Digital PDFs

EK-VGB11-DX-A01

June 1994

50 pages

Original

0.4MB

Document:	VGB11 Video Terminal Installation and User Guide
Order Number:	EK-VGB11-DX
Revision:	A01
Pages:	50
Original Filename:

OCR Text

VGB11 Video Terminal
Installation and User Guide
Order Number: EK-VGB11-DX. A01

June 1994
Notice
The information contained in this document is subject to change without any
previous notice. Tracor Europa B.V. shall not be liable for errors contained
herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this material.
FCC ID: AO9-VGB10
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. Any changes or modifications made to this equipment
may void the user’s authority to operate this equipment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio and television reception; however, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
EMI Requirements for Canadian Market
This digital apparatus does not exceed the class B limits for radio noise
emissions from digital apparatus as set out in the radio interference regulations
of the Canadian Department of Communications.
Specifications EMI pour le Marche Canadien
Le présent appareil numérique n’émet pas de bruits radioélectriques depassant
les limites applicables aux appareils numériques de classe prescrites dans
le règlement sur le brouillage radioélectrique édicté par le Ministère des
Communications du Canada.
Tracor is a registered trademark of Tracor Europa B.V.
ADDS is a trademark of Applied Digital Data Systems, Inc. IBM, ProPrinter,
and PS/2 are registered trademarks of International Business Machines
Corporation. SCO is a trademark of Santa Cruz Operations, Inc. TVI is a
trademark of TeleVideo, Inc. UNIX, VMS, and VT are trademarks of Digital
Equipment Corporation. WY and WYSE are registered trademarks of Wyse
Technologies.
PUBLICATION ISSUED BY:
Tracor Europa B.V.
Copyright © 1994 by Tracor Europa B.V.
Printed in Taiwan.

Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 Installation and Set-Up
Install the tilt/swivel stand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install your terminal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set up your terminal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save your settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1–1
1–2
1–4
1–9

2 Desktop Features
Invoking Desktop Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calculator feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show Character Sets feature . . . . . . . . . . . . . . . . . . . . . . . . .
Banner message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2–1
2–1
2–2
2–3
2–4
2–4

3 Maintenance and Troubleshooting
Cleaning your Video Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the ROM Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disposing of your Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3–1
3–1
3–4
3–4

4 Defining Keys
Define Key Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4–1

iii

A Specifications
B Keyboard Function Keys
User Definable Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

B–1
B–1

C Compose Characters
Compose Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C–1

ANSI-Style Keyboard Layout . . . . . . . . . . . . . . . . . . . . . . . . .
PC-Style Keyboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . .
Comm1—Serial Communication/Printer Ports . . . . . . . . . . . .
Comm2—MMJ Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel Printer Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1–6
1–6
A–4
A–4
A–4

Identifying and Correcting Problems . . . . . . . . . . . . . . . . . . .
Standards Conformance and Approvals . . . . . . . . . . . . . . . . .
Local Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other Available Local Functions . . . . . . . . . . . . . . . . . . . . . .
Multinational Character Set . . . . . . . . . . . . . . . . . . . . . . . . .
ISO Latin (Latino, Latina) 1 Specific . . . . . . . . . . . . . . . . . .
ISO Latin (Latino, Latina) 2 . . . . . . . . . . . . . . . . . . . . . . . . .
ISO Latin-Greek, Latino-Griego, Latin-Grec, Latina-Greca
................................................
National Replacement Character Sets (NRCS) . . . . . . . . . . . .

3–2
A–5
B–2
B–5
C–2
C–4
C–4

Figures
1–1
1–2
A–1
A–2
A–3

Tables
3–1
A–1
B–1
B–2
C–1
C–2
C–3
C–4
C–5

C–6
C–7

Preface

Overview

This guide is for users who wish to install and configure the
VGB11 video terminal. This guide describes how to connect
cables and enter the Set-up Menu to make changes, as needed.
This guide also has reference tables for troubleshooting,
specifications, and compose sequences.
For more detailed information on programming the terminal,
refer to the Video Terminal Programmer Information manual.
Note

Environment

This product has been designed and manufactured to
minimize the impact to the environment. The packaging
is recyclable and the terminal can be returned for proper
disposal.

Before You
Start

Ensure that you have received the following:
•

Video terminal

•

Keyboard

•

Power cord

A small flat-blade screwdriver may be needed to install the
communication or the printer cables.

Conventions

The following conventions are used in this document:
Convention

Meaning

Shift Tab

Indicates two keys that you must press
in combination. Press and hold the first
key while you press the second key.

Shift Enter

Indicates two keys that you must press
in sequence. Press and release the first
key before you press the second.

Caps Lock Alt F11

Indicates three keys that you must
press in combination, holding the first
two down while pressing the third.

terminal

Describes the VGB11 video terminal.

Display

Menu items are in boldface type.

Note

Provides general information.

Caution

Provides information to prevent damage
to equipment.

Warning

Provides information to prevent injury.

1
Installation and Set-Up
Install the tilt/swivel stand.
1. Carefully set the terminal facedown.
2. Insert the hooks on the stand into the slots at the bottom of
the terminal.
3. Slide the stand to the right until it is locked by the two tabs
at the bottom of the terminal. (To remove the stand, press
the two tabs.)

DSG-000375

Insert hooks
and slide into
position.

Installation and Set-Up 1–1

Install your terminal.

Install your terminal.
To install your terminal, connect the cables to the terminal as
shown.

DSG-000376

Connect the
cables to the
terminal.

2
3

Comm 1 ( ) (male or female),
Parallel ( ),
Comm 2,
Keyboard,

1–2 Installation and Set-Up

Power cord.

Install your terminal.

Plug in the
power cord and
push the power
switch on.

The terminal will beep indicating that the power is on.

1
2

Power,

Set the
Brightness
and Contrast
controls.

Contrast,

Brightness

If necessary, set the brightness and contrast controls by doing
the following:
1. Set both controls to maximum by turning controls all the
way to the right ( ).
2. Adjust the Brightness control
by turning the control to the
left ( ) until the background raster is not visible. This sets
the black level.

by turning the control to the
3. Adjust the Contrast control
left ( ) to set the white level for comfortable viewing.

4. Repeat steps 2 and 3 as needed.

Installation and Set-Up 1–3

Install your terminal.

"Selftest OK"
appears on
screen.

The terminal takes a few seconds to warm up and complete its
power up self-tests. Then, the terminal should display ‘‘Selftest
OK.’’ If a problem occurs, go to Chapter 3.

Set up your terminal.
Overview

Use Set-Up to examine or change the terminal operating
features, such as the transmit speed, receive speed, or the
language. The Set-Up menus in this section will get you started
in operating the terminal. Only the basic Set-Up feature is
performed with this procedure. There are many more Set-Up
features in the terminal that you may wish to change.
Before changing the Set-Up features, contact your System
Manager, if necessary, for information on the terminal type,
terminal ID to host, and the communication settings.
Printer operations are suspended upon entering Set-Up and are
resumed upon exiting Set-Up.

Entering Set-up

To enter Set-Up, perform the following procedures:
On a . . .

Press . . .

ANSI-style keyboard

PC keyboard

Caps Lock

1–4 Installation and Set-Up

Print Screen

Set up your terminal.

Moving within a
Set-Up Menu

Use the arrow keys ( , , ,
) to move among the menus or
within a list, or to select buttons.

In a
menu . . .

Indicates . . .

A pull-right submenu is available.

...

A dialog box is available for you to specify more
information.

a
b
c

The menu item with the filled-in circle is enabled.
Only one of these items can be enabled at a time.
The menu item with the checkbox is enabled.

Press Enter Return Do or Select to start the action or to choose the
currently highlighted feature.
A dimmed menu item does not apply to the currently selected
mode.

Installation and Set-Up 1–5

Set up your terminal.

Keyboards
Figure 1–1 ANSI-Style Keyboard Layout
N o rt h A m er ican/U nit ed K ingdom ( W or d P r ocessing V er sion)
F5

F10

^
6

*
8

(

)

Tab

Ctrl

>
<

Shift

Compose
Character

7
Y

:
;

Alt
Function

F12

+
=

>
.

<
,

F11

F13

Help

F14

}

]

(ESC)

}

]

Return

Find

Insert
Here

Remove

Select

"
’

?
/

Shift

F17

F18

F19

F20

PF1

PF2

PF3

PF4

Compose
Character

Enter

MA-1520a-92.PS

Figure 1–2 PC-Style Keyboard Layout
North American

di gi tal
Esc

F11

F10

F12

Print
Screen

Scroll
Lock

SetUp

Pause

Break

Num Lock

*
8

^
6

7
Y

(

)

_
-

:
;

+
=

BackSpace

}

]

Tab

}

]

Insert

Home

Page
Up

Delete

End

Page
Down

Caps Lock Scroll Lock

Num
Lock

Home

PgUp

+
Caps
Lock

Shift

<
,

>
.

"
’
?
/

Enter

Shift

End

PgDn
Enter

Ctrl

Alt

Altl

Ctrl

0
Ins

.
Del

GSF-MK2510-29-DG

LJ-00226a-TI0.PS

1–6 Installation and Set-Up

Set up your terminal.

Select the
Set-Up
language.

This language selection is for Set-up only and does not affect
keyboard, character set, or printer settings.

Port selected,
Transmit speed (9600), Parity (N), Word
size (8), Stop bits (1),
Character set,
Keyboard language,
Emulation mode.

Installation and Set-Up 1–7

Set up your terminal.

Configuration

As a minimum, determine the following menu items, and note
any change here that you make from the default value.
Menu item

Default

Terminal type
Emulation mode

VT320

Keyboard
Keyboard language

English

Communication
Port select

S1=comm1
print=comm2.

Communication
Word size

8 bits

Communication
Parity

None

Communication
Transmit speed

Communication
Receive speed
Printer
type

9600 baud

Printer

Transmit
speed
ANSI1

1 American National Standards Institute

1–8 Installation and Set-Up

Modification

Save your settings.

Save your settings.
Select the Save settings menu item, then press Enter or Return .
Caution
If you disable the Screen Saver feature, an image may
etch onto the screen, which may shorten the terminal’s
useful life.

Restore the
settings.

To recall the settings that you stored in memory using the Save
Settings menu item, select the Restore settings menu item
and press Enter or Return .
Note
Restore factory defaults is a selection included in the
Action menu.

Exit the Set-Up
menu.

To exit Set-Up, select the Exit Set-Up menu item or perform the
following procedure:
On a . . .

Press . . .

ANSI-style keyboard

PC keyboard

Caps Lock

Print Screen

Installation and Set-Up 1–9

2
Desktop Features
Invoking Desktop Features
Overview

From the Actions menu, you can invoke the Clock, Calculator,
Show character sets and Banner message features. When
the feature is highlighted (displayed in reverse video), press
Enter or Return to enable the feature.

MA−0031−93.GRA

While these desktop features are enabled, other terminal
functions are disabled. Press Ctrl Z , F10 , Exit , or Esc to exit the
feature.

Desktop Features

2–1

Invoking Desktop Features

Clock feature

You can enable the Clock feature without entering Set-Up by
pressing Caps Lock Alt F11 if you are not in an ASCII emulation
mode.
The current time is displayed in the status line if this feature
is enabled. The format is HH:MM, followed by AM or PM if the
12-hour format is selected. Use the following keys within the
clock feature:
Key

Function

or Tab

Go to next field.

or Shift Tab

Go to previous field.

Move within a field.

Return

or Enter

If desired, check the 24-hour format
box. For example, before entering
13:00, enable 24-hour format.

For 12-hour format, set the time to
morning by pressing A or P for
afternoon.

If the clock feature is enabled, then the alarm sounds for five
seconds or until a key is pressed. Each alarm message can be up
to 20 characters and will be displayed in the status line until a
key is pressed. If the hourly chime is enabled, then the terminal
will beep once every hour. In Set-Up, select the Save settings
menu item to save the time format. The clock feature is disabled
when the terminal is turned off.

2–2 Desktop Features

Invoking Desktop Features

Calculator
feature

You can enable the Calculator feature without entering
Set-Up by pressing Caps Lock Alt F12 , if you are not in an ASCII
emulation mode.
In addition to the numbers on the numeric keypad, you can use
the following keys with the calculator:
Key

Function

H , O , or D

Selects hexadecimal
decimal D format.

Arrow keys

Move the position of the calculator on
the screen.

Shift

Changes the keypad display to allow
selecting STO , RCL , 1/x , X² , and
Insert Result .

Alt

Changes the keypad display to
hexadecimal and allows selecting
keys A through F on the numeric
keypad.

C/E

Clears the entry.

STO

Stores the number in the display into
memory.

RCL

Recalls the number from memory and
places it in the display.

Shift Enter

Inserts the result at the current cursor
position after exiting the calculator
feature.

H , octal O , or

All calculator
math operations have equal priority except
 2
and . If a result is wider than the display, then a rounded
number will be displayed. The non-rounded result will continue
to be used in subsequent calculations. The decimal point cannot
be used with the hexadecimal mode.

Desktop Features

2–3

Invoking Desktop Features

Show Character
Sets feature

You can enable the Show character sets desktop feature
without entering Set-Up by using Caps Lock Alt F10 if you are
not in an ASCII emulation mode. When the character set is
displayed, you can use the following keys with this feature:
Key

Function

Next or Prev
Page Up or Page Down

Looks through the available character
sets.

Shift

Displays the line drawing character
set, if you are using a VT character
set.

Shift

Displays the technical character set.
For the current character set, inserts
the highlighted character into text at
the current cursor position, if you are
using a VT character set.

Shift Enter

Banner
message

From the Actions menu, select Banner message....
1. Press Return or Enter to display a dialog box.
2. Enter your banner message.
3. Press the

to select the

button.

4. Press Return or Enter to return to the Set-Up menu.

2–4 Desktop Features

3
Maintenance and Troubleshooting
Cleaning your Video Terminal
Cleaning the
Screen

Before cleaning the screen, set the terminal power switch to the
off position and wait 20 seconds to let static electricity dissipate.
Clean the screen with a video screen cleaner.

Cleaning the
Keyboard

If needed, wipe the keys with a soft cloth. Do not allow moisture
to get under the keys.

Troubleshooting
Identifying and
Correcting
Problems

The following can be sources of problems:
•

Communications cables

•

Host system

•

Nearby power or electrical sources

Maintenance and Troubleshooting 3–1

Troubleshooting

Troubleshooting
Table

Use Table 3–1 to identify and correct any problem areas.

Table 3–1 Identifying and Correcting Problems
Symptom

Possible Cause

Suggested Solution

Video display has
moving dots and
distorted lines. The
display rolls or
flickers.

There is
electromagnetic
interference.

Move any electromechanical device,
such as a fan or a motor, away from the
terminal or move the terminal.
CAUTION: Before moving the
system, turn the power off and wait
20 seconds to let static electricity
dissipate.

Refresh rate is too
low.

From the Display menu item, choose
Refresh rate and select 72 Hz.

The terminal is
faulty.

Set the power switch to the off position
and contact your service representative.

The printer is off.

Turn on the power to the printer.

There is a paper
jam.

Check the printer supplies: paper, toner,
or ribbon.

The printer cables
are not connected.

Check the cables.

Communication port
is not set correctly.

From the Communication menu
item, choose Port select and match
the setting to the connections on the
terminal.

If you have a
serial printer, its
speed may be set
incorrectly.

From the Printer menu item, choose
Serial print speed and match the
setting to the one in your printer
manual.

Accessibility aid is
enabled.

Check keyboard indicator line for icon.
This feature is enabled by pressing any
modifier key five times. To disable, press
and hold a modifier key and then press
another key.

The printer will not
print.

Modifier keys
remain in effect
after released.

Maintenance and Troubleshooting 3–3

Installing the ROM Cartridge

Installing the ROM Cartridge
Introduction

The terminal can accommodate an optional ROM cartridge at
the back of the terminal. This ROM cartridge will completely
replace the factory-installed software within the terminal for
new software versions or special applications.
When an option ROM is not used, the ROM cartridge holder is
empty with a cover over it.

Installing and
Removing the
ROM Cartridge

To install a ROM cartridge:
1. Set the power switch to the off position.
2. Remove the cover by lifting it from the bottom and gently
pulling it straight back.
3. Plug in a ROM cartridge with its attached cover
the cover.

, and close

If you are having the terminal serviced, then remove and
save the ROM cartridge. To remove a ROM cartridge, lift its
cover from the bottom and gently pull it straight back.

Disposing of your Terminal
Warning
If you need to dispose of your terminal, ask a qualified
service representative for the proper disposal procedures.
Improper disposal could result in personal injury.

3–4 Maintenance and Troubleshooting

4
Defining Keys
Define Key Editor
Overview

The terminal provides a powerful Define Key Editor that allows
you to modify the function of keys on your keyboard. Since
keystrokes can perform many different functions, it will take
some practice to understand how the keys work. This section is
an introduction to customizing your keyboard.

Moving
Standard
Functions

The simplest way to re-program a key is to copy the behavior
of another key. This method allows you to move factory default
key functions to any position on the keyboard. To move factory
default key functions:
1. From the Keyboard menu item, select the Define
key . . . function, and press Return . The Define Key
Editor menu will appear.
2. Press the key for which you want to assign a new behavior.
3. Press the
key to highlight the "Copy of key default" radio
button ( Copy of key default) and press Enter .

4. Press the key whose factory default behavior is what you
want your defined key to do.
5. Press the
key to highlight the OK or Apply pushbutton
and press Enter .

Defining Keys 4–1

Define Key Editor

Customization

If you want to program a key to behave differently than one of
the factory defined keys, then you will need to know about the
following key categories:
Function:

Keys used to transmit function key sequences
or to perform local terminal functions such as
the arrow keys ( , , , ), the Shift modifier
key, or the Set-Up key.

Alphanumeric:

Modifier Keys

Keys used to transmit alphanumeric
characters.

Modifier keys vary from within the function and alphanumeric
categories. A modifier key is a key that modifies the behavior
of other keys when it is pressed and held down. For example,
pressing an alphanumeric key in combination with the Shift
modifier key will normally send the shifted or uppercase
characters for that key.
Modifier keys are treated as a special kind of local terminal
function. The function modifier keys are: Shift , Ctrl , and Alt .
Alphanumeric keys can also be modified by pressing Group Shift
( Alt Gr on enhanced PC keyboards) and Alt Shift (Shift-2). Modifier
keys themselves cannot normally be modified by other keys. A
key assigned to act as the Shift modifier, for example, cannot
transmit a function sequence when pressed in combination with
the Alt key. Defining a key as a modifier key makes all assignable
combinations of that key act as a modifier.

Creating a New
Function

To define a new function key:
1. From the Keyboard menu item, select the Define
key . . . function, and press Return . The Define Key
Editor menu will appear.
2. Press the key for which you want to assign a new behavior.
3. Press the
and
keys to highlight the "Function" radio
button ( Function) and press Enter .

4. Press the
and
keys to highlight the modifier
combination that you want to define (unshifted, shifted,
control, and so on) and press Enter .

5. Press the
key to move to the "Select function" scroll box.
Press the
and
keys to highlight the desired keystroke
function from the list and press Enter .

4–2 Defining Keys

Define Key Editor

6. Press the

key to return to the modifier selection.

7. Repeat steps 4 through 6 to define other modifier
combinations as desired.
8. Use the arrow keys ( , , ,
pushbutton and press Enter .

) to highlight the OK or Apply

Correcting a
Mistake

If you make a mistake or want to start over, select the Cancel
pushbutton or select the Exit Set-Up menu item. Your
changes will not be recognized until you select the OK or Apply
pushbutton. To save your key definitions so they will be available
the next time you turn on the system power, select the Save key
definitions menu item from the Keyboard menu.

Examples of
Uses

Examples of when to create new functions include:
•

To change the < x key to delete when unshifted and to
backspace when shifted

•

To disable the Compose , Break , or Set-Up key by assigning
them to have no function

The Define Key Editor can be very powerful if you take the time
to learn how to use it. No matter how you redefine the keys,
you can always enter Set-Up by pressing F3 after powering on.
Additionally, you can always restore the factory default settings
by invoking the Actions menu item.
Note
See the Video Terminal Programmer Information manual
to redefine alphanumeric keys or keyboard layouts.

Defining Keys 4–3

A
Specifications

Video Terminal

The following are the specifications for the video terminal.
Dimensions
Height

32 cm (12.6 in)

Width

31.5 cm (12.4 in)

Depth

33 cm (13 in)

Weight

7.9 kg (17.4 lb)

Tilt Range

25° (5° forward, 20° backward)

Swivel Range

± 90° (left and right)

Display
Cathode ray tube
(CRT)

35 cm (14 in) diagonal antiglare
flat-profile screen

Overscan

60 Hz - 16
font

Area

800

Usable area

17 cm (6.7 in)
aspect ratio

No. of lines

25, 42, or 53 data lines

Page size

Selectable 24, 25, 36, 42, 48, 50, and
72 lines (emulation dependent)

10 font; 72 Hz - 13

432 pixels with 88 DPI density
23 cm (9 in); 1:1.4

Operating Systems
Supported

MDOS, OpenVMS, OSF, ULTRIX,
UNIX, VMS, or any other that
supports ASCII or ANSI protocols.

Terminal Emulations

ANSI, PCTerm, and ASCII
emulations: ADDS, TVI, VT, WYSE,
or SCO console.

Specifications A–1

Specifications

Character Set
Support

Multiple languages using ISO and
IBM code pages; Set-Up selectable in
five languages.

Productivity
Features

Local copy and paste
Time-of-day clock—sound alarms and
display messages
Desktop calculator—insert result into
text
Show character sets—insert character
into text

ROM cartridge
support

4-Mbit (512 K byte) customerinstallable ROM cartridge at back
of system unit that completely
replaces the factory-installed ROM
code for new versions of the terminal’s
firmware.

Electrical
Requirements
AC input voltage

120 Vac only; 101, 110, 120, 220, 230,
240 auto-sensing (product variant)
single phase, 3-wire

Line frequency

47 Hz to 63 Hz

Power consumption

40 watts maximum

Operating
Temperature

10°C to 40°C (50°F to 104°F)

Humidity

10% to 90% relative humidity
Maximum wet bulb = 28°C
Minimum dew point = 2°C
(noncondensing)

A–2 Specifications

Specifications

Keyboard

The following are the specifications for the keyboard.
Keyboard style

Cables

LK411/LK412 for ANSI style layout;
PCXAL for enhanced PC 101/102 style
layout; available for most European
languages.

Protocol

IBM enhanced PS/2-compatible

Connector

PS/2-style, 6-pin mini DIN

Keyboard keys

All keys are programmable for single
characters, character sequences, or
local functions.

Nonvolatile memory

768K bytes memory
User-defined key maximum
length = 255 bytes.

EIA-232 maximum cable length is 15.3 m (50 ft);
EIA-423 maximum cable length is 305 m (1000 ft).

Communication/Printer
Ports
Serial

Parallel

Bidirectional serial communication/printer ports
with full modem support at 300 to 115.2K baud:
EIA 232

EIA 423

Comm 1 (Figure A–1):
Two 25-pin D-sub m/f
(use one or the other)

Comm 2
(Figure A–2):
6-pin MMJ

Centronics (25-pin D-sub f) parallel printer
connector (Figure A–3).

m = male; f = female

Specifications A–3

Specifications

Figure A–1 Comm1—Serial Communication/Printer Ports1

CCITT/EIA/DIN
1
1 GND / NC
2 TXD
103/BA/D1
3 RXD
104/BB/D2
4 RTS
105/CA/S2
5 CTS
106/CB/M2
6 DSR
107/CC/M1
7 SIG GND
102/AB/E2
8 CD
109/CF/M5
12 SI
112/CI
20 DTR
108.2/CD/S1.2
23 SPD SEL
111/CH/S4
9−11, 13−19, 21, 22, 24, 25 NC
MA−0019−93.GRA

Figure A–2 Comm2—MMJ Port

1 DTR
2 TXD +
3 TXD −
4 RXD −
5 RXD +
6 DSR

MA−0020−93.GRA

Figure A–3 Parallel Printer Port
1
14

A–4 Specifications

1 STROBE L
2 DAT <0>
3 DAT <1>
4 DAT <2>
5 DAT <3>
6 DAT <4>
7 DAT <5>
8 DAT <6>
9 DAT <7>

10 ACKNLG L
11 BUSY
12 PE
13 SLCT
14 AUTO FEED XT L
15 ERROR L
16 INIT L
17 SLCT IN L
18 − 25 GND
MA−0018−93.GRA

Pin 1 is ground on the VGB11. NC = Not connected.

Specifications

Acoustic Noise

Preliminary declared values per ISO 9296 and ISO 7779:

Product1

Sound Power Level
L  , B
Idle
Operate

Sound Pressure Level2
L  , dBA
Idle
Operate

VGB11

<3.9

<22

PCXAL

6.0

PC7XL

5.3

LK411

5.6

1 1 B = 10 dBA.

2 Operator position.

Table A–1 Standards Conformance and Approvals
Agency

Type

Standard

Subject

CSA

Safety

CSA 22.2 #950 M1989

Safety of Information Technology
Equipment Including Electrical
Business Equipment (Canada)

CSA 22.1

Canadian electrical code

CISPR-22

EMI/FRI

CISPR-22 Class A

Electromagnetic compatibility

EIA

Telcom

EIA 423
EIA 232-E

Serial communications

DOC Canada

EMI/RFI

CSA 108.8

North American Class A version

FCC

EMI/RFI

FCC part 15
Class B

Electromagnetic compatibility

Australia
PTT
German PTT
Japan PTT
Sweden PTT

Telcom

CCITT V.24 and V.28

Serial communications

Australia

Safety

AS3260

Australia product safety
(continued on next page)

Specifications A–5

Specifications

Table A–1 (Cont.) Standards Conformance and Approvals
Agency

Type

Standard

Subject

TUV

Safety

EN60950 (2nd ed,
1988)
EN60950 (Amd 1 & 2,
1990)
IEC950 (2nd ed, 1991)
German X-Ray Act
RöV §5(2)
EMKO-TSE (74-SEC)
203/92
SS 436 14 90, MPR II

Safety of Information Technology
Equipment Including Electrical
Business Equipment
GS-Mark (Geprüfte Sicherheit)

TUV

Ergonomic

ISO/DIS 9241-3

VDT Ergonomic Requirements

Safety

UL 544 (2nd ed)

Standard for Medical and Dental
Equipment

UL 1950 (1st ed)

Safety of Information Technology
Equipment Including Electrical
Business Equipment

NFPA 70

U.S. National Fire Protection
Agency - National Electrical Code

VDE

EMI/RFI

Vfg 243/1991
EN55022 class B

Radio Protection Mark

VCCI
(Japan)

EMI/RFI

Class 1

Electromagnetic compatibility

A–6 Specifications

Specifications

Flame
Retardants

The thermoplastic enclosures do not contain polybrominated
diphenylether (PBDE) as a flame retardant additive; therefore,
they do not emit toxic dibenzofuran and dibenzodioxin gases.

PVC

The plastic enclosures are not made of rigid PVC. The material
has a non-halogenated, flame-retardant system and is cadmium
free.

Asbestos

Asbestos is not used in this product or in its manufacturing
process.

Ozone
Depleting
Substance

The VGB11 is in full compliance with the labeling requirements
in the U.S. Clean Air Act Amendments of 1990. It does not
contain, nor is it manufactured with, a Class 1 ODS, as defined
in Title VI Section 611 of this act.

Specifications A–7

B
Keyboard Function Keys
User Definable Keys
Overview

All keyboard keys are programmable by selecting the Define
key function from the Keyboard menu item in Set-Up. They
can be programmed to send single characters or character
sequences, or to invoke a local function, such as Print Screen.
The function keys have the following key levels: Unshifted,
Shifted, Control, Shift Control, Alt, Alt-Shift, Alt-Control, and
Alt-Shift-Control.

Local Functions
Overview

The keys used to perform local terminal functions differ between
the keyboards and the mode selection. Table B–1 shows the
corresponding keys for the default local functions and their
function number. This number is used in the program function
key host sequence to specify a change to that Local Function key.
Table B–2 lists other available local functions.

Keyboard Function Keys

B–1

Local Functions

Table B–1 Local Functions
Function
Number Function

ANSIStyle
Keyboard

SCO
Console

PC
Keyboard
ANSI-Style

PC
Keyboard
PC-Style

PC
Keyboard
SCO

no function

Hold

Lock F1

Scroll Lock

Lock F2

Print Screen

Set-Up

Lock F3

Lock Print Screen
Lock Sys Rq

Alt Print Screen

Break

Lock F5

Lock Pause

Hard Reset

Ctrl F3

Lock Ctrl F3

Ctrl F3

Ctrl Lock Print Screen

Toggle
Autoprint

Ctrl F2

Lock Ctrl F2

Ctrl F2

Ctrl Print Screen

Disconnect

Shift F5

Lock Shift F5

Shift F5

Shift Lock Pause

Send
Answerback

Ctrl F5

Lock Ctrl F5

Ctrl F5

Ctrl Lock Pause

Print Composed
Main Display

Shift F2

Shift
Print Screen

Pan Up

Ctrl

Pan Down

Ctrl

Pan Prev Page

Ctrl Prev

Ctrl Page Up

Pan Next Page

Ctrl Next

Ctrl Page Down

Copy & Paste
Mode

F1 (hold
down)

Caps Lock F1 F1

C&P Cursor
Left

Ctrl

Scroll Lock

1 X means the function is not available in the default SCO state.

If there is no "X" in the SCO Console
column, then this means that the key sequence is the same as the ANSI-Style Keyboard column. If there
is no "X" in the PC Keyboard SCO column, then this means that the key sequence is the same as the PC
Keyboard PC-Style column.
± means the function switches alternately between on and off.
C&P means Copy and Paste.
Lock means the Lock key, Caps Lock key, or key with lock icon.

(continued on next page)

B–2 Keyboard Function Keys

Local Functions

Table B–1 (Cont.) Local Functions
Function
Number Function

ANSIStyle
Keyboard

SCO
Console

PC
Keyboard
PC-Style

PC
Keyboard
ANSI-Style

C&P Cursor
Down

C&P Cursor Up

C&P Cursor
Right

C&P Start
Selection

Select

Home

C&P Copy

Remove

End

C&P Paste

Insert Here

Insert

C&P ±
Left-to-Right

Select

Home

Shift Modifier

Left or right

Shift

Left or
right Shift

Ctrl

Left or right

Control Modifier

Ctrl

43
44
45

Left or
right Alt

Start Compose

Left or right

Left

Compose

Alt Space

Group Shift
Modifier

Group Shift

46†

Shift2 Modifier

Alt Shift

Primary KB
language

Ctrl Alt F1

Left or right

Left or
right Ctrl

Alt Function
Modifier

Alt

Alt Gr

Lock Alt Ctrl F1 Ctrl Alt F1

PC
Keyboard
SCO

Left or
right Alt

Alt Gr

Ctrl Alt F1

See SCO
Console

1 X means the function is not available in the default SCO state.

†The Shift2 Modifier is assigned to the Alt Shift key (German "right Compose ") when it appears on the
corresponding keyboard (German).
± means the function switches alternately between on and off.
C&P means Copy and Paste.
Lock means the Lock key, Caps Lock key, or key with lock icon.

(continued on next page)

Keyboard Function Keys

B–3

Local Functions

Table B–1 (Cont.) Local Functions
Function
Number Function

ANSIStyle
Keyboard

SCO
Console

Secondary KB
language

Ctrl Alt F2

Lock Alt Ctrl F2 Ctrl Alt F2

49‡

± KB language

± Caps Lock
State

± Num Lock
State

± ANSI/IBM
Style

Extend Kbd
Modifier

Screen saver

Calculator

Lock

PC
Keyboard
ANSI-Style

PC
Keyboard
PC-Style

PC
Keyboard
SCO

Ctrl Alt F2

See SCO
Console

Lock

Num Lock

Lock
Num Lock

Lock

Lock Alt F12

Clock

Lock Alt F11

Character table

Lock Alt F10

Transfer result

Shift
Enter

Shift Enter

‡Toggle KB language is assigned to the named language key when it appears on the corresponding keyboard
(Greek, Hebrew, and Russian).
± means the function switches alternately between on and off.
C&P means Copy and Paste.
Lock means the Lock key, Caps Lock key, or key with lock icon.

B–4 Keyboard Function Keys

Local Functions

Table B–2 Other Available Local Functions
Function
Number Function

Function
Number Function

120

Page 0

CAN

121

Page 1

ESC

122

Page 2

DEL

123

Page 3

100

UDK sequence

124

Page 4

105

Soft reset

125

Page 5

106

±Show controls

126

Page 6

111

±Status display

138

112

±Split screen

139

113

Raise horizontal split

142

Slow Scroll

114

Lower horizontal split

144

Fast Scroll

115

Adjust window to show cursor

151

±Keyclick

116

±Cursor drag

155

±Block mode

117

±Insert mode

156

Block mode on

119

Home & Clear

157

Block mode off
Note

An Accessibility aid feature allows the modifier keys to
remain in effect after they are released. A small icon in
the status line indicates its state.
To enable: Press any modifier key five times.
To disable: Press and hold a modifier key while you
press another key.

Keyboard Function Keys

B–5

C
Compose Characters
Compose Characters
The tables in this appendix describe how to compose characters
for the Multinational, ISO Latin 1, ISO Latin 2, ISO LatinGreek, and National Replacement character sets (NRCS) for a
ANSI-style keyboard.
In the tables,
column . . .

Represents . . .

Characters to be composed.
3-

Three-stroke key sequences beginning with
the Compose key.

Two-stroke key sequences beginning with a
non-spacing diacritical accent key.

Within the
tables . . .

Represents . . .

(sp)

A space character.

Canadian-English, Danish, Dutch, Hebrew, Hungarian, Italian,
Norwegian, Polish, Romanian, Russian, SCS, Turkish-F, TurkishQ, UK, and US keyboards do not have non-spacing diacritical
marks regardless of the character mode.

Compose Characters C–1

Compose Characters

Table C–1 Multinational Character Set
3-

[

((

]

))

{

}

‘

¨ (sp)

` (sp)

´ (sp)

^(sp)

~(sp)

LL=

YY=

CO
C0

XO
X0

//
/<

C/
C|

SO
S!

0^
° (sp)
* (sp)

´a

´A

~(sp)

° (sp)

(continued on next page)

C–2 Compose Characters

Compose Characters

Table C–1 (Cont.) Multinational Character Set
3-

¨a

¨A

a*
a°

A*
A°

´e

´E

¨e

¨E

´i

´I

¨i

¨I

´o

´O

¨o

¨O

´u

´U

¨u

¨U

¨y

¨y
(continued on next page)

Compose Characters C–3

Compose Characters

Table C–1 (Cont.) Multinational Character Set
Multinational Specific

´y

´Y

¨Y

Table C–2 ISO Latin (Latino, Latina) 1 Specific
3-

NBSP

(sp)(sp)

´´

||
#! ^

¨ (sp)
""

-D

-d

¨ (sp)

Table C–3 ISO Latin (Latino, Latina) 2
3-

¨a

¨A

¨e

¨E

¨o

¨O

u°

U°

´a

´A

´c

´C

[´]

(continued on next page)

C–4 Compose Characters

Compose Characters

Table C–3 (Cont.) ISO Latin (Latino, Latina) 2
3-

´e

´E

´i

´I

´l

´L

´n

´N

´o

´O

´r

´R

´s

´S

´u

´U

´y

´Y

´z

´Z

[ ]

Compose Characters C–5

Compose Characters

Table C–4 ISO Latin-Greek, Latino-Griego, Latin-Grec, Latina-Greca
3-

[¨]
¨

[! ]

¨!

C–6 Compose Characters

¨!

!
!

¨!

[¨] + [! ]

!
!

Compose Characters

Table C–5 National Replacement Character Sets (NRCS)
Canadien
(Français)

´e

Danish

Español

~ (sp)

LL=

os
! s

´e

Finnish

Français, Belgian, UK

LL=

(continued on next page)

Compose Characters C–7

Compose Characters

Table C–5 (Cont.) National Replacement Character Sets (NRCS)
Italiano

(sp) *
(sp) 0

Norwegian

Portuguese

´ (sp)

^ (sp)

` (sp)

´ (sp)

~ (sp)

Swedish

´e

´E

Suisse/Français, Schweizerisch/Deutsch

C–8 Compose Characters