Digital PDFs

EK-DS10S-UR-C01

2000

4 pages

Original

0.2MB

Document:	AlphaServer DS10 AlphaStation DS10 User Reference Card
Order Number:	EK-DS10S-UR
Revision:	C01
Pages:	4
Original Filename:

OCR Text

EK–DS10S–UR. C01

ALPHASERVER DS10
ALPHASTATION DS10
USER REFERENCE CARD
This document is intended as a quick reference for the
user. Additional information can be found in the
AlphaServer DS10 & DS10L / AlphaStation DS10
Console Reference guide, EK-DS10S-CR.
Overview
• Environmental Specifications

To reduce the risk of electrical shock or damage to the
equipment: Do not disable the power cord grounding
plug. The grounding plug is an important safety
feature. Plug the power cord into a grounded
(earthed) electrical outlet that is easily accessible at all
times. Disconnect power by unplugging the power
cord from the electrical outlet or the workstation.

Mechanical Specifications
Leave ventilation room at the front and rear of the system.

Environmental Specifications
Storage
temperature range

–40º C to 66º C
(–40º F to 151º F)

Operating
temperature range
Max. rate of change

Height

13 cm (5 in.)

10º C to 40º C
(50º F to 104º F)

Width

43 cm (17 in.)

Depth

46 cm (18 in.)

11º C (20º F) per hour

Weight

14.5 kg (32 lb)

Storage
humidity range
(noncondensing)

10% to 90% relative humidity;
maximum wet bulb 65º C (149º F)

•
•

Front Buttons and LEDs
Ethernet LEDs

•
•

Beep Codes
PCI Slots

Operating
humidity range
(noncondensing)

•
•

Memory Configuration
Front Access Drives (some Models)

10% to 90% relative humidity (without
removable media) or 20% to 80%
relative humidity (with removable
media); maximum wet bulb 2º C (36º F)
Nonoperating–4867 m (16,000 ft.);
Operating–2400 m (8,000 ft.)

•
•

SRM Console Commands
Remote Management Console (RMC) Commands

•

Acoustics

Nonoperating shock

Electrical Specifications
• Check your power supply setting (some models).
•

Secure the power cord by turning the safety latch
clockwise over the power cord. Secure the latch by
tightening it with a screwdriver.
115V

Mechanical Specifications
Electrical Specifications

230V

•
•

Max. altitude

PK1015

30 G, 25 ms halfsine

WARNING: To prevent injury, access is
limited to persons who have appropriate
technical training and experience. Such
persons are expected to understand the
hazards of working within this equipment and
take measures to minimize danger to
themselves or others.
PK1047a

CPU modules and memory modules have parts that
operate at high temperatures. Wait 2 minutes after
power is removed before touching any module.
Wear an antistatic wrist strap when working on this
system.

Front Buttons and LEDs
The LEDs are located in the lower right corner on the
front of the system.

Ethernet LEDs
The Ethernet LEDs are on the back of the system, lower right
corner.

PCI Slots
The SRM console command show config displays PCI
information.
PCI Slot 4

64 Bit

Link

PCI Slot 3

64 Bit

Speed/Activity

PCI Slot 2

64 Bit

PK1043a

Symbol

Function
Halt button. Suspends the operating
system and returns control to the SRM
console.
Environmental amber LED. On
indicates Temperature or Fan LEDs are
on. Flashes when operating system
invokes it as an alert.
Temperature amber LED. On
indicates internal temperature exceeds
operating conditions. The system shuts
down 30 seconds after this LED lights.
Fan amber LED. On indicates at least
one of the three fans in the system has
failed. The system shuts down 30
seconds after this LED lights.
Disk Activity green LED. Flashes
when internal system disks are accessed.

PCI Slot 1

PK1050-99

LED
Link
Speed
Activity

Meaning
Steady green indicates Ethernet connection
Green for Ethernet speed of 100
Amber for Ethernet speed of 10
LED blinks with Ethernet activity

Beep Codes
The speaker in the front of the system reports errors using a
series of beeps.
Beeps
1-2-3
4
6
7

Meaning
Valid firmware image not found
Valid ROM header not found
Memory error (or bad checksum) detected
DIMMs in a memory bank do not match

Power Present green LED. On when
power is present in the system.
Power button. Push in to start the
system and connect power. Push again
to remove power and stop the system.

32 Bit

PK1045-99

Memory Configuration
The SRM console command show memory displays the
memory configuration.
DIMM
BANKS

1
0
1
0
DIMM CONFIGURATION RULES:
• Always fill at least one bank (0 or 1).
• Use the same two DIMMs within a bank (size and vendor).
PK1046a

Front Access Drives (Some Models)
Front access disk drives are optional on some models.
Follow these steps to remove a drive or a spacer panel
from a front access bay.
1.

2.
3.

4.
5.

Ensure that the drive to be removed has been
properly dismounted (via the operating system)
before extracting it from the system.
Push the tab on the left of the drive
the extractor lever.

X to disengage

SRM Console Commands (continued)

SRM Console Commands
alphabios

Loads and starts the AlphaBIOS console.

boot

Loads and starts the operating system.

clear envar

Resets an environment variable to its
default value.

clear password
continue

Sets the password to zero.
Resumes program execution.

crash

Grasp the lever in the middle and pull it
forward; this will cause it to disengage the drive
from the flange on the right-hand side of the lever.
Pull the drive forward out of the bay.

Forces a crash dump at the operating
system level.

deposit

Writes data to the specified address.

If you need to remove a blank spacer panel, push
the tabs toward each other and pull the spacer
out.

examine

To replace the drive, slide it back into the bay,
secure the latches, and remount it.
3

edit

help

Displays the contents of a memory
location, register, or device.
Displays information about the specified
console command.

initialize

Resets the system to a known state.

lfu

Runs the Loadable Firmware Update
Utility.

more
1

Invokes the console line editor on a RAM
file or on the nvram file (power-up
script).

Turns off secure mode, enabling access to
all SRM console commands during the
current session.

prcache

Utility that initializes and displays status
of the optional PCI NVRAM device.

set envar

Sets or modifies the value of an
environment variable.

set host

Connects to an MSCP DUP server on a
DSSI device.

set password

Sets the console password for the first
time or changes an existing password.

set secure

Enables secure mode without requiring a
restart of the console.

show envar

Displays the state of the specified
environment variable.

show config

Displays the configuration at the last
system initialization.

show cpu

Displays the state of each processor in
the system.

show device

Displays a list of controllers and their
devices in the system.

show memory

Displays memory module information.

show pal

Displays the version of the privileged
architecture library code (PALcode).

show power

Displays information about the power
supplies, system fans, CPU fans, and
temperature.

show version

Displays the version of the console
program.

Displays a file one screen at a time.

2
MR0020

SCSI jumpers for front access drives are located on the
back of the front access drive cage. Default for the
drive located in the bottom slot is 0; default for the
upper drive is 1. See the label on the back of the cage
to change the jumpers if necessary.

stop

Halts the specified processor. (Same as
halt.)

test

Runs firmware diagnostics for the
system.

Remote Management Console (RMC)
Commands
alert_clr

Clears alert flag, stopping dial-out alert
cycle.

alert_dis

Disables the dial-out alert function.

alert_ena

Enables the dial-out alert function.

disable

Disables remote access to the modem port.

enable

Enables remote access to the modem port.

Acoustics
Declared values per ISO 9296 and ISO 7779, listed for the
server/workstation.
DS10 with 1 HDD

LWAd, B

LpAm, dBA
(operator
position)

LpAm, dBA
(bystander
positions)

5.7
6.0

48
52

41
45

Idle
Operating

Current values for specific configurations are available from Compaq
representatives. 1 B = 10 dBA.

halt

Halts the server.

haltin

Causes a halt assertion.

Schallemissionswerte — Vorläufige Werteangaben nach
ISO 9296 und ISO 7779/DIN EN27779:

haltout

Terminates a halt assertion created with
haltin.

DS10 mit
1 HDD

hangup

Terminates the modem connection.

help or ?

Displays the list of commands.

poweroff

Turns off power.

poweron

Turns on power.

Aktuelle Werte für speziele Ausrüstungsstufen sind uber die Compaq

quit

Exits console mode and returns to system
console port.

Computer Vertretungen erhältelich. 1 B = 10 dBA.

reset

Resets the server. Emulates pressing the
Reset button.

setesc

Changes the escape sequence for invoking
command mode.

setpass

Changes the modem access password.

status

Displays system status and sensors.

Leerlauf
Betrieb

Schalleistungspegel

Schalldruckpegel

LWAd, B

LpAm, dBA
(Bedienerposition)

LpAm, dBA
(Zuschauerpositionen)

5.7
6.0

48
52

41
45

For More Information
• AlphaServer DS10 / DS10L and AlphaStation DS10
Console Reference (EK-DS10S-CR)
•

AlphaServer DS10 Quick Setup (EK-DS10S-CP)

•

Using a Web browser, follow links to the appropriate
documentation from the URL:
http://www.compaq.com/showroom/