Digital PDFs

EK-DS10V-UR-B01

2000

10 pages

Original

94.0kB

Document:	AlphaServer for OpenVMS VS10 User Reference Card
Order Number:	EK-DS10V-UR
Revision:	B01
Pages:	10
Original Filename:

OCR Text

EK–DS10V–UR. B01

ALPHASTATION XP900
USER REFERENCE CARD
This document is intended as a quick reference for the user.
Additional information can be found in the AlphaStation
XP900 Console Reference guide, EK-DS10V-CR.
Overview
• Environmental Specifications
•

Mechanical Specifications

•

Electrical Specifications

•

Front Buttons and LEDs

•

Ethernet LEDs

•

Beep Codes

•

PCI Slots

•

Memory Configuration

•

SRM Console Commands

•

Remote Management Console (RMC) Commands

•

Acoustics
WARNING: To prevent injury, access is limited to
persons who have appropriate technical training and
experience. Such persons are expected to understand
the hazards of working within this equipment and take
measures to minimize danger to themselves or others.
CPU modules and memory modules have parts that
operate at high temperatures. Wait 2 minutes after
power is removed before touching any module. Wear
an antistatic wrist strap when working on this system.

To reduce the risk of electrical shock or damage to the
equipment: Do not disable the power cord grounding
plug. The grounding plug is an important safety
feature. Plug the power cord into a grounded
(earthed) electrical outlet that is easily accessible at
all times. Disconnect power by unplugging the power
cord from the electrical outlet or the workstation.

Environmental Specifications
Storage
temperature range

–40º C to 66º C
(–40º F to 151º F)

Operating
temperature range

10º C to 40º C
(50º F to 104º F)

Max. rate of change

11º C (20º F) per hour

Storage
humidity range
(noncondensing)

10% to 90% relative humidity;
maximum wet bulb 65º C (149º F)

Operating
humidity range
(noncondensing)

10% to 90% relative humidity (without
removable media) or 20% to 80%
relative humidity (with removable
media); maximum wet bulb 2º C (36º F)
Nonoperating–4867 m (16,000 ft.);
Operating—2400 m (8,000 ft.)

Max. altitude
Nonoperating shock

30 G, 25 ms halfsine

Mechanical Specifications
Leave ventilation room around the system.

PK1015

Height

13 cm (5 in.)

Width

43 cm (17 in.)

Depth

46 cm (18 in.)

Weight

14.5 kg (32 lb)

Electrical Specifications
• Check your power supply setting.
•

Secure the power cord by turning the safety latch
clockwise over the power cord. Secure the latch by
tightening it with a screwdriver.
115V

230V

PK1047a

Front Buttons and LEDs
The LEDs are located in the lower right corner on the front
of the system.

PK1043a

Symbol

Function
Halt button. Suspends the operating
system and returns control to the SRM
console.
Environmental amber LED. On
indicates Temperature or Fan LEDs are
on. Flashes when operating system
invokes it as an alert.
Temperature amber LED. On
indicates internal temperature exceeds
operating conditions. The system shuts
down 30 seconds after this LED lights.
Fan amber LED. On indicates at least
one of the three fans in the system has
failed. The system shuts down 30
seconds after this LED lights.
Disk Activity green LED. Flashes
when internal system disks are accessed.
Power Present green LED. On when
power is present in the system.
Power button. Push in to start the
system and connect power. Push again
to remove power and stop the system.

Ethernet LEDs
The Ethernet LEDs are on the back of the system, lower
right corner.

Link
Speed/Activity

PK1050-99

LED
Link
Speed
Activity

Meaning
Steady green indicates Ethernet connection
Green for Ethernet speed of 100
Amber for Ethernet speed of 10
LED blinks with Ethernet activity

Beep Codes
The speaker in the front of the system reports errors using a
series of beeps.
Beeps
1-2-3
4
6
7

Meaning
Valid firmware image not found
Valid ROM header not found
Memory error (or bad checksum) detected
DIMMs in a memory bank do not match

PCI Slots
The SRM console command show config displays PCI
information.
PCI Slot 4

64 Bit

PCI Slot 3

64 Bit

PCI Slot 2

64 Bit

PCI Slot 1

32 Bit

PK1045-99

Memory Configuration
The SRM console command show memory displays the
memory configuration.
DIMM
BANKS

1
0
1
0
DIMM CONFIGURATION RULES:
• Always fill at least one bank (0 or 1).
• Use the same two DIMMs within a bank (size and vendor).
PK1046a

SRM Console Commands
alphabios

Loads and starts the AlphaBIOS console.

boot

Loads and starts the operating system.

clear envar

Resets an environment variable to its
default value.

clear password
continue

Sets the password to zero.
Resumes program execution.

crash

Forces a crash dump at the operating
system level.

deposit

Writes data to the specified address.

edit

examine
help

Invokes the console line editor on a RAM
file or on the nvram file (power-up
script).
Displays the contents of a memory
location, register, or device.
Displays information about the specified
console command.

initialize

Resets the system to a known state.

lfu

Runs the Loadable Firmware Update
Utility.

Turns off secure mode, enabling access to
all SRM console commands during the
current session.

Displays a file one screen at a time.

SRM Console Commands (continued)
prcache

Utility that initializes and displays status
of the optional PCI NVRAM device.

set envar

Sets or modifies the value of an
environment variable.

set host

Connects to an MSCP DUP server on a
DSSI device.

set password

Sets the console password for the first
time or changes an existing password.

set secure

Enables secure mode without requiring a
restart of the console.

show envar

Displays the state of the specified
environment variable.

show config

Displays the configuration at the last
system initialization.

show cpu

Displays the state of each processor in
the system.

show device

Displays a list of controllers and their
devices in the system.

show memory

Displays memory module information.

show pal

Displays the version of the privileged
architecture library code (PALcode).

show power

Displays information about the power
supplies, system fans, CPU fans, and
temperature.

show version

Displays the version of the console
program.

stop

Halts the specified processor. (Same as
halt.)

test

Runs firmware diagnostics for the
system.

Remote Management Console (RMC) Commands
alert_clr

Clears alert flag, stopping dial-out alert
cycle.

alert_dis

Disables the dial-out alert function.

alert_ena

Enables the dial-out alert function.

disable

Disables remote access to the modem port.

enable

Enables remote access to the modem port.

halt

Halts the system.

haltin

Causes a halt assertion.

haltout

Terminates a halt assertion created with
haltin.

hangup

Terminates the modem connection.

help or ?

Displays the list of commands.

poweroff

Turns off power.

poweron

Turns on power.

quit

Exits console mode and returns to system
console port.

reset

Resets the system. Emulates pressing the
Reset button.

setesc

Changes the escape sequence for invoking
command mode.

setpass

Changes the modem access password.

status

Displays system status and sensors.

Acoustics
Preliminary declared values per ISO 9296 and ISO 7779:
LWAd, B

LpAm, dBA
(bystander positions)

with 0xHDD
with RZ1DF

Idle

Operate

Idle

Operate

5.3
5.4

5.3
5.5

45
46

45
48

Current values for specific configurations are available from Compaq
representatives. 1 B = 10 dBA.

Schallemissionswerte — Vorläufige Werteangaben nach
ISO 9296 und ISO 7779/DIN EN27779:

mit 0xHDD
mit RZ1DF

Schalleistungspegel
LWad, B

Schalldruckpege
LpAm, dBA
(Zuschauerpositionen)

Leerlauf

Betrieb

Leerlauf

Betrieb

5,3
5,4

5,3
5,5

45
46

45
48

Aktuelle Werte für speziele Ausrüstungsstufen sind uber die Compaq
Computer Vertretungen erhältelich. 1 B = 10 dBA.

For More Information
• AlphaStation XP900 Console Reference
(EK-DS10V-CR)
•

AlphaStation XP900 Quick Setup (EK-DS10V-CP)

•

Using a Web browser, follow links to the appropriate
documentation from the URL:
http://www.compaq.com/products/workstations