Digital PDFs

EK-V400H-IN-002

June 1991

9 pages

Original

47.1kB

Document:	VAX 4000 Model 200 (BA430) Installation Checklist
Order Number:	EK-V400H-IN
Revision:	002
Pages:	9
Original Filename:

OCR Text

VAX 4000 Model 200 (BA430)
Installation Checklist
EK–V400H–IN–002
June 1991

Digital Equipment Corporation
Maynard, Massachusetts

Getting Started
This checklist assumes that your entire
system arrived and that you are ready
to unpack and place it in its appropriate
location.
Before proceeding, unpack all cartons and
check the contents of each carton against the
Product Delivery Document (shipping list).
If any item is missing or damaged, contact
your delivery agent and your Digital sales
representative.
Caution: Before you install your system,
review the system warranty. The terms of
your agreement with Digital may require
that a Digital service representative install
your system. Contact your local Digital
representative if you have any questions.
How to Use This Checklist
Use this checklist in conjunction with, not
as a replacement for, your Installation
manual. The numbered steps in this checklist
correspond to the numbered steps in that
manual.
Note: If you are installing a dual-host
system, you must repeat each step for each
host.
Each step in this checklist makes reference
(in parentheses) to the manual that contains
more information about the step. As you
complete each step in the Installation
manual:
1. Refer back to this checklist.
2. Verify that you performed the required
task.
3. Check the appropriate box.

Documents You Will Need
Find your Customer Hardware Information
Kit. It consists of several manuals and a gray
vinyl binder to hold them.
To install and use your system, you need the
following documents.
•

•
•
•

These manuals from the Customer
Hardware Information Kit:
Site Preparation
Installation
Operation
Troubleshooting and Diagnostics
VAX 4000 Dual Host Systems, if
installing a dual-host system
Console terminal documents found with
the console terminal
Operating system documents
Documents for any devices such as
expanders or printers

Questions, problems or concerns? Call
Digital’s toll-free hotline 24 hours a day:
In the U.S., 1–800–DEC–8000
In Canada, 1–800–267–5251

1 Verify Site Preparation
Is there adequate power for your system
and its peripherals? (Site Preparation)
Are you allowing enough space for your
system? (Site Preparation)
Does your site maintain the proper
environmental operating conditions?
(Site Preparation)
Did you gather the tools you will need?
(Installation)
Are you installing a dual-host system?
If so, repeat each step for each system.
(Installation)

2 Check the Shipment
Did you check the Product Delivery
Document against the Content Listings
for each carton? (Installation)
Did you compare the contents of your
cartons with the Content Listings for each
carton? (Installation)

3 Position the System
Does the location for your system
meet the system’s weight and space
requirements? (Installation, Site
Preparation)

4 Open the System Doors
Did you find the key to the lock in the
shipping carton? (Installation)
Did you turn that key to the bottom
position to unlock the upper and lower
doors? (Installation)

5 Install the Console Terminal
Did you unpack the console terminal
components? (Terminal installation
guide)
Did you connect all console terminal
components? (Terminal installation
guide)
Did you turn on the console terminal
and observe proper self-tests? (Terminal
owner’s manual)
Did you perform setup operations for
the console terminal? (Terminal owner’s
manual)
Did you turn off the console terminal?
(Installation)
Did you connect the DECconnect cable
from the rear of the console terminal
to the system CPU cover panel?
(Installation)

6 Set the System Controls
Did you set the Power switch to off (0)?
(Installation)
Did you set the Halt button to the out
(run) position? (Installation)

On each ISE did you set the Write-Protect
button to the out (write-enabled) position
and the Run/Ready button to the in
(ready) position? (Installation)
Did you verify that a bus node ID plug
is inserted into each ISE and TF85
tape drive installed in your system?
(Installation)
Did you set the Power-Up Mode switch to
Language Inquiry mode (indicated by a
human profile)? (Installation)
Did you set the Break Enable/Disable
switch to break enabled (up position)?
(Installation)
Does your system have a TK-series or
TF85 tape drive? If so, did you make sure
the Cartridge Insert/Release handle is
closed (pushed in)? (Installation)

7 Connect Additional Devices to the
System
Did you connect terminals and printers to
the system? (Installation)
Did you connect telephones to the
modems on the system? (Installation)
Did you connect the system to a network?
(Installation)

8 Connect an Expander, If Required
Are you installing an expander with
your system? If so, begin installing the
expander now. When the installation
is complete, return to this checklist.
(Expander addendum or manual, system
Installation)

9 Connect the KZQSA Internal
Cable, If Required
Did you connect one end of the cable to
the KZQSA In connector on your system?
(Installation)
Did you connect the other end of the cable
to the upper connector on the KZQSA
module? (Installation)

10 Connect the DSSI Cable — Dual
Host Only
Did you connect one end of the cable to
the DSSI In/Out connector on host A?
(Installation)
Did you connect the other end of the cable
to the DSSI In/Out connector on host B?
(Installation)

11 Connect the Ground Cable —
Dual Host Only
Did you connect the cable to the Ground
Wire Out bolt on host A? (Installation)
Did you connect the other end of the cable
to the Ground Wire Out bolt on host B?
(Installation)

12 Connect the System Power Cable
Did you turn off the system and all its
devices? (Installation)
Did you connect the power cable to the
system and to a wall outlet or other power
source? (Installation)

13 Turn On the System and Select a
Language
Did you turn on the console terminal and
observe proper self-tests? (Installation)
Did you turn on the system by setting the
Power switch to on (1)? (Installation)
Did you select a language and save it
by turning the Power-Up Mode switch
to Run mode (indicated by an arrow)?
(Installation)

14 Close the System Doors
Did you close the front doors? (Installation)
Did you turn the key to the middle
position to lock both doors or to the top
position to leave the upper door unlocked?
(Installation)

15 After Installation
Did you learn how to operate the system
controls and mass storage devices?
(Operation)
Did you run the MicroVAX Diagnostic
Monitor (MDM) software, if ordered?
(Troubleshooting and Diagnostics)
Did you start up and modify factoryinstalled software, if present? (Installation)
Did you install the operating system
software? (Software installation manual)

S1663