Digital PDFs

EK-MX34S-IN-A01

2000

12 pages

Original

0.2MB

Document:	MicroVAX 3100 Model 30 to DEC 3000 Model 400S AXP Upgrade Instructions
Order Number:	EK-MX34S-IN
Revision:	A01
Pages:	12
Original Filename:

OCR Text

MicroVAX 3100 Model
30 to DEC 3000 Model
400S AXP
Upgrade Instructions

MLO-010669

Part Number: EK–MX34S–IN. A01

Options You Can Upgrade

Drives:

Expansion
Boxes:

Memory:
Communication
Options:

Can
Upgrade

Cannot
Upgrade

RZ23L, 24L
RZ24, 25, 26
RZ55*
RZ56*
RZ58*
RX26
TZK10
RRD42**
TLZ04*
TLZ06**
TZ85*
TZ86***
TZ30****

RZ22
RZ23
RZ27
RZ35
RZ57
RZ59
RX23
RX33
TK50Z
DSSI Devices

SZ03
SZ12
SZ16
None

DHW42
DSW41

*External device support only.
**External device (including tabletop) support only.
***Support planned for external device.
****Latest version of TZ30 only.

Check Components Shipped
Your shipment should contain the following
two kits.
If you are missing any of these components,
contact your Digital sales representative.
System Kit:

Ethernet Loopback
Connector

System Unit
Documentation

SCSI
Terminator

Modem Loopback
Connector
Printer Port
Terminator

Antistatic
Wrist Strap

System Power
Cord

Network
Label

Screwdriver

Accessory Kit:
Upgrade
Card

xx
xx xxxx
xx
xx x
x
xx
xx

Rubber
Grommets

RX26 Brackets

Metal Support
Plate
TZ30 RFI
Shield

Return
Address Label
MLO-010670

Remove the System Unit Cover
Follow these steps to remove the system unit
cover:
1. Turn off the system by pressing the
on/off switch to the off (O) position.
2. Disconnect the cables, connectors, and
terminators from the system unit.
3. Loosen the two captive screws on the
back of the system unit.

Captive
Screws

MLO-010741

4. Slide the cover forward and lift it up
from the system unit. Set the cover
aside.

Remove Fixed Disk Drives
Note: The DEC 3000 system can hold two
fixed disk drives and one removable-media
drive.
1. Press and hold the spring clip that locks
the disk drive in position.
2. Push the disk drive towards the spring
clip until the rubber grommets under the
disk drive release from the cutouts in the
drive mounting shelf.

Spring Clip

MLO-010742

3. Lift the disk drive up from the drive
mounting shelf and release the spring
clip.
4. Disconnect the SCSI and power cables
from the back of the drive.
5. Set the drive aside on an antistatic mat.

Remove Diskette/CD/Tape Drive
Follow these steps to remove a removablemedia drive from the lower drive shelf:
1. Loosen the captive screw that secures the
drive mounting bracket to the drive shelf.

Captive Screw

MLO-010743

2. Lift the left side of the drive until the tabs
on the right side clear the cutouts in the
drive shelf.
3. Disconnect the SCSI and power cables
from the back of the drive.
4. Set the drive aside on an antistatic mat.

Check the SCSI ID Settings
Each device in your system must have its
own unique SCSI ID setting. If your DEC
3000 system has a factory-installed drive, it
is set to SCSI ID 3.
You can check the SCSI ID settings on your
drives by referring to the DEC 3000 Model
400/400S AXP Options Guide. The RZ23L
and RZ24 SCSI ID settings (not covered in
the guide) are shown here.
RZ23L Drive SCSI ID Settings:

E3 E2

SCSI
Settings: 0
4
1
5
2
6
3
MLO-010587

Check the SCSI ID Settings
RZ24 Drive SCSI ID Settings:

E3 2
E 1
E

E1 E2

SCSI
Settings: 0
4
1
5
2
6
3
MLO-010586

Install New Mounting Brackets
Remove the mounting brackets from all the
drives you are upgrading, unless you are
upgrading an RZ23L or RZ24 drive that has
the support plate shown below.
To attach the support plate (from the accessory kit) to your drives:
1. Place the metal support plate on the disk
drive as shown.
2. Screw the four rubber grommets into
the plate and the drive until the plate is
secure.

Rubber
Grommets

Metal Support
Plate
MLO-010588

Other Accessory Brackets
Install the RX26 bracket extensions as
shown below:

MLO-010719

The DEC 3000 Model 400/400S AXP
Options Guide explains how to attach the
RFI shield to the TZ30 drive, and how to
mount a removable-media drive in the
system mounting bracket.

Install the DEC 3000 System
1. Follow the instructions in the DEC 3000
Model 400/400S AXP Owner’s Guide to
set up and install that system.
2. Follow the instructions in the DEC 3000
Model 400/400S AXP Options Guide to
install the options in your new system.
3. Connect the terminal, keyboard, and
power cables, as shown.

ISDN
S3

MLO-010671

4. Turn on the DEC 3000 AXP system.

Complete the Upgrade
1. Test the installation by turning on your
new system and entering the show
device command at the console
prompt.
The drives you upgraded should appear
in the display. If a drive does not
display, it has not been installed properly.
2. Return your MicroVAX system to Digital
as follows:
a. Pack the MicroVAX system unit
securely in packing material for
shipment.
b. Attach the return-address label that
came in the upgrade accessory kit.
3. Contact your Digital service representative to upgrade your hardware service
contract.