–15,
5–30
hard disk drive (RZ56), 4–17
optical compact disc drive
(RRD40), 5–15
SCSI sense code values, 2–28 to
2–29
SCSI terminator, 5–16
removing, 3–10 to 3–11
SCSI test
See also Self-test
See also System test
SCSI test numbers, F–1 to F–2
SCSI utilities, F–3 to F–12
Self-test, 2–6
CPU, 2–36 to 2–39
error codes, 2–36 to 2–39
CXY08 module
error codes, 2–45
DSV11 module
error codes, 2–46 to 2–47
error messages, display, 2–7
graphics, 2–40
error codes, 2–41
I/O display, 2–23
individual modules, 2–9, 2–16

Index 7

Self-test (cont’d.)
memory, 2–39
error codes, 2–39
network interface (NI), 2–34 to
2–35
error codes, 2–35
Q-bus adapter module (DWFQA),
2–43
Q-bus options, 2–43
SCSI, 2–24 to 2–29
error codes, 2–25 to 2–27
serial line adapter (DZ), 2–31
error codes, 2–32 to 2–33
setting loops for, 2–16
system support chip (SSC), 2–30,
F–13 to F–18
tape adapter module, 2–41
error codes, 2–41
tape drive controller module
(TQK70), 2–41
error codes, 2–42 to 2–43
tape drive controller module
(TSV05)
error codes, 2–47 to 2–48
Serial line adapter (DZ)
self-test
See Self-test
system test
See System test
Shipping brackets, 3–13
Special tests, setting up, 2–17
START command, 2–4
System modules
See Modules, system
System support chip (SSC) self-test
See Self-test
System test, 2–17, 2–48
customer mode, 2–17
CXY08 module
error codes, 2–83 to 2–85
DSV11 module
error codes, 2–86 to 2–87
DWFQA Q-bus adapter module
error codes, 2–83

System test
DWFQA Q-bus adapter module
(cont’d.)
self-test error codes, 2–43 to
2–44
error display, 2–18
exceptions, 2–49 to 2–52
field service mode, 2–17
LEGSS, 2–71
error codes, 2–71
GVAX errors, 2–72
host errors, 2–72
machine check, 2–52 to 2–56
memory, 2–60
error codes, 2–60
extended information, 2–60
network interface (NI), 2–62
error codes, 2–62
kernel call error codes, 2–63
Q-bus adapter module (DWFQA)
error codes, 2–83
self-test error codes, 2–43 to
2–44
SCSI, 2–66 to 2–68
error codes, 2–68 to 2–69
serial line adapter (DZ), 2–56
error codes, 2–57, 2–58
tape drive controller module
(TQK70), 2–72
error codes, 2–73 to 2–83
tape drive controller module
(TSV05)
error codes, 2–87 to 2–89
TSV05 module
error codes, 2–87 to 2–89
System unit, 1–8 to 1–34
turning off, 3–2

T
Tablet, 1–8
removing/replacing, 4–33
Tape adapter module, 1–19 to
1–20
installing, 5–18

8 Index

Tape adapter module self-test
See Self-test
Tape drive (TK70), 1–32
installing, 5–28 to 5–29
removing/replacing, 4–11 to
4–12
troubleshooting, 2–20
Tape drive (TS05), 1–33
removing/replacing, 4–13
Tape drive controller module
(TQK70), 1–25, 5–18
See System test
configuring, 5–26
installing, 5–26 to 5–28
removing/replacing, 4–9 to 4–10
self-test
See Self-test
system test
See System test
T commands, 2–22
TEST commands
See T commands
Testing configuration, 5–2, 5–5
Test modes
customer mode, 2–5
field service mode, 2–5
TK70
See Tape drive
TQK70
See Tape drive controller module
Troubleshooting
hard disk drive (RZ55), 2–21
hard disk drive (RZ56), 2–21
mass storage devices, 2–20 to
2–21
monitor, 2–10
no monitor display, 2–10
optical compact disc drive
(RRD40), 2–21
power-up self-test failure, 2–12
to 2–15
tape drive (TK70), 2–20
TS05, 1–25
TS05 Tape Drive

TS05 Tape Drive (cont’d.)
installing, 5–36

U
Upgrade kit, 5–1
Upgrading
See Options, installing

V
VMS SYSGEN, 5–4 to 5–5

W
Workstation architecture, 1–3 to
1–5