Digital PDFs

EK-V411A-CG-A01

May 1994

94 pages

Original

2.8MB

Document:	VAX 4000 Model 100/100A Upgrade to Model 105A
Order Number:	EK-V411A-CG
Revision:	A01
Pages:	94
Original Filename:

OCR Text

VAX 4000
Model 100/100A Upgrade
to Model 105A
Order Number: EK–V411A–CG. A01

May 1994

Digital Equipment Corporation
Maynard, Massachusetts

May 1994
Digital Equipment Corporation makes no representations that the use of its products in the
manner described in this publication will not infringe on existing or future patent rights, nor do
the descriptions contained in this publication imply the granting of licenses to make, use, or sell
equipment or software in accordance with the description.
Possession, use, or copying of the software described in this publication is authorized only
pursuant to a valid written license from Digital or an authorized sublicensor.
© Digital Equipment Corporation 1994. All Rights Reserved.
The postpaid Reader’s Comments forms at the end of this document request your critical
evaluation to assist in preparing future documentation.
The following are trademarks of Digital Equipment Corporation: DEC, Digital, ThinWire, VAX,
VAX DOCUMENT, VMS, and the DIGITAL logo.
All other trademarks and registered trademarks are the property of their respective holders.
S2573

This document was prepared using VAX DOCUMENT Version 2.1.

Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

vii

1 Overview of the Conversion Process
1.1
1.2

In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview of the Conversion Processes . . . . . . . . . . . . . . . . . . . . .

1–1
1–1

2 Upgrading the VAX 4000 Model 100 System
2.1
2.2
2.3
2.4
2.5

In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedure Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unpacking the Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upgrading the VMS Operating System . . . . . . . . . . . . . . . . . . . .
Replacing the CPU Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2–1
2–1
2–2
2–3
2–4

3 Upgrading the VAX 4000 Model 100A System
3.1
3.2
3.3
3.4
3.5

In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedure Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unpacking the Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before Installing the Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the CPU Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3–1
3–1
3–2
3–3
3–4

A Mandatory Return Procedure and Forms
A.1
A.2

Return Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Return Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A–1
A–2

iii

Figures
2–1
2–2
2–3
2–4
2–5
2–6
2–7
2–8
2–9
2–10
2–11
2–12
2–13
2–14
2–15
2–16
2–17
2–18
2–19
2–20
2–21
2–22
2–23
2–24
2–25
2–26
2–27
2–28
2–29
2–30
2–31
3–1
3–2
3–3
iv

Disconnecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . .
Disconnecting the External Cables/Terminators from the Port
Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Enclosure Cover . . . . . . . . . . . . . . . . . . . . . . .
Unscrewing the Drive Shelves . . . . . . . . . . . . . . . . . . . . . . . .
Disconnecting the Internal Power Cables . . . . . . . . . . . . . . . .
Disconnecting Internal DSSI Connectors . . . . . . . . . . . . . . . .
Removing a SIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disconnecting the Internal SCSI Cable from the CPU
Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sliding the Drive Mounting Shelves Forward . . . . . . . . . . . .
Lifting the Drive Mounting Shelves Upward . . . . . . . . . . . . .
Removing the DSSI Daughter Card . . . . . . . . . . . . . . . . . . . .
Disconnecting the Q–bus and external SCSI Cables . . . . . . .
Removing the Port Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing Connectors from the Port Cover . . . . . . . . . . . . . .
Installing the Alignment Pins on the Port Cover . . . . . . . . . .
Installing the Original DSSI Cable on the Port Cover . . . . . .
Installing the Q–bus Cable on the Port Cover . . . . . . . . . . . .
Installing the Blank Covers on the Port Cover . . . . . . . . . . .
Installing the SCSI Cable on the Port Cover . . . . . . . . . . . . .
Installing the Port Cover and Cables . . . . . . . . . . . . . . . . . . .
Removing the CPU Module . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the DSSI Daughter Card . . . . . . . . . . . . . . . . . . . .
Connecting the External SCSI Cable to the CPU Module . . .
Connecting the Single DSSI Cable to the Daughter Card . . .
Connecting the Q–bus Cable to the CPU Module . . . . . . . . . .
Aligning the Drive Mounting Shelves . . . . . . . . . . . . . . . . . .
Reinstalling the Drive Mounting Shelves . . . . . . . . . . . . . . . .
Securing the Drive Mounting Shelves . . . . . . . . . . . . . . . . . .
Installing a SIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reconnecting Cables and Terminators . . . . . . . . . . . . . . . . . .
Applying the New Medallion . . . . . . . . . . . . . . . . . . . . . . . . .
Disconnecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Enclosure Cover . . . . . . . . . . . . . . . . . . . . . . .
Unscrewing the Drive Shelves . . . . . . . . . . . . . . . . . . . . . . . .

2–4
2–5
2–6
2–7
2–9
2–10
2–11
2–12
2–13
2–14
2–15
2–16
2–17
2–18
2–19
2–20
2–21
2–22
2–23
2–24
2–26
2–28
2–29
2–30
2–31
2–32
2–33
2–34
2–36
2–37
2–38
3–4
3–5
3–6

3–4
3–5
3–6
3–7
3–8
3–9
3–10
3–11
3–12
3–13
3–14
3–15
3–16
3–17
3–18
3–19
3–20
3–21

Disconnecting the Internal Power Cables . . . . . . . . . . . . . . . .
Disconnecting Internal DSSI Connectors . . . . . . . . . . . . . . . .
Removing a SIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disconnecting the Internal SCSI Cable from the CPU
Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sliding the Drive Mounting Shelves Forward . . . . . . . . . . . .
Lifting the Drive Mounting Shelves Upward . . . . . . . . . . . . .
Removing the DSSI Daughter Card . . . . . . . . . . . . . . . . . . . .
Disconnecting the Q–bus and external SCSI Cables . . . . . . .
Removing the CPU Module . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the DSSI Daughter Card . . . . . . . . . . . . . . . . . . . .
Connecting the External SCSI Cable to the CPU Module . . .
Connecting the Single DSSI Cable to the Daughter Card . . .
Connecting the Q–bus Cable to the CPU Module . . . . . . . . . .
Aligning the Drive Mounting Shelves . . . . . . . . . . . . . . . . . .
Reinstalling the Drive Mounting Shelves . . . . . . . . . . . . . . . .
Securing the Drive Mounting Shelves . . . . . . . . . . . . . . . . . .
Installing a Memory Module . . . . . . . . . . . . . . . . . . . . . . . . .
Applying the New Medallion . . . . . . . . . . . . . . . . . . . . . . . . .

3–8
3–9
3–10

Contents of the 53XR–AA Upgrade Kit . . . . . . . . . . . . . . . . .
Contents of the 53XR–AA Upgrade Kit . . . . . . . . . . . . . . . . .

2–3
3–3

3–11
3–12
3–13
3–14
3–15
3–17
3–19
3–20
3–21
3–22
3–23
3–24
3–25
3–27
3–28

Tables
2–1
3–1

Preface
This manual describes how to upgrade a VAX 4000 Model 100 or a VAX 4000
Model 100A system to a VAX 4000 Model 105A by replacing the KA52 CPU
module with a KA53 Module.

Intended Audience
This document is intended for Digital Services personnel and licensed
self-maintenance customers.

Customer Responsibilities
Only qualified maintenance personnel (Digital Services representatives
or qualified self-maintenance customers) should perform the installation
procedure.
If you are not a qualified self-maintenance customer, call Digital Services to
schedule a system conversion. It is your responsibility to perform a software
backup before a Digital Services representative arrives at your site.
When the conversion is complete, return the original CPU module to Digital.
Appendix A contains forms that need to be completed by the Digital Services
representative and signed by both you and the Digital Services representative.

Digital Services Responsibilities
Before arriving at the site, contact the customer to ensure that the customer’s
software is backed up before arriving at the site.
After installation of the upgrade kit, the you must complete the forms in
Appendix A and remove them from this document. The forms must be signed
by both you and the customer.

vii

The following forms are in Appendix A:
•

Digital Services Worksheet

•

Installation Receipt–Customer Copy

•

Installation Receipt–Digital Services Copy

•

Returned Material Checklist

You should give the customer the signed Installation Receipt–Customer Copy.
Include the signed Installation Receipt–Digital Services Copy with the CPU
module that is being returned to Digital to ensure that the customer receives
credit.

Organization
This document contains three chapters and one appendix:
•

Chapter 1 contains an overview of the upgrade process.

•

Chapter 2 provides detailed upgrade conversion procedures for a VAX 4000
Model 100.

•

Chapter 3 provides detailed upgrade conversion procedures for a VAX 4000
Model 100A.

•

Appendix A contains forms for the return of the original CPU module.

Conventions
The following conventions are used in this guide:

viii

Convention

Description

A lowercase italic x indicates the generic use of a letter. For
example, xxx indicates any combination of three alphabetic
characters.

italic type

Italic type emphasizes important information or indicates
variables. It is also used for the titles of manuals.

Note

A note contains information that is of special importance to the
user.

Caution

A caution contains information to prevent damage to the
equipment.

Related Documents
The following list contains related documents:
Documentation

Order Number

VAX 4000 Model 105A Installation Information

EK–512AA–IN

VAX 4000 Model 105A Operator Information

EK–513AA–OP

VAX 4000 Model 105A Customer Technical Information

EK–514AA–TI

VAX 4000 Model 105A Troubleshooting and Diagnostics
Information

EK–515AA–TS

1
Overview of the Conversion Process
1.1 In This Chapter
This chapter describes the general process for upgrading a VAX 4000
Model 100 or Model 100A to a VAX 4000 Model 105A system by replacing
the KA52 CPU module with a KA53 CPU module.

1.2 Overview of the Conversion Processes
Tasks required to upgrade VAX 4000 models are summarized below. To begin
the actual conversion, turn to Chapter 2 for the conversion of a VAX 4000
Model 100, or Chapter 3 for the conversion of a VAX 4000 Model 100A.
The VAX 4000 Model 100A is identical to the VAX 4000 Model 100, except that
the port cover is designed to accomodate a dual DSSI port.
The conversion of a VAX 4000 Model 100A to Model 105A involves replacing
the CPU module and the system medallion. These procedures are described in
detail in Chapter 3.
The conversion of a VAX 4000 Model 100 to Model 105A includes upgrading
with a new port cover (as if it were being converted first to a Model 100A),
then replacing the CPU module and the system medallion. These procedures
are described in detail in Chapter 2.

Overview of the Conversion Process 1–1

2
Upgrading the VAX 4000 Model 100
System
2.1 In This Chapter
This chapter lists detailed step-by-step procedures for upgrading a VAX 4000
Model 100 system to a Model 105A.

2.2 Procedure Overview
The conversion procedure is summarized next. To begin the actual conversion,
turn to Section 2.3.
1. Have the customer back up the system software.
2. Unpack and verify the conversion kit.
3. Upgrade the VMS disk 5.5-2H4 (VMS 6.1 is acceptible).
4. Shut down the operating system.
5. Turn off the system power and remove the power cord.
6. Disconnect all external cables.
7. Remove the enclosure cover.
8. Remove the memory SIMMs (memory modules).
9. Remove the upper and lower drive mounting shelves.
10. Disconnect and remove the DSSI daughter card.
11. Disconnect all internal cables from the port cover to the CPU module,
daughter cards and the drives.
12. Remove the present port cover with attached cables.
13. Remove all attached cables from the present port cover for use on the new
one.

Upgrading the VAX 4000 Model 100 System 2–1

Upgrading the VAX 4000 Model 100 System
2.2 Procedure Overview
14. Install the alignment pins with washers on the new port cover.
15. Install the internal cables on the new port cover.
16. Install the new port cover with its connectors onto the rear of the system
box, feeding the cables through the cutouts in the system box.
17. Remove the CPU module.
18. Install the new CPU module.
19. Connect all cables to the CPU module and daughter cards.
20. Reinstall the upper and lower drive mounting shelves in the system box,
and connect the internal SCSI cable to the CPU module.
21. Reinstall the SIMMs.
22. Reinstall the enclosure cover.
23. Connect the power cable, signal cables, and terminators to the system as
desired.
24. Remove the system medallion and install the new one.
25. Have the customer reinstall system data (if necessary).
26. Fill out the forms in Appendix A.
27. Return the original CPU module as instructed (see Appendix A).

2.3 Unpacking the Kit
Unpack the kit as follows:
1. Make sure there is no external damage to the shipping container, such as
dents, holes, or crushed corners.
2. Unpack the conversion kit and check its contents against the shipping
invoice. Table 2–1 lists the kit contents for the Model 100/100A to Model
105A upgrade, 53XR–AA. Other items may be present, but are not required
for this conversion.

2–2 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.3 Unpacking the Kit
CAUTION
Static discharge can damage modules. Use an antistatic wrist strap
and antistatic mat during handling. The wrist strap and mat are in
the antistatic kit in the Digital Services toolkit.

3. Unpack the KA53 CPU module and place it on a grounded antistatic mat.
4. Save the packing material, and use it to return the original CPU module.
5. If any item is missing or damaged:
•

Contact the customer’s sales representative.

•

Contact the customer’s delivery agent.

Table 2–1 Contents of the 53XR–AA Upgrade Kit
Description

Part Number

Quantity

Wire harness assy

17–03615–001

Product conversion label

36–15946–00

Regulatory label

36–30382–23(24)

NVAX CPU

54–21797–02

Medallion

74–37642–32

DSSI blank panel

74–46956–01

Expansion port cover

74–46957–01

Machine screw, 8mm

90–10917–01

VAX 4000 Model 100/100A
Upgrade to Model 105A

EK–V411A–CG

VMS multimedia Viking

QA–001AA–UW

Model 105A doc set

QZ–K04AB–GZ

2.4 Upgrading the VMS Operating System
If you do not have VMS operating system version 6.1 on your system, it is
necessary to upgrade it before installing the hardware by following these steps:
1. Have the customer back up the system software before the Digital Services
representative arrives. It is the customer’s responsibility to back up the
system software.
2. Power up the system and run diagnostics to verify system operation.

Upgrading the VAX 4000 Model 100 System 2–3

Upgrading the VAX 4000 Model 100 System
2.4 Upgrading the VMS Operating System
3. Upgrade the VMS disk 5.5-2H4.
4. Shut down the operating system in the proper manner.
5. Turn off the system power before installing the kit.

2.5 Replacing the CPU Module
To replace the CPU module:
1. Disconnect the power cord from the wall outlet, then from the system (see
Figure 2–1).
Figure 2–1 Disconnecting the Power Cord

MLO-010799

Power cord

2–4 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
2. Disconnect all the external cables or terminators from the present port
cover, and save the screws (see Figure 2–2).
Figure 2–2 Disconnecting the External Cables/Terminators from the Port
Cover
1

4
MLO-010800

Q–bus ports (Q–bus cables may be attached)
DSSI terminator or cable
SCSI terminator or cable

Ethernet connector

Upgrading the VAX 4000 Model 100 System 2–5

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
3. Remove the enclosure cover by removing the two screws at the rear of the
system box and sliding it forward (see Figure 2–3).
Figure 2–3 Removing the Enclosure Cover
2

1
MLO-010801

Screws
Enclosure cover

2–6 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
4. Remove the upper and lower drive mounting shelves together as a single
unit (it is not necessary to disassemble the shelves themselves). Unscrew
all six screws from the shelves, leaving the topmost captive screw until
last for support. Leave the captive screws in position and save the Phillips
screws for reinstallation of the shelves (see Figure 2–4).
Figure 2–4 Unscrewing the Drive Shelves

3
2

MLO-010802

Topmost captive screw
Other captive screws

Phillips screws

Upgrading the VAX 4000 Model 100 System 2–7

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
5. Disconnect the internal power cables from the power supply (Figure 2–5).
6. Disconnect the pigtailed, 2-pin DSSI power cable from the CPU module.
(Figure 2–5).
Note
Some VAX 4000 Model 100s do not have the pigtailed power cable, and
you may skip this step in that case.

2–8 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
Figure 2–5 Disconnecting the Internal Power Cables

MLO-012287

Internal power cable
Internal power cable with pigtailed DSSI power cable

CPU module DSSI power cable connector

Upgrading the VAX 4000 Model 100 System 2–9

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
7. Disconnect the internal DSSI connectors from all drives mounted on the
shelves. It is not necessary to disconnect the power cable from each drive.
Figure 2–6 shows one drive as an example.
Figure 2–6 Disconnecting Internal DSSI Connectors

MLO-010804

Internal DSSI connectors
8. Remove all SIMMs from the CPU module. (See Figure 2–7).
Caution
Static electricity can damage integrated circuits. Wear a wrist strap
and place an antistatic mat under the system unit when working with
the internal parts of the system unit.

Note
Note carefully the position of each SIMM you remove; they must be
reinstalled later into the same slots.
Beginning with the SIMMs closest to the front of the enclosure remove
each as follows:
1. Release the memory module by pressing the metal board clips on the
memory module connector away from the center.
2. Tip the memory module rearward.

2–10 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
3. Lift the memory module up and out of the enclosure, and place it on an
anti-static mat.
Figure 2–7 Removing a SIMM

Metal Board Clip

MS44 Memory Modules

MLO-009876

Upgrading the VAX 4000 Model 100 System 2–11

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module

9. Disconnect the internal SCSI cable from the CPU module (see Figure 2–8).
Figure 2–8 Disconnecting the Internal SCSI Cable from the CPU Module

MLO-012288

Internal SCSI cable

2–12 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
10. Remove the shelves by sliding them forward (see Figure 2–9) and lifting
them up from the enclosure (see Figure 2–10).
Figure 2–9 Sliding the Drive Mounting Shelves Forward
1

MLO-010806

Drive mounting shelves

Upgrading the VAX 4000 Model 100 System 2–13

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
Figure 2–10 Lifting the Drive Mounting Shelves Upward

MLO-010807

2–14 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
11. Disconnect the DSSI cable(s) from the DSSI daughter card (see
Figure 2–11).
12. Remove the DSSI daughter card by gently prying it loose from its connector
on the CPU module, and use a standoff removal tool to compress the posts
so that each corner of the card can be lifted off individually (Figure 2–11).
When all four corners are loose, lift the card out and place it on an
anti-static mat.
Figure 2–11 Removing the DSSI Daughter Card
1

4
3

MLO-012290

DSSI connector
Standoff removal tool
Standoff

Daughter card connector on the CPU module
DSSI daughter card

Upgrading the VAX 4000 Model 100 System 2–15

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
13. Remove all cables from the CPU module (Figure 2–12).
a. Disconnect the external SCSI cable, which runs from the port cover to
the CPU module, at the connector on the CPU module.
b. Disconnect the Q–bus cable.
c.

Disconnect any internal communications options cables that are
present in your system from the CPU module.

d. Disconnect the CPU power cable from the CPU module.
Figure 2–12 Disconnecting the Q–bus and external SCSI Cables
4

1
2

MLO-012291

External SCSI cable
Q–bus cable
Internal communications option cable(s)

CPU power cable

2–16 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
14. Remove the present port cover by pushing the tabs on each side (see
Figure 2–13). The tabs are accessed through the tab cutouts on the port
cover. Slide the cover off, pulling all cables carefully through the cable slots
on the rear of the system box.
Figure 2–13 Removing the Port Cover
2
1

3
MLO-010813

Port cover
Tab cutout

Cable slots on rear of the system box

Upgrading the VAX 4000 Model 100 System 2–17

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
15. Remove all connectors from the original port cover (see Figure 2–14). Save
the screws, nuts, and washers for use in connecting the new port cover.
Figure 2–14 Removing Connectors from the Port Cover

MLO-010814

Nut driver used for bolts on the Q–bus connectors
Phillips screwdriver used on the DSSI and SCSI connectors

2–18 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
16. Install two alignment pins with washers on the new port cover for the
original DSSI connector (see Figure 2–15).
Figure 2–15 Installing the Alignment Pins on the Port Cover
1

MLO-010815

Alignment pin
Washer

Upgrading the VAX 4000 Model 100 System 2–19

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
17. Install the single DSSI cable (17–03544–01) into the left DSSI port cutout
(see Figure 2–16).
Figure 2–16 Installing the Original DSSI Cable on the Port Cover

MLO-010816

Original DSSI cable connector
Pillips screwdriver

2–20 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
18. Install the Q–bus cable (17–03545–01) into the Q–bus cutouts on the port
cover (see Figure 2–17).
Figure 2–17 Installing the Q–bus Cable on the Port Cover

MLO-010817

Q–bus cable connectors
Nutdriver and bolt

Washer

Upgrading the VAX 4000 Model 100 System 2–21

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
19. Install the blank covers into the two right DSSI external cutouts on the
new port cover (see Figure 2–18).
Figure 2–18 Installing the Blank Covers on the Port Cover
2

MLO-012292

Blank covers
Phillips screwdriver and screw.

2–22 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
20. Install the SCSI cable (17–2944–01) into the SCSI cutout on the bottom of
the port cover (see Figure 2–19).
Figure 2–19 Installing the SCSI Cable on the Port Cover

3
2

MLO-012293

SCSI cable connector
Phillips screwdriver and screw

Washer

Upgrading the VAX 4000 Model 100 System 2–23

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
21. Install the new port cover with its connectors onto the rear of the system
box, feeding the cables through the cable cutouts in the system box (see
Figure 2–20).
a. Feed the single DSSI cable and the Q–bus cables through the top cable
cutout on the system box.
b. Feed the SCSI cable through the bottom cable cutout on the system
box.
c.

Hook the bottom flange of the cover plate onto the system box.

d. Push the port cover forward until the two tabs click into place.
Figure 2–20 Installing the Port Cover and Cables
1

4
3

2
MLO-012294

DSSI and Q–bus cables in top cutout
SCSI cable in bottom cutout
Bottom flange

Tab cutout

2–24 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
22. To remove the CPU module, follow these steps.
Caution
Ensure that you do not damage any of the CPU module components by
exerting too much force on them.

a. Press the two spring clips (marked by arrows in Figure 2–21) that
secure the CPU module in position. The CPU module moves forward
under the tension of the connector gaskets. If necessary, slide the CPU
module back until it disengages from the ten keyhole cutouts (refer to
Figure 2–21).
b. Use your finger, in the semicircular cutout on the front edge of the
CPU module, to lift up the front edge of the CPU module (refer to
Figure 2–21).
c.

While supporting the front of the CPU module with one hand, guide
the connectors on the back of the CPU module out of the corresponding
cutouts on the back of the enclosure.

d. Remove the CPU module from the enclosure.

Upgrading the VAX 4000 Model 100 System 2–25

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
Figure 2–21 Removing the CPU Module

PUSH

MLO-012295

Spring clips
Semicircular cutout

Keyhole cutouts (10)

2–26 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
23. To install the new CPU module, follow these steps:
a. Place the CPU module in the enclosure so that the connectors on the
CPU module align with the corresponding cutouts in the back panel of
the enclosure. Use the ThinWire Ethernet port as an anchor point to
adjust the position of the CPU module correctly.
b. Align the keyhole cutouts in the CPU module with the corresponding
standoff pillars in the base of the enclosure.
Caution
Ensure that you do not damage any of the CPU module components by
exerting pressure on them.

Press the CPU module at the two positions marked push. The spring
clips push the standoff pillars into the keyhole cutouts that secure the
CPU module in position. See Figure 2–21.

24. Install the DSSI daughter card onto the CPU module (see Figure 2–22).
Align the card on the standoffs so that it is positioned above the CPU
module connector, then gently seat it onto the connector and the standoffs.

Upgrading the VAX 4000 Model 100 System 2–27

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
Figure 2–22 Installing the DSSI Daughter Card
1

3
2

MLO-012296

Daughter card
Standoff

CPU module connector
Note
For clarity, cables not applicable to a particular step are omitted from
some of the following illustrations.

2–28 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
25. Connect the external SCSI cable (17–2944–01) to the CPU module (see
Figure 2–23).
Figure 2–23 Connecting the External SCSI Cable to the CPU Module
1
2

MLO-012297

External SCSI cable
External SCSI connector on the CPU module

Upgrading the VAX 4000 Model 100 System 2–29

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
26. Connect the DSSI cable (17–03544–01) to the connector slot on the DSSI
daughter card (see Figure 2–24).
Figure 2–24 Connecting the Single DSSI Cable to the Daughter Card
1

MLO-012298

Single DSSI cable
Rear connector slot on the daughter card

2–30 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
27. Connect the Q–bus cable (17–3545–01) to the Q–bus slot on the CPU
module (see Figure 2–25).
Figure 2–25 Connecting the Q–bus Cable to the CPU Module
1

MLO-012299

Q–bus cable
Q–bus connector on the CPU module

Upgrading the VAX 4000 Model 100 System 2–31

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
28. Reinstall the upper and lower drive mounting shelves in the system box,
and connect the internal SCSI cable (17–03587–01) to the CPU module.
a. Position the shelves by lining up the bracket tabs, but do not slide
them rearward yet (see Figure 2–26).
Figure 2–26 Aligning the Drive Mounting Shelves

1
MLO-012300

Bracket tabs

2–32 Upgrading the VAX 4000 Model 100 System

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
b. Connect the internal SCSI cable to its connector on the CPU module.
(see Figure 2–27).
c.

Slide the shelves down and rearward into place so that the holes on the
bracket tabs line up with their cutouts.

Figure 2–27 Reinstalling the Drive Mounting Shelves

MLO-012301

Internal SCSI cable

Upgrading the VAX 4000 Model 100 System 2–33

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
d. Tighten the shelves in place using the six screws that held them in
originally (see Figure 2–28).
1. Tighten the topmost captive screw first so that the shelves do not
fall and damage components underneath.
2. Tighten the remaining captive screws.
3. Replace and tighten the Phillips screws.
Figure 2–28 Securing the Drive Mounting Shelves

3
2

MLO-012302

Topmost captive screw
Other captive screws

2–34 Upgrading the VAX 4000 Model 100 System

Phillips screws

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module

29. Reinstall the SIMMs as follows, beginning with the module closest to the
front of the enclosure (Figure 2–29).
Caution
When installing a SIMM, note that the connectors on the CPU module
are keyed so that you cannot install the module with an incorrect
orientation. Do not try to force a module into a connector with an
incorrect orientation.

Note
The SIMMs must be reinstalled into the same slots they came from.

1. Tip the memory module rearward.
2. Slide the module into its connector while still tipped rearward, and tip
it back upright.

Upgrading the VAX 4000 Model 100 System 2–35

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
Figure 2–29 Installing a SIMM

MLO-012303

Sliding the module in

2–36 Upgrading the VAX 4000 Model 100 System

Tipping it upright

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module

30. Reconnect the DSSI connectors to the drives (see Figure 2–6).
31. Reconnect the internal power cables (see Figure 2–5).
32. Reinstall the enclosure cover (see Figure 2–3).
33. Reconnect cables and terminators to the DSSI, Q–bus, and SCSI connectors
on the port cover as desired (see Figure 2–30).
Figure 2–30 Reconnecting Cables and Terminators
1

3
2

2
3
MLO-012310

DSSI connector/terminator
Q–bus connectors

SCSI connector/terminator

Upgrading the VAX 4000 Model 100 System 2–37

Upgrading the VAX 4000 Model 100 System
2.5 Replacing the CPU Module
34. Replace the Ethernet connector, if any (see Figure 2–2).
35. Place the new label, 36–30382–23 (24), whichever is appropriate for your
country, over the existing label.
36. Remove the system medallion and install the new one, 74–37642–32. See
Figure 2–31.
a. Peel the backing off the new medallion.
b. Apply the new medallion in place of the original one.
Figure 2–31 Applying the New Medallion
1

MLO-010951

Backing
New medallion

Medallion location

37. Apply the conversion label (36–15946–00) in any spot on the system box
you wish.
38. Have the customer reinstall system data (if necessary).
39. Fill out the forms in Appendix A.
40. Return the original CPU module as instructed (see Appendix A).

2–38 Upgrading the VAX 4000 Model 100 System

3
Upgrading the VAX 4000 Model 100A
System
3.1 In This Chapter
This chapter lists detailed step-by-step procedures for upgrading a VAX Model
100A system to a VAX Model 105A system.

3.2 Procedure Overview
The conversion procedure is summarized next. To begin the actual conversion,
turn to Section 3.3.
1. Have the customer back up the system software.
2. Unpack and verify the conversion kit.
3. Shut down the operating system and run the power up diagnostics.
4. Turn off the system power and remove the power cord.
5. Remove the enclosure cover.
6. Remove the SIMMs (memory modules).
7. Remove the upper and lower drive mounting shelves.
8. Disconnect and remove the DSSI daughter card.
9. Disconnect all internal cables from the port cover to the CPU module,
daughter cards and the drives.
10. Remove the CPU module.
11. Install the new CPU module.
12. Reinstall the SIMMs.
13. Reconnect all cables and daughter cards to the CPU module.
14. Reinstall the upper and lower drive mounting shelves in the system box,
and reconnect all cables.
Upgrading the VAX 4000 Model 100A System 3–1

Upgrading the VAX 4000 Model 100A System
3.2 Procedure Overview
15. Reinstall the enclosure cover.
16. Connect the power cable, signal cables, and terminators to the system as
desired.
17. Turn on the system.
18. Have the customer reinstall system data (if necessary).
19. Fill out the forms in Appendix A.
20. Return the CPU module as instructed (see Appendix A).
Note
Firmware and VMS upgrades are not required; appropriate versions
were installed on VAX 4000 Model 100A systems at the factory.

3.3 Unpacking the Kit
Unpack the kit as follows:
1. Make sure there is no external damage to the shipping container, such as
dents, holes, or crushed corners.
2. Unpack the conversion kit and check its contents against the shipping
invoice. Table 3–1 lists the kit contents for the Model 100/100A upgrade to
Model 105A, 53XR–AA. Other items may be present, but are not required
for this conversion.
CAUTION
Static discharge can damage modules. Use an antistatic wrist strap
and antistatic mat during handling. The wrist strap and mat are in
the antistatic kit in the Digital Services toolkit.

3. Unpack the CPU module and place it on a grounded antistatic mat.
4. Save the packing material, and use it to return the original CPU module.

3–2 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.3 Unpacking the Kit
5. If any item is missing or damaged:
•

Contact the customer’s sales representative.

•

Contact the customer’s delivery agent.

Table 3–1 Contents of the 53XR–AA Upgrade Kit
Description

Part Number

Quantity

Wire harness assy

17–03615–001

Product conversion label

36–15946–00

Regulatory label

36–30382–23(24)

NVAX CPU

54–21797–02

Medallion

74–37642–32

DSSI blank panel

74–46956–01

Expansion port cover

74–46957–01

Machine screw, 8mm

90–10917–01

VAX 4000 100/100A Upgrade to
Model 105A

EK–V411A–CG

VMS multimedia Viking

QA–001AA–UW

Model 105A doc set

QZ–K04AB–GZ

3.4 Before Installing the Kit
Before installing the kit:
1. Have the customer back up the system software before the Digital Services
representative arrives. It is the customer’s responsibility to back up the
system software.
2. Shut down the operating system in the proper manner.
3. Power up the system and run diagnostics to verify system operation.
4. Turn off the system power before installing the kit.

Upgrading the VAX 4000 Model 100A System 3–3

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module

3.5 Installing the CPU Module
To install the new CPU module (convert to a VAX 4000 Model 105A):
1. Disconnect the power cord from the wall outlet, then from the system (see
Figure 3–1).
Figure 3–1 Disconnecting the Power Cord

3
2

MLO-010952

Power cord

3–4 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
2. Remove the enclosure cover by removing the two screws at the rear of the
system box and sliding it forward (see Figure 3–2).
Figure 3–2 Removing the Enclosure Cover

3
2

1
MLO-010953

Screws
Enclosure cover

Upgrading the VAX 4000 Model 100A System 3–5

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
3. Remove the upper and lower drive mounting shelves together as a single
unit (it is not necessary to disassemble the shelves themselves). Unscrew
all six screws from the shelves, leaving the topmost captive screw until
last for support. Leave the capitve screws in position and save the Phillips
screws for reinstallation of the shelves (see Figure 3–3).
Figure 3–3 Unscrewing the Drive Shelves

3
2

MLO-012302

Topmost captive screw
Other captive screws

Phillips screws

3–6 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
4. Disconnect the internal power cables from the power supply (Figure 3–4).
5. Disconnect the pigtailed, 2-pin DSSI power cable from the CPU module.
(Figure 3–4).

Upgrading the VAX 4000 Model 100A System 3–7

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
Figure 3–4 Disconnecting the Internal Power Cables

MLO-012306

Internal power cable
Internal power cable with pigtailed DSSI power cable

CPU module DSSI power cable connector

3–8 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
6. Disconnect the internal DSSI connectors from all drives mounted on the
shelves. Figure 3–5 shows one drive as an example.
Figure 3–5 Disconnecting Internal DSSI Connectors

MLO-010804

Internal DSSI connectors
7. Remove all SIMMs from the CPU module. (See Figure 3–6).
Caution
Static electricity can damage integrated circuits. Wear a wrist strap
and place an antistatic mat under the system unit when working with
the internal parts of the system unit.

Note
Note carefully the position of each memory module you remove; they
must be reinstalled later into the same slots.
Beginning with the SIMMs closest to the front of the enclosure remove
each as follows:
1. Release the memory module by pressing the metal board clips on the
memory module connector away from the center.
2. Tip the memory module rearward.

Upgrading the VAX 4000 Model 100A System 3–9

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
3. Lift the memory module up and out of the enclosure, and place it on an
anti-static mat.
Figure 3–6 Removing a SIMM

Metal Board Clip

MS44 Memory Modules

MLO-012304

3–10 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
8. Disconnect the internal SCSI cable from the CPU module (see Figure 3–7).
Figure 3–7 Disconnecting the Internal SCSI Cable from the CPU Module
1

MLO-012305

Internal SCSI cable

Upgrading the VAX 4000 Model 100A System 3–11

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
9. Remove the shelves by sliding them forward (see Figure 3–8) and lifting
them forward and up from the enclosure (see Figure 3–9).
Figure 3–8 Sliding the Drive Mounting Shelves Forward
1

MLO-012307

Drive mounting shelves

3–12 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
Figure 3–9 Lifting the Drive Mounting Shelves Upward

MLO-012289

Upgrading the VAX 4000 Model 100A System 3–13

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
10. Disconnect the DSSI cable from the DSSI daughter card (see Figure 3–10).
11. Remove the DSSI daughter card by gently prying it loose from its connector
on the CPU module, and use a standoff removal tool to compress the posts
so that each corner of the card can be lifted off individually (Figure 3–10).
When all four corners are loose, lift the card out and place it on an
anti-static mat.
Figure 3–10 Removing the DSSI Daughter Card

4
3

MLO-012311

DSSI connector
Standoff removal tool
Standoff

Daughter card connector on the CPU module
Single DSSI daughter card

3–14 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
12. Remove all cables from the CPU module (Figure 3–11).
a. Disconnect the external SCSI cable, which runs from the port cover to
the CPU module, at the connector on the CPU module.
b. Disconnect the Q–bus cable.
c.

Disconnect any internal communications options cables that are
present in your system from the CPU module.

d. Disconnect the CPU power cable from the CPU module.
Figure 3–11 Disconnecting the Q–bus and external SCSI Cables
4

1
2

MLO-012308

External SCSI cable
Q–bus cable
Internal communications option cable(s)

CPU power cable

Upgrading the VAX 4000 Model 100A System 3–15

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
13. To remove the CPU module, follow these steps.
Caution
Ensure that you do not damage any of the CPU module components by
exerting too much force on them.

a. Press the two spring clips (marked by arrows in Figure 3–12) that
secure the CPU module in position. The CPU module moves forward
under the tension of the connector gaskets. If necessary, slide the CPU
module back until it disengages from the ten keyhole cutouts (refer to
Figure 3–12).
b. Use your finger, in the semicircular cutout on the front edge of the
CPU module, to lift up the front edge of the CPU module (refer to
Figure 3–12).
c.

While supporting the front of the CPU module with one hand, guide
the connectors on the back of the CPU module out of the corresponding
cutouts on the back of the enclosure.

d. Remove the CPU module from the enclosure.

3–16 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
Figure 3–12 Removing the CPU Module

PUSH

MLO-012295

Spring clips
Semicircular cutout

Keyhole cutouts (10)
Upgrading the VAX 4000 Model 100A System 3–17

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
14. To install the new CPU module, follow these steps:
a. Place the CPU module in the enclosure so that the connectors on the
CPU module align with the corresponding cutouts in the back panel of
the enclosure. Use the ThinWire Ethernet port as an anchor point to
adjust the position of the CPU module correctly.
b. Align the keyhole cutouts in the CPU module with the corresponding
standoff pillars in the base of the enclosure.
Caution
Ensure that you do not damage any of the CPU module components by
exerting pressure on them.

Press the CPU module at the two positions marked push. The spring
clips push the standoff pillars into the keyhole cutouts that secure the
CPU module in position. See Figure 3–12.

15. Install the DSSI daughter card onto the CPU module (see Figure 3–13).
Align the card on the standoffs so that it is positioned above the CPU
module connector, then gently seat it onto the connector and the standoffs.

3–18 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
Figure 3–13 Installing the DSSI Daughter Card
1

3
2

MLO-012296

Daughter card
Standoff

CPU module connector
Note
For clarity, cables not applicable to a particular step are omitted from
some of the following illustrations.

Upgrading the VAX 4000 Model 100A System 3–19

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
16. Connect the external SCSI cable (17–2944–01) to the CPU module (see
Figure 3–14).
Figure 3–14 Connecting the External SCSI Cable to the CPU Module
1
2

MLO-012297

External SCSI cable
External SCSI connector on the CPU module

3–20 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
17. Connect the DSSI cable (17–03544–01) to the connector slot on the DSSI
daughter card (see Figure 3–15).
Figure 3–15 Connecting the Single DSSI Cable to the Daughter Card
1

MLO-012298

Single DSSI cable
Rear connector slot on the daughter card
Note
If your system has the dual DSSI option, run the dual DSSI in/out
cable (17–03778–01) between the rows of memory module slots and
connect it to the front connector slot on the DSSI daughter card (closest
to the front of the enclosure).

Upgrading the VAX 4000 Model 100A System 3–21

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
18. Connect the Q–bus cable (17–3545–01) to the Q–bus slot on the CPU
module (see Figure 3–16).
Figure 3–16 Connecting the Q–bus Cable to the CPU Module
1

MLO-012299

Q–bus cable
Q–bus connector on the CPU module

3–22 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
19. Reinstall the upper and lower drive mounting shelves in the system box,
and connect the internal SCSI cable (17–03587–01) to the CPU module.
a. Position the shelves by lining up the bracket tabs, but do not slide
them rearward yet (see Figure 3–17).
Figure 3–17 Aligning the Drive Mounting Shelves

1
MLO-012300

Bracket tabs

Upgrading the VAX 4000 Model 100A System 3–23

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
b. Connect the internal SCSI cable to its connector on the CPU module
(see Figure 3–18).
c.

Slide the shelves down and rearward into place so that the holes on the
bracket tabs line up with their cutouts.

Figure 3–18 Reinstalling the Drive Mounting Shelves

MLO-012305

Internal SCSI cable

3–24 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
d. Tighten the shelves in place using the six screws that held them in
originally (see Figure 3–19).
1. Tighten the topmost captive screw first so that the shelves do not
fall and damage components underneath.
2. Tighten the remaining captive screws.
3. Replace and tighten the Phillips screws.
Figure 3–19 Securing the Drive Mounting Shelves

3
2

MLO-012302

Topmost captive screw

Phillips screws

Other captive screws

Upgrading the VAX 4000 Model 100A System 3–25

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module

20. Reinstall the SIMMs as follows, beginning with the module closest to the
front of the enclosure (Figure 3–20).
Caution
When installing a SIMM, note that the connectors on the CPU module
are keyed so that you cannot install the module with an incorrect
orientation. Do not try to force a module into a connector with an
incorrect orientation.

Note
The SIMMs must be reinstalled into the same slots they came from.

1. Tip the memory module rearward.
2. Slide the module into its connector while still tipped rearward, and tip
it back upright.

3–26 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
Figure 3–20 Installing a Memory Module

MLO-012303

Sliding the module in

Tipping it upright

Upgrading the VAX 4000 Model 100A System 3–27

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module

21. Reconnect the DSSI connectors to the drives (see Figure 3–5).
22. Reconnect the internal power cables (see Figure 3–4).
23. Reinstall the enclosure cover (see Figure 3–2).
24. Place the new label, 36–30382–23 (24), whichever is appropriate for your
country, over the existing label.
25. Remove the system medallion and install the new one, 74–37642–32. See
Figure 3–21.
a. Peel the backing off the new medallion.
b. Apply the new medallion in place of the original one.
Figure 3–21 Applying the New Medallion
1

MLO-010951

Backing
New medallion

Medallion location

3–28 Upgrading the VAX 4000 Model 100A System

Upgrading the VAX 4000 Model 100A System
3.5 Installing the CPU Module
26. Apply the conversion label (36–15946–00) in any spot on the system box
you wish.
27. Have the customer reinstall system data (if necessary).
28. Fill out the forms in Appendix A.
29. Return the original CPU module as instructed (see Appendix A).

Upgrading the VAX 4000 Model 100A System 3–29

A
Mandatory Return Procedure and Forms
The original CPU module must be returned to Digital Equipment Corporation.
Digital Services personnel must follow the instructions for repackaging and
returning the original CPU. The instructions apply only to United States area
installations.
For installations outside the United States area, contact the local Digital
Equipment Corporation office for return destination instructions.

A.1 Return Procedure
Note
Customers who do not return their original CPU modules will be
charged a fee.

Return the original CPU module as follows:
1. Obtain the serial number of the system being converted. Customer
Administrative Services (CAS) cannot process the order without this serial
number.
2. Ensure that the serial number is on the purchase order.
3. Issue a hardcopy quotation to the customer, referencing the serial number,
and state the following:
"Return of the replaced modules to Digital is a condition of sale for
this conversion. Failure to return the modules will result in a penalty
charge. Installation of hardware by Digital Services personnel is
required."
4. Pack the original CPU module using the packaging material set aside from
the carton of the conversion kit.

Mandatory Return Procedure and Forms A–1

Mandatory Return Procedure and Forms
A.1 Return Procedure
Pack the module first in the nickel-plated bag, then in the pink plastic
wrapping, and finally in the box. Do not seal the box for shipping until you
have included all necessary paperwork.
5. Complete the Digital Services Worksheet in Section A.2. It documents the
work you performed.
Return the worksheet to your contract administrator at the branch office.
6. Contact your local Digital CAS office to obtain information for the
Installation Receipt and the Return Material Checklist in Section A.2.
Ask the CAS representative for a return authorization (RA) number. CAS
will contact the customer to arrange for carrier pickup and return of the
module to Digital Equipment Corporation.
7. Complete both copies of the Installation Receipt.
The first copy is the customer’s receipt. It shows that the installation was
completed and that Digital Services contacted CAS.
Return the second copy to Digital Services along with the original CPU
module card so that the customer does not incur a penalty charge.
8. Complete the Returned Material Checklist.
Return the checklist with the original module.
9. Place the self-adhesive mailing label on the box to be returned.
Write the return authorization (RA) number in the space provided on the
label.
10. Seal the box for shipment.
Refer questions regarding the return procedure to the local account
representative.

A.2 Return Forms
This section contains the:
•

Digital Services Worksheet

•

Installation Receipt–Customer Copy

•

Installation Receipt–Digital Services Copy

•

Returned Material Checklist

A–2 Mandatory Return Procedure and Forms

Mandatory Return Procedure and Forms
A.2 Return Forms

Digital Services Worksheet
This form acts as a verification of the work performed on the system and as a
check on the procedures used. Please fill out this form and return it to your
Contract Administrator for updating the customer’s contract.
Customer:
Previous System Model Number:
Previous System Serial Number:
Original CPU Module Serial Number:

New System Name:
New System Model Number:
New System Serial Number:
New CPU Module Serial Number:
Comments:

Mandatory Return Procedure and Forms A–3

Mandatory Return Procedure and Forms
A.2 Return Forms

A–4 Mandatory Return Procedure and Forms

Mandatory Return Procedure and Forms
A.2 Return Forms

Installation Receipt—Customer Copy
For the upgrade of VAX 4000 Model 100 or VAX 4000 Model 100A to VAX 4000
Model 105A.
This form acts as a customer receipt and as verification for Digital Services
that the CPU module upgrade kit was installed.
Digital Services:

Complete both copies of this form. Give a copy to the customer and
a copy to the local CAS office for filing with customer documents.

Customer:

Digital Equipment Corporation will contact you within the next
several days to arrange for package pickup and return. Keep
this copy as your record of installation by Digital Equipment
Corporation.

Note
Contact the local CAS office to obtain the RA (return authorization)
number. You should have the Digital order number available. Be sure
to note the name of the person you speak with.

Name of CAS representative:
Branch Office:

, will arrange for package pickup and return.

Return Authorization (RA) Number:
Digital Order Number:
Original CPU Module Serial Number:
Converted to:
New System Serial Number:
New CPU Module Serial Number:
Installation was performed on this date:
(See overleaf for signatures)

Mandatory Return Procedure and Forms A–5

Mandatory Return Procedure and Forms
A.2 Return Forms
CPU Module Packed for Return:
Customer Name:

Phone Number:

Customer Signature:
Digital Services Representative Signature:

A–6 Mandatory Return Procedure and Forms

Mandatory Return Procedure and Forms
A.2 Return Forms

Installation Receipt—Digital Services Copy
For the upgrade of VAX 4000 Model 100 or VAX 4000 Model 100A to a
VAX 4000 Model 105A.
This form acts as a verification for Digital Services that the CPU module
upgrade kit was installed.
Digital Services:

Complete both copies of this form. Give a copy to the customer and
a copy to the local CAS office for filing with customer documents.

Note
Contact the local CAS office to obtain the RA (return authorization)
number. You should have the Digital order number available. Be sure
to note the name of the person you speak with.

Name of CAS representative:
Branch Office:

, will arrange for package pickup and return.

(See overleaf for signatures)

Mandatory Return Procedure and Forms A–7

Mandatory Return Procedure and Forms
A.2 Return Forms
CPU Module Packed for Return:
Customer Name:

Phone Number:

Customer Signature:
Digital Services Representative Signature:

A–8 Mandatory Return Procedure and Forms

Mandatory Return Procedure and Forms
A.2 Return Forms

Returned Material Checklist
For the upgrade of VAX 4000 Model 100 or VAX 4000 Model 100A to a
VAX 4000 Model 105A.
This form must be filled out and returned with the original daughter card to
ensure that the customer does not incur a penalty charge.

Return Authorization (RA) Number:
Digital Order Number:
Customer Name:
Customer Address:

Customer Contact:

********* Include This Form With Your Module Return*********

Mandatory Return Procedure and Forms A–9

How to Order Additional Documentation

Technical Support
If you need help deciding which documentation best meets your needs, call 800-DIGITAL
(800-344-4825) and press 2 for technical assistance.

Electronic Orders
If you wish to place an order through your account at the Electronic Store, dial
800-234-1998, using a modem set to 2400- or 9600-baud. You must be using a VT
terminal or terminal emulator set at 8 bits, no parity. If you need assistance using
the Electronic Store, call 800-DIGITAL (800-344-4825) and ask for an Electronic Store
specialist.

Telephone and Direct Mail Orders
From

Call

Write

U.S.A.

DECdirect
Phone: 800-DIGITAL
(800-344-4825)
Fax: (603) 884-5597

Digital Equipment Corporation
P.O. Box CS2008
Nashua, NH 03061

Puerto Rico

Phone: (809) 781-0505
Fax: (809) 749-8377

Digital Equipment Caribbean, Inc.
3 Digital Plaza, 1st Street
Suite 200
Metro Office Park
San Juan, Puerto Rico 00920

Canada

Phone: 800-267-6215
Fax: (613) 592-1946

Digital Equipment of Canada Ltd.
100 Herzberg Road
Kanata, Ontario, Canada K2K 2A6
Attn: DECdirect Sales

International

—————

Local Digital subsidiary or
approved distributor

Internal Orders1
(for software
documentation)

DTN: 264-3030
(603) 884-3030
Fax: (603) 884-3960

U.S. Software Supply Business
Digital Equipment Corporation
10 Cotton Road
Nashua, NH 03063-1260

Internal Orders
(for hardware
documentation)

DTN: 264-3030
(603) 884-3030
Fax: (603) 884-3960

U.S. Software Supply Business
Digital Equipment Corporation
10 Cotton Road
Nashua, NH 03063-1260

1 Call to request an Internal Software Order Form (EN–01740–07).

Reader’s Comments

VAX 4000
Model 100/100A Upgrade
to Model 105A
EK–V411A–CG. A01

Your comments and suggestions help us improve the quality of our publications.
Thank you for your assistance.

I rate this manual’s:

Excellent

Good

Fair

Accuracy (product works as manual says)
Completeness (enough information)
Clarity (easy to understand)
Organization (structure of subject matter)
Figures (useful)
Examples (useful)
Index (ability to find topic)
Page layout (easy to find information)
I would like to see more/less
What I like best about this manual is
What I like least about this manual is

I found the following errors in this manual:
Page
Description

Additional comments or suggestions to improve this manual:

For software manuals, please indicate which version of the software you are using:

Name/Title

Dept.

Company

Date

Mailing Address
Phone

Poor

Do Not Tear – Fold Here and Tape
TM

BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 33 MAYNARD MASS.
POSTAGE WILL BE PAID BY ADDRESSEE

DIGITAL EQUIPMENT CORPORATION
Information Design and Consulting
MRO1–3/K10 BS
200 FOREST STREET
MARLBORO, MA 01752-3011

Do Not Tear – Fold Here

No Postage
Necessary
If Mailed
in the
United States